Big power, big cab. Big, new HYLAB cab. Powerful, reliable, customer proven features. Easy transportability and assembly

Transcription

1 Big power, big cab Big, new HYLB cab Totally new cab offers substantially more room and is designed to be highly functional and very comfortable 18, BTU air-conditioning 19, BTU hot water heating Six-way adjustable seat Easy-to-read backlit gauges djustable armrest console with pilot-operated single-axis controls for all hoisting functions Full function SML-1 load moment indicator monitored by load sensing via boom hoist mounted load cell Powerful, reliable, customer proven features 5' to 16' of 6" by 54" deep angle boom with heavy duty pendants 14' boom + 75' jib combination 218' maximum tip height and 19' maximum 36 working radius 12' maximum duty cycle boom 32,25 lbs dragline rating 55,596 lbs maximum line pull with 1 1/8" rope, front & rear Power load horsepower control Remote hydraulic cooler and dedicated engine cooler Free spooling third drum (front mount) and/or free fall fourth drum (rear mount) available vailable with auxiliary hydraulic system to power vibro/impact hammer, augers, hydraulic buckets, etc. - Includes auxiliary "spotter" / clamp circuits, easy-adjust variable fl ow control valve, boom foot mounted manifold, dedicated remote hydraulic cooler, spotter reservoir and fi ltration Easy transportability and assembly Hydraulic counterweight removal system Seven-piece counterweight design for easy transport Transports in 4 loads - under 85, lbs with boom base & hoist ropes World class features, outstanding severe duty capabilities, pin-point control, bullet-proof reliability and easy, fast transport... What are you waiting for? Link-Belt is a registered trademark. Copyright 24. ll rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifi cations. Litho in U.S.. 6/4 #4268

2 LS-38H II HYLB Series Lattice Crawler Crane 11-ton (99.79 mt) 11-ton (99.79 mt) at 12' (3.66 m) radius Powerhouse package: - 1-1/8" wire rope, front & rear drums - 37,1 lbs ( kg) allowable line pull - 55, lbs ( kg) available line pull - utomatic brake with true freefall - ttachments for lift crane, drag line and clam hp equipped with Power Load Rugged angle boom attachment for severe duty applications Separate engine/ hydraulic cooling Remote/dedicated hydraulic circuit* 4th drum with freefall* Remote hydraulic cooling for auxiliary attachment* * optional

3 LS-38H II HYLB Series Lightweight polymite sheaves reduce rope wear and are sealed and maintenance-free, giving HYLB owners outstanding reliability. ttachable bridle guide arms are used fast, easy bridle-to-boom connection for assembly and transport. Lattice Crawler Crane 11-ton (99.8 mt) Designed to meet the needs of both severe duty and general lift applications Robust boom, big rope, dedicated hydraulics Power Load pushes for optimal performance on the toughest jobs wesome operator control and comfort Non-slip safety strips and quick storage catwalks provide sure-footed access to the crane upper Hydraulic counterweight removal cylinders Optional self-assembly lifting sheaves Two boom base sections are available. The optional dragline base section is designed to allow lowering of the boom to ground with fairlead in place. Counterweight "biscuit" design allows for various configuration options. Self-cleaning 36" (.91 m) track shoes form a wide gauge of 17' 6" (5.33 m) when extended, and 11' 11.9" (3.65 m) when retracted. Lower structure ground clearance is 42" (1.7 m). Sealed (oil-filled) track rollers, idler and drive planetaries and compact hydrostatic drives add up to outstanding reliability and maintenancefree operation. Hydraulic cylinder in carbody for effortless extend/retract utomatic hydraulic track tension Carbody jacks standard HYLB hydraulic swing system smoothly rotates on turntable bearing with internal swing teeth. Upper secures into place with a four position positive house lock.

4 Power your hydraulic impact/vibratory hammer/tools direct with the LS-38H II optional hydraulic power package NO requirement for auxiliary power unit NO extra manpower to maintain and operate power unit NO cumbersome relocation of auxiliary power unit as crane moves NO added maintenance and cost of power unit NO contamination of crane s hydraulic system due to noncompatible hammer flows/poor filtration Put this added value feature on your crane, which includes separate high pressure high flow piston-style pump with Power Load. Cab-controlled variable flow control valve with lock foot-mounted manifold with main circuit and spotter and clamp circuits Separate oil cooler, separate sump tank with dedicated filtration Main hydraulic system has separate cooler, hydraulically-driven fan. Cooler hydraulics longer lasting, easy to clean (standard) Link-Belt's optional self-assembly lifting sheaves are efficient and simple to use. Plumbing for optional hydraulics includes manifold with spotter circuits, hook-up for auxiliary circuit, third drum connection and a "clamp" circuit for hammer application.

5 Optional hydraulic package has separate reservoir and cooling. Heavy duty hydraulic power meets your most demanding hoist needs 1-1/8" rope - front and rear drums 37,1 lbs ( kg) allowable line pull 55, lbs ( kg) available line pull Big drum brakes accessible, easy maintenance, adjustable for each individual operator hydraulic actuated 332 hp Mitsubishi engine provides plenty of reserve power to operate auxiliary hydraulic load Power Load total horsepower control challenges the engine at all times to work at maximum speed to give you maximum power a huge speed advantage over other cranes with bigger horsepower that do not use total horsepower control Remote hydraulic cooling Dedicated engine cooling Variety of counterweight configurations Optional front-mounted 3rd drum Optional high capacity 4th drum with true gravity freefall - 7/8" Optional auxiliary hydraulic power package for additional hydraulic supply for various attachments, controlled through a separate variable flow control valve in the operator s cab with system designed for cavitation/contamination, common with hydraulic hammers. Nephron filter system helps filter out fine contaminants. Power vibratory or impact hammer, augers, etc. wesome air, comfort and control at your fingertips The HYLB crane operations control center is ergonomically designed for maximum visibility, operating comfort and control with these standard features: 18,65 BTU air conditioning and 19, BTU heating run through upper and lower vents Rated capacity limiter with load cell located in boom hoist dead end Twist-o-grip swing/throttle lever Low effort hydraulic brake pedals minimal pedal travel Optional 4th drum foot pedal Optional variable flow auxiliary hydraulic circuit control rmchair mounted, pilot-operated hydraulic controls are designed to provide outstanding operator comfort. The location of the travel levers are offset, increasing the operator s overall visibility. Operator s cab console features include: Free-fall mode indicator Rated capacity limiter with suspension sensing nti-two block override switch hoist override switch Limit alarm indicator light System override switch and indicator light Front, rear and third drum lock switch Backlit instrumentation gauges with warning lamps cut here

6 Optimal transportability The LS-38H II moves in 4 loads with max boom, max jib and full counterweight. With its lightweight modular components, no other crane is faster, easier or more efficient to transport. Fast assembly and disassembly Counterweights are hydraulically installed and coupled to upper. Optional self-assembly lifting sheaves in base section dramatically simplify assembly, disassembly and load-out. Hydraulic cylinders in the boom base section pick up and handle the boom extensions, counterweights and treadmembers. You can remove counterweights, both sideframes and catwalks, pin the live mast and gantry, and be ready to load out. Reverse the process and be ready to stab boom in 45 minutes. cut here

7 vailable attachments provide strength and versatility Conventional open throat boom Rugged 6" x 54" (1.52 m x 1.37 m) in-line pin-connected angle boom attachment is a top notch performer in dragline, clamshell, pile driving and other severe duty cycle applications. Optional 25' (7.62 m) dragline base section 32,25 lbs ( kg) clam & drag ratings with 12' (36.58 m) of boom Heavy duty pendants Built to withstand side loads associated with duty cycle operation Main chord members are made with 1, psi yield material with high strength lattice. suspension is achieved through 1-part boom hoist reeving with dual pendant ropes. Standard equipment wear blocks protect lattice sections from wire rope scuffing. uxiliary 5' (1.5 m) tip extension Optional designed to provide clearance between two working hoist lines and jib open throat 14' + 75' ( m) angle boom + fixed jib 22' (67.6 m) maximum tip height Jib is common to other Link-Belt models. ll boom sections are manufactured in Lexington, Kentucky for fast, easy service, parts and replacement. Seamless welds and chrome plated hardware The boom top section features heavy duty steel sheaves and standard pin-on points for attachment of options such as a fixed jib, tip extension and adapters for universal pile driving leads with quick reeve ability. J3 J3 J3 In-line boom suspension load cell, standard with anti-two block system for both front and rear drum and jib - open throat Conventional open throat boom with 5' auxiliary tip Lexington, Kentucky Link-Belt is a registered trademark. Copyright 21. ll rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications. Litho in U.S.. 11/1 #4267 (supersedes #4256)

8 5421 (supersedes 541) J3 1 Technical Data Specifications & Capacities Crawler Crane 11 Ton (1 metric ton) CUTION: This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual to determine allowable crane lifting capacities and operating procedures.

9 5421 (supersedes 541) J3 This Page Intentionally Blank

10 5421 (supersedes 541) J3 1 5 (15.24 m) (6.39 m) (4.4 m) (3.18 m) (3.3 m) (3.45 m) (1.43 m) 7 5 (2.26 m) (6.37 m) 36 (.9 m) 12 (.3 m) (4.72 m) 17 6 (5.33 m) - Extended (3.65 m) - Retracted

11 (supersedes 541) J (3.2m) (3.45m) 4 6 (1.37m) (3.63m) Retracted (3.21m) (6.37m) (1.29m) 7 1 (2.39m) Transport Weight Rope on both drums, Treadmembers, Backstops, Catwalks and full tank of fuel 127,584 lb (57 871kg) (2.98m) Carbody (3.63m) (6.73m) (2.49m) (4.73m) Extended 1 5 (3.18m) Upper & Carbody Shipping Weight Rope on both drums, backstops, catwalks, and full tank of fuel 86,26 lb (39 21kg) 43 (1.9m) (1.18m) (8.44m) 58 (1.47m) (7.78m) (6.36m) 25 (7.62m) ngle Top Section ngle: 5,57 lb (2 294kg) 25 (7.62m) ngle Base Section Plate Base : 5,528 lb (2 57kg) Lattice Base : 4,66 lb (2 114kg) 36 (.9m) Treadmembers w/36 (.9m) Shoes 23,543 lb (1 679kg) --- each (1.31m) 14 (4.27m) (.75m) (1.1m) (9.52m) 3 (9.1m) Basic Jib ssembly Tube: 1,676 lb (76kg) (1.1m) 3 5 (1.4m) Upper Counterweight Base Slab: 1,143 lb (4 61kg) (.44m) (.44m) Third Drum Without Rope 955 lb (433kg) Carbody Jack Minimum and Maximum Heights 16, 992 lb (7 77kg) (1.41m) (1.1m) Left Wing Counterweight 6,836 lb (3 11kg) (1.25m) (1.1m) Right Wing Counterweight 6,615 lb (3 1kg) Rear Mount, Fourth DrumKit(WithoutRope) 3,796 lb (1 722kg) 16 (.41m) 12 4 (3.76m) 42 (1.7m)

12 5421 (supersedes 541) J HYLB 5 Transportation Weights and Dimensions Base Crane: Rigid Backstops, 132 gal (5 L) of fuel, Catwalks (right and left side), 25 ft (6.1m) Base Section, Bridle and Bail Bar, Hoist Reeving, 7 ft (213.36m) of type DB Front Hoist Rope, 7 ft (213.36m) of type RB Rear Hoist Rope. Item Description Gross Weight Transport Loads Notes and Load Summary lb kg #1 #2 #3 #4 Numbers in the load columns to the left Base Crane 86, represent quantities. dd Counterweight (base ctwt., 1 left wing and 1 right wing) 23, dd Left Wing B Counterweights 6, Estimated transport assumes the load dd Right Wing B Counterweights 6, out consists of 16 ft (48.77m) of tube Remove Base Section --5, boom + 75 ft (22.86m) of jib with full counterweight. dd Treadmembers 23, dd Hydraulic Third Drum w/o rope dd 3rd Drum Wire Rope.75 x 55 Type DB Support loads were targetedt at 45, lb (2 412kg), 8 ft 6 in(2.6m) wide, 48 dd25ft(7.62m) ngle boom Top Section 4, ft (14.6m) long, and 13 ft 6 in(4.1m) dd Three--sheave assembly to top section high using a drop deck trailer. This may dd Three--sheave Idler /C vary depending di on state t laws, empty truck/trailer weights, and style of trailer. dd1ft(3.5m) ngle Extension w/pins & pendants 1, dd2ft(6.1m) ngle Extension w/pins & pendants 2,65 1, dd3ft(9.1m) ngle Extension w/pins & pendants 3,625 1, Estimated weights vary by +/-- 2%. dd Tagline Winder w/rope Estimated Total Load #1 dd Fairleader 1, ,158 lb (38 627kg) dd Pile Driving dapter dd15ft(4.57m) Tubular Jib Peak ssembly Estimated Total Load #2 44,13 lb (2 17kg) dd15ft(4.57m) Tubular Jib Base and Strut ssembly 1, dd15ft(4.57m) Tubular Jib Extension Estimated Total Load #3 dd5ft(1.5m) uxiliary Tip Extension ,925 lb (19 924kg) dd Fourth Drum 3, Estimated Total Load #4 dd 2--ton (18.14mt) Hook Ball -- Swivel or Non Swivel 1, ,375 lb (14 232kg) dd 75--ton (68.4mt) 2--Sheave Hook Block 2,2 998 dd 11--ton (1mt) 3--Sheave Hook Block 2, Remove Front Hoist Rope 1.12 in x 7 ft Type DB --1, Remove Jib Wire Rope 1.12 in X 7 ft Type RB --1, Remove 25 ft (7.62m) ngle Base Section (ssy Complete) --4, Remove 5 gal (189.3L) of Fuel HYLB 5 Crane Working Weight Option Description Base Crane equipped with 5 ft (15.24m) of angle boom, counterweight, 7 ft (213m) front hoist rope, 1 7 ft (198m) rear hoist rope, 11--ton (99.8mt) hook block, 132 gal (5.4L) of fuel, and 2 lb (9.7kg) operator. Option #1 plus B counterweight and 11 ft (33.53m) of boom extensions to obtain 16 ft (48.77m) of main 2 boom. Option #2 plus 75 ft (22.86m) of jib and 2--ton (18.14mt) hook ball -- subtract 2 ft (6.1m) of boom 3 extension and to obtain maximum ft ( m) of main boom + jib. Notes: 1. Ground bearing pressure is based on the total weight distributed evenly over the track contact area. 2. Total contact area for 36 in (.91m) track shoes is 16,12 in 2 (1 126cm 2 ). Gross Weight lb (kg) 164,353 (74 549) 25,45 (93 17) 26,4 (93 442) Ground Bearing Pressure psi (kg/cm 2 ) 1.26 (.72) (.9) (.91)

13 (supersedes 541) J3 ttachment Options J ft ngle ( m) Basic ngle ft (15.24m) two---piece design that utilizes a 25 ft (7.62m) base section and a 25 ft (7.62m) top section with in---line connecting pins. extensions are 6 in (1.52m) wide and 54 in (1.37m) deep at outside dimensions of angles. S feet on in (1.2m) centers S 4inx4inx.5in(11.6mm x 11.6mm x 12.7mm) angle chords S Lugs on base section to attach carrying links S Skywalk platform S Deflectorrollerontopsection S Rigid sheave guards S Tip extension and jib connecting lugs on top section S angle indicator S Three in (.63m) root diameter lift sheaves mounted on sealed anti---friction bearings with rope guards. S Quick---align bridle guide for pinning bridle to boom base. S Includes two 1.12 in (28.4mm) parallel grooved bolt---on Lebus lagging Optional Head Machinery --- S For clamshell operations: Two in (.63m) root diameter lift sheaves mounted on sealed anti---friction bearings with three---piece rope guide rollers. S For lift crane and/or dragline operations: Two in (.63m) root diameter lift sheaves and one in (.63m) root diameter wide mouth dragline sheave mounted on sealed anti---friction bearings with four---piece rope guide rollers. Includes one parallel and one spiral grooved bolt---on Lebus lagging instead of standard. Revolving Upper Structure J Frame ll welded steel frame with precision machined surfaces for mating parts. J Engine Mitsubishi 6D24--TL2E with oil filter, oil cooler, air cleaner, fuel filter, water separator, tachometer and electrical shutdown. Number of cylinders 6 Bore and stroke -- in (mm) Piston displacement -- in 3 (cm 3 ) 5.12 x 5.91 (13 x 15) 729 (11 945) Engine rpm at full load speed 2, Hi--idle rpm 2, Full load speed -- hp (kw) 332 (248) Peak torque -- ft lb (joule) 918 (1 245) Peak torque -- rpm 1,4 Electrical system Batteries 24 volt volt S For dragline operations: One in (.63m) root diameter wide mouth drag sheave with two---piece rope guide rollers. Includes two spiral groove bolt--- on Lebus lagging instead of standard. ngle Extensions --- The following table provides the lengths available and the suggested quantity to obtain maximum boom in 1 ft (3.5m) increments. Midpoint pendant connections are not required. ngle Suggested Quantity for Extensions Max. 1 ft (3.5m) 1 2 ft (6.1m) 2 3 ft (9.14m) 2 S ppropriate length pendants S Maximum angle boom tip height of 166 ft (5.6m) J ft Tubular Jib ( m) Basic Tube Jib ft (9.14m) two --- piece design that utilizes a 15 ft (4.57m) base section and a 15 ft (4.57m) top section with in---line connecting pins on 32 in (.81m) wide and 24 in (.61m) deep centers. S 2 in(5.8mm) diameter tubular chords S One 2.62 in (.52m) root diameter polymide sheave mounted on sealed anti---friction bearings. S 15 ft (4.6m) jib extensions provide jib lengths at 45 ft (13.76m), 6ft(18.3m) and 75 ft (22.86m) for angle boom. S Jib offset angles at 1 and 3 S Maximum tip height angle boom + jib is 22 ft (67.1m). pproximate fuel consumption gal./hr (L/hr) 1% H.P. 16 (6.56) 75% H.P. 12 (45.42) 5% H.P. 8 (3.28) 25% H.P. 4 (15.14) J Hydraulic System Specifications Hydraulic Pumps --- The pump arrangement is designed so that all functions are hydraulically powered allowing positive, precise control with independent or simultaneous operation of all crane functions. S Power Load with horsepower control provides onboard computer monitoring of hydraulic pump demands, allowing maximum speed under load when pumps are operated independently. J uxiliary Tip Extension Designed to use in place of jib to provide 5 ft(1.5m) clearance between working hoist lines. The extension is equipped with two polymide 21 in (.53m) root diameter sheaves mounted on sealed anti---friction bearings. Maximum capacity is 2 ton (18.14mt). J Hoist System Designed to lift off maximum boom or maximum boom plus jib unassisted. Operates up to a maximum boom angle of 82. hoist limit system limits maximum boom angle operation. S Retractable gantry frame S Pin --- on bail frame S Ten---part reeving with 3/4 in (19mm) wire rope S Bridle assembly S Two 1.5 in (38.1mm) pendants S Tubular boom backstops (telescopic type) S Sheaves contain sealed anti---friction bearings S speed from is 62 seconds with no load. Speed was determined using 11 ft (33.53m) of angle boom. S When heavy loads are handled by one or more pumps simultaneously, Power Load prevents engine overload while still delivering maximum available power. S When the unit is equipped with the optional auxiliary hydraulic circuit, Power Load control gives priority to the auxiliary hydraulics, allowing uninterrupted operation of the auxiliary hydraulic function while still allowing for multiple machine function. S Two variable displacement pumps operating at 4,554 psi (32kg/cm 2 )and 15 gpm (397 Lpm) powerloadhoist drum, boom hoist drum, optional third drum, optional fourth drum, and travel. S One fixed displacement gear type pump operating at 3,555 psi (25kg/cm 2 ) and 6 gpm (227 Lpm) powers the swing motors.

14 5421 (supersedes 541) J3 5 Revolving Upper Structure --- (continued) S One fixed displacement gear type pump operating at 3,27 psi (25kg/cm 2 ) and 16 gpm (61Lpm) powers the jack cylinders, swing motors and counterweight removal. S One fixed displacement gear type pump operating at 1, psi (7.3kg/cm 2 ) and 11 gpm (42Lpm) powers the remote control valves. S One fixed displacement gear type pump operating at 2,571 psi (18kg/cm 2 ) and 8.5 gpm (32.1Lpm) operates the remote oil cooler fan. S One fixed displacement gear type pump operating at 35.7 psi (2.5kg/cm 2 ) and 6.4 gpm (24.2Lpm) supplies drive gear box cooling. Pump Control ( Fine Inching ) mode --- Special pump setting, selectable from operator s cab, that allows very slow movements of load hoist drums, boom hoist drum, and travel for precision work. Hydraulic Reservoir gal (49 L), equipped with sight level gauge. Diffusers built in for deaeriation. Filtration --- One 1 micron, full flow, line filter in the control circuit. ll oil is filtered prior to entering the reservoir. Remote Oil Cooler --- Oil cooler, located behind the operator s cab, has a hydraulically driven thermostatically controlled fan to control oil temperature. Counterbalance Valves --- ll hoist motors are equipped with counterbalance valves to provide positive load lowering and prevent accidental load drop if the hydraulic pressure is suddenly lost. Optional Hydraulic Circuit --- The optional hydraulic power package offers additional hydraulic supply for various attachments controlled through a separate variable flow control valve. This system eliminates pump cavitation and contamination often found in use with hydraulic hammers and other auxiliary tools. The flow from the number one main auxiliary pump goes through a variable flow control valve which is adjustable from the cab. Hydraulic fittings connect to a hydraulic manifold located at the boom foot. Return oil from the attachment is cooled by a separate remote hydraulic oil cooler, filtered by two separate filter systems, andstoredinaseparatehydraulicreservoir. System includes: Number One Main uxiliary Circuit --- open loop S 98 gpm (37Lpm) maximum flow pump with operating pressure up to 4,5 psi (316kg/cm 2 ), able to maintain 98 gpm (37Lpm) S Bi---directional control valve with adjustable relief valve S Remote control operation from operator s cab with detent locks at 25%, 5%, 75%, and 1% flow S Separate 51 gal (194L) capacity hydraulic reservoir S Separate remote mounted full flow hydraulic oil cooler with hydraulic driven cooling fan, thermostatically controlled S Full flow 1 micron return line filter S Nephron filtration system (constant ultra---fine filtration of hydraulic system) Possible applications/uses: S Hydraulic impact hammer (pile driving) S Hydraulic vibratory hammer (pile driving) S Various drills/augers S Hydraulic clamshell bucket (open close circuits) S Powering generator (magnet operation) Number Two uxiliary Pump Circuit --- open loop S 16 gpm (61Lpm) at 3,27 psi (23kg/ cm 2 ) maximum S Three---section directional control valve (allows 3 separate remote hydraulic circuits) Possible applications/uses: S Spotter circuits for pile driving S Hose reel operation Number Three uxiliary Pump Circuit --- open loop S 8.7 gpm (33Lpm) piston type pump S 4,571 psi (321kg/cm 2 ) operating pressure Possible applications/uses: S Hydraulic vibratory pile driving hammer/clamp circuit (for pile driving extraction) J Load Hoist Drums Each drum contains a pilot controlled, bi---directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. S Power up/down & free---fall operation modes S utomatic brake mode (spring applied, hydraulically released, band type brake) S 1.12 in (28.4mm) grooved lagging S Drum pawl controlled manually S Drum rotation indicators S Mounted on anti---friction bearings S 22 in (.56m) root diameter S 43.3 in (1.1m) flange diameter S 27.1 in (.69m) width Note: The freefall operational mode is designed to prevent load lowering even if the freefall switch is accidentally activated.theautomaticbrakemodemeets all OSH requirements for personnel handling. Drum Clutches --- Speed --- o --- Matict power hydraulic two shoe clutch design that uses a 37 in (94mm) diameter x 5.5 in (139.7mm) wide shoe that internally expands to provide load control. Swept area is 638 in 2 (4 116cm 2 ). J Optional Front Mounted Third Hoist Drum The hydraulic winch is attached to the frontoftheupperframeandisusedin conjunction with a fleeting sheave and 3---sheave idler assembly to run the wire rope over the boom top section. S Free---spooling capability for pile driving applications S in (.32m) root diameter S in (.58m) flange diameter S 17 in (.43m) drum width S Mounted on anti---friction bearings J Optional Rear Mounted Fourth Hoist Drum The hydraulic winch is pinned to the rear oftheupperframeandusedinconjunction with the fleeting sheave and threesheaveidlersleevetorunthewirerope over the boom top section. S in (.45m) root diameter S in (.88m) flange diameter S in (.34m) drum width S Mounted on anti---friction bearings S Grooved lagging for 7/8 in (22mm) wire rope S Drum contains a bi---directional axial piston motor and a gear reduction unit to provide positive control under all load conditions. S Power up/down and free---fall operation modes. S utomatic brake mode (spring applied hydraulically released band---type brake) S Manualdrumpawlcontrol S The free---fall mode designed to prevent load lowering even if the free---fall switch is accidentally activated. The automatic brake mode meets all OSH requirements for personnel handling. J Hoist Drum Contains a pilot controlled, bi---directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. S Spring applied, hydraulically released, disc---type brake controlled automatically S.75 in (19mm) grooved lagging S Drum pawl controlled automatically S Mounted on anti---friction bearings S in (.5m) root diameter S in (.86m) flange diameter S 9.82 in (.25m) width

15 (supersedes 541) J3 J Swing System Pilot controlled bi---directional axial piston motors and the planetary gear reduction unit to provide positive control under all load conditions. S Spring applied, hydraulically released, 36 multi --- plate brake S Free swing mode when lever is in neutral position S Four position positive house lock S Two---speed swing S udio/visual swing alarm S Maximum swing speed is 2.9 rpm J Counterweight Removable, seven---piece design consisting of a base slab pinned in place with quick disconnect hydraulic cylinders and wing counterweights held in place with chain and ratchet tie---downs. Two counterweight configuration options: S ,668 lb (1 736kg) --- Base plus a left and right wing counterweights, and tie---down chains, ratchets, and bolts S B --- 5,851 lb (23 66kg) --- Base plus six wing counterweights (three left and three right), and tie---down chains, ratchets, and bolts Counterweight components S Base slab --- 1,143 lb (4 61kg) S Left wing --- 6,836 lb (3 11kg) each S Right wing --- 6,615 lb (3 1kg) each J Operator s Cab and Controls Fully enclosed modular steel compartment is independently mounted and insulated to protect against vibration and noise. S ll tinted/tempered safety glass S Sliding entry door and front window S Padded for noise reduction S 19, BTU hot water heater S 18,6 BTU air conditioner S Defroster S Door and window locks S Circulating fan S Sun visor S Engine instrumentation panel --- Tachometer, voltmeter, engine oil pressure, engine water temperature, fuel level, hydraulic oil temperature, hour meter, service monitor system S Electronic drum rotation indicators for front and rear hoist drums S Six---way adjustable cloth seat S Dry chemical fire extinguisher S Fully adjustable single axis arm chair controls S Swing lever with twist---grip throttle, swing brake, and horn located on handle S Foot throttle S Bubble---type level S Ergonomic gauge layout S Control shut---off lever S Right hand control stand is adjustable by electric motor for operator comfort S Windshield wiper & washer J Rated Capacity Limiter System The SML---1 rated capacity limiter (RCL) monitors crane functions with high accuracy sensors and continuously compares the lifted load with the crane capacity chart. If an overload condition is approached, the operator is warned with audible and visual alarms. This system provides a continuous display of: S Ratedloadorloadradius S ctual load S Percentage of load S ngle of main boom S Crane configuration S Length of main boom S Jib angle, jib offset, or radius of jib load Operator settable alarms can be quickly set for each jobsite to provide a method for obstacle avoidance by limiting minimum and maximum boom angle, radius, and maximum tip height. J dditional Equipment --- Standard S 71.2 in (1.8m) outside diameter turn---table bearing S Right and left side removable catwalks S 132 gal (5 L) fuel tank (usable quantity) S Machine lifting links J dditional Equipment --- Optional S Rud --- o --- maticr model #1848 tagline winder S Full revolving type Fairleader with barrel, sheaves, and guide rollers. Lower Structure J Lower Frame ll welded box construction frame with precision---machined surfaces for turntable bearing and rotating joint S 1 ft 8 in (3.25m) overall width S 11 ft 11 in (3.6m) overall length J Treadmembers ll welded, precision---machined, steel frames can be hydraulically extended and retracted by a hydraulic cylinder mounted in the lower frame. S 14 ft 6 in (4.42m) extended gauge S 9ft(2.74m) retracted gauge S 2 ft 11 in (6.37m) overall length S 36 in (.9m) wide track shoes S 11 sealed (oil filled) track rollers per treadmember S Sealed (oil filled) idler and drive planetaries S Compact travel drives S Hydraulic adjusting tracks Travel and Steering --- Each treadmember contains a pilot controlled, bi---directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. S Individual control provides smooth, precise maneuverability including full counter---rotation. S Spring applied, hydraulically released disc type brake controlled automatically. S Maximum travel speed is 1.13 mph (1.82km/h). S Designed to 3% gradeability. J Carbody Jacks System contains four hydraulic cylinders individually mounted on swing out beams. S Individual controls are mounted on carbody. S Minimum height of carbody when resting on pontoons is 16 in (.41m). S Maximum height of carbody when resting on pontoons is 42 in (1.7m).

16 5421 (supersedes 541) J HYLB 5 Load Hoisting Performance vailable line speed and line pull -- based on Mitsubishi 6D24--TLZE at 2, rpm full load speed. Line pulls are not based on wire rope strength. See Wire Rope Capacity Chart for maximum permissible single part of line working loads. Front or Rear Drum - 1 1/8 in (28.4mm) WireRope Rope Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 55, , , , , , , , , , Hoist Drum - 3/4 in (19mm) Wire Rope Rope Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 36, , , , , , , , Rear Mounted Fourth Drum - 7/8 in (22.2mm) Wire Rope Rope Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 39, , , , , , , , Front Mounted Third Drum - 3/4 in (19mm) Wire Rope Rope Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 22, , , , , , Wire Rope pplication Diameter Length Maximum Permissible Load Type in mm ft m lbs kg Main Hoist 11/ DB 37, uxiliary Hoist 11/ RB 28, Hoist 3/ W 16, Third Drum 3/ DB 16, Fourth Drum 7/ DB 22, Rope Type DB RB N W Description 6 x 26 (6 X 19 Class) -- Warrington Seale -- Extra Improved Plow Steel -- Preformed -- Right Lay -- Regular Lay -- I.W.R.C. 19 x 19 Rotation Resistant -- Extra Improved Plow Steel -- Preformed -- Right Lay -- Regular Lay -- Swaged -- SF=5.1 6 x 25 (6 x 19 Class) -- Filler wire, extra improved plow steel, preformed, independent wire rope center, right lay, alternate lay 6 x 26 (6 x 19 Class) -- Extra improved plow steel, preformed, independent wire rope center, right lay, alternate lay

17 (supersedes 541) J3 WRNING RED ND UNDERSTND THE OPERTOR S ND SFETY MNULS ND THE FOLLOWING INSTRUCTIONS ND CHRT VLUES BEFORE OPERTING THE CRNE. OPERTION WHICH DOES NOT FOLLOW THESE INSTRUCTIONS MY RESULT IN N CCIDENT. THIS DOCUMENT IS INTENDED FOR REFERENCE USE ONLY. Lifting Notes General: 1. Rated lifting capacities in pounds as shown on lift charts pertain to this crane as originally manufactured and normally equipped. Modifications to the crane or use of optional equipment other than that specified can result in a reduction of capacity. 2. Construction equipment can be dangerous if improperly operated or maintained. Operation and maintenance of this crane must be in compliance with the information in the Operator s, Parts, and Safety Manuals supplied with the crane. If these manuals are missing, order replacements through the distributor. 3. The operator and other personnel associated with the crane shall read and fully understand the latest applicable merican National Standards Institute (NSI) safety standards for cranes. 4. ll capacities listed in this book are in compliance with SME/NSI B3.5 at time of manufacture. Lift Crane Operation: 1. Capacities shown are in pounds and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, etc. When using main hook while jib is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Hook With Jib Installed. When using main hook while 5 ft tip extension or pile driver lead adapter is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Hook With 5 ft Tip Extension or Pile Driver Lead dapter Installed. See Operator s Manual for all limitations when raising or lowering attachment. 2. The crane capacities in the shaded areas are based on structural strength. The crane capacities in the non--shaded areas are based on stability. 3. For recommended reeving, parts of line, wire rope type, and wire rope inspection, see Wire Rope Capacity Chart, Operator s Manual, and Parts Manual. Rated lifting capacities are based on correct reeving. Deduction must be made for excessive reeving. ny reeving over minimum required (see Wire Rope Capacity Chart) is considered excessive and must be accounted for when making lifts. Use Working Range Diagram to estimate the extra feet of rope. See Wire Rope Capacity for the weight to deduct for each extra foot of wire rope before attempting to lift a load. 4. Rated lifting capacities in the Crane Rating Manual are based on freely suspended loads and make no allowances for such factors as the effect of ground conditions and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. 5. Rated lifting capacities do not account for the effects of wind on a suspended load or boom. Lifting capacities should be considered acceptable for wind speeds less than 2 mph and appropriately reduced for wind speeds greater than 2 mph. (See General Wind Restrictions Guide.) 6. The capacities listed are for the crane equipped with or without live mast and with the gantry in the raised position. 7. The least stable rated condition is over the side. 8. s should be erected and lowered over the end for maximum stability. See Liftoff Capabilities before erecting or lowering boom. 9. Do not operate at radii and boom lengths where the Crane Rating Manual lists no capacity. Do not use longer booms or jibs than those listed in the Crane Rating Manual. ny of the above can cause a tipping condition, or boom and jib failure. 1. These capacities apply only to the crane as originally manufactured and normally equipped by Link--Belt Construction Equipment Company. For Over End Blocked Capacities Only: 1. These capacities can be lifted over either end with the crane standing level on a firm supporting surface with adequate blocking placed under the treadmember sprockets/idlers to prevent rocking. 2. Do not travel with a load. Traveling With Load: 1. ll 36 rotation capacities listed in the Crane Rating Manual are pick and carry capacities. 2. The boom must be pointing straight over one end of the crawler lower. If the load was lifted over the side, swing the load over the end and/or if the load was lifted at a long radius and the load is at or near capacity for that radius, boom up to obtain a greater lifting capacity before beginning travel. 3. Engage the swing lock and apply swing brake. 4. Travel slowly and cautiously on a firm and level--supporting surface. Definitions: 1. Load Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of the vertical hoist line or tackle with load applied. 2. ngle: The angle between the boom base section and horizontal with freely suspended load at the rated radius. 3. Working rea: rea measured in a circular arc about the centerline of rotation as shown on the Working rea Diagram. 4. Freely Suspended Load: Load hanging free with no direct external force applied except by the hoist line. 5. Side Load: Horizontal side force applied to the lifted load either on the ground or in the air.

18 5421 (supersedes 541) J3 9 Parts of Line Type DB Type RB Wire Rope Capacity 11/8in 3/4 in 7/8 in Type M Type LB Type LB Type DB Notes 1 37,1 28,6 37,1 4,8 16,8 22,7 Capacities shown are in pounds and 2 74,2 57, ,6 33,6 45,4 working loads must not exceed the 3 111,3 85, ,4 5,4 68,1 ratings on the capacity charts in the Crane 4 148,4 114, ,2 67,2 9,8 Rating Manual ,5 143, , 84, 113, ,6 171, ,8 1,8 136,2 Rope wt per foot LBCE Type Description DB LB RB* M Study Operator s Manual for wire rope inspection procedures. 6 x 26 (6 x 19 Class) -- Warrington Seale -- Extra Improved Plow Steel -- Preformed -- Right Lay -- Regular Lay -- I.W.R.C. 6 Strand, Compacted Strand, Seale or Warrington Seale, I.W.R.C., Preformed Right Lay -- Regular Lay 19 x 19 Rotation Resistant-- Extra Extra Improved Plow Steel -- Preformed -- Right Lay -- Regular Lay. Swaged -- SF = 5:1 6 x 25 (6 x 19 Class) -- Filler Wire -- Extra Improved PLow Steel -- Preformed -- Independent Wire Rope Center -- Right Ly, Lang Ly Notes: 1. Capacities shown are in pounds and working loads must not exceed the ratings on the capacity charts in the Crane Rating Manual. 2. Study Operator s Manual for wire rope inspection procedures and single part of line applications. Over Idler End See Note Longitudinal Of Crawler Working reas 36_ Over Side Center Of Rotation Over Drive End Counterweight () NO (RETRCTED) NO (EXTENDED) (RETRCTED) (EXTENDED) B (EXTENDED) Counterweight () NO (RETRCTED) NO (EXTENDED) (RETRCTED) (EXTENDED) B (EXTENDED) Notes: Liftoff Capabilities Maximum Over End (Gantry In Raised Position) Maximum + Jib 8 N/ 1 N/ 11 N/ 13 N/ (See Note 4) Over Side (Gantry In Raised Position) Maximum Maximum + Jib 8 N/ 1 N/ 11 N/ 13 N/ For maximum boom and maximum boom + jib combinations only -- adequate blocking must be placed under side frame sprockets/idlers to prevent rocking. The ramps supplied with the crane are considered to be adequate blocking. 2. Crane on firm and level surface. 3. Gantry pins must be installed with the gantry in the raised position. 4. For maximum stability, booms must be erected and lowered over the end blocked with no load and with the hook block on the ground. Idler Sprocket See Note Drive Sprocket Over Side Note: These Lines Determine The Limiting Position Of ny Load For Operation Within Working reas Indicated.

19 (supersedes 541) J3 General Wind Restrictions Guide WRNING Failure to follow these wind speed restrictions may result in structural failure of the boom, which would cause property damage and/or bodily injury. 1. The effects of the wind force on the hook load are the responsibility of the user and are not taken into account. When hoisting any load in windy conditions, the load wind area and load controllability must be considered for safe crane operation. 2. Wind speed is to be determined at the boom top section. Wind Speed Chart and + Jib Lengths: ft DESCRIPTION LLOWBLE WINDSPEEDS 1. Normal Lifting Operation. (See Capacity Charts.) --2 mph Base Self ssembly Lifting Sheaves Capacities Radius ngle (deg) Capacity , ,5 Notes: 1. Rated capacities are for 36_ rotation. 2. Gantry must be pinned in the raised position when lifting loads with the sheaves in the base section. 3. Backstops must be assembled to base section. 4. For self assembly/disassembly of counterweights, boom extensions, and side frames only. 5. Rated capacities are for extended or retracted side frames with or without counterweight or on carbody jacks without counterweight. 6. Reeve boom base section self assembly lifting sheaves with front drum rope only. 2. Reduced Operation. Capacities must be reduced by 2%. 3. Reduced Operation. Capacities must be reduced by 4%. 4. Reduced Operation. Capacities must be reduced by 7%. 4. No Operation. Store ttachment On Ground mph mph mph Over 45 mph Crane ssembly Component Weights Component ft Top Section With 3--Sheave Lift/Drag Head Machinery, with Basic Pendants ft Top Section With 3--Sheave Lift/Drag Head Machinery and 5 ft Tip Extension With Basic Pendants ft Plate Base Section With Lifting Sheaves 25 ft Lattice Base Section With Lifting Sheaves 4. Extensions Weight lb kg 5, , ,528 4, S 1 ft Extension With Pendants 1, S 2 ft Extension With Pendants 2, S 3 ft Extension With Pendants 3, Upper Counterweights S Counterweight Base Slab Counterweight 1 Left Wing Counterweight 1 Right Wing Counterweight S Counterweight B 2 Left Wing Counterweights 2 Right Wing Counterweights Left Wing Counterweights (each) Right Wing Counterweights (each) 23, , ,615 6, (Each) 23, Tube Jib Including Strut, Head Machinery, and Pendants S 3 ft Tube Jib ssembly 1, S 15 ft Extension With Pendants

20 5421 (supersedes 541) J3 11 Dragline Working Range Diagram Length Maximum Digging Depth Maximum Dumping Height Inhaul Rope Radius Limit Maximum Digging Depth Maximum Digging Radius Notes: 1. geometry shown is for unloaded condition and crane standing level on firm supporting surface. deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length.

21 (supersedes 541) J3 Clamshell Working Range Diagram 13 Length Maximum Digging Depth Maximum Dumping Height Open Working Bucket Height 6. Closed Working Bucket Height Maximum Digging Depth Maximum Digging Radius Notes: 1. geometry shown is for unloaded condition and crane standing level on firm supporting surface. deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length.

22 5421 (supersedes 541) J The capacities included in the Duty Cycle Capacities -- ngle curve are the maximum allowable, and are based on an 38 HYLB 5 crawler crane with B (5,851 lb) or (23,668 lb) counterweight standing level on firm supporting surface under ideal job conditions. 2. Capacities are based on 75% of minimum tipping loads for dragline; 67.5% for clamshell. 3.Capacities are maximum recommended by PCS Standard #4. Operator must make allowances for soft or uneven supporting surfaces, rapid cycle operations, bucket suction, or other unfavorable conditions which may require smaller buckets for most efficient operation. Duty Cycle Notes For ngle 4. Weight of bucket plus load must not exceed these capacities. 5. Dragline operation is not recommended with boom angles less than length for dragline/clamshell attachment operation should not exceed 12 ft. 7. Retractable high gantry must be pinned in the raised position for all capacities on the Duty Cycle Capacities -- ngle curve. 8. These capacities apply to the crane as originally manufactured and normally equipped by Link--Belt Construction Equipment Company. Length Load Radius ngle (deg) B Ctwt 36 Rotation Extended Dragline Clamshell Magnet Ctwt 36 Rotation Extended Dragline Clamshell Magnet , , , , , , , , , , , , , , , , , , , , , , ,25 32,25 32,25 32, ,25 32,25 32,25 32, ,25 32,25 31,3 28, , , , , , , , , , , , , , , , , , , , , , , , , ,25 32,25 32,25 32, ,25 32,25 3,9 27, ,5 32,25 22,4 2, , , , , , , , , , , , , , , , , , , , , , , ,25 32,25 3,5 27, ,1 28,8 22, 19, ,9 22,4 16,7 15, , , , , , , , , , , , , , , , , , , , , , , ,7 28,5 21,7 19, ,5 22, 16,4 14, ,6 17,6 12,8 11, ,4 -- 9, Length Load Radius ngle (deg) B Ctwt 36 Rotation Extended Dragline Clamshell Magnet Ctwt 36 Rotation Extended Dragline Clamshell Magnet , , , , , , , , , , , , , , , , ,4 28,2 21,3 19, ,2 21,7 16, 14, ,3 17,3 12,4 11, ,1 -- 8, ,7 -- 7, , , , , , , , , , , , , , , , , ,8 21,4 15,7 14, ,9 17, 12, 1, ,3 13,7 9,4 8, ,3 -- 6, ,4 -- 5, , , , , , , , , , , , , , , ,4 21, 15,3 13, ,5 16,6 11,7 1, ,9 13,4 9, 8, ,2 1,9 7, 6, , -- 4, ,4 -- 3, , , , , , , , , , , , , , , ,1 16,2 11,3 1, ,5 13, 8,6 7, ,8 1,6 6,6 5, ,7 8,7 5,1 4, ,2 -- 3, ,8 -- 2,4