Safir-M digital. Features. LCD indicator and controls. Industries. Applications

Transcription

1

2

3

4 Features Reference accuracy, % FS (draft pressure) Turndown 1:25 Output 4 20 ma, 0 5 ma Linear (increasing or decreasing) Square root (differential pressure) Damping (optional), s Explosion protection Intrinsically safe 0ExiaIICT5X Explosion proof 1ExsdIIBT5 Special design for oxygen media Build-in LCD indicator or handheld control unit Mean time before failure hours (25 C), hours (40 C) Warranty period 36 months Inter calibration period 24 months LCD indicator and controls Units displayed Pa, kpa, MPa kgf/m 2, kgf/cm 2 % of span Functions Zero adjustment Upper range value adjustment Predefined range selection Damping selection User defined upper range value Output trim Output function selection Thermal power stations Metallurgy Oil & Gas production Pipelines Refinery & Chemicals Machinery Industries Applications Process management Protection and safety systems Custody transfer and Flow measurement 4

5 Pressure ranges Predefined pressure ranges are formed from the set (1.0, 1.6, 2.5, 4.0, 6.3) by decimal shifting to left or right. These values may be used with the following physical units: kpa (MPa), kgf/m 2 (kgf/cm 2 ), mbar (bar). The table bellow represents pressure ranges for particular model number. abso -lute gage gage (neg.) gage (neg./pos.) differential hydro Model number Ра кpа MPа 40,0 63,0 100,0 160,0 250,0 400,0 630,0 1,0 1,6 2,5 4,0 6,3 10,0 16,0 25,0 40,0 63,0 100,0 160,0 250,0 400,0 630,0 1,0 1,6 2,5 4,0 6,3 10,0 16,0 25,0 40,0 63,0 100, * , 5133, 5135, , 5143, 5145, , 5155, , 5161, 5163, , 5172 * * , 5233, 5235, , 5243, 5245, * , 5333, 5335, , 5343, 5345, , 5355, * , , , , 5536, 5537, 5547 pressure level flow Notes 1. Span limits (min and max) are indicated. 2. LRV equals to 0 for absolute, gage, differential and hydrostatic pressure transmitters 3. Transmitters might be supplied being configured at PPR or user specified ranges with the following limitations: URV should be algebraically greater than LRV, except gage (negative) transmitter for which pressure axis is reversed URV shouldn t be more than URL for the model number Span shouldn t be less then minimal one for the model number 4. Transmitters with model numbers xx01 should be used for gases only with LRV = 0 5

6 Accuracy Hereafter all the metrological characteristics are expressed as output deviation relative to output range. Reference accuracy, % (includes hysteresis, linearity, and repeatability) Model numbers URV or Turndown xx kpa < URV URV 0.1 kpa xx10 1 TD < TD xx 1 TD < TD < TD others 1 TD < TD < TD Ambient temperature effect (per 10 C, ref. temp. 23 C) Ref. accuracy Temperature effect, % TD TD TD TD Static pressure effect Model numbers Static pressure, MPa Static pressure effect, % per x xtd 0.1 MPa x xtd 1 MPa 2.5 < xtd 1 MPa x xtd 1 MPa 4 < xtd 1 MPa x xtd 1 MPa 4 < xtd 1 MPa 10 < xtd 1 MPa x430, x440, x450 x434, x444, x454, x464 x520, x530, x540, x xtd 1 MPa 10 < xtd 1 MPa xtd 1 MPa xtd 1 MPa 2.5 < xtd 1 MPa Power supply effect, % per 1 V Load effect, % 0.01 per 100 Ohm Output variations, % to 5 Hz to 10 6 Hz Magnetic field effect < ref. acc. 400 A/m at 50 Hz Vibration effect, % 1.0 x TD for xx01, xx10, xx15, xx x TD other model numbers Response time, s 1.6 for xx01, xx other model numbers 6

7 Operating conditions Ambient temperature & humidity (should be specified in ordering form) UHL3.1*(+5 +50) t (+5 +50) C, h 95±3 % at 35 C UHL3.1*(+5 +80) t (+5 +80) C, h 95±3 % at 35 C U2*( ) t ( ) C, h 95±3 % at 35 C condensation not permissible U2*( ) t ( ) C, h 95±3 % at 35 C T3** t (-5 +80) C, h 100 % at 35 C condensation permissible *Max process temperature 120 C Static pressure limits (differential or hydrostatic pressure) Model number MPa , 5520, 5530, 5540, , 5440, , 5444, Overpressure Absolute and Gage pressure 1.25 of URL Differential pressure 1.5 of static pressure from high pressure side pressure level flow Permissible vibrations Mechanical Shock Frequency 1 9 Hz, amplitude, mm 3.5 Peak acceleration, m/s2 70 Frequency Hz, acceleration, m/s Impulse duration, ms 50 Directions X,Y,Z Form half-wave Rate, 1/s 0.1 Directions X,Y,Z Ingress Protection Rating IP66 EMC Interference type Test level Criteria Additional error, % Electrostatic discharge IEC A 0.1 Surge immunity IEC line-to-line line-to-ground 3 4 A 1.0 Fast transient/ Burst immunity IEC A 1.0 Radio-frequency electromagnetic field IEC A 1.0 Pulse magnetic field immunity IEC A 0.1 EM Interference Interference voltage on power supply lines Emission limits Frequency, MHz Interference voltage [db μv] Quasi peak value Average value Frequency, MHz Distance, m Interference MF intensity [db μv/m] From 0.15 to From 30 to From 0.5 to From 230 to

8 Output 8

9 Wiring Power supply voltage y (36 ± 0.72) V for transmitter with 0 5 (5 0) ma output y V for transmitter with 4 20 (20 4) ma output, power supply minimal voltage U PS is calculated as U PS = I MAX RL + U MIN, where RL overall load resistance, including control/measuring device, wire etc. IMAX maximal output (20 ma) UMIN 15 V, minimal voltage for transmitter without load. Power consumption of transmitter powered with 36 V: y 1.4 W for transmitter with 0 5 (5 0) ma output y 0.8 W for transmitter with 4 20 (20 4) ma output Explosion Protection Type, Output, Loop Type, and Load Explosion protection type Output, ma Loop type Load, Ω Without explosion protection Explosionproof Intrinsically safe or 4-wire R L U PS U MIN I MAX 4-wire 50 to wire Depends on safety barrier and/or power supply pressure level flow Male part for control unit connection LCD Cover Z button Control Buttons Electronic module of transmitter with handheld control unit Electronic module of transmitter with built-in control unit 9

10 Electronic module. General purpose and intrinsically safe type Transmitter with electrical connector Explosionproof type transmitters Transmitters with LCD. Explosionproof type 10

11 Transmiter with cable entry Transmitter with electrical connector pressure level flow Four-Wire Loop Diagram (5-0 ma or 4-20 ma) Transmitter with cable entry Transmitter with electrical connector Two-Wire Loop Diagram (4-20 ma) 11 Надежность датчиков

12 Typical design of differential pressure transmitter Fixing screw for enclosure cap 2 Enclosure cap with sight glass 3 Electronic module O-Ring 4 Control board with 3 screws 5 Ribbon cable 6 Grounding hole with bolt, gaskets and washer (external) 7 Fixing screw for housing 8 Electrical conduit 9 Upper nameplate 10 Electronics housing 11 Grounding hole with bolt, gaskets and washer (internal) 12 2 nuts 13 Enclosure cap 14 Process flange gaskets 15 Process flange nuts 16 Cap for process connection port 17 Process flange 18 Sealing screw 19 Drain / vent valve 20 Process flange O-Ring 21 Sensor module 22 Belt nameplate 23 Z button cover 24 Blank conduit 25 Process flange screws

13 Weights Model Numbers Weight, kg, no more than 5030, 5040, , 5140, 5150, 5160, 5170, 5230, 5240, 5330, 5340, 5350, , 5151, 5161, 5171, , 5210, , 5215, , 5220, , 5201, , 5424, 5430, 5434, 5440, 5444, 5450, 5454, 5460, , 5530, 5540, 5550 with DN , 5530, 5540, 5550 with DN , 5152, 5162, 5242, 5342, , 5148, 5158, 5168, 5238, 5248, 5338, 5348, , 5145, 5155, 5235, 5245, 5335, 5345, pressure level flow 13

14 Ordering information For better quotation processing please follow the specified options order. Separate options with -. Safir-M Explosion protection type (if required) Intrinsically Safe Explosionproof IS EP Model number (see Table 6-1.) Special requirements (optional) Extra burn-in 360 h Remote seal Oxygen application (wetted parts code 02 only) (inert filling liquid, cleaned) Wetted parts materials code See Table on page 13 for details Attn.: check the availability for particular model number Ambient conditions code Temp. (+5 +50) C, humidity* 95±3 % at 35 C Temp. (+5 +80) C, humidity* 95±3 % at 35 C Temp. ( ) C, humidity* 95±3 % at 35 C Temp. ( ) C, humidity* 95±3 % at 35 C Temp. (-5 +80) C, humidity** 100 % at 35 C * condensation not permissible ** condensation permissible Reference accuracy code (see Table on page 4) Pressure ranges with units (see Table on page 3 with notes) Static pressure in MPa (for model numbers 54xx and 55xx, see Table on page 4) Output signal code y0 5 ma y0 5 ma square root y5 0 ma y4 20 ma y4 20 ma square root y20 4 ma Control unit Built-in Handheld (omit option if not required) Mounting Kit Code (optional) Nominal Diameter DN (for model numbers 55xx and 5xx5) DN 50 DN 80 5xxx XB RS OX 02, 03, 04, 06, 11, 12 UHL3.1*( ) UHL3.1*( ) U2*( ) U2*( ) T3**( ) 0,1; 0,15; 0,25; 0,5 ХХХ ХХ BI HH Mxx D50 D Electrical Connector (if required) Not compatible with option -IS 14 Upper Pressure Limit for the Model with Unit (ХХ) C

15 Code Diaphragm Material Stainless steel 12H18N10T Wetted parts Material Wetted parts materials Marking O-Ring/ gasket material Model numbers All except 2051, 2151, 2161, 2171, 2351, 2x10, 2x01, 2020 Stainless steel NBR or Fluoroelastomer 15 12H18N10T SKF-26NM Alloy 36NHTU 2x10, 2x01, 2020 Stainless steel 12H18N10T Hastelloy C X18H10T Teflon-coated Titanium alloy Titanium alloy Stainless steel 12H18N10T Stainless steel 12H18N10T Stainless steel 12H18N10T Stainless steel 12H18N10T 15 Fluoropolymer F , 2151, 2161, 2171, 2351 Titanium alloy , 2151, 2161, 2171, 2351 Notes: 1. Stainless steel 12H18N10T in accordance with GOST (C < 0.12 %, Cr %, Ni 9 11 % Ti, Fe), equivalent to AISI 316L or AISI 304L. 2. Alloy 36NHTU in accordance with GOST (Ni %, Cr %, Ti %, Al %, Fe %, Si, Mn), equivalent to Invar Hastelloy in accordance with EN Titanium alloy VT9 in accordance with GOST (Ni, Al %, Mo %, Zr %, Si %, Fe 0.25 %). 5. Fluoropolymer F4 (PTFE) in accordance with GOST pressure level flow 15

16 Model numbers 5030, 5040, , 5140, 5150, 5160, , , 5340, 5350 Pressure ranges Min Pressure type Model numbers Span, URL, kpa from to kpa Absolute kpa 0 63 kpa kpa kpa kpa MPa Gage kpa 0 63 kpa kpa kpa kpa MPa MPa 0 25 MPa MPa 0 63 MPa Gage, kpa 0-63 kpa negative kpa kpa Gage, kpa kpa positive/negative kpa kpa kpa MPa Measuring unit diagram Electronic housing 2. Diaphragm type silicon sensor 3. Inner cavity with filling liquid 4. Protective diaphragm 5. Process nipple 6. Cable gland 7. Cavity (vacuum for absolute pressure) 8. Measuring unit body 9. Gasket 10. Stop screw 11. Pressure port

17 Dimensions pressure level flow Typical mounting and piping 1. Nut M20 2. Copper Gasket 3. Nipple Type 1 4. Connection Nut 5. Nut M8 6. Washer 8 7. Mounting Bracket Type 3 8. U-bolt See chapter Mounting kits for details 17

18 Model numbers 5151, 5161, Pressure type Model numbers Pressure ranges from to Min Span, kpa URL, kpa Gage kpa MPa MPa 0 25 MPa MPa MPa Gage, positive/negative kpa MPa Measuring unit diagram Electronic housing 2. Cavity (vacuum for absolute pressure) 3. Cable gland 4. Diaphragm type sensor (silicon-on-sapphire) 5. Pressure port 6. Process nipple

19 Dimensions pressure level flow Typical mounting and piping 1. Nut M20 2. Copper Gasket 3. Nipple Type 1 4. Connection Nut 5. Nut M8 6. Washer 8 7. Mounting Bracket Type 3 8. U-bolt See chapter Mounting kits for details 19

20 Model number 5172 Pressure type Model numbers Pressure ranges from to Min Span, MPa Gage MPa MPa URL, MPa Measuring unit diagram Electronic housing 2. Diaphragm type sensor (silicon-on-sapphire) 3. Inner cavity with filling liquid 4. Flange 5. Protective diaphragm 6. Cavity (atmospheric pressure) 7. Body 8. Gasket 9. Bolts 10. Pressure port 10 20

21 Dimensions pressure level flow 21

22 Model numbers 5133, 5135, 5138, 5143, 5145, 5148, 5153, 5155, 5158, 5163, 5168, 5233, 5135, 5138, 5243, 5245, 5248, 5333, 5335, 5338, 5343, 5345, 5348, 5353, 5355, 5358 Pressure type Model numbers Gage Gage, negative Gage, positive/ negative Pressure ranges from to Min Span, kpa URL, kpa 5133, 5135, kpa 0 63 kpa , 5145, kpa kpa , 5155, kpa MPa , MPa 0 25 MPa , 5235, kpa 0-63 kpa , 5245, kpa kpa , 5335, kpa kpa , 5345, kpa kpa , 5355, kpa MPa Measuring unit diagram xxx3 xxx5 xxx Р Diaphragm type silicon sensor 2. Body 3. Inner cavity with filling liquid 4. Protective diaphragm

23 Dimensions Model numbers Model numbers pressure level flow Model numbers

24 Model numbers Pressure ranges Min Pressure type Model numbers Span, URL, kpa from to kpa Gage kpa kpa Gage, negative kpa kpa Gage, positive/ negative kpa kpa Measuring unit diagram Р Р atm Cable gland 2. Lever type sensor (silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Hard centre 6. O-ring 7. Flange 24

25 Dimensions pressure level flow Typical mounting and piping 1. Connection Nut 2. Nipple Type 1 3. Gasket 4. Nipple M20x See chapter Mounting kits for details 25

26 Model numbers Pressure type Model numbers Pressure ranges Min Span, from to kpa URL, kpa Gage kpa 0 4 kpa Gage, negative kpa 0-4 kpa Gage, positive/negative kpa -2 2 kpa Measuring unit diagram Р Р atm Cable gland 2. Lever type sensor (silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Hard centre 6. O-ring 7. Flange 26

27 Dimensions pressure level flow Typical mounting and piping 1. Bolt M10x14 2. Washer U-bolt 4. Mounting Bracket Type 1 5. Nut M8 6. Washer See chapter Mounting kits for details 27

28 Model numbers 5115, , , 5320 Pressure type Gage Gage, negative Gage, positive/negative Model numbers Pressure ranges from to Min Span, kpa URL, kpa kpa 0 10 kpa kpa 0 25 kpa kpa 0-10 kpa kpa 0-25 kpa kpa -5 5 kpa kpa kpa Measuring unit diagram Р Р atm Cable gland 2. Diaphragm type sensor (silicon or silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Overpressure diaphragm 6. Flange 7. O-ring 28

29 Dimensions pressure level flow Typical mounting and piping 1. Bolt M10x14 2. Washer U-bolt 4. Mounting Bracket Type 1 5. Nut M8 6. Washer See chapter Mounting kits for details 29

30 Model number 5401 Pressure type Model numbers Pressure ranges from to Min Span, kpa URL, kpa Static pressure, MPa Differential kpa 0 1 kpa Measuring unit diagram Р Р Cable gland 2. Lever type sensor (silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Hard centre 6. O-ring 7. Flange

31 Dimensions pressure level flow Typical mounting and piping 1. U-bolt 2. Nut M8 with Washer 8 3. Mounting Bracket Type 1 4. Bolt M10x14 5. Washer See chapter Mounting kits for details 31

32 Model number 5410 Pressure type Model numbers Pressure ranges from to Min Span, kpa URL, kpa Static pressure, MPa Differential kpa 0 4 kpa Measuring unit diagram Р Р Cable gland 2. Lever type sensor (silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Hard centre 6. O-ring 7. Flange 32

33 Dimensions pressure level flow Typical mounting and piping Gasket Fluorine Rubber 2. Bolt M10x25 with Washer valve Manifold H-Type 4. Flange 5. Nipple Type 1 6. Bolt M10x40 7. Flange Adapter 8. Bolt M10x55 Note: Multiple parts are shown by sample See chapter Mounting kits for details 33

34 Model numbers 5415, 5420, 5430, 5434, 5440, 5444, 5450, 5454 Pressure type Differential Model numbers Pressure ranges from to Min Span, kpa URL, kpa Static pressure, MPa kpa 0 10 kpa kpa 0 25 kpa kpa 0 63 kpa kpa 0 63 kpa kpa kpa kpa kpa kpa MPa kpa MPa Measuring unit diagram Р Р Cable gland 2. Diaphragm type sensor (silicon) 3. Body 4. Protective diaphragm 5. Overpressure diaphragm 6. Flange 7. O-ring

35 Dimensions pressure level flow Typical mounting and piping 1. Gasket Fluorine Rubber 2. 3-valve Manifold Coplanar 3. Flange with Nipple 4. Bolt M10x55 5. Copper Gasket 6. Nipple Type 2 7. Connection Nut Note: Multiple parts are shown by sample See chapter Mounting kits for details 7 35

36 Model number 5464 Pressure type Model numbers Pressure ranges from Min Span, kpa URL, kpa Static pressure, MPa Differential MPa 0 16 MPa to Measuring unit diagram Cable gland 2. Diaphragm type sensor (silicon-on-sapphire) 3. Body 4. Protective diaphragm 5. Flange 6. O-ring Р Р

37 Dimensions pressure level flow Typical mounting and piping Valve H-type Manifold (assembled) 2. Nut M8 3. Washer 8 4. U-bolt 5. Bolt M8 with Washer 8 6. Mounting Bracket Type See chapter Mounting kits for details 37

38 Model numbers 5520, 5530, 5540, 5550 Pressure type Hydrostatic Model numbers Pressure ranges from to Min Span, kpa URL, kpa kpa 0 25 kpa kpa 0 63 kpa kpa kpa kpa MPa Static pressure Measuring unit diagram Р Р Cable gland 2. Diaphragm type sensor (silicon) 3. Body 4. Protective diaphragm 5. Overpressure diaphragm 6. Flange 7. O-ring

39 Dimensions pressure level flow Typical mounting 39

40 1. Bolt M16 (recommended) 2. Vessel Flange 3. Gasket 4. Washer Nut M See chapter Mounting kits for details Design with remote seal 180 nчш max Ш80 D 3 D D 1 D 2 21 А D D1 D2 D3 n DN DN

41 Design with two remote seals pressure level flow 41

42