LS-208H II. HYLAB Series. Lattice Boom Crawler Crane 80-ton (77.62 mt)

Transcription

1 LS-208H II HYLB Series Lattice Crawler Crane 80-ton (77.62 mt) The duty cycle crane with big horsepower, outstanding versatility and bullet-proof hydraulic controls 80-ton (77.57 mt) at 11' (3.35 m) radius 190' (57.91 m) of tube boom or 160' + 60' (48.77 m m) boom plus jib combination 150' (45.72 m) of angle boom or 140' + 60' (42.67 m m) boom plus jib combination Maximum tip height is 223' (67.97 m) for tube boom or 203' (61.87 m) for angle boom Dual swing drives 43,400 lbs ( kg) maximum line pull 1" (25.4 mm) wire rope on front and rear hoist drums Large drum clutches and brakes 29,500 lbs ( kg) drag/clam/magnet capacity for angle boom

2 LS-208H II HYLB Series robust performer in Link-Belt s renowned HYLB (hydraulic lattice boom) family, the LS-208H II is built for ultimate versatility on the job site. Duty cycle requirements? The LS-208H II is the machine for the job The tube boom is ideally suited for lift crane work and combination lift/duty cycle requirements. The angle boom is a top notch performer in dragline, clamshell, pile driving and other severe duty cycle applications. Outfitting the angle boom with the optional live mast makes for fast assembly and disassembly. The LS-208H II can operate in automatic brake mode or with true gravity freefall operation. The boom top section features standard pin-on points for attachment of the jib, a 5' (1.52 m) tip extension or a universal pile driving lead adapter. 5' (1.52 m) auxiliary tip extension is available to improve clearance between the working hoist lines (9-ton (8.16 mt) capacity). Head machinery options include wide mouth drag sheaves or lift/clam sheaves. Pile driving lead adapter available Optional third drum with free spooling Big horsepower for 80-ton class crane 263 horsepower (196 kw) High horsepower for 80-ton class crane allows for high line speeds under high line pull conditions such as production duty cycle work including drag line/clamshell/dock/scrap and foundation demands. Extra capacity cooling beyond normal lift crane requirements to satisfy the higher horsepower and hydraulic flows the LS-208H II provides. Dual swing drives Dual swing motors and drive boxes on the LS-208H II ensure long swing life under the harshest demands. What you ve come to expect from a Link-Belt Fine Inching control for super precise handling Compact travel drives, hydraulic selfadjusting tracks and sealed idler and drive planetaries High travel torque Service after the sale When you invest in a Link-Belt crane, you also invest in a 125-year legacy of outstanding customer support. Link-Belt s customer service helps you maintain your investment over the long term, with the industry s most comprehensive crane product support available. Link-Belt crawler crane owners praise HYLB s low operating cost... the best in its class. Crane operations control center rmchair mounted, pilot-operated hydraulic controls n ergonomically designed to provide maximum comfort, control and load visibility Outstanding transportability The modular design of the LS-208H II transports in only three loads. Link-Belt s optional Quick Draw feature simplifies self-assembly, disassembly and load-out. Hydraulic cylinders in the boom base section pick up and handle the boom sections and counterweights. On the LS-208H II, you can remove counterweights, break down the boom, retract the sideframes, store the catwalks, pin the live mast and gantry, and be ready to load out in 2-3 hours. Link-Belt Construction Equipment Company Lexington, Kentucky Link-Belt is a registered trademark. Copyright ll rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications. Litho in US 9/00 #4246

3 H8 1 Technical Data Specifications & Tube Capacities LS -208H II Crawler Crane 80 Ton (72.57 metric ton) CUTION: This material is supplied for reference use only. Operator must refer to in--- cab Crane Rating Manual and Operator s Manual to determine allowable crane lifting capacities and assembly and operating procedures. Link-Belt Cranes LS---208HII

4 H8 LS---208HII Link-Belt Cranes

5 H8 1 Table Of Contents Pages Specifications 1--8 Tube Capacities Tube + Jib Capacities Link-Belt Cranes LS---208HII

6 H8 This page intentionally left blank LS---208HII Link-Belt Cranes

7 Specifications Lattice Crawler Crane LS 208H II 80 ton (72.57 metric ton) HYLB Series LS 208H II

8 LS 208H II Machine Transport Weights approximate LS 208H II

9 LS 208H II Transportation Weights approximate Base Machine: Rigid Backstops, 27 Gallons (102.2L) of Fuel, Catwalks (front and right side), 24 (7.3m) Live Mast, Bridle & Spreader Bar, 14 Part Hoist Reeving, 610 (186 m) of Type DB Front Hoist Rope, 540 (165m) of Type RB Rear Hoist Rope and uxiliary Lifting Bail. Gross Weight Item Description lb. kg. #1 Base Machine 92, Transport s #2 #3 Notes and Summary dd Counterweight 19, Numbers in the load columns to the left represent quantities. dd B Counterweight 20, dd Hydraulic Third Drum w/o rope 1, Estimated transport load dd 20 (6.1m) Tube Base Section 1, assumes the load out consist of dd 20 (6.1m) Tube Top Section 2, (45.7m) of angle boom + 60 (18.3m) of jib with full dd 10 (3.05m) Tubular Extension w/pins & pendants counterweight. dd 20 (6.1m) Tubular Extension w/pins & pendants dd 30 (9.1m) Tubular Extension w/pins & pendants 1, Support loads were targeted at dd 20 (6.1m) Base Section 2, ,000 lb (20 412kg), 8 6 (2.6m) wide, 48 (14.6m) long, dd 20 (6.1m) Top Section with 4 Lifting Sheaves 3, and 13 6 (4.1m) high using a dd 20 (6.1m) Top Section with 3 Lifting Sheaves 3, drop deck trailer. This may vary dd 20 (6.1m) Top Section with 2 Lifting Sheaves 3, depending on state laws, empty truck/trailer weights, and style dd 10 (3.05m) ngular Extension w/pins & pendants of trailer. dd 20 (6.1m) ngular Extension w/pins & pendants 1, dd 30 (9.1m) ngular Extension w/pins & pendants 2, Estimated weights vary by dd Bridle & Spreader Bar Only (No Live Mast) / 2%. dd Tagline Winder Estimated Total of #1 dd Fairleader ,094 lbs. (41 773kg). dd PT DS Estimated Total of #2 dd 30 (9.1m) Tubular Jib 1, ,641 lbs. (13 445kg). dd 15 (4.6m) Tubular Jib Extension dd 5 (1.5m) uxiliary Tip Extension Estimated Total of #3 dd Holding Rope 1 X 190 Type DB ,504 lbs (13 383kg). dd Closing Rope 1 X 240 Type DB dd Inhaul Rope 1 X 105 Type M dd Jib Wire Rope 1 X 700 Type DB 1, dd 3rd Drum Wire Rope 0.63 X 385 Type ZB dd 3rd Drum Wire Rope 0.63 X 385 Type WB dd uxiliary Lifting Bail dd 15 ton (13.6mt) Hook Ball Non Swivel dd 15 ton (13.6mt) Hook Ball Swivel dd 80 ton (72.6mt) 4 Sheave Hook Block 1, Remove Front Hoist Rope 1 X 610 Type DB 1, Remove Jib Wire Rope 1 X 540 Type RB 1, Remove 24 (7.3m) Live Mast with Bridle & Spreader Bar 2, dd 50 gallons (189.3L) of Fuel Machine Working Weight Option Description Gross Weight lbs. (kg) 1 Base Machine equipped with 40 (12.2m) of tubular boom, live mast, counterweight, 610 (186m) front hoist rope, 540 (164.6m) rear hoist rope, 80 ton (72.6mt) hook block, 77 gallons (291.4L) of fuel, and 200 lbs. (90.7kg) operator. 2 Option #1 plus B counterweight, midpoint pendants, and 150 (45.7m) of boom extensions to obtain 190 (57.91m) of main boom. 3 Option #2 plus 60 (18.3m) of jib and 15 ton (13.6mt) hookball subtract 20 (6.1m) of boom extension and midpoint pendants to obtain maximum ( m) of main boom + jib. 4 Base Machine equipped with 40 (12.2m) of angle boom, live mast, counterweight, 610 (186m) front hoist rope, 540 (165m) rear hoist rope, 80 ton (72.6mt) hook block, 77 gallons (291.4L) of fuel, and 200 lbs. (90.7kg) operator. 117,291 (53 202) 145,355 (65 932) 147,060 (66 705) 118,849 (53 909) 5 Option #4 plus B counterweight and 110 (33.5m) of boom extensions to obtain 150 (45.7m) of main boom. 147,719 (67 004) 6 Option #5 plus 60 (18.3m) of jib and 15 ton (13.6mt) hookball to obtain maximum ( m) of main boom + jib. Notes: 1. Ground bearing pressure is based on the total weight distributed evenly over the track contact area. 2. Total contact area for 36 (0.91m) track shoes is 15,689 in 2 (101,219cm 2 ). 150,787 (68 396) Ground Bearing Pressure psi (kg/cm 2 ) 7.48 (0.52) 9.26 (0.65) 9.37 (0.66) 7.58 (0.53) 9.42 (0.66) 9.61 (0.67) 3 LS 208H II

10 ttachment Options ( m) Tube Basic Tube 40 (12.2m) two piece design that utilizes a 20 (6.1m) base section and a 20 (6.1m) open throat top section with in line connecting pins on 54 (1.4m) wide and 44 (1.1m) deep centers. feet on 50 (1.3m) centers 3 (76.2mm) diameter chords Lugs on base section to attach carrying links Skywalk platform Deflector roller on top section Permanent skid pads mounted on top section to protect head machinery Rigid sheave guards Five 18 (0.5m) root diameter steel sheaves mounted on sealed anti friction bearings Mechanical boom angle indicator Tube Extensions Suggested Quantity for Max. 10 (3.05m) 1 20 (6.10m) 1 30 (9.14m) 4 Deflector roller on top of each section ppropriate length pendants Maximum tube boom tip height of 193 (58.8m) ( m) Basic 40 (12.2m) two piece design that utilizes a 20 (6.1m) base section and a 20 (6.1m) open throat top section with in line connecting pins. extensions are 48 (1.2m) wide and 48 (1.2m) deep at outside dimensions of angles. feet on 50 (1.3m) centers 4 X 4 X 0.38 (101.6 x 101.6x 9.5mm) angle chords Lugs on base section to attach carrying links Skywalk platform Deflector roller on top section Permanent skid pads mounted on top section to protect head machinery Rigid sheave guards Four 18 (0.5m) root diameter steel sheaves mounted on sealed anti friction bearings Mechanical boom angle indicator Extensions Suggested Quantity for Max. 10 (3.05m) 1 20 (6.10m) 2 30 (9.14m) 2 Deflector roller on top of each section ppropriate length pendants Maximum angle boom tip height of 154 (46.9m) ( m) Tube Jib Basic Tube Jib 30 (9.14m) two piece design that utilizes a 15 (4.6m) base section and a 15 (4.6m) top section with in line connecting pins on 32 (0.8m) wide and 24 (0.6m) deep centers. 2 (50.8mm) diameter tubular chords One 18.5 (0.46m) root diameter steel sheave mounted on sealed anti friction bearings. 15 (4.6m) jib extensions provide jib lengths at 45 (13.76m) and 60 (18.3m) Jib offset angles at 5, 15 and 25 degrees Maximum tip height of boom + jib is 233 (71.02m) using the tube boom and 214 (65.23m) using the angle boom uxiliary 5 (1.5m) Tip Extension Designed to use instead of a jib to provide clearance between working hoist lines. The extension is equipped with a single (0.4m) root diameter steel sheave mounted on sealed anti friction bearings. Maximum capacity is 9 ton (8.2mt). Hoist System Designed to lift off maximum boom or maximum boom plus jib unassisted. Operates up to a maximum boom angle of 82 degrees. utomatically limits maximum boom angle operation. Retractable gantry frame Pin on bail frame 14 part reeving with 5/8 (14.7mm) type C wire rope Bridle assembly 24 (7.3m) live mast (optional for angle attachment) Two 1.25 (31.8mm) pendants Tubular boom backstops (rigid type) Sheaves contain sealed anti friction bearings speed from is 52 seconds with no load and 94 seconds with full load. Speed was determined using 100 (30.5m) of tube boom LS 208H II

11 Revolving Upperstructure Frame ll welded steel frame with precision machined surfaces for mating parts. Engine Mitsubishi 6D24 TEB with oil cooler, air cleaner, fuel filter, water separator, hour meter, tachometer, and electrical shutdown. Number of cylinders 6 Bore and stroke in (mm) Piston displacement in 3 (cm 3 ) 5.12 x 5.91 (130 x 150) 729 (11945) Engine rpm at full load speed 2,000 Hi idle rpm 2,200 Full load speed horsepower (kw) 263 (196) Peak torque ft lb (joule) 746 (1011) Peak torque rpm 1,400 Electrical system Batteries 24 volt 2 12 volt Hydraulic System Specifications Hydraulic Pumps The pump arrangement is designed to provide hydraulically powered functions allowing positive, precise control with independent or simultaneous operation of all crane functions. Two variable displacement pumps operating at 4,000 psi (281kg/cm 2 ) and 64 gal/min (243L/min) powers load hoist drums, boom hoist drum, optional third drum, and travel. One fixed displacement gear type pump operating at 3,600 psi (250kg/cm 2 ) and 31 gal/min (117L/min) powers the swing and treadmember retract cylinders. One fixed diplacement gear type pump operating at 3,000 psi (210kg/cm 2 ) and 35 gal/min (130L/min) powers the swing motor. One fixed displacement gear type pump operating at 1,200 psi (84.4kg/ cm 2 ) and 10.5 gal/min (39.7L/min) powers the pilot control system, clutches, brakes and pump controls. Hoist Drums Each drum contains a pilot controlled, bi directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. Power up/down & free fall operation modes utomatic brake mode (spring applied, hydraulically released, band type brake) 1 (25.4mm) grooved lagging Drum pawl controlled manually Electronic drum rotation indicators Mounted on anti friction bearings (0.47m) root diameter (0.86m) flange diameter (0.52m) width Optional Front Mounted Third Hoist Drum The hydraulic winch is pinned to the front of the upper frame and is used in conjunction with a fleeting sheave and 3 sheave idler assembly to run the wire rope over the boom top section. Free spooling capability for pile driving applications (0.27m) root diameter 20 (0.51m) flange diameter 13.5 (0.34m) width Mounted on anti friction bearings Hoist Drum Contains a pilot controlled, bi directional, axial piston motor and a planetary gear reduction unit to provide positive control under all load conditions. Spring applied, hydraulically released, disc type brake controlled automatically 5/8 (15.88mm) grooved lagging Drum pawl controlled manually Mounted on anti friction bearings (0.27m) root diameter (0.60m) flange diameter (0.26m) width Swing System Mechanical linkage controls the dual bi directional axial piston motors and the planetary gear reduction unit to provide positive control under all load conditions. Spring applied, hydraulically released, 360 degree multi plate brake Free swing mode when lever is in neutral position Two position positive house lock udio/visual swing alarm Maximum swing speed is 3.0 rpm Upper Counterweight Consist of a two piece design that can be easily lowered to the ground using the gantry. 19,600 lbs. (8 890kg) upper counterweight 20,100 lbs. (9 117kg) B upper counterweight can be added to maximize capacities Operator s Cab and Controls Fully enclosed modular steel compartment is independently mounted and insulated to protect against vibration and noise. ll tinted/tempered safety glass Sliding entry door and front window Swing up roof window with wiper Door and window locks Heater with circulating fan ir conditioner Sun visor Engine instrumentation panel (tachometer, voltmeter, engine oil pressure, engine water temperature, fuel level, hydraulic oil temperature, and service monitor system) Electronic drum rotation indicators Six way adjustable seat with seat belt Dry chemical fire extinguisher Hand and foot throttle Fully adjustable single axis control levers Swing lever with swing brake and horn located on handle Bubble type level 5 (continued on page 7) LS 208H II

12 LS 208H II Hoisting Performance vailable line speed and line pull based on Mitsubishi 6D24 TEB at 2,000 rpm full load speed. Line pulls are not based on wire rope strength. See Wire Rope Capacity Chart for maximum permissible single part of line working loads. Rope Layer Front or Rear Drum 1 (25.4 mm) Wire Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 43, , , , , , , Rope Layer Hoist Drum 5/8 (15.9mm) Wire Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total lb kg ft/min m/min ft/min m/min in mm ft m ft m Rope Layer Front Mounted Third Drum 5/8 (15.9mm) Wire Rope Maximum Line Pull No Line Speed Full Line Speed Pitch Diameter Layer Total lb kg ft/min m/min ft/min m/min in mm ft m ft m 1 15, , , , , , Wire Rope pplication Diameter Length Type Maximum Permissible in mm ft m lb kg Hoist 5/ C 14, Front Hoist DB 29, Rear Hoist (Optional) RB 22, Rear Hoist (Optional) DB 29, Third Drum (Optional) 5/ ZB 11, Third Drum (Optional) 5/ WB 13, Rope Type Description DB 6 x 26 (6 X 19 Class) Warrington Seale Extra Improved Plow Steel Preformed Right Lay Regular Lay I.W.R.C. RB* 19 x 19 Rotation Resistant Extra Improved Plow Steel Preformed Right Lay Regular Lay Swaged SF=5.1 ZB 36 x 7 Non rotating Extra Improved Plow Steel Right Lay Regular Lay S.F.=5.1 WB 8 Strand Regular Lay C 9 x 40 Strand, Post Formed, Swaged Constructex Crush Resistant * Use of swivel ball is not recommended. LS 208H II

13 Revolving Upperstructure (continued from page 5) Indicator/ Rated Capacity Limiter Standard Equipment PT EI 65 load indicator provides two lineriders, angle sensor, computer, display, and anti two block equipment to provide the following information. length & angle Jib length & angle on hook radius Tip height nti two block warning & function limiters Operation mode Operator settable alarms provide audio/visual warning Provides an audio/visual warning when the load on hook is within 90% of the cranes rated load. Provides an audio/visual warning and limits functions when the load on hook is at 100% of the cranes rated load. dditional Equipment Standard 57.9 (1.5m) outside diameter turntable bearing Front, right, & left side removable catwalks 77 gal (291.5L) fuel tank (usable quantity) Machine lifting links dditional Equipment Optional Rud o matic model 1248 tagline winder for angle boom (double barrel, spring wound, drum type) Rud o matic model 648 tagline winder for tube boom Full revolving type Fairleader with barrel, sheaves, and guide rollers Lower Structure Lower Frame ll welded box construction frame with precision machined surfaces for turntable bearing and rotating joint (2.7m) overall width (3.6m) overall length Treadmembers ll welded, precision machined, steel frames can be hydraulically extended and retracted by a hydraulic cylinder mounted in the lower frame. 14 (4.3m) extended gauge 8 11 (2.7m) retracted gauge 20 2 (6.2m) overall length 36 (0.9m) wide track shoes 11 sealed (oil filled) track rollers per treadmember Sealed (oil filled) idler and drive sprockets Compact travel drives Hydraulic self adjusting tracks Individual control provides smooth, precise maneuverability including full counter rotation Spring applied, hydraulically released disc type brake controlled automatically Maximum travel speed is 1.0 mph (1.6km/h) in high speed and 0.6 mph (1km/h) in low speed Designed to 30% gradeability 7 LS 208H II

14 Link Belt Construction Equipment Company Lexington, Kentucky Link Belt is a registered trademark. Copyright We are constantly improving our products and therefore reserve the right to change designs and specifications. LS 208H II

15 Lifting Capacities Hydraulic Lattice Crawler Crane LS 208H II Tube Capacities ft. ( m) 80 ton (72.6 metric ton) 24 (7.31m) Live Mast Extended/Retracted 5 (1.52m) Tip Extension Duty Cycle Capacities ( m) Tube Extended Dragline with Counterweight Clamshell with Counterweight Tube Capacities ( m) Tube 54 (1.4 m) Wide x 44 (1.1 m) Deep 20 (6.10 m) Open Throat Top Section Extended / Retracted Blocked Capacities B,, or 0 Counterweight Options 20 2 (6.15 m) Crawler Length LS 208H II CUTION: This material is supplied for reference use only. Operator must refer to in cab Crane Rating Manual to determine allowable machine lifting capacities and operating procedures.

16 LS 208H OPERTING INSTRUCTIONS GENERL: 1. Rated lifting capacities in pounds as shown on lift charts pertain to this crane as originally manufactured and normally equipped. Modifications to the crane or use of optional equipment other than that specified can result in a reduction of capacity. 2. Construction equipment can be dangerous if improperly operated or maintained. Operation and maintenance of this crane must be in compliance with the information in the Operator s, Parts, and Safety Manuals supplied with this crane. If these manuals are missing, order replacements through the distributor. 3. The operator and other personnel associated with this crane shall read and fully understand the latest applicable merican National Standards Institute (NSI) safety standards for cranes. 4. ll capacities listed in this book are in compliance with SME/NSI B30.5. LIFT CRNE OPERTION: 1. Capacities shown are in pounds and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, etc. When using main hook while jib is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Hook With Jib Installed. When using main hook while 5 foot tip extension is attached, reduce capacities by values shown on Capacity Deductions For Lifting Off Main Hook With 5 foot Tip Extension Installed. See Operator s Manual for all limitations when raising or lowering attachment. 2. The crane capacities in the shaded areas are based on structural strength. The crane capacities in the non shaded areas are based on stability. 3. For recommended reeving, parts of line, wire rope type, and wire rope inspection, see Wire Rope Capacity chart, Operator s Manual, and Parts Manual. Rated lifting capacities are based on correct reeving. Deduction must be made for excessive reeving. ny reeving over minimum required (see Wire Rope Capacity Chart) is considered excessive and must be accounted for when making lifts. Use working range diagram to estimate the extra feet of rope then deduct 1.9 lb. for each extra foot of wire rope before attempting to lift a load. 4. ratings in this Crane Rating Manual are based on freely suspended loads and make no allowances for such factors as the effect of ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. 5. Rated lifting capacities do not account for the effects of wind on a suspended load or boom. Lifting capacities should be considered acceptable for wind speeds less than 20 mph and appropriately reduced for wind speeds greater than 20 mph. Extreme caution should be used when lifting heavy loads or loads with large wind sail area under high wind conditions (over 20 mph). 6. The capacities listed in this Crane Rating Manual are for the machine with live mast, with the gantry in the raised position. 7. The least stable rated condition is over the side. 8. s should be erected and lowered over the end for maximum stability. See Liftoff Capabilities before erecting or lowering boom. 9. Do not operate at radii and boom lengths where the Crane Rating Manual lists no capacity. Do not use longer booms or jibs than those listed in this Crane Rating Manual. ny of the above can cause a tipping condition, or boom and jib failure. 10. These capacities apply only to the crane as originally manufactured and normally equipped by Link Belt Construction Equipment Company. FOR OVER END BLOCKED CPCITIES ONLY 1. These capacities can be lifted over either end with the crane standing level on a firm supporting surface with adequate blocking placed under the tread member sprockets/idlers, to prevent rocking. 2. Do not travel with a load. TRVELING WITH LOD: 1. ll 360 Rotation Capacities listed in this Crane Rating Manual are pick and carry capacities. 2. The boom must be pointing straight over one end of the crawler lower. If the load was lifted over the side, swing the load over the end and/or if the load was lifted at a long radius and the load is at or near capacity for that radius, boom up to obtain a greater lifting capacity before beginning travel. 3. Engage the swing lock and apply swing brake. 4. Travel slowly and cautiously on a firm and level supporting surface. DEFINITIONS: 1. : Horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of the vertical hoist line or tackle with load applied. 2. : The angle between the boom base section and horizontal with freely suspended load at the rated radius. 3. Working rea: rea measured in a circular arc about the centerline of rotation as shown on the Working rea Diagram. 4. Freely Suspended : hanging free with no direct external force applied except by the hoist line. 5. Side : Horizontal side force applied to the lifted load either on the ground or in the air.

17 WIRE ROPE CPCITY 1 5/8 Parts of Type Type Type Type Type Line M DB RB ZB WB 1 29,500 29,500 22,700 * 11,000 13,600 * 2 59,000 59,000 45,500 22,000 27, ,500 88,500 68,100 33,000 40, , ,000 90,800 44,000 54, , , ,500 55,000 68, , , ,200 66,000 81, , , ,900 77,000 95, , , ,600 88, ,800 LBCE Type DB RB* ZB WB* M Description Notes Capacities shown are in pounds and working loads must not exceed the ratings on the capacity charts in this Crane Rating Manual. Study Operator s Manual for wire rope inspection procedures. 6 x 26 (6 x 19 Class) Warrington Seale Extra Improved Plow Steel Preformed Right Lay Regular Lay I.W.R.C. 19 x 19 Rotation Resistant Extra Extra Improved Plow Steel Preformed Right Lay Regular Lay. Swaged S.F. = 5:1 36 x 7 Class Non Rotating Extra Improved Plow Steel Right Lay Regular Lay S.F. = 5:1 8 Strand Regular Lay 6 X 19 Class Extra Improved Plow Steel Lang Lay * Use of swivel end with 1 part of line is not recommended. WORKING RES 360 LIFTOFF CPBILITIES / Over Side (Gantry In Raised Position) Counterweight () Maximum Maximum + Jib NO (RETRCTED) NO (EXTENDED) (RETRCTED) (EXTENDED) B (EXTENDED) See Note N/ 120 N/ 130 N/ 160 N/ See Note 4 1. For maximum stability, booms should be erected or lowered over the end with no load and with the hook block on the ground. 2. Crane on firm and level surface. 3. Gantry pins must be installed with the gantry in the raised position. 4. Liftoff over end only with 170 ft.+ 45 ft., 170 ft ft., 180 ft ft. and 180 ft ft. boom. For 170 ft ft., 170 ft ft., 180 ft ft. or 180 ft ft. (side frame extended) with B counterweight only, adequate blocking must be placed under both tread member sprockets (or idler rollers) at the end that the boom is to be lifted off to prevent rocking. The ramps supplied with the crane are consid ered to be adequate blocking. Over Side See Note Over Idler End Longitudinal Of Crawler Center Of Rotation Over Drive End Idler Sprocket See Note Drive Sprocket Over Side Note: These Lines Determine The Limiting Position Of ny For Operation Within Working reas Indicated. LS 208H

18 LIVE MST LIFTING CPCITIES (WITHOUT COUNTERWEIGHT INSTLLED) Live Mast Extended Retracted ,000 60, ,000 51, ,000 44, ,000 39, ,000 34, ,400 31, ,700 28, ,400 26, ,000 24, ,300 22, ,200 20, ,500 19, ,200 18, ,200 17, ,400 16,400 NOTES: 1. Refer to the Operator s Manual. 2. Live mast backstops must be in position and operative. 3. Use rear hoist drum only. Reeve hoist line to drum over live mast cross member. 4. Reeve hoist rope with three (3) parts of 1 diameter wire rope. 5. The crane shall be leveled on a firm supporting surface See Crane ssembly Component Weights chart for weight of compo nents for crane assembly. 8. Rated capacities for 360 rotation. 9. Gantry can be either in the raised or lowered position when liftin loads with the live mast. When the gantry is in the lowered position the back stay links must be pinned. Do not unpin the backstay links with the gantry in the lowered position, until the live mast is lowered and supported. 10. Do not lower live mast below 3 angle with gantry in lowered position. LS 208H

19 1. The capacities included in the Duty Cycle Capacities Tube chart are the maximum allowable, and are based on an LS 208H II crawler crane with a (19,800 lbs.) counterweight, stand ing level on firm suporting surface under ideal job conditions. 2. Capacities are based on 75% of minimum tipping loads for dragline, 67.5% for clamshell. 3. Capacities are maximum recommended by PCS Standard #4. Operator must make allowances for soft or uneven supporting sur faces, rapid cycle operations, bucket suction, or other unfavorable conditions which may require smaller buckets for most efficient operation. 4. Weight of bucket plus load, must not exceed these capacities. 5. Dragline operation is not recommended with boom angles less than length for dragline/clamshell attachment operation should not exceed 70 ft. 7. Retractable high gantry must be fixed in raised position for all capacities on the Duty Cycle Capacities Tube chart. 8. These capacities apply to the machine as originally manufactured and normally equipped by Link Belt Construction Equipment Company. Length Extended Counterweight (ll capacities listed are in pounds) Dragline Clamshell / Magnet , , , , , , , , , , , , ,800 15, ,800 15, ,800 15, , , , , , , , , , , , , ,800 15, ,800 15, ,800 15, ,900 Length Extended Counterweight (ll capacities listed are in pounds) Dragline Clamshell / Magnet , , , , , , , , , , , ,800 15, ,800 15, ,800 13, , , , , , , , , , , , ,800 15, ,500 13, ,900 10, ,400 LS 208H

20 WORKING RNGE DIGRM in feet above ground Minimum See Note Maximum See Note Main Length Operating radius from centerline of rotation in feet C L OF ROTTION LS 208H

21 CPCITY DEDUCTIONS FOR LIFTING OFF MIN BOOM HOOK WITH JIB INSTLLED When using main boom hook, while jib is attached, reduce boom capacities by the values in the following chart: Jib Length Capacity Deduction 30 2, , ,200 CPCITY DEDUCTIONS FOR LIFTING OFF MIN BOOM HOOK WITH 5 FOOT TIP EXTENSION INSTLLED MXIMUM LLOWBLE CPCITIES FOR 5 FOOT TIP EXTENSION LIFTING CPCITY TO BE THE SMLLEST OF THE FOLLOWING VLUES: 1. 18,000 lb (Maximum). 2 The standard crane lift capacity minus 1,100 lb for the boom length, tip extension load radius, and counterweight configura tion in use on the crane. NOTES: 1. ll notes are to be adhered to as listed on the standard lift crane capacity charts. 2. Reduce the main boom lift capacities by 1,100 lb when the tip extension is installed. 3. The maximum boom length on which the tip extension can be installed is 190 ft. 4. Do not lift or suspend a load from the boom tip extension and main boom at the same time. When using main boom hook, while 5 foot tip extension is attached, reduce boom capacities by the values in the following chart: Tip Extension Capacity Deduction 5 1,100 LS 208H

22 B (Ft.) MIN BOOM CPCITIES 40 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , , , , ,900 80, , , , , ,600 65, , , , ,500 90,700 55, , , , ,600 78,200 47, , , ,400 85,200 68,700 41, , , ,700 72,700 61,200 36, , ,400 96,600 63,300 55,100 33, , ,200 85,600 56,000 50,100 29, , ,200 76,800 50,100 45,800 27, ,000 96,300 69,600 45,300 42,200 25, ,600 88,100 63,500 41,300 39,100 23, ,700 81,100 58,400 37,900 36,400 21, ,400 57,800 41,400 26,500 26,700 15, ,100 44,500 31,700 20,100 20,800 11, ,300 36,000 25,400 15,900 16,900 9, ,800 30,000 21,000 12,900 14,000 7,400 (Ft.) MIN BOOM CPCITIES 70 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , , ,700 73,800 61,700 37, , ,500 97,500 64,200 55,500 33, , ,300 86,400 56,800 50,400 30, , ,900 77,500 50,800 46,100 27, ,600 96,900 70,200 45,900 42,500 25, ,200 88,600 64,100 41,900 39,300 23, ,300 81,600 59,000 38,400 36,600 21, ,900 58,100 41,700 26,900 26,900 15, ,500 44,800 32,000 20,300 21,000 11, ,600 36,200 25,700 16,100 17,000 9, ,200 30,200 21,300 13,200 14,100 7, ,600 22,400 15,500 9,300 10,200 5, ,800 17,500 11,900 6,900 7,700 3, ,800 14,100 9,400 5,200 6,000 2,400 (Ft.) MIN BOOM CPCITIES 50 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , , , ,400 91,100 55, , , , ,300 78,600 47, , , ,000 85,800 69,000 41, , , ,200 73,200 61,500 37, , ,300 97,000 63,800 55,400 33, , ,600 86,000 56,400 50,300 30, , ,500 77,200 50,500 46,000 27, ,000 96,600 69,900 45,700 42,400 25, ,600 88,400 63,900 41,600 39,300 23, ,600 81,400 58,700 38,200 36,500 21, ,700 58,000 41,600 26,800 26,900 15, ,300 44,700 31,900 20,300 21,000 11, ,500 36,200 25,600 16,100 17,000 9, ,100 30,200 21,200 13,100 14,100 7, ,500 22,300 15,500 9,200 10,200 5,100 MIN BOOM CPCITIES 80 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , ,100 97,600 64,400 55,500 33, , ,900 86,500 56,900 50,400 30, , ,900 77,600 50,900 46,100 27, ,300 97,000 70,300 46,000 42,500 25, ,000 88,700 64,100 41,900 39,300 23, ,100 81,600 59,000 38,400 36,600 21, ,900 58,100 41,700 26,900 26,800 15, ,400 44,700 31,900 20,300 20,900 11, ,600 36,200 25,600 16,100 16,900 9, ,100 30,200 21,200 13,100 14,000 7, ,600 22,300 15,500 9,200 10,200 5, ,700 17,400 11,900 6,800 7,700 3, ,700 14,100 9,400 5,100 5,900 2, ,800 11,600 7,500 3,900 4,600 1,500 (Ft.) LS 208H MIN BOOM CPCITIES 60 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , , , ,800 78,800 48, , , ,400 86,200 69,200 42, , , ,500 73,600 61,600 37, , ,100 97,300 64,100 55,500 33, , ,600 86,200 56,600 50,400 30, , ,800 77,400 50,700 46,100 27, ,800 96,800 70,100 45,800 42,500 25, ,400 88,500 64,000 41,800 39,300 23, ,500 81,500 58,900 38,300 36,600 21, ,800 58,100 41,700 26,900 26,900 15, ,400 44,800 32,000 20,300 21,000 11, ,600 36,200 25,700 16,100 17,000 9, ,200 30,200 21,300 13,200 14,200 7, ,600 22,400 15,500 9,300 10,300 5, ,700 17,500 11,900 6,800 7,800 3,600 MIN BOOM CPCITIES 90 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted , ,200 86,600 57,000 50,400 30, , ,500 77,600 51,000 46,100 27, ,000 97,000 70,300 46,000 42,400 25, ,100 88,700 64,200 41,900 39,200 23, ,800 81,600 59,000 38,400 36,500 21, ,900 58,000 41,700 26,800 26,700 15, ,400 44,700 31,900 20,200 20,800 11, ,500 36,100 25,500 16,000 16,800 9, ,000 30,100 21,100 13,000 13,900 7, ,500 22,200 15,400 9,100 10,000 4, ,600 17,300 11,800 6,700 7,600 3, ,700 14,000 9,300 5,000 5,800 2, ,800 11,500 7,500 3,800 4,500 1, ,600 9,600 6,100 2,800 3,500

23 B MIN BOOM CPCITIES 100 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation 0 Retracted ,200 92,200 70,300 46,000 42,300 25, ,800 88,700 64,100 41,900 39,200 23, ,400 81,600 59,000 38,400 36,400 21, ,900 58,000 41,600 26,800 26,600 15, ,300 44,600 31,800 20,100 20,700 11, ,400 36,000 25,400 15,900 16,700 9, ,900 30,000 21,000 12,900 13,800 7, ,400 22,100 15,200 9,000 9,900 4, ,500 17,200 11,600 6,600 7,400 3, ,500 13,900 9,200 4,900 5,700 2, ,700 11,400 7,400 3,700 4, ,500 9,500 6,000 2,700 3, ,800 8,000 4,900 2,000 2,600 MIN BOOM CPCITIES 130 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation ,100 57,700 41,400 26, ,100 44,300 31,500 20, ,100 35,600 25,100 16, ,600 29,600 20,600 13, ,000 21,700 14,800 9, ,100 16,800 11, ,100 13,400 8, ,300 11,000 6, ,100 9,100 5,600 PR ROH HIBIT ITED 7,000 5,200 3,900 3, ,400 7,700 4,500 2, ,000 6,500 3,600 1, ,900 5,500 2, ,900 4,600 2,200 Retracted 0 PR ROH HIBIT ITED MIN BOOM CPCITIES 110 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation ,800 57,900 41,500 26,700 26, ,300 44,500 31,700 20,000 20, ,300 35,900 25,300 15,800 16, ,800 29,800 20,900 12,800 13, ,300 22,000 15,100 8,900 9, ,400 17,100 11,500 6,400 7, ,400 13,700 9,000 4,800 5, ,500 11,300 7,200 3,600 4, ,400 9,400 5,900 2,600 3, ,700 7,900 4,800 1,900 2, ,300 6,700 3,900 1,800 Retracted 0 TED IBIT PR ROH MIN BOOM CPCITIES 140 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended ,300 57,600 41, ,000 44,200 31, ,000 35,500 25, ,500 29,500 20, ,900 21,600 14, ,000 16,600 11, ,000 13,300 8, ,100 10,800 6, ,900 9,000 5, ,200 7,500 4, ,900 6,300 3, ,700 5,300 2, ,800 4,500 2, ,900 3,800 1, Rotation 0 Retracted PROHIBITED 0 MIN BOOM CPCITIES 120 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended 360 Rotation ,400 57,800 41,400 26,600 26, ,200 44,400 31,600 19,900 20, ,200 35,800 25,200 15,700 16, ,700 29,700 20,800 12,700 13, ,100 21,900 15,000 8,700 9, ,300 16,900 11,400 6,300 7, ,300 13,600 8,900 4,600 5, ,400 11,100 7,100 3,400 4, ,200 9,300 5,700 2,500 3, ,500 7,800 4,600 1,700 2, ,100 6,600 3,700 1, ,000 5,600 3,000 Retracted 0 ED PRO OHIB BITE P MIN BOOM CPCITIES 150 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended ,700 53,700 41, ,800 44,000 31, ,900 35,400 24, ,400 29,300 20, ,700 21,400 14, ,800 16,500 10, ,800 13,100 8, Rotation 0 Retracted ,900 10,700 6,600 PROHIBITED ,800 8,800 5, ,100 7,300 4, ,700 6,100 3, ,600 5,200 2, ,600 4,300 1, ,800 3, ,100 3,000 0 LS 208H

24 B MIN BOOM CPCITIES 160 FT OPEN THROT TUBE BOOM Over End Blocked B B Extended ,600 43,900 31, ,800 35,200 24, ,200 29,200 20, ,600 21,300 14, ,700 16,300 10, ,700 12,900 8, ,800 10,500 6, Rotation 0 Retracted ,600 8,600 5,100 PROHIBITED ,900 7,200 4, ,500 6,000 3, ,400 5,000 2, ,400 4,200 1, ,600 3, ,900 2, ,300 2,300 0 MIN BOOM CPCITIES 180 FT OPEN THROT TUBE BOOM Over End Blocked B B ,500 37, ,800 34, ,900 28, ,300 20, ,300 16, ,300 12, ,400 10, ,300 8, ,500 6, ,200 5, ,000 4, ,100 3, ,300 3, ,600 2, ,000 2, ,500 1,500 Extended 360 Rotation 0 PROHIBITED Retracted 0 MIN BOOM CPCITIES 170 FT OPEN THROT TUBE BOOM Over End Blocked B B ,400 42, ,300 35, ,100 29, ,400 21, ,500 16, ,500 12, ,600 10, ,400 8, ,700 7, ,300 5, ,200 4, ,300 4, ,500 3, ,800 2, ,200 2, ,600 1,700 Extended 360 Rotation 0 PROHIBITED Retracted 0 MIN BOOM CPCITIES 190 FT OPEN THROT TUBE BOOM Over End Blocked B B ,900 32, ,500 32, ,900 28, ,900 20, ,200 15, ,200 12, ,300 10,000 Extended 360 Rotation ,100 8,100 PROHIBITED ,400 6, ,000 5, ,900 4, ,900 3, ,900 2, ,000 2, ,100 1,800 Retracted 0 Note: Refer To Page 7 For Capacity Deductions Caused By ny Jib ttachment Or Tip Extension. LS 208H

25 This page intentionally left blank LS 208H

26 Link Belt Construction Equipment Company Lexington, Kentucky Link Belt is a registered trademark. Copyright ll rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications. LS 208H

27 Jib Capacities Hydraulic Lattice Crawler Crane LS 208H II 80 ton (72.6 metric ton) Tube + Jib ( m) Tube with ( m) of Jib 180 (54.9 m) Tube with 30 (9.14m) or 45 (13.7 m) of Jib 20 (6.10 m) Open Throat Top Section with 32 (0.81 m) Wide x 24 (0.61) Deep Jib Extended Blocked Capacities 360 Degree Capacities B Counterweight Options 20 2 (6.15 m) Crawler Length LS 208H II CUTION: This material is supplied for reference use only. Operator must refer to in cab Crane Rating Manual to determine allowable machine lifting capacities and operating procedures.

28 TUBULR JIB NOTES FOR TUBE BOOM 1. Capacities are for a LS 208H crawler crane with B (39,700 lb) counterweight. 2. Separate capacity charts are listed for 360 and for over end blocked crawler working areas. Verify operating conditions as described on the Working rea Chart found in the general information section of this Crane Rating Manual. pply the appropriate lift capacity chart based on the working area and the specific operating conditions. 3. Over end blocked capacities can be lifted over either end with the crane standing level on a firm supporting surface. dequate blocking must be placed under both treadmember sprockets (or idler rollers) at the end that the load is to be lifted to prevent rocking. The ramps supplied with the machine are considered to be adequate blocking. 4. Capacities are for side frames in the extended position only and are based on the crane standing level on a firm supporting surface. 5. Capacities are limited to a LBCE 44 x 54 tube boom with an open throat and a LBCE 12 ton, 24 x 32 cross section tube jib with a 11 6 high jib mast properly assembled. 6. Two parts of 1 Diameter Type RB wire rope are required for maximum lift. 7. Capacities are for 30, 45, and 60 jib lengths only. 8. Maximum boom plus jib combination is or The only jib lengths available on the 180 tube boom are 30 and The least stable condition is over the side. 10. ll capacities are listed in pounds and are not more than 75% of the tipping loads. Shaded capacities are governed by factors other than those that would cause a tipping condition. 11. deduction must be made from the jib capacities for the weight of the following: Main boom hook block or hook ball, jib hook block or hook ball, slings, grapple, etc. B Tubular Jib Offset Diagram

29 WORKING RNGE DIGRM Maximum See Note Jib Length 190 in feet above ground Minimum See Note Main Length Operating radius from centerline of rotation. CL OF ROTTION

30 WORKING RNGE DIGRM Maximum See Note Jib Length in feet above ground Minimum See Note Main Length Operating radius from centerline of rotation CL OF ROTTION

31 LS-208H II - w/ 44" x 54" Tube, w/ 24" x 32" Tube Jib, w/ "B" Ctwt Refer to the Tubular Jib Notes For Tube in this Crane Rating Manual before operating the crane. Jib to Length Jib Length Jib 5 Degrees 15 Degrees 25 Degrees Jib ,000 24, ,000 24, ,000 24, ,000 24, ,000 24, ,000 24, ,000 24, ,800 19, ,000 24, ,700 23, ,800 17, ,000 24, ,100 21, ,700 16, ,000 21, ,400 17, ,100 15, ,400 17, ,300 16, ,400 13, ,000 24, ,000 24, ,000 24, ,200 19, ,700 21, ,900 16, ,000 19, ,700 16, ,500 12, ,700 16, ,600 13, ,600 10, ,700 13, ,500 11, ,200 9, ,600 11, ,000 10, ,200 8, ,200 10, ,000 24, ,100 21, ,100 18, ,600 16, ,800 13, ,800 13, ,100 11, ,500 8, ,300 11, ,300 9, ,300 7, ,500 9, ,000 8, ,400 6, ,200 8, ,100 7, ,700 5, ,300 7, ,300 6, ,000 24, ,000 24, ,000 24, ,000 24, ,600 20, ,000 24, ,000 24, ,700 18, ,000 24, ,900 22, ,100 17, ,700 22, ,000 19, ,900 15, ,600 17, ,700 16, ,300 14, ,800 14, ,700 14, ,000 24, ,000 24, ,000 24, ,600 23, ,700 17, ,700 20, ,600 16, ,000 13, ,600 16, ,600 14, ,100 11, ,200 15, ,400 12, ,700 9, ,900 12, ,800 10, ,700 8, ,200 11, ,600 9, ,900 7, ,000 10, ,000 24, ,500 22, ,400 19, ,000 17, ,400 14, ,000 15, ,800 11, ,800 8, ,300 12, ,900 9, ,600 7,600 60