65-ton (60.0 mt) Rough Terrain Crane

Transcription

1 65-ton (60.0 mt) Rough Terrain Crane 65 tons (60.0 mt) at 9 ft (2.50 m) radius ft ( m) four section, full power boom with quick reeve boom head Boom wear pads have Teflon pucks that lubricate the boom sections (no grease) Two boom extend modes A-max and standard boom lifting capacities ft ( m) two piece, on-board lattice fly with 2, 15, 30, and 45 offsets One 16 ft (4.9 m) lattice insert plus 58 ft (17.7 m) two-piece offsettable fly option Two 16 ft (4.9 m) lattice inserts plus 58 ft (17.7 m) two-piece offsettable fly option No deducts for stowed attachments 211 ft 7 in (64.5 m) maximum tip height 17,182 lbs ( kg) maximum winch line pull 459 fpm (139.9 m/min) maximum winch line speed Next generation operator s cab with improved visibility and ergonomics 225 hp (168kW) Caterpillar engine with 644 ft-lbs (873J) of torque Spicer 6-speed power shift transmission 4x2 and 4x4 drive with 26.5x25-26PR tires Four steering modes: independent front, combination, crab, and independent rear 4 link rear suspension with optional hydro-gas suspension Travel/working weight under 90,000 lbs ( kg)

2 65-ton (60.0 mt) Rough Terrain Crane Remarkable control, reliability and capacity performance Caterpillar 3126B electronic engine with 225 hp (168 kw) provides 646 lb-ft (876 Nm) of torque Electronic throttle for improved throttle response Two automotive-style batteries linked in parallel and provide 700 cold cranking amps each for cold weather starting Rugged, lightweight steel pontoons Hydraulic disc brakes for both service brakes and parking brake Metri-Pak wire harnesses have sealed relays and connectors throughout for outstanding long-term reliability. All wires have flame retardant polyethylene insulation, resulting in a higher heat resistant wiring system. 4-section full power boom with attachment flexibility Full power 38 ft to 115 ft (11.6 m to 35.0 m) four-section boom with two extend modes: A-max and fully synchronized Boom wear pads have Teflon pucks that lubricate the boom sections (no grease) Maximum tip height is 211 ft 7 in (64.5 m) with the attachment and main boom used in combination Optional 35 ft (10.7 m) one-piece lattice fly and optional 35 ft to 58 ft (10.7 m to 17.7 m) twopiece bi-fold lattice fly are offsettable to 2, 15, 30 and 45. Optional 16 ft (4.9 m) lattice insert used alone or with 58 ft (17.7 m) two-piece offsettable fly Optional two 16 ft (4.9 m) lattice inserts plus 58 ft (17.7 m) two-piece offsettable fly Operator cab features Powerful hydraulics Extra large front window almost seamlessly merges into the roof window Sliding left side door, right and rear windows, and swing up top window provide excellent ventilation All gauges, switches, indicators, and controls are placed in the operator s forward line of sight for excellent ergonomics All gauges and switches are backlit for excellent visibility when the cab working lights are switched to the on position Integral rated capacity limiter aids operator in safe and efficient operation by continuously monitoring boom length, boom angle, head height, radius of load, machine configuration, allowed load, and percent of allowed load. Available Integrated air conditioning utilizes the same ventilation outlets as the standard heating system For greater productivity and control, the four-pump hydraulic circuit allows simultaneous function of boom hoist, winch and swing. Piston motor hydraulic hoist system delivers superior hoisting. Matched sizes of main and auxiliary winches provide equal maximum available line pulls of 17,182 lbs ( kg) and maximum line speeds of 459 fpm (140 m/min) on 13" (33 cm) root diameter drums. Job site maneuverability CALC Outrigger beams have three different stages (retracted, intermediate, and fully extended) providing lifting capacities in confined areas. Steering modes are chosen and performed with the steering wheel and include independent front steer, independent rear, four wheel steer, and "crab" steering. Link-Belt Construction Equipment Company - Lexington, Kentucky Link-Belt is a registered trademark. Copyright All rights reserved. We reserve the right to change designs and specifications at any time. Litho in U.S.A. 11/ #4317

3 5453 (supersedes 5429) J9 1 Technical Data Specifications & Capacities Telescopic Boom Rough Terrain Crane 65 ton (60.0 metric ton) CAUTION: This material is supplied for reference use only. Operator must refer to in--- cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures.

4

5 Table Of Contents Boom, Attachments, and Upper Structure... 1 Boom... 1 Boom Head... 1 Boom Elevation... 1 Auxiliary Lifting Sheave --- Optional... 1 Hook Blocks and Balls --- Optional... 1 Fly --- Optional... 1 Fly Inserts --- Optional... 1 Operator s Cab and Controls... 1 Swing... 2 Electrical... 2 Load Hoist System... 3 Load Hoist Performance M Main and Optional Auxiliary Winches... 3 Hydraulic System... 3 Counterweight... 3 Carrier... 4 General... 4 Outriggers... 4 Steering and Axles... 4 Suspension... 4 Tires and Wheels... 4 Brakes... 4 Electrical... 4 Engine... 4 Transmission... 4 Carrier Speeds and Gradeability... 5 Fuel Tank... 5 Hydraulic System... 5 Pump Drive... 5 Axle Loads... 6 General Dimensions... 7 Working Range Diagram... 8 Boom Extend Modes... 9 Main Boom Lift Capacity Charts -- Standard Fully Extended Outriggers Rotation On Tires --- Stationary --- Boom Centered Over Front Between Tire Tracks On Tires --- Pick & Carry (Creep) --- Boom Centered Over Front On Tires --- Stationary Rotation Fly Attachment Lift Capacity Charts -- Optional Fully Extended Outriggers Rotation ft Main Boom Length Fly Offset ft Main Boom Length Fly Offset ft Main Boom Length Fly Offset ft Main Boom Length Fly Offset... 14

6 Main Boom Lift Capacity Charts -- Metric Fully Extended Outriggers Rotation On Tires --- Stationary --- Boom Centered Over Front Between Tire Tracks On Tires --- Pick & Carry (Creep) --- Boom Centered Over Front On Tires --- Stationary Rotation Fly Attachment Lift Capacity Charts -- Optional Fully Extended Outriggers Rotation m Main Boom Length Fly Offset m Main Boom Length Fly Offset m Main Boom Length Fly Offset m Main Boom Length Fly Offset... 19

7 1 Boom, Attachments, and Upper Structure J Boom Design --- Four section, formed construction of extra high tensile steel consisting of one base section and three telescoping sections. The first telescoping section extends independently by means of one double---acting, single stage hydraulic cylinder with integrated holding valves. The second and third telescoping sections extend proportionally by means of one double---acting, single stage cylinder with integrated holding valves and cables. Boom S 38 ft ft ( m) four section full power boom S Two mode boom extension: A ---max mode provides superior capacities by extending the first telescoping section to 63 ft 8 in (19.4m). Standard mode synchronizes all the telescoping sections proportionally to 115 ft (35.0m). Controlled from the operator s cab. S Mechanical boom angle indicator S Maximum tip height for A ---max mode is 73 ft 6 in (22.4m) and standard mode is 123 ft 9 in (37.7m). Boom Head S Four 16.5 in (41.9cm) root diameter nylon sheaves to handle up to eight parts of line S Easily removable wire rope guards S Rope dead end lugs on each side of the boom head S Boom head is designed for quick---reeve of the hook block Boom Elevation S One double acting hydraulic cylinder with integral holding valve S Boom elevation: ---3 to 78 Auxiliary Lifting Sheave --- Optional S Single 16.5 in (41.9m) root diameter nylon sheave S Easily removable wire rope guards S Does not affect erection of the fly or use of the main head sheaves Hook Blocks and Balls --- Optional S 40 ton (36.3mt) 4 sheave quick---reeve hook block with safety latch S 60 ton (54.4mt) 4 sheave quick---reeve hook block with safety latch S 70 ton (63.5mt) 5 sheave quick---reeve hook block with safety latch S 8.5 ton (7.7mt) swivel and non---swivel hook balls with safety latch Fly --- Optional S 35 ft (10.7m) one piece lattice fly, stowable, offsettable to 2, 15, 30, and45. Maximum tip height is 158 ft (48.2m). S 35 ft---58 ft ( m) two piece bi---fold lattice fly, stowable, offsettable to 2, 15, 30, and 45. Maximum tip height is 180 ft 5 in (55.0m). Fly Inserts --- Optional S One 16 ft (4.9m) lattice insert, equipped with two 16.5 in (41.9cm) root diameter nylon sheaves, to be mounted between the boom head and fly options. Maximum tip height is 196 ft (59.7m). S Two16ft(4.9m) lattice inserts, one equipped with two 16.5 in (41.9cm) root diameter nylon sheaves, to be mounted between the boom head and fly options. Maximum tip height is 211 ft 7 in (64.5m). J Operator s Cab and Controls Environmental Cab --- Fully enclosed, one person cab of galvaneal steel structure with acoustical insulation Equipped with: S Tinted and tempered glass windows S Extra---large fixed front window with windshield wiper and washer S Swing up roof window with windshield wiper S Sliding left side door with large fixed window S Sliding rear and right side windows for ventilation S Six way adjustable, cushioned seat with seat belt and storage compartment S Engine dependent warm---water heater with air ducts for front windshield defroster and cab floor S Defroster fan for the front window S Bubble level S Circulating fan S Adjustable sun visor S Dome light S Cup holder S Fire extinguisher S Left side viewing mirror S Two position travel swing lock Air Conditioning --- Optional --- Integral with cab heating system utilizing the same ventilation outlets

8 2 Steering Column --- Pedestal type with tilt and telescope functions for operator comfort. Column includes the following controls and indicators: Left and right levers include: S Horn button S Turn signal switch S Driving light switch S Transmission direction switch Panel mounted switches for: S Travel park brake S Steer mode selector S 2/4 wheel drive/range selector S Transmission gear selector S Hazard flasher Panel mounted indicator/warning lights for: S Transmission temperature S Engine oil pressure S Travel park brake S Service brake S Turn signals S Rear wheel offset---optional S Emergency steer --- optional Armrest Controls --- Two dual axis hydraulic joystick controllers or optional single axis hydraulic controllers for: S Swing S Boom hoist S Main rear winch S Auxiliary front winch --- optional S Drum rotation indication S Drum rotation indicator activation switch S Winch high/low speed and disable switch(es) S Third wrap selector switch --- optional S Telescopic override switches S Warning horn button S Swing park brake Outrigger Controls --- Hand held control box with umbilical cord gives the operator the freedom to view operation while setting the outriggers. Foot Controls S Boom telescope S Swing brake S Engine throttle S Service brake Right Front Console --- Controls and indicators for: S Engine ignition S Console dimmer switch S Engine throttle lock S Bubble level S Function disable S 12 volt power connection S Front windshield wiper S Air conditioning --- optional and washer S Boom floodlight --- optional S Cab floodlights S Rotating beacon/strobe S Warning horn light --- optional S Heating controls S Third wrap indicator --- optional Cab Instrumentation --- Ergonomically positioned, analog instrumentation for crane operation including: S Engine coolant temperature with warning indicator S Hydraulic oil temperature with warning indicator S Fuel level with warning indicator S Tachometer S Transmission temperature with warning indicator S Voltmeter with warning indicator Rated Capacity Limiter --- Microguard graphic audio --- visual warning system integrated into the dash with anti--- two block and function limiter. Operating data available includes: S Crane configuration S Boom length and angle S Boom head height S Allowed load and % of allowed load S Boom angle S of load S Actual load S Operator settable alarms (include): S Maximum and minimum boom angles S Maximum tip height S Maximum boom length S Swing left/right positions S Operator defined area (imaginary plane) Internal RCL Light Bar --- Optional --- Visually informs the operator when crane is approaching maximum load capacity with a series of green, yellow, and red lights. External RCL Light Bar --- Optional --- Visually informs the ground crew when crane is approaching maximum load capacity with a series of green, yellow, and red lights. J Swing Motor/Planetary --- Bi---directional hydraulic swing motor mounted to a planetary reducer for 360 continuous smooth swing at 2.0 rpm Swing Park Brake , electric over hydraulic, (spring applied/hydraulic released) multi---disc brake mounted on the speed reducer. Operated by a switch from the operator s cab. Swing Brake , foot operated, hydraulic applied disc brake mounted to the speed reducer Swing Lock --- Two---position swing lock (boom over front or rear) operated from the operator s cab 360 Positive Swing Lock --- Optional --- Meets New York City requirement J Electrical Swing Alarm --- Audio warning device signals when the upper is swinging. Lights S Two working lights on front of the cab S One rotating amber beacon on top of the cab --- optional S One amber strobe beacon on top of the cab --- optional S Boom floodlight --- optional

9 3 J Load Hoist System Load Hoist Performance Main (Rear) and Auxiliary (Front) Winches --- 3/4in(19mm) Rope Maximum Line Pull Normal Line Speed High Line Speed Layer Total Layer lb kg ft/min m/min ft/min m/min ft m ft m 1 17, , , , , Maximum Diameter Wire Rope Application Type Permissible Load in mm lb kg Main (Rear) Standard 3/4 19 6x19 IWRC --- right regular lay (Type DB) 16, Winch Optional 3/ x19 rotation resistant --- right regular lay (Type RB) 12, Auxiliary (Front) Winch Standard 3/4 19 6x19 IWRC --- right regular lay (Type DB) 16, Optional 3/ x19 rotation resistant --- right regular lay (Type RB) 12, M Main and Optional Auxiliary Winches S Axial piston, full and half displacement (2---speed) motors driven through planetary reduction unit for positive control under all load conditions S Grooved lagging S Power up/down mode of operation S Drum rotation indicator(s) S Drum diameter: 13 in (33.0cm) S Rope length: S Front: 500 ft (152.4m) S Rear: 600 ft (182.9m) S Maximum rope storage: 657 ft (200.3m) S Terminator style socket and wedge S Hoist drum cable followers --- optional Third wrap indicator --- optional --- Visually and audibly warns the operator when the wire rope is on the first/bottom layer and when the wire rope is down to the last three wraps J Hydraulic System Counterbalance Valves --- All hoist motors, boom extend cylinders, and boom hoist cylinders are equipped with counterbalance valves to provide load lowering and prevents accidental load drop when hydraulic power is suddenly reduced. J Counterweight Total of 12,000 lb (5 443kg) of counterweight pinned to the upper structure frame with capacities for the 12,000 lb (5 443kg) configuration

10 4 Carrier J General S 10 ft 7 in (3.22m) wide S 14 ft 7 in (4.45m) wheelbase (centerline of first axle to centerline of second axle) Frame --- Box---type, torsion resistant, welded construction made of high tensile steel. Equipped with front and rear towing and tie---down lugs, tow connections, and access ladders. J Outriggers Boxes --- Two double box, front and rear welded to carrier frame Beams and Jacks --- Four single stage beams with Confined Area Lifting Capacities (CALCt) provide selectable outrigger extensions of full, intermediate, and retracted. Hydraulically controlled from the operator s cab with integral check valves. Pontoons --- Four lightweight, quick release, 23.5 x 23.5 in (59.7 x 59.7cm), steel pontoons with contact area of 460 in 2 (2 968cm 2 ) can be stored for road travel in storage racks on the carrier. Main Jack Reaction ,500 lb (41 050kg) forceand 197 psi (1 358kPa) ground bearing pressure J Steering and Axles Steering --- Four independent modes consisting of two wheel front, two wheel rear, four wheel, and crab. Each mode is controlled from the steering wheel and is selected by a switch in the operator s cab. Drive --- Two modes: 4 x 2 and 4 x 4 for off highway travel Axle Steered, non---driven for 4 x 2 and steered, driven for 4 x 4 Axle Steered, driven J Suspension Front --- Rigid mount to the carrier frame Rear --- The rear axle is suspended on the oscillation cylinders with motion of the axle controlled by a four bar linkage system. The oscillation cylinders lockout when the upper structure rotates 2.5 past centerline. S Hydro---gas rear suspension --- optional J Tires and Wheels Front and Rear --- Four (single) 26.5 x ply rating, earthmover type tires on steel disc wheels S Spare tires and wheels --- optional J Brakes Service --- Full hydraulic, dual circuit, disc type brakes on all wheel ends Parking/Emergency --- Spring applied type, acting on front axle J Electrical Two batteries provide 12 volt starting and operation Lights S Front lighting includes two main headlights and two parking/directional indicators. S Side lighting includes two parking/directional indicators per side. S Rear lighting includes two parking/directional indicators, two parking/brake lights, and two reversing lights. S Other equipment includes hazard/warning system, cab light, instrument panel light, and signal horn. J Engine Specification CAT 3126B Numbers of Cylinders 6 Cycle 4 Bore and Stroke: inch (mm) 4.33 x 5.00 (110 x 127) Piston Displacement: in 3 (L) 442 (7.2) Max. Brake Horsepower: hp (kw) Peak Torque: ft lb (J) 225 2,200 rpm 644 1,500 rpm Alternator: volts --- amps Crankcase Capacity: qt (L) 29.5 (27.9) S Mechanically driven fan and thermostatically controlled radiator J Transmission Powershift --- Three speed with high/low range for 6 forward and 6 reverse gears. Front axle disconnect for two or four wheel drive. Front axle disconnects in high range.

11 J Carrier Speeds and Gradeability Spicer Speed Gradeability stall) Gear Ratio mph km/h %Grade 6th Forward & th Reverse th 2WD/Hi rd Forward & nd Reverse st 4WD/Low Based on a gross vehicle weight of 88,000 lb (39 916kg). Crane operating angle must not exceed 35 (77% grade). J Fuel Tank One 75 gallon (283.9L) capacity tank J Hydraulic System All functions are hydraulically powered allowing positive precise control with independent or simultaneous operation of all functions. Main Pumps S One two section fixed displacement gear pump for the front/rear winches and boom hoist circuits. S One two section fixed displacement gear pump for the swing/telescope, power steering/outrigger/telescope, service brake, and oscillation circuits. S Combined pump capacity of 138 gpm (522.4Lpm) Hydraulic Reservoir gal (579.2L) capacity equipped with sight level gauge. Diffusers built in for deaeration. Filtration --- One 10 micron, full flow line filter in the control circuit. All oil is filtered prior to return to reservoir. Accessible for easy filter replacement. J Pump Drive All pumps are mounted on the transmission and mechanically driven by the diesel engine. S Front/rear winches and boom hoist pumps can be disconnected with a manual pump disconnect to aid in cold weather starting --- optional. 5

12 6 Axle Loads Gross Vehicle Upper Facing Front Upper Facing Rear Base crane with full tank of fuel Weight ( 1 ) Front Axles Rear Axles Front Axles Rear Axles lb kg lb kg lb kg lb kg lb kg 83, , , , , Pintle hook, front Pintle hook, rear Rear steer indicator Hydro---gas suspension Pump disconnect Operator in cab Hoist drum follower --- main Auxiliary winch with 500 ft (152.4m) wirerope Hoist drum follower --- auxiliary Substitute type DB rope with type RB rope --- main winch Substitute type DB rope with type RB rope --- auxiliary winch Substitute 500 ft (152.4m) wire rope with 600 ft (182.9m) auxiliary Remove 600 ft (182.9m) wirerope from rear (main) winch Remove 500 ft (152.4m) wirerope from front (auxiliary) winch Emergency steering mechanical swing lock Air conditioning Floodlight to front of boom base section Fly mounting brackets to boom base section for fly options ft (10.67m) offsettable fly --- stowed 1, , , ft ( m) offsettable fly --- stowed 2, , , , Auxiliary lifting sheave ton (54.4mt) 4---sheave hook block at bumper 1, , , ton (63.5mt) 5---sheave hook block at bumper 1, , , ton (7.7mt) hookballat bumper ton (54.4mt) 4---sheave hook block at boom head 1, , , , , ton (63.5mt) 5---sheave hook block at boom head 1, , , , , ton (7.7mt) hook ball at boom head Tire Maximum Allowable Axle 25 mph (40.2km/h) 26.5 x 25 (26---PR) 51,040 lb (23 151kg) ( 1 ) Adjust gross vehicle weight and axle loading according to component weight. Note: All weights are ±3%.

13 7 General Dimensions CofRotation L 38 0 (11.6m) 7 0 (2.1m) (1.7m) (0.3m) (2.0m) 12 2 (3.7m) 1 3 (0.4m) 7 8 (2.3m) 12 0 (3.7m) (4.1m) 6 11 (2.1m) 12 0 (3.7m) (4.1m) (0.8m) (13.9m) CofRotation L 10 2 (3.1m) Turning --- Front Wheel (4x2) Steering English Metric Wall to wall over carrier m Wall to wall over boom attachment m Curb to curb m Centerline of tire m Turning --- All Wheel (4x4) Steering English Metric Wall to wall over carrier m Wall to wall over boom attachment m Curb to curb m Centerline of tire m 23 (0.6m) Tail Swing English Metric With counterweight m Without counterweight N/A N/A (0.3m) 9.75 (0.2m) (2.5m) (2.9m) (3.2m) (5.4m) 24 0 (7.3m) Not To Scale

14 8 Working Range Diagram Height In Feet (Meters) Above Ground 220 (67.1) 210 (64.0) 200 (61.0) (3.0m) (57.9) 180 (54.9) 170 (51.8) 160 (48.8) 150 (45.7) 140 (42.7) 130 (39.6) 120 (36.6) 110 (33.5) 100 (30.5) 90 (27.4) 80 (24.4) 70 (21.3) 60 (18.3) 50 (15.2) 40 (12.2) 30 (9.1) 20 (6.1) 10 (3.0) (64.0) 8.5 (2.6m) 190 (57.9) 170 (51.8) 150 (45.7) 130 (39.6) 110 (33.5) 45 OFFSET 30 OFFSET 15 OFFSET 2 OFFSET (27.4) (21.3) (15.2) (9.1) (3.0) 115 (35.1m) + 90 (27.4m) 115 (35.1m) + 74 (22.6m) 115 (35.1m) + 58 (17.7m) 95 (29.0m) + 58 (17.7m) 115 (35.1m) + 35 (10.7m) 115 (35.1m) + 16 (4.9m) 95 (29.0m) + 35 (10.7m) 115 (35.1m) Mode B 105 (32.0m) 95 (29.0m) 85 (25.9m) 75 (22.9m) 65 (19.8m) 63.6 (19.4m) Mode A 55 (16.8m) 45 (13.7m) 38 (11.6m) Mode A & B 78 Max Boom Angle Boom + Fly Length In Feet (Meters) Boom Length In Feet (Meters) 200 (61.0) 180 (54.9) (48.8) (42.7) (36.6) (30.5) (24.4) (18.3) (12.2) Operating From Axis Of Rotation In Feet (Meters) 20 (6.1) Cof Rotation L

15 9 Boom Extend Modes Boom Mode A (A -max) Only inner mid section telescopes. Boom Length 38 (11.58m) 45 (13.72m) 55 (16.76m) Inner Mid Section 308 (7.82m) Stroke Base Section 63.6 (19.39m) Boom Mode B (Standard) Inner mid, outer mid, and tip sections telescope simultaneously. Boom Length 38 (11.58m) 45 (13.72m) 55 (16.76m) 65 (19.81m) 75 (22.86m) 85 (25.91m) 95 (28.96m) 105 (32.00m) Tip Section 308 (7.82m) Stroke Outer Mid Section 308 (7.82m) Stroke Inner Mid Section 308 (7.82m) Stroke Base Section 115 (35.05m)

16 10 Main Boom Lift Capacity Charts -- Standard (ft) Fully Extended Outriggers Rotation (All Capacities Are Listed In Pounds) Boom Length (ft) / , , , , , ,600 98,100 71,900** ,600 91,200 86,200 71,900** 54, ,100 66,800 66,400 66,100** 54,000 55,900 46, ,000 52,600 53,000 53,000 53,700 49,900 41,800 36,200 28, ,800 42,500 43,000 43,400 43,600 43,800 37,800 34,200 28, ,300 33,900 34,200 34,400 34,600 34,000 30,700 28, ,400 26,700 26,900 27,100 27,200 27,300 25, ,200 21,600 21,800 22,000 22,100 22,100 22, ,700 18,000 18,100 18,200 18,300 18, ,800 15,000 15,100 15,200 15,300 15, ,700 12,800 12,900 13,000 13, ,800 11,000 11,100 11,200 11, ,400 9,500 9,600 9, ,100 8,200 8,300 8, ,100 7,100 7, ,100 6,200 6, ,300 5, ,600 4, , , ** 63.6 A---max Mode (ft) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

17 11 (ft) On Tires -- Stationary -- Boom Centered Over Front Between Tire Tracks (All Capacities Are Listed In Pounds) Boom Length (ft) , ,800 56, ,500 48,900 39, ,400 39,100 39,500 30, ,000 29,700 30,100 30,400 22, ,600 21,400 21,900 22,200 22,400 17, ,000 16,600 16,900 17,100 17, ,900 13,300 13,400 13, ,200 10,600 10,800 11, ,500 8,800 8, ,800 7,100 7, ,700 5, ,600 4, , , (ft) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

18 12 (ft) On Tires -- Pick & Carry (Creep) -- Boom Centered Over Front (All Capacities Are Listed In Pounds) Boom Length (ft) , ,200 54, ,300 46,700 39, ,700 36,100 36,600 30, ,300 28,800 29,300 29,600 22, ,600 21,400 21,900 22,200 22,400 17, ,000 16,600 16,900 17,100 17, ,900 13,300 13,400 13, ,200 10,600 10,800 11, ,500 8,800 8, ,800 7,100 7, ,700 5, ,600 4, , , (ft) On Tires -- Stationary Rotation (All Capacities Are Listed In Pounds) Boom Length (ft) , ,000 39, ,800 27,400 27, ,200 16,800 17,300 17, ,500 11,100 11,700 12,000 12, ,800 7,500 8,100 8,400 8,600 8, ,000 5,600 5,900 6,200 6, ,800 4,100 4,400 4, ,400 2,800 3,000 3, ,700 1,900 2, ,100 1, (ft) (ft) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

19 13 Fly Attachment Lift Capacity Charts -- Optional (ft) 115 ft Main Boom Length 2 Fly Offset Fully Extended Outriggers Rotation (All Capacities Are Listed In Pounds) 115 ft Main Boom Length 15 Fly Offset Fly Length (ft) Fly Length (ft) (ft) , , ,100 8, , ,900 8,700 7, , ,600 8,400 7,200 5, , ,300 8,200 7,200 5, ,000 7, ,000 8,000 7,000 5, ,700 6,900 5, ,600 7,700 6,500 5, ,400 6,700 5,600 4, ,200 7,500 6,100 4, ,800 6,500 5,300 4, ,000 7,200 5,800 4, ,600 6,300 5,000 3, ,000 7,000 5,400 4, ,500 6,100 4,700 3, ,200 6,700 5,100 3, ,600 5,900 4,500 3, ,400 5,900 4,900 3, ,800 5,700 4,300 3, ,700 5,200 4,600 3, ,100 5,600 4,100 3, ,100 4,600 4,400 3, ,400 5,200 3,900 2, ,600 4,100 4,000 2, ,900 4,600 3,700 2, ,100 3,600 3,500 2, ,300 4,000 3,500 2, ,600 3,100 3,000 2, ,900 3,500 3,400 2, ,200 2,700 2,600 2, ,400 3,100 3,000 2, ,900 2,300 2,200 2, ,000 2,700 2,600 2, ,500 2,000 1,900 1, ,600 2,300 2,200 2, ,200 1,600 1,500 1, ,300 1,900 1,800 1, ,400 1,200 1, ,600 1,500 1, ,100 1, ,300 1,200 1, , This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

20 14 (ft) 115 ft Main Boom Length 30 Fly Offset Fully Extended Outriggers Rotation (All Capacities Are Listed In Pounds) 115 ft Main Boom Length 45 Fly Offset Fly Length (ft) Fly Length (ft) (ft) , , , , , , , ,200 5, , ,100 5,500 4, , ,000 5,300 4,000 3, ,400 4, ,000 5,200 3,800 3, ,300 4,800 3, ,200 5,100 3,700 2, ,400 4,700 3,300 2, ,400 5,000 3,500 2, ,600 4,700 3,200 2, ,700 4,900 3,400 2, ,900 4,700 3,100 2, ,100 4,900 3,200 2, ,200 4,600 3,000 2, ,500 4,500 3,100 2, ,600 4,600 2,900 2, ,000 3,900 3,000 2, ,200 2,800 2, ,500 3,400 2,900 2, ,700 2,700 1, ,100 3,000 2,800 1, ,200 2,700 1, ,500 2,500 1, ,700 2,600 1, ,200 2,200 1, ,200 2,300 1, ,800 1,800 1, ,900 1, ,400 1,400 1, ,600 1, ,100 1,100 1, , ,000 This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

21 15 Main Boom Lift Capacity Charts -- Metric (m) Fully Extended Outriggers Rotation (All Capacities Are Listed In Kilograms) Boom Length (m) / ** ** ** ** ** ** ** A---max Mode (m) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

22 16 (m) On Tires -- Stationary -- Boom Centered Over Front Between Tire Tracks (All Capacities Are Listed In Kilograms) Boom Length (m) (m) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

23 17 (m) On Tires -- Pick & Carry (Creep) -- Boom Centered Over Front (All Capacities Are Listed In Kilograms) Boom Length (m) (m) On Tires -- Stationary Rotation (All Capacities Are Listed In Kilograms) Boom Length (m) (m) (m) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

24 18 Fly Attachment Lift Capacity Charts -- Optional (m) m Main Boom Length 2 Fly Offset Fully Extended Outriggers Rotation (All Capacities Are Listed In Kilograms) m Main Boom Length 15 Fly Offset Fly Length (m) Fly Length (m) (m) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

25 19 (m) m Main Boom Length 30 Fly Offset Fully Extended Outriggers Rotation (All Capacities Are Listed In Kilograms) m Main Boom Length 45 Fly Offset Fly Length (m) Fly Length (m) (m) This information is not for crane operation. Operator must refer to the in--- cab information for crane operation. Rated lifting capacities shown on fully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

26 Link -Belt Construction Equipment Company Lexington, Kentucky RLink--Belt is a registered trademark. Copyright We are constantly improving our products and therefore reserve the right to change designs and specifications.