Technical Data. Specifications & Capacities. HSL Crawler Crane 80 Ton (72.6 metric ton) P8

Transcription

1 1 Technical Data Specifications & Capacities HSL Crawler Crane Ton (72.6 metric ton) CAUTION: This material is supplied for reference use only. Operator must refer to in--- cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. Link-Belt Cranes 138 HSL

2 138 HSL Link-Belt Cranes

3 Table Of Contents Upper Structure... 1 Frame... 1 Engine... 1 Hydraulic System... 1 Hoist Drums... 1 Optional Front--- Mounted Third Hoist Drum... 1 Optional Rear---Mounted Fourth Hoist Drum... 2 Boom Hoist Drum... 2 Swing System... 2 Counterweight... 2 Operator Cab... 2 Rated Capacity Limiter System... 2 Boom Hoist System... 2 Machinery Cab... 2 Catwalks... 2 Lower Structure... 3 Carbody... 3 Side Frames... 3 Travel and Steering... 3 Optional... 3 Attachment and Options... 3 Conventional Tubular Boom... 3 Angle Boom... 4 Tubular Jib... 4 Auxiliary Tip Extension... 4 Dimensions... 5 Base Crane... 7 Side Frames... 7 Upper Counterweights... 8 Boom... 9 Jib Hook Balls Hook Blocks Working Weights Transport Weights Transport Drawings -- Tube Boom Hoist Performance Working Areas Attachments Tube Boom Make--up Tube Boom Working Range Diagram Tube Boom Chart Angle Boom Make--up Angle Boom Working Range Diagram Link-Belt Cranes 138 HSL

4 Angle Boom Chart Jib Attachment Make-- up Tube Boom + Jib Working Range Diagram Tube Boom + Jib Charts Angle Boom + Jib Working Range Diagram Angle Boom + Jib Charts HSL Link-Belt Cranes

5 Upper Structure Frame Hydraulic System Hoist Drums 1 All welded steel frame with precision machined surfaces for mating parts. Turntable Bearing S Inner race with internal swing gear is bolted to lower frame. S Outer race bolted to upper frame. Engine Engine Full pressure lubrication, oil filter, air cleaner, hour meter, throttle, and electric control shutdown. Isuzu AH--6HK1X Number of cylinders 6 Bore and stroke Piston displacement Engine rpm at full load speed Hi --- idle rpm Gross engine hp Peak torque Electrical system Fuel tank capacity Batteries Approximate fuel consumption 4.53 x 4.92 in (115 x 125mm) 475 in 3 (7.8L) 2,000 rpm 2,050 rpm 287 hp (214kw) 838 ft lb (1 1,500 rpm 24 volt 110 gal (415L) volt gal/hr (L/hr) % hp 14. (54.51) 75% hp (43.65) 50% hp 8.28 (31.34) 25% hp 4.20 (15.90) Fuel Tank Equipped with fuel sight level gauges, flame arrester, and self---closing cap with locking eye for padlock. Hydraulic Pumps The pump arrangement is designed to provide hydraulically powered functions allowing positive, precise control with independent or simultaneous operation of all crane functions. S Two variable displacement pumps operating at 4,550 psi (320kg/cm 2 )and 74 gal/min (2L/min) powers load hoist drums, boom hoist drum, optional third drum, optional fourth drum, and travel. S One variable displacement pump operating at 4,625 psi (325kg/cm 2 )and 31.7 gal/min (120L/min) powers the swing motor and side frame. S One fixed displacement gear type pump operating at 2,985 psi (210kg/cm 2 ) and 15.9 gal/min (60L/min) powers the remote mounted hydraulic oil cooler fan. S One fixed displacement gear type pump operating at 1,420 psi (kg/cm 2 ) and 10.8 gal/min (41L/min) powers the hydraulic remote control system and hydraulic counterweight self---assembly system. S One fixed displacement gear type pump operating at 1,420 psi (kg/cm 2 )and8.4gal/min(32l/min) powers the optional tagline winch. Pump Control ( Fine Inching ) Mode Special pump setting, selectable from the operator s cab, that allows very slow movements of load hoist drums, boom hoist drum, and travel for precision work. Hydraulic Reservoir 66 gal (250L), equipped with sight level gauge. Diffusers built in for deaeriation. Filtration Ten micron, full flow, line filter in the control circuit. All oil is filtered prior to entering the reservoir. Counterbalance Valves All hoist motors are equipped with counterbalance valves to provide positive load lowering and prevent accidental load drop if the hydraulic pressure is suddenly lost. Each drum contains an axial piston, variable speed hydraulic motor with individual automatic winch motor brakes. Power flow is directed through a patented, semi---outboard mounted, wet style multi---disc brake. The brake is mounted on the output side of the planetary, which greatly reduces drag associated with most wet style brakes in free---fall mode. S Power up/down & free---fall operation modes S Automatic brake mode (spring applied, hydraulically released, wet type brake) S Drum lagging grooved for wire rope S Drum pawl controlled manually S Electronic drum rotation indicators S Mounted on anti---friction bearings S 19.2 in (488mm) root diameter S 33.1 in (8mm) flange diameter S 21.7 in (551mm) width The free---fall operation mode is designed to prevent load lowering even if the free--- fall switch is accidentally activated. The automatic brake mode meets all OSHA requirements for personnel handling. Optional Front---Mounted Third Hoist Drum The hydraulic winch is pinned to the front oftheupperframeandisusedinconjunction with a fleeting sheave and 3---sheave idler assembly to run the wire rope over the boom top section. S Controlled free spooling capability for pile driving applications. S 10.6 in (270mm) root diameter S 20 in (508mm) flange diameter S 13.5 in (343mm) width S Mounted on anti---friction bearings Link-Belt Cranes 138 HSL

6 P8 Optional Rear---Mounted Fourth Hoist Drum Drum contains an axial piston, variable speed hydraulic motor with individual automatic winch motor brakes. Power flow is directed through a patented, semi---outboard mounted, wet style multi---disc brake. S Power up/down & free---fall operation modes S Automatic brake mode (spring applied, hydraulically released, wet type brake) S Drum lagging grooved for wire rope S Drum pawl controlled manually S Electronic drum rotation indicators S Mounted on anti---friction bearings S 19.2 in (488mm) root diameter S 30.7 in (7mm) flange diameter S 19 in (483mm) width S Pins to rear of upper frame S Plumbing and valving standard with main unit The free---fall operation mode is designed to prevent load lowering even if the free--- fall switch is accidentally activated. The automatic brake mode meets all OSHA requirements for personnel handling. Boom Hoist Drum Contains a pilot controlled, bi---directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. S Spring applied, hydraulically released, disc type brake controlled automatically S 0.63 in (15.88mm) grooved lagging S Drum pawl controlled manually S Mounted on anti---friction bearings S 17.7 in (450m) root diameter S 28 in (711mm) flange diameter S 8.9 in (226mm) width Swing System Mechanically controlled bi---directional axial piston motor and planetary gear reduction unit to provide positive control under all load conditions. S Spring applied, hydraulically released, 360 multi --- plate brake S Free swing mode when lever is in neutral position S Two position positive house lock S Audio/Visual swing alarm S Maximum swing speed is 3.0 rpm Counterweight Consists of a three---piece design that can be easily lowered to the ground using the gantry. S A upper counterweight consists of one, 23,305 lb (10 571kg) base slab S B upper counterweight consists of one, 16,944 lb (7 686kg) weight S C upper counterweight consists of one, 12,071 lb (5 475kg) weight Total combined counterweight is 52,320 lb (23 732kg). Operator Cab Fully enclosed modular steel compartment is independently mounted and padded to protect against vibration and noise. S All tinted/tempered safety glass S Folding hinge entry door andsliding front glass window S 19,000 BTU hot water heater S 18,600 BTU air conditioner S Door and window locks S Circulating fan S Sun visor S Cloth seat S Defroster S Windshield wipers and washer S Dry chemical fire extinguisher S Engine instrumentation panel (voltmeter, engine oil pressure, engine water temperature, fuel level, hydraulic oil temperature, hour meter, and service monitor system) S Electronic drum rotation indicators for front and rear hoist drums S Six way adjustable seat S Hand and foot throttle S Fully adjustable single axis controls S Swing lever with swing brake and horn located on handle S Bubbletypelevel S Ergonomic gauge layout S Controls shut off lever S Control stand is adjustable for operator comfort. Rated Capacity Limiter System The HSL rated capacity limiter system is a boom hoist, dead end load cell system. This system provides the operator with useful geometrical data, to include: S Main Boom Length S Main Boom Angle S Jib Length S Jib Angle S Operating Mode S S Boom Tip Height S Audible Alarm S Pre---Warning Light S Overload Light S On Hook S Function kick---outs including over load S Operator settable stops (ramped stops) S Anti---Two Block Indicator Boom Hoist System Designed to lift off maximum boom or maximum boom plus jib unassisted. Operates up to a maximum boom angle of. Boom hoist limit system limits maximum boom angle operation. S 14---part reeving with 16mm (0.63 in) wire rope S 22 ft (6.71m) live mast S Bridle assembly S Two 1.25 in (32mm) pendants S Dual telescoping type backstops S Sheaves contain sealed anti---friction bearings S Boom speed from is 34.5 seconds with no load. Speed was determined using ft (24.38m) of angle boom. Machinery Cab Hinged doors (four on right side, three on left side) for machinery access. Storage/ rigging box located on operator s side of upper house. Equipped with rooftop access ladder and skid resistant finish on roof. Catwalks Standard on right and left sides. Catwalks are removable for reduced travel width. 138 HSL Link-Belt Cranes

7 Lower Structure Carbody Lower Frame All welded high strength steel [65,000 psi (448.16MPa) yield] box construction frame with precision machined surfaces for turntable bearing and rotating joint. S 9ft2.3in(2.m) overall width S 11 ft 10.9 in (3.63m) overall length Side Frames Side Frames All welded, precision machined, steel frames can be hydraulically extended and retracted by a hydraulic cylinder mounted in the lower frame. S 14 ft (4.27m) extended gauge S 8ft11in(2.72m) retracted gauge S 20 ft 2 in (6.25m) overall length S 36 in (0.91m) wide track shoes S Sealed (oil filled) idler and drive planetaries S Compact travel drives S Hydraulic self adjusting tracks Track Rollers S Eleven sealed (oil filled) track rollers per side frame S Heat treated, mounted on oil filled anti--- friction bearings Tracks Heat treated, self---cleaning, multiple hinged track shoes joined by one---piece full floating pins; 52 shoes per side frame Take Up Idlers Cast steel, heat treated, self---cleaning, mounted on aluminum/bronze bushings. Lubricated through idler shaft. Attachment and Options Conventional Tubular Boom ft ( m) Basic Boom ft (12.19m) two---piece design that utilizes a 20 ft (6.10m) base section and a20ft(6.10m) open throat top section with in---line connecting pins on 54 in (1.37m) wide and 44 in (1.12m) deep centers. S Boom foot on 43.5 in (1.10m) centers S 3in(7.62cm) diameter chords S Lugs on base section for self assembly S Deflectorrollerontopsection S Permanent skid pads mounted on top section to protect head machinery S Rigid sheave guards S Five, 18 in (0.46m) root diameter steel sheaves mounted on sealed anti---friction bearings S Mechanical boom angle indicator Optional Handling system that mounts in the boom base to allow loading/unloading of counterweights or a boom section. Tube Boom Extensions The following table provides the lengths available and the suggested quantity to obtain maximum boom in 10 ft (3.05m) increments. Midpoint pendant connections are required at ft (24.38m) for boom lengths of 170 ft (51.m) thru 200 ft (60.96m). Travel and Steering 3 Travel and Steering Each side frame contains a pilot controlled, bi---directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. S Individual control provides smooth, precise maneuverability including full counter---rotation. S Spring applied, hydraulically released disc type brake controlled automatically S Maximum travel speed is 1.0 mph (1.61km/h) in high speed and 0.6 mph (1km/h) in low speed. S Designed to 30% gradeability Optional S Rud --- o --- matic model 1248 tagline winder for angle boom (double barrel, spring wound, drum type) Tube Boom Extensions ft m Quantity For Max Boom S Wear bars on top of each section S Appropriate length pendants S Maximum tip height of 204 ft (62.18m) S Boom connecting pins storage on each extension Link-Belt Cranes 138 HSL

8 P8 Angle Boom ft ( m) Basic Angle Boom ft (12.19m) two---piece design that utilizes a 20 ft (6.10m) base section and a20ft(6.10m) top section with in---line connecting pins on 45.7 in (1.16m) wide and 45.7 in (1.16m) deep centers. S Boom foot on 43.5 in (1.10m) centers S 4inx4inx0.38in(10.16cm x 10.16cm x 0.97cm) angle chords S Lugs on base section to attach carrying links S Deflectorrollerontopsection S Permanent skid pads mounted on top section to protect head machinery S Rigid sheave guards S Four, 18 in (0.46m) root diameter steel sheaves mounted on sealed anti---friction bearing S Mechanical boom angle indicator Optional Three sheave head machinery for clam applications Angle Boom Extensions The following table provides the lengths available and the suggested quantity to obtain maximum boom in 10 ft (3.05m) increments. Midpoint pendant connections are not required. Angle Boom Extensions ft m Quantity For Max Boom Tubular Jib ft ( m) Basic Tube Jib 30 ft (9.14m) two---piece design that utilizes a 15 ft (4.57m) base section and a 15 ft (4.57m) top section with in---line connecting pins on 32 in (0.81m) wide and 24 in (0.61m) deep centers. S 2 in(50.8mm) diameter tubular chords S One in (0.47m) root diameter steel sheave mounted on sealed anti--- friction bearings S 15 ft (4.57m) jib extensions provide jib lengths of 45 ft (13.72m) and 60 ft (18.29m). S Jib offset angles at 5, 15, and25 S The maximum tip height of boom + jib is 242 ft (73.76m) using the tube boom and 204 (62.18m) using the angle boom. Auxiliary Tip Extension Designed for use with tube boom up to 190 ft (57.91m) to use in place of jib to provide clearance between working hoist lines. The extension is equipped with a single 18 in (0.45m) root diameter nylon sheave mounted on sealed anti---friction bearings. Maximum capacity is 9 Ton (8.16mt). S Deflector roller on top of each section S Appropriate length pendants S Maximum tip height of 154 ft (46.94m). 138 HSL Link-Belt Cranes

9 Dimensions 5 General Dimensions English Metric Basic Boom ft 12.19m Minimum 10 ft 2.75 in 3.19m Maximum Boom Angle Track Shoe Width 36 in 0.91m Maximum height of live mast from ground is 29 2 (8.89m) 23 9 ** (7.24m) 8 11 (2.72m) 3 8 (1.12m) 12 2 (3.71m) 14 2 (4.32m) Note: **@ Maximum boom angle ( ) with maximum boom [200 ft (60.96m)], maximum rotation radius occurs. Link-Belt Cranes 138 HSL

10 P8 Tailswing 14 2 (4.32m) 10 6 (3.20m) 36 (0.91m) (5.97m) Extended (4.23m) Retracted 17 0 (5.18m) Extended (3.63m) Retracted (4.28m) (3.21m) 39 (0.99m) 15.2 (0.39m) 14 0 (4.27m) Extended 8 11 (2.72m) Retracted 138 HSL Link-Belt Cranes

11 7 Base Crane Base Crane Length 1 20 ft 2 in (6.15m) Length 2 37 ft 6 in (11.43m) Length 3 2 ft 6 in (0.76m) Height 11 ft 0 in (3.35m) Weight: Tube Boom 88,121 lb (39 971kg) Angle Boom 88,826 lb ( 291kg) H L3 L1 L2 Side Frames Side Frames Length 20 ft 2 in (6.15m) Width 36 in (0.91m) Height 39 in (0.99m) Weight 19,700 lb (8 936kg) W L H Number inside black circle = # of components Link-Belt Cranes 138 HSL

12 P8 Upper Counterweights W A Slab Counterweight Length 46 in (1.17m) Width 10 ft 6 in (3.20m) Height 6ft6.25in (1.99m) Weight 23,305 lb (10 571kg) L H W B Slab Counterweight Length 46 in (1.17m) Width 10 ft 6 in (3.20m) Height 23 in (0.58m) Weight 16,944 lb (7 686kg) L H C Slab Counterweight W Length in (1.10m) Width 10 ft 6 in (3.20m) Height in (0.65m) Weight 12,071 lb (5 475kg) L H Number inside black circle = # of components 138 HSL Link-Belt Cranes

13 9 Boom 54 in (1.37m) x 44 in(1.12m) Tube Boom Extensions 10 ft (3.05m) Extension Weight: 510 lb (231kg) 48 (1.22m) (1.50m) 10 4 (3.15m) N6P0001 N6P (1.50m) 20 ft (6.10m) Extension Weight: 851 lb (386kg) 48 (1.22m) 20 4 (6.20m) N6P0001 N6P ft (9.14m) Extension Weight: 1,207 lb (547kg) 48 (1.22m) (1.50m) 30 4 (9.25m) N6P0001 N6P in (1.16m) x 45.7 in (1.16m) Angle Boom Extensions 10 ft (3.05m) Extension Weight: 847 lb (384kg) 52 (1.32m) (1.49m) 10 4 (3.15m) (1.49m) 20 4 (6.20m) 20 ft (6.10m) Extension Weight: 1,424 lb (646kg) 52 (1.32m) (1.49m) 30 4 (9.25m) 30 ft (9.14m) Extension Weight: 2,067 lb (938kg) 52 (1.32m) Link-Belt Cranes 138 HSL

14 P8 L 20 ft (6.10m) Tube Boom Top Section Length 21 ft 11 in (6.68m) Width in (1.45m) Deep 44 in (1.12m) Height 51 in (1.30m) Weight 2,350 lb (1 066kg) W D H L 20 ft (6.10m) Angle Boom Top Section Length 22 ft 5 in (6.83m) Width in (1.25m) Deep 45.7 in (1.16m) Height 50 in (1.27m) Weight 2,930 lb (1 329kg) D W H 20 ft (6.10m) Tube Boom Base Section L Length 20 ft 6 in (6.25m) Width in (1.50m) Deep 44 in (1.12m) Height 61 in (1.55m) Weight w/o Quick Draw 1,701 lb (772kg) w/ Quick Draw 2,210 lb (1 002kg) W D H 20 ft (6.10m) Angle Boom Base Section L Length 20 ft 6 in (6.25m) Width in (1.29m) Deep 45.7 in (1.16m) Height 61 in (1.55m) Weight w/o Quick Draw 2,454 lb (1 113kg) w/ Quick Draw 2,915 lb (1 322kg) D W H Number inside black circle = # of components * --- Optional equipment 138 HSL Link-Belt Cranes

15 11 Auxiliary Tip Extension* Length in (1.79m) Width in (0.62m) Height in (1.09m) Weight 900 lb (8kg) L W H Jib 15 ft (4.57m) Jib Top Section* Length 16 ft 1.50 in (4.91m) Width in (0.88m) Height in (0.67m) Weight 544 lb (247kg) Weight includes pendants and hardware. L W H 15 ft (4.57m) Jib Base Section* L Length 15 ft 3.50 in (4.66m) Width in (0.88m) Height in (0.67m) Height in (1.38m) Weight 936 lb (425kg) Weight includes pins, basic frontstay & backstay pendants, and hardware. W H1 H2 15 ft (4.57m) Jib Extension* Length 15 ft 2.50 in (4.64m) Width in (0.88m) Height in (0.67m) Weight 330 lb (150kg) Weights includes pins, pendants, and hardware. L W H Number inside black circle = # of components * --- Optional equipment Link-Belt Cranes 138 HSL

16 P8 Hook Balls 15 Ton (13.6mt) Swivel Hook Ball* Width in (0.44m) Height.50 in (1.03m) Weight 767 lb (348kg) W H 15 Ton (13.6mt) Non --- Swivel Hook Ball* Width 18 in (0.46m) Height in (1.00m) Weight 748 lb (339kg) W H Number inside black circle = # of components * --- Optional equipment 138 HSL Link-Belt Cranes

17 13 Hook Blocks 50 Ton (45.4mt) 4---Sheave Hook Block* W1 W2 Width in (0.58m) Width in (0.51m) Width in (0.48m) Height in (1.37m) Weight 1,221 lb (554kg) H W3 W1 W2 Ton (72.6mt) 4---Sheave Hook Block* Width in (0.63m) Width in (0.46m) Width in (0.51m) Height in (1.52m) Weight 1,221 lb (554kg) H W3 Number inside black circle = # of components * --- Optional equipment Working Weights Based on basic crane including Isuzu AH---6HK1X diesel engine, turntable bearing, live mast, 14 part boom hoist reeving, backstops, crawler lower with 36 in (0.91m) wide track shoes, sealed track rollers, and catwalks, plus the following: Lifting crane --- includes ft (12.19m) basic tubular boom, quickdraw cylinder, 700 ft (213.36m) of 16mm type DB front hoist rope, 700 ft (213.36m) of 16mm type DB rear hoist rope, Ton (72.6mt) hook block, and basic pendants. Ground Bearing Pressure Ctwt A Ctwt AB Ctwt ABC lb (kg) 116,388 (52 793) lb (kg) 133,332 (60 478) lb (kg) 145,3 (65 954) psi kg/cm Link-Belt Cranes 138 HSL

18 P8 Transport Weights Base Crane: Telescoping Boom Backstops, 27 gal (102.2L) Of Fuel, Side Frames, Catwalks, 20 (6.10m) Tube Base Section, 24 (7.32m) Live Mast with Bridle, Part Boom Hoist Reeving, 700 (213.36m) Type DB Front Hoist Rope, and 700 (213.36m) Type DB Rear Hoist Rope. Item Description Gross Weight Base Crane 88, Transport s lb kg #1 #2 #3 Add A Counterweight 23, Add B Counterweight 16, Add C Counterweight 12, Add Hydraulic Third Drum Without Rope 1, Add 20 (6.10m) Tube Top Section 2, Add 10 (3.05m) Tube Extension With Pins And Pendants Add 20 (6.10m) Tube Extension With Pins And Pendants 1, Add 30 (9.14m) Tube Extension With Pins and Pendants 1, Add 20 (6.10m) Angle Base Section 2, Add 20 (6.10m) Angle Top Section With 4 Lifting Sheaves 2, Add 20 (6.10m) Angle Top Section With 3 Lifting Sheaves 2, Add 20 (6.10m) Angle Top Section With 2 Lifting Sheaves 2, Add 10 (3.05m) Angle Extension With Pins And Pendants 1, Add 20 (6.10m) Angle Extension With Pins And Pendants 1, Add 30 (9.14m) Angle Extension With Pins and Pendants 2, Add Tagline Winder Add 30 (9.14m) Tube Jib 1, Add 15 (4.57m) Tube Jib Extension Add 5 (1.52m) Auxiliary Tip Extension Add Holding Rope --- 7/8 in X 165 (50.29m) Type DB Add Closing Rope --- 7/8 in X 220 (67.06m) Type DB Add Inhaul Rope --- 7/8 in X 105 (32.00m) Type M Add Hoist Rope --- 7/8 in X 210 (64.01m) Type LB Add Jib Wire Rope --- 7/8 in X 700 (213.36m) Type DB Add 3rd Drum Wire Rope mm X 385 (117.35m) Type ZB Add 3rd Drum Wire Rope mm X 385 (117.35m) Type WB Add ton (13.6mt) Hook Ball --- Non Swivel Add ton (13.6mt) Hook Ball --- Swivel Add ton (45.3mt) 4 Sheave Hook Block 1, Add ---ton (72.6mt) 4 Sheave Hook Block 1, Add Quick Draw Remove 20 (6.10m) Tube Base Section ---2, Remove Front Hoist Rope --- 7/8 in X 700 (213.36m) Type DB Remove Jib Wire Rope --- 7/8 in X 5 (164.59m) Type RB ---1, Remove 22 (6.71m) Live Mast with Bridle ---2, Remove 50 gal (190L) Of Fuel Approximate Total Shipping Weight lb 88,121 37,723 29,932 kg Notes: Estimated weights vary by ± 2%. Numbers in the transport loads columns represent quantities. Estimated transport loads assume the load out consist of 200 (60.96m) of tube boom and 60 (18.29m) of jib with full counterweight. Support loads were targeted at 45,000 lb (20 412kg), 8 6 (2.6m) wide, 48 (14.6m) long, and 13 6 (4.1m) high using a drop deck trailer. This may vary depending on state laws, empty truck/trailer weights, and style of trailer. 138 HSL Link-Belt Cranes

19 15 Transport Drawings --- Tube Boom (3.93m) 34 (0.86m) LOAD # ,121 lb (39 971kg) Base crane (4.14m) 34 (0.86m) LOAD # ,391 lb (16 960kg) B & C counterweights, 20 ft (6.10m) tube boom top section, 20 ft (6.10m) tube boom extension with pins and pendants, two 30 ft (9.14m) tube boom extensions with pins and pendants, 15 ton (13.6mt) non---swivel hook ball, and ton (72.6mt) 4 sheave hook block (3.85m) 34 (0.86m) LOAD # ,792 lb (13 513kg) A counterweight and cylinders, 10 ft (3.05m) tube boom extension with pins and pendants, 20 ft (6.10m) tube boom extension with pins and pendants, 30 ft (9.14m) tube boom extension with pins and pendants, 30 ft (9.14m) basic tube jib, and two 15 ft (4.57m) tube jib extensions. Link-Belt Cranes 138 HSL

20 P8 Hoist Performance FrontorRearDrum-- 7/8 in Wire Rope Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 31, , , , , , Boom Hoist Drum -- 16mm Wire Rope Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 23, , , , , , Front Mounted Third Drum mm Wire Rope Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 15, , , , , , Rear Mounted Fourth Drum -- 7/8 in Wire Rope Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 35, , , , , Diameter Max. Permissible Wire Rope Application in mm Type lb kg Wire Rope Descriptions Boom Hoist LB 11, Strand, Compacted Strand, Seale or Warrington Seale, I.W.R.C., Preformed, Right Lay, Regular Lay Front Drum 7/ DB 22, X26(6X19Class),WarringtonSeale,E.I.P.S., Preformed, Right Regular Lay, I.W.R.C. Rear Drum (Optional) 7/ RB 17, X 19 Rotation Resistant Compacted Strand --- High Strength --- Preformed, Right Regular Lay Rear Drum (Optional) 7/ DB 22, X26(6X19Class),WarringtonSeale,E.I.P.S., Preformed, Right Regular Lay, I.W.R.C. Third Drum (Optional) ZB 11, X 7 Non---Rotating, E.I.P.S., Right Regular Lay, Compacted Third Drum (Optional) WB 13, Strand, Preformed, Regular Lay Fourth Drum (Optional) 7/ RB 23, X 19 Rotation Resistant Compacted Strand --- High Strength --- Preformed, Right Regular Lay 138 HSL Link-Belt Cranes

21 Working Areas Over Side Boom See Note Over Idler End Longitudinal Of Crawler Center Of Rotation Over Drive End Idler Sprocket See Note Drive Sprocket Over Side Note: These Lines Determine The Limiting Position Of Any For Operation Within Working Areas Indicated. Link-Belt Cranes 138 HSL

22 P8 Attachments Offset Jib Auxiliary Tip Extension Main Boom Main Boom Main Boom ft ( m) Main Angle Boom ft ( m) Main Tube Boom ft ( m) Main Tube Boom With Tip Extension --1 ft ( m) Main Tube Boom With ft ( m) Offset Jib 138 HSL Link-Belt Cranes

23 Tube Boom Make---up 19 Boom Length (12.19) 50 (15.24) 1 Tube Boom Extensions 10 (3.05) 20 (6.10) 30 (9.14) 60 (18.29) 1 70 (21.34) 1 (24.38) (27.43) 1 1 (30.48) (33.53) (36.58) (39.62) 3 1 (42.67) (45.72) (48.77) (51.82) (54.86) (57.91) (60.96) Notes: 1. Capacities shown are in kips/metric tons (1 kip = 1,000 lb / 1 metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. A deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, load weighing device, etc. When using main hook while jib or tip extension is attached, reduce capacities by values shown in Crane Rating Manual. See Operator s Manual for all limitations when raising or lowering attachment. 2. The capacities in the shaded areas are based on structural strength. The capacities in the non---shaded areas are based on stability ratings. 3. For recommended reeving, parts of line,wire rope type, and wire rope inspection, see Wire Rope Capacity Chart, Operator s Manual, and Parts Manual. 4. ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 5. The 22 ft (6.71m) live mast must be used for all capacities listed. 6. The least stable rated condition is over the side. 7. Booms must be erected and lowered over the end for maximum stability. 8. Main boom length must not exceed 200 ft (60.96m). 9. Do not operate at radii and boom lengths where the Crane Rating Manual lists no capacity. Do not use longer booms or jibs than those listed in the Crane Rating Manual. Any of the above can cause a tipping condition, or boom and jib failure. 10. These capacities are in compliance with ASME/ANSI B30.5 at date of manufacture. 11. These capacities apply only to the crane as originally manufactured and normally equipped by Link-Belt Construction Equipment Company. Optional Auxiliary Tip Extension Link-Belt Cranes 138 HSL

24 P8 Tube Boom Working Range Diagram Main Boom Length Maximum Boom Angle SeeNote Tube Boom Height Above Ground Minimum Boom Angle SeeNote LC ofrotation 60 Notes: 1. Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length Operating from Centerline of Rotation HSL Link-Belt Cranes

25 Tube Boom Chart 21 Tube Boom Lift Capacity Chart _ Rotation ABC = 52,320 lb (23 732kg) Counterweight -- Side Frames Extended [All capacities are listed in kips (mt)] 50 (15.2) 60 (18.3) 70 (21.3) Boom Length --- (24.4) 90 (27.4) 110 (33.5) 120 (36.6) 130 (39.6) 11 (3.4) (72.6) 12 (3.7) (72.6) (72.6) 13 (4.0) (68.9) (68.8) 14 (4.3) (64.2) (64.1) (64.0) 15 (4.6) (60.1) (60.1) (60.0) 16 (4.9) (56.6) (56.5) (56.4) (56.2) 17 (5.2) (53.3) (53.3) (53.2) (53.1) 18 (5.5) (50.4) (50.4) (50.3) (50.2) (49.4) 19 (5.8) (46.1) (46.2) (46.3) (46.3) (46.3) 99.3 (45.0) 20 (6.1) 93.7 (42.5) 93.9 (42.6) 94.0 (42.6) 94.1 (42.7) 94.1 (42.7) 94.0 (42.6) 25 (7.6) 67.0 (30.4) 67.1 (30.4) (30.4) 67.1 (30.4) 67.0 (30.4) 66.9 (30.3) 66.8 (30.3) 30 (9.1) 51.8 (23.5) 51.9 (23.5) 52.0 (23.6) 52.0 (23.6) 51.9 (23.5) 51.8 (23.5) 51.7 (23.5) 51.6 (23.4) 51.5 (23.4) 51.4 (23.3) 35 (10.7) 42.0 (19.1) 42.2 (19.1) 42.2 (19.1) 42.1 (19.1) 42.1 (19.1) 42.0 (19.1) 41.9 (19.0) 41.8 (19.0) 41.6 (18.9) 41.5 (18.8) 35.1 (15.9) 35.3 (16.0) 35.3 (16.0) 35.3 (16.0) 35.2 (16.0) 35.1 (15.9) 35.0 (15.9) 34.9 (15.8) 34.7 (15.7) 34.6 (15.7) 50 (15.2) 26.3 (11.9) 26.4 (12.0) 26.4 (12.0) 26.3 (11.9) 26.2 (11.9) 26.0 (11.8) 25.9 (11.7) 25.8 (11.7) 25.6 (11.6) 60 (18.3) 20.8 (9.4) 20.7 (9.4) 20.6 (9.3) 20.4 (9.3) 20.3 (9.2) 20.2 (9.2) 20.0 (9.1) 70 (21.3) 16.9 (7.7) 16.7 (7.6) 16.6 (7.5) 16.5 (7.5) 16.3 (7.4) 16.2 (7.3) (24.4) 14.0 (6.4) 13.8 (6.3) 13.7 (6.2) 13.5 (6.1) 13.4 (6.1) 90 (27.4) 11.7 (5.3) 11.6 (5.3) 11.4 (5.2) 11.3 (5.1) 9.9 (4.5) 9.8 (4.4) 9.6 (4.4) 110 (33.5) 8.4 (3.8) 8.3 (3.8) 120 (36.6) 7.1 (3.2) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. Link-Belt Cranes 138 HSL

26 P8 Tube Boom Lift Capacity Chart _ Rotation ABC = 52,320 lb (23 732kg) Counterweight -- Side Frames Extended [All capacities are listed in kips (mt)] 1 (42.7) 150 (45.7) 160 (48.8) Boom Length (51.8) 1 (54.9) 190 (57.9) 200 (61.0) 30 (9.1) 51.3 (23.3) 50.5 (22.9) 35 (10.7) 41.4 (18.8) 41.2 (18.7) 41.1 (18.6) 37.6 (17.1) 36.6 (16.6) 34.5 (15.6) 34.3 (15.6) 34.2 (15.5) 33.9 (15.4) 33.9 (15.4) 31.1 (14.1) 27.5 (12.5) 50 (15.2) 25.5 (11.6) 25.3 (11.5) 25.2 (11.4) 25.0 (11.3) 24.8 (11.2) 24.6 (11.2) 23.9 (10.8) 60 (18.3) 19.9 (9.0) 19.7 (8.9) 19.5 (8.8) 19.3 (8.8) 19.2 (8.7) 19.0 (8.6) 18.8 (8.5) 70 (21.3) 16.0 (7.3) 15.9 (7.2) 15.7 (7.1) 15.5 (7.0) 15.3 (6.9) 15.2 (6.9) 15.0 (6.8) (24.4) 13.2 (6.0) 13.1 (5.9) 12.9 (5.9) 12.7 (5.8) 12.5 (5.7) 12.4 (5.6) 12.2 (5.5) 90 (27.4) 11.1 (5.0) 10.9 (4.9) 10.8 (4.9) 10.6 (4.8) 10.4 (4.7) 10.2 (4.6) 10.0 (4.5) 9.4 (4.3) 9.3 (4.2) 9.1 (4.1) 8.9 (4.0) 8.7 (3.9) 8.6 (3.9) 8.4 (3.8) 110 (33.5) 8.1 (3.7) 7.9 (3.6) 7.7 (3.5) 7.6 (3.4) 7.4 (3.4) 7.2 (3.3) 7.0 (3.2) 120 (36.6) 7.0 (3.2) 6.8 (3.1) 6.6 (3.0) 6.5 (2.9) 6.3 (2.9) 6.1 (2.8) 5.9 (2.7) 130 (39.6) 6.0 (2.7) 5.9 (2.7) 5.7 (2.6) 5.5 (2.5) 5.3 (2.4) 5.2 (2.4) 5.0 (2.3) 1 (42.7) 5.1 (2.3) 4.9 (2.2) 4.7 (2.1) 4.5 (2.0) 4.4 (2.0) 4.2 (1.9) 150 (45.7) 4.2 (1.9) 4.0 (1.8) 3.9 (1.8) 3.7 (1.7) 3.5 (1.6) 160 (48.8) 3.4 (1.5) 3.3 (1.5) 3.1 (1.4) 2.9 (1.3) 170 (51.8) 2.7 (1.2) 2.6 (1.2) 2.4 (1.1) 1 (54.9) 2.1 (1.0) 1.9 (0.9) 190 (57.9) 1.5 (0.7) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. 138 HSL Link-Belt Cranes

27 Angle Boom Make---up 23 Boom Angle Boom Extensions Length 10 (3.05) 20 (6.10) 30 (9.14) (12.19) 50 (15.24) 1 60 (18.29) 1 70 (21.33) 1 (24.38) (27.43) 1 1 (30.48) (33.53) (36.58) (39.62) (42.67) (45.72) Notes: 3. Capacities shown are in kips/metric tons (1 kip = 1,000 lb / 1 metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. A deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, load weighing device, etc. When using main hook while jib or tip extension is attached, reduce capacities by values shown in Crane Rating Manual. See Operator s Manual for all limitations when raising or lowering attachment. 4. The capacities in the shaded areas are based on structural strength. The capacities in the non---shaded areas are based on stability ratings. 5. For recommended reeving, parts of line,wire rope type, and wire rope inspection, see Wire Rope Capacity Chart, Operator s Manual, and Parts Manual. 6. ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 7. The 22 ft (6.71m) live mast must be used for all capacities listed. 8. The least stable rated condition is over the side. 9. Booms must be erected and lowered over the end for maximum stability. 10. Main boom length must not exceed 150 ft (45.72m). Link-Belt Cranes 138 HSL

28 P8 Angle Boom Working Range Diagram Angle Boom Maximum Boom Angle SeeNote2. Main Boom Length Height Above Ground 30 Minimum Boom Angle SeeNote LC ofrotation Operating from Centerline of Rotation Notes: 1. Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length HSL Link-Belt Cranes

29 Angle Boom Chart (3.4) 12 (3.7) 13 (4.0) 14 (4.3) 15 (4.6) 16 (4.9) 17 (5.2) 18 (5.5) 19 (5.8) 20 (6.1) 25 (7.6) 30 (9.1) 35 (10.7) 50 (15.2) 60 (18.3) 70 (21.3) (24.4) 90 (27.4) 110 (33.5) 120 (36.6) 130 (39.6) 1 (42.7) (72.6) (72.6) (68.6) (64.0) (59.9) (56.3) (53.1) (50.2) (45.9) 93.3 (42.3) 66.5 (30.2) 51.3 (23.3) 41.6 (18.9) 34.7 (15.7) Angle Boom Lift Capacity Chart _ Rotation ABC = 52,320 lb (23 732kg) Counterweight -- Side Frames Extended [All capacities are listed in kips (mt)] 50 (15.2) (64.6) (62.6) (60.2) (58.7) (56.2) (53.0) (50.2) (46.0) 93.4 (42.4) 66.6 (30.2) 51.4 (23.3) 41.6 (18.9) 34.8 (15.8) 25.8 (11.7) 60 (18.3) (55.2) (53.8) (52.8) (51.5) (49.5) (46.0) 93.5 (42.4) 66.6 (30.2) 51.4 (23.3) 41.6 (18.9) 34.7 (15.7) 25.8 (11.7) 20.3 (9.2) 70 (21.3) (47.9) (46.7) (45.8) 98.5 (44.7) 93.4 (42.4) 66.6 (30.2) 51.3 (23.3) 41.5 (18.8) 34.6 (15.7) 25.7 (11.7) 20.1 (9.1) 16.5 (7.5) (24.4) 93.7 (42.5) 92.0 (41.7) 88.5 (.1) 66.5 (30.2) 51.2 (23.2) 41.3 (18.7) 34.5 (15.6) 25.5 (11.6) 19.9 (9.0) 16.1 (7.3) Boom Length (27.4) 84.3 (38.2) 82.7 (37.5) 66.3 (30.1) 51.0 (23.1) 41.2 (18.7) 34.3 (15.6) 25.3 (11.5) 19.7 (8.9) 15.9 (7.2) 13.1 (5.9) 66.2 (30.0) 50.9 (23.1) 41.0 (18.6) 34.1 (15.5) 25.1 (11.4) 19.5 (8.8) 15.7 (7.1) 12.9 (5.9) 10.8 (4.9) 110 (33.5) 65.3 (29.6) 50.7 (23.0).8 (18.5) 33.9 (15.4) 24.9 (11.3) 19.3 (8.8) 15.5 (7.0) 12.7 (5.8) 10.6 (4.8) 8.9 (4.0) 120 (36.6) 61.1 (27.7) 50.5 (22.9).6 (18.4) 33.7 (15.3) 24.7 (11.2) 19.1 (8.7) 15.3 (6.9) 12.5 (5.7) 10.3 (4.7) 8.7 (3.9) 7.3 (3.3) 130 (39.6) 50.3 (22.8).4 (18.3) 33.5 (15.2) 24.5 (11.1) 18.9 (8.6) 15.0 (6.8) 12.2 (5.5) 10.1 (4.6) 8.4 (3.8) 7.1 (3.2) 6.0 (2.7) 1 (42.7) 49.3 (22.4).2 (18.2) 33.3 (15.1) 24.3 (11.0) 18.6 (8.4) 14.8 (6.7) 12.0 (5.4) 9.9 (4.5) 8.2 (3.7) 6.8 (3.1) 5.7 (2.6) 4.8 (2.2) 150 (45.7) 44.6 (20.2) 39.9 (18.1) 33.1 (15.0) 24.0 (10.9) 18.4 (8.3) 14.5 (6.6) 11.7 (5.3) 9.6 (4.4) 7.9 (3.6) 6.6 (3.0) 5.5 (2.5) 4.5 (2.0) 3.7 (1.7) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. Link-Belt Cranes 138 HSL

30 P8 Jib Attachment Make---up Jib Length Jib Extensions Basic Frontstay Pendants Required Pairs Of Frontstay Extension Pendants Required 15 ft (4.57 m) 63 ft 5 in (19.33m) 14 ft 6 in (4.42m) 30 (9.15) 1 45 (13.72) (18.29) Notes: 1. Capacities shown are in kips/metric tons (1 kip = 1,000 lb / 1 metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on a firm supporting surface. 2. A deduction must be made from these capacities for the weight of the main boom hook block or hook ball, jib hook block or hook ball, slings, grapples, load weighing devices, etc. When using main hook while jib is attached, reduce capacities by values shown in Crane Rating Manual. See Operator s Manual for all limitations when raising or lowering attachment. 3. The capacities in the shaded areas are based on structural strength. The capacities in the non---shaded areas are based on stability ratings. 4. ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 5. These capacities are for ABC counterweight. 6. These capacities are for 360 working areas. 7. These capacities are for ft ( m) jib lengths only. 8. The jib cannot be used on tube boom lengths over 1 ft (54.86m) and angle boom lengths over 150 ft (45.7m). 9. The least stable rated condition is over the side. 10. These capacities are in compliance with ASME/ANSI B30.5 at date of manufacture. 11. These capacities apply only to the crane as originally manufactured and normally equipped by Link-Belt Construction Equipment Company. 138 HSL Link-Belt Cranes

31 Tube Boom + Jib Working Range Diagram 27 Maximum Boom Angle SeeNote2. Jib Length Main Boom Length Tube Boom Jib LC ofrotation Operating from Centerline of Rotation 60 Notes: 1. Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length Minimum Boom Angle SeeNote Height Above Ground Link-Belt Cranes 138 HSL

32 P8 Tube Boom + Jib Charts Tube Boom + 30 ft (9.14m) Offset Jib Length _ Rotation ABC [52,320 lb (23,732kg)] Counterweight [All capacities are listed in kips (mt)] 5 Offset 15 Offset 25 Offset Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (6.1) (10.9) (6.1) (6.1) (7.6) (10.9) (7.6) (10.9) (7.6) (9.1) (10.9) (10.9) (10.9) (9.1) (10.9) (9.1) (9.0) (10.7) (10.9) (10.9) (10.9) (10.7) (10.8) (10.9) (10.9) (10.7) (8.1) (9.3) (10.9) (10.9) (10.9) (10.9) (9.6) (10.9) (10.9) (7.7) (8.7) (9.2) (15.2) (9.6) (10.9) (10.9) (10.9) (8.2) (15.2) (7.9) (10.5) (10.9) (10.9) (7.8) (15.2) (6.7) (7.8) (8.2) (8.9) (18.3) (7.9) (9.4) (9.3) (8.9) (7.9) (18.9) (7.4) (9.5) (9.4) (9.1) (7.4) (18.9) (6.0) (7.3) (7.8) (8.2) (6.6) (21.3) (7.7) (7.5) (7.2) (6.8) (21.3) (7.8) (7.6) (7.3) (7.0) (21.3) (6.7) (7.2) (7.4) (6.4) (24.4) (6.4) (6.2) (5.9) (5.6) (24.8) (6.4) (6.3) (6.0) (5.7) (24.8) (6.3) (6.4) (6.1) (5.8) (27.4) (5.4) (5.3) (4.9) (4.6) (27.4) (5.5) (5.4) (5.0) (4.7) (27.4) (5.4) (5.1) (4.8) (4.7) (4.5) (4.2) (3.8) (4.7) (4.6) (4.3) (3.9) (4.6) (4.3) (4.0) (33.5) (3.9) (3.5) (3.2) (33.5) (3.9) (3.6) (3.3) (33.5) (3.7) (3.4) (36.6) (3.4) (3.0) (2.7) (36.6) (3.1) (2.8) (36.6) (3.1) (2.9) (39.6) (2.6) (2.3) (39.6) (2.7) (2.4) (39.6) (2.7) (2.4) (42.7) (2.3) (1.9) (42.7) (2.3) (2.0) (4267) (2.0) (45.7) (2.0) (1.6) (45.7) (2.0) (1.6) (45.7) (1.7) (48.8) (1.7) (1.3) (48.8) (1.4) (4887) (1.4) (51.8) (1.1) (51.8) (1.1) (51.8) (54.9) (0.9) (54.9) (0.9) (54.9) (57.9) (57.9) (57.9) (24.3) 1 (42.7) 1 (54.9) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. 138 HSL Link-Belt Cranes

33 29 Tube Boom + 45 ft (13.7m) Offset Jib Length _ Rotation ABC [52,320 lb (23,732kg)] Counterweight [All capacities are listed in kips (mt)] 5 Offset 15 Offset 25 Offset Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (7.6) (10.9) (7.6) (7.6) (9.1) (10.9) (10.9) (9.1) (8.7) (9.1) (10.7) (9.9) (10.9) (10.9) (10.7) (7.8) (10.7) (8.7) (10.9) (10.9) (10.9) (7.6) (8.3) (5.7) (15.2) (7.6) (9.4) (10.4) (10.1) (7.2) (15.2) (6.2) (7.8) (7.8) (8.3) (15.2) (4.8) (5.6) (5.9) (18.3) (6.2) (7.9) (8.9) (8.8) (6.9) (18.9) (5.2) (6.7) (7.3) (7.8) (6.3) (18.9) (4.2) (5.0) (5.3) (5.7) (21.3) (5.3) (7.5) (7.6) (7.3) (6.6) (21.3) (4.5) (5.9) (6.5) (7.2) (6.0) (21.3) (3.7) (4.5) (4.8) (5.3) (5.1) (24.4) (4.6) (6.4) (6.3) (5.9) (5.6) (24.8) (5.3) (5.9) (6.1) (5.8) (24.8) (4.1) (4.4) (4.9) (4.9) (27.4) (5.5) (5.3) (5.0) (4.6) (27.4) (4.8) (5.3) (5.1) (4.8) (27.4) (3.9) (4.1) (4.6) (4.8) (4.8) (4.6) (4.2) (3.9) (4.4) (4.6) (4.4) (4.0) (3.6) (3.9) (4.3) (4.2) (33.5) (4.1) (3.9) (3.6) (3.3) (33.5) (4.1) (4.0) (3.7) (3.4) (33.5) (3.7) (3.8) (3.5) (36.6) (3.6) (3.4) (3.1) (2.7) (36.6) (3.5) (3.2) (2.9) (36.6) (3.3) (2.9) (39.6) (3.0) (2.7) (2.3) (39.6) (3.1) (2.8) (2.4) (39.6) (2.8) (2.5) (42.7) (2.3) (2.0) (42.7) (2.4) (2.0) (4267) (2.4) (2.1) (45.7) (2.0) (1.6) (45.7) (2.0) (1.7) (45.7) (2.1) (1.8) (48.8) (1.7) (1.4) (48.8) (1.8) (1.5) (4887) (1.5) (51.8) (1.5) (1.1) (51.8) (1.2) (51.8) (1.2) (54.9) (0.9) (54.9) (1.0) (54.9) (57.9) (0.7) (57.9) (0.8) (57.9) (24.3) 1 (42.7) 1 (54.9) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. Link-Belt Cranes 138 HSL

34 P8 Tube Boom + 60 ft (18.3m) Offset Jib Length _ Rotation ABC [52,320 lb (23,732kg)] Counterweight [All capacities are listed in kips (mt)] 5 Offset 15 Offset 25 Offset Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (24.3) 1 (42.7) 1 (54.9) Main Boom Length (9.1) (9.6) (9.1) (9.1) (10.7) (8.3) (10.4) (10.7) (10.7) (7.8) (9.3) (10.1) (6.3) (15.2) (6.3) (7.8) (8.3) (8.6) (15.2) (5.1) (6.1) (6.5) (15.2) (3.9) (18.3) (5.1) (6.9) (7.8) (7.8) (6.1) (18.9) (4.3) (5.3) (5.6) (6.3) (18.9) (3.4) (3.8) (4.0) (21.3) (4.4) (5.9) (6.7) (6.9) (5.9) (21.3) (3.7) (4.6) (5.0) (5.6) (5.1) (21.3) (2.9) (3.4) (3.6) (3.9) (4.0) (24.4) (3.8) (5.1) (5.8) (6.0) (5.6) (24.8) (3.2) (4.1) (4.4) (5.1) (4.9) (24.8) (2.6) (3.1) (3.3) (3.6) (3.9) (27.4) (3.3) (4.5) (5.1) (5.0) (4.7) (27.4) (2.9) (3.7) (4.0) (4.7) (4.6) (27.4) (2.9) (3.0) (3.4) (3.6) (4.1) (4.6) (4.3) (3.9) (3.4) (3.7) (4.3) (4.1) (2.7) (2.9) (3.1) (3.4) (33.5) (3.7) (4.0) (3.6) (3.3) (33.5) (3.1) (3.4) (3.8) (3.4) (33.5) (2.5) (2.7) (2.9) (3.2) (36.6) (3.4) (3.5) (3.1) (2.8) (36.6) (2.9) (3.2) (3.2) (2.9) (36.6) (2.5) (2.8) (3.0) (39.6) (3.1) (3.0) (2.7) (2.4) (39.6) (2.9) (2.8) (2.5) (39.6) (2.4) (2.6) (2.6) (42.7) (2.7) (2.4) (2.0) (42.7) (2.8) (2.4) (2.1) (4267) (2.5) (2.2) (45.7) (2.4) (2.0) (1.7) (45.7) (2.1) (1.8) (45.7) (2.2) (1.9) (48.8) (1.8) (1.4) (48.8) (1.8) (1.5) (4887) (1.9) (1.6) (51.8) (1.5) (1.2) (51.8) (1.6) (1.2) (51.8) (1.3) (54.9) (1.3) (1.0) (54.9) (1.4) (1.0) (54.9) (1.1) (57.9) (0.8) (57.9) (0.8) (57.9) (24.3) 1 (42.7) 1 (54.9) This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. 138 HSL Link-Belt Cranes

35 Angle Boom + Jib Working Range Diagram 31 Notes: Maximum Boom Angle SeeNote2. Main Boom Length Jib Length Angle Boom Jib LC ofrotation Operating from Centerline of Rotation 1. Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. 2. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length Minimum Boom Angle SeeNote Height Above Ground Link-Belt Cranes 138 HSL