Pneumatic Connectors handbook. Catalogue 0093-UK January 2002

Transcription

1 Pneumatic Connectors handbook Catalogue 0093-UK January 2002

2 Selection guide pplication Working pressure Tube Ermeto Hose Pneumatic automation Pneumatic power Industrial fluids ggressive environments Primary vacuum - 0 bar 0-0 bar 0-6 bar 6-8 bar 8-25 bar bar bar Pneumatic copper tube installations * (2) * * Chemical nickel plated only. ** Prestoweld 2 tubing only () vailable with threaded ends only. Depends on fitting type used to connect to the tube bar Polyurethane tube PE tube Polyethylene tube Polyamide /2 tube ** () () () () () () () () () () () () () () () () () () () () () () Copper tube Steel Stainless Steel Synthetic rubber () () Polyurethane Prestolok 2 Prestolok icro Prestolok Prestoweld 2 Pneu. int. funct. ftgs. etrulok P Ermeto rass adaptors rass adapt. for automotive industry Pneumatic adaptors all valves Quick couplings Hose and fittings Ther. Sin tub. and Pn.-TU.u. (2) Welding sparks. For more detailed information, please consult the section corresponding to the selected product from this catalogue. For your safety! Under certain circumstances, tube fittings can be subjected to extreme loadings such as vibration and uncontrolled pressure peaks. Only by using genuine Parker components and following the Parker assembly instructions can you be assured of the reliability and safety of the products and their conformity to the applicable standards. Failure to follow this rule can adversely affect the functional safety and reliability of products, cause personal injury, property damage, and result in loss of your guarantee rights. In any case, guarantee is limited only to the Parker products.

3 General index (an index by part number is also available at the end of this catalogue) Design manual Prestolok 2 Prestolok icro Prestolok Prestoweld 2 Technical data, pneumatic system calculations, installation guide. Push-in fitting with thermoplastic body and protective cap for pneumatic applications. ini push-in fitting with thermoplastic body for miniature pneumatic applications. rass push-in fitting for fluid and arduous pneumatic applications. Spark resistant push-in fittings. C D E Pneumatic integrated function fittings complete range from flow control to end of stroke pressure sensors. F etrulok P Ermeto Ready for use brass bite type fitting for use with copper or plastic tubin two piece fitting specifically designed for plastic tubin ite type fitting for use with metal or plastic tubin G H I rass adaptors wide range of configurations and thread terminations. J rass adaptors for automotive industry Pneumatic adaptors wide range of adaptors for air and water cooling circuits for welding applications. wide range of adaptors for pneumatic applications. K all valves rass ball valves for many fluid handling applications. Quick couplings Push-ok hose and fittings Thermoplastic single tubes and Pneumo-Tube bundles ccessories rass and steel quick couplings, as well as blow guns for all pneumatic applications. ow-pressure ; self-grip hose without clamps. Polyamide, Polyethylene, Polyurethane tubing for all pneumatic applications. ccessories for pneumatic installations. N O P Q Parker s mission To be an outstanding manufacturer who, through continuous productivity and quality improvements, makes effective, profitable use of its ressources to produce customer-satisfying products and services.

4

5 Pneumatic connectors design manual

6 Pneumatic connectors design manual Catalogue 0093-UK

7 Index Pneumatic connectors design manual Pages The Parker pneumatic connection system 2-3 Thread configurations SPP and SPT pipe threads 4 ISO metric pipe threads 5 UNF threads 6 NPT threads 7 The sealing of threaded connections Parallel threads 8 Taper threads 9 Threaded connections and corrosion tmospheric corrosion 0 Compatibility of different base metals Hose and tubing used in pneumatics Polyamide tubing / PE tubing 2 Polyurethane tubing 3 Hoses 3 to 5 Copper and steel tube 5 Pneumatic system calculations Power losses 6 Calculation of flow rate 7 Orifice diameter for different cylinders 8 Cylinder response time 9 ir admission time 9 aximum recommended flow 20 Pressure drop through shaped 20 components ir consumption 20-2 eakage 2 Installation guidelines 22 to 25 Pneumatic control Cylinders, integrated fittings (flow control valves, check valves, exhaust valves, silencers) Connectors for pneumatic systems rass push-in fittings 28 rass and steel connectors 29 Terms used in pneumatics 30-3 Pneumatic symbols 32 to 34 Pneumatic Quick Coupling profiles 35 Catalogue 0093-UK

8 The Parker pneumatic connection system For more than 60 years, Parker has developed and manufactured the most complete range of components to serve hydraulic and pneumatic markets. The specific range of pneumatic connectors is designed and manufactured in accordance with international standards to meet market requirements. The objective of this manual is to aid the design engineer in the selection of pneumatic connectors for specific or general applications, dependant upon the individual constraints of the system. The information enclosed should be considered as a basic guideline only. For further detailed information with regard to pneumatic systems, please contact your Parker sales engineer. The Parker pneum EO Ermeto Original: ite type tube fitting system with metal or soft sealing for use with either metal, copper or polyamide tubing plastic tube copper tube plastic tube Push-ok Hose and fittings : low pressure, self grip hose ssembly without clamps or special tools etrulok : one piece ready to use bite type fitting for use with either copper or plastic tubing copper tube low Guns : with or without safety valving Pneumatic Quick couplings : flow from 550l/ min

9 atic fitting system Prestolok icro : iniature push in fitting for polyamide and polyurethane tubin all Valves : a wide range for many pneumatic applications Prestolok 2 : Push-in fitting with protective cap for polyamide and polyurethane tubin Prestolok : Push-in fitting for polyamide, polyurethane and copper tubing Prestoweld 2 : Spark resistant push-in fittings Thermoplastic single tubes and Pneumo Tube bundles P : two piece fitting for all types of plastic tubin

10 Pneumatic connectors design manual Thread configurations SP threads SPP min. for SPT SPT 6.25 cone angle. Pressure-tight joints on the thread SPP Peripheral sealing (copper, aluminium, bonded, etc.) SPP and SPT pipe threads SPP and SPT threads have a thread angle of 55 and are the most widely used fastening threads in pneumatic applications. The spot face surface must be square to the pitch diameter and free from longitudinal and spiral tool marks. SPP - ritish Standard Pipe Parallel threads for tubes and fittings where pressure-tight joints are not made on the thread, i.e., a peripheral seal is used. SPT - ritish Standard Pipe Taper threads for tubes and fittings where pressure-tight joints are made on the threads. It is accepted practice to fit a SPT S 2 male thread into a SPP female DIN 3852 port tapping for pneumatic applications. In certain exceptional cases the port may also be tapered. SPP SPT Threads d l 2 d 4 a l b b 2 per nominal min. max. max. min. min. inch Rs /8 R / Rs /4 R / Rs 3/8 R 3/ Rs /2 R / Rs 3/4 R 3/ Rs R Thread standards SPP thread to : ISO 228- S2779 DIN Form,,E NF E SPT thread to : ISO 7 S 2 DIN Form C NF E Screwed studs and tapped holes to DIN 3852, form X, Z Rs./4 R./ Rs./2 R./ Note The letters Rs are the accepted designation for a SPP thread and the letter R represents a SPT thread. 4 Catalogue 0093-UK

11 Pneumatic connectors design manual Thread configurations ISO metric pipe threads ISO 649 O-Ring sealing ISO 26 Peripheral sealing (copper, aluminium, bonded, etc.) ISO metric pipe threads ISO metric pipe threads have a thread angle of 60. They have mostly been used in miniature pneumatic applications because of the availability of small thread diameters, especially 5 and 3*. They are also used extensively in the automotive industry. There are two forms of sealing on metric threads.. O-Ring sealing into a profiled port in accordance with ISO Peripheral sealing eg copper or bonded washer in accordance with ISO 26 and 262 Thread standards O-Ring sealing : ISO 649 DIN Form F Peripheral sealing : ISO R26 and R262 DIN Form G NF E03-03 Seals : DIN 7603 NF E2-35 d l f g d 3 d 5 α b 2 a 2 Seal 3x0.5** x0.8** x.5 Ports : DIN Part 3 * 3, 5 and 20 threads are not included in the ISO specification 8x x.5 0x x.5 2x x2. 4x x2. 6x x2. 8x x2. 20x.5** x2. 22x x2. ** Not ISO Catalogue 0093-UK

12 Pneumatic connectors design manual Thread configurations UNF threads 60 UNF threads The Unified thread has a thread angle of 60, and is normally used in hydraulic applications. It also referred to as the "ISO inch size thread". UNF - Unified Fine threads for connections where pressure-tight joints are not made on the threads, i.e., a peripheral seal is used. Reference example : 3/8-24-UNF2 3/8 = diameter 24 = number of threads per inch = external threads = internal threads = low precision 2 = general purpose 3 = high precision Thread standards SEJ54 (male threads) SEJ926 (female port) Thread size SE d d 3 d 5 b a f g l α O-ring and module min. min. ID Section threads per inch mm /6-24 UNF -2 2 inch /8-24 UNF -3 7/6-20 UNF -4 /2-20 UNF -5 9/6-8 UNF -6 3/4-6 UNF -8 7/8-4 UNF -0./6-2 UN -2.3/6-2 UN -4.5/6-2 UN -6 (8/6 = /2 = 2,7 = DN2) mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch Catalogue 0093-UK

13 Pneumatic connectors design manual Thread configurations NPT threads Finger tightening Spanner tightening 6.25% cone angle NPT threads The National Pipe Taper thread has a thread angle of 60, and is mainly used in the petrochemical and process industries. NPT - National Pipe Taper threads for connections where pressuretight joints are made on the threads utilising a thread sealant. NPTF - National Pipe Taper Fuel threads for connections where pressure-tight joints are made on the threads, without a thread sealant. Thread standards SE J NF E Thread Threads d l l 3 l 4 b 3 size per inch Threads mm / / / / / / /4 / /2 / Catalogue 0093-UK

14 Pneumatic connectors design manual The sealing of threaded connections Peripheral sealing of parallel threads Pressure-tight joints for screwed connections with parallel threads are achieved by placing a seal between the two machined faces Flat seals Washers and rings are manufactured in many different materials including copper, aluminium, fibre, plastics, etc. The tightening torque at assembly must be carefully selected so as to avoid compressing the seal to the point of extrusion. s a general rule, the fitting should be tightened with a spanner /4 turn from the fingertight position. onded seals Elastomer sealing rings bonded into metal washers. onded seals are reusable, and cater for a variation in the dimensional tolerances of the machined surfaces. O-rings Dependant upon the configuration of the female port or male thread, O-ring seals are fitted with or without back-up washers. Captive seal fully retained O-ring seal is assembled in the fittin This ensures correct alignment. On metric threads it is possible to use this sealing method on both ISO 26/262 and ISO 649 ports. 8 Catalogue 0093-UK

15 Pneumatic connectors design manual The sealing of threaded connections Interference sealing of taper threads Pressure-tight sealing of screwed connections with taper threads is achieved by the application of a sealant to the surface of the external male thread. PTFE tape One or two layers of PTFE tape are wound around the external taper thread, prior to assembly. It is recommended to leave the first two threads uncovered to avoid tape fragments entering the circuit during assembly, causing the possible malfunction of valves, filters, etc. Sealing compounds and liquid sealants. part from polymer joint compounds and air-drying liquid sealants, the most common thread seal is an anaerobic synthetic resin which cures in the absence of air. Following assembly and tightening, the curing process is induced by a catalytic reaction between the resin and the metal. Resins that contain PTFE ease disassembly. For applications in food related industries, the thread sealant must be to a specified food-grade. Connections are normally ready for operation after one hour's curing time. Complete curing may take up to 24 hours. Disassembly of the connection destroys the sealing surface. Parker pre-coated taper threads Parker taper threads are pre-coated with a solution of PTFE powder carried in an acrylic base. No additional sealant is necessary for an effective seal during assembly. The male pipe thread can be reused up to five times without the use of additional sealing material. 9 Catalogue 0093-UK

16 Pneumatic connectors design manual Threaded connections and corrosion Corrosion within pneumatic circuits and its consequences - piston seizing, leakage, jamming of control valves, reduced efficiency etc., is due to the combined action of atmospheric and electrolytic corrosion, the latter being largely predominant in pneumatic systems. In the electrolytic process, the water contained in the ambient relative humidity of the air plays the role of the electrolyte. The galvanic action is the result of the potential difference : Fi - potential difference between metals ; Fi 2 - electrolyte concentration differential ; Fi 3 and Fi 4 - air and oxygen content differentials. In threaded connections the three forms of electrolytic corrosion can occur in a number of combinations. In order to avoid corrosion two general principles should be applied. direction of current voltmeter direction of current saline solution with high oxygen concentration oxygen anode conductor cathode weak electrolyte solution (saline solution) strong electrolyte solution (saline solution) cathode area rust direction of current metal anode metal cathode anode area steel bar or other metal saline solution with low oxygen concentration electrolyte porous membrane Fi - Potential difference between metals Fi 2 - Electrolyte concentration differential Fi 3 - ir and oxygen content differentials air, oxygen rust cathode area, well oxygenated saline drop cathode untreated steel anode area, less oxygenated Fi 4 - Principle of corrosion with different oxygen concentrations. 0 Catalogue 0093-UK

17 Pneumatic connectors design manual Threaded connections and corrosion First rule : compatibility of different base metals The susceptibility of different base metals to corrosion whilst in contact, depends upon the difference between the contact potentials, or the electrolytic decomposition voltages of the metal involved. The greater the potential difference, the greater the tendency for corrosion. The metal with the higher negative potential forms the anode and is corroded. Examples : - brass on copper = very slight corrosion - brass on zinc = heavy corrosion - steel on zinc = medium corrosion - steel on copper = heavy corrosion Non-passivated stainless steel has a decomposition voltage of about 0.70 volts and is attacked vigorously by copper or brass. Passivated stainless steel has a reduced decomposition voltage of volts. Passivation is obtained by the direct oxidation of the chromium compounds contained in the steel. Surface damage from scratches, solder or other contaminants will expose the base metal, and reactivate the higher decomposition voltage. anodes cathodes etal Electropotential volts agnesium alloy G-3Z agnesium alloy G Zinc (as galvanized coating) luminium alloy -Z4G (T35) luminium alloy -Z8GU (Z2 plated) luminium luminium alloy -Z5GU (not plated) luminium alloy -G3 (with chrome) luminium alloy -G5 (with chrome) luminium alloy -U4SG Steel XC 8 S Cadmium (S plating) luminium alloy -U4G ead Chrome (as plating) Tin Tin solder rass U-Z5 NS Titanium alloy to rass U-Z Chemical nickel Stainless steel 8/8 (passivated) Copper (99,9%) Nickel Rhodium Platinum 0 Silver Gold corrosion corrosion free Second rule : dry compressed air Water acts as an electrolyte, and a close relationship exists between the relative humidity of air and electrolytic corrosion. The mass of water vapour contained in the air is measured in grams "g" of water vapour, per unit volume ( m 3 ) of air. The saturation temperature or dew point, is the temperature at which the relative humidity of the air is 00%. The corresponding mass of water vapour has an upper limit which is dependant upon, and increases with, temperature (see table). Cooling below the saturation temperature causes condensation through the formation of water droplets. In practice, electrolytic corrosion becomes significant when the relative humidity of the ambient air is in excess of 50%. Example : t an ambient temperature of 20 C, with an average 60% relative humidity of the air, a compressor delivering 000 Nm 3 /h of air, at a pressure of 7 bar, draws in 0.3 kg of water per hour. 7.4 x 0.6 = 0.3 g/m Nm 3 x 0.3 g = 0.3 kg/h This example indicates the importance of arranging for adequate cooling and drying of compressed air. Temperature in C Dew point Water vapour max. (saturation) g/m 3 ass of water vapour at 00% relative humidity Catalogue 0093-UK

18 Pneumatic connectors design manual Hose and tubing used in pneumatics Polyamide tubing Parker calibrated polyamide tubing is extruded in polyamide (P) for use with pneumatic fittings. This tubing is manufactured within the limits of CETOP RP54P / DIN recommendations, and is ideal for pneumatic applications. For continual use at high temperature we recommend tube which is protected against heat and light. dvantages - Good vibration/damping properties, - Tubing available in several colours for easy identification, - High abrasion resistance, - ow pressure drop, - No thermal expansion. Technical characteristics Working pressure The working pressure of polyamide tubing is dependant on the operating temperature. The working pressures shown are based on a design factor of 3: Working pressure (bar) urst pressure (bar) Tube size Temp. C. 3x0.60 4x0.65 4x 5x 6x 8x 0 x 0 x.25 0 x.5 2 x 4 x.5 6 x Tube size Temp. C. 3x0.60 4x0.65 4x 5x 6x 8x 0 x 0 x.25 2 x 4 x.5 6 x For chemical compatibility of polyamide tubing, please consult your Parker sales engineer. PE tubing (Polyether lock mides) PE tubing is manufactured from a compound of soft polyethers and hard polyamides. Chemical resistance The tubing is produced in various grades and can be protected against heat and light with appropriate additives. dvantages of PE tubing PE tubing has additional advantages over polyamide : - Greater flexibility than P 2 - Suitable for an operational temperature range of - 40 to + 80 C. - Excellent resistance to creep under load. Fluid Test condition Result oiling water 7 days/00 C Oil 7 days/20 C Gasoline premium 7 days/23 C cetone 7 days/23 C Trichlorethylene 7 days/23 C = excellent - = medium 2 Catalogue 0093-UK

19 Pneumatic connectors design manual Hose and tubing used in pneumatics Polyurethane tubing Parker calibrated polyurethane tubing is obtained by extrusion. Its material hardness is 95 Shore (slightly higher than 40 Shore D). This tubing is manufactured within the limits of NF E Its very high flexibility allows a small minimum bend radius for compact installations. dimensional inspection system based on advanced laser technology maintains a tight tolerance on the outside tube diameter. dvantages - Extreme flexibility with bend radii up to three times better than polyamide tubing allows for compact installations, - Tube available in several colours for line identification, - Good vibration resistance, - ight weight, - Reduced fitting time. Technical characteristics Working pressure The working pressure of polyurethane tubing is dependant on the operating temperature. The working pressure shown are based on a design factor of 3:. Working pressure (bar) urst pressure (bar) Temp. C. Tube size 3x0.45 4x0.75 5x 6x 8x.25 0 x.5 2 x Temp. C. Tube size 3x0.45 4x0.75 5x 6x 8x.25 0 x.5 2 x For chemical compatibility of polyurethane tubing, please consult your Parker sales engineer. Hoses Pneumatic hoses are typically made up of a liner, a braid reinforcement and a protective cover. The number of braids depends upon the pressure rating of the hose. The protective cover is perforated to prevent blister formation due to air diffusion. Hose lines are used for the connection of mobile, as well as stationary pneumatic machinery and equipment, eg, hand tools, mobile pneumatic cylinders, compressors, etc. Conductive and non-conductive braid reinforcement For applications in hazardous or inflammable conditions eg, air powered hand tools that produce static electricity, or hand tools that may come into accidental contact with live electrical components, connections must be made using a hose with a conductive braid reinforcement. With mobile pneumatic equipment an additional connection to ground may be required if the conductivity of the metal braid is not sufficient. Conversely, certain types of equipment should be connected using hoses with non-conductive braid reinforcement, eg Parker Push-ok hose, to prevent the propagation of stray electric currents, for example electric welding or electrostatic spray paint equipment. Parker Push-ok hose and fittings The Parker Push-ok hose system is used for pneumatic applications up to 25 bar working pressure. The hose is assembled to fittings without the use of clamps. For a twist free installation when the pressure hose is assembled, at least one end should have a swivel type connection. For transition from copper or plastic tubing to Parker Push-ok hose lines, the etrulok FF swivel female end connection can be used. For chemical compatibility of hoses, please your Parker sales engineer. 3 Catalogue 0093-UK

20 Pneumatic connectors design manual Hose and tubing used in pneumatics Installation guidelines incorrect incorrect correct incorrect correct correct lways install hose lines with sufficient dip to compensate for movements during operation. length variation of + 2 to - 4% is acceptable. ake sure that the hose is not twisted. The marking on the hose and the use of swivel end fittings facilitate a twist- free installation. void acute bending of the hose adjacent to the rear of the hose connection. minimum length of three times the outside diameter of the hose is recommended between the rear of the hose connection and the beginning of the bend radius. For right angle configurations of the hose line, use elbow fittings to prevent stress on the connection due to the bend of the hose. void sharp edged configurations and protect hoses exposed to heavy chafing with metal spiral sleeves. If the risk of hose pull off during operation cannot be excluded, the hose line must be secured so as to prevent dangerous "whipping" of the hose following disconnection. incorrect correct End connection standards JIC 37 swivel female These hose nipples are typically used in hydraulic systems of US origin. Pipe thread UNF. Internal cone 74. Suitable adaptors are Triple-ok 37 flared fittings. Pipe threads : UNF - NPTF - metric - SPT - SPP. SE 45 swivel female These hose nipples are used in the automotive industry, and in refrigeration engineering for low and medium pressure applications. ody and swivel nuts can be used as JIC 37 and SE 45 adaptors, except for size -6 and -2 (different nipple). DIN end connections 24 cone, light and heavy series to DIN standards. Threaded fittings can be used as adaptors. 4 Catalogue 0093-UK

21 Pneumatic connectors design manual Hose and tubing used in pneumatics End connection standards SP swivel end connections SP swivel end connections are used with SP adaptors - internal cone 60. etrulok swivel end connections etrulok swivel end connections are designed to suit all etrulok fittings. Consult etrulok section. SPT male end connections SPT male end connections are used for direct connection to threaded ports. Standard imperial and metric steel and copper tubes Imperial sized copper tubing conforming to S287 Part 2 OD x wall thickness In etric sized copper tubing conforming to DIN NF 5 20 S278 Part 2 ID x OD mm etric sized steel tubing conforming to NF DIN 239C S746 ID x OD mm /8 x /6 x /4 x x 6 4 x 6 5/6 x x 8 6 x 8 3/8 x x 0 8 x 0 /2 x x 2 0 x 2 5/8 x x 4 2 x 4 4 x 6 4 x 6 3/4 x x 8 6 x x 20 7 x x 22 9 x 22 x x x 25./4x x x 30 5 Catalogue 0093-UK

22 Pneumatic connectors design manual Pneumatic system calculations Pressure drop caused by the frictional resistance of the rubber hose bore to the flow of the medium. (the pressure drop is expressed in bar per 0 m hose length) Hose bore and corresponding fitting /8 3/6 /4 5/6 dia.5 dia.6 dia.8 dia.0 Pressure bar Flow through 0 m hose length (Nm3/h) Power losses in pneumatic circuits Power loss or pressure drop in pneumatic circuits is the differential pressure p bar from inlet to outlet. For calculating the respective efficiency of pneumatic system components e. valves, fittings, tubing, the flow factor Cv is used. The figure corresponds to the volume of water (I) per unit time (min) that flows through a given component, dependent upon the differential pressure, p (bar). The U.S.. uses the same Cv factor, but expressed as US gallon/min. for a P in psi (Kv France = 4.3 Cv or Cv US = 0.07Kv) Germany uses a Kv factor which is defined in Nl/min. Note : the air volumes expressed in Nm 3 /min or Nl/min correspond to the relief flow rate at 6 bar delivery pressure. 3/8 /2 3/4 dia.2 dia In pneumatics, the flow rate Q is normally expressed in free air at standard reference atmospheric conditions, symbol NR. This does not apply to compressor output characteristics, which refer to intake volume and relative delivery pressure. QNR = Q rel. x P abs.i.e., manometric pressure + bar atm. 000 l/min NR = 00 l/min x (9 bar + bar atm.) dia dia.26 Recommended data Catalogue 0093-UK

23 Pneumatic connectors design manual Pneumatic system calculations Cv UK/US Kv France Kv Germany p Ql/min (NR) Calculation of flow rate as a function of Cv / Kv For upstream gauge pressure of 6 bar. Flow rate is inversely proportional to pressure. In a pneumatic cylinder, for example, the pressure increases from the beginning to the end of the stroke, whereas the flow rate decreases from its maximum value at the beginning of the stroke to zero at the end of the stroke. Considering a pneumatic component with a specified flow factor Cv/Kv, the flow rate Q, corresponding to any differential pressure p from inlet to outlet is calculated using the following equation : Q NR = Cv p x P abs. downstream Q = flow rate l/min free air Cv or Kv = flow factor p = differential pressure in bar P = abs. pressure downstream = abs. pressure upstream - p. abs. pressure upstream =manometric pressure + bar atm. Note : this equation is applicable so long as p is less than half the upstream pressure. The figures tabulated on the left are for air at 20 C ambient temperature, 65% rel. humidity and 03 mbar atmospheric pressure. 7 Catalogue 0093-UK

24 Pneumatic connectors design manual Pneumatic system calculations Orifice diameter for different cylinder types and speeds, for an upstream gauge pressure of 6 bar Valve Fitting ore Cv thread diameter mm / / Cylinder load % % 44 60% % 2 80% 47 70% % % % % % % aximum cylinder speed attainable without braking, for tube length of m (speed in mm/s) 5 Cylinder fitting /8 Cylinder fitting /4 Cylinder fitting 3/8 Cylinder fitting /2 Cylinder fitting 3/4 Cylinder fitting /8 / % % % Critical speed area % % / % % % Cylinders must never be subjected to 00% load in order to determine their efficiency (20% approx.) Notes : - The total displacement time is obtained by taking the travel time and adding the damping time, the response time (table, page 9) and the time required for air intake into tubing beyond m (table C, page 9). 2 - The speed and response time of a cylinder are not constant, but totally variable dependant on a number of factors such as : the inertia of the masses to be displaced, seating and sticking effect at the start of travel, the type of cylinder construction (seals, load distribution, etc.), the condition of the cylinder (wear, corrosion, etc.), whether the cylinder is mounted horizontally or vertically. The maximum performance values shown are approximate only, and are intended for the purpose of comparison. Depending on the operating conditions, these values could be reduced by half. 8 Catalogue 0093-UK

25 Pneumatic connectors design manual Pneumatic system calculations Cyl. dia Fitting thread 32 /8 50 /4 80 3/8 00 /2 25 /2 60 /2 Stroke mm Response time (s) Cylinder response time (table ) for 80% load, gauge pressure 6 bar, tube length m The average response times shown include an allowance for the time taken to empty the tubes and restore pressure. The values given are approximate only and subject to variation dependent upon the condition of the tubing and the cylinder. ir intake time for different tube lengths and diameters (table C), gauge pressure of 6 bar Hose ID mm Hose length in metres Time in seconds The temptation to reduce the pressure drop by choosing a large diameter tube should be resisted. Excessive over dimensioning will give an insignificant improvement in pressure drop at the expense of waste air and an increase in response time owing to the need to fill a greater volume. 9 Catalogue 0093-UK

26 Pneumatic connectors design manual Pneumatic system calculations aximum recommended flow through a pipe or hose in Nm 3 /h Pressure./2"./4" " 3/4" /2" 3/8" /4" /8" bar bore 40 bore 33 bore 26 bore 20 bore 5 bore 2 bore 8 bore Flow resistance within a fitting expressed as the equivalent length (m) of hose Type of fitting 90 elbow Tee or cross flow at 90 Tee or cross in line flow Fitting bore diameter in mm ir consumption distinction is made between hourly and instant air consumption. ) ir operated machines Example : actuating cylinder, diameter 00 mm, stroke length m, one cycle per minute, out stroke 0.8 s, return stroke 5 s. Hourly air consumption Cylinder area cm 2 x stroke cm = 7850 cm 3 Cylinder volume cm 3 x ( 6 bar + atm) x stroke and return = cm 3 (NR) during each cycle Consumption is 09.9 l x 60 = 6594 l/h (NR). Instant air consumption Cylinder area cm 2 x stroke cm = 7850 cm3 Volume cm 3 x (6 bar + atm) x stroke = cm 3 in Consumption is l x 60/0.8 = 4 2 l/mn (NR). Note : when calculating the air consumption of actuating cylinders the piston rod area can be disregarded. The example calculation illustrates that it is often necessary to provide for a pressure equalizing reservoir on the machine. ine volume With cylinders of short stroke length, the line volume between the directional control valve and the cylinder must be taken into account when calculating air consumption. Example : actuating cylinder as before, but with a stroke length of 00 mm, and 4 m connecting line, I.D. 2 mm. Hourly air cosumption Cylinder area cm 2 x 0 cm = 785 cm 3 Cylinder volume cm 3 x (6 bar + atm) x stroke and return = cm 3 (NR) per cycle of one minute, equals 0.99 l x 60 = 660 l/h (NR). ine area cm 2 x 400 cm = cm 3 ine volume cm 3 x (6 bar + atm) x stroke and return = cm 3 (NR) per cycle of one minute, equals 6.33 l x 60 = 380 l/h (NR). Instant air consumption Cylinder area cm 2 x 0 cm = 785 cm 3 Cylinder volume cm 3 x (6 bar + atm) x out stroke = cm 3 (NR) in 0.8 s, equals 5495 l x 60 / 0.8 = 42 l/mn (NR). ine area cm 2 x 400 = cm 3 ine volume cm 3 x (6 bar + atm) x out stroke = 3 65 cm 3 (NR) in 0.8 s, equals 3.6 l x 60/0.8 = 237 l/mn (NR). This example calculation illustrates that in some cases the line volume accounts for more than half the air consumption. In such cases it is important to mount the valve as close as possible to the cylinder. For lowspeed cylinder applications, the use of smaller diameter connecting lines is appropriate. 20 Catalogue 0093-UK

27 Pneumatic connectors design manual Pneumatic system calculations ir consumption for different pneumatic tools Tool Consumption Duty cycle m 3 / h (NR) sec Shears to 0.8 Hammer-action wrenches for : 6mm bolts 7 0. to mm bolts to mm bolts to mm bolts to mm bolts to mm bolts to 0.3 Nibblers to 0.6 Grinders dia. 00 mm to 0.5 dia. 50 mm to 0.5 Grinders/cutters dia. 80 mm to 0.5 dia. 235 mm to 0.5 Drills and nut tappers 6 to 8 mm to to 0 mm to to 3 mm to mm to mm to mm to 0.7 Spray guns 6 to to 0.9 Sanders sander dia to 0.5 sander dia to 0.5 Orbital sanders with disk to 0.9 with pad to 0.9 ellows (2 mm nozzle) 0 0. to 0.2 Screw-driving machines 6 mm to mm to mm to 0.6 2) Pneumatic power units ir compressors are designed with consideration for the overall operational requirements, together with the air demand of the machines and hand tools. When calculating the air demand of pneumatic hand tools, their actual working time should be taken into account. For the associated connecting hose the instant air consumption is also determined. eakage eakage is measured as pressure drop in compressed air systems, and pressure increase in vacuum systems. The respective leak rates are calculated as follows. Units of measurement of leakage - atm = 03.0 mbar = 760 Torr - atm cm 3 /s = 0. Pascal m 3 /s = mbar l/s = 0.76 Torr l/s = 760 usec (litre, micron, second) Calculating leakage in compressed air systems Tank volume : m 3 Initial pressure : 8 bar. Pressure after 2 min 30 s. = 5 bar Pressure drop : 8-5 = 3 bar eak rate = m 3 x 3 bar x 60/2.5 equals 4.4 Nm3/h (NR). Calculating leakage in vacuum systems Tank volume : m 3 Initial vacuum : 0.02 atm. Pressure increase : = atm eak rate = 000 cm 3 x atm x 60/8.5 equals 480 atm. cm 3 /s. Vacuum after 8 min 30 s. : 0.08 atm Pressure increase : = atm eak rate = 000 cm 3 x atm x 60/8.5 equals 480 atm.cm 3 /s eak detection Soap bubble method: hole of 2µm at a pressure of 2 bar produces a bubble of mm 3 per minute. Spray method : Spray type leak testers offer convenience and ease of application. 2 Catalogue 0093-UK

28 Pneumatic connectors design manual Installation guidelines Service lines Steel tubing, copper tubing or metal braid reinforced hoses are used for the connection of air operated machines to the supply network. Connecting lines of unsecured plastic tubing is not recommended (accident hazard in the case of pressure line pull off). Service lines - even copper - must not be used for earthing purposes. Suspended pressure lines For suspended pressure lines, the Parker Push-ok hose system offers easy assembly and alignment, together with a vibration absorbing connection. If the risk of hose pull-off during operation cannot be excluded, the hose must be secured so as to prevent dangerous whippin Pneumatic tubes, even if copper, should not be used for earthing purposes. void problems of alignment and vibration by not linking machines to a joint air supply. 22 Catalogue 0093-UK

29 Pneumatic connectors design manual Installation guidelines Open Closed Wall-mounted pressure lines For wall-mounted connecting lines, copper or steel tubing is preferred to flexible hoses which tend to chafe against the wall. The line is fixed to the wall with tube clamps approx m apart. Open Shut-off and unloading valve shut-off and unloading valve is "in line" mounted at the inlet of each air operated machine. silencer and pressure relief device should be mounted on the outlet of the unloading valve. Closed Parker tube fittings simplify the installation of connections between air operated machinery and supply networks, and facilitate, in particular, transition from copper to plastic tubing or pressure hoses. High temperature or high vibration environment In a high temperature or high vibration environment, the use of hose is recommended. 23 Catalogue 0093-UK

30 Pneumatic connectors design manual Installation guidelines simple bulkhead connection for thin walls. ir preparation equipment The filter regulator lubricator unit is normally mounted at the inlet of the air operated machine, where the drain and filler plugs are easily accessible for maintenance purposes. any pneumatic systems use oil-free control air. For the control line a small tube size is sufficient, because the air demand of the control circuit is minimal. In case of protected control cabinets with built-in air preparation equipment, the end connections for exhaust lines, drainage and, if possible, oil filling, should be located on the outside of the control cabinet. Connecting lines Control units Pressure indicator mounted on a tee Panel mounted pressure indication 24 Catalogue 0093-UK

31 Pneumatic connectors design manual Installation guidelines Pilot lines Power circuit piping in a control cabinet Pressure line Power lines Silencer Stackable connection blocks, top and bottom piping Pilot lines Pressure line Silencer Power lines Stackable connection blocks, rear piping anjo bolt Pressure line ssembly of non-stackable connection blocks (outlets can be linked together using the same assembly method) Exhaust ports can be connected to collecting lines. dequate precautions should be made to ensure that any back pressure does not operate another valve or cylinder. 25 Catalogue 0093-UK

32 Pneumatic connectors design manual Pneumatic control Pneumatic cylinders Service lines for pneumatic cylinders are made using fibre-braid reinforced hose (accident protection in case of pull-off during operation) or flexible polyamide or polyurethane tubin reas exposed to heavy chafing should be sleeved. For interconnections between pneumatic cylinders and air-oil reservoirs, polyamide or polyurethane tubing of appropriate pressure rating should be used. Where air-oil intensifiers are used, pipework should be copper ( no volume expansion during operational pressure surges). Pneumatic integrated fittings Flow control valves Pneumatic integrated regulators are designed for direct mounting onto cylinder ports, securing accurate control of the exhaust air flow from the cylinder, and precise adjustment of piston-rod speed. Their use permits easier piping and a more compact installation. ounting on cylinder Installation in line or where it is difficult to obtain access to the cylinder for adjustment For control of inlet air on mini cylinders 26 Catalogue 0093-UK

33 Pneumatic connectors design manual Pneumatic control Prestobloc check valves Pneumatically controlled Prestobloc check valves are designed for direct mounting onto cylinder ports, and assure the quick stopping of the pistonrod by blocking the cylinder supply and exhaust. The two direction valve is normally open. It closes when the control pressure is cut off, as well as in the event of an air failure. Prestobloc fittings are used, in particular, as safety stops to prevent descent under load in the event of a power failure, and as safety locks associated with emergency switches. Prestoload exhaust valves Pneumatically controlled Prestoload exhaust valves are designed for direct mounting onto cylinder ports and provide a quick discharge of the cylinder chambers upon receipt of a pilot signal. The valve closes when the control pressure is cut off. Prestosil silencers and flow control valves Integrated Prestosil components are designed for direct mounting onto the exhaust port of single acting cylinders and directional control valves. They provide efficient silencing of exhaust noise and permit precise adjustment of piston-rod speed. 27 Catalogue 0093-UK

34 Pneumatic connectors design manual Connectors for pneumatic systems The large variety of pneumatic applications has led to the development of fittings to meet these requirements. There are 3 major fitting styles: - Push-in fittings for application with flexible tubing and pressures up to 25 bar. - Compression fittings for applications with copper and flexible tubin For pressures up to 80 bar. - Push-on fittings suitable for use with flexible tubing and pressures up to 40 bar. Parker offers a complete fitting package for pneumatic applications. Prestolok 2 push-in fittings Prestolok 2 push-in fittings are manufactured from glass reinforced nylon bodies and nickel plated brass stud terminations. They are designed for use with plastic tubing from primary vacuum to 8 bar, and temperatures up to 80 C. pplication examples: - Textile machinery - Packaging equipment - Cutting oils - Robots Prestolok micro push-in fittings Prestolok micro push in fittings are designed for use where space is at a premium. They are designed for use with plastic tubing from primary vacuum to 6 bar, and temperatures up to 80 C. pplication examples: - iniature cylinders - iniature pneumatics Prestoweld 2 push-in fittings Prestoweld 2 brass push-in fittings are used with Prestoweld 2 spark resistant tubing for welding applications. Suitable for use from primary vacuum to 25 bar and temperatures up to 00 C. pplication examples: - Welding guns - Welding fixtures - Spot welding machines Prestolok push-in fittings Prestolok push-in brass fittings are suitable for plastic tubing from primary vacuum to 25 bar, and temperatures up to 00 C pplication examples: - Transfer lines - Compressors - Climate control 28 Catalogue 0093-UK

35 Pneumatic connectors design manual Connectors for pneumatic systems etrulok brass fittings These bite type fittings are suitable for copper tubing up to 80 bar and polyamide tubing up to 42 bar pressure, and temperatures up to 90 C. pplication examples : Compressors, Pneumatic hand tools, ubrication systems, utomotive auxiliary systems. P nickel plated brass fittings P two-piece fully reusable nickel plated brass fittings for use with plastic tubin They can be assembled by hand with polyurethane tubin Suitable for pressures up to 40 bar and temperatures up to 00 C. pplication examples : aboratory equipment, Pneumatic hand tools, Pressure washers, Packaging machinery. rass adaptors comprehensive range of adaptors for pneumatic and low pressure fluid applications. vailable with SPP, metric and NPT threads they may be used from primary vacuum to 60 bar. 2 all Valves Suitable for many fluid applications. Parker s range of SPP threaded ball valves include short and long thread options, mini barstock valves and padlockable valves in sizes up to 2 SPP. 2 2 Pneumatic Quick couplers rass and steel pneumatic quick couplings meeting ISO 650-, ISO 650-C or Europrofile. vailable with different end configurations and flow performance up to 3500 l/min, they can be used for : grinding machines, pneumatic wrenches, tools currently utilised in industry and garages, and also for many other applications. 2 low guns Impact resistant plastic blow guns available with a variety of nozzle configurations with or without safety valvin They can be used at all the manufacturing stages to : blow off parts, clean work-stations, remove dust, dry. Ermeto original - ite Type High Pressure Tube Fitting Systems - EO-2 Dry Technology : Steel with NR sealing for steel tubing or Stainless steel.457 with FP sealing for stainless steel tubin - DPR Progressive Ring : Steel or Stainless Steel.457 for Steel or Stainless Steel tubin -D Cutting Ring : rass for copper or polyamide tubin pplication examples : Compressors, achine tools, Handling Equipment, Injection ouldin 29 Catalogue 0093-UK

36 Pneumatic connectors design manual Terms used in pneumatics bsolute pressure bsolute temperature ctuator diabatic expansion Pressure measured from absolute zero. Temperature measured above absolute zero. pneumatic device which is used to apply power, e. a lever, solenoid or cylinder. The expansion or compression of a gas without change in heat content. Compressor regulator Condensate Discharge temperature Displacement device fitted to a compressor which controls the output of the machine. iquid formed by the condensation of water vapour in the air, due to a fall in temperature. Temperature at the standard discharge point of a compressor. The volume displaced by the compression element in a given time. ftercooling Removal of heat from air after compression is complete. Dryer Equipment used to reduce the water vapour content of compressed air. ir receiver mbient temperature pressure vessel in which compressed air is stored. Temperature of the environment. Fusible plug Fitted to the hot discharge zone of a compressor for protection against excessively high temperatures. tmospheric pressure Capacity (compressor) The absolute pressure of the atmosphere as measured for a given altitude. ctual volume rate of flow, compressed and delivered at the discharge point, at stated inlet conditions. Gauge pressure Inlet temperature Intercooling Pressure measured above or below atmospheric pressure. Temperature at the standard inlet point of the compressor. The cooling of compressed air between compression stages. Closed loop system Compression ratio Compressor pneumatic circuit, whereby, air from the actuators is returned as a closed pressurised circuit to the compressor inlet. Ratio of final pressure to original pressure. machine which causes a gas to flow against a pressure thus converting mechanical force and motion into pneumatic fluid power. Isothermal expansion ulti-stage compression ubricator Expansion or compression without change of temperature. Two or more stages of compression, with intercooling between them, before the final pressure is reached. Equipment used to release a controlled amount of lubricant into the compressed air stream. 30 Catalogue 0093-UK

37 Pneumatic connectors design manual Terms used in pneumatics Overall stage ratio The pressure ratio for any particular pressure stage in a multi-stage compressor. Separator device for removing liquids from compressed air. Pressure ratio (total) Pressure regulator The ratio between the absolute discharge pressure and the absolute inlet pressure. valve or similar device for reducing line pressure to a lower constant value. Single-stage compression Specific energy requirement or power consumption Initial to final pressure in a single step. Input energy requirement per unit of compressed air produced ; or shaft input power per unit of compressor capacity. Pressure relief valve valve used to limit the maximum system pressure, exhausting the compressed air to atmosphere when the required back pressure is exceeded. Standard reference atmosphere The agreed atmosphere to which specification, valves and test results are determined in other atmospheres, are corrected. Pulsation dampener chamber fitted at the inlet or discharge of a reciprocating compressor to remove pulsations and to prevent resonance. Volumetric efficiency Ratio of capacity to displacement of a compressor or vacuum pump. Ring main compressed air or vacuum main which begins and ends at the compressor, or vacuum pump providing every outlet which two possible sources of supply. 3 Catalogue 0093-UK

38 Pneumatic connectors design manual Pneumatic symbols For the design of pneumatic systems a range of standard symbols is used to represent the separate components used in the system. These symbols are defined in ISO 29, S 297 and NFEO4-057 Valve symbols Valve type Normal position Description of valve Symbol 2/2 Closed Two port (2 way) Two position (No exhaust port) 2/2 Open Two port (2-way) Two position (No exhaust port) 2 2 3/2 Closed Three port (3-way) Two position 3 2 3/2 Open Three port (3-way) Two position 3 2 4/2 line, for air inlet Four port (4-way) line, for exhaust Two position 4/3 Neutral mid-position Four port (4-way) (all ports closed) Three position /2 line, for air inlet Five port (4-way) line, for exhaust Two position 2 separate exhausts which can be restricted separately. 5/3 (X) Neutral mid-position Five port (4-way) (all ports closed) Three position 5/3 (Y) Negative mid- Five port (4-way) position inlet, Three position closed cylinder ports, open exhaust ports. 5/3 (Z) Positive mid- Five port (4-way) position cylinder, Three position ports open to air inlet Catalogue 0093-UK

39 Pneumatic connectors design manual Pneumatic symbols ethods of valve actuation Description of actuation Symbol uscular actuation : General symbol (without indication of control type) - by push button - by lever - by pedal echanical actuation : - by plunger or tracer - by spring - by roller - by roller, operating in one direction only. Flow Control Valves Description Throttle valve Flow control valve Simplified symbol (Does not indicate the control method or the state of the valve) Valve allows free flow in one direction but restricted flow in the other. Symbol Non-Return Valves, Shuttle Valves, Quick Exhaust Valves Description of valves Symbol Non-return valve : - free Opens if the inlet pressure is higher than the outlet pressure. - spring loaded Opens if the inlet pressure is greater than the outlet pressure plus the spring pressure. Shuttle valve Quick exhaust valve The inlet port connected to the higher pressure is automatically connected to the outlet port while the other inlet port is closed. When the inlet port is unloaded the outlet port is freely exhausted. 33 Catalogue 0093-UK

40 Pneumatic connectors design manual Pneumatic symbols Pneumatic cylinders Description Symbol Single-acting cylinder - push type Cylinder in which the air pressure operates in one direction only. - pull type Double acting cylinder - with single piston rod Cylinder in which the air pressure operates alternately in both directions (forward and backward strokes) - with double-ended piston rod (though rod) Cylinder with cushion : - with double fixed cushion - with double adjustable cushion Sources of Energy Description Symbol Pressure source Simplified general symbol Electric motor Flow lines and connections Flow line : - working line, return line and feed line - pilot control line - drain or bleed line - flexible pipe Flexible hose, usually connecting moving parts - electric line 34 Catalogue 0093-UK

41 Pneumatic connectors design manual Popular Coupling Designs Parker s Quick Coupling Division manufactures quick couplings to interchange with popular designs that have become accepted standards in the industry today. The actual size chart below can be used to help select Parker Quick Couplings that will interchange with specific nipple designs sizes and performance data. STNDRD ISO 650- EUROPROFIE ISO 650-C SERIES P Series /4-3/8 -/2 PF Series /4 EZ Series /4-3/8 -/2 PE Series 7.2 mm PEF Series 7.2 mm - 0 mm PCF Series /4 E TIP CTU SIZE /2 ody Size 3/8 ody Size 0 mm ody Size /4 ody Size 7.2 mm ody Size /4 ody Size FOW RTE (/IN) ax. operating pressure (bar) Catalogue 0093-UK

42 Prestolok 2 Push-in fitting Catalogue UK

43 Prestolok 2 push-in fitting Index Straight connectors male - SPT F3P - p. 6 male - SPP F4P - p. 6 male - metric F8P - p. 7 female - SPP G4P - p. 7 union HPK - p. 7 unequal union HPK - p elbows adjustable extended male - SPT C63PK - p. 8 adjustable male - SPT C63PK - p. 8 compact adjustable male - SPT C63SPK - p. 8 adjustable male SPP C64PK- p. 9 compact adjustable male - SPP C64SPK - p. 9 adjustable male - metric C68PK - p. 9 compact adjustable male - metric C68SPK - p. 9 union EPK - p. 0 compact plug-in T2ESPK - p. 0 adjustable bulkhead union WE6PK - p. 0 Tees union JPK - p. 0 unequal union JPK - p. adjustable male run - SPT R63PK - p. adjustable male run -SPP R64PK - p. adjustable male run - metric R68PK - p. 2 plug-in branch T2JPK - p. 2 plug-in run T2JJPK - p. 2 adjustable male branch - SPT S63PK - p. 3 adjustable male branch - SPP S64PK - p. 3 adjustable male branch - metric S68PK - p. 3 Y connectors adjustable male bulkhead WYJ6PK - p. 4 union YJPK - p. 4 unequal union YJPK - p. 4 plug-in YJ2PK - p. 4 double union YJ5PK - p. 4 plug-in double YJ52PK - p. 5 double union adjustable male - SPT YJ563PK - p. 5 double union adjustable male - SPP YJ564PK - p. 5 adjustable male SPT YJ63PK - p. 5 adjustable male SPP YJ64PK - p. 6 2 Catalogue UK

44 Prestolok 2 push-in fitting Index anifolds 2 tubes and pressure indicator HS3PK - p. 6 3 tubes J3PK - p. 6 multiple tee J5PK - p. 7 multiple tee J6PK - p. 7 multiple tee adjustable male - SPT J663PK - p. 7 multiple tee adjustable male - SPP J664PK - p. 7 daptors / ccessories protective cap C - p. 8 double male union PK - p. 9 plug FNPK - p. 9 Tube end male adaptor - SPT T23FPK - p. 9 Tube end male adaptor - SPP T24FPK - p. 9 Tube end male adaptor - metric T28FPK - p. 20 tube end reducer TR2PK - p. 20 pressure indicator TS2PK - p. 20 Cartridges p. 2 and 22 Complementary parts with brass body Please consult Prestolok section (D) Technical tubing Please consult Thermoplastic single tubes and Pneumo-Tube bundles section (P) 3 Catalogue UK

45 Prestolok 2 push-in fitting Prestolok 2 : push-in fitting for pneumatic applications Principle For a number of years Parker Hannifin has designed and manufactured push-in fittings recognised worldwide for their quality and reliability. The new generation Prestolok 2 has been developed to provide even better technical features for the end user With this additional new product, Parker provides the solutions in many fields and applications. Prestolok 2 uses elastic teeth grab ring technology, invented and perfected by Parker, who guarantee its excellent tube retention qualities. Prestolok 2 can be used with most types of plastic tubing available on the market (see Thermoplastic single tube and Pneumo-Tube bundles section - P*), offering significant advantages to the user. * For other materials, please consult us. 2 8 Technical features aterial ody Threaded Sleeve Grab ring Push ack-up O-ring Protective straight connectors button washer cap Polyamide HR Nickel Nickel Stainless Polyacetal rass Nitrile Polyacetal plated plated steel brass brass Working pressure From 0.0 to 8 bar Working temperature From - 25 C to + 80 C pplications Perfectly adapted for use with pneumatic systems in a large variety of industries, Prestolok 2 is also designed to handle many other fluids (please consult us) thus covering a wide range of applications. Textile achine tools Packaging Food industrie Robotics 4 Catalogue UK

46 Prestolok 2 push-in fitting dvantages Ready-to-use compact fitting Wide product range covering all applications Full flow capability Protective cap The design of the Prestolok 2 thermoplastic range permits the use of a protective cap for following functions : protection : prevents the ingress of dirt into the connection system, safety: eliminates the risk of accidental disconnnection, as the push-button is made inaccessible, identification : - colour coding allows identification of fluid lines, - tube sizes are marked on the protective cap. High resistance polyamide body The use of UV-resistant reinforced polyamide provides : - weight saving, - excellent mechanical performance, - compact design. The three grooves facilitate handling and positioning of elbows and tees. long service life is ensured by the corrosion free body material. Ready-to-use fitting The Prestolok 2 range is manufactured with brass nickel plated male threads ready for use : - parallel threads are supplied with a pre-assembled, fully retained O-ring seal, - taper threads are treated with a special PTFE for self sealing on assembly, reusable up to five times without additional sealing material. Positive hold by a flexible grab ring - the special shape of the radial teeth grab ring prevents longditudinal scratch marks on the tube. - the elasticity of the grab ring absorbs vibration and pulsating pressure. -a twist-free assembly, the tube can rotate freely even under pressure. How to use Positive O-ring sealing - the smooth unmarked tube is in direct contact with the nitrile O-ring, giving a positive seal. -a unique back-up washer retains the O-ring in the optimum sealing position, protects it from the grab ring, and prevents extrusion under pressure. Plastic push button - simple manual pressure on the user friendly push button allows instant disconnection of the tube. - tube sizes are marked on the push button for easy identification. ssembly - Cut the tube square. - Insert the tube into the fitting until it bottoms. Disassembly - Simply press on the push button and withdraw the tube 5 Catalogue UK

47 Prestolok 2 push-in fitting F3P - ale connector - SPT C4 Threads are treated with PTFE sealing material F4P - ale connector - SPP P PTFE Part number C4 P H. Weight Int. 4 /8 F3P4-/ /4 F3P4-/ /8 F3P5-/ /4 F3P5-/ /8 F3P6-/ /4 F3P6-/ /8 F3P8-/ /4 F3P8-/ /8 F3P8-3/ /4 F3P0-/ /8 F3P0-3/ /2 F3P0-/ /4 F3P2-/ /8 F3P2-3/ /2 F3P2-/ /8 F3P4-3/ /2 F3P4-/ C 4 J Part number C4 J H. Weight Int. 4 /8 F4P4-/ /4 F4P4-/ /8 F4P6-/ /4 F4P6-/ /8 F4P8-/8* /4 F4P8-/ /8 F4P8-3/ /4 F4P0-/ /8 F4P0-3/ /2 F4P0-/ /4 F4P2-/ /8 F4P2-3/8* /2 F4P2-/ /8 F4P4-3/ /2 F4P4-/ * no protective cap facility ll straight male connectors have an internal hexagon for use with an llen key to allow the fitting to be mounted in any position. This also permits close porting not possible when a spanner is used. 6 Catalogue UK

48 F8P - ale connector - metric straight thread Prestolok 2 push-in fitting Part number C4 J H. Weight Int. C 4 J 4 5x0.8 F8P x F8P x0.8 F8P x F8P x.5 F8P x.5 F8P x.5 F8P x.5 F8P G4P - Female connector - SPP C 4 J Part number C4 J Weight 4 /8 G4P4-/ /8 G4P6-/ /4 G4P6-/ /8 G4P8-/ /4 G4P8-/ HPK - Equal union Part number O Weight O 4 HPK HPK HPK HPK HPK HPK HPK - Unequal union 2 O 2 Part number O Weight 6 4 HPK HPK HPK HPK HPK HPK Catalogue UK

49 Prestolok 2 push-in fitting C63PK - djustable extended male elbow - SPT 3 Part number C4 N O P Width Weight dia. Q O ø 3xQ N /8 C63PK4-/ /4 C63PK4-/ /8 C63PK6-/ /4 C63PK6-/ /8 C63PK8-/ C4 P /4 C63PK8-/ PTFE Threads are treated with PTFE sealing material C63PK - djustable male elbow - SPT O ø 3xQ N C4 P PTFE Threads are treated with PTFE sealing material 3 Part number C4 N O P Width Weight dia. Q /8 C63PK4-/ /4 C63PK4-/ /8 C63PK6-/ /4 C63PK6-/ /8 C63PK8-/ /4 C63PK8-/ /8 C63PK8-3/ /4 C63PK0-/ /8 C63PK0-3/ /2 C63PK0-/ /4 C63PK2-/ /8 C63PK2-3/ /2 C63PK2-/ /8 C63PK4-3/ /2 C63PK4-/ C63SPK - Compact adjustable male elbow - SPT O H C4 P PTFE Threads are treated with PTFE sealing material Part number C4 H O P Weight 4 /8 C63SPK4-/ /4 C63SPK4-/ /8 C63SPK6-/ /4 C63SPK6-/ /8 C63SPK8-/ /4 C63SPK8-/ /8 C63SPK8-3/ /4 C63SPK0-/ /8 C63SPK0-3/ /2 C63SPK0-/ Our fittings are supplied without cap. See page- 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 8 Catalogue UK

50 C64PK - djustable male elbow - SPP Prestolok 2 push-in fitting 3 Part number C4 J N O Width Weight dia. Q O /8 C64PK4-/ /4 C64PK4-/ /8 C64PK6-/ /4 C64PK6-/ /8 C64PK8-/ ø 3xQ C4 J N /4 C64PK8-/ /8 C64PK8-3/ /4 C64PK0-/ /8 C64PK0-3/ /4 C64PK2-/ /8 C64PK2-3/ /8 C64PK4-3/ /2 C64PK4-/ C64SPK - Compact adjustable male elbow - SPP Part number C4 H J O Weight O C 4 H J 4 /8 C64SPK4-/ /4 C64SPK4-/ /8 C64SPK6-/ /4 C64SPK6-/ /8 C64SPK8-/ /4 C64SPK8-/ /8 C64SPK8-3/ C68PK - djustable male elbow - metric straight thread 3 Part number C4 J N O Width Weight dia. Q O ø 3xQ C4 J N x0.5 C68PK x0.8 C68PK x0.8 C68PK x.5 C68PK x.5 C68PK x.5 C68PK x.5 C68PK C68SPK - Compact adjustable male elbow - metric straight Part number C4 H J O Weight O H 4 5x0.8 C68SPK C 4 J Our fittings are supplied without cap. See page- 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 9 Catalogue UK

51 Prestolok 2 push-in fitting EPK - Equal union elbow 3 Part number O Width Weight dia. Q O ø 3xQ EPK EPK EPK EPK EPK EPK T2ESPK - Compact plug-in elbow 2 Part number H H H2 O Weight O 2 H2 H H 4 4 T2ESPK T2ESPK T2ESPK T2ESPK WE6PK - 90 adjustable bulkhead union elbow 3 Part number C C4 O Width W Weight dia. Q ax. ø 3xQ C W x0.75 WE6PK x WE6PK x.25 WE6PK x WE6PK x.5 WE6PK C4 O JPK - Equal union tee O ø 3xQ 3 Part numbe r O Width Weight dia. Q JPK JPK JPK JPK JPK JPK Catalogue UK

52 Prestolok 2 push-in fitting JPK - Unequal union tee 2 3 Part number O Width Weight dia. Q JPK JPK JPK JPK JPK O ø 3xQ JPK JPK JPK R63PK - djustable male run tee - SPT 3 Part number C4 N O P Width Weight dia. Q O N P PTFE /8 R63PK4-/ /4 R63PK4-/ /8 R63PK6-/ /4 R63PK6-/ /8 R63PK8-/ C4 ø 3xQ Threads are treated with PTFE sealing material /4 R63PK8-/ /8 R63PK8-3/ /4 R63PK0-/ /8 R63PK0-3/ /4 R63PK2-/ /8 R63PK2-3/ /2 R63PK2-/ /8 R63PK4-3/ /2 R63PK4-/ R64PK - djustable male run tee - SPP 3 Part number C4 J N O Width Weight dia. Q /8 R64PK4-/ /4 R64PK4-/ /8 R64PK6-/ /4 R64PK6-/ /8 R64PK8-/ O N J C4 ø 3xQ /4 R64PK8-/ /8 R64PK8-3/ /4 R64PK0-/ /8 R64PK0-3/ /4 R64PK2-/ /8 R64PK2-3/ /8 R64PK4-3/ /2 R64PK4-/ Our fittings are supplied without cap. See page- 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. Catalogue UK

53 Prestolok 2 push-in fitting R68PK - djustable male run tee - metric straight thread O N J 3 Part number C4 J N O Width Weight dia. Q x0.5 R68PK x0.8 R68PK x0.8 R68PK x.5 R68PK x.5 R68PK C4 ø 3xQ x.5 R68PK T2JPK - Plug-in branch tee 2 3 Part number H N O Width Weight dia. Q O T2JPK T2JPK T2JPK ø 3xQ N H 2 T2JJPK - Plug-in run tee N H 2 3 Part number H N O Width Weight dia. Q O ø 3xQ T2JJPK T2JJPK T2JJPK Our fittings are supplied without cap. See page- 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 2 Catalogue UK

54 S63PK - djustable male branch tee - SPT Prestolok 2 push-in fitting 3 Part number C4 N O P Width Weight dia. Q O /8 S63PK4-/ /4 S63PK4-/ /8 S63PK6-/ /4 S63PK6-/ /8 S63PK8-/ ø 3xQ C4 PTFE P N /4 S63PK8-/ /8 S63PK8-3/ /4 S63PK0-/ /8 S63PK0-3/ /4 S63PK2-/ Threads are treated with PTFE sealing material /8 S63PK2-3/ /2 S63PK2-/ /8 S63PK4-3/ /2 S63PK4-/ S64PK - djustable male branch tee - SPP 3 Part number C4 J N O Width Weight dia. Q O /8 S64PK4-/ /4 S64PK4-/ /8 S64PK6-/ /4 S64PK6-/ /8 S64PK8-/ N J ø 3xQ C /4 S64PK8-/ /8 S64PK8-3/ /4 S64PK0-/ /8 S64PK0-3/ /4 S64PK2-/ /8 S64PK2-3/ /8 S64PK4-3/ /2 S64PK4-/ S68PK - djustable male branch tee - metric straight thread 3 Part number C4 J N O Width Weight dia. Q x0.5 S68PK x0.8 S68PK x0.8 S68PK x.5 S68PK x.5 S68PK N ø 3xQ O J C x.5 S68PK Our fittings are supplied without cap. See page- 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 3 Catalogue UK

55 Prestolok 2 push-in fitting WYJ6PK - djustable male bulkhead Y connector 3 Part number C C4 2 Width U W Weight dia. Q axi 4 x WYJ6PK x 4.2 WYJ6PK x WYJ6PK YJPK - Union Y connector 3 Part number 2 Width U Weight dia. Q U YJPK YJPK YJPK YJPK Ø3xQ YJPK - Unequal union Y connector 2 3 Part number 2 Width U Weight dia. Q U YJPK YJPK YJPK Ø3xQ YJ2PK - Plug-in Y connector 3 3 Part number 2 3 Width U Weight dia. Q U YJ2PK YJ2PK YJ2PK YJ2PK Ø3xQ YJ5PK - Union double Y connector 2 3 Part number 2 Width U Weight dia. Q U YJ5PK YJ5PK Ø3xQ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 4 Catalogue UK

56 YJ52PK - Plug-in double Y connector Prestolok 2 push-in fitting 2 3 Part number 2 Width U Weight dia. Q YJ52PK U 2 2 Ø3xQ YJ563PK - Union double Y connector adjustable male - SPT P 3 Part number C4 2 P Width U Weight dia. Q /8 YJ563PK4-/ /4 YJ563PK4-/ U 2 PTFE C4 Ø3xQ Threads are treated with PTFE sealing material YJ564PK - Union double Y connector adjustable male - SPP 3 Part number C4 J 2 Width U Weight dia. Q J 4 /8 3.2 YJ564PK4-/ /4 3.2 YJ564PK4-/ U 2 C4 Ø3xQ YJ63PK - djustable male Y connector - SPT P 3 Part number C4 2 P Width U Weight dia. Q U 2 PTFE C4 Ø3xQ Threads are treated with PTFE sealing material 4 /8 3.2 YJ63PK4-/ /4 3.2 YJ63PK4-/ /8 4.2 YJ63PK6-/ /4 4.2 YJ63PK6-/ /8 4.2 YJ63PK8-/ /4 4.2 YJ63PK8-/ /4 4.2 YJ63PK0-/ /8 4.2 YJ63PK0-3/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 5 Catalogue UK

57 Prestolok 2 push-in fitting YJ64PK - djustable male Y connector - SPP U J C4 Ø3xQ 2 3 Part number C4 J 2 Width U Weight dia Q 4 /8 3.2 YJ64PK4-/ /4 3.2 YJ64PK4-/ /8 4.2 YJ64PK6-/ /4 4.2 YJ64PK6-/ /8 4.2 YJ64PK8-/ /4 4.2 YJ64PK8-/ /4 4.2 YJ64PK0-/ /8 4.2 YJ64PK0-3/ HS3PK - anifold for 2 tubes and pressure indicator Part number X Weight 4 HS3PK HS3PK HS3PK X J3PK - anifold for 3 tubes Part number X Weight 4 J3PK J3PK J3PK X anifolds Prestolok manifolds permit close porting and compact modular assemblies on mounting rails, irrespective of : - the DIN profiles used : T (32x5x.5), T3 (35x5x.5), T3 (35x7.5x). - the desired manifold configuration (3 tube connections, or 2 tube connections + pressure indicator). - the tube O.D. (4, 6 or 8 mm). 6 Catalogue UK

58 Prestolok 2 push-in fitting J5PK - ultiple tee 2 3 Part number H N Width Weight dia. Q H ø 3xQ J5PK J5PK J5PK J5PK N N J6PK - ultiple tee 2 3 Part number H N Width Weight dia. Q H ø 3xQ J6PK J6PK J6PK J6PK N N N J663PK - djustable male multiple tee - SPT H C4 P Ø3xQ PTFE 2 3 Part number C4 H N P Width Weight dia. Q /8 J663PK6-4-/ /4 J663PK6-4-/ /8 J663PK8-4-/ /4 J663PK8-4-/ /8 J663PK8-4-3/ N N N Threads are treated with PTFE sealing material /8 J663PK8-6-/ /4 J663PK8-6-/ /8 J663PK8-6-3/ /4 J663PK0-6-/ /8 J663PK0-6-3/ J664PK - djustable male multiple tee - SPP 2 3 Part number C4 H J N Width Weight dia. Q H J ø 3xQ C /8 J664PK6-4-/ /4 J664PK6-4-/ /8 J664PK8-4-/ /4 J664PK8-4-/ /8 J664PK8-4-3/ N N N /8 J664PK8-6-/ /4 J664PK8-6-/ /8 J664PK8-6-3/ /4 J664PK0-6-/ /8 J664PK0-6-3/ Catalogue UK

59 Prestolok 2 push-in fitting ultiple tees can be used as a simple system for air distribution. The flow path through the tee is designed to ensure an adequate air supply to the secondary lines. This economic modular concept provides a fully flexible solution for your pneumatic system. C - Protective cap The design of Prestolok 2 permits the use of a protective cap for the following functions : - protection : prevents the ingress of dirt into the connection system, - safety : eliminates the risk of accidental disconnection, as the push button is made inaccessible, - identification : colour coding allows identification of fluid lines, tubes sizes are marked on the protective cap. Part number Weight 4 C4 a) 6 C6 a) 8 C8 a) 0 C0 a) 2 C2 a) 4 C4 a) a) : dd the following code, corresponding to the chosen colour : W : white; U : blue; G : green; R : red; Y : yellow; : black. Example : cap red suitable for tube ø4 mm = C4R. In case of no colour specification, we will deliver yellow caps (standard colour). Our fittings are supplied without cap. Cap must be ordered separately. 8 Catalogue UK

60 Prestolok 2 push-in fitting PK - Double male union Part number Weight 4 PK PK6 4 8 PK8 4 0 PK PK PK FNPK - Plug Part number Weight 4 FNPK FNPK FNPK FNPK FNPK FNPK T23FPK - Tube end male adaptor - SPT PTFE P C4 Threads are treated with PTFE sealing material N T24FPK - Tube end male adaptor - SPP Part number C4 N P Weight 4 /8 T23FPK4-/ /4 T23FPK4-/ /8 T23FPK6-/ /4 T23FPK6-/ /8 T23FPK8-/ /4 T23FPK8-/ /8 T23FPK8-3/ /4 T23FPK0-/ /8 T23FPK0-3/ /2 T23FPK0-/ * Thermoplastic stem with brass nickel plated threads. J N Part number C4 J N Weight 4 /8 T24FPK4-/ /4 T24FPK4-/ /8 T24FPK6-/ /4 T24FPK6-/ /8 T24FPK8-/ C4 8 /4 T24FPK8-/ /8 T24FPK8-3/ /4 T24FPK0-/ /8 T24FPK0-3/ /2 T24FPK0-/ * Thermoplastic stem with brass nickel plated threads. Our fittings are supplied without cap. See page 8 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 9 Catalogue UK

61 Prestolok 2 push-in fitting T28FPK - Tube end male adaptor-metric straight thread J N Part number C4 J N Weight 4 5X0.8 T28FPK X0.8 T28FPK * Thermoplastic stem with brass nickel plated threads. C4 TR2PK - Tube end reducer 2 Part number Weight 4 6 TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TR2PK TS2PK - Pressure indicator Part number Weight 4 TS2PK TS2PK TS2PK For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 20 Catalogue UK

62 Prestolok 2 push-in fitting Cartridges Prestolok cartridge fittings Prestolok compact drive-in cartridge fittings for plastic tubes, are designed for use in pneumatic components for low-pressure applications. They eliminate the need for threaded ports in system components, and allow the construction of spacesaving assemblies. Simple stepped holes are sufficient to receive these cartridges, which are available in tube outer diameters from 4 mm to 2 mm. Prestolok compact drive-in cartridges can be fitted into pneumatic components made of non-ferrous metals (brass, aluminium, zinc-aluminium alloy), and most industrial plastics. They are particularly suitable for the mass production of pneumatic components. For more information on potential applications, please consult your Parker sales engineer. Stepped hole for cartridge reception Depending upon the component material used, the stepped holes for the reception of the drive-in cartridges are obtained by drilling or injection mouldin Dimensions and tolerances are defined by the configuration of the cartridge. For this purpose, we supply stepped drilling tools corresponding to each cartridge type. Technical information available on request. 2 Catalogue UK

63 Prestolok 2 push-in fitting Cartridges Cartridge assembly Prestolok compact drive-in cartridges are installed using a simple tool (one tool for each cartridge size) Position the mandrel above the port. 2 - Insert cartridge with drive-in tool. 3 - Remove mandrel from fitted cartridge. 4 - Insert push sleeve into cartridge. 5 - Final cartridge and tube assembly. Packaging Prestolok drive-in cartridges are supplied in packs of 200 or 250 units (depending on the part number) stored in stacked thermoplastic packing trays. This prevents damage during shipment and simplifies stock control and product handlin Dimensions shown may be changed at any time without prior notice. 22 Catalogue UK

64 Prestolok micro Catalogue UK

65 Prestolok micro Index Straight connectors male - SPT male - metric internal hexagon internal hexagon male - SPT male - SPP male - metric F23P - p. C 7 F28P - p. C 7 F3P - p. C 7 F4P - p. C 7 F8P - p. C 8 C female - SPP female - metric equal union unequal union equal bulkhead G4P - p. C 8 G8P - p. C 8 HPK - p. C 8 HPK - p. C 8 WP - p. C 9 90 elbows adjustable extended adjustable adjustable extended adjustable adjustable extended male - SPT male - SPT male - SPP male - SPP male - metric C63PK - p. C 9 C63PK - p. C 9 C64PK - p. C 9 C64PK - p. C 0 C68PK - p. C 0 adjustable equal union male metric equal union with mounting hole compact plug-in C68PK - p. C 0 EPK - p. C 0 EPFK - p. C T2ESPK - p. C Tees equal union adjustable male run adjustable male run equal union with mounting holes SPT SPP JPK - p. C JPFK - p. C R63PK - p. C 2 R64PK - p. C 2 adjustable male run adjustable male adjustable male adjustable male metric branch - SPT branch - SPP branch - metric R68PK - p. C 2 S63PK - p. C 2 S64PK - p. C 3 S68PK - p. C 3 C 2 Catalogue UK

66 Prestolok micro Index Y connectors equal union equal union unequal union with mounting holes equal - plug-in YJPK - p. C 3 YJPK - p. C 3 YJPFK - p. C 4 YJ2PK - p. C 4 C adjustable male adjustable male unequal - plug-in SPT metric YJ2PK - p. C 4 YJ63PK - p. C 4 YJ68PK - p. C 5 anjos single assembled COR8P - p. C 5 daptors / ccessories plug tube end expander tube end reducer FNPK - p. C 5 TE2PK - p. C 5 TR2PK - p. C 6 tube end male adaptor tube end male adaptor tube end male adaptor SPT SPP metric T23FP - p. C 6 T24FP - p. C 6 T28FP - p. C 6 Technical tubing Please consult Thermoplastic single tubes and Pneumo-Tube bundles section (P). C 3 Catalogue UK

67 Prestolok micro Prestolok micro : push-in fitting for miniature pneumatic applications Principle To provide the fitting solution for miniature pneumatic applications Parker has introduced a new range of instant fittings, Prestolok micro. This complementary product range has been specifically developed to provide the perfect connection for small diameter tubing used in many industries and applications. This new fitting benefits from the constant improvements that Parker has brought to the instant fitting market. Prestolok micro uses "elastic teeth" stainless steel grab ring technology. This system invented by Parker and developed through previous generations of Prestolok fittings provides perfect tube retention without damaging the tube, thus guaranteeing a leak free connection. Prestolok micro is designed for use with Parker calibrated polyamide and polyurethane tubing (see Thermoplastic single tube and Pneumo-Tube bundles section - P*) C * For other materials, please consult us. Technical features aterial ody Threaded parts Sleeve Grab ring Push O-Ring button Polyamide Nickel plated rass (Npb for Stainless Polyacetal Nitrile HR brass straight connect.) steel Working pressure From 0.0 to 6 bar Working temperature From - 25 C to + 80 C pplications Prestolok micro is designed to reduce space, save weight and time during assembly and bring a cost effective solution for all applications. Prestolok micro can be a real economy. Prestolok micro's unique characteristics make it the perfect connector for miniature pneumatic systems in a wide range of applications. Packaging Precision machinery Ink marking Developed for use with pneumatic systems in a wide variety of industries, Prestolok micro is designed to convey many other fluids (please consult us) thus covering a broad range of applications. achine tools Food industry Textile utomotive Robotics C 4 Catalogue UK

68 Prestolok micro dvantages Wide product range suitable for many applications. Nickel plated brass adaptors. Full flow capacity. C Perfect miniaturisation. The Prestolok micro concept offers : an ergonomic shape with small dimensions but allowing for excellent handling and manipulation of the fitting, compact dimensions allow efficient utilisation in applications where space is a decisive factor, reduced size and weight which, are very important when used with unsupported pipe runs, excellent flow characteristics give minimal pressure drop. multi-functional push-button. the new push button design encapsulates the fitting body to prevent contamination, the profile of the push button enables simple and efficient disconnection of the tube, the marking of the tube diameter and the optional choice of colour on the push button enable simple identification of circuits, it ensures a uniform distribution of the pushing force for easy disconnection. the one piece design makes the push button unlosable. Ready-to-use fitting the Prestolok micro range of fittings is manufactured ready to use, saving time and reducing assembly costs : taper threads are treated with a special PTFE. This factory applied treatment enables the fitting to be connected and disconnected up to five times without additional treatment, fittings with parallel threads are supplied with a pre-assembled fully retained O-ring ensuring a perfect seal. Positive retention with a flexible grab rin this system, invented, developed and perfected by Parker, guarantees excellent tube retention, the special radial shape of the teeth of the grab ring do not damage the tube or affect the sealing, the elasticity of the grab ring absorbs all vibration and impulsing, the design of the grab ring allows the tube to rotate freely even under pressure. High resistance polyamide body. The use of high resistance polyamide offers : excellent mechanical characteristics (robustness), high corrosion resistance, UV resistant polymers guarantee a long service life. ounting holes on shaped fittings. On request, union connectors can be supplied equipped with mounting holes. This option permits : mounting in banks for compact installations and simplified pipework, facility for mounting on frames or panels, greater flexibility and additional space savin C 5 Catalogue UK

69 Prestolok micro Instructions for use ssembly : Prestolok micro must only be used with calibrated polyamide (in accordance with DIN 73378, S 5409 Part 2, NF E49-00, CETOP RP45) and polyurethane (in accordance with NF E49-0) tubing conforming to standards shown in Thermoplastic single tubes and Pneumo-Tube bundles section (P). For other tubing materials please consult us. C ssembly torque Thread 3 5 G/8 G/4 max. Torque m. da N Cut the tube square For threaded fittings, tighten to the recommended assembly torque. Insert the tube into the fitting until it bottoms. Disassembly : Simply press on the push button and withdraw the tube. F23P and F28P straight male connectors have an internal hexagon for use with an llen key to allow the fitting to be mounted in any position. This also permits close porting not possible when a spanner is used. C 6 Catalogue UK

70 Prestolok micro F23P - ale connector - SPT E PTFE R P internal hex Part number E P R Int. H 3 /8 F23P3-/ /8 F23P4-/ /8 F23P6-/ This fitting has been designed for use where space is at a premium. It is assembled using the internal hexagon and an llen key. Weight C Threads are treated with PTFE sealing material. F28P - ale connector - metric straight thread Part number E J N Int. H Weight E N J 3 3x0.5 F28P x0.8 F28P x0.5 F28P x0.8 F28P x0.8 F28P This fitting has been designed for use where space is at a premium. It is assembled using the internal hexagon and an llen key. F3P - ale connector - SPT Part number C P R Weight E R PTFE 4 /8 F3P4-/ /4 F3P4-/ /8 F3P6-/ /4 F3P6-/ C P Threads are treated with PTFE sealing material. F4P - ale connector - SPP Part number C E J N Weight E N J 4 /8 F4P4-/ /4 F4P4-/ /8 F4P6-/ /4 F4P6-/ C For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 7 Catalogue UK

71 Prestolok micro F8P - ale - metric straight thread E C N J Part number C E J N Weight 3 3x0.5 F8P x0.8 F8P x0.5 F8P x0.8 F8P x0.8 F8P C G4P - Female - SPP E J C Part number C E J Weight 4 /8 G4P4-/ /4 G4P4-/ /8 G4P6-/ /4 G4P6-/ G8P - Female - metric E J C Part number C E J Weight 3 3x0.5 G8P x0.8 G8P x0.5 G8P x0.8 G8P HPK - Equal union 2 Part number E Weight E HPK HPK HPK HPK - Unequal union 2 Part number E Weight 4 3 HPK HPK E 2 For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 8 Catalogue UK

72 Prestolok micro WP - ulkhead equal union W Part number C W maxi. Weight 3 8x WP x WP x WP C C C C63PK - djustable extended male elbow - SPT Part number C E P R Weight E C P R 3 /8 C63PK3-/ /8 C63PK4-/ /4 C63PK4-/ /8 C63PK6-/ /4 C63PK6-/ PTFE Threads are treated with PTFE sealing material. C63PK - djustable male elbow - SPT Part number C E P R Weight E P C R 3 /8 C63PK3-/ /8 C63PK4-/ /4 C63PK4-/ /8 C63PK6-/ /4 C63PK6-/ PTFE Threads are treated with PTFE sealing material. C64PK - djustable extended male elbow - SPP Part number C E J N Weight E C N 4 /8 C64PK4-/ /4 C64PK4-/ /8 C64PK6-/ /4 C64PK6-/ J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 9 Catalogue UK

73 Prestolok micro C64PK - djustable male elbow - SPP E C N J Part number C E J N Weight 4 /8 C64PK4-/ /4 C64PK4-/ /8 C64PK6-/ /4 C64PK6-/ C C68PK - djustable extended male elbow - metric straight Part number C E J N Weight E C N 3 3x0.5 C68PK x0.8 C68PK x0.5 C68PK x0.8 C68PK x0.8 C68PK J C68PK - djustable male elbow - metric straight thread E C N J Part number C E J N Weight 3 3x0.5 C68PK x0.8 C68PK x0.5 C68PK x0.8 C68PK x0.8 C68PK EPK - Equal elbow Part number E Weight 3 EPK EPK EPK E For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 0 Catalogue UK

74 Prestolok micro EPFK - Equal elbow with mounting hole Ø3xQ S S Part number E Ø 3 Q S Weight 3 EPFK EPFK EPFK Not available from stock, please consult us. C E T2ESPK - Compact plug-in elbow 2 Part number E H Weight E H 3 3 T2ESPK T2ESPK T2ESPK T2ESPK T2ESPK JPK - Equal tee Part number E Weight 3 JPK JPK JPK E JPFK - Equal tee with mounting holes Ø3xQ S S S Part number E Ø 3 Q S Weight 3 JPFK JPFK JPFK Not available from stock, please consult us. E For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C Catalogue UK

75 Prestolok micro R63PK - djustable male run tee - SPT R PTFE Part number C E P R Weight C P 3 /8 R63PK3-/ /8 R63PK4-/ /4 R63PK4-/ /8 R63PK6-/ /4 R63PK6-/ C E Threads are treated with PTFE sealing material. R64PK - djustable male run tee - SPP N J Part number C E J N Weight C 4 /8 R64PK4-/ /4 R64PK4-/ /8 R64PK6-/ /4 R64PK6-/ E R68PK - djustable male run tee - metric straight thread N J C Part number C E J N Weight 3 3x0.5 R68PK x0.8 R68PK x0.5 R68PK x0.8 R68PK x0.8 R68PK E S63PK - djustable male branch tee - SPT Part number C E P R Weight E P C R 3 /8 S63PK3-/ /8 S63PK4-/ /4 S63PK4-/ /8 S63PK6-/ /4 S63PK6-/ PTFE Threads are treated with PTFE sealing material. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 2 Catalogue UK

76 Prestolok micro S64PK - djustable male branch tee - SPP E C N J Part number C E J N Weight 4 /8 S64PK4-/ /4 S64PK4-/ /8 S64PK6-/ /4 S64PK6-/ C S68PK - djustable male branch tee - metric straight thread E C N J Part number C E J N Weight 3 3x0.5 S68PK x0.8 S68PK x0.5 S68PK x0.8 S68PK x0.8 S68PK YJPK - Equal Y union 2 Part number 2 Weight 3 3 YJPK YJPK YJPK YJPK - Unequal Y union 2 Part number 2 Weight 3 4 YJPK YJPK YJPK For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 3 Catalogue UK

77 Prestolok micro YJPFK - Y union with mounting holes Part number 2 Ø 3 Q S T Weight 2 T S S 3 YJPFK YJPFK YJPFK Not available from stock, please consult us. C Ø3xQ YJ2PK - Equal plug-in Y union H Part number H 2 Weight 3 3 YJ2PK YJ2PK YJ2PK YJ2PK - Unequal plug-in Y union H 2 Part number H 2 Weight 4 3 YJ2PK YJ2PK YJ63PK - djustable male Y connector - SPT 2 R PTFE Part number C 2 P R Weight 3 /8 YJ63PK3-/ /8 YJ63PK4-/ /8 YJ63PK6-/ C P Threads are treated with PTFE sealing material. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 4 Catalogue UK

78 Prestolok micro YJ68PK - djustable male Y connector - metric straight thread Part number C J 2 N Weight 2 N J C 3 3x0.5 YJ68PK x0.8 YJ68PK x0.8 YJ68PK C COR8P - anjo - metric straight thread C4 Part number C4 E J K N T Weight 3 3x0.5 COR8P x0.8 COR8P E J K T N FNPK - Plug Weight Part number 3 FNPK3 22 TE2PK - Tube end expander Weight 2 Part number 6 4 TE2PK For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 5 Catalogue UK

79 Prestolok micro TR2PK - Tube end reducer Weight 2 Part number 3 4 TR2PK C T23FP - Tube end male adaptor - SPT R H PTFE Part number C H P R Weight 4 /8 T23FP4-/ /4 T23FP4-/ /8 T23FP6-/ /4 T23FP6-/ C P Threads are treated with PTFE sealing material. T24FP - Tube end male adaptor - SPP H O Part number C H J O Weight 4 /8 T24FP4-/ /4 T24FP4-/ /8 T24FP6-/ /4 T24FP6-/ C J T28FP - Tube end male adaptor - metric H O Part number C H J O Weight 3 3x0.5 T28FP x0.8 T28FP C J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C 6 Catalogue UK

80 Prestolok Push-in fitting for fluids Catalogue UK

81 Prestolok push-in fitting Index Straight connectors male - SPT F23P - p. D 6 male - metric F28P - p. D 6 male - SPT F3P - p. D 6 male - NPTF FP - p. D 6 D male - SPP F4P - p. D 7 male - metric F8P - p. D 7 female - SPP G4P - p. D 8 equal union HP - p. D 8 ulkhead unions C 2 W C J 2 female - SPP WG4P - p. D 8 mixed WP - p. D 8 equal WP - p. D 9 90 elbows compact - SPT C3P - p. D 9 adjustable male NPTF C6P - p. D 9 adjustable extended male - SPT C63P - p. D 9 adjustable male SPT C63P - p. D 0 adjustable male SPP C64P - p. D 0 compact adjustable male - SPP C64SP - p. D 0 adjustable male - metric C68P - p. D compact adjustable male - metric C68SP - p. D equal union EP - p. D adjustable bulkhead union WE6P - p. D Tees equal union JP - p. D 2 adjustable male run - SPT R63P - p. D 2 adjustable male run - SPP R64P - p. D 2 adjustable male run - metric R68P - p. D 3 adjustable male branch - SPT S63P - p. D 3 adjustable male branch - SPP S64P - p. D 3 adjustable male branch - metric S68P - p. D 3 D 2 Catalogue UK

82 Prestolok push-in fitting Index anjos single - body only CORP - p. D 4 double - body only CORPD - p. D 4 single - assembled COR8P/COR4P - p. D 4 double - assembled COR8PD/COR4PD - p. D 5 D single bolt with seals SC8U/SC4U - p. D 5 stacking bolt with seals SC8UD/SC4UD - p. D 5 daptors/ ccessories plug FNP - p. D 6 tube end expander TEP - p. D 6 tube end reducer TRP - p. D 6 tube end male adaptor SPT T23HFP - p. D 6 Complementary parts with thermoplastic body Technical tubing Please consult Prestolok 2 section () Please consult Thermoplastic single tubes and Pneumo-Tube bundles section (P) D 3 Catalogue UK

83 Prestolok push-in fitting Prestolok : push-in fitting for fluid and arduous pneumatic applications Principle For more than 20 years, Parker Hannifin has designed and manufactured push-in fittings recognised worldwide for their quality and reliability. During this period Prestolok has benefited from continuous improvement and is now one of the most advanced push-in fittings on the market. Prestolok uses "elastic teeth" grab ring technology invented and perfected by Parker, who guarantee its excellent tube retention qualities. Prestolok can be used not only with most types of plastic tubing available on the market (see Thermoplastic single tube and Pneumo-Tube bundles section P), but also with some metal tubing*, making it suitable for a wide range of applications D * See advantages section Technical features ody Nickel plated brass Threaded parts Nickel plated brass Sleeve rass aterial Grab ring Stainless steel Push button Polyacetal ack-up washer rass O-ring Nitrile Working pressure From 0.0 to 25 bar Working temperature From - 25 C to + 00 C pplications Prestolok has been designed to handle many industrial fluids compatible with its technical features. Thanks to its mechanical properties, Prestolok is a push-in fitting particularly suited to the most severe environments, such as welding, high temperatures, vibration. Welding Food industry Climate control utomotive Packaging achine tools D 4 Catalogue UK

84 Prestolok push-in fitting dvantages Compact ready-to-use fitting Wide product range covering all applications Full flow capability D rass nickel plated body rass is a raw material providing : - robustness, - excellent shock resistance, - good temperature capability, - excellent spark resistance. Nickel plating gives improved corrosion resistance and a bright appearance which does not deteriorate. Use with plastic or metal tubing Prestolok is a high performance pushin fittin Designed for use with most types of plastic tubing (polyamide, polyurethane, polyethylene, Pebax, Teflon...), this high performance fitting can also be used with copper tubing* conforming to DIN 786, NF5-20, S 287 Part 2 (tolerance mm). For steel, stainless steel tubing or other raw materials, please contact your Parker sales engineer. * Tube must be cut square and correctly deburred. Positive hold by a flexible stainless steel grab ring - the special shape of the radial teeth of the grab ring prevents longditudinal scratch marks on the tube. -the elasticity of the grab ring absorbs vibration and pulsating pressure. -a twist-free assembly, the tube can rotate freely even under pressure. Ready-to-use fitting The Prestolok range is manufactured with brass nickel plated male threads ready for use : - parallel threads are supplied with a preassembled, fully retained O-Ring seal, - taper threads are treated with a special PTFE for self sealing on assembly,reusable up to five times without additional sealing material. How to use Straight male connectors with internal hexagon - the internal hexagon allows vertical mounting with the use of an llen key. ecause the internal hexagon does not go completely through the fitting, the fittingcannot slip down the llen key during assembly. -the lack of external hexagon gives a significant reduction in the overall dimensions enabling close mounting of these fittings to give very compact installations. Plastic push button - simple manual pressure on the user-friendly push button allows instant disconnection of the tube. - tube sizes are marked on the push button for easy identification. ssembly - Cut the tube square (and correctly deburred for copper) - Insert the tube into the fitting until it bottoms. Disassembly - Simply press on the push button and withdraw the tube. D 5 Catalogue UK

85 Prestolok push-in fitting F23P - ale connector - SPT 0 P PTFE Threads are treated with PTFE sealing material Part number O P H. Weight Int. 4 /8 F23P4-/ /8 F23P6-/ /4 F23P6-/ /8 F23P8-/ /4 F23P8-/ This fitting has been designed for use where space is at a premium. It is assembled using the internal hexagon and an llen key. F28P - ale connector - metric straight thread D 0 J Part number J O H. Weight Int. 4 3x0.5 F28P x0.8 F28P x0.8 F28P This fitting has been designed for use where space is at a premium. It is assembled using the internal hexagon and an llen key. F3P - ale connector - SPT PTFE C4 P Threads are treated with PTFE sealing material Part number C4 P H. Weight Int. 4 /8 F3P4-/ /4 F3P4-/ /8 F3P5-/ /4 F3P5-/ /8 F3P6-/ /4 F3P6-/ /8 F3P8-/ /4 F3P8-/ /8 F3P8-3/ /4 F3P0-/ /8 F3P0-3/ /2 F3P0-/ /4 F3P2-/ /8 F3P2-3/ /2 F3P2-/ /8 F3P4-3/ /2 F3P4-/ FP - ale connector - NPTF Part number C4 P H. Weight Int. P C4 PTFE 6 /8-27 FP6-/ /4-8 FP6-/ /4-8 FP0-/ /8-8 FP0-3/ /8-8 FP2-3/ Threads are treated with PTFE sealing material For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 6 Catalogue UK

86 Prestolok push-in fitting F4P - ale connector - SPP C 4 J * No protective cap facility. Part number C4 J H Weight Int. 4 /8 F4P4-/ /4 F4P4-/ /8 F4P6-/8* /4 F4P6-/ /8 F4P8-/8* /4 F4P8-/ /8 F4P8-3/ /4 F4P0-/ /8 F4P0-3/ /2 F4P0-/ /4 F4P2-/ /8 F4P2-3/8* /2 F4P2-/ /8 F4P4-3/ /2 F4P4-/ D F8P - ale connector - metric straight thread Part number C4 J H. Weight Int. 4 5x0.8 F8P x F8P x0.8 F8P x F8P x.5 F8P C 4 J 8 2x.5 F8P x.5 F8P x.5 F8P ll straight male connectors have an internal hexagon (Int.H.) for use with an llen key to allow the fitting to be mounted in any position. This also permits close porting not possible when a spanner is used. D 7 Catalogue UK

87 Prestolok push-in fitting G4P - Female connector - SPP C 4 J Part number C4 J Weight 4 /8 G4P4-/ /8 G4P6-/ /4 G4P6-/ /8 G4P8-/ /4 G4P8-/ HP - Equal union D Part number Circlips* O Weight O 4 HP4 CIR HP5 CIR HP6 CIR HP8 CIR HP0 CIR HP2 CIR HP4 CIR * Unions can be used as bulkhead unions. Simply mount two circlips in the machined grooves provided. Three grooves are provided to allow for a range of wall thickness :.5, 2 and 5 mm. (For circlips part number, see chart above). WG4P - ulkhead union - female SPP C 2 J 2 W C Part number 2 C C2 J W Weight 4 /8 WG4P4-/8 x /8 WG4P6-/8 3x /4 WG4P6-/4 3x /8 WG4P8-/8 5x /4 WG4P8-/4 5x /8 WG4P0-3/8 8x /8 WG4P2-3/8 23x /2 WG4P2-/2 23x WP - ixed bulkhead equal union 2 W C C 4 C 2 2 Part number C C2 C4 W Weight ax x WP x WP x WP x WP x WP x WP This bulkhead fitting combines a Prestolok and etrulok connection, to connect a copper tube with a plastic tube. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 8 Catalogue UK

88 Prestolok push-in fitting WP - ulkhead equal union W C 4 C 4 C3P - Compact elbow - SPT Part number C4 W Weight ax. 4 x0.75 WP x WP x.25 WP x WP x.5 WP x.5 WP D C N P PTFE Threads are treated with PTFE sealing material Part number C N P Weight 4 /8 C3P4-/ /8 C3P6-/ /4 C3P6-/ /8 C3P8-/ /4 C3P8-/ /4 C3P0-/ /8 C3P0-3/ /8 C3P2-3/ /2 C3P2-/ /8 C3P4-3/ /2 C3P4-/ C6P - djustable male elbow - NPT Part number C C4 N P Weight C C4 P N 6 /4-8 C6P6-/ /8-8 C6P6-3/ /4-8 C6P0-/ /8-8 C6P0-3/ /8-8 C6P2-3/ /2-8 C6P2-/ C63P - djustable extended male elbow - SPT C N C4 P PTFE Threads are treated with PTFE sealing material Part number C C4 N P Weight 4 /8 C63P4-/ /4 C63P4-/ /8 C63P6-/ /4 C63P6-/ /8 C63P8-/ /4 C63P8-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 9 Catalogue UK

89 Prestolok push-in fitting C63P - djustable male elbow - SPT Part number C C4 N P Weight 4 /8 C63P4-/ /4 C63P4-/ /8 C63P6-/ /4 C63P6-/ /8 C63P8-/ C N C4 P PTFE Threads are treated with PTFE sealing material 8 /4 C63P8-/ /8 C63P8-3/ /4 C63P0-/ /8 C63P0-3/ /4 C63P2-/ /8 C63P2-3/ /2 C63P2-/ /8 C63P4-3/ /2 C63P4-/ D C64P - djustable male elbow - SPP Part number C C4 J N Weight 4 /8 C64P4-/ /4 C64P4-/ /8 C64P6-/ /4 C64P6-/ /8 C64P8-/ C C 4 J N 8 /4 C64P8-/ /8 C64P8-3/ /4 C64P0-/ /8 C64P0-3/ /4 C64P2-/ /8 C64P2-3/ /8 C64P4-3/ /2 C64P4-/ C64SP - Compact adjustable male elbow - SPP Part number C C4 J N Weight 4 /8 C64SP4-/ /8 C64SP6-/ /4 C64SP6-/ /8 C64SP8-/ /4 C64SP8-/ C C4 J N 8 3/8 C64SP8-3/ /4 C64SP0-/ /8 C64SP0-3/ /4 C64SP2-/ /8 C64SP2-3/ /2 C64SP2-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 0 Catalogue UK

90 Prestolok push-in fitting C68P - djustable male elbow - metric straight thread C N Part number C C4 J N Weight 4 3x0.5 C68P x0.8 C68P x0.8 C68P C 4 J C68SP - Compact adjustable male elbow - metric straight thread D Part number C C4 J N Weight 4 5x0.8 C68SP x0.8 C68SP C C4 J N EP - Equal union elbow Part number C Weight C 4 EP EP EP EP EP EP EP WE6P - 90 adjustable bulkhead union elbow Part number C C4 O W Weight ax. C W 4 x0.75 WE6P x WE6P x.25 WE6P x WE6P x.5 WE6P C 4 O For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D Catalogue UK

91 Prestolok push-in fitting JP - Equal union tee Part number C Weight C 4 JP JP JP JP JP JP JP D R63P - djustable male run tee - SPT Part number C C4 N P Weight N P PTFE 4 /8 R63P4-/ /4 R63P4-/ /8 R63P6-/ /4 R63P6-/ /8 R63P8-/ C4 C Threads are treated with PTFE sealing material 8 /4 R63P8-/ /8 R63P8-3/ /4 R63P0-/ /8 R63P0-3/ /4 R63P2-/ /8 R63P2-3/ /2 R63P2-/ /8 R63P4-3/ /2 R63P4-/ R64P - djustable male run tee - SPP Part number C C4 J N Weight N J 4 /8 R64P4-/ /4 R64P4-/ /8 R64P6-/ /4 R64P6-/ /8 R64P8-/ C C 4 8 /4 R64P8-/ /8 R64P8-3/ /4 R64P0-/ /8 R64P0-3/ /4 R64P2-/ /8 R64P2-3/ /8 R64P4-3/ /2 R64P4-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 2 Catalogue UK

92 Prestolok push-in fitting R68P - djustable male run tee - metric straight thread N J Part number C C4 J N Weight C C 4 4 3x0.5 R68P x0.8 R68P x0.8 R68P S63P - djustable male branch tee - SPT D C N C4 P PTFE Threads are treated with PTFE sealing material Part number C C4 N P Weight 4 /8 S63P4-/ /4 S63P4-/ /8 S63P6-/ /4 S63P6-/ /8 S63P8-/ /4 S63P8-/ /8 S63P8-3/ /4 S63P0-/ /8 S63P0-3/ /4 S63P2-/ /8 S63P2-3/ /2 S63P2-/ /8 S63P4-3/ /2 S63P4-/ S64P - djustable male branch tee - SPP Part number C C4 J N Weight N C J C 4 4 /8 S64P4-/ /4 S64P4-/ /8 S64P6-/ /4 S64P6-/ /8 S64P8-/ /4 S64P8-/ /8 S64P8-3/ /4 S64P0-/ /8 S64P0-3/ /4 S64P2-/ /8 S64P2-3/ /8 S64P4-3/ /2 S64P4-/ S68P - djustable male branch tee - metric straight thread Part number C C4 J N Weight N C 4 3x0.5 S68P x0.8 S68P x0.8 S68P J C 4 D 3 Catalogue UK

93 Prestolok push-in fitting anjo or double banjo fittings with banjo or stacking banjo bolts permit space-saving connections and can be used where the mounting of elbows is not possible. D CORP - Single banjo body only Y X Part number Part No. Part No. X Y Weight single bolt stacking bolt 4 CORP4-5 SC8U5-4 SC8UD CORP4-0 SC4U/8-4 SC4UD/ CORP6-0 SC4U/8-4 SC4UD/ CORP6-3 SC4U/4-6 SC4UD/ CORP8-0 SC4U/8-4 SC4UD/ CORP8-3 SC4U/4-6 SC4UD/ CORP0-7 SC4U3/8-0 SC4UD3/ CORPD - Double banjo body only X Y Part number Part No. Part No. X Y Weight single bolt stacking bolt 4 CORP4D5 SC8U5-4 SC8UD CORP4D0 SC4U/8-4 SC4UD/ CORP6D0 SC4U/8-4 SC4UD/ CORP6D3 SC4U/4-6 SC4UD/ CORP8D0 SC4U/8-4 SC4UD/ COR8P/COR4P - Single banjo - assembled C Part number C D J K N O Y Weight Y N K O J 4 5x0.8 COR8P /8 COR4P4-/ /8 COR4P6-/ /4 COR4P6-/ /8 COR4P8-/ D 8 /4 COR4P8-/ /8 COR4P0-3/ These parts are delivered complete with sealing washer. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 4 Catalogue UK

94 COR8PD/COR4PD - Double banjo - assembled Prestolok push-in fitting Y C N K O J Part number C D J K N O Y Weight 4 5x0.8 COR8P4D /8 COR4P4D/ x COR8P x.5 COR8P /8 COR4P6D/ D 6 /8 COR4P6D/ /8 COR4P8D/ These parts are delivered complete with sealing washer. D SC8U/SC4U - Single banjo bolt with seals C Part number C D J K Weight K J 5x0.8 SC8U /8 SC4U/ /4 SC4U/ /8 SC4U3/ D SC8UD/SC4UD - Stacking banjo bolt with seals C Part number C D J K Weight 5x0.8 SC8UD /8 SC4UD/ /4 SC4UD/ K J D For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 5 Catalogue UK

95 Prestolok push-in fitting FNP - Plug TEP - Tube end expander Part number Weight 4 FNP FNP FNP FNP FNP FNP D 2 Part number Weight 4 6 TEP TRP - Tube end reducer 2 Part number Weight TRP TRP TRP TRP TRP TRP TRP TRP TRP TRP TRP TRP T23HFP - Tube end male adaptor - SPT C PTFE Part number C N P Weight 5 /8 T23HFP5-/ /4 T23HFP5-/ N P Threads are treated with PTFE sealing material For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. D 6 Catalogue UK

96 Prestoweld 2 Spark resistant push-in fittings Catalogue UK

97 Prestoweld 2 push-in fitting Index Straight connectors & bulkhead unions ale connector ale connector SPP metric Equal union Equal bulkhead union F4PW - p. E 4 F8PW - p. E4 HPW - p. E4 WPW - p. E 5 90 elbows & tees E Equal union tee ale elbow - SPP Equal elbow union JPW - p. E 5 C64PW - p. E 5 EPW - p. E 6 daptors/ accessories Plug Tube end expander FNP - p. E 6 TRPW - p. E 6 Technical tubing Please consult Thermoplastic single tubes and Pneumo-Tube bundles section (P). E 2 Catalogue UK

98 Prestoweld 2 push-in fitting Principle Prestoweld 2 push-in welding fittings have been specifically designed to meet the stringent requirements of the robotic welding industry for pneumatic controls. Developed from the Prestolok push-in fitting, Prestoweld 2 uses elastic teeth grab ring technology which guarantees excellent tube retention particularly critical in these applications. Prestoweld 2 is designed for use with weld spark resistant polyurethane halogene free Parker Prestoweld 2 tubin It features a special polyamide Starflam U2Z22/8 push-button design which resist to sparks and weld spatter and prevents tube damagin Prestoweld 2 fittings are perfectly designed for use with pneumatic systems in the robotics industry. E Technical features aterial Working Working ody Threaded Sleeve Grab Push ack-up O-ring pressure temperature parts ring button washer Nickel Nickel rass Stainless Polyamide rass Nitrile From 0.0 From -25 C plated plated steel STRF to to brass brass U2Z22/8 25 bar +00 C dvantages Full flow capabilities Spark resistant Compact installation Wide range rass nickel plated body rass is a raw material providing: - robustness, - excellent shock resistance, - good temperature capability, - excellent spark resistance. Nickel plating gives improved corrosion resistance and a bright appearance which does not deteriorate. Protective push-button - the unique design of the Prestoweld 2 polyamide Starflam U2Z22/8 pushbutton and its thermic properties prevent damages from sparks and weld spatter. - simple manual pressure on the push button allows instant disconnection of the tube. - the tube size are marked on the push button for easy identification. Ready-to-use fitting The Prestoweld 2 range contains ready to use fittings equiped by SPP adaptors with unloosable o-rin - this fitting do not need tubing preparation. - the Prestoweld 2 tubing allow a low bend radius for a best space savin E 3 Catalogue UK

99 Prestoweld 2 push-in fitting F4PW - ale connector - SPP Part number C4 J H Weight Int. C 4 J 4 /8 F4PW4-/ /4 F4PW4-/ /8 F4PW6-/ /4 F4PW6-/ /8 F4PW8-/ /4 F4PW8-/ /8 F4PW8-3/ /4 F4PW0-/ /8 F4PW0-3/ /2 F4PW0-/ /4 F4PW2-/ /8 F4PW2-3/ /2 F4PW2-/ /8 F4PW4-3/ /2 F4PW4-/ E F8PW - ale connector - etric Part number C4 J H Weight Int. 4 5x0.8 F8PW C 4 J HPW - Equal union Part number 0 Weight O 4 HPW HPW HPW HPW HPW HPW For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. E 4 Catalogue UK

100 Prestoweld 2 push-in fitting WPW - Equal bulkhead union W Part number C4 J 0 W Weight max 6 3x WPW x.25 WPW x WPW x.5 WPW C 4 C 4 JPW - Equal union tee E C Part number C Weight 6 JPW JPW JPW JPW C64PW - djustable male elbow SPP Part number C C4 J N Weight C N 6 /8 C64PW6-/ /4 C64PW6-/ /8 C64PW8-/ /4 C64PW8-/ /8 C64PW8-3/ C 4 J 0 /4 C64PW0-/ /8 C64PW0-3/ /4 C64PW2-/ /8 C64PW2-3/ For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. E 5 Catalogue UK

101 Prestoweld 2 push-in fitting EPW - Equal union elbow Part number C Weight C 4 EPW EPW EPW EPW EPW EPW FNP - Plug E Part number Weight 6 FNP FNP FNP FNP TRPW - Tube end expander 2 2 Part number O Weight 8 4 TRPW TRPW TRPW TRPW TRPW TRPW TRPW Parker Prestoweld 2 fittings are designed to be used with the Parker Prestoweld 2 Tube. See «Thermoplastic single tube and Pneumo-Tube bundles» section (P). For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. E 6 Catalogue UK

102 Pneumatic integrated function fittings Catalogue UK

103 Pneumatic integrated function fittings Index Prestoflow anjo flow regulator - compact with push-in connection metric bolt PTF8P / PTF8P - p. F 9 with push-in connection SPP bolt PTF4P / PTF4P - p. F 9 with threaded connection SPP bolt PTF4 - p. F 9 with spark resistant push-in connection - SPP bolt PTF4PW - p. F 0 Prestoflow anjo flow regulator - swivel outlet with push-in connection metric bolt PTF8E6P - p. F with push-in connection SPP bolt PTF4E6P - p. F Prestoflow anjo flow regulator - with locknut F with push-in connection metric bolt PTF8P - p. F 2 with push-in connection metric bolt PTF8P - p. F 3 with push-in connection SPP bolt PTF4P - p. F 3 with threaded connection/ metric bolt PTF8 / PTF8 - p. F 3 with threaded connection - SPP bolt PTF4 - p. F 3 with compression connection SPP bolt PTF4CO - p. F 3 Prestoflow Flow regulator - In-line with push-in connection PTFIPK - p. F 5 with push-in connection ultrafine adjustment PTFIPK - p. F 5 with push-in connection PTFIWPK - p. F 5 Prestoflow compact and micro NEW NEW NEW NEW with push-in connection SPP / metric bolt PTFC4/8PK - p. F 6 with push-in connection SPP / metric bolt PTFC4/8PK - p. F 6 with push-in connection SPP bolt PTFC4PK - p. F 6 with push-in connection SPP bolt PTFC4PK - p. F 7 NEW NEW with push-in connection metric bolt PTF8PK - p. F 7 with push-in connection metric bolt PTF8PK - p. F 7 F 2 Catalogue UK

104 Index Prestobloc and Prestoload lockers Pneumatic integrated function fittings Unloaders with push-in connection SPP bolt PW- - p. F 9 with threaded connection SPP bolt PW- - p. F 9 with push-in connection SPP bolt PWE- - p. F 2 with threaded connection SPP bolt PWE- - p. F 2 Prestotwin flow regulator + blocker flow regulator + unloader with push-in connection SPP bolt / barrel adjustment PWR-H - p. F 23 with push-in connection SPP bolt / barrel adjustment PWR-HE - p. F 23 F Prestosensor Pressure sensors pneumatic output electrical output electronic output with push-in connection SPP and metric bolt PTP4/8P - p. F 24 with threaded connection SPP and metric bolt PTP4/8 - p. F 25 plug-in sensor electrical output PWS- - p. F 25 plug-in sensor electronical output PWS-E - p. F 25 banjo socket with sensor locking clip PWS- - p. F 25 Prestostart Pneumatic slow start fittings power valve version system isolating version with push-in connection SPP bolt PCV4PK - p. F 27 with threaded connection SPP bolt PCV4 - p. F 27 with push-in connection SPP bolt PIV4PK- p. F 27 with threaded connection SPP bolt PIV4 - p. F 27 Prestoreduce Pressure reducers banjo version in-line version with push-in connection SPP bolt PR4P - p. F 29 with threaded connection SPP bolt PR4 - p. F 29 with push-in connection SPP bolt PRIP - p. F 29 with threaded connection SPP bolt PRI4 - p. F 29 Prestosil Flow regulator + silencer NEW bar 0 8 and ccessories with threaded connection - SPP PRS - p. F 30 non-return equal union PW- - p. F 3 in-line Prestoflow assembly clip Clip - p. F 3 manual ratchet control for pressure reducers Ratchet - p. F 3 sealing plug for pressure reducers Splug - p. F 3 pressure gauge for push-in fitting P Gauge - p. F 3 F 3 Catalogue UK

105 Pneumatic integrated function fittings Product family Symbol Function Part number Prestoflow - Flow regulator PTF PTFIPK exhaust flow control inlet flow control in-line flow control Prestoflow flow control regulators are designed to adjust the speed of the cylinder piston rod by controlling the flow of air. They are unidirectional and are normally installed on the exhaust port of the cylinder. For specific applications, they could be mounted in-line or on the inlet port. Compact and micro series are specially designed where space saving is a priority. PTF... p. F 9 PTFE6... p. F PTF... p. F 2 PTFI... p. F 5 PTFC... p. F 6 PTFC... p. F 6 PTF... p. F 7 PTFE6P PTFP Prestobloc - locker F PW- Prestobloc is a pneumatically controlled check valve for mounting onto the cylinder port. It is designed to block the movement of the piston rod at selected positions. s a safety device it prevents the exhausting of air from the cylinder in the event of a power failure. PW-... p. F 9 Prestoload - Unloader PWE- Prestoload is a pneumatically controlled exhaust valve for direct mounting onto the cylinder ports. It allows the rapid exhaust of air from the cylinder returning the piston rod to the initial position. PWE-... p. F 2 Prestotwin Flow regulator + blocker Flow regulator + unloader PWR-H block + control Prestotwin fittings combine flow control with blocking function or unloading function. This concept allows a more compact installation and saves assembly time. PWR-H... p. F 23 PWR-HE... p. F 23 PWR-HE unload + control F 4 Catalogue UK

106 Pneumatic integrated function fittings Product family Symbol Function Part number Prestosensor Pressure sensor PTP8P PTP8 PWS- PWS- Prestosensor sensor fittings are designed to detect pressure drop and can be mounted on a cylinder or control valve. The sensor fittings produce a signal, either, pneumatic, electric or electronic when the back pressure disappears at the end of stroke. PTP4/8... p. F 24 PWS-02.. p. F 25 + PWS-... p. F 25 PWS-E... p. F 25 + PWS-... p. F 25 PWS-E0... p. F 25 + PWS-... p. F 25 Prestostart Slow start fitting F PCV4PK PCV4 for isolating valve Prestostart slow start fittings allow the air pressure to increase gradually when the pneumatic installation is started. This slow start prevents shocks that may occur when full system pressure is introduced, thus reducing the risk of damage to components. PCV... p. F 27 PIV... p. F 27 for control valve Prestoreduce Pressure reducer Prestoreduce pressure reducing fittings allow for the manual reduction of air pressure in a pneumatic installation. This pressure reduction limits the amount of compressed air used, resulting in a saving of energy. PR... p. F 29 PRI... p. F 29 PR4P PRIP Prestosil Flow regulator + silencer Prestosil combined silencers and flow control regulators provide efficient silencing of exhaust noise and permits precise adjustment of piston rod speed. PRS... p. F 30 PRS F 5 Catalogue UK

107 Pneumatic integrated function fittings Prestoflow - Flow regulators Parker offer a wide range of flow regulators to meet a large variety of applications. Prestoflow can be fitted directly to a cylinder port or mounted in the line. Prestoflow regulators with push-in terminations are suitable for use with a wide range of plastic tubin Prestoflow regulators with threaded terminations can be adapted for use with copper and steel tubing or hoses. PTFE6P PTF PTFIPK PTFP F General principle The piston rod moves as a result of the pressure differential either side of the piston. The speed of the rod is normally determined by the exhaust air flow from the cylinder. The control of this air flow is via an adjustable needle valve installed on the exhaust port. On single acting cylinders and some miniature (5) double acting cylinders, the air flow can be controlled from the inlet port. To permit regular and smooth movement of the piston rod, flow control should be made as near to the cylinder as possible. Inlet Inlet chamber Outlet chamber Exhaust Flow regulation on the exhaust port Inlet Outlet chamber chamber Inlet Exhaust Flow regulation on the inlet port Operation The mounting of two flow control devices on a cylinder permits speed control of the cylinder rod in both directions. The sketch opposite shows a cylinder with inlet air at port. ir passes freely through the flow control valve, with the check valve in the open position. The exhaust is controlled by the flow control fitting, where the check valve in the closed position forces the air to go through the adjustable needle valve. The function of and are reversed when inlet air is applied to port. Flow control on a double acting cylinder F 6 Catalogue UK

108 Pneumatic integrated function fittings Flow characteristics Prestoflow pneumatic integrated fittings are designed to permit maximum flow in both directions. This full flow in both directions, together with the very precise setting of the screw, permits a wide range of adjustment between the minimum and maximum speeds. The sketch opposite shows the flow progression according to the adjustment of the screw. Flow Inlet Outlet 20% 40% 60% 80% 00% djustment turns F Selection guide Feature PTF series PTF series PTFE6 series PTFI series ounting Direct Yes Yes Yes - Inline Yes Control Outlet Yes Yes Yes Yes Inlet Yes Yes - - Tube connection Push-in 4 mm - 2 mm 4 mm - 2 mm 4 mm - 8 mm 4 mm - 2 mm compression - 6 mm - 8 mm - - Threaded-Female /8 - /2 SPP /8 - /2 SPP - - olt terminations /8 - /2 SPP /8 - /2 SPP /8-3/8 SPP - Working pressure ar Working temperature C -25 C C -25 C C -25 C C -5 C C ody material rass rass rass High resistance polyamide djustment screw material rass rass rass rass-duralumin (Ultrafine adjust) ocknut No Yes No Yes Panel mounting Yes ank mounting Yes Swivel Outlet - - Yes - Flow regulators - assembly torques To ensure a leak free connection for port mounted regulators the regulator bolt should be tightened in accordance with the table opposite. ssembly torque Thread in. Nm ax. Nm /8 6 9 / / / F 7 Catalogue UK

109 Pneumatic integrated function fittings Prestoflow - Flow regulator - Compact series Principle Prestoflow compact flow regulators are designed for mounting directly onto cylinder ports to provide precise control of piston rod speed. Thanks to their compactness they are particularly suitable for applications where space is at a premium. These unidirectional flow regulators are available for exhaust or inlet flow control. - check valve blocks the full flow ports in the exhaust or inlet direction. Exhaust flow control Inlet flow control - The flow is controlled by a needle valve fitted in the regulator bolt. djustment screw Check valve To power valve F Cylinder Technical features ody material olt material olt thread Sealing device Terminations Working temperature Working pressure rass black epoxy coated rass 5 /8 SPP /4 SPP 3/8 SPP /2 SPP 5 Nylon washer /8 - /2 SPP Nitrile E. D. seal 4 mm - 2 mm push-in connection /8 - /2 SPP + 5 Female thread DIN 3852 long From - 25 C to + 00 C From to 0 bar Flow adjustment Flow control is adjusted with an llen key. The large number of turns from fully closed to fully open allows for precise flow control. F 8 Catalogue UK

110 Pneumatic integrated function fittings PTF4/8P - Flow regulator with push-in connection Part number C5 D G H J N N O Y Weight H C5 4 5x0.8 PTF8P45* /8 PTF4P4-/ x0.8 PTF8P65* /8 PTF4P6-/ /4 PTF4P6-/ O 6 3/8 PTF4P6-3/ /8 PTF4P8-/ /4 PTF4P8-/ /8 PTF4P8-3/ /4 PTF4P0-/ Exhaust flow control 0 3/8 PTF4P0-3/ /2 PTF4P0-/ /8 PTF4P2-3/ /2 PTF4P2-/ F * These fittings are supplied with Nylon seal. PTF4/8P - Flow regulator with push-in connection Y Y D N J N G H Part number C5 D G H J N N O Y Weight O C5 N J N 4 5x0.8 PTF8P45* /8 PTF4P4-/ x0.8 PTF8P65* /8 PTF4P6-/ /4 PTF4P6-/ D G 8 /8 PTF4P8-/ /4 PTF4P8-/ Inlet flow control * These fittings are supplied with Nylon seal. PTF4 - Flow regulator with threaded connection U H Part number C5 D G H J U N N O Y Weight O Y C5 N J N /8 /8 PTF4-/ /4 /4 PTF4-/ /8 3/8 PTF4-3/ /2 /2 PTF4-/ D G Exhaust flow control Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 9 Catalogue UK

111 Y Pneumatic integrated function fittings PTF4PW - Flow regulator with spark resistant push-in connection O NEW D H C5 N J N Part number C5 D G H J N N O Y Weight 6 /8 PTF4PW6-/ /4 PTF4PW6-/ /8 PTF4PW8-/ /4 PTF4PW8-/ /8 PTF4PW8-3/ /4 PTF4PW0-/ /8 PTF4PW0-3/ /8 PTF4PW2-3/ /2 PTF4PW2-/ G F For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 0 Catalogue UK

112 Prestoflow - Flow regulator - Swivel outlet Pneumatic integrated function fittings Principle Prestoflow unidirection swivel flow regulators are designed for mounting directly onto the cylinder exhaust port and provide precise control of the piston rod speed. The swivel outlet is designed to allow vertical or oblique tube exit where access is restricted. To power valve - check valve blocks the full flow ports in the exhaust direction The flow is controlled by a needle valve fitted in the regulator bolt. - The swivel outlet can be positioned in the most suitable direction. Fine thread adjustment screw Check valve F Cylinder Technical features olt material Swivel elbow material olt material olt threads Sealing device Terminations djustment screw Working temperature Working pressure rass black epoxy coated High resistance polyamide rass 5 /8 SPP /4 SPP 3/8 SPP Nylon washer /8-3/8 SPP Nitrile E. D. seal 4-8 mm push-in rass From - 25 C to + 70 C From to 0 bar Flow adjustment Flow control is adjusted with an llen key. The large number of turns from fully closed to fully open allows for precise flow control. PTF4/8E6P - Flow regulator with push-in connection P Y 2 D G H C5 N J N Part number C5 D G H J 2 N N P Y Weight 4 5x0.8 PTF8E6P45* /8 PTF4E6P4-/ x0.8 PTF8E6P65* /8 PTF4E6P6-/ /4 PTF4E6P6-/ /8 PTF4E6P6-3/ /8 PTF4E6P8-/ /4 PTF4E6P8-/ /8 PTF4E6P8-3/ * These fittings are supplied with Nylon seal. Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). F Catalogue UK

113 Pneumatic integrated function fittings Prestoflow - Flow regulator - ocknut series Principle Exhaust flow control Prestoflow locknut series flow regulators are designed for mounting directly onto the cylinder ports to provide precise control of piston rod speed. When the desired flow has been set the adjusting bolt can be locked in position. These unidirectional flow regulators are available for exhaust or inlet flow control. Inlet flow control - check valve blocks the full flow ports in the exhaust or inlet direction. djustment screw - The flow is controlled by a needle valve fitted in the regulator bolt. - The adjustment screw can be locked in position to prevent tamperin 360 Check valve Cylinder To power valve F Technical features ody material olt material ocknut olt thread Sealing device Terminations Working temperature Working pressure rass black epoxy coated rass rass 5 /8 SPP /4 SPP 3/8 SPP /2 SPP 5 thread Nylon washer /8 - /2 SPP Nitrile E. D. seal 4 mm - 2 mm push-in connection 6mm - 2 mm compression connection /8 - /2 SPP + 5 Female threads DIN 3852 long From - 25 C to + 00 C From to 0 bar Flow adjustment Flow control is adjusted with an llen key. When the desired flow is set the adjusting screw can be locked using the locking nut. The large number of turns from fully closed to fully open allows for precise flow control. PTF8P - Flow regulator with push-in connection O Y D G H H2 C5 N J Inlet flow control N Part number C5 D G H H2 J N N O Y Weight 4 5x0.8 PTF8P Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). F 2 Catalogue UK

114 Pneumatic integrated function fittings PTF4/8P - Flow regulator with push-in connection H Part number C5 D G H H2 J N N O Y Weight O H2 U C5 N Y J D G Exhaust flow control N 4 5x0.8 PTF8P45* /8 PTF4P4-/ x0.8 PTF8P65* /8 PTF4P6-/ /4 PTF4P6-/ /8 PTF4P6-3/ /8 PTF4P8-/ /4 PTF4P8-/ /8 PTF4P8-3/ /4 PTF4P0-/ /8 PTF4P0-3/ /2 PTF4P0-/ /8 PTF4P2-3/ /2 PTF4P2-/ * These fittings are supplied with Nylon seal. F PTF4/8 - Flow regulator with threaded connection H H2 U C5 N O N Y J D G Exhaust flow control Part number C5 D G H H2 J U N N O Y Weight 5x0.8 5x0.8 PTF85* /8 /8 PTF4-/ /4 /4 PTF4-/ /8 3/8 PTF4-3/ /2 /2 PTF4-/ * These fittings are supplied with Nylon seal. PTF8 - Flow regulator with threaded connection O Y U D G H H2 C5 N J Inlet flow control N Part number C5 D G H H2 J U N N O Y Weight 5x0.8 5x0.8 PTF PTF4CO - Flow regulator with compression connection N H2 C5 N J D G Y Part number C5 D G H2 J N N Y Weight 6 0x /8 PTF4CO6-/ x /8 PTF4CO8-/ x.5 /4 PTF4CO0-/ x.5 3/8 PTF4CO4-3/ x.5 /2 PTF4CO8-/ * These fittings can be assembled with Push-ok fittings 3F82 series (see page O27). F 3 Catalogue UK

115 Pneumatic integrated function fittings Prestoflow - Flow regulator - In-line series Principle Prestoflow unidirection in-line flow regulators are designed to be used directly in the compressed air line when cylinder access is difficult or where another function fitting is already connected to the cylinder port. The fine thread knurled adjuster provides precise control of piston rod speed. When the desired flow has been set the adjusting bolt can be locked in position. - check valve blocks the full flow ports in the exhaust direction. - The flow is controlled by a needle valve fitted in the regulator body. Clip - These regulators can be : - mounted using the 4 fixing holes - assembled into banks using the joining clips included. Slots djustment screw ocknut F Check valve Exhaust from cylinder To power valve Technical features ody material Cartridge material djustment and locking nut Standard adjustment Ultrafine adjustment Terminations Working temperature Working pressure High resistance polyamide rass rass Duralumin 4 mm - 2 mm push-in From - 5 C to + 70 C From to 0 bar Flow adjustment Flow control is adjusted with a screwdriver or manually with the knurled nut. When the desired flow is set the adjusting screw can be locked using the locking nut. The large number of turns from fully closed to fully open allows for precise flow control. F 4 Catalogue UK

116 Pneumatic integrated function fittings PTFIPK - Flow regulator with push-in connection H2 H N2 Part number H H2 K N N2 T Weight in. ax. dia. 4 PTFIPK PTFIPK PTFIPK PTFIPK PTFIPK Ø T N K PTFIPK - Flow regulator with push-in connection - Ultrafine adjustment F H Part number H K N N2 T Weight in. ax. dia. 4 PTFIPK PTFIPK N2 Ø T N K PTFIWPK - Flow regulator with push-in connection - Panel H2 H Part number C H H H2 H3 T W Weight in. ax. dia. ax. C H3 Ø T 4 PTFIWPK4* PTFIWPK6* PTFIWPK PTFIWPK PTFIWPK * Ultrafine adjustment W H Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 5 Catalogue UK

117 Pneumatic integrated function fittings PTFC4/8PK - compact exhaust flow control - SPP/metric NEW Part Number C5 G J N N O Weight C5 4 5 PTFC8PK /8 PTFC4PK4-/ PTFC8PK /8 PTFC4PK6-/ O N N 6 /4 PTFC4PK6-/ /8 PTFC4PK8-/ J 8 /4 PTFC4PK8-/ G 8 3/8 PTFC4PK8-3/ /4 PTFC4PK0-/ /8 PTFC4PK0-3/ F PTFC4/8PK - compact inlet flow control - SPP/metric NEW Part Number C5 G J N N O Weight 4 5 PTFC8PK /8 PTFC4PK4-/ O C5 N J N 6 5 PTFC8PK /8 PTFC4PK6-/ /4 PTFC4PK6-/ /8 PTFC4PK8-/ /4 PTFC4PK8-/ G 8 3/8 PTFC4PK8-3/ /4 PTC4PK0-/ /8 PTFC4PK0-3/ PTFC4PK - compact exhaust flow control - SPP NEW C5 Part Number C C5 G G J N N O Weight maxi mini 4 /8 PTFC4PK4-/ /8 PTFC4PK6-/ /4 PTFC4PK6-/ N O 8 /8 PTFC4PK8-/ /4 PTFC4PK8-/ N J G G C 8 3/8 PTFC4PK8-3/ /4 PTFC4PK0-/ /8 PTFC4PK0-3/ /2 PTFC4PK2-/ F 6 Catalogue UK

118 Pneumatic integrated function fittings PTFC4PK - compact inlet flow control - SPP NEW Part Number C C5 G G J N N O Weight maxi mini N N J G G C5 C O 4 /8 PTFC4PK4-/ /8 PTFC4PK6-/ /4 PTFC4PK6-/ /8 PTFC4PK8-/ /4 PTFC4PK8-/ /8 PTFC4PK8-3/ /4 PTFC4PK0-/ /8 PTFC4PK0-3/ /2 PTFC4PK2-/ F PTF8PK - micro exhaust flow control - metric NEW C5 Part Number C5 G G J N N O Weight maxi mini 4 5 PTF8PK PTF8PK N N J G G O PTF8PK - micro inlet flow control - metric NEW C5 Part Number C5 G G J N N O Weight maxi mini 4 5 PTF8PK PTF8PK N N J O G G F 7 Catalogue UK

119 Pneumatic integrated function fittings Prestobloc - Pilot-operated blocking fittings Principle Prestobloc pilot-operated blocking fittings are designed for mounting directly to the cylinder ports. vailable with push-in or threaded terminations, these function fittings permit safe and immediate stopping of the piston rod by blocking the cylinder supply and exhaust. Control signal - Pilot operated diaphragm maintains full flow when pilot signal is present. Diaphragm - Spring closes the poppet valve locking air in the cylinder when the pilot signal is removed. Poppet valve To power valve F Spring Cylinder - Prestobloc fittings used in conjuction with Prestoflow flow regulators are mounted on inlet and outlet ports. - Pilot signal should be independent from the control valve. Prestobloc fitting oving exhaust locked exhaust supply P Pilot signal P supply Removal initiates blocking locking principle Technical features ody material olt material olt thread Sealing device Terminations Pilot termination Working temperature Working pressure Zinc alloy epoxy coated rass /8 SPP /4 SPP 3/8 SPP /2 SPP Nylon washer 6mm to 2 mm push-in /4 to /2 SPP female thread 4 mm push-in From - 5 C to + 60 C From 0 to 0 bar Operating characteristics olt size /8" /4" 3/8" /2" Pilot operating pressure (00% flow) 2 bar 4 bar 6 bar 8 bar Pilot release pressure 2 bar 4 bar 6 bar 8 bar ax. input flow at 6 bar 500 l/mn NR 650 l/mn NR 300 l/mn NR 2300 l/mn NR F 8 Catalogue UK

120 Pneumatic integrated function fittings pplications Safety stop Prevents descent under load in the event of power failure Stroke control Stops the piston in various positions for conveying and handling applications. Safety locks Safety guards for assembly and punch presses. Combination with an emergency switch : restarting the cylinder after resetting the emergency switch. 2 P F PW- - locker with push-in connection 2 Part number C5 J N N O Y Weight N 2 O J N C5 Y 6 /8 4 PW /4 4 PW /4 4 PW /8 4 PW /8 4 PW /2 4 PW PW- - locker with threaded connection N 2 O J N C5 Y 2 Part number C5 J N N O Y Weight /8 /4 4 PW /4 /4 4 PW Push-in, Ø 4 mm 2 Part number C5 J N N O Y Weight 3/8 3/8 4 PW /2 /2 4 PW *vailable with Ø 4 mm push-in connection : add 4 to the end of the order code - example PW-8334 Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 9 Catalogue UK

121 Pneumatic integrated function fittings Prestoload - Pilot operated unloading fittings Principle Prestoload pilot operated unloading fittings are designed for mounting directly to the cylinder ports. vailable with push-in or threaded terminations these function fittings allow the rapid exhaust of the cylinder chamber when the pilot signal is removed. Operation - Under normal conditions the pilot pressure keeps the valve closed. Control signal Exhaust vent - When the pilot pressure is removed the pressure in the cylinder lifts the valve allow a rapid exhaust of air through the vent. Valve To power valve F Cylinder - ounted directly onto the cylinder port the Prestoload fitting enhances the cut off action of the main control valve of the pneumatic system. Pilot signal - Prestoload can be used in conjunction with flow regulators for piston speed adjustment. In this case the air exhaust speed is dependent upon the cross section of the restrictor. ain control valve Cylinder exhaust valve Speed control device Principle of exhaust air from a pneumatic cylinder Technical features ody material olt material olt thread Sealing device Terminations Pilot Termination Working temperature Working pressure Zinc alloy epoxy coated rass /8 SPP /4 SPP 3/8 SPP /2 SPP Nylon washer 6 mm - 2 mm push-in /4 - /2 SPP female thread 4 mm push-in From - 5 C to + 60 C From to 0 bar Operating characteristics olt size Pilot operating pressure 3 bar 6 bar 8 bar Pilot release pressure 3 bar 6 bar 8 bar ax output flow at 6 bar /8" /4" 3/8" /2" l/mn NR 2800 l/mn NR 3950 l/mn NR 4750 l/mn NR F 20 Catalogue UK

122 Pneumatic integrated function fittings PWE- - Unloader with push-in connection 2 O N C5 2 Part number C5 N N O Y Weight 6 /8 4 PWE /4 4 PWE /8 4 PWE /2 4 PWE N Y PWE- - Unloader with threaded connection 2 Part number C5 N N O Y Weight F 2 O N C5 /8 /4 4 PWE /4 /4 4 PWE /8 3/8 4 PWE /2 /2 4 PWE N Y Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). vailability of the items : please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 2 Catalogue UK

123 Pneumatic integrated function fittings Prestotwin - Combined flow - blocking - unloading valves Principle Prestotwin are multi-function fittings combining flow control and blocking or flow control and unloadin This avoids the requirement for two function fittings offering a compact solution with significant space savin They meet the requirements for a safety fitting and incorporate the facility to accurately control the piston rod speed. Operation PVF4PK Flow regulator + blocker - The pilot signal acting on the diaphragm keeps the poppet valve open. When the pilot signal is removed the spring closes the poppet valve. - Flow control is obtained by the adjustment of the rotating barrel directing air through the orifices of the flow control adjuster. - The flow control locknut ensures the optimum setting is maintained. Combined flow control and blocker Pilot Control Diaphragm Flow control adjuster Poppet valve Spring Cylinder Speed control and blocker To power valve Flow control locknut Speed control and unloader F PSPF4PK Flow regulator + unloader - The pilot signal operating on the poppet valve keeps it closed. When the pilot signal is removed the cylinder air exhausts through the vent. - Flow control is obtained by the adjustment of the rotating barrel directing air through the orifices of the flow control adjuster. - The flow control locknut ensures the optimum setting is maintained. Combined flow control and unloader Pilot Control Poppet valve Flow control adjuster Cylinder Flow control locknut To power valve Technical features ody material olt material olt thread Sealing device Termination Pilot termination Flow control adjustment Flow control locking Working temperature Working pressure PVF4PK PSPF4PK Zinc alloy epoxy coated rass /8SPP /4SPP 3/8SPP Nylon washer 4mm - 8mm push-in 4mm push-in rotating barrel knurled locknut From -5 C to + 60 C From to 0 bar From 0 to 0 bar F 22 Catalogue UK

124 Pneumatic integrated function fittings PWR-H - Flow regulator + locker with push-in connection N 2 O C5 Y N J 2 Part number C5 J N N O Y Weight 4 /8 4 PWR-H /8 4 PWR-H /4 4 PWR-H /4 4 PWR-H /8 4 PWR-H /8 4 PWR-H Operating characteristics Part number Pilot operating pressure Pilot release pressure 2 bar 4 bar 6 bar 8 bar 2 bar 4 bar 6 bar 8 bar PWR-H PWR-H PWR-H PWR-H PWR-H PWR-H F PWR-HE - Flow regulator + Unloader with push-in connection 2 Part number C5 J N N O Y Weight 4 /8 4 PWR-HE /8 4 PWR-HE /4 4 PWR-HE /4 4 PWR-HE /8 4 PWR-HE /8 4 PWR-HE Operating characteristics Part number Pilot operating pressure Pilot release pressure 3 bar 6 bar 8 bar 3 bar 6 bar 8 bar PWR-HE PWR-HE PWR-HE PWR-HE PWR-HE PWR-HE Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 23 Catalogue UK

125 Pneumatic integrated function fittings Prestosensor - Pressure sensor fittings Principle Prestosensor fittings are designed for direct mounting onto the cylinder. These sensors detect end of stroke travel by the variation in internal operating pressure. The sensing can be pneumatic, electric or electronic to suit the application. These fittings remove the need for mechanical position switches. Operation - ounting to cylinder port - Pressure sensors should be mounted in conjunction with flow regulators - Pressure sensing on diaphragm valve. Pi S P Po To power valve Pneumatic back pressure sensor Supply pressure P pressure valve reversal exhaust counter-pressure Pi pressure valve reversal Po start of cylinder travel back pressure sensor switching threshold Time end of cylinder travel F i P Pi Po o Flow control regulator Pneumatic back pressure sensor i i Pi i o Po o Po o Rest position -i emits a signal -o emits no signal id stroke -i emits no signal -o emits no signal Pi Po Cylinder Pi End of stroke -i emits no signal -o emits a signal ounting of pressure sensors Signals from pressure sensors Technical features Pneumatic output version Zinc alloy and thermoplastic ody material Electric and electronic version Thermoplastic olt material 5: bichromate steel /8 to /2 SPP: brass olt threads 5 /8 SPP /4 SPP 3/8 SPP /2 SPP Sealing device Nylon washer Pneumatic output version 4 mm Push-in or 5 female thread Terminations Electric output version 3 core cable 0.5 mm 2 2 metres long Electronic output version 3 core cable 0. mm 2 2 metres long Working temperature From - 5 C to + 60 C Working pressure From 3 to 8 bar PTP4/8P - Pressure sensor - Pneumatic output with push-in connection C5 Part number C5 G H J Y Weight 0.5 fl4 fl4 Y G Y/2 H J 5x0.8 PTP8P /8 PTP4P4-/ /4 PTP4P4-/ /8 PTP4P4-3/ /2 PTP4P4-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 24 Catalogue UK

126 Y Pneumatic integrated function fittings PTP4/8 - Pressure sensor - Pneumatic output with 5 threaded connection 0.5 5x0.8 5x0.8 Y C5 Part number C5 G H J Y Weight G Y/2 H J 5x0.8 PTP /8 PTP4-/ /4 PTP4-/ /8 PTP4-3/ /2 PTP4-/ PWS- - Plug-in sensor - Electrical output Part number Weight Output Output Output function connection characteristics evel of protection IP-40 PWS Electrical 3 wires Contact OF ~ Ve = mm 2 2 to 230 V ~ /0 V lon 2 m 2 to 48 VCC/-5W Technical specification of model PWS- : breaking pressure = 0.5 bar connection : lack (K) lue (U) rown (N) U K N F PWS-E - Plug in sensor - Electronic output Part number Weight Output Output Output function connection characteristics PWS-E Type NC Electronic 3 wires PNP PWS-E 0.07 Type NO 0. mm 2 0/30 V-CC lon 2 m 75 m evel of protection IP-67 Technical specification of model PWS-E : Pilot release pressure = 0.5 bar connection : lack black(k) lue blue(u) brown rown (N) + N -3 U 2 K C N/C contact + N -3 U 4 K C N/O contact PWS- - anjo socket (with sensor locking clip) C5 Part number C5 J N N Y Weight Tool required J N N 5x0.8 PWS Flat spanner 8 mm /8 PWS llen key 5 mm /4 PWS llen key 8 mm 3/8 PWS llen key 0 mm /2 PWS llen key 2 mm llen screw ocking clip ll black pressure sensors are a combination of two distinct parts : a banjo socket + a plug-in sensor. anjo socket lack (K) lue (U) rown (N) Plug-in sensor rown (N) lue lack (U) (K) New part number PWS-02 + PWS-55 PWS-02 + PWS-88 PWS-02 + PWS-99 PWS-02 + PWS-33 PWS-02 + PWS-22 PWS-E0 + PWS-55 PWS-E0 + PWS-88 PWS-E0 + PWS-99 PWS-E0 + PWS-33 PWS-E0 + PWS-22 PWS-E + PWS-55 PWS-E + PWS-88 PWS-E + PWS-99 PWS-E + PWS-33 PWS-E + PWS-22 Old part number PTZ85 PTZ4-/8 PTZ4-/4 PTZ4-3/8 PTZ4-/2 PTE85 PTE4-/8 PTE4-/4 PTE4-3/8 PTE4-/2 PTE85C PTE4-/8C PTE4-/4C PTE4-3/8C PTE4-/2C F 25 Catalogue UK

127 Pneumatic integrated function fittings Prestostart - Pneumatic slow start fittings Principle System isolating valve Power valve Designed for mounting on either the FR or power valve, Parker Prestostart slow start function fittings permit the gradual increase in pressure to a section of the pneumatic system. This prevents shocks to the system that may occur when full system pressure is introduced thus reducing wear and potential damage to components. PIV Series - ounted on outlet port of FR to control downstream installation. - Initial flow through the bolt is controlled by a restrictor and adjustable needle valve. - When 2/3 rd system pressure is achieved the spring is compressed allowing immediate increase to full system pressure. - When the system is pressurised after an emergency stop all cylinders will return to the rest position. llen Key adjustment Gold identification washer Slow start regulator Spring djustable needle Valve FR To cylinder F PCV Series - ounted on the supply port of the power valve or on the common supply of associated power valves. - Initial flow into the power valve is controlled by the needle valve assembly. - When 2/3 rd system pressure is achieved the spring is compressed allowing immediate increase to full system pressure. - When the system is pressurised after an emergency stop all cylinders will return to the rest position. djustment by llen Key lack identification washer Pressure speed regulator Spring djustable needle Valve Power valve From FR From FR Pressurisation speed djustment of the needle valve to regulate the air flow controls the time taken to pressurise the system. Supply pressure P With slow-starter Without slow-starter djustable time Full Flow Time djustment - Use a spanner to prevent the bolt assembly turnin - Use an llen key to adjust the needle valve. aximum torque N/m. Spanner F 26 Catalogue UK

128 Pneumatic integrated function fittings Technical features Push-in version ody material Threaded version olt assembly material olt threads Sealing device Terminations Working temperature Working pressure High resistance polyamide rass nickel plated rass nickel plated /4 SPP 3/8 SPP /2 SPP Nylon washer 8 to 2 mm push-in /4 to /2 SPP female thread From - 5 C to + 70 C From 3 to 0 bar PCV4PK - Slow start fitting - Power valve version with push-in connection ir flow Part number C5 G H J Y Torque Nl/mn Kv Weight in. ax. mn at 6 bar C5 Y H H ax in J 8 /4 PCV4PK8-/ /4 PCV4PK0-/ /8 PCV4PK0-3/ F G Y/2 PCV4 - Slow start fitting - Power valve version with threaded connection ir flow Part number C5 G H J Y Torque Nl/mn Kv Weight in. ax. mn at 6 bar C5 H in H ax /4 PCV4-/ /8 PCV4-3/ Y J G Y/2 PIV4PK - Slow start fitting - System isolating valve version with push-in connection Torque ir flow Part number C5 G H J Y Nl/mn Kv Weight in. ax. mn at 6 bar C5 Y G H H ax in J 24/across flats 8 /4 PIV4PK8-/ /4 PIV4PK0-/ /8 PIV4PK0-3/ /8 PIV4PK2-3/ /2 PIV4PK2-/ Y/2 Specific to /2 size PIV4 - Slow start fitting - System isolating valve version with threaded connection Torque ir flow Part number C5 G H J Y Nl/mn Kv Weight mn min. max. at 6 bar C5 Y G Y/2 H in J H ax Specific to /2 size 24/across flats /4 PIV4-/ /8 PIV4-3/ /2 PIV4-/ Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). F 27 Catalogue UK

129 Pneumatic integrated function fittings Prestoreduce - Pressure reduction fittings Principle This function fitting is manually preset to provide the cylinder with optimum air pressure. This reduces the air consumption of the cylinder generating energy savings. This fitting is particularly suitable for cylinders used in cutting, pressing or gripping operations. - System pressure (Pi) is reduced by a spring-loaded valve which can be calibrated by the set screw. - The greater the reduction between inlet and outlet pressure the larger the energy savings. - The coloured indicator shows the energy savings achieved. - The purge vent allows rapid exhaust of air in emergencies. - djustment can be made with an llen key or manual ratchet control (see page F 29). - n anti tamper plug can be fitted after the pressure has been set (see page F 29). Poppet valve Pi Power valve Energy saving indicator djustable spring Check valve To the Pr cylinder Rapid exhaust vent F Pressure lignment between the level of saving shown by the indicator and that shown by the marking Pi system saving Pr reduced applied pressure Pr Energy setting Pi - Pr back pressure reversal of control valve start of cylinder stroke Pressure saving end of cylinder stroke Time yellow : maximum saving orange : high saving red : moderate saving 6 bar Pressure saving Pressure saving indication Pr Pr Pr - Out stroke 2 - End of stroke 3 - Return stroke F 28 Catalogue UK

130 Pneumatic integrated function fittings Technical features anjo version ody material In line version olt assembly material olt threads Sealing device Terminations Working temperature Working pressure etal Nickel plated brass rass /8 SPP /4 SPP 3/8 SPP /2 SPP Nylon Washer 6 to 0 mm Push-in /8 to /2 SPP female thread - 5 C to + 70 C bar to 8 bar PR4P - Pressure reducer - anjo version with push-in connection C5 G3 Y G G2 H H J Part number C5 G G2 G3 H H J Y Weight in. ax. 6 /8 PR4P6-/ /4 PR4P6-/ /4 PR4P8-/ /4 PR4P0-/ /8 PR4P0-3/ F Y/2 PR4 - Pressure reducer - anjo version with threaded connection C C5 G3 Y G G2 H H J Part number C C5 G G2 G3 H H J Y Weight in. ax. /8 PR4-/ /4 PR4-/ /8 PR4-3/ /2 PR4-/ Y/2 PRIP - Pressure reducer - In-line version with push-in connection W G2 H2 H H Part number G2 G3 H H H2 T W Weight in. ax. in. ax. 6 PRIP PRIP PRIP T G3 PRI4 - Pressure reducer - In-line version with threaded connection W C G2 H2 T G3 C2 H Part number C C2 G2 G3 H H H2 T W Weight in. ax. in. ax. /8 PRI4-/ /4 PRI4-/ /8 PRI4-3/ /2 PRI4-/ Parker Prestoflow with push-in connections are designed to be used with Parker calibrated polyamide or polyurethane tubin See Thermoplastic singles tubes & Pneumo-Tube bundles section (P). F 29 Catalogue UK

131 i Pneumatic integrated function fittings Prestosil - Silencer and flow control valve Principle Prestosil silencers are designed for mounting into the exhaust valve of single acting cylinders or on the directional control valve. Operation Noise reduction The escaping air is pre-expanded in the chamber of the silencer. It then flows through a sintered bronze cartridge whose design provides a complete expansion of the exhaust air. ale pipe thread Pre-expansion chamber with exhaust slots Flow control The adjusting screw of the uni- direction flow control valve allows fine adjustment of the restriction and thus precise control of the piston-rod speed. The setting is secured by a lock nut. Integrated fi t t n g ock nut Precision adjusting screw Sintered bronze cartridge F Technical features ody material Sinter material Needle valve material ocknut material Silencer thread Working temperature Working pressure luminium ronze luminium luminium /8 SPP /4 SPP 3/8 SPP /2 SPP From -25 C to + 00 C From 0. to 0 bar Noise reduction characteristics t an average working pressure of 5 bar the noise reduction achieved with the appropriate Prestosil model ranges from 22 to 37 d. Part number Working pressure bar 2 bar 3 bar 4 bar 5 bar 6 bar 7 bar PRS4-/8 PRS4-/4 PRS4-3/8 PRS4-/ PRS - Silencer and flow control valve Part number C O Weight in. ax. O C /8 PRS4-/ /4 PRS4-/ /8 PRS4-3/ /2 PRS4-/ F 30 Catalogue UK

132 Pneumatic integrated function fittings Non-return union PW- - Non-return equal union NEW Part number O ir flow Kv Weight at 6 bar NI/min O 4 PW PW PW ccessories - Flow control Clip - Flow control clips Ratchet 6 - manual ratchet Tube Part number Weight OD 4 Clip Clip Clip0-2 9 Suitable for in-line flow regulators PTF series F H Push Turn Tube Part number H Weight OD 6 RTCHET Suitable for use with pressure reducing fittings - PR/PRI F Splug - djuster plug D Setting secured D Part number Weight 8-6 SPUG PGUGE - Plug-in pressure gauge G2 4 6 bar D Part number G G2 Weight 6 PGUGE G D 0-0 bar The plug in pressure gauge enables the energy savings made with Prestoreduce fittings to be measured. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. F 3 Catalogue UK

133 etrulok rass fitting for copper and plastic tubing Catalogue 4324-UK

134 etrulok fitting Index Straight connectors male - NPT F - p. G 6 male - SPT F3 - p. G 6 male - SPP F4 - p. G 6 male - metric F8 - p. G 7 union H - p. G 7 female - NPT G - p. G 7 female - SPP G4 - p. G 8 ulkhead connectors union W - p. G 8 mixed union WP - p. G 8 90 elbows G male - NPT C - p. G 9 male - SPT C3 - p. G 9 adjustable male - metric C8 - p. G 9 union E - p. G 0 Tees union J - p. G 0 male run - NPT R - p. G 0 male run - SPT R3 - p. G male branch - NPT S - p. G male branch - SPT S3 - p. G Cross anjo union K - p. G 2 single - assembled SPP COR4 - p. G 2 Tube end adaptors male - NPT T2HF - p. G 2 male - SPT T23HF - p. G 3 male - metric T28HF - p. G 3 female - NPT T2HG - p. G 3 female - SPP T24HG - p. G 4 Connector accessories nut nut + ferrule - p. G 4 T - p. G 4 fitting body cap FN - p. G 4 tube plug PN - p. G 5 ferrule T - p. G 5 tube end reducer TR - p. G 5 tube insert T23U - p. G 5 G 2 Catalogue 4324-UK

135 etrulok fitting Principle etrulok is a one-piece, ready-to-use, bite type fitting with back compression. The ferrule is held captive in the nut. 2 3 The fitting is designed to permit tube entry and fitting make-up without removal of the nut and ferrule, avoiding assembly of the fitting components prior to use. Technical features G aterial 2 3 Working temperature Working pressure* depending on tube O.D. (with mm wall thickness) ody Nut Ferrule rass rass rass From - 60 C to + 90 C Tube O.D. mm to 22 bar * The pressures given are with copper tubin For polyamide or polyurethane tubing see Thermoplastic single tubes and Pneumo-Tube bundles section (P). pplications With its ability to be used with many types of tubing and its variety of thread forms, etrulok is suitable for a wide range of fluid applications. It is particularly suitable for arduous environments, with its wide temperature range and excellent vibration characteristics. Welding Washing equipment Heating systems utomotive Compressors achine tools G 3 Catalogue 4324-UK

136 etrulok fitting dvantages Fitting ready to use - Compact fully assembled fitting, saving time at installation. - Captive snap-in ferrule. - Simplified handling and stock control. - No pre-setting of the ferrule. Safety - Visible ferrule (extending through rear of nut) allows quality control checks for correct assembly. Excellent vibration resistance - Vibration is contained by the back compression of the ferrule extending outside the nut. - The tube is held at the bottom of the fittin The tube is thus held between two points so that vibration running along the tube does not affect the sealing and bite area. Wide variety of tubing etrulok can be used with copper tube conforming to DIN 786, NF S-20, S 287 Part 2. etrulok is suitable for use with most types of plastic tubing (polyamide, polyurethane, polyethylene, Pebax, Teflon...) Parker Push-ok hoses can also be connected with etrulok bodies using the Push-ok FF series connectors (see Push-ok Hose and Fittings section). G Forgings -etrulok shaped fittings are produced from hot forgings to meet exacting requirements. - The hot forging process increases the density of the material, refines the grain structure and improves material strength. Positive sealing and bite - The wedging action of the nut when tightened causes the ferrule to bite into the outside diameter of the tube wall for a leakproof connection. -With flexible tubing (polyurethane, PE or polyethylene), it is recommended is used a tube insert to ensure positive holding of the tube. G 4 Catalogue 4324-UK

137 etrulok fitting ssembly instructions Cut the tube square De-burr (copper tube) Insert the tube through the nut and ferrule until it bottoms G Finger tighten the nut Spanner tighten the nut (one turn, or one and half turns according to the size) Disassembly - remake The etrulok fitting can be assembled and disassembled at least 5 times. t each remake, hand tighten the nut, then spanner tighten /6 of a turn. Fitting dimensions Tube O.D. mm 2 etric straight thread 3 Inside diameter mm 4 Hex of nut mm 5 Tube entry body mm 6 Tube entry compl. fitting mm Spanner tightening in turns 4 8x /2 6 0x /2 8 2x /2 0 4x /2 2 6x /2 4 8x /2 6 22x x x x G 5 Catalogue 4324-UK

138 etrulok fitting F - ale connector - NPT C P C Part number C C P Weight 4 /6 F4-/ /8 F4-/ /8 F6-/ /4 F6-/ /8 F8-/ /4 F8-/ /4 F0-/ /8 F0-3/ /8 F2-3/ /2 F2-/ F3 - ale connector - SPT 4 3/8 F4-3/ /2 F4-/ /2 F6-/ /2 F8-/ /4 F20-3/ /4 F22-3/ G C P C Part number C C P Weight 4 /8 F34-/ /8 F36-/ /4 F36-/ /8 F38-/ /4 F38-/ /4 F30-/ /8 F30-3/ /8 F32-3/ /2 F32-/ /8 F34-3/ /2 F34-/ /8 F36-3/ /2 F36-/ /2 F38-/ /4 F320-3/ /4 F322-3/ F4 - ale connector - SPP C J C Part number C C J Weight 4 /8 F44-/ /8 F46-/ /4 F46-/ /4 F48-/ /4 F40-/ These parts are supplied with a copper seal. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 6 Catalogue 4324-UK

139 etrulok fitting F8 - ale connector - metric straight thread Part number C C J Weight J 4 5x0.8 F x.5 F x.5 F x.5 F x.5 F C C 6 6x.5 F x.5 F These parts are supplied with a copper seal. H - Equal union Part number C C Weight C C C 4 H H H H H G 4 H H H H H G - Female connector - NPT Part number C C P Weight C C 6 /8 G6-/ /4 G6-/ /8 G8-/ /4 G8-/ /4 G0-/ P 0 3/8 G0-3/ /8 G2-3/ /2 G2-/ /8 G4-3/ /2 G4-/ /2 G6-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 7 Catalogue 4324-UK

140 etrulok fitting G4 - Female connector - SPP Part number C C J Weight C C 4 /8 G44-/ /8 G46-/ /4 G46-/ /8 G48-/ /4 G48-/ J 0 /4 G40-/ /8 G40-3/ /8 G42-3/ /2 G42-/ /8 G44-3/ /2 G44-/ /2 G46-/ /2 G48-/ W - ulkhead union G Part number C C C4 2 W Weight ax. 4 W4 8x W6 0x W8 2x W0 4x W2 6x C C C 4 C W 4 W4 8x W6 22x W8 24x W20 26x W22 28x WP - ixed bulkhead equal union 2 W C O C 4 C 2 2 Part number C C2 C4 O W Weight ax x WP x WP x WP x WP x WP x WP This bulkhead fitting combines a Prestolok and etrulok connection to connect a copper tube with a plastic tube. For this conversion fitting please consult Prestolok section(d), for recommended working pressure and temperature. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 8 Catalogue 4324-UK

141 etrulok fitting C - 90 male elbow - NPT C P Y N Part number C N P Y Weight 4 /8 C4-/ /8 C6-/ /4 C6-/ /8 C8-/ /4 C8-/ /4 C0-/ /8 C0-3/ /8 C2-3/ /2 C2-/ /8 C4-3/ /2 C4-/ /2 C6-/ /2 C8-/ /4 C20-3/ /4 C22-3/ C3-90 male elbow - SPT G C P Y N Part number C N P Y Weight 4 /8 C34-/ /8 C36-/ /4 C36-/ /8 C38-/ /4 C38-/ /4 C30-/ /8 C30-3/ /8 C32-3/ /2 C32-/ /8 C34-3/ /2 C34-/ /2 C36-/ /2 C38-/ /4 C320-3/ /4 C322-3/ C8-90 adjustable male elbow - metric straight thread C C 4 Y J N Part number C C4 J N Y Weight 2 6x.5 C x.5 C x.5 C x.5 C x.5 C x.5 C These fittings are equiped with Nitrile O-Rin The temperature range for this fitting range is from -25 C to + 00 C. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 9 Catalogue 4324-UK

142 etrulok fitting E - 90 union elbow Part number C Y Weight C Y 4 E E E E E E E E E E J - Union tee Y C Part number C Y Weight 4 J J J J J G 4 J J J J J R - ale run tee - NPT Y N P Part number C N P Y Weight 6 /8 R6-/ /4 R6-/ /8 R8-/ /4 R8-/ /4 R0-/ C 0 3/8 R0-3/ /8 R2-3/ /2 R2-/ /8 R4-3/ /2 R4-/ /2 R6-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 0 Catalogue 4324-UK

143 etrulok fitting R3 - ale run tee - SPT Y N P Part number C N P Y Weight 6 /8 R36-/ /4 R36-/ /8 R38-/ /4 R38-/ /4 R30-/ C 0 3/8 R30-3/ /8 R32-3/ /2 R32-/ /8 R34-3/ /2 R34-/ /2 R36-/ S - ale branch tee - NPT Part number C N P Y Weight 6 /8 S6-/ /4 S6-/ /8 S8-/ /4 S8-/ /4 S0-/ G Y P C N 0 3/8 S0-3/ /8 S2-3/ /2 S2-/ /8 S4-3/ /2 S4-/ /2 S6-/ S3 - ale branch tee - SPT Part number C N P Y Weight 6 /8 S36-/ /4 S36-/ /8 S38-/ /4 S38-/ /4 S30-/ Y P C N 0 3/8 S30-3/ /8 S32-3/ /2 S32-/ /8 S34-3/ /2 S34-/ /2 S36-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G Catalogue 4324-UK

144 etrulok fitting K - Union cross Part number C Y Weight 6 K K K K K K Y C COR4 - Single banjo SPP G Part number C C5 J N N Weight C J C 5 N N 4 /8 COR44-/ /4 COR46-/ /4 COR48-/ /2 COR44-/ /2 COR46-/ /2 COR48-/ /4 COR420-3/ /4 COR422-3/ These parts are supplied with peripheral seals. T2HF - Tube end male adaptor - NPT Part number C P Weight P C 6 /8 T2HF6-/ /4 T2HF6-/ /8 T2HF8-/ /4 T2HF8-/ /4 T2HF0-/ /8 T2HF0-3/ /8 T2HF2-3/ /2 T2HF2-/ /8 T2HF4-3/ /2 T2HF4-/ /2 T2HF6-/ /2 T2HF8-/ /4 T2HF20-3/ /4 T2HF22-3/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 2 Catalogue 4324-UK

145 etrulok fitting T23HF - Tube end male adaptor - SPT Part number C P Weight 6 /8 T23HF6-/ /4 T23HF6-/ /8 T23HF8-/ /4 T23HF8-/ /4 T23HF0-/ P C 0 3/8 T23HF0-3/ /8 T23HF2-3/ /2 T23HF2-/ /8 T23HF4-3/ /2 T23HF4-/ /2 T23HF6-/ /2 T23HF8-/ /4 T23HF20-3/ /4 T23HF22-3/ T28HF - Tube end male adaptor - metric straight thread G Part number C J Weight 2 4x.5 T28HF x.5 T28HF x.5 T28HF x.5 T28HF x.5 T28HF J C 4 22x.5 T28HF x.5 T28HF x.5 T28HF x.5 T28HF T2HG - Tube end female adaptor - NPT Part number C P Weight C 6 /8 T2HG6-/ /4 T2HG6-/ /8 T2HG8-/ /4 T2HG8-/ /4 T2HG0-/ P 0 /2 T2HG0-/ /8 T2HG0-3/ /8 T2HG2-3/ /2 T2HG2-/ /8 T2HG4-3/ /2 T2HG4-/ /2 T2HG6-/ /2 T2HG8-/ /4 T2HG20-3/ /4 T2HG22-3/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. G 3 Catalogue 4324-UK

146 etrulok fitting T24HG - Tube end female adaptor - SPP Codice C J Peso 6 /8 T24HG6-/ /4 T24HG6-/ /8 T24HG8-/ /4 T24HG8-/ /4 T24HG0-/ /8 T24HG0-3/ /8 T24HG2-3/ /2 T24HG2-/ /8 T24HG4-3/ /2 T24HG4-/ /2 T24HG6-/ /2 T24HG8-/ /4 T24HG20-3/ /4 T24HG22-3/ C J - Nut C Tube Part number C Weight G T - Nut + ferrule C Tube Part number C Weight 4 T T T T T T T T T T FN - Fitting body cap For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. C Tube Part number C Weight 4 FN FN FN FN FN FN FN FN FN FN G 4 Catalogue 4324-UK

147 etrulok fitting PN - Tube plug J C Tube Part number C J Weight 4 PN PN PN PN PN PN PN PN PN PN T - Ferrule TR - Tube end reducer Tube Part number Weight 4 T4 0 6 T6 0 8 T T T T T T T T G 2 C Composed of : a reduction cone, a special nut and a standard ferrule. 2 Part number C Weight 6 4 TR TR TR TR TR TR TR TR TR TR TR TR TR TR T23U - Tube insert R With plastic tubing, except polyamide or 2, we recommend the use of a tube insert for positive holding of the tube. Tube inserts are available for alternative C Tube Part number C R Weight ±0.50 axi 4/6 T23U /8 T23U /0 T23U /2 T23U /4 T23U G 5 Catalogue 4324-UK

148 P Nickel plated brass fitting for plastic tubing Catalogue 007-UK

149 P fitting H H 2 Catalogue 007-UK

150 P fitting Index Straight connectors male - NPT FP - p. H 6 male - SPT F3P - p. H 6 male - SPP F4P - p. H 7 male - metric F8P - p. H 7 union HP - p. H 7 ulkhead connectors union WP - p. H 7 90 elbows male - NPT CP - p. H 8 male - SPT C3P - p. H 8 male - SPP C4P - p. H 8 male - metric C8P - p. H 9 Tees H union JP - p. H 9 male run - NPT RP - p. H 9 male run - SPT R3P - p. H 9 male branch - NPT SP - p. H 0 male branch - SPT S3P - p. H 0 anjo single / assembled SPP COR4P - p. H Nut nut P - p. H H 3 Catalogue 007-UK

151 P fitting Principle P is a two piece nickel plated brass fitting specifically designed for flexible tubing such as polyamide, polyurethane, PE, polyethylene, PTFE, PVC, etc. 2 The seal is obtained by the bead formed at the tube end when the nut is tightened to the fitting body. The connection is leakproof to the burst pressure of the tube. P fittings can be assembled and disassembled repeatedly. Technical features aterial 2 Working pressure* Working temperature H ody Nickel plated brass Nut Nickel plated brass From 0.0 to 40 bar From - 40 C to + 00 C * The pressures given are with polyamide tubin For other tubing please consult us. pplications The P fitting's unique sealing method make it ideally suited for use with a wide variety of media. It is particularly suitable for use in fluid handling applications where media or temperature considerations limit the method of sealin Welding Food industry aboratory equipment Chemical industry Packaging achine tools H 4 Catalogue 007-UK

152 P fitting dvantages aximum tensile pull out force of polyamide tube from a P fitting Tube I.D./O.D. mm Tensile force dan 2.7/4 4/6 4 6/ /0 88 8/0 67 0/2 79 /4 49 Tube nut design - Compact for fast and safe assembly - Knurled nut facilitates finger tightenin - positive stop prevents overtightenin Rapid assembly P fittings can be assembled finger tight when used with soft tubing e. polyurethane, polyethylene, etc. This facilitates rapid assembly and disassembly. Excellent pull out resistance The clamping of the tube between the spigot of the P fitting body and the tube nut creates an effective seal with a high pull out performance. This is particularly useful in severe operating conditions. The chart above indicates the average pull out values for polyamide tubing when used with a P fittin H ssembly instructions Cut the tube square Insert the tube through the nut Push the tube over the spigot of the fitting until it comes into contact with the stop Finger tighten the nut to the end stop when using soft tubin Tighten the nut with a spanner to the end stop when using semi-rigid tubin H 5 Catalogue 007-UK

153 P fitting Fitting dimensions Tube I.D./O.D. mm 2 etric pipe thread 3 Inside diameter mm 4 Hex of nut mm 5 Tube entry mm 2.7/4 6x /6 9x /8 x /0 3x /0 3x /2 5x /4 8x FP - ale connector - NPT H C P C Part number C C P Weight 2.7/4 /8 FP2.7/4-/ /6 /8 FP4/6-/ /6 /4 FP4/6-/ /8 /8 FP6/8-/ /8 /4 FP6/8-/ /0 /4 FP8/0-/ /0 3/8 FP8/0-3/ /2 3/8 FP0/2-3/ F3P - ale connector - SPT C P C Part number C C P Weight 2.7/4 /8 F3P2.7/4-/ /6 /8 F3P4/6-/ /6 /4 F3P4/6-/ /8 /8 F3P6/8-/ /8 /4 F3P6/8-/ /8 3/8 F3P6/8-3/ /0 /4 F3P7.5/0-/ /0 3/8 F3P7.5/0-3/ /0 /4 F3P8/0-/ /0 3/8 F3P8/0-3/ /2 3/8 F3P0/2-3/ /4 3/8 F3P/4-3/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. H 6 Catalogue 007-UK

154 P fitting F4P - ale connector - SPP J Part number C C J Weight 4/6 /8 F4P4/6-/ /8 /4 F4P6/8-/ These parts are supplied with a copper seal. C C F8P - ale connector - metric straight thread J Part number C C J Weight 6/8 0x F8P6/ /8 2x.25 F8P6/ These parts are supplied with a copper seal. C C H HP - Equal union C C C Part number C C Weight 2.7/4 HP2.7/ /6 HP4/ /8 HP6/ /0 HP8/ /2 HP0/ /4 HP/ WP - ulkhead union C C C 4 W C Part number C C C4 W Weight 4/6 WP4/6 9x /8 WP6/8 x /0 WP8/0 3x /2 WP0/2 5x /4 WP/4 8x For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. H 7 Catalogue 007-UK

155 P fitting CP - 90 male elbow - NPT C Y P N Part number C N P Y Weight 2.7/4 /8 CP2.7/4-/ /6 /8 CP4/6-/ /6 /4 CP4/6-/ /8 /8 CP6/8-/ /8 /4 CP6/8-/ /0 /4 CP8/0-/ /0 3/8 CP8/0-3/ /2 3/8 CP0/2-3/ C3P - 90 male elbow - SPT C Y P N Part number C N P Y Weight 2.7/4 /8 C3P2.7/4-/ /6 /8 C3P4/6-/ /6 /4 C3P4/6-/ /8 /8 C3P6/8-/ /8 /4 C3P6/8-/ /8 3/8 C3P6/8-3/ /0 /4 C3P7.5/0-/ /0 3/8 C3P7.5/0-3/ /0 /4 C3P8/0-/ /0 3/8 C3P8/0-3/ H 0/2 3/8 C3P0/2-3/ /4 3/8 C3P/4-3/ C4P - 90 male elbow - SPP Y Part number C C4 J N Y Weight 6/8 /4 C4P6/8-/ C C 4 J N These fittings are supplied with nitrile seals. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. H 8 Catalogue 007-UK

156 P fitting C8P - 90 male elbow - metric straight thread Y Part number C C4 J N Y Weight C C 4 J N 6/8 0x C8P6/ /8 2x C8P6/ These fittings are supplied with nitrile seals. JP - Union tee C Y Part number C Y Weight 2.7/4 JP2.7/ /6 JP4/ /8 JP6/ /0 JP7.5/ /0 JP8/ /2 JP0/ /4 JP/ H RP - ale run tee - NPT C Y N P Part number C N P Y Weight 4/6 /8 RP4/6-/ /6 /4 RP4/6-/ /8 /4 RP6/8-/ R3P - ale run tee - SPT C Y N P Part number C N P Y Weight 4/6 /8 R3P4/6-/ /6 /4 R3P4/6-/ /8 /8 R3P6/8-/ /8 /4 R3P6/8-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. H 9 Catalogue 007-UK

157 P fitting SP - ale branch tee - NPT C Y P N Part number C N P Y Weight 4/6 /8 SP4/6-/ /6 /4 SP4/6-/ /8 /4 SP6/8-/ S3P - ale branch tee - SPT C Y P N Part number C N P Y Weight 4/6 /8 S3P4/6-/ /6 /4 S3P4/6-/ /8 /8 S3P6/8-/ /8 /4 S3P6/8-/ H COR4P - Single banjo - SPP C J C 5 N N Part number C C5 J N N Weight 4/6 /8 COR4P4/6-/ /6 /4 COR4P4/6-/ /8 /8 COR4P6/8-/ /8 /4 COR4P6/8-/ These parts are supplied with peripheral seals. The banjo bolt is made of steel. P - Nut C Part number C Weight 2.7/4 P /6 P /8 P /0 P /0 P /2 P /4 P For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. H 0 Catalogue 007-UK

158 Ermeto Original ite Type Tube Fitting Systems Catalogue 400--UK

159 Ermeto Original I I 2 Catalogue 400--UK

160 Ermeto Original Index Union G p. I 7 ocknut djustables SPP thread WEE-R TEE-R EE-R VEE-R p. I 20 p. I 2 p. I 22 p. I 23 Union Elbow ocknut djustables metric thread W p. I 8 WEE- TEE- EE- VEE- p. I 24 p. I 25 p. I 26 p. I 27 Union Tee T p. I 9 ocknut djustables UNF/UN thread WEE-UNFTEE-UNF EE-UNF VEE-UNF p. I 28 p. I 29 p. I 30 p. I 3 ale Stud Connector SPP thread EO-2 Functional Nut GE-R-ED p. I 0- F p. I ale Stud Connector etric thread GE--ED p. I 2-3 Nut Progressive Ring Cutting Ring.DPR.D p. I I ale Stud Connector UNF/UN thread GE-UNF/UN p. I 4-5 ulkhead Fitting Nut G p. I 36 ulkhead Union lanking Plug for fitting cones SV p. I 6 VK p. I 37 Swivel Nut Elbow Fitting lanking Plug for ports EW p. I 7 VSTI-R/-ED p. I 38 Swivel Nut ranch Tee Fitting ET p. I 8 Support Sleeve for plastic tubes E p. I 39 Swivel Nut Run Tee Fitting E p. I 9 SensoControl SC-50 p. I 40 to 43 I 3 Catalogue 400--UK

161 Ermeto Original EO Tube Fitting Systems EO-2 - Dry Technology efore assembly DPR - Progressive Ring fter assembly Steel with NR sealing or Stainless steel.457 with FP sealing I efore assembly D - Cutting Ring fter assembly Steel or Stainless steel.457 efore assembly fter assembly rass I 4 Catalogue 400--UK

162 Ermeto Original Pressure Ratings Nominal Pressure PN The Nominal Pressure PN is a figure relating to the pressure rating of a fluid component for continuous dynamic applications. It is rounded to correspond to internationally standardised ratings. ogical series of fittings are grouped together, with the nominal pressure of the group being that of the lowest common denominator within the group. Internationally, these nominal pressures are recognised and serve to match common sizes of components together. Parts with a stated PN value are able to withstand normal, non-continuous pressure peaks from PN to the P max value. To prove the long term dynamic load resistance, components are tested under impulse conditions of PN.33, at Hz for million cycles. P P max PN GRPHIC IUSTRTION OF PN ND P max urst Pressure = min. PN 4 for limited duration applications for normal applications TIE t P max P max is the maximum working pressure of a component including the pressure peaks, for limited duration applications. If a component is used over the full dynamic range from zero pressure to P max, it will withstand at least 200,000 cycles leakfree. Static burst test pressures are at least 2.5 times the P max value. Components are tested under impulse conditions of P max, at Hz for 200,000 cycles. Note: The older catalogue designation of P will be renamed P max. Parts that are involved will have P max values equal to the old P values (shown in only one column). The rating is involved are still the maximum level of continuous dynamic load. Temperature range for sealing materials NR (e. Perbunan) 35 to +00 C FP (e. PTFE) 25 to +200 C Perbunan = registered trademark of ayer. The temperature limits specified for sealing materials are approximate values, since the temperature limits can be greatly influenced by the medium. I When combining the different fitting and sealing materials, the lowest temperature limit in each case is applicable. I 5 Catalogue 400--UK

163 Ermeto Original Pressure reductions Pressure ratings PN and Pmax have to be reduced according to temperature Fitting aterial Temperatur Range Pressure Reduction Steel 40 to +20 C rass 60 to +75 C 35 % Stainless Steel to +20 C Stainless Steel C 4% Stainless Steel C % Stainless Steel C 20 % Stainless Steel C 29 % Stainless Steel C 33 % Intermediate values are to be interpolated. If the tube material used deviates from the fitting material, the tube is to be checked seaparately with regard to the permissible temperature range and the pressure reductions required. ale stud fittings may require additional pressure reductions, due to the mating port material and the sealing system must also be taken into account. I If different stipulations for special applications are made by standards, regulations or approvals with regard to permissible pressure reductions to be applied if necessary, then these stipulations made are bindin These pressure and safety specifications are based on all assemblies being in accordance with Parker-Ermeto instructions. It is further assumed that the tube routing will be laid and clamped in such a fashion that no additional stress, load or tension may act on the fittings. Tube fixtures are to be laid with sufficient stability according to the operating conditions and connected with supports. EO tube clamps are recommended for simple, problemfree assembly. I 6 Catalogue 400--UK

164 Ermeto Original G - Union EO tube end / EO tube end S l S 2 Series Tube PN P max l S S 2 Weight O.D. (bar) (bar) / piece Series Tube Dry Technology Dry Technology O.D. EO-2 steel DPR steel* EO-2 stainless steel DPR stainless steel* D brass 04 G04Z3C G043C G047 G04S 06 G06Z3C G063C G067 G06S 08 G083C G087 G08S 0 G03C G07 G0S 2 G23C G27 G2S 06 G06Z3C G063C G06Z7 G067 G06S 08 G08Z3C G083C G08Z7 G087 G08S 0 G0Z3C G03C G0Z7 G07 G0S 2 G2Z3C G23C G2Z7 G27 G2S 5 G5Z3C G53C G5Z7 G57 G5S 8 G8Z3C G83C G8Z7 G87 G8S 22 G22Z3C G223C G22Z7 G227 G22S 28 G28Z3C G283C G28Z7 G287 G28S 35 G35Z3C G353C G35Z7 G357 G35S 42 G42Z3C G423C G42Z7 G427 G42S I Without nut and ring: Example G063CX G063CX G067X G067X G06SX *Series with D-rin I 7 Catalogue 400--UK

165 Ermeto Original W - Union Elbow EO tube end / EO tube end S 3 S 3 S 2 Profile body (steel and brass): Series 4 2 mm Tube O.D. Series 6 2 mm Tube O.D. S 2 l 2 2 Series Tube PN P max 2 l 2 S 2 S 3 S 3 ** Weight O.D. (bar) (bar) / piece **only stainless steel l 2 2 I Series Tube Dry Technology Dry Technology O.D. EO-2 steel DPR steel* EO-2 stainless steel DPR stainless steel* D brass 04 W04Z3C W043C W047 W04S 06 W06Z3C W063C W067 W06S 08 W083C W087 W08S 0 W03C W07 W0S 2 W23C W27 W2S 06 W06Z3C W063C W06Z7 W067 W06S 08 W08Z3C W083C W08Z7 W087 W08S 0 W0Z3C W03C W0Z7 W07 W0S 2 W2Z3C W23C W2Z7 W27 W2S 5 W5Z3C W53C W5Z7 W57 W5S 8 W8Z3C W83C W8Z7 W87 W8S 22 W22Z3C W223C W22Z7 W227 W22S 28 W28Z3C W283C W28Z7 W287 W28S 35 W35Z3C W353C W35Z7 W357 W35S 42 W42Z3C W423C W42Z7 W427 W42S Without nut and ring: Example W063CX W063CX W067X W067X W06SX *Series with D-rin I 8 Catalogue 400--UK

166 Ermeto Original T - Union Tee ll 3 ends EO tube end S 2 S 3 Series Tube PN P max 2 I 2 S 2 S 3 S 3 ** Weight O.D. (bar) (bar) / piece Profile body (steel and brass): Series 4 0 mm Tube O.D. Series 6+8 mm Tube O.D. S 2 S 3 I 2 2 **only stainless steel I 2 2 I Series Tube Dry Technology Dry Technology O.D. EO-2 steel DPR steel* EO-2 stainless steel DPR stainless steel* D brass 04 T04Z3C T043C T047 T04S 06 T06Z3C T063C T067 T06S 08 T083C T087 T08S 0 T03C T07 T0S 2 T23C T27 T2S 06 T06Z3C T063C T06Z7 T067 T06S 08 T08Z3C T083C T08Z7 T087 T08S 0 T0Z3C T03C T0Z7 T07 T0S 2 T2Z3C T23C T2Z7 T27 T2S 5 T5Z3C T53C T5Z7 T57 T5S 8 T8Z3C T83C T8Z7 T87 T8S 22 T22Z3C T223C T22Z7 T227 T22S 28 T28Z3C T283C T28Z7 T287 T28S 35 T35Z3C T353C T35Z7 T357 T35S 42 T42Z3C T423C T42Z7 T427 T42S Without nut and ring: Example T063CX T063CX T067X T067X T06SX *Series with D-rin I 9 Catalogue 400--UK

167 Ermeto Original GE-R-ED - ale Stud Connector EO tube end / ale SPP thread DIN 3852, Form E: Eolastic Seal ED S S 2 d 7 G i l Series Tube G PN P max l i S 2 S d 7 Weight O.D. (bar) (bar) / piece 04 G/ G/ G/ G/ G3/ G/ G/ G/ G3/ G/ G/ G/ G3/ G/ G3/ G/ G/ G/ G3/ G/ G3/ G3/ G/ G3/ G3/ G3/ G/ G G G3/ G/ G/ G G/ G/ G G/ I I 0 Catalogue 400--UK

168 Ermeto Original GE-R-ED - ale Stud Connector EO tube end / ale SPP thread DIN 3852, Form E: Eolastic Seal ED S S 2 d 7 G i l Series Tube G Dry Technology Dry Technology O.D. EO-2 steel DPR steel* EO-2 stainless steel DPR stainless steel* D brass 04 R/8 GE04ZRED3C GE04RED3C GE04RED7 06 R/8 GE06ZRED3C GE06RED3C GE06RED7 06 G/8 GE06ZRED3C GE06RED3C GE06ZRED7 GE06RED7 GE06REDS 06 G/4 GE06ZR/4ED3C GE06R/4ED3C GE06ZR/4ED7 GE06R/4ED7 06 G3/8 GE06ZR3/8ED3C GE06R3/8ED3C GE06ZR3/8ED7 GE06R3/8ED7 06 G/2 GE06ZR/2ED3C GE06R/2ED3C GE06ZR/2ED7 GE06R/2ED7 08 G/4 GE08ZRED3C GE08RED3C GE08ZRED7 GE08RED7 GE08REDS 08 G/8 GE08ZR/8ED3C GE08R/8ED3C GE08ZR/8ED7 GE08R/8ED7 08 G3/8 GE08ZR3/8ED3C GE08R3/8ED3C GE08ZR3/8ED7 GE08R3/8ED7 08 G/2 GE08ZR/2ED3C GE08R/2ED3C GE08ZR/2ED7 GE08R/2ED7 0 G/4 GE0ZRED3C GE0RED3C GE0ZRED7 GE0RED7 GE0REDS 0 G/8 GE0ZR/8ED3C GE0R/8ED3C GE0ZR/8ED7 GE0R/8ED7 0 G3/8 GE0ZR3/8ED3C GE0R3/8ED3C GE0ZR3/8ED7 GE0R3/8ED7 0 G/2 GE0ZR/2ED3C GE0R/2ED3C GE0ZR/2ED7 GE0R/2ED7 2 G3/8 GE2ZRED3C GE2RED3C GE2ZRED7 GE2RED7 GE2REDS 2 G/8 GE2ZR/8ED7 GE2R/8ED7 2 G/4 GE2ZR/4ED3C GE2R/4ED3C GE2ZR/4ED7 GE2R/4ED7 2 G/2 GE2ZR/2ED3C GE2R/2ED3C GE2ZR/2ED7 GE2R/2ED7 2 G3/4 GE2ZR3/4ED3C GE2R3/4ED3C 5 G/2 GE5ZRED3C GE5RED3C GE5ZRED7 GE5RED7 GE5REDS 5 G3/8 GE5ZR3/8ED3C GE5R3/8ED3C GE5ZR3/8ED7 GE5R3/8ED7 5 G3/4 GE5ZR3/4ED3C GE5R3/4ED3C GE5ZR3/4ED7 GE5R3/4ED7 8 G/2 GE8ZRED3C GE8RED3C GE8ZRED7 GE8RED7 GE8REDS 8 G3/8 GE8ZR3/8ED3C GE8R3/8ED3C GE8ZR3/8ED7 GE8R3/8ED7 8 G3/4 GE8ZR3/4ED3C GE8R3/4ED3C GE8ZR3/4ED7 GE8R3/4ED7 22 G3/4 GE22ZRED3C GE22RED3C GE22ZRED7 GE22RED7 GE22REDS 22 G/2 GE22ZR/2ED3C GE22R/2ED3C GE22ZR/2ED7 GE22R/2ED7 22 G GE22ZRED3C GE22RED3C GE22ZRED7 GE22RED7 28 G GE28ZRED3C GE28RED3C GE28ZRED7 GE28RED7 GE28REDS 28 G3/4 GE28ZR3/4ED3C GE28R3/4ED3C GE28ZR3/4ED7 GE28R3/4ED7 28 G/4 GE28ZR/4ED3C GE28R/4ED3C GE28ZR/4ED7 GE28R/4ED7 35 G/4 GE35ZRED3C GE35RED3C GE35ZRED7 GE35RED7 GE35REDS 35 G GE35ZRED3C GE35RED3C GE35ZRED7 GE35RED7 35 G/2 GE35ZR/2ED7 GE35R/2ED7 42 G/2 GE42ZRED3C GE42RED3C GE42ZRED7 GE42RED7 GE42REDS 42 G GE42ZRED7 GE42RED7 42 G/4 GE42ZR/4ED7 GE42R/4ED7 Without nut and ring: Example GE06REDOD3C GE06REDOD7 GE06REDODS GE06REDOD3C GE06REDOD7 *Series with D-rin I I Catalogue 400--UK

169 Ermeto Original GE--ED - ale Stud Connector EO tube end / ale metric parallel thread with Eolastic seal ED S S 2 d 7 G i l Series Tube G PN P max l i S 2 S d 7 Weight O.D. (bar) (bar) / piece I I 2 Catalogue 400--UK

170 Ermeto Original GE--ED - ale Stud Connector EO tube end / ale metric parallel thread with Eolastic seal ED S S 2 d 7 G i l Series Tube G Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel 06 0x GE06ZED3C GE06ED3C GE06ZED7 GE06ED7 08 2x.5 GE08ZED3C GE08ED3C GE08ZED7 GE08ED7 0 4x.5 GE0ZED3C GE0ED3C GE0ZED7 GE0ED7 0 2x.5 GE0Z2x.5ED7 GE02X.5ED7 0 6x.5 GE0Z6X.5ED3C GE06X.5ED3C GE0Z6x.5ED7 GE06X.5ED7 0 8x.5 GE0Z8X.5ED3C GE08X.5ED3C 0 22x.5 GE0Z22X.5ED3C GE022X.5ED3C 2 6x.5 GE2ZED3C GE2ED3C GE2ZED7 GE2ED7 2 4x.5 GE2Z4X.5ED3C GE24X.5ED3C 2 8x.5 GE2Z8X.5ED3C GE28X.5ED3C 2 22x.5 GE2Z22X.5ED3C GE222X.5ED3C 5 8x.5 GE5ZED3C GE5ED3C GE2ZED7 GE5ED7 5 6x.5 GE5Z6X.5ED3C GE56X.5ED3C 5 22x.5 GE5Z22X.5ED3C GE522X.5ED3C 8 22x.5 GE8ZED3C GE8ED3C GE8ZED7 GE8ED7 8 8x.5 GE8Z8X.5ED3C GE88X.5ED3C 22 26x.5 GE22ZED3C GE22ED3C GE22ZED7 GE22ED x.5 GE22Z22X.5ED3C GE2222X.5ED3C 28 33x2 GE28ZED3C GE28ED3C GE28ZED7 GE28ED x2 GE35ZED3C GE35ED3C GE35ZED7 GE35ED x2 GE42ZED3C GE42ED3C GE42ZED7 GE42ED7 I Without nut and ring: Example GE06EDOD3C GE06EDOD3C GE06EDOD7 GE06EDOD7 *Series with D-rin I 3 Catalogue 400--UK

171 Ermeto Original GE-UNF/UN - ale Stud Connector EO tube end / UNF/UN parallel thread with O-ring seal S S 2 d 3 G i I O-Ring Series Tube G PN P max d 3 i I S S 2 O-ring Weight O.D. (bar) (bar) Shore-Hardness / piece approx /6-20UNF OR8.92X.83X /6-20UNF OR8.92X.83X /6-8UNF OR.9X.98X /4-6UNF OR6.36X2.20X /8-4UNF OR9.8X2.46X /4-6UNF OR6.36X2.20X /8-4UNF OR9.8X2.46X 2 8 3/4-6UNF OR6.36X2.20X /8-4UNF OR9.8X2.46X /8-4UNF OR9.8X2.46X /6-2UN OR23.47X2.95X /6-2UN OR29.74X2.95X /6-2UN OR23.47X2.95X /6-2UN OR29.74X2.95X /6-2UN OR37.46X2.95X /8-2UN OR37.46X3X /8-2UN OR37.46X3X 578 I O-ring FP: Example OR8.92X.83VITX I 4 Catalogue 400--UK

172 Ermeto Original GE-UNF/UN - ale Stud Connector EO tube end / UNF/UN parallel thread with O-ring seal S S 2 d 3 G i I O-Ring Series Tube G Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel 08 7/6-20UNF-2 GE08Z7/6UNF3C GE087/6UNF3C GE08Z7/6UNF7 GE087/6UNF7 0 7/6-20UNF-2 GE0Z7/6UNF3C GE07/6UNF3C GE0Z7/6UNF7 GE07/6UNF7 2 9/6-8UNF-2 GE2Z9/6UNF3C GE29/6UNF3C GE2Z9/6UNF7 GE29/6UNF7 2 3/4-6UNF-2 GE2Z3/4UNF3C GE23/4UNF3C GE2Z3/4UNF7 GE23/4UNF7 2 7/8-4UNF-2 GE2Z7/8UNF3C GE27/8UNF3C GE2Z7/8UNF7 GE27/8UNF7 5 3/4-6UNF-2 GE5Z3/4UNF3C GE53/4UNF3C GE5Z3/4UNF7 GE53/4UNF7 5 7/8-4UNF-2 GE5Z7/8UNF3C GE57/8UNF3C GE5Z7/8UNF7 GE57/8UNF7 8 3/4-6UNF-2 GE8Z3/4UNF3C GE83/4UNF3C GE8Z3/4UNF7 GE83/4UNF7 8 7/8-4UNF-2 GE8Z7/8UNF3C GE87/8UNF3C GE8Z7/8UNF7 GE87/8UNF7 22 7/8-4UNF-2 GE22Z7/8UNF3C GE227/8UNF3C GE22Z7/8UNF7 GE227/8UNF7 22 /6-2UN-2 GE22Z/6UN3C GE22/6UN3C GE22Z/6UNF7 GE22/6UNF7 22 5/6-2UN-2 GE22Z5/6UN3C GE225/6UN3C GE22Z5/6UNF7 GE225/6UNF7 28 /6-2UN-2 GE28Z/6UN3C GE28/6UN3C GE28Z/6UNF7 GE28/6UNF7 28 5/6-2UN-2 GE28Z5/6UN3C GE285/6UN3C GE28Z5/6UNF7 GE285/6UNF7 35 5/6-2UN-2 GE35Z5/6UN3C GE355/6UN3C GE35Z5/6UNF7 GE355/6UNF7 35 5/8-2UN-2 GE35Z5/8UN3C GE355/8UN3C GE35Z5/8UNF7 GE355/8UNF7 42 5/8-2UN-2 GE42Z5/8UN3C GE425/8UN3C GE42Z5/8UNF7 GE425/8UNF7 I Without nut and ring: Example GE087/6UNFOD3C GE087/6UNFOD7 GE087/6UNFOD3C GE087/6UNFOD7 I 5 Catalogue 400--UK

173 Ermeto Original SV - ulkhead Union EO tube end / EO tube end S S 4 S 2 D l l 3 3 D = 6 mm max. Series Tube PN P max S S 2 S 4 l 3 l 3 Weight O.D. (bar) (bar) / piece I Series Tube Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel D brass 06 SV06Z3C SV063C SV06Z7 SV067 SV06S 08 SV08Z3C SV083C SV08Z7 SV087 SV08S 0 SV0Z3C SV03C SV0Z7 SV07 SV0S 2 SV2Z3C SV23C SV2Z7 SV27 SV2S 5 SV5Z3C SV53C SV5Z7 SV57 SV5S 8 SV8Z3C SV83C SV8Z7 SV87 SV8S 22 SV22Z3C SV223C SV22Z7 SV227 SV22S 28 SV28Z3C SV283C SV28Z7 SV287 SV28S 35 SV35Z3C SV353C SV35Z7 SV SV42Z3C SV423C SV42Z7 SV427 Without nut and ring: Example SV06OD3C SV06OD3C SV06OD7 SV06OD7 SV06ODS I 6 Catalogue 400--UK

174 Ermeto Original EW - Swivel Nut Elbow EO tube end / EO Swivel l S 3 S 2 S 2 l 2 O-ring D d Series Tube d PN P max l l 2 S 2 S 3 O-ring Weight O.D. (bar) (bar) Shore-Hardness / piece approx OR4.5X.5X OR6.5X.5X OR8X.5X OR0X.5X OR2X2X OR5X2X OR20X2X OR26X2X OR32X2.5X OR38X2.5X 08 I O-ring FP Example OR4.5X.5VITX Series Tube d Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel EW06Z3C EW063C EW06Z7 EW EW08Z3C EW083C EW08Z7 EW EW0Z3C EW03C EW0Z7 EW EW2Z3C EW23C EW2Z7 EW EW5Z3C EW53C EW5Z7 EW EW8Z3C EW83C EW8Z7 EW EW22Z3C EW223C EW22Z7 EW EW28Z3C EW283C EW28Z7 EW EW35Z3C EW353C EW35Z7 EW EW42Z3C EW423C EW42Z7 EW427 Without nut and ring: Example EW06OD3C EW06OD3C EW06OD7 EW06OD7 I 7 Catalogue 400--UK

175 Ermeto Original ET - Swivel Nut ranch Tee EO tube ends / EO Swivel S 2 S 3 l S 2 l 2 D d O-ring* Series Tube d PN P max l l 2 S 2 S 3 O-ring Weight O.D. (bar) (bar) Shore-Hardness / piece approx OR4.5X.5X OR6.5X.5X OR8X.5X OR0X.5X OR2X2X OR5X2X OR20X2X OR26X2X OR32X2.5X OR38X2.5X 464 I O-ring FP Example OR4.5X.5VITX Series Tube d Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel ET06Z3C ET063C ET06Z7 ET ET08Z3C ET083C ET08Z7 ET ET0Z3C ET03C ET0Z7 ET ET2Z3C ET23C ET2Z7 ET ET5Z3C ET53C ET5Z7 ET ET8Z3C ET83C ET8Z7 ET ET22Z3C ET223C ET22Z7 ET ET28Z3C ET283C ET28Z7 ET ET35Z3C ET353C ET35Z7 ET ET42Z3C ET423C ET42Z7 ET427 Without nut and ring: Example ET06OD3C ET06OD3C ET06OD7 ET06OD7 I 8 Catalogue 400--UK

176 Ermeto Original E - Swivel Nut Run Tee EO tube ends / EO Swivel l S 2 l 2 2 S 3 S 2 d D O-ring* Series Tube d PN P max l 2 l 2 S 2 S 3 O-ring Weight O.D. (bar) (bar) Shore-Hardness / piece approx OR4.5X.5X OR6.5X.5X OR8X.5X OR0X.5X OR2X2X OR5X2X OR20X2X OR26X2X OR32X2.5X OR38X2.5X 465 I O-ring FP Example OR4.5X.5VITX Series Tube d Dry Technology Dry Technology O.D. EO-2 steel DPR steel EO-2 stainless steel DPR stainless steel E06Z3C E063C E06Z7 E E08Z3C E083C E08Z7 E E0Z3C E03C E0Z7 E E2Z3C E23C E2Z7 E E5Z3C E53C E5Z7 E E8Z3C E83C E8Z7 E E22Z3C E223C E22Z7 E E28Z3C E283C E28Z7 E E35Z3C E353C E35Z7 E E42Z3C E423C E42Z7 E427 Without nut and ring: Example E06OD3C E06OD3C E06OD7 ET06OD7 I 9 Catalogue 400--UK

177 i Ermeto Original WEE-R - djustable ocknut Elbow EO tube end / ale SPP thread with O-ring seal for ports with small or wide spot face l 2 2 S 3 S 2 l 3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ± 0% approx. 90 small 04 G / OR8X.88X RRS/ G / OR8X.88X RRS/ G / OR8X.88X RRS/ G / OR0.77X2.62X RRS/ G / OR0.77X2.62X RRS/4 9 2 G 3/ OR3.94X2.62X RRS3/ G / OR7X3X RRS/ G / OR7X3X RRS/ G 3/ OR23.47X2.95X RRS3/ G OR29.2X3X RRS G / OR37.69X3.53X RRS/ G / OR44.04X3.53X RRS/2 97 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 04 G /8 WEE04ZR3C WEE04R3C 06 G /8 WEE06ZR3C WEE06R3C 06 G /8 WEE06ZR3C WEE06R3C 08 G /4 WEE08ZR3C WEE08R3C 0 G /4 WEE0ZR3C WEE0R3C 2 G 3/8 WEE2ZR3C WEE2R3C 5 G /2 WEE5ZR3C WEE5R3C 8 G /2 WEE8ZR3C WEE8R3C 22 G 3/4 WEE22ZR3C WEE22R3C 28 G WEE28ZR3C WEE28R3C 35 G /4 WEE35ZR3C WEE35R3C 42 G /2 WEE42ZR3C WEE42R3C Without nut and ring: Example WEE06ROD3C WEE06ROD3C *Series with D-rin I 20 Catalogue 400--UK

178 i Ermeto Original TEE-R - djustable ocknut ranch Tee EO tube ends / ale SPP thread with O-ring seal for ports with small or wide spot face l 2 2 S 3 S 2 l 3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ± 0% approx. 90 small 06 G / OR8X.88X RRS/ G / OR0.77X2.62X RRS/ G / OR0.77X2.62X RRS/4 7 2 G 3/ OR3.94X2.62X RRS3/ G / OR7X3X RRS/ G / OR7X3X RRS/ G 3/ OR23.47X2.95X RRS3/ G OR29.2X3X RRS G / OR37.69X3.53X RRS/ G / OR44.04X3.53X RRS/2 428 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 G /8 TEE06ZR3C TEE06R3C 08 G /4 TEE08ZR3C TEE08R3C 0 G /4 TEE0ZR3C TEE0R3C 2 G 3/8 TEE2ZR3C TEE2R3C 5 G /2 TEE5ZR3C TEE5R3C 8 G /2 TEE8ZR3C TEE8R3C 22 G 3/4 TEE22ZR3C TEE22R3C 28 G TEE28ZR3C TEE28R3C 35 G /4 TEE35ZR3C TEE35R3C 42 G /2 TEE42ZR3C TEE42R3C Without nut and ring: Example TEE06ROD3C TEE06ROD3C *Series with D-rin I 2 Catalogue 400--UK

179 Ermeto Original EE-R - djustable ocknut Run Tee EO tube ends / ale SPP thread with O-ring seal for ports with small or wide spot face i l S 2 S 3 l3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ± 0% approx. 90 small 06 G / OR8X.88X RRS/ G / OR0.77X2.62X RRS/ G / OR0.77X2.62X RRS/4 7 2 G 3/ OR3.94X2.62X RRS3/ G / OR7X3X RRS/ G / OR7X3X RRS/ G 3/ OR23.47X2.95X RRS3/ G OR29.2X3X RRS G / OR37.69X3.53X RRS/ G / OR44.04X3.53X RRS/2 428 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 G /8 EE06ZR3C EE06R3C 08 G /4 EE08ZR3C EE08R3C 0 G /4 EE0ZR3C EE0R3C 2 G 3/8 EE2ZR3C EE2R3C 5 G /2 EE5ZR3C EE5R3C 8 G /2 EE8ZR3C EE8R3C 22 G 3/4 EE22ZR3C EE22R3C 28 G EE28ZR3C EE28R3C 35 G /4 EE35ZR3C EE35R3C 42 G /2 EE42ZR3C EE42R3C Without nut and ring: Example EE06ROD3C EE06ROD3C *Series with D-rin I 22 Catalogue 400--UK

180 Ermeto Original VEE-R - djustable ocknut 45 Elbow i EO tube end / ale SPP thread with O-ring seal for ports with small or wide spot face l 2 2 S 2 45 S 3 l3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ± 0% approx. 90 small 06 G / OR8X.88X RRS/ G / OR0.77X2.62X RRS/ G / OR0.77X2.62X RRS/ G 3/ OR3.94X2.62X RRS3/ G / OR7X3X RRS/ G / OR7X3X RRS/ G 3/ OR23.47X2.95X RRS3/ G OR29.2X3X RRS G / OR37.69X3.53X RRS/ G / OR44.04X3.53X RRS/2 795 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 G /8 VEE06ZR3C VEE06R3C 08 G /4 VEE08ZR3C VEE08R3C 0 G /4 VEE0ZR3C VEE0R3C 2 G 3/8 VEE2ZR3C VEE2R3C 5 G /2 VEE5ZR3C VEE5R3C 8 G /2 VEE8ZR3C VEE8R3C 22 G 3/4 VEE22ZR3C VEE22R3C 28 G VEE28ZR3C VEE28R3C 35 G /4 VEE35ZR3C VEE35R3C 42 G /2 VEE42ZR3C VEE42R3C Without nut and ring: Example VEE06ROD3C VEE06ROD3C *Series with D-rin I 23 Catalogue 400--UK

181 Ermeto Original WEE- - djustable ocknut Elbow i EO tube end / ale metric parallel thread with O-ring seal for ports with small or wide spot face l 2 2 S 3 S 2 l 3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / (Nm) ±0% approx. 90 small piece OR8X.88X RRS OR9.3X2.2X RRS OR.3X2.2X RRS OR3.3X2.3X RRS OR5.54X2.62X RRS OR9.2X3X RRS OR23.47X2.95X RRS OR29.2X3X RRS OR37.69X3.53X RRS OR43.69X3X RRS I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 0 WEE06Z3C WEE063C WEE08Z3C WEE083C WEE0Z3C WEE03C WEE2Z3C WEE23C WEE5Z3C WEE53C WEE8Z3C WEE83C WEE22Z27X23C WEE2227X23C WEE28Z3C WEE283C WEE35Z3C WEE353C WEE42Z3C WEE423C Without nut and ring: Example WEE06OD3C WEE06OD3C *Series with D-rin I 24 Catalogue 400--UK

182 Ermeto Original TEE- - djustable ocknut ranch Tee i EO tube ends / ale metric parallel thread with O-ring seal for ports with small or wide spot face l 2 2 S 3 S 2 l 3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ±0% approx. 90 small OR8X.88X RRS OR9.3X2.2X RRS OR.3X2.2X RRS OR3.3X2.2X RRS OR5.54X2.62X RRS OR9.2X3X RRS OR23.47X2.95X RRS OR29.2X3X RRS OR37.69X3.53X RRS OR43.69X3X RRS I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 0 TEE06Z3C TEE063C TEE08Z3C TEE083C TEE0Z3C TEE03C TEE2Z3C TEE23C TEE5Z3C TEE53C TEE8Z3C TEE83C TEE22Z27X23C TEE2227X23C TEE28Z3C TEE283C TEE35Z3C TEE353C TEE42Z3C TEE423C Without nut and ring: Example TEE06OD3C TEE06OD3C *Series with D-rin I 25 Catalogue 400--UK

183 Ermeto Original EE- - djustable ocknut Run Tee EO tube ends / ale metric parallel thread with O-ring seal for ports with small or wide spot face i l S 2 S 3 l3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ±0% approx. 90 small OR8X.88X RRS OR9.3X2.2X RRS OR.3X2.2X RRS OR3.3X2.2X RRS OR5.54X2.62X RRS OR9.2X3X RRS OR23.47X2.95X RRS OR29.2X3X RRS OR37.69X3.53X RRS OR43.69X3X RRS I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 0 EE06Z3C EE063C EE08Z3C EE083C EE0Z3C EE03C EE2Z3C EE23C EE5Z3C EE53C EE8Z3C EE83C EE22Z27X23C EE2227X23C EE28Z3C EE283C EE35Z3C EE353C EE42Z3C EE423C Without nut and ring: Example EE06OD3C EE06OD3C *Series with D-rin I 26 Catalogue 400--UK

184 Ermeto Original VEE- - djustable ocknut 45 Elbow EO tube end / ale metric parallel thread with O-ring seal for ports with small or wide spot face i l 2 2 S 2 45 S 3 l 3 S 4 G D Retaining ring small O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Retaining Weight O.D. (bar) (bar) torque Shore-Hardness ring / piece (Nm) ±0% approx. 90 small OR8X.88X RRS OR9.3X2.2X RRS OR.3X2.2X RRS OR3.3X2.2X RRS OR5.54X2.62X RRS OR9.2X3X RRS OR23.47X2.95X RRS OR29.2X3X RRS OR37.69X3.53X RRS OR43.69X3X RRS48 83 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 0 VEE06Z3C VEE063C VEE08Z3C VEE083C VEE0Z3C VEE03C VEE2Z3C VEE23C VEE5Z3C VEE53C VEE8Z3C VEE83C VEE22Z27X23C VEE2227X23C VEE28Z3C VEE283C VEE35Z3C VEE353C VEE42Z3C VEE423C Without nut and ring: Example VEE06OD3C VEE06OD3C *Series with D-rin I 27 Catalogue 400--UK

185 Ermeto Original WEE-UNF - djustable ocknut Elbow EO tube end / ale UNF/UN parallel thread with O-ring seal i l 2 2 S 3 S 2 l3 S 4 G O-ring D Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Weight O.D. (bar) (bar) torque Shore-Hardness / piece (N) ±0 % approx /6-20 UNF ±2 OR8.92X.83X /6-20 UNF ±2 OR8.92X.83X /6-8 UNF ±3 OR.89X.98X /6-8 UNF ±3 OR.89X.98X 0 2 3/4-6 UNF ±3 OR6.36X2.2X /4-6 UNF ±3 OR6.36X2.2X /8-4 UNF ±4 OR9.8X2.46X /8-4 UNF ±4 OR9.8X2.46X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±8 OR29.74X2.95X /8-2 UN ±6 OR37.47X3X /8-2 UN ±6 OR43.69X3X 928 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 7/6-20 UNF-2 WEE06Z7/6UNF3C WEE067/6UNF3C 08 7/6-20 UNF-2 WEE08Z7/6UNF3C WEE087/6UNF3C 0 9/6-8 UNF-2 WEE0Z9/6UNF3C WEE09/6UNF3C 2 9/6-8 UNF-2 WEE2Z9/6UNF3C WEE29/6UNF3C 2 3/4-6 UNF-2 WEE2Z3/4UNF3C WEE23/4UNF3C 5 3/4-6 UNF-2 WEE5Z3/4UNF3C WEE53/4UNF3C 5 7/8-4 UNF-2 WEE5Z7/8UNF3C WEE57/8UNF3C 8 7/8-4 UNF-2 WEE8Z7/8UNF3C WEE87/8UNF3C 8 /6-2 UN-2 WEE8Z/6UN3C WEE8/6UN3C 22 /6-2 UN-2 WEE22Z/6UN3C WEE22/6UN3C 28 5/6-2 UN-2 WEE28Z5/6UN3C WEE285/6UN3C 35 5/8-2 UN-2 WEE35Z5/8UN3C WEE355/8UN3C 42 7/8-2 UN-2 WEE42Z7/8UN3C WEE427/8UN3C Without nut and ring: Example WEE067/6UNFOD3C WEE067/6UNFOD3C I 28 Catalogue 400--UK

186 Ermeto Original TEE-UNF - djustable ocknut ranch Tee EO tube ends / ale UNF/UN parallel thread with O-ring seal l 2 2 i S 3 S 2 l 3 S 4 G O-ring D Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Weight O.D. (bar) (bar) torque Shore-Hardness / piece (N) ±0 % approx /6-20 UNF ±2 OR8.92X.83X /6-20 UNF ±2 OR8.92X.83X 0 0 9/6-8 UNF ±3 OR.89X.98X /6-8 UNF ±3 OR.89X.98X 9 2 3/4-6 UNF ±3 OR6.36X2.2X /4-6 UNF ±3 OR6.36X2.2X /8-4 UNF ±4 OR9.8X2.46X /8-4 UNF ±4 OR9.8X2.46X 49 8 /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±8 OR29.74X2.95X /8-2 UN ±6 OR37.47X3X /8-2 UN ±6 OR43.69X3X 480 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 7/6-20 UNF-2 TEE06Z7/6UNF3C TEE067/6UNF3C 08 7/6-20 UNF-2 TEE08Z7/6UNF3C TEE087/6UNF3C 0 9/6-8 UNF-2 TEE0Z9/6UNF3C TEE09/6UNF3C 2 9/6-8 UNF-2 TEE2Z9/6UNF3C TEE29/6UNF3C 2 3/4-6 UNF-2 TEE2Z3/4UNF3C TEE23/4UNF3C 5 3/4-6 UNF-2 TEE5Z3/4UNF3C TEE53/4UNF3C 5 7/8-4 UNF-2 TEE5Z7/8UNF3C TEE57/8UNF3C 8 7/8-4 UNF-2 TEE8Z7/8UNF3C TEE87/8UNF3C 8 /6 UN-2 TEE8Z/6UN3C TEE8/6UN3C 22 /6-2 UN-2 TEE22Z/6UN3C TEE22/6UN3C 28 5/6-2 UN-2 TEE28Z5/6UN3C TEE285/6UN3C 35 5/8-2 UN-2 TEE35Z5/8UN3C TEE355/8UN3C 42 7/8-2 UN-2 TEE42Z7/8UN3C TEE427/8UN3C Without nut and ring: Example TEE067/6UNFOD3C TEE067/6UNFOD3C I 29 Catalogue 400--UK

187 Ermeto Original EE-UNF - djustable ocknut Run Tee EO tube ends / ale UNF/UN parallel thread with O-ring seal l 2 2 i 2 S 2 S 3 l3 S 4 G D O-ring Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Weight O.D. (bar) (bar) torque Shore-Hardness / piece (N) ±0 % approx /6-20 UNF ±2 OR8.92X.83X /6-20 UNF ±2 OR8.92X.83X 0 0 9/6-8 UNF ±3 OR.89X.98X /6-8 UNF ±3 OR.89X.98X 9 2 3/4-6 UNF ±3 OR6.36X2.2X /4-6 UNF ±3 OR6.36X2.2X /8-4 UNF ±4 OR9.8X2.46X /8-4 UNF ±4 OR9.8X2.46X 49 8 /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±8 OR29.74X2.95X /8-2 UN ±6 OR37.47X3X /8-2 UN ±6 OR43.69X3X 430 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 7/6-20 UNF-2 EE06Z7/6UNF3C EE067/6UNF3C 08 7/6-20 UNF-2 EE08Z7/6UNF3C EE087/6UNF3C 0 9/6-8 UNF-2 EE0Z9/6UNF3C EE09/6UNF3C 2 9/6-8 UNF-2 EE2Z9/6UNF3C EE29/6UNF3C 2 3/4-6 UNF-2 EE2Z3/4UNF3C EE23/4UNF3C 5 3/4-6 UNF-2 EE5Z3/4UNF3C EE53/4UNF3C 5 7/8-4 UNF-2 EE5Z7/8UNF3C EE57/8UNF3C 8 7/8-4 UNF-2 EE8Z7/8UNF3C EE87/8UNF3C 8 /6-2 UN-2 EE8Z/6UN3C EE8/6UN3C 22 /6-2 UN-2 EE22Z/6UN3C EE22/6UN3C 28 5/6-2 UN-2 EE28Z5/6UN3C EE285/6UN3C 35 5/8-2 UN-2 EE35Z5/8UN3C EE355/8UN3C 42 7/8-2 UN-2 EE42Z7/8UN3C EE427/8UN3C Without nut and ring: Example EE067/6UNFOD3C EE067/6UNFOD3C I 30 Catalogue 400--UK

188 Ermeto Original VEE-UNF - djustable ocknut 45 Elbow EO tube end / ale UNF/UN parallel thread with O-ring seal i l 2 2 S 2 45 S 3 l3 S 4 G O-ring D Series Tube G PN P max 2 I 2 I 3 i D S 2 S 3 S 4 ssembly O-ring Weight O.D. (bar) (bar) torque Shore-Hardness / piece (N) ±0 % approx /6-20 UNF ±2 OR8.92X.83X /6-20 UNF ±2 OR8.92X.83X /6-8 UNF ±3 OR.89X.98X /6-8 UNF ±3 OR.89X.98X 0 2 3/4-6 UNF ±3 OR6.36X2.2X /4-6 UNF ±3 OR6.36X2.2X /8-4 UNF ±4 OR9.8X2.46X /8-4 UNF ±4 OR9.8X2.46X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±7 OR23.47X2.95X /6-2 UN ±8 OR29.74X2.95X /8-2 UN ±6 OR37.47X3X /8-2 UN ±6 OR43.69X3X 85 I Series Tube G Dry Technology O.D. EO-2 steel DPR steel 06 7/6-20 UNF-2 VEE06Z7/6UNF3C VEE067/6UNF3C 08 7/6-20 UNF-2 VEE08Z7/6UNF3C VEE087/6UNF3C 0 9/6-8 UNF-2 VEE0Z9/6UNF3C VEE07/6UNF3C 2 9/6-8 UNF-2 VEE2Z9/6UNF3C VEE29/6UNF3C 2 3/4-6 UNF-2 VEE2Z3/4UNF3C VEE23/4UNF3C 5 3/4-6 UNF-2 VEE5Z3/4UNF3C VEE53/4UNF3C 5 7/8-4 UNF-2 VEE5Z7/8UNF3C VEE57/8UNF3C 8 7/8-4 UNF-2 VEE8Z7/8UNF3C VEE87/8UNF3C 8 /6-2 UN-2 VEE8Z/6UN3C VEE8/6UN3C 22 /6-2 UN-2 VEE22Z/6UN3C VEE22/6UN3C 28 5/6-2 UN-2 VEE28Z5/6UN3C VEE285/6UN3C 35 5/8-2 UN-2 VEE35Z5/8UN3C VEE355/8UN3C 42 7/8-2 UN-2 VEE42Z7/8UN3C VEE427/8UN3C Without nut and ring: Example VEE067/6UNFOD3C VEE067/6UNFOD3C I 3 Catalogue 400--UK

189 Ermeto Original F - EO-2 Functional Nut S 2 d 3 24 d 4 d 3 d 5 h t i Series Tube DN d 3 d 4 d 5 t i S 2 h Weight O.D. Size metric thread / piece I I 32 Catalogue 400--UK

190 Ermeto Original F - EO-2 Functional Nut S 2 d 3 24 d 4 d 3 d 5 h t i Series Tube Dry Technology O.D. Dry Technology Dry Technology Steel NR with Steel/NR Stainless steel/fp stainless steel cutting ring 04 F043C F04SS 06 F063C F06SS 06 F063C F067 F06SS 08 F083C F087 F08SS 0 F03C F07 F0SS 2 F23C F27 F2SS 5 F53C F57 F5SS 8 F83C F87 F8SS 22 F223C F227 F22SS 28 F283C F287 F28SS 35 F353C F357 F35SS 42 F423C F427 F42SS I I 33 Catalogue 400--UK

191 Ermeto Original Nut - DPR Progressive ring - D Cutting ring h S 2 d 3 i Progressive ring: DPR d 3 24 d 4 d 3 d 3 d 5 Nut: t Cutting ring: D Series Tube DN d 3 d 4 d 5 t i S 2 h Weight O.D. Size metric / piece thread DPR (D) I I 34 Catalogue 400--UK

192 Nut - DPR Progressive ring - D Cutting ring Ermeto Original h S 2 d 3 i Progressive ring: DPR d 3 d 3 24 d 4 d 3 d 5 Nut: t Cutting ring: D Series Tube O.D. Steel Stainless steel brass CX 047X 04SX CX 067X 06SX CX 087X 08SX 0 03CX 07X 0SX 2 23CX 27X 2SX CX 06EODURX 06SX CX 08EODURX 08SX 0 03CX 0EODURX 0SX 2 23CX 2EODURX 2SX 5 53CX 5EODURX 5SX 8 83CX 8EODURX 8SX CX 22EODURX 22SX CX 28EODURX 28SX CX 35EODURX 35SX CX 42EODURX 42SX DPR (D) Steel Stainless steel brass D04X D047X D04SX D06X D067X D06SX D08X D087X D08SX D0X D07X D0SX D2X D27X D2SX DPR06X DPR067X D06SX DPR08X DPR087X D08SX DPR0X DPR07X D0SX DPR2X DPR27X D2SX DPR5X DPR57X D5SX DPR8X DPR87X D8SX DPR22X DPR227X D22SX DPR28X DPR287X D28SX DPR35X DPR357X D35SX DPR42X DPR427X D42SX I I 35 Catalogue 400--UK

193 Ermeto Original G - ulkhead locknut SW h Series Tube SW h Weight O.D. metric thread / piece Series Tube O.D. Steel Stainless steel rass 06 G063CX G067X G06SX 08 G083CX G087X G08SX 0 G03CX G07X G0SX 2 G23CX G27X G2SX 5 G53CX G57X G5SX 8 G83CX G87X G8SX 22 G223CX G227X G22SX 28 G283CX G287X G28SX 35 G353CX G357X G35SX 42 G423CX G427X G42SX I I 36 Catalogue 400--UK

194 Ermeto Original VK - lanking plug for cones Tube O.D. O-Ring Series Tube PN P max O-ring Weight O.D. (bar) (bar) Shore-Hardness / piece approx OR4.5X.5X OR6.5X.5X OR8X.5X OR0X.5X OR2X2X OR5X2X OR20X2X OR26X2X OR32X2.5X OR38X2.5X 343 O-ring FP: Example OR4.5X.5VITX I Series Tube Dry Technology Dry Technology O.D. Steel/NR Stainless steel/fp rass/nr 06 VK063C VK067 VK06S 08 VK083C VK087 VK08S 0 VK03C VK07 VK0S 2 VK23C VK27 VK2S 5 VK53C VK57 VK5S 8 VK83C VK87 VK8S 22 VK223C VK227 VK22S 28 VK283C VK287 VK28S 35 VK353C VK357 VK35S 42 VK423C VK427 VK42S I 37 Catalogue 400--UK

195 Ermeto Original VSTI R/-ED - lanking plug for ports SPP or etric parallel thread with Eolastic sealing ED i S 6 D G Eolastic - sealing ale metric ale stud PN P max D i S 6 Weight Dry Technology Steel Dry Technology Stainless steel parallel SP (bar) (bar) / piece etric parallel SPP etric parallel SPP thread G thread G 0 G / VSTI0XED3C VSTI/8ED3C VSTI0XED7 VSTI/8ED VSTI2X.5ED3C VSTI2X.5ED7 4.5 G / VSTI4X.5ED3C VSTI/4ED3C VSTI4X.5ED7 VSTI/4ED7 6.5 G 3/ VSTI6X.5ED3C VSTI3/8ED3C VSTI6X.5ED7 VSTI3/8ED VSTI8X.5ED3C VSTI8X.5ED VSTI20X.5ED3C VSTI20X.5ED G / VSTI22X.5ED3C VSTI/2ED3C VSTI22X.5ED7 VSTI/2ED VSTI26X.5ED3C VSTI26X.5ED G 3/ VSTI27X2ED3C VSTI3/4ED3C VSTI27X2ED7 VSTI3/4ED G VSTI33X2ED3C VSTIED3C VSTI33X2ED7 VSTIED G / VSTI42X2ED3C VSTI/4ED3C VSTI42X2ED7 VSTI/4ED G / VSTI48X2ED3C VSTI/2ED3C VSTI48X2ED7 VSTI/2ED7 I I 38 Catalogue 400--UK

196 Ermeto Original E - Tube insert for plastic tubing d D d Tube ID D d d Weight O.D. / piece rass E04/02X E04/2.5X E0506/03X E0506/03X E0506/04X E0506/04X E08/04X E06/05X E08/05X E080/06X E080/06X E0/08X E2/08X E2/09X E25/0X E5/2X E56/2.5X E56/2.5X E8/4X E820/6X E820/6X E22/8X I I 39 Catalogue 400--UK

197 Ermeto Original SensoControl The Serviceman for fluid systems Hand-held measuring device to measure pressure, temperature, flow and rotational speed Easy operation Rugged design Compact dimensions arge display Units of measurement displayed Differential value measurement IN/X emory Hold function 2 inputs with sensor recognition ow power consumption Data output for printer and PC External power supply I The SERVICEN SC-50 from Parker is a modern measuring system and real alternative to conventional mechanical pressure measurement in fluid systems. The device can be used wherever fluid control and components are in use. The SC-50 is very tough and insensitive to dirt so that it can be used in extreme conditions. It can be carried by hand or used as a desktop unit with an integrated stand. Operation is very easy. Everything is controlled by 8 buttons. 2 sensors inputs are provided, thus enables differential measurements. dynamic maximum and minimum value memory and a display hold function have also been implemented. The Serviceman identifies the type of connected sensors and its proper units (bar; l/min; PP; C). Therefore wrong measurements and time consuming adjustments are thus avoided. printer can also be used to document the most important fluid parameters. Following a pre-set transmission interval of between and 00 sec., the device automatically documents the maximum, minimum and current values for the system. I 40 The memory is deleted after printin This permits a precise determination of the extreme values per machine cycle. The device can be connected to any PC with an auxiliary PC adapter. Thus, the drafting of status reports to verify data (ISO 9000) poses no problems. The Serviceman SC-50 will be of interest to all maintenance engineers working with mobile hydraulic systems, in the construction, machinery and equipment sector, environmental engineering, ship-building and offshore. The Serviceman has been developed to give an excellent range of functions and benefits, at a modest price. Catalogue 400--UK

198 Ermeto Original Technical Data Inputs 2 inputs with sensor-recognition (p, T, Q, n) Resolution 2 it = steps Scanning rate = < 2 ms Display CD text display (4-digit) Character height: 3 mm ccuracy: < 0.3% ± 2 digits Display of units: bar, PSI, /min., USGP, C, F, U/min., RP, % Functions Diffential value measurement IN/X memory Hold function utoprint function (SC ) attery level display O T uto power off after 5 min. Data-Output SC Infrared interface (RS232C) to thermoprinter SCPR-00 or PC (only in combination with SCD-50) mbient conditions Temperature range: 0 50 C Storage temperature: C Rel. humidity: <85 % Protection level: IP54 (EN 60529) EC compatibility pursuant to: Interference emission DIN/EN 5008 Part (VDE 0839 Part 8-) Interference emission DIN/EN 5008 Part (VDE 0839 Part 8-) Power supply SC V battery (IEC 6F 22) pprox. 5 h operation with one sensor SC NC storage battery, 9V pprox. 5 h operation with one sensor attery charge circuit External power supply with SCSN-350 General Housing material Plastic housing of S Protective covering of rubber and carrying straps Dimensions /W/H mm Weight pprox. 340 Functional description SC-50 4-digit CD to display units, input status and battery status RESET to delete IN/X Readings On/Off switch I aximum value display RESET must be pressed before start of measurement Channel selection input /2 Differential value Input minus Input 2 inimum value display RESET must be pressed before the start of measurements Printout of actual/max/min values in numerical form Hold function for display values 2 sensor inputs Socket for external power supply (SC ) Data output (SC ) Data transmission to printer SCPR-00 or PC with SCD-50 adaptor. I 4 Catalogue 400--UK

199 Ermeto Original Fluid System Display SCP Display SCP Display SCP T SCT SCP-XXX SC-G3/20S/T SC-/2-E-3 Diagnostic-dapter (6x2) SCK SCK Serviceman Q I Q For further details, please look at bulletin 405. Flow turbine SCFT-XXX-0-02 PC-Software SC SN 350 SCK SCK PC-dapter PC-Connecting Cable SC PR 00 SC SN 00 I 42 Catalogue 400--UK

200 Ermeto Original Order code Description Part no Handmeter SC-50 to measure p, T, Q, n SC also with data output an external SC power supply Pressure sensor SCP with fixed cable connection for direct connection to the SC-50 SCP easuring range - 5 bar bar bar 000 Flow sensor SCQ further information on data sheet 4069 Flow turbine SCFT complete with measuring points for pressure and temperature, signal converter with voltage output SCFT For details please see data sheet 4068 easuring range.0 5 l/min l/min l/min l/min 600 Temperature measurement measuring range C SCT I Rotational speed recording measuring range rpm SCRP-20 Connecting cable, 2 m connection sensor/handmeter SCK ccessories for SC-50 easuring case for handmeter, pressure sensors, adapters SC-500 charger and battery also for printer and flow sensors SCC-550 Printer SCPR thermoprinter for connection to SC SCPR Printer cable, m optical transmission SCK PC adapter to transfer data to a PC SCD-50 Charger to charge NiCD storage battery SC-8 SC-800 NiCD storage battery 9V/0mh (IEC 6F 22) SC-8 ains adapter SCSN power supply for SC SCSN-350 power supply for SC, SCPR, SCD-50 SCSN-345 Car cable, 5 m connection between car socket SC SCK / Calibration certificate for SC-50 according to DIN ISO 900/EN I 43 Catalogue 400--UK

201 rass adaptors rass adaptors for heavy duty applications Catalogue 4360-UK

202 rass adaptors J J 2 Catalogue 4360-UK

203 rass adaptors Index Pipe nipples equal SPT FF33 - p. J 5 equal NPTF FF - p. J 5 equal NPTF 26P - p. J 5 unequal SPT FF33 - p. J 5 equal SPP FF44 - p. J 5 Reducers reducing connector female-male SPP-SPT FG43 - p. J 6 reducing connector female-male NPTF FG - p. J 6 reducing connector female-male NPTF 222P - p. J 6 pipe thread reducer male-female SPT-SPP PTR34 - p. J 6 pipe thread reducer male-female NPTF PTR - p. J 7 pipe thread reducer male-female NPTF 209P - p. J 7 Pipe connectors equal SPP GG44 - p. J 8 equal NPTF GG - p. J 8 equal NPTF 207P - p. J 8 unequal SPP GG44 - p. J 8 ulkhead unions female - SPP WGG44 - p. J 9 female - NPTF 207CH - p. J 9 90 elbows male-female SPT-SPP CD43 - p. J 9 equal female SPP DD44 - p. J 9 Tees J equal female SPP O444 - p. J 0 male branch tee SPP-SPP-SPT S443 - p. J 0 male run tee SPP-SPT-SPP RO434 - p. J 0 Cross equal female SPP KOO4 - p. J 0 Plugs hex head SPT HP3 - p. J hex head NPTF HP - p. J hex head NPTF 28P - p. J hollow hex SPT HHP3 - p. J hollow hex NPTF HHP - p. J 2 hollow hex NPTF 29P - p. J 2 Conversion adaptors male NPT - female SPP FHG4 - p. J 2 J 3 Catalogue 4360-UK

204 rass adaptors To simplify the installation of pneumatic systems, Parker supplies a comprehensive range of adaptors for SPP, SPT and NPT pipe threads. The range includes pipe nipples, pipe connectors, reducers, bulkhead female unions, elbows, tees, crosses and hex head plugs. Technical features aterial Working temperature Working pressure rass From - 60 C to + 90 C 60 bar except where indicated dvantages rass forgings J Parker brass adaptors are produced from hot forgings to meet exacting tolerances. Packaging Parker brass adaptors are packaged in biodegradable plastic bags preventing thread damage and ensuring a quality adaptor. The hot forging process increases the density of the material, refines the grain structure and improves material strength. J 4 Catalogue 4360-UK

205 rass adaptors FF33 - Pipe nipple - SPT P P Part number C P Weight C /8 /8FF /4 /4FF /8 3/8FF /2 /2FF /4 3/4FF FF FF - Pipe nipple - NPTF - Heavy series P P Part number C* P Weight in mm Working pressure (bar) C 26P - Pipe nipple - NPTF /8 /8FF 7/ /4 /4FF 5/ /8 3/8FF 3/ /2 /2FF 7/ * Inch dimensions P P Part number C* P Weight in mm FF33 - Unequal pipe nipple - SPT C /8 26P-2 7/ /4 26P-4 9/ /8 26P-6 / /2 26P-8 7/ * Inch dimensions J 2 Part number C P P2 Weight P P2 2 /8 /4 /8x/4FF /8 3/8 /8x3/8FF /8 /2 /8x/2FF /4 3/8 /4x3/8FF /4 /2 /4x/2FF C 3/8 /2 3/8x/2FF /8 3/4 3/8x3/4FF /2 3/4 /2x3/4FF /4 3/4xFF FF44 - Pipe nipple - SPP J T J Part number C J T Weight /8 /8FF /4 /4FF /8 3/8FF /2 /2FF C These parts are supplied with two copper seals. J 5 Catalogue 4360-UK

206 rass adaptors FG43 - Reducing connector female-male - SPP-SPT Part number C J P Weight J /8 /4 /4x/8FG /8 3/8 3/8x/8FG /4 3/8 3/8x/4FG /8 /2 /2x/8FG /4 /2 /2x/4FG C P 3/8 /2 /2x3/8FG /2 3/4 3/4x/2FG /4 x3/4fg FG - Reducing connector female-male - NPTF - Heavy series P 2 Part number C* P P2 Weight in mm Working pressure (bar) 2 /4 /8 /4x/8FG 3/4 9, /8 /4 3/8x/4FG 7/8 22, /2 3/8 /2x3/8FG,/8 28, * Inch dimensions C P2 222P - Reducing connector female-male - NPTF P 2 Part number C* P P2 Weight in mm 2 /4 /8 222P-4-2 3/ /8 /4 222P-6-4 7/ /2 3/8 222P-8-6./ J * Inch dimensions C P2 PTR34 - Pipe thread reducer male-female - SPT-SPP Part number C J P Weight J /4 /8 /4x/8PTR /8 /8 3/8x/8PTR /8 /4 3/8x/4PTR /2 /8 /2x/8PTR /2 /4 /2x/4PTR P C /2 3/8 /2x3/8PTR /4 3/8 3/4x3/8PTR /4 /2 3/4x/2PTR /2 x/2ptr /4 x3/4ptr For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 6 Catalogue 4360-UK

207 rass adaptors PTR - Pipe thread reducer male-female - NPTF - Heavy series P P2 C 2 2 Part number C* P P2 Working Weight pressure in mm (bar) /4 /8 /4x/8PTR 5/ /8 /8 3/8x/8PTR 3/ /8 /4 3/8x/4PTR 3/ /2 /4 /2x/4PTR 7/ /2 3/8 /2x3/8PTR 7/ /4 3/8 3/4x3/8PTR./ /4 /2 3/4x/2PTR./ * Inch dimensions 209P - Pipe thread reducer male-female - NPTF 2 Part number C* P P2 Weight in mm P P2 C 2 /4 /8 209P-4-2 9/ /8 /8 209P-6-2 / /8 /4 209P-6-4 / /2 /4 209P-8-4 7/ /2 3/8 209P-8-6 7/ /4 3/8 209P-2-6./ /4 /2 209P-2-8./ * Inch dimensions J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 7 Catalogue 4360-UK

208 rass adaptors GG44 - Pipe connector - SPP J J Part number C J Weight C /8 /8GG /4 /4GG /8 3/8GG /2 /2GG /4 3/4GG GG GG - Pipe connector - NPTF - Heavy series P P Part number C* P Weight in mm Working pressure (bar) C /8 /8GG 5/ /4 /4GG 3/ /8 3/8GG 7/ /2 /2GG./ * Inch dimensions 207P - Pipe connector - NPTF C P P Part number C* P Weight in mm /8 207P-2 9/ /4 207P-4 3/ /8 207P-6 7/ /2 207P-8./ * Inch dimensions J GG44 - Unequal pipe connector - SPP J J2 2 Part number C J J2 Weight C 2 /8 /4 /8x/4GG /8 3/8 /8x3/8GG /8 /2 /8x/2GG /4 3/8 /4x3/8GG /4 /2 /4x/2GG /8 /2 3/8x/2GG For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 8 Catalogue 4360-UK

209 rass adaptors WGG44 - ulkhead female union - SPP T W T Part number C C4 T T W Weight C C4 /8 /8WGG44 6x /4 /4WGG44 20x /8 3/8WGG44 23x /2 /2WGG44 27x /4 3/4WGG44 34x WGG44 45x CH - ulkhead female union - NPTF T W P T P Part number C C4 P T T W Weight C C4 /8 207CH-2 5/8-8 7/8* 5/6* /4 207CH-4 3/4-6 *./8* /8 207CH-6-4./8*./4* /2 207CH-8./8-4./4*.3/8* /4 207CH-34 34x CH-45 45x * Inch dimensions CD43-90 elbow male-female - SPT-SPP C J Y N Part number C J N P Y Weight /8 /8 /8CD /4 /4 /4CD /8 3/8 3/8CD /2 /2 /2CD J P DD44-90 female pipe elbow - SPP J C Part number C J Weight /8 /8DD /4 /4DD /8 3/8DD /2 /2DD For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 9 Catalogue 4360-UK

210 rass adaptors O444 - Female pipe tee - SPP J C Part number C J Weight /8 /8O /4 /4O /8 3/8O /2 /2O /4 3/4O O S443 - ranch tee female-female-male - SPP-SPP-SPT J C Part number C J N P Weight /8 /8 /8S /4 /4 /4S /8 3/8 3/8S /2 /2 /2S P N RO434 - Run tee female-male-female - SPP-SPT-SPP C N P Part number C J N P Weight /8 /8 /8RO /4 /4 /4RO /8 3/8 3/8RO /2 /2 /2RO J J KOO4 - Female pipe cross - SPP Part number C J Weight C /8 /8KOO /4 /4KOO /8 3/8KOO /2 /2KOO J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 0 Catalogue 4360-UK

211 rass adaptors HP3 - Hex head plug - SPT Part number C P Weight P C /8 /8HP /4 /4HP /8 3/8HP /2 /2HP /4 3/4HP HP HP - Hex head plug - NPTF - Heavy series Part number C* P Weight in mm Working pressure (bar) P C /8 /8HP 7/ /4 /4HP 9/ /8 3/8HP / /2 /2HP 7/ * Inch dimensions 28P - Hex head plug - NPTF Part number C* P Weight in mm P C /8 28P-2 7/ /4 28P-4 9/ /8 28P-6 / /2 28P-8 7/ * Inch dimensions J HHP3 - Hollow hex head plug - SPT C5 Part number C5 Weight /8 /8HHP /4 /4HHP /8 3/8HHP3 8 0 /2 /2HHP For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J Catalogue 4360-UK

212 rass adaptors HHP - Hollow hex head plug - NPTF - Heavy series C5 Part number C5* Weight in mm Working pressure /8 /8HHP 3/ /4 /4HHP / (bar) * Inch dimensions 29P - Hollow hex head plug - NPTF C5 Part number C5* Weight in mm /8 29P-2 3/ /4 29P-4 / * Inch dimensions FHG4 - Conversion adaptor - ale NPT to female SPP J Part number C J P Weight /8 /8 /8FHG /4 /4 /4FHG /8 3/8 3/8FHG /2 /2 /2FHG C P J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. J 2 Catalogue 4360-UK

213 rass adaptors for automotive industry Catalogue UK

214 rass adaptors for automotive industry Index Straight connectors male - SPP F4UCO - p. K 5 90 elbow connectors large radius large radius male-female - SPP male - SPP male - SPP C4UD4 - p. K 5 C4UCO - p. K 5 C4UCO - p. K 6 Tee & Y connectors K male tee SPP male - SPP male - SPP S4UCO - p. K 6 YGX/X-82 - p. K 6 YGX/XCO - p. K 7 Conversion adaptors equal pipe nipple male-female - SPP male - SPP F4UG4 - p. K 7 F4UF4U - p. K 7 K 2 Catalogue UK

215 rass adaptors for automotive industry Index daptors straight - metric 45 elbow - metric 90 elbow - metric SP taper SP taper SP taper E- p. K 8 EV - p. K 8 EW - p. K 8 daptors (Ford standard UWR ) male nipple male nipple male nipple 90 elbow 45 elbow 4-4F3 - p. K 9 4-4C3 p. K 9 4-4V3 - p. K 9 K male swivel nut male swivel nut male swivel nut 90 elbow 45 elbow 4-4F63 - p. K 0 4-4C63 p. K 0 4-4V63 - p. K 0 K 3 Catalogue UK

216 rass adaptors for automotive industry To improve its brass adaptors range, Parker developed a new range of adaptors particularly designed for the automotive industry. These adaptors are existing in various configuration and are equipped with SPP pipe threads. They are used to convey water or welding heads cooling system and also on compressed air circuits used to pilot automated clamping system. Technical features aterial Working temperature Working pressure rass From - 60 C to + 90 C 60 bar except where indicated dvantages rass forgings K Parker brass adaptors are produced from hot forgings to meet exacting tolerances. Packaging Parker brass adaptors are packaged in biodegradable plastic bags preventing thread damage and ensuring a quality adaptor. The hot forging process increases the density of the material, refines the grain structure and improves material strength. K 4 Catalogue UK

217 F4UCO - ale connector - SPP rass adaptors for automotive industry Part number C D J Weight D C /8 0x F4UCO6-/ /4 0x F4UCO6-/ /8 2x F4UCO8-/ /4 2x F4UCO8-/ /8 6x.5 F4UCO0-/ J /4 6x.5 F4UCO0-/ /8 6x.5 F4UCO0-3/ /8 20x.5 F4UCO4-3/ /8 22x.5 F4UCO6-3/ /2 22x.5 F4UCO6-/ /2 24x.5 F4UCO8-/ C4UD4 - ale-female 90 elbow - arge radius - SPP C E Part number C C4 D E N J Weight 3/8 3/8 C4UD43/ /2 3/8 C4UD4/2-3/ N C4 J D C4UCO - ale 90 elbow - arge radius - SPP Part number C C4 D E N J Weight K C D /4 6x.5 C4UCO0-/ /8 6x.5 C4UCO0-3/ /8 20x.5 C4UCO4-3/ N C4 J D For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 5 Catalogue UK

218 rass adaptors for automotive industry C4UCO - ale 90 elbow - SPP Part number C C4 D D J N Weight N C4 C D /8 2x C4UCO8-/ /4 2x C4UCO8-/ /4 6x.5 C4UCO0-/ /8 6x.5 C4UCO0-3/ J D S4UCO - ale branch tee - SPP C Part number C C4 D D N J Weight /4 6x.5 S4UCO0-/ D N C4 J D YGX/X-82 - ale Y connector - SPP J K C C4 C D D D D Y N Part number C C C4 D D J N Y Weight 3/8 20x.5 YG3/ /2 20x.5 YG/ /8 6x.5 YG3/ For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 6 Catalogue UK

219 YGX/XCO - ale Y connector - SPP rass adaptors for automotive industry C Part number C C4 D D J Weight C4 D 3/8 6x.5 YG3/8CO0COP /8 20x.5 YG3/8CO4COP /2 20x.5 YG/2CO4COP D J D F4UG4 - ale-female enlarging adaptor - SPP Part number C D J Weight C D J /8 /8 /8F4UG /4 /4 /4F4UG /4 /4 /4F4UG /4 /4 /4F4UG /8 3/8 3/8F4UG /8 3/8 3/8F4UG /8 3/8 3/8F4UG F4UF4U - ale equal pipe nipple - SPP Part number C C4 D J J Weight K D C C4 /8 /8 /8F4UF4U /4 /4 /4F4UF4U /8 3/8 3/8F4UFU /2 /2 /2F4UF4U /4 3/4 3/4F4UF4U J J For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 7 Catalogue UK

220 rass adaptors for automotive industry E- Straight adaptor - metric 60 cone - SPT Thread DN Part number G G2 W Weight metric SPT mm mm G2 W G 6 EG6-/8 2x / EG6-/4 2x / EG2x5-/8 2x.5 / EG2x5-/4 2x.5 / EG8-/4 4x.5 / EG8-3/8 4x.5 3/ EG0-/4 6x.5 / EG0-/2 6x.5 / EG0-3/8 6x.5 3/ EG5-/2 22x.5 / EG5-3/8 22x.5 3/ EG8-3/4 26x.5 3/ EV - 45 elbow adaptor - metric 60 cone - SPT Thread G DN Part number G G2 Weight metric SPT mm 6 EV6-/8 2x / EV6-/4 2x / EV8-/4 4x.5 / EV8-3/8 4x.5 3/ EV0-/4 6x.5 / G2 0 EV0-3/8 6x.5 3/ EV5-/2 22x.5 /2 30 EW - 90 elbow adaptor - metric 60 cone - SPT K Thread G DN Part number G G2 Weight metric SPT mm 6 EW6-/8 2x / EW6-/4 2x / EW2x5-/4 2x.5 / EW8-/4 4x.5 / EW8-3/8 4x.5 3/ G2 0 EW0-/4 6x.5 / EW0-3/8 6x.5 3/ EW5-/2 22x.5 / For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 8 Catalogue UK

221 rass adaptors for automotive industry 4-4F3 - ale nipple straight fitting (Ford standard UW ) Part number C P Weight C /4 4x.5 4-4F3X Designed to be used in conjunction with Parker Push-ok hose fittings H and H for both welding robots and portable guns on water cooling and compressed air circuits. See the Push-ok Hose and Fitting section (P). P 4-4C3 - ale nipple 90 elbow (Ford standard UW ) Part number C N P Weight C /4 4x.5 4-4C3X8H Designed to be used in conjunction with Parker Push-ok hose fittings H and H for both welding robots and portable guns on water cooling and compressed air circuits. See the Push-ok Hose and Fitting section (P). N P 4-4V3 - ale nipple 45 elbow (Ford standard UW ) Part number C N P Weight K 37 C /4 4x.5 4-4V3X8H Designed to be used in conjunction with Parker Push-ok hose fittings H and H for both welding robots and portable guns on water cooling and compressed air circuits. See the Push-ok Hose and Fitting section (P). P N For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 9 Catalogue UK

222 rass adaptors for automotive industry 4-4F63 - ale swivel nut straight fitting (Ford standard UW ) Part number C C O P Weight C C /4 4x.5 4-4F63X Designed to be used in conjunction with Parker Push-ok hose fittings H and H for both welding robots and portable guns on water cooling and compressed air circuits. See the Push-ok Hose and Fitting section (P). O P 4-4C63 - ale swivel nut 90 elbow (Ford standard UW ) Part number C C N O P Weight C C /4 4x.5 4-4C63X8H Designed to be used in conjunction with Parker Push-ok hose fittings H and H for both welding robots and portable guns on water cooling and compressed air circuits. See the Push-ok Hose and Fitting section (P). O P N 4-4V63 - ale swivel nut 45 elbow (Ford standard UW ) Part number C C N O P Weight K C C N P /4 4X.5 4-4V63X8H O For product availability please consult our price list 0093-UK Dimensions shown may be changed at any time without prior notice. K 0 Catalogue UK

223 Pneumatic adaptors Nickel plated brass adaptors for pneumatic applications Catalogue UK

224 Pneumatic adaptors Index Pipe nipples equal unequal equal unequal equal SPT SPT SPP SPP metric FF33 - p. 6 FF33 - p. 6 FF44 - p. 6 FF44 - p. 6 FF88 - p. 7 unequal male-male metric / SPP SPT FF84 - p. 7 FF633 - p. 7 Reducers female-male female-male female-male female-male extend. male-female SPP-SPT SPP / metric SPP SPP SPT-SPP FG43 - p. 7 FG48 - p. 8 FG44 - p. 8 FF4G4 - p. 8 PTR34 - p. 8 male-female male-female male-female SPP / metric SPP SPP PTR48 - p. 9 PTR44 - p. 9 PTR44H - p. 9 Pipe connectors and bulkhead unions equal equal unequal unequal female metric SPP metric SPP SPP GG88 - p. 9 GG44 - p. 0 GG84 - p. 0 GG44 - p. 0 WG44 - p elbows male female female-male female SPT SPP SPP-SPT SPP CR33 - p. DD44 - p. CD43 - p. DD44KT - p. 2 Catalogue UK

225 Pneumatic adaptors Index Tees and Cross equal female equal male female-male-male female-female-male female-male-female SPP SPT SPP-SPT-SPT SPP-SPP-SPT SPP-SPT-SPP O444 - p. 2 RRS333 - p. 2 RS433 - p. 2 S443 - p. 2 RO434 - p. 3 male-male-female equal female fem-fem-male-fem. equal male SPT-SPT-SPP SPP SPP-SPP-SPT-SPP SPT RRO334 - p. 3 KOO4 - p. 3 KRO4434- p. 3 KRRS3- p. 4 Y connectors female female-female-male SPP SPP-SPP-SPT Y444 -p. 4 YS443 - p. 4 Plugs and Caps male male male male female SPP metric SPP SPT SPP P4UN - p. 4 P80N - p. 5 P40N - p. 5 HHP3 - p. 5 FN4 - p. 5 Hose barb fittings female male male SPP SPT SPP FGH - p. 6 F3H - p. 6 F4H - p. 7 luminium manifolds and washers manifold manifold manifold 2 SPP SPP SPP aluminium washer nylon washer NIF - p. 7 NI - p. 7 NI2 - p. 8 RRD - p. 8 RRP - p. 8 3 Catalogue UK

226 Pneumatic adaptors Principle To simplify the installation of pneumatic systems, Parker supplies a comprehensive range of adaptors with SPT, SPP and metric threads. The range includes pipe nipples, reducers, bulkhead unions, elbows, tees, crosses and plugs. The technical features of the pneumatic adaptors allow their use in several applications as well as with other compatible products within the Parker range. Technical features aterial Threads* Woking pressure Working temperature Nickel plated SPP from 0.0 from - 60 C brass SPT etric to 5 bar to + 90 C * These adaptors have been designed for low pressure applications with the principal target to reduce space and weight. They are compatible with most of current threads used on this type of application. If a specific standard is required, please consult us. dvantages rass forgings Parker pneumatic adaptors are produced from hot forgings to meet exacting tolerences. The hot forging process increases the density of the material, refines the grain structure and improves material strength. 4 Catalogue UK

227 Pneumatic adaptors dvantages rass nickel plated body rass is a raw material providing : - robustness, - excellent shock resistance, - good temperature capability, - nickel plating gives improved corrosion resistance and a bright appearance which does not deteriorate. Excellent features Pneumatic adaptors have been designed to guarantee : - an efficient and economic solution for all applications, - compact dimensions where space is at a premium, - a significant weight savin Packaging Parker pneumatic adaptors are packaged in biodegradable plastic bags preventing thread damage and ensuring a quality adaptor. 5 Catalogue UK

228 Pneumatic adaptors FF33 - Equal pipe nipple - SPT Part number C P Weight P C P /8 /8FF /4 /4FF /8 3/8FF /2 /2FF /4 3/4FF FF FF33 - Unequal pipe nipple - SPT 2 Part number C P P2 Weight 2 C P2 P /8 /4 /8x/4FF /8 3/8 /8x3/8FF /8 /2 /8x/2FF /4 3/8 /4x3/8FF /4 /2 /4x/2FF /8 /2 3/8x/2FF /2 3/4 /2x3/4FF /4 3/4xFF FF44 - Equal pipe nipple - SPP J C J Part number C J Weight /8 /8FF /4 /4FF /8 3/8FF /2 /2FF These parts require two RRD or RRP washers to order separately. FF44 - Unequal pipe nipple - SPP 2 J2 C J 2 Part number C J J2 Weight /8 /4 /8x/4FF /8 3/8 /8x3/8FF /4 3/8 /4x3/8FF /4 /2 /4x/2FF /8 /2 3/8x/2FF /2 3/4 /2x3/4FF These parts require two RRD or RRP washers to order separately. For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 6 Catalogue UK

229 Pneumatic adaptors FF88 - Equal pipe nipple - etric J C J Part number C J Weight 5 5FF This part requires two RRD or RRP washers to order separately. FF84 - Unequal pipe nipple - etric / SPP J2 C J 2 Part number C J J2 Weight 5 /8 5x/8FF This part requires two RRD or RRP washers to order separately. 2 FF633 - Swivel pipe nipple male-male - SPT Part number C C P Weight P C C P /8 /8FF /4 /4FF /8 3/8FF /2 /2FF /4 3/4FF FF Fittings not nickel plated. FG43 - Reducing connector female-male - SPP-SPT Part number C P Weight C P /8 /8 /8FG /8 3/8 3/8x/8FG /8 /4 /4x/8FG /4 /4 /4FG /8 /4 3/8x/4FG /2 /4 /2x/4FG /8 3/8 3/8FG /2 3/8 /2x3/8FG /2 /2 /2FG /4 /2 3/4x/2FG For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 7 Catalogue UK

230 Pneumatic adaptors FG48 - Reducing connector female-male - SPP / etric 2 Part number C J Weight C J 2 /8 5 /8x5FG This part requires one RRD or RRP washer to order separately. FG44 - Reducing connector female-male - SPP 2 Part number C J Weight C J /8 /8 /8FG /8 /8 3/8x/8FG /4 /8 /4x/8FG /4 /4 /4FG /8 /4 3/8x/4FG /8 3/8 3/8FG /2 /4 /2x/4FG /2 3/8 /2x3/8FG /2 /2 /2FG These parts require one RRD or RRP washer to order separately. FF4G4 - Extended connector female-male - SPP 2 Part number C J Weight 2 C J /8 /8 /8FF4G /8 /8 /8FF4G /4 /4 /4FF4G /4 /4 /4FF4G These parts require one RRD or RRP washer to order separately. PTR34 - Pipe thread reducer male-female - SPT-SPP Part number C P Weight C P /4 /8 /4x/8PTR /8 /8 3/8x/8PTR /2 /8 /2x/8PTR /8 /4 3/8x/4PTR /2 /4 /2x/4PTR /2 3/8 /2x3/8PTR /4 3/8 3/4x3/8PTR /4 /2 3/4x/2PTR /2 x/2ptr /4 x3/4ptr /4 /2./4x/2PTR Catalogue UK

231 Pneumatic adaptors PTR48 - Pipe thread reducer male-female - SPP / etric C J 2 Part number C J Weight /8 5 /8x5PTR This part requires one RRD or RRP washer to order separately. 2 PTR44 - Pipe thread reducer male-female - SPP 2 C J 2 Part number C J Weight /4 /8 /4x/8PTR /8 /8 3/8x/8PTR /2 /8 /2x/8PTR /8 /4 3/8x/4PTR /2 /4 /2x/4PTR /2 3/8 /2x3/8PTR /4 3/8 3/4x3/8PTR /4 /2 3/4x/2PTR These parts require one RRD or RRP washer to order separately. PTR44H - Pipe thread reducer male-female - SPP 2 Part number Weight 2 /8 /4 /4x/8PTR44H 8 3 /4 3/8 3/8x/4PTR44H 9 5 3/8 /2 /2x3/8PTR44H 0 7 /2 3/4 3/4x/2PTR44H 4 9 3/4 x3/4ptr44h 20 4 Fittings not nickel plated. GG88 - Equal pipe connector - etric C Part number C Weight 5 5GG For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 9 Catalogue UK

232 Pneumatic adaptors GG84 - Unequal pipe connector - etric C 2 Part number C Weight 5 /8 5x/8GG GG44 - Equal pipe connector - SPP C Part number C Weight /8 /8GG /4 /4GG /8 3/8GG /2 /2GG /4 3/4GG GG44 - Unequal pipe connector - SPP 2 Part number C Weight 2 C /8 /4 /8x/4GG /8 3/8 /8x3/8GG /8 /2 /8x/2GG /4 3/8 /4x3/8GG /4 /2 /4x/2GG /8 /2 3/8x/2GG /2 /2xGG /4 /2 3/4x/2GG /4 3/4xGG WGG44 - ulkhead female union - etric or SPP C C Part number C C J T W Weight ax. J W T 5 5WGG44 0x /8 /8WGG44 6x /4 /4WGG44 20x /8 3/8WGG44 26x /2 /2WGG44 28x For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 0 Catalogue UK

233 CD43-90 female-male elbow - SPP-SPT Pneumatic adaptors Part number J N P Weight P J N /8 /8 /8CD /4 /4 /4CD /8 3/8 3/8CD /2 /2 /2CD /4 3/4 3/4CD CD CR33-90 equal male elbow - SPT Part number P Weight P /8 /8CR /4 /4CR /8 3/8CR /2 /2CR /4 3/4CR CR DD44-90 female pipe elbow - SPP J Part number J Weight /8 /8DD /4 /4DD /8 3/8DD /2 /2DD /4 3/4DD DD DD44KT - 90 bracketed equal female elbow - SPP Part number N Weight N ;; ;; ;; ;; ;; ;;; ;; ;; ;; ;;;;;;;;; ;;;;;;;;; ;;;; /2 /2DD44KT For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. Catalogue UK

234 Pneumatic adaptors O444 - Female pipe tee - SPP Part number J N Weight N J /8 /8O /4 /4O /8 3/8O /2 /2O /4 3/4O O RRS333 - ale pipe tee - SPT Part number N P Weight N P /8 /8RRS /4 /4RRS /8 3/8RRS /2 /2RRS /4 3/4RRS RRS RS433 - Run tee female-male-male - SPT-SPP-SPT N P J Part number J N P Weight /8 /8 /8RS /4 /4 /4RS /8 3/8 3/8RS /2 /2 /2RS /4 3/4 3/4RS RS S443 - ranch tee female-female-male - SPP-SPP-SPT N P J Part number J N P Weight /8 /8 /8S /4 /4 /4S /8 3/8 3/8S /2 /2 /2S /4 3/4 3/4S S For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 2 Catalogue UK

235 Pneumatic adaptors RO434 - Run tee female-male-female - SPP-SPT-SPP N P J Part number J N P Weight /8 /8 /8RO /4 /4 /4RO /8 3/8 3/8RO /2 /2 /2RO /4 3/4 3/4RO RO RRO334 - ranch tee male-male-female - SPT-SPT-SPP N P J Part number J N P Weight /8 /8 /8RRO /4 /4 /4RRO /8 3/8 3/8RRO /2 /2 /2RRO /4 3/4 3/4RRO RRO KOO4 - Female pipe cross - SPP Part number J Weight /8 /8KOO /4 /4KOO /8 3/8KOO /2 /2KOO J KRO Cross fem.-fem.-male-fem. - SPP-SPP-SPT-SPP Part number J P Weight /8 /8 /8KRO /4 /4 /4KRO /8 3/8 3/8KRO /2 /2 /2KRO J P For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 3 Catalogue UK

236 Pneumatic adaptors KRRS3 - ale pipe cross - SPT Part number P Weight /8 /8KRRS /4 /4KRSS /8 3/8KRSS /2 /2KRSS P Y444 - Y connector female - SPP C 90 J J Part number C J Weight /8 /8Y /4 /4Y /8 3/8Y /2 /2Y YS443 - Y connector female-female-male - SPP-SPP-SPT P C 90 Part number C J P Weight /8 /8 /8YS /4 /4 /4YS /8 3/8 3/8YS /2 /2 /2YS J P4UN - Hollow hex head plug - O-Ring sealing Part number C J 2 Weight J C 2 /8 /8P4UN /4 /4P4UN /8 3/8P4UN /2 /2P4UN For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 4 Catalogue UK

237 Pneumatic adaptors P80N - Hex head plug - etric J C Part number C J Weight 5 5P80N This part requires one RRD or RRP washer to order separately. P40N - Hex head plug - SPP Part number C J Weight J C /8 /8P4ON /4 /4P4ON /8 3/8P4ON /2 /2P4ON /4 3/4P4ON P4ON These parts require one RRD or RRP washer to order separately. HHP3 - Hollow hex head plug - SPT Part number C5 P Weight /8 /8HHP /4 /4HHP /8 3/8HHP /2 /2HHP C5 P FN4 - Hex head cap - SPP Part number C J Weight C /8 /8FN /4 /4FN /8 3/8FN /2 /2FN J For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 5 Catalogue UK

238 Pneumatic adaptors FGH - Female hose adaptor - SPP C Part number C J Weight 6 /8 FGH6-/ /8 FGH7-/ /4 FGH7-/ /4 FGH8-/ /4 FGH9-/ J 9 3/8 FGH9-3/ /8 FGH0-3/ /8 FGH2-3/ /2 FGH2-/ F3H - ale hose adaptor - SPT Part number C P Weight 6 /8 F3H6-/ /4 F3H6-/ /8 F3H7-/ /4 F3H7-/ /8 F3H8-/ /4 F3H8-/ /8 F3H9-/ /4 F3H9-/ /8 F3H9-3/ /2 F3H9-/ P C 0 /8 F3H0-/ /4 F3H0-/ /8 F3H0-3/ /2 F3H0-/ /4 F3H2-/ /8 F3H2-3/ /2 F3H2-/ /8 F3H4-3/ /2 F3H4-/ /8 F3H6-3/ /2 F3H6-/ /4 F3H6-3/ /8 F3H7-3/ /2 F3H7-/ /8 F3H8-3/ /2 F3H8-/ /4 F3H8-3/ /8 F3H20-3/ /2 F3H20-/ For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 6 Catalogue UK

239 F4H - ale hose adaptor - etric or SPP Pneumatic adaptors Part number C J Weight J C F4H /8 F4H7-/ /4 F4H7-/ /8 F4H8-/ /8 F4H9-/ /4 F4H9-/ /8 F4H9-3/ /4 F4H2-/ /8 F4H2-3/ /2 F4H2-/ /8 F4H7-3/ /2 F4H7-/ NIF - luminium manifold - SPP T Part number Q T Z Weight T Q Z /8 NIF/8KO4D /4 NIF/4KO4D /8 NIF3/8KO4D /2 NIF/2KO4D NI - luminium manifold - SPP 2 N Part number 2 Y Z Weight Z n Y 2 /8 5 7 NIx/8x5x /4 /8 2 NIx/4x/8x /4 /8 3 NIx/4x/8x /4 /8 4 NIx/4x/8x /4 /8 5 NIx/4x/8x /4 /8 6 NIx/4x/8x /8 /4 2 NIx3/8x/4x /8 /4 3 NIx3/8x/4x /8 /4 4 NIx3/8x/4x /8 /4 5 NIx3/8x/4x /8 /4 6 NIx3/8x/4x For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 7 Catalogue UK

240 Pneumatic adaptors NI2 - luminium manifold - SPP Z Y 2 N Part number 2 Y Z Weight n /4 /8 2 NI2x/4x/8x /4 /8 3 NI2x/4x/8x /4 /8 4 NI2x/4x/8x /4 /8 5 NI2x/4x/8x /8 /4 2 NI2x3/8x/4x /8 /4 3 NI2x3/8x/4x /8 /4 4 NI2x3/8x/4x /8 /4 5 NI2x3/8x/4x RRD - luminium washer 2 Size Part number 2 Weight 5 5RRD /8 /8RRD /4 /4RRD /8 3/8RRD /2 /2RRD RRP - Nylon washer Size Part number 2 Weight 2 5 5RRP /8 /8RRP /4 /4RRP /8 3/8RRP /2 /2RRP /4 3/4RRP RRP For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 8 Catalogue UK

241 all valves Catalogue 3529-UK

242 all valves edia Guide The table below lists general recommendations for the selection of valve materials. For specific cases, and for those not included in the edia Guide, it is advisable to check with your Parker representative. There are many specific environmental factors which may affect corrosion rate, such as temperature, solution, concentration and presence of impurities. Therefore, we recommend that the information be used only as a guide to material selection. If any questions exist regarding the expected performance of a material in a given application, actual tests should be performed to determine the suitability of the materials in question. Fluid rass Carbon steel Stainless steel (36) una N (Nitrile) Neoprene cetone E E E U U E U E E E cetylene G E E G P E E E E ir E E E E E E E E E E lcohol, ethyl G G G E G E E E E G lcohol, methyl E G E G E E P E E G nimal oil G G G E G G E G sphalt emulsion E G E U P U E E E G sphalt liquid E G E P P U E E E G eer G U E G G G E E E U enzene G G G U U U G E E utane E G E G G U E E E P Calcium chloride G P G E E G E E E U Carbonated water G G E E E E E E E E Caustic soda G E P G G E Coffee E E E E E E G Cutting oils E G E E G E E E Diesel oil fuels E E E E P U E E G Ethanol E U U U E E U G Ethyl alcohol G G G E E E E Ferrous sulphate G U G E E E E E E U Gas, natural G G E E E U E E E Gasoline, unleaded E E E P U E E E E Glucose E G E E E E E E E Glycerine G P E P U E G E P E Kerosene E G E E P U E E E G ethane E G E E G E E E ethanol G E G G U G E G ethyl alcohol G G G E G P E E ilk & milk products G U E E E E E E E G ineral oils G G E E G U E E E G Naphtha G G G G P U E E E G Natural gas, sour G G E E E U E E Nitric acid 00% U U E U U U G E U U Nitric acid 30% U U E P P G E E U U Nitrogen E E E E E G E E E G Paints & solvents E E E U U U G E G Paper pulp G E G G G G E Paraffin E G E E P U E E E Petrolatum (Petroleum Jelly) G P G E G E E E Propane gas E G G E G U E E E Sea water P U G E E E E E E Sodium chloride G P G E E G E E E E Steam (00 C) E E E U U G P E U Sulphur U P G U P G G E E Trichlorethylene G G G U U U G E E U Water, distilled E U E P G G E E E E Water, fresh E P E P G G E E E E EPR Fluorocarbon PTFE cetal Nylon (Polyamide) E = Excellent G = Good P = Poor U = Unsatisfactory 2 Catalogue 3529-UK

243 all valves Index VGC series - SPP short threads - General purpose female / female valve with lever handle SPP VGC - p. 5 female / female valve with compact handle SPP VGTC - p. 5 VG series - SPP long threads - General purpose female / female valve with lever handle SPP VG - p. 7 female / female valve with compact handle SPP VGT - p. 7 VG series - SPP short threads - Compact female / female valve SPP VG - p. 9 VG4POCK series - SPP-long threads - lockable vented valve 200 PSI female / female valve SPP VG4POCK - p. 3 Catalogue 3529-UK

244 all valves VGC series Principle Parker VGC series economy ball valves are designed for use in a wide variety of fluid applications. vailable with SPP female/female* short threads to ISO-228, they are full flow valves giving minimum pressure drop. The VGC series has a double PTFE seal on the ball enabling the valve to be used with flow in either direction. ll seals are treated with a silicone free lubricant enabling the valves to be used in water-based paint spray applications.-vgc series valves have an adjustable PTFE packing gland for easy maintenance and longer service For operator safety the VGC series valves are fitted with anti-extrusion stems to prevent blow out and all valves are 00% pressure tested to ensure zero leakage. * For other thread configurations please consult your Parker sales engineer. Technical features ody ever handle Compact handle nti extrusion stem Stem packing gland all nti friction ring Forcing nut Threads Pressure Nickel plated brass to DIN7660 and UNI5705 spec. Carbon steel with yellow PVC coating luminium with yellow epoxy coating Nickel plated brass PTFE rass chrome plated PTFE Nickel plated brass /4" - 2" SPP to ISO228/ DIN259 See chart below Operating pressures and temperatures /4" - 3/8" /2" 3/4" " /4" /2" 2" Pressure (bar) Temperature ( C) N.. This chart gives general information. Only testing under operating conditions will finally determine which valve should be selected. 4 Catalogue 3529-UK

245 all valves dvantages djustable packing The PTFE packing gland and adjustable washer are designed to give longer service life and lower operating torques. See instruction 3529-F/G/D contained in each box. nti extrusion stem The VGC series ball valves are fitted with an anti-extrusion stem to prevent blow out in the case of pressure peaks. Compact handle For applications where space is at a premium, the VGC series valve is available with a compact handle for sizes up to ". VGC - SPP female / female valve with lever handle DN Part number C H O I Weight mm O C H 8 /4 VG4-/4C /8 VG4-3/8C /2 VG4-/2C /4 VG4-3/4C VG4-C I 32./4 VG4-./4C /2 VG4-./2C VG4-2C This series is also available with red handle.-to order, add R to the part number, e VG4-/4CR. VGTC - SPP female / female valve with compact handle DN Part number C H O I Weight mm O C H 8 /4 VGT4-/4C /8 VGT4-3/8C /2 VGT4-/2C /4 VGT4-3/4C VGT4-C I For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 5 Catalogue 3529-UK

246 all valves VG series Principle Parker VG series valves are designed for use in fluid and gas applications and are DVGW approved.-the valve dimensions are in accordance with DIN3357 for interchangeability and are available with SPP female/female* long threads to DIN 2999/ ISO 228. These full flow ball valves have a chrome plated ball with a double PTFE seal system enabling the valve to be used with flow in either direction. ll seals are treated with a silicone free lubricant enabling the valves to be used in water based paint spray applications. VG series valves are fitted with an anti-extrusion stem with two Fluorocarbon seals for maximum safety and performance. fter assembly all valves are 00% pressure tested to ensure zero leakage. * For other thread configurations please consult us. Technical features ody ever handle Compact handle nti extrusion stem Stem seal all nti friction ring Forcing nut Valve dimensions Pressure rass nickel plated to DIN7660 and UNI5705 spec. Carbon steel with yellow PVC coating luminium with yellow epoxy coating rass nickel plated Two Fluorocarbon O-rings rass chrome plated PTFE rass nickel plated In accordance with DIN3357 See chart below Operating pressures and temperatures /4" - 3/8" /2" 3/4" " /4" /2" 2" Pressure (bar) Temperature ( C) N.. This chart gives general information. Only testing under operating conditions will finally determine which valve should be selected. 6 Catalogue 3529-UK

247 all valves dvantages DIN 2999 / ISO 228 female threads VG series valves are manufactured with long female threads in accordance to DIN 2999 / ISO 228. This enables the valves to be used with Prestolok, etrulok and brass adaptors but also Parker's range of steel hydraulic fittings and EO-fittings form or C to DIN nti extrusion stem The VG series ball valves are fitted with an anti extrusion stem to prevent blow out in the case of pressure peaks. The stem is sealed with two Fluorocarbon O-rings for maximum safety and performance. Full flow ll VG series valves are full-flow. This limits the turbulence created by the passage of fluid across the valve, minimizing pressure drop. VG- SPP female / female valve with lever handle DN Part number C H O I Weight mm 8 /4 VG4-/ /8 VG4-3/ /2 VG4-/ /4 VG4-3/ VG O C H I 32./4 VG4-./ /2 VG4-./ VG This series is also available with red handle.-to order, add R to the part number, e VG4-/4R. VGT - SPP female / female valve with compact handle DN Part number C H O I Weight mm O C H 8 /4 VGT4-/ /8 VGT4-3/ /2 VGT4-/ /4 VGT4-3/ VGT I 7 Catalogue 3529-UK

248 all valves VG series Principle The VG series ball valves with their compact design offer the solution to applications where space is an important factor. The body is of a particularly robust design. The integrity of the sealing on the ball is obtained by the use of PTFE seats. The valves are available with SPP female threads ISO-228/ (DIN 299) in : /4" 3/8" and /2". Technical features Handle nti-extrusion ody retention Handle Stem Stem seal all guide Nut Seat seals Pressure screw pin rass rass Polyamide rass Fluorocarbon rass Stainless rass PTFE See chart chromium chromium chromium steel below plated plated plated Operating pressures and temperatures 5 /8" - /4" - 3/8" Pressure (bar) 0 5 /2" Temperature ( C) 90 N.. This chart gives general information. Only testing under operating conditions will finally determine which valve should be selected. 8 Catalogue 3529-UK

249 all valves dvantages Design of the body The valve is manufactured from a solid section which incorporates the stem housing in the body. This design allows excellent guidance of the stem, which increases its lifespan. Stem tightness Fluorocarbon O-ring assembled under compression automatically compen-sates for minute friction wear. Thus a high standard of seal is Tightness of the seals The perfect tightness of the seals on the casing is obtained by the preset force of the nut, adjusted during assembly. VG - SPP female / female valve C H DN Part number C H I Weight mm 8 /4 VG4-/ /8 VG4-3/ /2 VG4-/ I vailability of the items : please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. 9 Catalogue 3529-UK

250 all valves VGPOCK series Principle Parker VGPOCK series of ball valves has been developed to meet the requirements of European Directive DI 89/392/CEE relating to the isolation of power supply and to meet the health and safety requirements for machines and materials in paragraphs of the Code du Travail. The VGPOCK series of ball valves incorporate two specific safety features : - n 5 threaded venting port enabling downstream pressure to be vented when the valve is closed. mechanism enabling the valve to be padlocked in the open position, thus preventing tampering or accidental closure of the valve during operation. ll seals are treated with a silicone free lubricant enabling them to be used in water based paint spray applications. Technical features ody ever handle nti extrusion stem Stem packing gland all nti friction ring Forcing nut Valve dimensions Pressure rass nickel plated to DIN7660 and UNI5705 spec. Carbon steel with yellow PVC coating rass nickel plated PTFE rass chrome plated PTFE rass nickel plated In accordance with DIN3357 See chart below Operating pressures and temperatures 5 /8" - /4" - 3/8" Pressure (bar) 0 5 /2" Temperature ( C) 90 N.. This chart gives general information. Only testing under operating conditions will finally determine which valve should be selected. 0 Catalogue 3529-UK

251 all valves Threaded exhaust VGPOCK series ball valves are manufactured with an 5 threaded exhaust port, this safety feature enables the downstream air pressure to be vented when the valve is closed. ockable handle The VGPOCK series ball valves are fitted with a handle that can be locked in the closed position with a padlock. This safety feature ensures the valve cannot be accidentally opened, and only authorised personel can operate the valve. DIN 2999 / ISO 228 female threads VGPOCK series valves are manufactured with female threads in accordance to DIN 2999/ ISO228. This enables the valves to be used with Prestolok, etrulok and brass adaptors but also Parker's range of steel hydraulic fittings and EO-fittings form or C to DIN nti extrusion stem The VGPOCK series ball valves are fitted with an anti-extrusion stem to prevent blow out in the case of pressure peaks. Full flow ll VGPOCK series valves are fullflow. This limits the turbulence created by the passage of fluid across the valve, minimizing pressure drop. djustable packing The PTFE packing gland and adjustable washer are designed to give longer service life and lower operating torques. VG4POCK - SPP-female / female lockable vented valve with lever handle 200 PSI C DN H DN Part number C G H I Weight 8 /4 VG4P-/4OCK /8 VG4P-3/8OCK /2 VG4P-/2OCK /4 VG4P-3/4OCK VG4P-OCK I 5 I G Catalogue 3529-UK

252 Quick Coupling Products Catalogue 3806-UK

253 Pneumatic couplings Index P series female body - male thread SPT P52 F3C - p. N 5 P53 F3C - p. N 5 P54 F3C - p. N 5 female body - female thread SPP P52 G4Z - p. N 5 P53 G4Z - p. N 5 P54 G4Z - p. N 5 female body - hose barb P52 E - p. N 5 male tip - male thread SPT P2 F3C - p. N 6 P3 F3C - p. N 6 P4 F3C - p. N 6 male tip - female thread SPP P2 G4Z - p. N 6 P3 G4Z - p. N 6 P4 G4Z - p. N 6 male tip - hose barb P2 E - p. N 6 P3 E - p. N 6 P4 E - p. N 6 male tip - Push-ok P2 P - p. N 6 P3 P - p. N 6 P4 P - p. N 6 PF series female body - male thread SPT PF52 F3C - p. N 8 female body - female thread SPP PF52 G4Z - p. N 8 female body - hose barb PF52 E - p. N 8 PF series female bodies are recommended for use with P series male tips (page N5) PS series female body male thread SPP PS p. N 0 PS p. N 0 PS p. N 0 female body female thread SPP PS F - p. N 0 PS F - p. N 0 PS F - p. N 0 female body hose barb PS H - p. N 0 PS H - p. N 0 PS H - p. N 0 For sizes /4 & 3/8, male tips to be used with PS female bodies are those of the P Series (page N5). For size /2, please use the male tips PS-502 with a specific treament especially designed to withstand high flows. male tip male thread SPT PS T - p. N 3 male tip female thread SPP PS F - p. N 3 male tip hose barb PS H - p. N 3 PE series N female body - male thread SPP PE52 F3C - p. N 3 female body - female thread SPP PE52 G4Z - p. N 3 female body - hose barb PE52 E - p. N 3 male tip - male thread SPP PE2 F3C - p. N 4 male tip - female thread SPP PE2 G4Z - p. N 4 male tip - hose barb PE2 E - p. N 4 male tip - Push-ok PE2 P - p. N 4 N 2 Catalogue 3806-UK

254 Pneumatic couplings Index PES series female body male thread SPP PES p. N 9 female body female thread SPP PES F - p. N 9 female body hose barb PES H - p. N 9 ale tips to be used with PES female bodies are those of the PEF Series (page N4). PEF series female body - male thread SPT PEF52 F3C - p. N 6 PEF53 F3C - p. N 6 female body - female thread SPP PEF52 G4Z - p. N 6 PEF53 G4Z - p. N 6 female body - hose barb PEF52 E - p. N 6 PEF53 E - p. N 6 male tip - male thread SPT PEF2 F3C - p. N 7 PEF3 F3C - p. N 7 male tip - female thread SPP PEF2 G4Z - p. N 7 PEF3 G4Z - p. N 7 male tip - hose barb PEF2 E - p. N 7 PEF3 E - p. N 7 male tip - Push-ok PEF2 P - p. N 7 PEF3 P - p. N 7 PCF series female body - male thread SPT PCF52 F3C - p. N 2 female body - female thread SPP PCF52 G4Z - p. N 2 female body - hose barb PCF52 E - p. N 2 male tip - male thread SPT PCF2 F3C - p. N 22 male tip - female thread SPP PCF2 G4Z - p. N 22 male tip - hose barb PCF2 E - p. N 22 N G series NPTF Thread G 44 - p. N 24 SPP Thread G 34 - p. N 24 N 3 Catalogue 3806-UK

255 P-Series Principle The P series of pneumatic quick couplers has been designed to meet the specifications and the profile defined in ISO standard Size : /4", 3/8", /2" - Valving on female half only : poppet. - eets the requirements of ISO 650-, US I-C409 and FNOR E End configuration : SP male and female, barb connector, Parker Push-ok. - One-hand operated (Push-toconnect). Technical features End adaptor aterial Female body Spring and ody Sleeve Poppet Pins Seals snap ring ale tip ody size Flow rates l/min. Temperature range ax. operating pressure rass rass (except on 3/8" steel yellow chromate plated) rass rass ISI 30 Stainless steel ISI 420 Stainless steel hardened 54HRC NR (Nitrile) Hardened steel nickel plated /4" 3/8" /2" From -20 C to + 00 C 6 bar pplications eeting an international standard, the /4" size P series pneumatic couplers are extensively used in the connection of pneumatic tools currently utilised in industry and garages. arger sizes (3/8" and /2") are used in pneumatic applications when larger flow rates are required, e. : grinding machines, pneumatic wrenches, pneumatic equipment, etc. Pressure drop Test with air, inlet pressure 6 bar N 0,7 0,7 0,7 0,6 0,6 0,6 Pressure drop (bar) 0,5 0,4 0,3 0,2 0, Pressure drop (bar) 0,5 0,4 0,3 0,2 0, Pressure drop (bar) 0,5 0,4 0,3 0,2 0, ir flow (l/min) /4" ir flow (l/min) 3/8" ir flow (l/min) /2" N 4 Catalogue 3806-UK

256 P-Series Pressure drop Tests with water Pressure drop (bar) Pressure drop (bar) Pressure drop (bar) Water flow (l/min) /4" Water flow (l/min) 3/8" Water flow (l/min) /2" P52/53/54 F3C - Female body - male thread SPT ody Part number d F 4 size /4 /4 P52 F3C /4 3/8 P52 F3C /8 /4 P53 F3C /8 3/8 P53 F3C /8 /2 P53 F3C /2 3/8 P54 F3C /2 /2 P54 F3C /2 3/4 P54 F3C P52/53/54 G4Z - Female body - female thread SPP ody Part number d F 4 size /4 /4 P52 G4Z /4 3/8 P52 G4Z /8 /4 P53 G4Z /8 3/8 P53 G4Z /8 /2 P53 G4Z /2 3/8 P54 G4Z /2 /2 P54 G4Z /2 3/4 P54 G4Z P52 E - Female body - hose barb N ody Part number d F 4 size mm /4 6 P52 E /4 8 P52 E /4 0 P52 E N 5 Catalogue 3806-UK

257 P series P2/3/4 F3C - ale tip - male thread SPT ody Part number 4 size /4 /8 P2 F3C /4 /4 P2 F3C /4 3/8 P2 F3C /8 /4 P3 F3C /8 3/8 P3 F3C /8 /2 P3 F3C /2 /2 P4 F3C /2 3/4 P4 F3C P2/3/4 G4Z - ale tip - female thread SPP ody Part number 4 size /4 /4 P2 G4Z /4 3/8 P2 G4Z /8 3/8 P3 G4Z /8 /2 P3 G4Z /2 /2 P4 G4Z /2 3/4 P4 G4Z P2/3/4 E - ale tip - hose barb ody Part number d 4 size mm /4 6 P2 E /4 8 P2 E /4 0 P2 E /8 6 P3 E /8 8 P3 E /8 0 P3 E /2 0 P4 E /2 3 P4 E /2 9 P4 E P2/3/4 P - ale tip - Push-ok ody Part number d 4 size /4 /4 P2 P /4 3/8 P2 P /8 /4 P3 P /8 3/8 P3 P /2 /2 P4 P /2 3/4 P4 P N For more information, please consult our catalogue 3800-G-F. N 6 Catalogue 3806-UK

258 PF series Principle PF series pneumatic quick couplers are only available in the /4" size and conform to specifications and profile of ISO standard 650-, while having improved flow capability. - Valving on female half only : poppet. - eets the requirements of ISO 650-, US I-C409 and FNOR E End configuration : SP male and female, barb connector. - One-hand operated (Push-to-connect). Technical features aterial Female body End adaptor ody Spring and Sleeve Poppet alls Seals snap ring ale tip ody size Flow rates l/min. Temperature range ax. operating pressure rass nickel plated rass nickel plated Steel hardened and nickel plated rass ISI 30 Stainless steel ISI 420 Stainless steel NR (Nitrile) Hardened steel nickel plated /4" 900 From -20 C to + 00 C 6 bar pplications The PF series comes from the same family as the P series, but has even better flow characteristics, enabling these couplers to be used with any type of pneumatic tool. This series can be used in place of larger size couplers, because the pressure drop has been greatly improved. N For more information, please consult our catalogue 3800-G-F. N 7 Catalogue 3806-UK

259 PF series Pressure drop Tests with air, inlet pressure 6 bar Tests with water 4 Pressure drop (bar) Pressure drop (bar) ir flow (l/min) /4" Water flow (l/min) /4" PF52F3C - Female body - male thread SPT ody size Part number d F 4 /4 /4 PF52 F3C /4 3/8 PF52 F3C PF52G4Z - Female body - female thread SPP ody size Part number d F 4 /4 /4 PF52 G4Z /4 3/8 PF52 G4Z PF52 E - Female body - hose barb ody size Part number d F 4 mm /4 6 PF52 E /4 8 PF52 E /4 0 PF52 E N Important : PF series female bodies are recommended for use with P series male tips (N 6). For more information, please consult our catalogue 3800-G-F. N 8 Catalogue 3806-UK

260 PS series Principle Parker PS Series combines many advantages : Easy operations and safety. low connection force allows an easy push-to-connect action. One handed disconnection permits air to vent safety. PS Series meets the ISO 444 and DIN EN983 specifications. The system is depressurised downstream prior to disconnection which will prevent hose whip. Ergonomics : this series is lightweight, robust in its construction and produced in impact resistant material to increase service life and resistance to abrasion, shocks, crushing and vibration. The plastic sleeve construction has also the advantage of protecting surfaces from scratchin ody sizes : /4, 3/8, /2. - Valving on female half only : streamlined poppet - eets the requirements of ISO 650- & US I- C409 - End configurations : SPP, SPT and hose barb. Technical features aterial Female body Spring and End adaptor ody Sleeve Poppet Clamps snap ring Seals ale tip ody size Flow rates Nl/min.* Temperature range ax. operating pressure Zinc plated steel Polyacetal Polyamide Polyamide Stainless steel (/4-3/8 ) Polyacetal Pins and balls (/2 ) Stainless steel NR (Nitrile) For sizes /4 & 3/8 Hardened steel nickel plated For size /2 carbontrided steel /4" 3/8 / From -5 C to + 70 C 6 bar *Rated flow at pressure drop of 0,6 bar and 6 bar inlet pressure. pplications Due to a streamlined poppet, the PS Series has high flow characteristics enabling them to be used with any type of pneumatic tool such as pneumatic spanners and cutters, grinding wheels, pneumatic hoists N Easy operations To decompress the down stream system, you just have to pull in the direction indicated on the arrow. thrust in the opposite direction is disconnecting the male tip in total safety. N 9 Catalogue 3806-UK

261 PS series Pressure drop Tests with air PS /4" PS 3/8" PS /2" 0,9 0,9 0,9 0,8 0,8 0,8 Pressure drop (bar) 0,7 0,6 0,5 0,4 0,3 Pressure drop (bar) 0,7 0,6 0,5 0,4 0,3 Pressure drop (bar) 0,7 0,6 0,5 0,4 0,3 0,2 0,2 0,2 0, 0, 0, ir flow (NI/min) ir flow (NI/min) ir flow (NI/min) PS - 25/37/ Female body - male thread SPP Size Part number d F 4 4 F d /4 /4 PS ,5 /4 3/8 PS /8 3/8 PS /8 /2 PS /2 /2 PS /2 3/4 PS PS - 25/37/50 - F - Female body - female thread SPP Size Part number d F 4 4 F d /4 /4 PS F /4 3/8 PS F /8 3/8 PS F /8 /2 PS F /2 /2 PS F /2 3/4 PS F PS - 25/37/50 - H - Female body - hose barb Size mm Part number d F 4 4 F d /4 6 PS H /4 8 PS H /4 0 PS H /8 8 PS H /8 0 PS H /2 3 PS H /2 6 PS H N N 0 Catalogue 3806-UK

262 PS series Important : For size /4 & 3/8, male tips to be used with PS female bodies are those of the P Series (page N6). For size /2, please use the male tips PS-502 with a specific treatment especially designed to withstand high flows. PS T - ale tip - male thread SPT 4 Size Part number 4 /2 3/8 PS T 7 82 /2 /2 PS T PS F - ale tip - female thread SPP Size Part number 4 /2 3/8 PS F /2 /2 PS F PS H - ale tip - hose barb 4 Size mm Part number /2 3 PS H /2 6 PS H N N Catalogue 3806-UK

263 PE series Principle Showing the same overall dimensions as corresponding size P couplers, the PE series offers the double advantage of a profile design widespread in Europe and improved flow performance due to a larger flow path (7.2 mm). - Valving on female half only : poppet. - End configuration : SP male and female, barb connector, Parker Push-ok. - One-hand operated (Push-to-connect). Technical features aterial Female body Spring and End adaptor ody Sleeve Valve Pins Seals snap ring ale tip ody size Flow rates l/min* Temperature range ax. operating pressure rass rass rass rass ISI 420 ISI 30 Stainless Stainless NR steel steel (Nitrile) hardened rass 54HRC 7.2 mm 000 From -20 C to 35 bar + 00 C * Rated flow at pressure drop of 0.5 bar and 6 bar inlet pressure. pplications ecause of their flow characteristics, the PE series of couplers satisfies most pneumatic applications and can even replace couplers of a different design, but of larger size. They are ideally used with all kinds of pneumatic hand tools. N For more information, please consult our catalogue 3800-G-F. N 2 Catalogue 3806-UK

264 PE series Pressure drop Tests with air, inlet pressure 6 bar. 0.8 Tests with water Pressure drop (bar) Pressure drop (bar) ir flow (l/min) /4" Water flow (l/min) /4" PE52 F3C - Female body - male thread SPP ody size mm Part number d F /4 PE52 F3C /8 PE52 F3C /2 PE52 F3C PE52 G4Z - Female body - female thread SPP ody size mm Part number d F /4 PE52 G4Z /8 PE52 G4Z /2 PE52 G4Z PE52 E - Female body - hose barb ody size mm Part number d F 4 mm PE52 E PE52 E PE52 E N For more information, please consult our catalogue 3800-G-F. N 3 Catalogue 3806-UK

265 PE series PE2 F3C - ale tip - male thread SPP ody size mm Part number /8 PE2 F3C /4 PE2 F3C /8 PE2 F3C PE2 G4Z - ale tip - female thread SPP ody size mm Part number /4 PE2 G4Z /8 PE2 G4Z /2 PE2 G4Z PE2 E - ale tip - hose barb ody size mm Part number Ø 4 mm PE2 E PE2 E PE2 E PE2 E PE2 P - ale tip - Push-ok ody size mm Part number d /4 PE2 P /8 PE2 P /2 PE2 P N For more information, please consult our catalogue 3800-G-F. N 4 Catalogue 3806-UK

266 PEF series Principle The PEF series are available in 7.2 and 0 mm nominal sizes with the same profile as PE series. However, flow characteristics are even better. - Valving on female half only : poppet. - End configuration : SP male and female, barb connector, Parker Push- ok. - One-hand operated (Push-to-connect). Technical features aterial Female body Spring and End adaptor ody Sleeve Poppet snap ring alls Seals ale tip ody size Flow rates l/min Temperature range ax. operating pressure rass nickel plated rass nickel plated Steel hardened and nickel plated rass ISI 30 Stainless steel ISI 420 NR Hardened Stainless (Nitrile) steel nickel steel plated 7.2 mm 0 mm From -20 C to + 00 C 6 bar pplications Showing exceptional flow characteristics, PEF series couplers are used in all pneumatic applications, where pressure drop has to be reduced to an absolute minimum, and energy saving is essential. Pressure drop Tests with air, inlet pressure 6 bar. 0.7 Tests with water Pressure drop (bar) Pressure drop (bar) 3 2 N ir flow (l/min) 7.2 mm Water flow (l/min) 7.2 mm Pressure drop (bar) Pressure drop (bar) ir flow (l/min) 0 mm Water flow (l/min) 0 mm N 5 Catalogue 3806-UK

267 PEF series PEF52/53 F3C - Female body - male thread SPT ody size mm Part number d F /4 PEF52 F3C /8 PEF52 F3C /2 PEF52 F3C /8 PEF53 F3C /2 PEF53 F3C PEF52/53 G4Z - Female body - female thread SPP ody size mm Part number d F /4 PEF52 G4Z /8 PEF52 G4Z /2 PEF52 G4Z /8 PEF53 G4Z /2 PEF53 G4Z PEF52/53 E - Female body - hose barb ody size mm Part number d F 4 mm PEF52 E PEF52 E PEF52 E PEF53 E PEF53 E PEF53 E PEF53 E N For more information, please consult our catalogue 3800-G-F. N 6 Catalogue 3806-UK

268 PEF series PEF2/3 F3C - ale tip - male thread SPT ody size mm Part number /8 PEF2 F3C /4 PEF2 F3C /8 PEF2 F3C /2 PEF2 F3C /4 PEF3 F3C /8 PEF3 F3C /2 PEF3 F3C PEF2/3 G4Z - ale tip - female thread SPP ody size mm Part number /4 PEF2 G4Z /8 PEF2 G4Z /2 PEF2 G4Z /8 PEF3 G4Z /2 PEF3 G4Z PEF2/3 E - ale tip - hose barb ody size mm Part number Ø 4 mm PEF2 E PEF2 E PEF2 E PEF3 E PEF3 E PEF3 E PEF3 E PEF2/3 P - ale tip - Push-ok ody size mm Part number d 4 0 /4 PEF3 P /8 PEF3 P N For more information, please consult our catalogue 3800-G-F. N 7 Catalogue 3806-UK

269 PES series Principle Parker PES Series combines many advantages : Easy operations and safety. low connection force allows an easy push-to-connect action. One handed disconnection permits air to vent safety. PES Series meets the ISO 444 and DIN EN983 specifications. The system is depressurised downstream prior to disconnection which will prevent hose whip. Ergonomics : this series is lightweight, robust in its construction and produced in impact resistant material to increase service life and resistance to abrasion, shocks, crushing and vibration. The plastic sleeve construction has also the advantage of protecting surfaces from scratchin ody size : 7.2 mm. - Valving on female half only : streamlined poppet - eets the requirements of Europrofile - End configurations : SPP, SPT and hose barb. Technical features aterial Female body End adaptor ody Sleeve Spring and Pins and Poppet Seals snap ring balls ale tip ody size Flow rates Nl/min.* Temperature range ax. operating pressure Zinc plated steel Stainless steel Stainless steel NR (Nitrile) Polyacetal Polyamide Polyamide carbontrided steel 7.2 mm 470 From -5 C to + 70 C 6 bar *Rated flow at pressure drop of 0,6 bar and 6 bar inlet pressure. pplications Due to a streamlined poppet, the PES Series has high flow characyeristics enabling them to be used with any type of pneumatic tool such as pneumatic spanners and cutters, grinding wheels, pneumatic hoists Easy operations N To decompress the down stream system, you just have to pull in the direction indicated on the arrow. trust in the opposite direction is disconnecting the male tip in total safety. N 8 Catalogue 3806-UK

270 PES series Pressure drop Tests with air PES 7.2 mm 0,9 0,8 Pressure drop (bar) 0,7 0,6 0,5 0,4 0,3 0,2 0, ir flow (NI/min) PES Female body - male thread SPP d Size mm Part number d F /4 PES /8 PES F PES F - Female body - female thread SPP d Size mm Part number d F /4 PES F /8 PES F F PES H - Female body - hose barb Size mm Part number d F 4 d PES H PES H PES H N 4 F Important : ale tips to be used with PES female bodies are those of the PEF Series (page N5). N 9 Catalogue 3806-UK

271 PCF series Principle The PCF series, available in the /4" body size, has been designed to meet the profile defined in ISO standard 650-C. It has very good flow capability. - Valving on female half only : poppet eets the requirements of ISO 650-C - End configuration : SP male and female, barb connector - One-hand operated (Push-to-connect) Technical features End adaptor aterial Female body ody Sleeve Poppet Spring and alls Seals snap ring ale tip ody size Flow rates l/min Temperature range ax. operating pressure rass nickel plated rass nickel plated Steel hardened and nickel plated rass ISI 30 ISI 420 Stainless Stainless steel steel NR (Nitrile) Hardened steel, nickel plated From -20 C /4" 970 to 5 bar + 00 C pplications The /4" size PCF series pneumatic couplers are extensively used in the connection of pneumatic tools currently utilised in industry. N For more information, please consult our catalogue 3800-G-F. N 20 Catalogue 3806-UK

272 PCF series Pressure drop Tests with air, inlet pressure 6 bar. 0,7 0,6 Tests with water 4 3,5 Pressure drop (bar) 0,5 0,4 0,3 0,2 0, Pressure drop (bar) 3 2,5 2,5 0, ir flow (l/min) Water flow (l/min) PCF52F3C - Female body - male thread SPT ody size Part number d F 4 /4 /4 PCF52F3C /4 3/8 PCF52F3C /4 /2 PCF52F3C PCF52G4Z - Female body - female thread SPP ody size Part number d F 4 /4 /4 PCF52G4Z /4 3/8 PCF52G4Z /4 /2 PCF52G4Z PCF52E - Female body - hose barb ody size Part number d F 4 mm /4 6 PCF52E /4 8 PCF52E /4 0 PCF52E N For more information, please consult our catalogue 3800-G-F. N 2 Catalogue 3806-UK

273 PCF series PCF2F3C - ale tip - male thread SPT ody size Part number 4 /4 /4 PCF2F3C /4 3/8 PCF2F3C PCF2G4Z - ale tip - female thread SPP ody size Part number 4 /4 /4 PCF2G4Z /4 3/8 PCF2G4Z PCF2E - ale tip - hose barb ody size Part number Ø 4 mm /4 6 PCF2E /4 8 PCF2E /4 0 PCF2E N For more information, please consult our catalogue 3800-G-F. N 22 Catalogue 3806-UK

274 G series Principle The blow guns of the G Series are available with a variety of nozzle configurations. They combine many advantages : light weight, reduced noise level, easy control, ergonomic design and variable flow, thus providing superior performance. - Standard : nozzles available that meet OSH requirements - Inlet port : /4 NPTF and /4 SPP Technical features aterial : Impact resistant plastic. Pistol grip trigger : llows greater control over the amount of air delivered. Dual hooks for hangin Ergonomic lever : For an easy, instantaneous handling, without effort. Nozzles : - extended nozzles allow air to be focused where it is needed - short nozzles also available. Standards : ost models meet OSH directives on the use of compressed air for cleaning purposes. OSH directive #00- states that when dead ending occurs a static pressure at the main orifice shall not exceed 2 bar. For those blow guns that do not meet this requirement, OSH requires that compressed air shall not be used for cleaning purposes except where reduced to less than 2 bar, and then only with effective chip guarding and personal protective equipment (section 29 CFR paragraph b). Please refer to the blow gun descriptions on the next page for compatibility with OSH directive #00-. Temperature range Rated pressure (bar) 20 C +50 C 2 pplications G Series blow guns can be used at all the manufacturing stages to : - blow off parts - clean work-stations - remove dust - dry N N 23 Catalogue 3806-UK

275 G series low Guns Thread Description eets OSH requirements Colour yes no black grey Part Number /4 NPTF Extended nozzle G442-S /4 NPTF Extended nozzle G442-SGY /4 NPTF Extended nozzle G44-N /4 NPTF Short nozzle G444-S /4 NPTF /8 female NPT G443-N thread Thread Description eets OSH requirements Colour yes no black grey Part Number /4 SPP Extended nozzle G342-S /4 SPP Extended nozzle G34-N /4 SPP Short nozzle G344-S N N 24 Catalogue 3806-UK

276 Push-ok Hoses & Fittings Catalogue 4482-UK

277 Push-ok Hoses and fittings Index Hoses 80 - Push-ok Hose for low pressure applications Push-ok Hose for Phosphate ester Fluids Push-ok Hose with textile braided outer cover 7 82FR - Push-ok Hose with Fire-resistant cover Push-ok Hose for all standard industrial applications Push-ok Hose for high Oil Temperatures Push-ok for standard applications in the automotive industry 9 Fittings Page Fittings Page NPTF ale Pipe Female NPTF Pipe JIC 37 ale JIC 37 Swivel Female SE 45 Swivel female NPTF Swivel ale Pipe 22 3D82 - etric Standpipe ight Series Inch Standpipe (rass) JIC 37 Swivel Female 45 Elbow JIC 37 Swivel Female 90 Elbow JIC 37 Swivel Female 90 Elbow anjo Union DIN C Cone Swivel Female 5 36C Cone Swivel Female SE 45 swivel female 45 elbow SE 45 swivel female 90 elbow 25 37C Cone Swivel Female Push-ok Union SP Taper ale SP Swivel Female DIN ight Series etric Swivel Female 45 Elbow 2 39C82 - DIN ight Series etric Swivel Female 90 Elbow 2 3F82 - ale SP Parallel Pipe - Rigid Straight (with O-Ring Seal) SP Swivel Female 45 Elbow SP Swivel Female 90 Elbow 9 3C082 - DIN C Very ight Series etric Swivel Female 4 3C382 - DIN ight Series etric Swivel Female 0 3C482 - DIN ight Series etric Swivel Female 45 Elbow 3C582 - DIN ight Series etric Swivel Female 90 Elbow 3C82 - DIN N ight Series etric Swivel Female 3 3CE82 - DIN N ight Series etric Swivel Female 45 Elbow 3 3CF82 - DIN N ight Series etric Swivel Female 45 Elbow 4 3D082 - DIN D ight Series ale Stud 4 3D982 - SP ale Stud (Form ) 9 3DE82 - Double anjo Union 28 3DP82 - etric Swivel Female Tee / ale Stud 7 3DR82 - etric Swivel Female Tee 8 3DS82 - etric Swivel Female Tee / Standpipe 8 3EG82 - Straight daptor 6 3EV82-45 Elbow daptor 7 3EW82-90 Elbow daptor 7 3F82 - French etric 27 3FF82 - etru-ok Swivel Female 27 3J82 - ORFS Swivel Female 90 Elbow 26 3J782 - ORFS Swivel Female 45 Elbow 26 3J982 - ORFS Swivel Female 90 Elbow 26 3JC82 - ORFS Swivel Female (Short) 25 3J82 - ORFS ale 26 3VW82- Push-in Connector (VW Standard 39-V-669) 29 /R - anjo olt (DIN 7643) 29 H Female (Ford Standard UWR ) 30 H ale (Ford Standard UWR ) C3X8H22 - ale nipple 90 elbow (Ford Standard UWR ) 3 4-4C63X8H22 - ale swivel nut 90 elbow (Ford Standard UWR ) F3X83 - ale nipple straight fitting (Ford Standard UWR ) 3 4-4F63X832 - ale swivel nut straight fitting (Ford Standard UWR ) V3X8H7 - ale nipple 45 elbow (Ford Standard UWR ) 3 4-4V63X8H7 - ale swivel nut 45 elbow (Ford Standard UWR ) 32 VW2 - SP Swivel Female (VW Standard 39-V-663) 30 VW39D - VW-Push In Connector (VW Standard 39D-40) 30 O O 2 Catalogue 4482-UK

278 Push-ok Hoses and fittings Index ssembly ccessories Page ssembly instructions 5 Push-ok cut off and assembly tools 5 Chemical resistance For your safety! Flexible hoses are used to transmit fluids, sometimes at considerable pressures. The power-grip connection between the fitting and the hose is a critical zone in all flexible hose connections. Only use Parker components (hoses and nipples) designed to be assembled by means of the appropriate Parker tooling, which will ensure full compliance with standards. Following installation recommendations and suitable maintenance also give a guarantee for long life of the flexible hose. Non-compliance with these elementary rules can lead to the rupture of a flexible hose and cause considerable damage and sometimes bodily injury. O O 3 Catalogue 4482-UK

279 Push-ok Hoses and fittings Push-ok : an effective cost saving hose High-quality elastomer cover - excellent flexibility and resistance to abrasion Extruded synthetic rubber. Inner liner is resistant to petroleum-based oil, air and water Fibre braid reinforcement layer is impregnated with synthetic rubber for added durability Colour coding, a valuable Push-ok hose advantage 80 - hose is manufactured in grey, black, red and green hose is manufactured in black hose is manufactured in black. 82FR - hose is manufactured in black, blue, green and white hose is manufactured in black, blue, green and red hose is manufactured in blue hose is manufactured in black, blue, green, red and grey. Easy and fast identification of hose lines, where many hoses carry different fluids (e. oil, water, air, solutions, etc.) Immediate control and/or replacement of hose assemblies due to specific colours for diameters and lengths. Easy preventive maintenance Reduced maintenance time, when colours identify specific maintenance periods GR (GREY) RED (RED) K (CK) WHT (WHITE) O U (UE) GRN (GREEN) OR (ORNGE) RN (ROWN) Please put the colour code at the end of your part number to get the correct hose. O 4 Catalogue 4482-UK

280 Push-ok assembly instructions. Cut the hose right angled with a sharp knife. If necessary it is possible to use a lubricant (water/ soap solution with 5% soap fluid and 95% water) for easy assembly (exception 837). Push-ok disassembly instructions Push-ok Hoses and fittings 2. Insert fitting into hose until first barb is in hose. Place end of fitting against a flat object (bench, door, wall) and grip hose approximately " from end and push with a steady force until end of hose is covered by the yellow plastic collar. lternatively please use the Parker ssembly Tool No. 6050G. ttention! During assembly please note that Push-ok fittings will provide an effective grip only when the Push-ok hose is pushed fully on the insert, where the cropped end of the hose should be fully concealed by the plastic collar. For easy assembly of hose 837 please use only Push-ok ssembly Oil No. H Push-ok ssembly Oil is free from wetting disturbing substances. Don t use oil, lubricant or soap fluids for this hose!. Cut lengthwise along a line at approximately a 20 angle from centre line of hose. The cut should be approximately " lon e careful not to nick barbs when cutting the hose. 2. Grip hose and give a sharp downward tug to disengage from fittin ttention! efore re-use of the nipple please check nipple for damage. Damaged nipples can cause leakage. Push-ok assembly oil H89637 Water-oil emulsion for easier assembly of Parker Push-ok fittings. This product is very useful in combination with 837 hose (labs-free). Our Push-ok assembly oil is also free from wetting disturbing substances, like e. silicone. -litre bottle Part No. H89637 ssembly tool Tool designed for assembly of Push-ok fittings and hose in all sizes. Toggle actions greatly reduce effort necessary to hold hose and press in fittin Only a few pounds of force are needed on either handle to quickly assemble any size. Overall length: 320 mm Weight: 2,2 kg Part No. 6050G O O 5 Catalogue 4482-UK

281 Push-ok Hoses and fittings 80 - Push-ok Hose for low pressure applications Hose construction : Synthetic rubber tube; one fibre braid reinforcement; oil and weather resitant synthetic rubber cover. Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, air, water and water-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+00 C Exceptions :... ir max. +70 C Water max C pplications : ow pressure shopfloor air systems, pneumatic systems and general industrial and maintenance applications. Restrictions : Not recommended for compressed air brakes, transportation of flammable fluids, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Not recommended for fuel lines. Fittings: 82 series Pressure rating Part Hose ax. dynamic in. burst Vacuum in. bend Number Hose-I.D. O.D. working pressure pressure Kilo radius Weight DN Inch Size mm mm Pa psi Pa psi Pascal* mm kg/m 80-4-XXX-R 6 / XXX-R 0 3/ XXX-R 2 / XXX-R 6 5/ XXX-R 20 3/ R * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa Note: when ordering, specify Push-ok hose part number, followed by size, followed by colour. Example: 80-4-XXX-R XXX = K = black U = blue RED = red GRN = green GR = grey Example: 80-4-GRN-R (green) R = only available on reels 80-6-R is only available in grey Push-ok Hose for Phosphate ester Fluids Hose construction : EPD synthetic rubber tube; a single fibre braid reinforcement and a black, EPD synthetic rubber cover. Fluid compatibility : Water, water glycol emulsions, air, phosphate ester based hydraulic fluids. Do not allow tube to contact any petroleum based fluids. Use liquid soap as lubricant. Further details are listed in the chemical chart. Temperature range: Phosphate ester Hydraulic fluids C to +80 C Exceptions: ir... max.+70 C Water... max. +93 C pplications : ow pressure service hose ideally suited for general pneumatic applications (including dry air), water, water-glycol and phosphate ester based hydraulic fluids. Restrictions : Not recommended for compressed air brakes, transportation of flammable gases, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Fittings: 82 series Part Number Hose O.D. mm Pressure rating ax. dynamic working pressure in. burst pressure Pa psi Pa psi in. bend radius mm Hose-I.D. Weight DN Inch Size mm kg/m R 6 / R 0 3/ R 2 / R 20 3/ R = only available on reels O Only items priced in current price list are carried in stock. O 6 Catalogue 4482-UK

282 82 - Push-ok Hose with textile braided outer cover Push-ok Hoses and fittings Hose construction : Synthetic rubber tube; one textile braid reinforcement; abrasion, oil and weather resistant black textile braided cover Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, water, water-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+00 C Exceptions : ir... max. +70 C Water... max. +85 C pplications : Shopfloor air systems and general industrial, maintenance and automotive applications for air, water, lubricating oils and antifreeze. Restrictions : Not recommended for compressed air brakes, transportation of flammable fluids, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Not recommended for fuel lines. Fittings : 82 series Part number DN Hose-I.D. Inch Size mm Hose O.D. mm ax. dynamic working pressure Pa psi Pressure rating in. burst pressure psi Vacuum Kilo Pascal* in. bend radius mm / / / / / * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa Reels (R) available upon request. Pa Weight kg/m 82FR - Push-ok Hose with Fire-resistant cover Hose construction : Synthetic rubber tube; one fibre braid reinforcement; weld spark, oil- and mildew resistant black, blue, green, white or brown fibre braided cover. Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, water, water-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+00 C ir... max. +70 C Water... max. +85 C pplications : Compressed air systems, general industrial, maintenance and automotive applications. Suitable in welding areas where sparks are prevalent. Restrictions : Not recommended for compressed air brakes, transportation of flammable fluids, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Not recommended for fuel lines. Fittings : 82 series Part number DN Hose-I.D. Inch Size mm Hose O.D. mm ax. dynamic working pressure Pa psi Pressure rating in. burst pressure psi Vacuum Kilo Pascal* in. bend radius mm 82FR-4-XXX-R 6 / FR-6-XXX-R 0 3/ FR-8-XXX-R 2 / FR-2-XXX-R 20 3/ Pa Weight kg/m O * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa Note: when ordering, specify Push-ok hose part number, followed by size, followed by colour. Example: 82FR-4-XXX-R XXX = K = black U = blue GRN = green WHT =white RN = brown Example: 82FR-4-GRN-R (green) R = only available on reels Only items priced in current price list are carried in stock. O 7 Catalogue 4482-UK

283 Push-ok Hoses and fittings 83 - Push-ok Hose for all standard industrial applications Hose construction : Synthetic rubber tube; one fibre braid reinforcement; black, green, blue or red oil and weather resistant synthetic rubber cover. Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, water, water-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+00 C ir... max. +70 C Water... max. +85 C pplications : ow pressure shopfloor air systems, pneumatic systems and general industrial, maintenance and automotive applications. Restrictions : Not recommended for compressed air brakes, transportation of flammable fluids, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Not recommended for fuel lines. Fittings : 82 series Part number DN Hose-I.D. Inch Size mm Hose O.D. mm ax. dynamic working pressure Pa psi Pressure rating in. burst pressure psi * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa Note: when ordering, specify Push-ok hose part number, followed by size, followed by colour. Example: 83-4-XXX-R XXX = K = black U = blue RED = red GRN = green Example: 83-4-GRN-R (green) R = only available on reels Vacuum Kilo Pascal* in. bend radius 83-4-XXX-R 6 / XXX-R 0 3/ XXX-R 2 / XXX-R 6 5/ XXX-R 20 3/ Pa Push-ok Hose for high Oil Temperatures Weight Hose construction : PKR elastomer tube; one fibre braid reinforcement; blue PKR elastomer cover, with an embossed layline for permanent identification. Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, water, water-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+50 C ir... max. +70 C Water:... max. +85 C pplications : Industrial machinery and engine compartments with high operating temperature level, shopfloor air systems, and widespread industrial and maintenance applications. Restrictions : Not recommended for compressed air brakes, transportation of flammable fluids, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Not recommended for fuel lines. Fittings : 82 series Part number DN Hose-I.D. Inch Size mm Hose O.D. mm ax. dynamic working pressure Pa psi Pressure rating in. burst pressure psi Vacuum Kilo Pascal* in. bend radius mm R 6 / R 0 3/ R 2 / R 6 5/ Pa Weight kg/m O * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa R = only available on reels Only items priced in current price list are carried in stock. O 8 Catalogue 4482-UK

284 Push-ok Hoses and fittings abs-free with abrasion resistant cover (for standard applications in the automotive industry) Hose construction : Synthetic rubber tube; one fibre braid reinforcement; highly abrasion and weather resistant black, grey, green, blue or red synthetic rubber cover. This hose is free of any wetting disturbing substances eg: silicone Fluid compatibility : ineral based hydraulic and lubricating oils, coolant, antifreeze, water*, water*-oil emulsions. Further details are listed in the chemical chart. Temperature range : C/+00 C ir:... max. +70 C Water*:... max. +85 C pplications : The hose meets the automotive industry's requirement to be free from wetting disturbing substances. Suitable for robot lines, paint spraying air supply lines, pneumatic systems and general industrial applications. Restrictions : Not recommended for compressed air brakes, transportation of flammable gases, hydraulic or other applications where extreme pulsations are encountered. lso not recommended for thyristor cooling applications. Fittings : 82 series Note : for assembly see notes on page 5. Part number DN Hose-I.D. Inch Size mm Hose O.D. mm ax. dynamic working pressure Pa psi Pressure rating in. burst pressure psi * = the vacuum values listed in the table are vacuum pressure values in kpa. For an absolute value subtract the table value from 0kPa Note: when ordering, specify Push-ok hose part number, followed by size, followed by colour. Example: XXX-R XXX = K = black U = blue RED = red GRN = green GR = grey Example: GRN-R (green) R = only available on reels Vacuum Kilo Pascal* in. bend radius mm XXX-R 6 / XXX-R 0 3/ XXX-R 2 / XXX-R 6 5/ XXX-R 20 3/ Pa Weight kg/m O Only items priced in current price list are carried in stock. O 9 Catalogue 4482-UK

285 Push-ok Hoses and fittings C3 - DIN ight Series etric W Tube Part Hose-I.D. Thread O.D. W Number DN Inch Size mm metric mm mm mm mm 3C / x C / x C K 6 / x C C 6 / x C / x C / x C K 6 / x C C 6 / x C / x C K 6 / x C C 6 / x C / x C / x C K 0 3/ x C C 0 3/ x C / x C K 0 3/ x C C 0 3/ x C / x C / x C K 2 / x C / x C / x C C 6 5/ x C / x C / x C K 20 3/ x C x C K x C K x C C-K x and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass K = rass without plastic ring C = Stainless Steel K = Without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 0 Catalogue 4482-UK

286 Push-ok Hoses and fittings C4 - DIN ight Series etric Swivel Female 45 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm 3C / x C / x C / x C / x C C 6 / x C / x C / x C C 0 3/ x C / x C / x C / x C / x C / x C / x C / x C / x C / x C K x and K parts have brass nipples and steel nuts. C5 - DIN ight Series etric Swivel Female 90 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm 3C / x C C 6 / x C / x C / x C C 6 / x C / x C / x C / x C C 2 / x C / x C C 6 5/ x C / x C K x and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel K = Without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O Catalogue 4482-UK

287 Push-ok Hoses and fittings 9 - DIN ight Series etric Swivel Female 45 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm K 6 / x K 6 / x K 0 3/ x K 0 3/ x K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. 9C - DIN ight Series etric Swivel Female 90 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm 39C82-6-4K 6 / x C82-8-4K 6 / x C82-0-6K 0 3/ x C82-2-6K 0 3/ x C82-5-8K 2 / x ody in brass, swivel nut zinc plated, yellow chromated. Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. O aterial: without suffix = zinc plated - yellow chromated mild steel K = rass without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 2 Catalogue 4482-UK

288 Push-ok Hoses and fittings C - DIN N ight Series etric Swivel Female W Tube Part Hose-I.D. Thread O.D. W Number DN Inch Size mm metric mm mm mm mm 3C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x C / x and K parts have brass nipples and steel nuts. Fittings with standard O-Ring seals can be used for temperatures from -30 C up to +05 C. Find O-Rings in catalogue 4400-UK section I. Special O-Rings are available on request. CE - DIN N ight Series etric Swivel Female 45 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm 3CE / x CE / x CE / x CE / x CE / x CE / x CE / x CE / x and K parts have brass nipples and steel nuts. Fittings with standard O-Ring seals can be used for temperatures from -30 C up to +05 C. Find O-Rings in catalogue 4400-UK section I. Special O-Rings are available on request. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 3 Catalogue 4482-UK

289 Push-ok Hoses and fittings CF - DIN N ight Series etric Swivel Female 90 Elbow E W Tube Part Hose-I.D. Thread O.D. E W Number DN Inch Size mm metric mm mm mm mm mm 3CF / x CF / x CF / x CF / x CF / x CF / x CF / x CF / x CF / x and K parts have brass nipples and steel nuts. Fittings with standard O-Ring seals can be used for temperatures from -30 C up to +05 C. Find O-Rings in catalogue 4400-UK section I. Special O-Rings are available on request. C0 - DIN C Very ight Series etric Swivel Female W Tube Part Hose-I.D. Thread O.D. W Number DN Inch Size mm metric mm mm mm mm 3C / x C / x and K parts have brass nipples and steel nuts. D0 - DIN D ight Series ale Stud aterial: H without suffix = zinc plated - yellow chromated mild steel = rass K = rass without plastic ring C = Stainless Steel Tube Part Hose-I.D. Thread O.D. H Number DN Inch Size mm metric mm mm mm mm 3D / x D / x D / x D / x D K 0 3/ x D / x D C 0 3/ x D / x D / x D K 2 / x D / x D / x D / x D K 20 3/ x O For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 4 Catalogue 4482-UK

290 D - etric Standpipe ight Series Push-ok Hoses and fittings D Tube Part Hose-I.D. O.D. D Number DN Inch Size mm mm mm mm mm 3D / D / D82-6-4K 6 / D / D / D82-8-4K 6 / D / D / D82-0-6K 0 3/ D / D / D82-2-6K 0 3/ D82-2-8C 2 / D / D82-5-8K 2 / D / D82-5-8K 2 / D82-5-8CK 2 / D82-8-8K 2 / D / D / D82-8-0K 6 5/ D / D / D K 20 3/ Not recommended for new construction. Instead use C3 or C. ttention: For assembly of nut and sleeve use pre-assembly body. 5C Cone Swivel Female W Part Hose-I.D. Thread W Number DN Inch Size mm metric mm mm mm 35C82-2x-4K 6 / x C82-6-4K 6 / x C82-0-6K 0 3/ x C82-5-8K 2 / x C82-8-0K 6 5/ x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass K = rass without plastic ring C = Stainless Steel K = Without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 5 Catalogue 4482-UK

291 Push-ok Hoses and fittings 6C Cone Swivel Female - 45 Elbow E W Part Hose-I.D. Thread E W Number DN Inch Size mm metric mm mm mm mm 36C82-2x-4K 6 / x C82-6-4K 6 / x C82-0-6K 0 3/ x C82-5-8K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. 7C Cone Swivel Female - 90 Elbow E W EG - Straight daptor - etric / SP Taper Part Hose-I.D. Thread E W Number DN Inch Size mm metric mm mm mm mm 37C82-2x-4K 6 / x C82-6-4K 6 / x C82-0-6K 0 3/ x C82-5-8K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. aterial: G2 W G without suffix = zinc plated - yellow chromated mild steel K = rass without plastic ring = rass Tube Thread Part O.D. G G2 w Number mm metric SP mm mm EG6-/8 6 2x / EG6-/4 6 2x / EG8-/8 8 4x.5 / EG8-/4 8 4x.5 / EG8-3/8 8 4x.5 3/ EG0-/8 0 6x.5 / EG0-/4 0 6x.5 / EG0-3/8 0 6x.5 3/ EG0-/2 0 6x.5 / EG2x5-/8 2 2x.5 / EG2-/4 2 8x.5 / EG2x5-/4 2 2x.5 / EG5-3/8 5 22x.5 3/ EG5-/2 5 22x.5 / EG8-/2 8 26x.5 / EG8-3/4 8 26x.5 3/ Standard material: brass O For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 6 Catalogue 4482-UK

292 EV - 45 Elbow daptor - etric / SP Taper Push-ok Hoses and fittings G2 G Tube Thread Part O.D. G G2 Number mm metric SP mm EV6-/8 6 2x /8 20 EV6-/4 6 2x /4 20 EV8-/4 8 4x.5 /4 27 EV8-3/8 8 4x.5 3/8 27 EV0-/4 0 6x.5 /4 27 EV0-3/8 0 6x.5 3/8 27 EV5-/2 5 22x.5 /2 30 Standard material: brass EW - 90 Elbow daptor - etric / SP Taper G2 G Tube Thread Part O.D. G G2 Number mm metric SP mm EW6-/8 6 2x /8 20 EW6-/4 6 2x /4 20 EW8-/4 8 4x.5 /4 27 EW8-3/8 8 4x.5 3/8 27 EW0-/4 0 6x.5 /4 27 EW0-3/8 0 6x.5 3/8 27 EW2x5-/8 2 2x.5 /8 20 EW2x5-/4 2 2x.5 /4 20 EW5-/2 5 22x.5 /2 30 Standard material: brass DP - etric Swivel Female Tee / ale Stud H E W Part Hose-I.D. Thread E H W Number DN Inch Size mm metric mm mm mm mm mm DP-6-6-4K 6 / x DP-8-8-4K 6 / x DP-0-0-6K 0 3/ x DP-5-5-8K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel K = rass without plastic ring = rass For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 7 Catalogue 4482-UK

293 Push-ok Hoses and fittings DR - etric Swivel Female Tee H F E W Part Hose-I.D. Thread E F H W Number DN Inch Size mm metric mm mm mm mm mm mm DR-6-4-4K 6 / x DR-0-6-6K 0 3/ x DR-5-8-8K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. DS - etric Swivel Female Tee / Standpipe E W H F Tube Part Hose-I.D. Thread O.D. E F H W Number DN Inch Size mm metric mm mm mm mm mm mm mm DS-6-6-4K 6 / x DS-6-8-4K 6 / x DS-0-0-6K 0 3/ x DS-0-2-6K 0 3/ x DS-5-5-8K 2 / x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts SP Swivel Female W Hose-I.D. Part SP W Number DN Inch Size mm thread mm mm mm / /4x C 6 / /4x / /8x / /2x C 2 / /2x / /8x / /8x / /4x C 20 3/ /4x Standard nipples are stocked without plastic collar. If you need a collar, delete K from the part number. and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 8 Catalogue 4482-UK

294 - SP Swivel Female 45 Elbow Push-ok Hoses and fittings E W Part Hose-I.D. SP E W Number DN Inch Size mm thread mm mm mm mm / /4x / /8x / /2x / /8x / /8x / /4x K x and K parts have brass nipples and steel nuts. 2 - SP Swivel Female 90 Elbow E W Hose-I.D. Part SP E W Number DN Inch Size mm thread mm mm mm mm / /4x / /8x / /2x / /8x / /8x / /8x / /4x / /4x C 20 3/ /4x K x and K parts have brass nipples and steel nuts. D9 - SP ale Stud (DIN Form ) H Hose-I.D. Part SP H Number DN Inch Size mm thread mm mm mm 3D / /8x D / /4x D / /4x D / /8x D / /2x D / /2x D / /2x D / /8x D / /4x O aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel K = Without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 9 Catalogue 4482-UK

295 Push-ok Hoses and fittings 9 - SP Taper ale H Hose-I.D. Part SP H Number DN Inch Size mm thread mm mm mm / /8x / /4x / /4x / /8x / /8x / /2x / /2x / /4x / /4x Inch Standpipe R D Tube Part Hose-I.D. O.D. D Number DN Inch Size mm inch mm mm mm / / / / / / / / / / / / / / Not recommended for new construction. Instead use 06 or JC. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 20 Catalogue 4482-UK

296 Push-ok Hoses and fittings 0 - NPTF ale Pipe H H Part Hose-I.D. NTPF inch Number DN Inch Size mm thread mm mm (mm) / /8x / / /8x / C 6 / /8x / / /4x / / /4x / C 6 / /4x / S 6 / /4x / /8x / / /8x / C 6 / /8x / / /2x / / /8x / / /4x / / /4x / / /8x / / /8x / C 0 3/ /8x / / /2x / / /2x / / /4x / / /8x / / /8x / / /2x / / /2x / C 2 / /2x / / /4x / / /4x / / /2x / / /2x / / /4x / / /2x / / /2x / / /4x / / /4x /6 O aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel S = etric Hexagon For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 2 Catalogue 4482-UK

297 Push-ok Hoses and fittings 3 - NPTF Swivel ale Pipe H Part Hose-I.D. NTPF H Number DN Inch Size mm thread mm mm inch / /4x / / /8x / / /2x / / /4x /4 Note: This fitting allows for minor movement under pressure to relieve the torsion on hose, but it is not to be used for continuous or extreme swivelin Note: O-ring is not compatible with Phosphate Ester Fluids NPTF Female Pipe H H Part Hose-I.D. NTPF inch Number DN Inch Size mm thread mm mm (mm) / /4x / / /8x / C-S 0 3/ /8x / /2x / JIC 37 ale H Part Hose-I.D. UNF H Number DN Inch Size mm thread mm mm inch / /6x / / /6x / C 6 / /6x / / /2x / / /2x / / /6x / / /6x / / /4x / / /4x / / /6x / / /6x / C 20 3/ /6x /8 O aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel S = etric Hexagon For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 22 Catalogue 4482-UK

298 Push-ok Hoses and fittings 06/68 - Swivel Female - 06 JIC JIC - 37 and SE - 45 W W Part Hose-I.D. UNF inch Number DN Inch Size mm thread mm mm (mm) /4-4 6,3 7/6x / /4-4 6,3 7/6x / C 6 /4-4 6,3 7/6x / /4-4 6,3 /2x / /4-4 6,3 /2x / /4-4 6,3 9/6x / /8-6 9,5 /2x / /8-6 9,5 9/6x / /8-6 9,5 9/6x / C 0 3/8-6 9,5 9/6x / /8-6 9,5 3/4x / S 0 3/8-6 9,5 3/4x C-S 0 3/8-6 9,5 3/4x /2-8 2,7 7/6x / /2-8 2,7 9/6x / /2-8 2,7 9/6x / /2-8 2,7 3/4x / /2-8 2,7 3/4x / C 2 /2-8 2,7 3/4x / /2-8 2,7 7/8x /2-8 2,7 -/6x / /2-8 2,7 -/6x / /8-0 5,9 3/4x / /8-0 5,9 7/8x /8-0 5,9 7/8x C-S 6 5/8-0 5,9 7/8x /4-2 9, -/6x / /4-2 9, -/6x / C 20 3/4-2 9, -/6x / /4-2 9, -3/6x / S 20 3/4-2 9, -3/6x and K parts have brass nipples and steel nuts JIC 37 Swivel Female 45 Elbow E W H Hose-I.D. Part UNF E W Number DN Inch Size mm thread mm mm mm mm /4-4 6,3 7/6x / /8-6 9,5 9/6x / /2-8 2,7 3/4x /8 aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel S = etric Hexagon O For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 23 Catalogue 4482-UK

299 Push-ok Hoses and fittings 39 - JIC 37 Swivel Female 90 Elbow (Short) E W H W Part Hose-I.D. UNF E inch Number DN Inch Size mm thread mm mm mm (mm) / /6x / / /6x / C-S 0 3/ /6x / /4x / / /8x / /6x /4 4 - JIC 37 Swivel Female 90 Elbow (Extra ong) E Hose-I.D. Part UNF E W Number DN Inch Size mm thread mm mm mm mm H / /6x / /6x W 08 - SE 45 Swivel Female W Part Hose-I.D. UNF W Number DN Inch Size mm thread mm mm inch / /6x / / /6x / / /2x / / /2x / / /8x / / /8x / / /4x / / /8x / / /4x / / /4x / / /8x / /8x / /8x / /6x / / /6x /4 and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel C = Stainless Steel S = etric Hexagon = rass For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 24 Catalogue 4482-UK

300 77 - SE 45 Swivel Female 45 Elbow Push-ok Hoses and fittings E W H Hose-I.D. Part UNF E W Number DN Inch Size mm thread mm mm mm mm / /6x / / /8x / / /4x / SE 45 Swivel Female 90 Elbow E W H Hose-I.D. Part UNF E W Number DN Inch Size mm thread mm mm mm mm / /6x / / /8x / / /4x /8 JC - ORFS Swivel Female (Short) W H H W Part Hose-I.D. UNF inch inch Number DN Inch Size mm thread mm mm mm mm 3JC / /6x /6 /6 3JC / /6x /6 3/6 3JC S 0 3/ /6x JC / /6x /6 5/6 3JC / /6x /6 5/6 3JC / /6x /4 5/6 3JC / x /6 -/8 3JC / x /8 3JC / /6x /8-3/8 O aterial: without suffix = zinc plated - yellow chromated mild steel S = etric Hexagon For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 25 Catalogue 4482-UK

301 Push-ok Hoses and fittings J7 - ORFS Swivel Female 45 Elbow E W H Part Hose-I.D. UNF E W Number DN Inch Size mm thread mm mm mm inch 3J / /6x /6 3J / /6x /6 3J / /6x /6 3J / /6x /6 3J / x /8 3J / /6x /8 J9 - ORFS Swivel Female 90 Elbow E W H Part Hose-I.D. UNF E W Number DN Inch Size mm thread mm mm mm inch 3J / /6x /6 3J / /6x /6 3J / /6x /6 3J / /6x /6 3J / /6x /6 3J / x /8 3J / /6x /8 J - ORFS Swivel Female 90 Elbow (Extra ong) E H Part Hose-I.D. UNF E W Number DN Inch Size mm thread mm mm mm inch 3J / /6x /6 3J / /6x /6 3J / /6x /6 W J - ORFS ale Part Hose-I.D. UNF H Number DN Inch Size mm thread mm mm inch 3J / /6x /6 3J / /6x /8 O H J fittings are supplied without O-Rin For fittings with O-Ring please replace J by J0. Fittings with standard O-Ring seals can be used for temperatures from -30 C up to +05 C. Find O-Rings in section I. Special O-Rings are available on request. For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 26 Catalogue 4482-UK

302 F - French Compression Swivel Female Push-ok Hoses and fittings W Tube Part Hose-I.D. Thread O.D. W Number DN Inch Size mm metric mm mm mm mm 3F / x F / x F / x F / x F / x F / x F / x F / x F / x F x F K x and K parts have brass nipples and steel nuts. FF - etru-ok Swivel Female W Tube Part Hose-I.D. Thread O.D. W Number DN Inch Size mm metric mm mm mm mm 3FF / x FF / x FF / x FF / x FF / x FF / x FF / x FF / x and K parts have brass nipples and steel nuts. O aterial: without suffix = zinc plated - yellow chromated mild steel = rass K = rass without plastic ring For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 27 Catalogue 4482-UK

303 Push-ok Hoses and fittings 49 - anjo Union DIN 7642 D Diameter Part Hose-I.D. D Number DN Inch Size mm mm mm mm / / / / / / / C 0 3/ / / C 0 3/ / / / / / Find banjo bolts on page O29. DE - Double anjo Union D Diameter Part Hose-I.D. D Number DN Inch Size mm mm mm mm 3DE / DE / DE / DE / DE / DE / DE / Find banjo bolts on page O29. O aterial: without suffix = zinc plated - yellow chromated mild steel C = Stainless Steel For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 28 Catalogue 4482-UK

304 Push-ok Hoses and fittings /R - anjo olt (DIN 7643) H H G G I.D. G Part Number Part Number anjo Thread. Single Double H single double mm metric / inch mm mm mm x x R4 0 / x x R8 4 / R-08C / x R0 7 3/ x x R6 22 / x Push-ok Union Part Hose-I.D. Number DN Inch Size mm mm / / / / / / / Standard material: brass VW - Push-in Connector (VW standard 39-V-669) D aterial: without suffix = zinc plated - yellow chromated mild steel = rass K = rass without plastic ring C = Stainless steel K = Without plastic ring Tube Part Hose-I.D. O.D. D Number DN Inch Size mm mm mm mm 3VW82-6-4K 6 / VW82-8-4K 6 / VW82-8-4CK 6 / VW82-0-6K 0 3/ VW82-4-8K 2 / Standard material: brass O For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 29 Catalogue 4482-UK

305 Push-ok Hoses and fittings VW2 - SP Swivel Female (VW standard 39-V-663) D W Part Hose-I.D. SP D W Number DN Inch Size mm thread mm mm mm mm VW2-8937* 6 / /4x VW2-8938** 0 3/ /8x ,5 9 VW2-8939** 4 / /2x VW2-8940** 6 5/ /4x VW2-894** 20 3/ x *stainless steel nipple, steel nut **brass nipple, steel nut VW39D - Push-in Connector (VW standard 39D-40) Tube Part Hose-I.D. O.D. D Number DN Inch Size mm mm mm mm VW39D-40/C VW39D-40/2 3 / VW39D-40/3 5 3/ VW39D-40/4 6 / / H ale (Ford standard UWR ) W Part Hose-I.D. Thread W Number DN Inch Size mm metric mm mm mm H / x Standard material: brass H Female (Ford standard UWR ) Part Hose-I.D. Thread W Number DN Inch Size mm metric mm mm mm H /8-6 9,5 4x O W Standard material: brass aterial: without suffix = zinc plated - yellow chromated mild steel = rass C = Stainless Steel For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 30 Catalogue 4482-UK

306 Push-ok Hoses and fittings F - ale SP Parallel Pipe - Rigid - Straight (with O-ring Seal) Part Hose-I.D. SP H Number DN Inch Size mm thread mm mm inch 3F / /8x F / /4x F / /4x F / /8x F / /8x F / /2x F / /2x C3X8H22 - ale nipple 90 elbow (Ford standard UWR ) Part thread C N P Number inch metric mm mm mm mm 4-4C3X8H22 R /4 4x F3X83 - ale nipple straight fitting (Ford standard UWR ) Part thread C P Number inch metric mm mm mm 4-4F3X83 R /4 4x V3X8H7 - ale nipple 45 elbow (Ford standard UWR ) Part thread C N P Number inch metric mm mm mm mm 4-4V3X8H7 R/4 4x O aterial: without suffix = zinc plated - yellow chromated mild steel = rass For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 3 Catalogue 4482-UK

307 Push-ok Hoses and fittings 4-4C63X8H22 - ale swivel nut 90 elbow (Ford standard UWR ) Part thread C C N O P Number inch metric mm mm mm mm mm mm 4-4C63X8H22 R /4 4x F63X832 - ale swivel nut straight fitting (Ford standard UWR ) Part thread C C O P Number inch metric mm mm mm mm mm 4-4F63X832 R /4 4x V63X8H7 - ale swivel nut 45 elbow (Ford standard UWR ) Part thread C C N O P Number inch metric mm mm mm mm mm mm 4-4V63X8H7 R /4 4x O For hose types: 80 / 804 / 82 / 82FR / 83 / 836 / 837 Only items priced in current price list are carried in stock. Dimensions shown may be changed at any time without prior notice. O 32 Catalogue 4482-UK

308 Push-ok Hoses and fittings Push-ok Chemical Resistance edium I II III IV V STEE RSS SS cetic cid X X X (7) X X cetone X X X cetylene X X X X (2) ddinol okoplus HETG (4) F(4) ddinol okosynth HEES 46 F(4) F(4) EROSHE Turbine Oil 500 F(3) F X X gip rnica S46 (3) F(4) ir (,4) ir (dry) (3) F F X lcohol (ethanol-ethanol) F F F F F F mmonium Chloride X X X mmonium Hydroxide F F F F X mmonium Nitrate F F X mmonium Phosphate X X F mmonium Sulfate F X F myl lcohol X X X F F X nhydrous mmonia X X X X X X X X niline X X X F X nimal Fats F(3) F X F F (7) (7) ral Vitam EHF 46 (4) (4) romatic 00,50 F(3) F X - X sphalt X F X F X X (7) ST #3 Oil F F F F X TF- (3) F X utomotive rake Fluid X X X X - X X X via viacub synthofluid F(4) (4) via hydraulik bio (4) F(4) enzene, enzol X X X F X enzine X X X F X orax F(3) F F F F oric cid X X (7) P biohyd SE 46 (3) F(4) P energol HP-H 68 F X rayco 882 (3) X X rayco icronic 776RP (3) F F X rayco icronic 889 F(3) F X - X rine F F F X F (7) utane F(2) F X - X utyl lcohol, utanol F F F F F F F Calcium Chloride F F F X Calcium Hydroxide Calcium Hypochlorite X X X X (7) X Calibrating Fluid X Carbon Dioxide F(7) F F F (7) Carbon Disulfide X X X F X F Carbon onoxide (hot) F F F F (7) F (7) Carbon Tetrachloride X X X F X (7) (7) (7) Carbonic cid F F F X F X X F Castor Oil Castrol 5000 F(3) F X X Castrol iotec lpin 22 (3) (4) Celluguard - Chevron Clarity W 32, 46, 68 X Chevron FO-COO 80 F F F - X Chevron FR-8, 0, 3, 20 X X X X Chevron Hydraulic Oils W V 5, 32, 46, 68, 00 X Chevron HyJet IV (9) X X X X Citric cid (3) F X X (7) (7) Coolanol 5, 20, 25, 35, 45 Copper Chloride (3) F X X (7) X Copper Sulfate X X X (7) Cosmolubric HF-22, HF-30, HF-44 () () X X X Cottonseed Oil (3) F F X Crude Petroleum Oil (3) F X (7) (7) DE econa E46 (4) F(4) Deionized Water F F Dextron II TF (3) F X Diesel Fuel (3) X X Diester Fluids X X X F X Dow Corning DC 200, 50, 550, 560, FC26 F - Dow HD50-4 F F F Dowtherm,E X X X F X Dowtherm G X X X X X Elf hydrelf bio 46 (4) (4) Esso hydrauliköl HE 46 (4) F(4) Ethanol F F F F F F Ethers F - Ethyl cetate X X X F F F Ethyl lcohol F F F F F F Ethyl Cellulose F F F F F X F F Ethyl Chloride X X X X F F F Ethylene Dichloride X X X F X X X Ethylene Glycol (3) F F Exxon 30 FR X O O 33 Catalogue 4482-UK

309 Push-ok Hoses and fittings edium I II III IV V STEE RSS SS Exxon Esstic Exxon Nuto H 46, 68 X Exxon Tellura Indusrial Process Oils X Exxon Terresstic Exxon Turbo Oil 2380 (3) X F X Exxon Univolt 60, N6 (3) F X Finke aviaticon HY-HE 46 (3) (4) Formaldehyde X X X X F Formic cid X X X X X (7) X Fragol Hydraulic TR 46 (4) F(4) Fragol Hydraulik HE 46 (3) F(4) Freons see refrigerants Fuchs Plantosyn 3268 ECO F(4) F(4) Fuchs Plantosyn 3268 (3) (4) Fuel Oil (3) F X Fyre-Safe 20C,26,55,090E,50,220,300E X X X X Fyre-Safe 200C, 225, 2 (3) F Fyre-Safe W/O X Fyrguard 50, 50-, 200 Fyrquel 60, 90, 50, 220, 300, 550, 000 X X X X Fyrquel EHC, GT, T, VPF X X X X Fyrtek F, 25, 290, 295 X X X X X Gasoline (2,2) X X X X X Glue. F F F - X F Glycerine, Glycerol F Grease X Gulf-FR Fluid P37, P40, P43, P45, P48 X X X F H-55 (NTO) - X Halon 2, 30 F F F F - Helium Gas X X X X X Heptane F(3) F X X Hexane F(3) F X X Houghto-Safe 055, 0, 5, 20, 30 (9) X X X X Houghto-Safe 27 to 640 (3) F F Houghto-Safe 49R Deicer Fluid (3) - - Houghto-Safe 5046, 5046W, 5047-F X HP 00C (Jack hammer oil) (3) F X Hydrochloric cid X X X X X X (7) X Hydrofluoric cid X X X X X X (7) X Hydrogen Gas (2,5) X X X X X Hydrogen Peroxide X X X F X X X (7) Hydrogen Sulfide X X X X X X (7) Hydrolube F Hydrolubric 20-, 4, 595 (3) F F Hydrosafe Glycol 200 F HyJet IV (9) X X X X Isocyanates F(3) F F F X - Isooctane F(3) F X X Isopar H X X X X X Isopropyl lcohol F F F F F F JP3 and JP4 (3) X - X Kaeser 50P, 75P, 325R, 687R X X X F X Kerosene (2, 3, 5) (3) X F X acquer X X X F X X acquer Solvents X X X F X X actic cids X X X X X X (7) indol HF X X X F inseed Oil P-Gas (2) (2) (2) X X X agnesium Chloride X (7) X agnesium Hydroxide F F F F F F agnesium Sulfate F ercaptans X X X X X ethane (2,3) F F X ethanol F F F F F F ethyl lcohol F F F F F F ethyl Chloride X X X F X ethyl Ethyl Ketone (EK) X X X F X F ethyl Isopropyl-Ketone (5) X X X X X F I X X X X X X X X I-H-4670 F(3) F X F X I-H-5606 (3) F X I-H-6083 (3) F X I-H-7083 (3) F X I-H (3) F X I--204, 204 (3) F X I F(3) F X X I (3,6) F - X ine Guard FR - ineral Oil F X ineral Spirits (0) (0) (0) (0) X obil ero HFE (3) F F X obil DTE, 3, 5, 6, 8, 9 (3) F X obil DTE 22, 24, 25, 26 (3) F X obil E 224H (3) X X - obil E Syndraulik 46 F(4) (4) obil Glygoyle, 22, 30, 80 - X O O 34 Catalogue 4482-UK

310 Push-ok Hoses and fittings edium I II III IV V STEE RSS SS obil HF (3) F X obil Jet 2 F(3) X X X obil Nyvac 20, 30, 200, FR (3) F F obil Rarus 824, 826, 827 X X X F X obil SHC 600 Series (3) F X obil SHC 800 Series (3) F X obil SH 624 (3) - X obil Vactra Oil F X obil XR 68 X X X X obilfluid 423 (3) F X obilgear SHC 50, 220, 320, 460, 680 F(3) X F F X obilrama 525 F X olub-lloy 890 X X X F X oly ube HF 902 F(3) F F F X onolec 620 Hydraulic Oil X orpholine (pure additive) X X X X X X X Naptha F(3) F X X Napthalene X X X F X Natural Gas (2) (2) (2) X X X Nitric cid X X X X X X X (7) Nitrobenzene X X X F X X X (7) Nitrogen F() F() F() F() F() Nuto H 46, 68 X Nyvac 20, 30, 200, FR (3) F F Nyvac ight X X X - Oil Synthetic lends X X X X X Oxygen (2,5) X X X X X X Ozone F F F - Panolin HP synth 46 (3) (4) Perchloroethylene X X X X X F X Petroleum Ether F(3) F X F X Petroleum Oils X Phenol (Carbolic cid) X X X X X F Phosphate Ester lends X X X X X Phosphate Esters (9) X X X X Phosphoric cid X X X X X X X (7) Polyalkylene Glycol F F - X Polyol Ester () F X X X Potassium Chloride X F (7) Potassium Hydroxide X X X F (7) X Potassium Sulfate Propane (2) (2) X X X Propylene Glycol (3) F F F F Pydraul 60, 50, 625, F9 (9) X X X X Pydraul 90, 35, 230, 32, 540, C (9) X X X X F Pydraul -200 X X X F X Pyro Gard 43, 230, 630 (9) X X X F X Pyro Gard C, D, R, 40S, 40W (3) F F Pyro Guard 53, 55, 5, 42 (9) X X X X Quintolubric 700 F Quintolubric 822, 833 () () X X X Quintolubric 957, 958 (3) F F Refrigerant Freon 3, 4 (5) X X X X X Refrigerant Freon 2 (5) X X X X X Refrigerant Freon 22 (5) X X X X X Refrigerant Freon 502 (5) X X X X X Refrigerant HFC34 (5) X X X X X RTV Silicone dhesive Sealants (5) X X X X X Safco-Safe T0, T F F Safety-Kleen ISO 32, 46, 68 hydraulic oil (3) F - X Safety-Kleen Solvent (0) (0) (0) (0) X Santoflex 3 F F F - F Santosafe 300 X X X - X Santosafe W/G 5 to Sea Water F F F F X F (7) Sewage F(3) F F F (7) (7) (7) Shell 40 Solvent (0) (0) (0) (0) X Shell Clavus HFC 68 X X X X X Shell Comptella Oil F(3) F F X Shell Comptella Oil S 46, 68 F(3) F F X Shell Comptella Oil S F(3) F F X Shell Diala, (R) Oil X (3) F F X Shell FR X Shell IRUS 902, Shell naturelle HFE 46 F(4) (4) Shell Pella- X Shell Tellus (3) F X Shell Thermia Oil C X Shell Turbo R F(3) F X X SHF 220, 300, 450 () () X X X Silicate Esters F X Silicone Oils - - Skydrol 500-4, D-4 X X X X (8) Soap Solutions F(3) F X F Soda sh, Sodium Carbonate F Sodium isulfate F F F F F Sodium Chloride F F F X F O O 35 Catalogue 4482-UK

311 Push-ok Hoses and fittings edium I II III IV V STEE RSS SS Sodium Hydroxide X X X X Sodium Hypochlorite F F F X F X X X Sodium Nitrate F F F (7) Sodium Peroxide X X X X X X Sodium Silicate Sodium Sulfate Soybean Oil (3) F Steam X X X X X F Stoddard Solvent (0) (0) (0) (0) X Sulfur Chloride X X X F X (7) X (7) Sulfur Dioxide X X X X F X (7) F Sulfur Trioxide X X X F F X X X Sulfuric cid F(7) F F X F(7) (7) X (7) Tannic cid (3) F F X (7) X Tar X F F F X X (7) Tebiol Esterhyd HE 46 F(4) F(4) Tellus (Shell) (3) F X Texaco 760 Hydrafluid X Texaco 766, 763 ( ) F F Texaco -Z Oil F X Texaco Way ubricant 68 X Toluene, Toluol X X X F X Transmission Oil X Tribol 440 F(3) F X X X Trichloroethylene X X X F X X Trim-Sol (3) F F X Turpentine X X X F X Ucon Hydrolubes (3) F F Univis J26 - X Unleaded Gasoline (2,2) X X X X X Urea F F F F F - F Urethane Formulations - Varnish X X X F X F F Varsol F(3) F (0) (0) X Versilube F44, F Vinegar X X X F (7) X Volt Esso 35 X Water F F Water / Glycols (3) F Xylene, Xylol (5) X X X X X Zerol 50 X Zinc Chloride X X X F Zinc Sulfate X) X Resistant rating key: = Prefered F = Fair X = Unsuitable = No recommendation () Hose must be pin pricked (2) egal and insurance regulations must be considered (3) hoses in column 2 are recommended (4) aximum 58 F (70 C) (5) hose 235 and 285 are recommended for refrigerants (6) aximum 85 F (85 C) (7) Satisfactory at some concentrations and temperatures, unsatisfactory at others (8) Some discoloration of fluid may occur without damage to fluid properties (9) For phosphate ester fluids use Column V, 235, 285 hoses (0) cceptable for flushing hose assemblies () Use 38, 48, 772, or 83 (2) 22FR hose recommended (3) For dry air applications hoses from column 2, 4, 5 and 235 is recommended. (4) aximum 22 F (00 C) (5) hoses 235 and 285 are recommended Column I 80, 82, 82FR, 837, Column II 83 Column III 77C, 78C Column IV 206, 23, 266, 296, 636, 836 Column V 804 O Hose selection by medium and hose type This hose compatibility chart is a ready reference of Parker hose adaptability with various media. It is intended as a guide to chemical compatibility with the internal fluid and assembly lubricant applied internally. While all listings shown reflect known usage or authoritative sources, other factors may in some cases render them invalid. Final hose selection depends also upon pressure, fluid temperature, ambient temperature, and special requirements or variations which may not be known by Parker Hannifin. egal and other regulations applicable to footnotes (2), (3) and (4) must be followed with particular care. Where an external compatibility problem may occur or for fluids not listed, contact your Parker Hannifin field representative. O 36 Catalogue 4482-UK

312 Thermoplastic single tubes and Pneumo-Tube bundles Catalogue 520-UK

313 Thermoplastic single tubes and Pneumo-Tube bundles Index Pages Thermoplastic single tubes and Pneumo-Tube bundles P 3 Polyamide tubing P 4-P 5 Polyurethane tubing P 6-P 7 Ordering information P 8 Technical tube preparation P 8 Tube bundles P 9-P0 Singleline Pneumotube P P P 2 Catalogue 520-UK

314 Thermoplastic single tubes and Pneumo-Tube bundles Principle ll Parker tubes are manufactured to international standards and are fully compatible with Parker s wide range of push-in, compression and screw type tube fittings, for example Parflex thermoplastic fittings such as Fast & Tite, TrueSeal T, Par-arb and ini-arb as well as components from the Parker Pneumatic Connectors Handbook. Standard packaging of all Parker single tube products is polyethylene bags. Dispensing cardboard boxes (K) are available on request. pplications Pneumatics edical applications ubrication systems Food and beverage applications Process control lines Fluid applications Instrumentation and control Robotics systems Pressurised air tools Paint systems utomation systems P P 3 Catalogue 520-UK

315 Thermoplastic single tubes and Pneumo-Tube bundles Parker calibrated polyamide tubing Parker calibrated polyamide tubing is extruded in polyamide (P/2) for use with pneumatic fittings. This is manufactured within the limits of DIN 73378, S 5409 PT and CETOP RP54 P recommendations, and is ideal for pneumatic applications. For continuous use at high temperature we recommend tube which is protected against heat and light. dvantages - Good vibration/damping properties, - High abrasion resistance - Tubing available in several colours for easy - ow pressure drop, identification - No thermal expansion Technical features Working pressure (bar) C Tube size N3 x N4 x N4 x N5 x N6 x N8 x N0 x N0 x N0 x N2 x N4 x N6 x Working pressure of polyamide tubing is dependant on the operating temperature. Working pressures shown are based on a design factor of 3: P P 4 Catalogue 520-UK

316 Thermoplastic single tubes and Pneumo-Tube bundles Parker calibrated polyamide tubing Tube bend radius To ensure the correct functioning of both tube fitting and pneumatic system it is important not to exceed the minimum bend radius of the tube. Tube inimum size bend radius (mm) 3 x x x 20 5 x 35 6 x 35 8 x 45 0 x x 60 2 x 70 4 x x Tube outside diameter tolerances Tube OD Tolerance mm 3 to 5 mm to 6 mm Chemical compatibility Parker polyamide tubing is suitable for use with a wide variety of fluids. The table below shows typical fluids used with polyamide tubin Working temperature Fluid -20 C +20 C +60 C Cutting oil Cutting fluids Water Hydraulic oils ineral oils / greases Carbon dioxide cetone Gasoline Trichloroethylene - C C = excellent, = medium, C = poor For other fluids please contact us Colours and sizes available For identification purposes Parker can supply on request, tubes in several colours : red, blue, green, yellow and black. Parker tubing is packaged and delivered as standard in 00 metre lengths for sizes 3 x 0.65 to 2 x and in 25 metre lengths for larger sizes. Tube size (mm) Tube Part number ength OD ID Wall Thickness (m) Natural () Red (2) lue (3) Green (4) lack (5) Yellow (7) N3x0.65/-00 N3x0.65/2-00 N3x0.65/3-00 N3x0.65/4-00 N3x0.65/5-00 N3x0.65/ N4x0.65/-00 N4x0.65/2-00 N4x0.65/3-00 N4x0.65/4-00 N4x0.65/5-00 N4x0.65/ N4x/-00 N4x/2-00 N4x/3-00 N4x/4-00 N4x/5-00 N4x/ N5x/ N6x/-00 N6x/2-00 N6x/3-00 N6x/4-00 N6x/5-00 N6x/ N8x/-00 N8x/2-00 N8x/3-00 N8x/4-00 N8x/5-00 N8x/ N0x.25/-00 N0x.25/2-00 N0x.25/3-00 N0x.25/4-00 N0x.25/5-00 N0x.25/ N0x/-00 N0x/2-00 N0x/3-00 N0x/4-00 N0x/5-00 N0x/ N2x/-00 N2x/2-00 N2x/3-00 N2x/4-00 N2x/5-00 N2x/ N4x.5/-25 N4x.5/2-25 N4x.5/3-25 N4x.5/4-25 N4x.5/5-25 N4x.5/ N6x.5/-25 N6x.5/2-25 N6x.5/3-25 N6x.5/4-25 N6x.5/5-25 N6x.5/7-25 P P 5 Catalogue 520-UK

317 Thermoplastic single tubes and Pneumo-Tube bundles Parker calibrated polyurethane tubing Parker calibrated polyurethane tubing is obtained by extrusion. The material hardness is 52 Shore D. Its very high flexibility allows a small minimum bend radius for compact installations. dimensional inspection system based on advanced laser technology maintains a tight tolerance on the outside tube diameter. This is manufactured within the limits of NF E recommendations. dvantages - Extreme flexibility with bend radii up to three times - Good vibration resistance, better than polyamide tubing allows compact installations - ight weight, - Tube available in several colours for line identification, - Reduced fitting time. Technical features Working pressure (bar) C Tube size TPU 3 x TPU 4 x TPU 6 x TPU 8 x TPU 0 x TPU 2 x TPU 6 x Working pressure of polyurethane tubing is dependant on the operating temperature. Working pressures shown are based on a design factor of 3: P P 6 Catalogue 520-UK

318 Thermoplastic single tubes and Pneumo-Tube bundles Parker calibrated polyurethane tubing Tube bend radius To ensure the correct functioning of both tube fitting and pneumatic system it is important not to exceed the minimum bend radius of the tube. Tube size inimum bend radius (mm) 3 x x x 22 6 x 27 8 x x x 2 62 Polyurethane tubing outside diameter tolerances Tube OD Tolerance mm 3 to 8 mm ± 0. 0 and 2 mm ± 0.5 Chemical compatibility Parker polyurethane tubing is suitable for use with a wide variety of fluids. The table below shows typical fluids used with polyurethane tubin Working temperature Fluid -20 C +20 C +60 C Cutting oil Cutting fluids Water Hydraulic oils ineral oils / greases Carbon dioxide Gasoline Trichloroethylene - C C cetone - C C = excellent, = medium, C = poor For other fluids please contact us Colours and sizes available For identification purposes Parker polyurethane tubing is available in three colours : blue, black and silver. Parker calibrated polyurethane tubing is packaged and delivered in 00 meter lengths as standard. Tube size (mm) Tube ength Part number OD ID Wall Thickness (m) lue (3) lack (5) Silver (3) TPU3x0.5/3-00 TPU3x0.5/5-00 TPU3x0.5/ TPU4x0.75/3-00 TPU4x0.75/5-00 TPU4x0.75/ TPU5x/3-00 TPU5x/5-00 TPU5x/ TPU6x/3-00 TPU6x/5-00 TPU6x/ TPU8x.25/3-00 TPU8x.25/5-00 TPU8x.25/ TPU0x.5/3-00 TPU0x.5/5-00 TPU0x.5/ TPU2x2/3-00 TPU2x2/5-00 TPU2x2/3-00 lso available as twin line tubes in black/blue or silver/silver. Deviating constructions also possible. For other tube sizes, colours and lengths please contact us. P P 7 Catalogue 520-UK

319 Thermoplastic single tubes and Pneumo-Tube bundles Ordering information Ordering key Examples: N 6X/5-50 K Cardboard packaging ength in m Colour: black Wall thickness in mm Outer diameter in mm Polyamide 2X022/-00 ength in m Colour: natural Polyethylene Wall thickness in inches Outer diameter in inches Colour codes: Natural Red 2 lue 3 Green 4 lack 5 rown 6 Yellow 7 Orange 8 Grey 9 Purple 0 Pink White 2 Silver 3 Technical tube preparation lways use a Parker tube cutter to cut technical tubing lways ensure that the tube is out square before assembling it to the fittin P P 8 Catalogue 520-UK

320 Thermoplastic single tubes and Pneumo-Tube bundles Tube bundles - For maximum safety and minimum installation work Stranded inner tubes for maximum flexibility PVC coat for protection against damage Colour-coded inner tubes for easier identification Polyester ribbon to ensure a smooth outer cover Parker Pneumo-Tube bundles are a high-quality thermoplastic product designed especially for process control and monitoring applications. Parker Pneumo-Tube bundles are excellent for use in hydraulic and pneumatic systems. The PVC coat protects the product against mechanical and chemical damage. Each tube can be easily and quickly identified by its colour and position within the stranded bundle. The single tubes are marked in intervals of max. 500 mm as a standard. Using a combination of colours, tube and sheath materials, together with various barrier types, Pneumo-Tube can be constructed to meet the most varied and demanding applications. Electrical wires and tension members can also be incorporated. Standard configurations are available in long continuous lengths P P 9 Catalogue 520-UK

321 Thermoplastic single tubes and Pneumo-Tube bundles Tube bundles types STS Type Tube bundle PVC standard thickness sheathed for protection against damage ETS Type Tube bundle with extra thick PVC, sheathed for direct underground burial with sand cushion. ST Type Tube bundle, PVC sheathed, with two-layered hoop-steel armouring for direct underground burial without special beddin ST Type Tube bundle PVC sheathed, with thermal barrier for short-term resistance to fire. DT Type Tube bundle, PVC sheathed with double thermal barrier for extra fire protection. H Type P Tube bundle, PVC sheathed with central air supply line. P 0 Catalogue 520-UK

322 Thermoplastic single tubes and Pneumo-Tube bundles Prestoweld 2 tubing Prestoweld 2 thermoplastic tubing has been specifically designed to meet the stringent requirements of the robotic welding industry for pneumatic control. The combination of the Prestoweld 2 tubing and instant fittings ensures a cost and time saving during the assembly. y using weld spark resistant material, Prestoweld 2 guarantees a high quality, reliable and long lasting solution for the air and water supply of welding robots. Prestoweld 2 single tube is tested and approved by the major players in the automotive industry. D D Technical features aterial: Tubing colour: randing colour: Working temperature: Fittings: Weld spark resistant Polyurethane, halogen-free. lack. White (other colours on request) C up to + 90 C. Prestoweld 2 instant fittings (see section E). dvantages Weld sparks resistant materials - No protective cover required. - No need for tube preparation. - No additional assembly tool required. - Simple, fast and reliable assembly. - ong service life. Silicon and labs free tubing - Free of all paint effective substances. - Does not interfere with the coating quality (imperative in the automobile industry). Colour coding possible - Identification of circuits. - Prevents mix-up of tube functions. Small bend redius and small overall dimensions - Flexibility. - Easy assembly even with limited space. D D Part number ax. working pressure ax. burst pressure in. bend radius Weight (mm) (mm) at 23 C (bar) (bar) (mm) (/m) 2 4 PWPU 4x PWPU 6x PWPU 8x PWPU 8x PWPU 0x PWPU 2x PWPU 4x P P Catalogue 520-UK

323 ccessories Catalogue 0026-UK

324 ccessories Index Pages ccessories anual copper tube bender Q Copper tube cutter Q 3 Par-ok - Snap-action ratchet spanner Q 3 PTC - Plastic tube cutter Q 4 Parker Teflon tape Q 4 SVGP - Slide valves Q 4 Complementary products Stainless steel clamps Q rass tube fittings Q Prestomatic Q 5 Q Q 2 Catalogue 0026-UK

325 ccessories anual copper tube bender Tube size Part number Radius ength Weight mm mm mm 6x 2000/ x 2000/ x 2000/ x 2000/ x 2000/ x 2000/ Copper tube cutter djustable cutting tool. Capacity : copper tube from 6x to 22x.5 mm Part number : 2005 Par-ok - Snap-action ratchet spanner etric sizes Inch sizes Hex Part number Hex Part number C Weight mm in. mm mm mm / / / / / / / / / / / Full kit of 0 sizes : kit For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. Q Q 3 Catalogue 0026-UK

326 ccessories PTC - Plastic tube cutter Cutting tool. Capacity : plastic tube up to 4 mm O.D.. Part number : PTC Replacement blade for plastic tube cutter Part number : PTC00R Parker Teflon tape Improves sealing on threads. Resists most known chemical agents. High pressures and temperatures (250 C). vailable in 2 metre reels mm x 0.08 mm section. Part number : Ruban Teflon SVGP-Slide valves E C Part number C E Weight G /8 SVG4-/8P G /4 SVG4-/4P G 3/8 SVG4-3/8P G /2 SVG4-/2P For product availability please consult our price list 0093-UK. Dimensions shown may be changed at any time without prior notice. Q Q 4 Catalogue 0026-UK

327 Complementary ccessories products The Parker Fluid Connectors Group has a complete range of components for pneumatic systems. The major product features are shown. For detailed information please consult the corresponding product catalogue. Stainless steel clamps - catalogue 8000 Hose Clamps High quality worm drive clamps with slotted hexagon head screws. aterials : stainless steel housing and hexagon head screws of ISI 30 stainless steel Working pressure : according to size from 70 to 000 psi (5 to 70 bar) Standards : SE J 536 (DIN 30 7 heavy duty series) Standard range : 0.25" to 7" (6 to 78 mm) rass tube fittings - catalogue 350 Comprehensive range of brass tube fittings for use with imperial rigid or plastic tubing to NPT threads. Prestomatic - bulletin Comprehensive range of metric push-in air brake fittings for the truck, bus and trailer industries. Q Q 5 Catalogue 0026-UK

328 Index Part number Page Part number Page 2000 Q Q 3 207CH J 9 207P J 8 209P J 7 26P J 5 28P J 29P J 2 222P J O O O O O O O O O O O O O O O O 8 3D82 O 5 35C82 O 5 36C82 O 6 37C82 O O 2 39C82 O 2 3F82 (new) O O O 9 3C082 O 4 3C382 O 0 3C482 O 3C582 O 3C82 O 3 3CE82 O 3 3CF82 O 4 3D082 O 4 3D982 O 9 3DE82 O 28 3F82 O 27 3FF82 O 27 3J82 O 26 3J782 O 26 3J982 O 26 3JC82 O 25 3J82 O 26 3VW82 O O O 6 82 O 7 82FR O 7 83 O O O 9 /R O 29 G34 N 24 G44 N 24 G 4 PK 9 P H 0 T G 4 VG4POCK VGC 5 VG 7 VGTC 5 VGT 7 C 8 C3 G 9 C3P H 8 C3P D 9 C4P H 8 C4UCO (new) K 6 C63P D 9 C63PK 8 C63PK C 9 C63P D 0 C63PK 8 C63PK C 9 C63SPK 8 C64PK C 9 C64P D 0 C64PK 9 C64PK C 0 C64PW E 5 C64SP D 0 C64SPK 9 C68PK C 0 C68P D C68PK 9 C68PK C 0 C68SP D C68SPK 9 C6P D 9 C8 G 9 C8P H 9 C G 9 CP H 8 CD43 J 9 CD43 Clip F 3 C4UC0 (new) K 5 C4UD4 (new) K 5 COR4 G 2 COR4P H 0 COR4P D 4 COR4PD D 5 COR8P D 4 COR8PD D 5 COR8P C 5 CORP D 4 CORPD D 4 CR33 DD44 J 9 DD44 DD44KT DP O 7 DR O 8 DS O 8 E I 39 E G 0 EG K 8 -O6 Catalogue 0093-UK

329 Index Part number Page Part number Page EG O 6 E I 9 EP D EPK 0 EPFK C EPK C 0 EPW E 6 ET I 8 EV K 8 EV O 7 EW I 7 EW K 8 EW O 7 F23P D 6 F23P C 7 F28P D 6 F28P C 7 F3 G 6 F3P H 6 F3H 6 F3P 6 F3P D 6 F3P C 7 F4H 7 F4 G 6 F4P H 7 F4P 6 F4P D 7 F4P C 7 F4PW E 4 F4UCO (new) K 5 F4UF4U (new) K 7 F4UG4 (new) K 7 F8 G 7 F8P H 7 F8P 7 F8P D 7 F8P C 8 F8PW E 4 F G 6 FP H 6 FF J 5 FF33 J 5 FF33 6 FF4G4 8 FF44 J 5 FF44 6 FF633 7 FF84 7 FF88 7 FG J 6 FG43 J 6 FG43 7 FG44 8 FG48 8 FGH 6 FHG4 J 2 F I FN4 5 FN G 4 FNP D 6 FNP E 6 FNPK 9 FNPK C 5 FP D 6 G I 7 G4 G 8 G4P 7 G4P D 8 G4P C 8 G8P C 8 G G 7 GE--ED I 2-3 GE-R-ED I 0- GE-UNF/UN I 4-5 GG J 8 GG44 J 8 GG44 0 GG84 0 GG88 9 G I 36 H O 30 H O 30 H G 7 HP H 7 HHP J 2 HHP3 J HHP3 5 HP J HP3 J HP D 8 HPK 7 HPK C 8 HPW E 4 HS3PK 6 J3PK 6 J5PK 7 J663PK 7 J664PK 7 J6PK 7 J G 0 JP H 9 JP D 2 JPK 0- JPFK C JPK C K G 2 KOO4 J 0 KOO4 3 KRO KRRS3 4 EE - UNF I 30 EE- I 26 EE-R I C3 K 9 4-4C63 K 0 4-4F3 K 9 4-4F63 K 0 4-4V3 K 9 4-4V63 K 0 NI 7 NI2 8 NIF 7 VG 9 -DPR-D I O444 J 0 Catalogue 0093-UK

330 Index Part number Page Part number Page O444 2 S443 J 0 S443 2 RO434 J 0 RO434 3 RS433 2 P40N 5 P4UN 4 P80N 5 Parker Teflon tape Q 4 Par-ok Q 3 P2E N 6 P2F3C N 6 P2G4Z N 6 P2P N 6 P3E N 6 P3F3C N 6 P3G4Z N 6 P3P N 6 P4E N 6 P4F3C N 6 P4G4Z N 6 P4P N 6 P52E N 5 P52F3C N 5 P52G4Z N 5 P53F3C N 5 P53G4Z N 5 P54F3C N 5 P54G4Z N 5 PF52E N 8 PF52F3C N 8 PF52G4Z N 8 PS25F (new) N 0 PS25H (new) N 0 PS25 (new) N 0 PS37F (new) N 0 PS37H (new) N 0 PS37 (new) N 0 PS50F (new) N 0 PS50H (new) N 0 PS50 (new) N 0 PS502F (new) N PS502H (new) N PS502T (new) N PCF2E N 22 PCF2F3C N 22 PCF2G4Z N 22 PCF52E N 2 PCF52F3C N 2 PCF52G4Z N 2 PCV4 F 27 PCV4PK F 27 PE2E N 4 PE2F3C N 4 PE2G4Z N 4 PE2P N 4 PE52E N 3 PE52F3C N 3 PE52G4Z N 3 PEF2E N 7 PEF2F3C N 7 PEF2G4Z N 7 PEF2P N 7 PEF3E N 7 PEF3F3C N 7 PEF3G4Z N 7 PEF3P N 7 PEF52E N 6 PEF52F3C N 6 PEF52G4Z N 6 PEF53E N 6 PEF53F3C N 6 PEF53G4Z N 6 PES25F (new) N 9 PES25H (new) N 9 PES25 (neu) N 9 PGauge F 3 PIV4 F 27 PIV4PK F 27 Pneumo-Tube P 3 PN G 5 Polyamide tubing P 4-5 Polyurethane tubing P 6-7 PR4 F 29 Prestoweld 2 tubing P PRI4 F 29 PRIP F 29 PR4P F 29 PRS F 30 PTC Q 4 PTF4 F 9 PTF4E6P F PTF4P F 9 PTF4PW F 0 PTF8E6P F PTF8P F 9 PTF4P F 9 PTF8P F 9 PTFC4PK (new) F 6 PTFC8PK (new) F 6 PTF8 F 3 PTF8P F 2 PTF8PK (new) F 7 PTFC4PK (new) F 6 PTFC8PK (new) F 6 PTFIPK F 5 PTFIWPK F 5 PTF4 F 3 PTF4CO F 3 PTF4P F 3 PTF8 F 3 PTF8P F 3 PTFC4PK (new) F 7 PTFCKPK (new) F 6 PTF8PK (new) F 7 PTFIPK F 5 PTP4 F 25 PTP4P F 24 PTP8 F 25 PTP8P F 24 PTR J 7 PTR34 J 6 PTR34 8 PTR44 9 PTR44H 9 Catalogue 0093-UK

331 Index Part number Page Part number Page PTR48 9 PW (new) F 3 PW- F 9 PWE- F 2 PWPU (new) P PWR-H F 23 PWR-HE F 23 PWS- F 25 PWS-E F 25 PWS- F 25 R3 G R3P H 9 R63P D 2 R63PK R63PK C 2 R64P D 2 R64PK R64PK C 2 R68P D 3 R68PK 2 R68PK C 2 Ratchet F 3 R G 0 RP H 9 RRD 8 RRO334 3 RRP 8 RRS333 2 S3 G S3P H 0 S4UCO (new) K 6 S63P D 3 S63PK 3 S63PK C 2 S64P D 3 S64PK 3 S64PK C 3 S68P D 3 S68PK 3 S68PK C 3 S G SP H 0 SC4U D 5 SC4UD D 5 SC8U D 5 SC8UD D 5 SC-50 I Splug F 3 SV I 6 SVGP Q 4 T I 9 T23FPK 9 T23FP C 6 T23HF G 3 T23HFP D 6 T23U G 5 T24FPK 9 T24FP C 6 T24HG G 4 T28FPK 20 T28FP C 6 T28HF G 3 T2ESPK 0 T2ESPK C T2HF G 2 T2HG G 3 T2JJPK 2 T2JPK 2 TEE - UNF I 29 TEE- I 25 TEE-R I 2 TEP D 6 TE2PK C 5 Thermoplastic tube P 3 T G 5 TR2PK 20 TR2PK C 6 TR G 5 TRP D 6 TRPW E 6 TS2PK 20 Single tube and bundles P 9-0 VEE-UNF I 3 VEE- I 27 VEE-R I 23 VK I 37 VSTI-R/-ED I 38 VW2 O 30 VW39D (new) O 30 W I 8 W G 8 WP D 8 WP G 8 WP H 7 WE6P D WE6PK 0 WEE- I 24 WEE-R I 20 WEE-UNF I 28 WGG44 0 WG4P D 8 WGG44 J 9 WP D 9 WP C 9 WPW E 5 WYJ6PK 4 YGX/X-82 (new) K 6 YGX/XCO (new) K 7 YJ2PK 4 YJ2PK C 4 YJ52PK 5 YJ563PK 5 YJ564PK 5 YJ5PK 4 YJ63PK 5 YJ63PK C 4 YJ64PK 6 YJ68PK C 5 YJPK 4 YJPFK C 4 YJPK C 3 Y444 4 YS443 4 Catalogue 0093-UK

332 Parker Hannifin Corporation bout Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over,400 product lines that control motion in some,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. Parker s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. ore specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information Customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Centre. The Centre can be called toll free from France, Germany, ustria, Switzerland or the United Kingdom. You will be answered by a Parker employee in your own language. Call Freephone: (00800 C PRKER). The erospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets system-control and fluidhandling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The utomation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.