Custom-Orthotics Solutions and Equipment

Transcription

1 Custom-Orthotics Solutions and Equipment

2

3 Custom-Orthotics Solutions and Equipment Custom-Orthotics Ottobock

4

5 Table of Contents About this catalogue AFO system joints 8. Selection guide AFO Conventional ankle joints.... System components.... Prefabricated AFO's... 7 KAFO system joints. Selection guide KAFO.... Locked joints Free motion system joints SCO system joints Waterproof orthoses Correction system joints... 8 Materials and accessoires 86. Bars and stirrups Equipment Materials Thermoplastics Carbon materials Resin Custom-Orthotics Ottobock

6 About this catalogue Orthotics in general Orthotics in general Global networking has also asserted itself in the medical technology sector. In order to work with the same terminology internationally, the abbreviations of the English terms for the different types of orthoses are used. HO HKAFO These are already used in many countries in the corresponding fitting or device lists. Only the abbreviations common for lower limb orthoses are shown in the overview here, but these are widely used for the entire locomotor system. Lower limb orthosis types KO AFO FO KAFO HO HKAFO KAFO KO AFO FO Hip orthosis Hip orthosis Hip-knee-ankle-foot orthosis Complete leg orthosis encompassing the hip, reciprocal gait orthosis (RGO) Knee-ankle-foot orthosis Complete leg orthosis Knee orthosis Knee orthosis Ankle-foot orthosis Lower leg orthosis Foot orthosis Foot orthosis Muscle strength assessment according to Janda Hip extensor 5 Knee flexor 0 Hip flexor 5 Knee extensor 5 0 No visible and/or palpable muscle contraction Visible and/or palpable muscle contraction with no motoric effect Distinct muscle contraction, movement with cancelling of gravity possible Movement against gravity possible Movement against low to medium resistance possible 5 Movement with normal strength Foot extensor 0 Dorsal flexor 0 Ottobock Custom-Orthotics

7 Table of Contents Ottobock For Material Colour For Width Colour About this catalogue Searching, finding and ordering Searching, finding and ordering This catalogue is organised into Sections. About this catalogue AFO System joints 8. Selection Guide AFO Conventional Ankle Joints.... System components... Tabs on the right-hand page margins as well as the subtitles (e.g. KAFO/KO) at the top of every page also serve as quick and easy reference guides.. Prefabricated AFO'S... 6 KAFO System Joints 0. Selection Guide KAFO.... Locked joints Free motion System joints SCO System joints Waterproof Orthoses Correction system joints Materials and Accessoires 8. Splints/splint accessories Equipement Materials KAFO System Joints SCO System joints. Thermoplastic Carbon Resin Z hook-and-loop strap 70Z= K=80/=0 Polyamide skin colour 70Z= K=80/=0 Polyamide black 70Z= K=80/=0 Polyamide skin colour 70Z= K=80/=0 Polyamide black 70D Y-hook-and-loop 70D=8-0 70K=80/=0 8 mm skin colour 70D=8-7 70K=80/=0 8 mm black List of Key Words control electronics 7 correction system joints 78, 80 Countersunk head screw, 55 7LK unilateral knee joint 5 A D adapter Decision-making sleeve 89 aid 6 adjustable ankle joint with universal 67 f drilling template 69 foot part dummy for knee joint 7 Index adjustment adapter 88 dynamic unit for correction system 79 alignment axis 88 joint NoE Allen screw with collar 88 Article/Reference Page Article/Reference No Page Article/Reference No Page 89 Allen wrench 7B07 7M 5 aluminium threaded jaws 70 E-MAG Active 6, 7, ankle and knee support E-MAG Active knee 7B08 joint 67 7MS0 7 ankle foot orthosis 7 electronics cable 7 5, 55 A0 7B 7PA 75, 76 7PF 75 7B -0 7B5 7PK 9, 5, 75, 77 The list of keywords lists all products in alphabetical order. Alternatively, the index lets you find the page numbers for products by reference number. 7B 59 7B 85 7B5 85 7B6 85 7B7 85 7B6 7B0N 7, 7 7B05 7 7BK 78, 80, 8 7BK 79 7PK-WR 75 7U8 58 7U9 58 7U 80 7X8 57 Service Fabrication Customized Solutions Ottobock Service Fabrication offers custom orthotics products and services. These are listed in the catalogue 66K7=EN. Service Fertigung Lösungen nach Maß Materials Components and Systems For more information or to place orders for products in the materials and tools category, please use the 66K Ottobock materials catalogue or 66K0 for Planning and Equipping. Custom-Orthotics Ottobock 5

8 About this catalogue Searching, finding and ordering Name of product Searching, finding and ordering Illustration of product Name of product Illustration of product 7M multifunction system ankle joint For integration in ankle foot orthoses with dorsal, plantar limitation or spring assist, incl. parallel alignment aid Gesamtlänge Max. lower Max. body Material Oberteil Fußbügel leg length weight 7M multifunction system ankle joint 7M= 0 mm 550 mm 00 kg Stainless steel Set For integration in ankle foot orthoses with dorsal, plantar limitation or spring assist, 7M= 9 mm 50 mm 5 kg Stainless steel Set incl. parallel alignment aid Scope of delivery see illustration Brief product description ICONS for Brief guidance product description ICONS for guidance Notice Available information material Available information material Replacement parts graphic Replacement parts graphic 67G66 67G66 Gesamtlänge Max. lower Max. body Material Oberteil Fußbügel leg length weight Spare 7M= parts 0 for mm7m 550 mm 00 kg Stainless steel Set 7M= 9 mm 50 mm 5 kg Stainless steel Set () Scope Oval of Allen delivery head see screw, illustration retaining screw 50S89=M5x6 () Compression spring For Spare parts for 7M 5D8=.x.7 7M () () Oval Bearing Allen pinhead screw, retaining screw 50S89=M5x6 0M8 () () Compression Oval Allen head spring screw, retaining screw For 5D8=.x.7 7M 50S89=Mx6 () (5) Bearing pin ball Material Notice Product components which serve as spare parts for service and repair. Product components which serve as spare parts for service and repair. 0M8 509Y=5.0 Stainless steel () (6) Oval Set screw Allen head screw, retaining screw 50S89=Mx6 506G=M6x6 (5) (7) Bearing Stop pinball Material 509Y=5.0 Stainless steel 506A8=X8 506A8=X8 (6) Set screw 506A8=5x8 Article 506A8=5x0 number 506G=M6x6 (7) Stop pin 506A8=X8 506A8=X8 506A8=5x8 506A8=5x0 Explanation of symbols Explanations of hazardous substance symbols (P/H phrases)* Information sheet, poster Recommended for lamination resin technique Hazard classes Hazard categories Inflammable gases Explanation of symbols Recommended for Explanations of hazardous substance symbols (P/H phrases)* Information material Inflammable aerosols, prepreg technique Inflammable liquids,, Recommended for Information sheet, poster Hazard classes Hazard categories Processing instructions/ lamination Recommended resin for technique joint bar/ Inflammable solids, instructions for use clamp technique Inflammable Self-decomposing gases substances and mixtures Types B, C, D, E, F Recommended for Information material Inflammable Pyrophoric liquids aerosols, prepreg Recommended technique for Mixing ratio Inflammable Pyrophoric solids liquids, thermoplastic technique, Processing instructions/ Recommended for joint bar/ Inflammable Substances and solids mixtures capable,, of self-heating instructions for use clamp Products technique suitable for DVD Self-decomposing substances and mixtures Types B, C, D, E, F children Substances and mixtures that release Pyrophoric liquids,, inflammable gases upon contact with water Recommended for Mixing ratio Pyrophoric solids thermoplastic technique Organic peroxides Self-adhesive Adjustment adapter size Types B, C, D, E, F Substances and mixtures capable, of Acute self-heating toxicity (oral, dermal, inhalative) Products suitable for DVD Washable at 0 C, children Substances Skin irritationand mixtures that release 0 Adjustment adapter size,, gentle cycle inflammable Eye irritationgases upon contact with water Organic peroxides Self-adhesive Adjustment adapter size Skin sensitisation Types B, C, D, E, F 60 Washable at 60 C Adjustment adapter size Acute Specific toxicity target (oral, organ dermal, toxicity inhalative) (one-time exposure) Washable at 0 C, Skin irritation 0 Adjustment adapter size gentle cycle Respiratory system irritation Adjustment adapter size Eye irritation Anaesthetic effects Skin sensitisation 60 Washable at 60 C Adjustment adapter size Specific target organ toxicity (one-time exposure) * The hazardous substance symbols (R/S phrases and P/H phrases) printed in the catalogue correspond to the labelling requirements Respiratory system irritation for hazardous substances Adjustment at the time adapter of printing. size They refer to the raw material. Changes reserved. Anaesthetic effects Please note that the base colours shown in this catalogue may differ in actual effect. * The hazardous substance symbols (R/S phrases and P/H phrases) printed in the catalogue correspond to the labelling requirements for hazardous substances at the time of printing. They refer to the raw material. Changes reserved. Please note that the base colours shown in this catalogue may differ in actual effect. 6 Ottobock Custom-Orthotics

9 About this catalogue Searching, finding and ordering Custom-Orthotics Ottobock 7

10 AFO system joints 8 Ottobock Custom-Orthotics

11 AFO system joints AFO system joints In this section, you will find a selection of ankle joints and dynamic components; proven technology and highly modern functionality. Selection guide AFO... 0 Conventional ankle joints... System components... Prefabricated AFO's... 7 Custom-Orthotics Ottobock 9

12 AFO system joints Selection guide AFO Hip extensor 5 Hip flexor 5 Knee extensor 5 Knee flexor 5 Foot extensor 5 Dorsal flexor 0 7F5 Page 8 7B58 7B65 Page 8 Page 88 7F 7F 0 Page Ottobock R066 Ottobock Custom-Orthotics 7F5 7B65 7B6 7B59 7B5 Page 8 7F 7F Page 6 Page 5 7B07 Page 88 Page 88 7B8 7B9 Page 89 7F6 Page 7 7F8 Page 7

13 AFO system joints Selection guide AFO Hip extensor 5 Hip flexor 5 Knee flexor 5 Knee extensor 5 Foot extensor Dorsal flexor 0 7LA 7B66 Page Page - 7LS Page 7LA Page - 7LF Page 7LS Page 7LF Page 7Y8 Page 88 7B 7B 7B5 7B6 Page 7B8 7B9 Page 89 7CF* Page 0 Ottobock R06 Custom-Orthotics Ottobock

14 AFO system joints Selection guide AFO Hip extensor 5 Hip flexor 5 Knee flexor 5 < KAFO orthosis Knee extensor 5 Foot extensor 0 Dorsal flexor 0 7LA 7B66 Page Page - 7LS Page 7LA Page - 7LF Page Ottobock R06 Ottobock Custom-Orthotics 7LS Page 7LF Page 7Y8 Page 88 7B 7B 7B5 7B6 Page 7B8 7B9 Page 89 7CF* Page 0

15 AFO system joints Selection guide AFO 8U 8U / 8U 8U Page Page Page Custom fabrication Tipp Side Shoe size WalkOn =L6-9 left L 6 9 8U =R6-9 right R 6 9 WalkOn Flex =L9- left L 9 8U =R9- right R 9 WalkOn Trimable =L-5 left L 5 8U =R-5 right R 5 8Z0 Inlays WalkOn Reaction =L5-8 left L 5 8 Page generally recommendable 8U =R5-8 right R Custom-Orthotics Ottobock

16 AFO system joints Conventional ankle joints 7M Multifunction system ankle joint for integration in ankle foot orthoses with dorsal, plantar limitation or spring assist, incl. parallel alignment aid Article number Overall length upper section foot stirrup Max. lower leg length Max. body weight Material 7M= 0 mm 550 mm 00 kg Stainless steel Set 7M= 9 mm 50 mm 5 kg Stainless steel Set Scope of delivery see illustration 67G66 Spare parts for 7M () Oval Allen head screw, retaining screw 50S89=M5x6 () Compression spring for 5D8=.x.7 7M () Bearing pin 0M8 () Oval Allen head screw, retaining screw 50S89=Mx6 (5) Bearing ball Material 509Y=5.0 Stainless steel (6) Set screw 506G=M6x6 (7) Stop pin 506A8=X8 506A8=X8 506A8=5x8 506A8=5x0 Ottobock Custom-Orthotics

17 AFO system joints Conventional ankle joints 7M Free motion ankle joints Free motion ankle joints for ankle foot orthoses Article number Overall length upper section foot stirrup Max. lower leg length Max. body weight Material 7M= 77.5 mm 55 mm 00 kg Stainless steel Set 7M= 6.5 mm 5 mm 5 kg Stainless steel Set Simple tool for parallel adjustment is included in the delivery Scope of delivery see illustration 67G66 Spare parts for 7M () Oval Allen head screw, retaining screw for 50S89=M5x6 7M Custom-Orthotics Ottobock 5

18 AFO system joints Conventional ankle joints 7F Ankle joint bar for Side Bar width Head Ø Clevis width Material 7F=L6x.5 7F6 Left 5 mm 6 mm.5 mm Stainless steel 7F=R6x.5 7F6 Right 5 mm 6 mm.5 mm Stainless steel 7F=L8x 7F6 Left 6 mm 8 mm mm Stainless steel 7F=R8x 7F6 Right 6 mm 8 mm mm Stainless steel 7F=L0x 7F6 Left 7 mm 0 mm mm Stainless steel 7F=R0x 7F6 Right 7 mm 0 mm mm Stainless steel 67G 7F Ankle joint bar 67G for Side Bar width Head Ø Clevis width Material 7F=L6x.5 7F8 Left 5 mm 6 mm.5 mm Aluminium 7F=R6x.5 7F8 Right 5 mm 6 mm.5 mm Aluminium 7F=L8x 7F8 Left 6 mm 8 mm mm Aluminium 7F=R8x 7F8 Right 6 mm 8 mm mm Aluminium 7F=L0x 7F8 Left 7 mm 0 mm mm Aluminium 7F=R0x 7F8 Right 7 mm 0 mm mm Aluminium 6 Ottobock Custom-Orthotics

19 AFO system joints Conventional ankle joints 7F6 Ankle joint bars with shoe stirrup Joints with rear compression spring Article number Shoe stirrup length Shoe stirrup thickness Upper section length Joint head Ø Material 7F6=50 50 mm.5 mm 00 mm 6 mm Stainless steel Set 7F6=80 80 mm.5 mm 00 mm 6 mm Stainless steel Set 7F6=00 00 mm mm 90 mm 8 mm Stainless steel Set 7F6=0 0 mm mm 90 mm 8 mm Stainless steel Set 7F6=0 0 mm mm 90 mm 8 mm Stainless steel Set 7F6=60 60 mm mm 90 mm 0 mm Stainless steel Set 7F6=80 80 mm mm 90 mm 0 mm Stainless steel Set 7F6=00 00 mm mm 90 mm 0 mm Stainless steel Set 67G 7F8 Ankle joint bars with shoe stirrup Joints with compression spring, aluminium bars, stainless steel shoe stirrups Article number Shoe stirrup length Shoe stirrup thickness Upper section length Joint head Ø Material 7F8=50 50 mm.5 mm 00 mm 6 mm Aluminium Set 7F8=80 80 mm.5 mm 00 mm 6 mm Aluminium Set 7F8=00 00 mm mm 90 mm 8 mm Aluminium Set 7F8=0 0 mm mm 90 mm 8 mm Aluminium Set 7F8=0 0 mm mm 90 mm 8 mm Aluminium Set 7F8=60 60 mm mm 90 mm 0 mm Aluminium Set 7F8=80 80 mm mm 90 mm 0 mm Aluminium Set 7F8=00 00 mm mm 90 mm 0 mm Aluminium Set 67G Custom-Orthotics Ottobock 7

20 AFO system joints Conventional ankle joints Matching foot stirrups for 7F6 and 7F8 7B58 Foot stirrup Thickness Bar width Stirrup length Head Ø Material 7B58=6x.5x5.5 mm 6 mm 5 mm 6 mm Stainless steel 7B58=8xx65 mm 0 mm 65 mm 8 mm Stainless steel 7B58=0xx65 mm 0 mm 65 mm 0 mm Stainless steel 7F Shoe stirrup Thickness Head Ø Length from joint centre to joint centre Material 7F=50x.5.5 mm 6 mm 50 mm Stainless steel 7F=80x.5.5 mm 6 mm 80 mm Stainless steel 7F=00x.5.5 mm 6 mm 00 mm Stainless steel 7F=0x.5.5 mm 6 mm 0 mm Stainless steel 7F=0x.5.5 mm 6 mm 0 mm Stainless steel 7F=60x.5.5 mm 6 mm 60 mm Stainless steel 7F=80x.5.5 mm 6 mm 80 mm Stainless steel 7F=00x.5.5 mm 6 mm 00 mm Stainless steel 7F=00x mm 8 mm 00 mm Stainless steel 7F=0x mm 8 mm 0 mm Stainless steel 7F=0x mm 8 mm 0 mm Stainless steel 7F=60x mm 0 mm 60 mm Stainless steel 7F=80x mm 0 mm 80 mm Stainless steel 7F=00x mm 0 mm 00 mm Stainless steel Up to 0 mm extra length is available for an additional charge. 7F5 System shoe plate, hardened with insert piece Side System width Length Channel width Insertion depth Material 7F5=L0 Left 6 mm 0 mm 9 mm 60 mm Stainless steel 7F5=R0 Right 6 mm 0 mm 9 mm 60 mm Stainless steel 7F5=L50 Left 0 mm 50 mm mm 80 mm Stainless steel 7F5=R50 Right 0 mm 50 mm mm 80 mm Stainless steel 8 Ottobock Custom-Orthotics

21 AFO system joints Conventional ankle joints Spare parts for 7F6 and 7F8 () Bearing nut, hardened Shoulder Ø Shank length Thread 7Y9=7x6.8xM5 7 mm 6.8 mm M5 7Y9=9x7.xM6 9 mm 7. mm M6 for repairs: Bearing nut, hardened Shoulder Ø Shank length Thread 7Y9=7.5x6.8xM5 7.5 mm 6.8 mm M5 7Y9=9.5x7.xM6 9.5 mm 7. mm M6 () Slotted truss head screw Length Head Ø Thread Total length Material 50S=M5xx mm mm M5 9.5 mm Stainless steel 50S=M6xx0 0 mm mm M6 0 mm Stainless steel () Set screw with slot Thread Thread length Material 7Y8=M6x M6 mm Stainless steel 7Y8=M7x M7 mm Stainless steel () Bearing ball Material 509Y=/6 Stainless steel (5) Thrust piece with ball 7Y80 (6) Compression spring Length Shoulder Ø 5D8=.7x mm.7 mm 5D8=5.5x5 5 mm 5.5 mm 5D8=5.5x5 5 mm 5.5 mm Practical recommendation: On worn joints, the tolerance can be reduced with the repair bolts. A suitable reamer is usually used for adaptation. Custom-Orthotics Ottobock 9

22 AFO system joints Conventional ankle joints 7CF Carbon Ankle seven Mechanism of action The design of the carbon springs causes the initiation of the hip and knee-extending moments while walking and thus achieves extension and knee stability in the lower limbs. The energy generated during heel strike is stored in the carbon matrix and returned at toe-off. In contrast to conventional ankle foot orthoses, the limitations in the plantar and dorsal direction are dynamic and without static restriction. Indication Paralysis or weakness/restriction of the foot lifting and foot lowering muscles while using a dynamic ankle foot orthosis, of the knee extensors while using a knee ankle foot orthosis (KAFO) with locked knee joint. Diseases such as spina bifida or poliomyelitis are typical basic diseases. Benefits Positive influence on the gait pattern Very lightweight design 7 outward rotation supports physiological alignment of the foot Classification for straightforward product selection Suitable for thermoplastic and laminated orthoses Selecting and ordering The Carbon Ankle seven is selected on the basis of the user's body weight and activity level. Normal activity level: A normally active user performs all everyday activities in life independently and engages in rather easy activities. High activity level: A highly active user is unrestricted in everyday life. The orthosis of a highly active user must support quick changes from walking to running and vice versa, for example with people doing sports or with children. 66D=GB 67G6 0 Ottobock Custom-Orthotics

23 AFO system joints Conventional ankle joints Classification of the Carbon Ankle seven for AFOs In the classification matrix shown below, you will easily find the right article number. Then just select the side (e.g. 7CF=L9 for the left side with a normally active patient who weighs up to 0 kg/66 lbs). The delivery includes detailed mounting instructions as well as the attachment material needed for the integration into an orthosis. Max. body weight (normal activity) Max. body weight (high activity) Spring width 7CF=L/R 00 kg 00 kg 0 mm 7CF=L/R 90 kg 80 kg 0 mm 7CF=L/R 80 kg 70 kg 0 mm 7CF=L/R 70 kg 60 kg 0 mm 7CF=L/R5 60 kg 50 kg 0 mm 7CF=L/R6 50 kg - 5/0 mm 7CF=L/R7-0 kg 5 mm 7CF=L/R8 0 kg 0 kg 5 mm 7CF=L/R9 0 kg - 5 mm 7CF=L/R0-0 kg 5 mm 7CF=L/R 0 kg 0 kg mm 7CF=L/R 0 kg - mm 66D=GB The classification applies to AFOs that are intended to influence the knee joint. The use of the Carbon Ankle seven carbon spring for KAFOs may require a deviation from the classification. The specified weights have nothing to do with durability, but only with functionality. Single components 7CF Rosette washer 507U9=M5 507U9=M Phillips oval countersunk head screw 50S86=M5x 50S86=Mx Welding nut 50E=M5x7,5 50E=Mx6 Custom-Orthotics Ottobock

24 AFO system joints System components 7B66 Multifunction system ankle joint Multifunction system ankle joint with up to 9 setting options (spring, fixed stop or spring stop) 66A 67G 67G67 System width Clevis width Material 7B66=6 6 mm mm Stainless steel Pair with screws 7B66=0 0 mm mm Stainless steel Pair with screws 7B66=A-6* 6 mm mm Stainless steel Pair with screws 7B66=A-0* 0 mm mm Stainless steel Pair with screws *medial and lateral joint straight, lateral bar connection Practical recommendation: Increased wear of the spring due to fully compressing it. The cylinder pin is inside the spring. Using the cylinder pin can extend the life of the spring. Ottobock Custom-Orthotics

25 AFO system joints System components Accessories 7B System foot stirrup free motion up to 5 plantar flexion and 5 dorsal extension, with brass bushing Material 7B Stainless steel 7B System foot stirrup free motion up to 5 plantar flexion and 5 dorsal extension, with brass bushing Material 7B Stainless steel 7B5 System foot stirrup for 7F5=L/R50 system shoe plate free motion up to 5 plantar flexion and 5 dorsal extension, with brass bushing Material 7B5 Stainless steel 7B6 System shoe stirrup free motion up to 5 plantar flexion and 5 dorsal extension, with brass bushing System width Thickness Length from joint centre Material 7B6=80 0 mm mm 80 mm Stainless steel 7B6=00 0 mm mm 00 mm Stainless steel 7B6=0 0 mm mm 0 mm Stainless steel 7B6=0 0 mm mm 0 mm Stainless steel 7B6=60 0 mm mm 60 mm Stainless steel 7B6=80 0 mm mm 80 mm Stainless steel 7B6=00 0 mm mm 00 mm Stainless steel Custom-Orthotics Ottobock

26 AFO system joints System components 7Y7=9xx.9 Brass bushing Material 7Y7=9xx.9 Brass 7B66=S Service set for 7B66 Scope of delivery 7B66=S Set x 5D8=.7x x 506A8=5x x 506A8=.5x8 x 509Y=5.0 x 506G=M6x6 x 7Y9=9x6.5xM6 x 50S=M6xx0 Spare parts for 7B66 () Bearing nut, hardened For system width Shoulder Ø Shank length Thread 7Y9=9x6.5xM6 0/6 mm 9 mm 6.5 mm M6 () Slotted truss head screw For system width Head Ø Thread Total length Material 50S=M6xx0 0/6 mm mm M6 0 mm Stainless steel () Compression spring Shoulder Ø 5D8=.7x.7 mm () Bearing ball Material 509Y=5.0 Stainless steel (5) Stop pin 506A8=.5x8 506A8=5x (6) Set screw 506G=M6x6 Ottobock Custom-Orthotics

27 AFO system joints System components 7B6 / 7B59 / 7B5 System ankle joints Joint with dorsiflexion function and dorsal stop to be established by filing the foot stirrup 67G Contoured medial joint, straight lateral joint, with compression spring Side System width Head Ø Clevis width Length from joint centre Material 7B6=L6 Left 6 mm 6 mm.5 mm 57 mm Stainless steel Pair 7B6=R6 Right 6 mm 6 mm.5 mm 57 mm Stainless steel Pair 7B6=L0 Left 0 mm 8 mm mm 66 mm Stainless steel Pair 7B6=R0 Right 0 mm 8 mm mm 66 mm Stainless steel Pair Straight medial and lateral joint, with compression spring System width Head Ø Clevis width Length from joint centre Single joint Material 7B59=6 6 mm 6 mm.5 mm 57 mm 7A59=L/R6 Stainless steel Pair 7B59=0 0 mm 8 mm mm 66 mm 7A59=L/R0 Stainless steel Pair Contoured medial joint and lateral joint, with compression spring System width Head Ø Clevis width Length from joint centre Single joint Material 7B5=6 6 mm 6 mm.5 mm 57 mm 7A5=L/R6 Stainless steel Pair 7B5=0 0 mm 8 mm mm 66 mm 7A5=L/R0 Stainless steel Pair Practical recommendation: To isolate the joints for the lamination resin technique, we recommend 66K8=0xx0 plastaband. Increased wear of the spring due to fully compressing it. Custom-Orthotics Ottobock 5

28 AFO system joints System components Matching foot stirrups for 7B6, 7B59, 7B5 7B08 System foot stirrup with brass bushing, dorsal stop to be established by filing, and 0 plantar flexion System width Thickness Length from joint centre Material 7B08=5x.5 6 mm.5 mm 5 mm Stainless steel 7B08=65x 0 mm mm 65 mm Stainless steel 7B99 System lamination foot stirrup free motion up to 0 dorsal extension and 0 plantar flexion, with brass bushing System width Thickness Length from joint centre Material 7B99=6 6 mm.5 mm 6 mm Stainless steel 7B99=0 0 mm mm 6 mm Stainless steel 7B0 System lamination foot stirrup with dorsal stop and 0 plantar flexion, with brass bushing System width Thickness Length from joint centre Material 7B0=6 6 mm.5 mm 6 mm Stainless steel 7B0=0 0 mm mm 6 mm Stainless steel 7B07 Foot stirrup with dorsal stop to be established by filing, and 0 plantar flexion System width Thickness Head Ø Length from joint centre Material 7B07=5x.5 6 mm.5 mm mm 5 mm Stainless steel 7B07=65x 0 mm mm mm 65 mm Stainless steel 6 Ottobock Custom-Orthotics

29 AFO system joints System components 7F70 System shoe stirrup with brass bushing, dorsal stop to be established by filing, and 0 plantar flexion System width Thickness Length from joint centre to joint centre Material 7F70=50x.5 6 mm.5 mm 50 mm Stainless steel 7F70=80x.5 6 mm.5 mm 80 mm Stainless steel 7F70=00x.5 6 mm.5 mm 00 mm Stainless steel 7F70=0x.5 6 mm.5 mm 0 mm Stainless steel 7F70=0x.5 6 mm.5 mm 0 mm Stainless steel 7F70=60x.5 6 mm.5 mm 60 mm Stainless steel 7F70=80x.5 6 mm.5 mm 80 mm Stainless steel 7F70=00x.5 6 mm.5 mm 00 mm Stainless steel 7F70=00x 0 mm mm 00 mm Stainless steel 7F70=0x 0 mm mm 0 mm Stainless steel 7F70=0x 0 mm mm 0 mm Stainless steel 7F70=60x 0 mm mm 60 mm Stainless steel 7F70=80x 0 mm mm 80 mm Stainless steel 7F70=00x 0 mm mm 00 mm Stainless steel Up to 0 mm extra length is available for an additional charge. 7F5 System shoe plate, hardened with insert piece Side System width Length Channel width Insertion depth Material 7F5=L0 Left 6 mm 0 mm 9 mm 60 mm Stainless steel 7F5=R0 Right 6 mm 0 mm 9 mm 60 mm Stainless steel 7F5=L50 Left 0 mm 50 mm mm 80 mm Stainless steel 7F5=R50 Right 0 mm 50 mm mm 80 mm Stainless steel 7Y7 Brass bushing System width 7Y7=7x9x. 6 mm 7Y7=9xx.9 0 mm Custom-Orthotics Ottobock 7

30 AFO system joints System components Spare parts for 7B6, 7B59 and 7B5 () Bearing nut, hardened System width Shoulder Ø Shank length Thread 7Y9=7x6.8xM5 6 mm 7 mm 6.8 mm M5 7Y9=9x7.xM6 0 mm 9 mm 7. mm M6 () Slotted truss head screw System width Head Ø Thread Total length Material 50S=M5xx9.5 6 mm mm M5 9.5 mm Stainless steel 50S=M6xx0 0 mm mm M6 0 mm Stainless steel () Compression spring System width Length Shoulder Ø 5D8=.7x 6 mm mm.7 mm 5D8=5.5x5 0 mm 5 mm 5.5 mm () Set screw with slot System width Thread Thread length Material 7Y8=M6x 6 mm M6 mm Stainless steel 7Y8=M7x 0 mm M7 mm Stainless steel (5) Bearing ball For system width Size Material 509Y=/6 6 mm Stainless steel (6) Thrust piece with ball For system width 7Y80 0 mm (7) Phillips oval countersunk head screw Length Material 50T7=7.5x9xM5 9 mm Stainless steel 8 Ottobock Custom-Orthotics

31 AFO system joints System components 7PA CarbonIQ ankle joint The 7PA=0 ankle joint is a double-action joint and is based on the Ottobock 7B66 ankle joint. This type of joint is by far the most versatile fitting. The 9 different possibilities for settings and combinations (see fig.) allow the joint's functions to be adapted to the user's requirements at any time, even if these change over the course of the fitting. Different versions for influencing plantar flexion and dorsal extension are available. Side Max. body weight Material 7PA=0 Left and right 00 kg Fibre-reinforced plastic Pair The CarbonIQ joints are resistant against splashed water! 66D578=EN 66T5=.6EN 67G6 Accessories 7PF Foot stirrup Material 7PF Stainless steel Custom-Orthotics Ottobock 9

32 AFO system joints System components Spare parts for 7PA () Set screw 506G6=M6x () Stop pin 506A8=5x0 () Service set Scope of delivery 9PA Set x 50S8=M6X x 0Y5 x 509G0=XX x 0Y () Set screw 506G=Mx (5) Bearing ball Material 509Y=5.0 Stainless steel (6) Stop pin 506A8=.5x8 (7) Compression spring 5D8=.7x- (8) Adjustment Aid Scope of delivery 9PK Set x 50T8=M6X5 x 0Y6 0 Ottobock Custom-Orthotics

33 AFO system joints System components 7LA Unilateral System Ankle Joint The 7LA Unilateral Ankle Joint is a multifunction system ankle joint with a foot-lifting effect. Various combination possibilities allow it to be quickly adjusted to the individual user's needs at any time. Its weight classification permits unilateral use for a patient weight of up to 00 kg and bilateral use for up to 60 kg. Despite its multifunctional features, it is small, light and inconspicuous truly versatile. Custom-Orthotics Ottobock

34 AFO system joints System components 7LA Unilateral System Ankle Joint System width Max. body weight Material 7LA= 0 kg (unilateral)/0 kg (bilateral) Steel 7LA=-T 0 kg (unilateral)/0 kg (bilateral) Titanium 7LA= 50 kg (unilateral)/80 kg (bilateral) Steel 7LA=-T 50 kg (unilateral)/80 kg (bilateral) Titanium 7LA= kg (unilateral)/0 kg (bilateral) Steel 7LA=6-T 6 85 kg (unilateral)/0 kg (bilateral) Titanium 7LA=0 0 0 kg (unilateral)/60 kg (bilateral) Steel 7LA=0-T 0 0 kg (unilateral)/60 kg (bilateral) Titanium 66D789=EN 67G86 When using the product unilaterally, and in case of flexion contracture in the knee or hip > 0 or distinct torsion or valgus/varus instabilities or increased physical activity, the next higher size must be used. For tubercle seat or valgus/varus malpositions > 0 the product must be fitted bilaterally. Nine different combination possibilities of stop, spring and spring stop. Ottobock Custom-Orthotics

35 AFO system joints System components Accessories 7LF Foot stirrup for Unilateral Ankle Joints Free motion up to 0 plantar flexion and 0 dorsal extension, only in combination with the 7LA=* ankle joint for Material 7LF= 7LA= Stainless steel 7LF= 7LA= Stainless steel 7LF=6 7LA=6 Stainless steel 7LF=0 7LA=0 Stainless steel 7LS Lamination bar for Unilateral Joint System Length Width Material 7LS= 80 mm mm Stainless steel 7LS=-T 80 mm mm Titanium 7LS= 00 mm mm Stainless steel 7LS=-T 00 mm mm Titanium 7LS=6 0 mm 6 mm Stainless steel 7LS=6-T 0 mm 6 mm Titanium 7LS=0 0 mm 0 mm Stainless steel 7LS=0-T 0 mm 0 mm Titanium 7LD Lamination dummy for Unilateral Ankle Joint incl. shoulder screw for Material 7LD= 7LA= Stainless steel 7LD= 7LA= Stainless steel 7LD=6 7LA=6 Stainless steel 7LD=0 7LA=0 Stainless steel Custom-Orthotics Ottobock

36 AFO system joints System components Spare parts for 7LA () Set screw for 506G=M5x5 7LA= 0Y= 7LA= 0Y=6-0 7LA=6 7LA=0 () Stop pin for 506A8=X8 7LA= 506A8=X8 7LA= 506A8=.5x8 7LA=6 7LA=0 () Compression spring for 5D87=0.75X.95X 7LA= 5D87=.X.8X8 7LA= for 0Y5=6 7LA=6 Pair 0Y5=0 7LA=0 Pair () Stop pin for 506A8=X6 7LA= 506A8=6X0 7LA= 506A8=8X6 7LA=6 7LA=0 (5) Bearing ball for Material 509Y=.0 7LA= Stainless steel 509Y=6.0 7LA= Stainless steel 509Y=8.0 7LA=6 7LA=0 Stainless steel (6) Stop dummy for 0Y6= 7LA= 0Y6= 7LA= 0Y6=6-0 7LA=6 7LA=0 (7) Spare parts set 7LA for 7LA0N= 7LA= Set 7LA0N= 7LA= Set 7LA0N=6 7LA=6 Set 7LA0N=0 7LA=0 Set Ottobock Custom-Orthotics

37 AFO system joints System components (8) Countersunk head screw (Allen screw) with socket head for 50S=MX9 7LA= 50S=MX0 7LA= 50S=M5X 7LA=6 50S=M5X 7LA=0 Custom-Orthotics Ottobock 5

38 Unilateral Joint System Order form fax: +9 (0) Company Technician Customer no. Date Signature User information Surname, first name Age Weight Indication Side L e ft Right Bilateral The size chosen depends on the patient s weight and the conditions of use. (A)* 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 7LK=* Unilateral Knee Joint Steel version Titanium version (A) Shoulder screw* 7LK= 7LK=-T L R 0Y89 7LK= 7LK=-T L R 0Y89 7LK=6 7LK=6-T L R 0Y89 7LK=0 7LK=0-T L R 0Y89 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 5 (B) 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 5 7LA=* Unilateral Ankle Joint Steel version Titanium version (B) Optional lamination dummy with shoulder screw * (A) The 0Y89 shoulder screw is not included in the scope of delivery of 7LK. It is part of the 7R6 orthotic joint alignment fixture. 6 7LA= 7LA=-T 7LD= 7LA= 7LA=-T 7LD= 7LA=6 7LA=6-T 7LD=6 7LA=0 7LA=0-T 7LD=0 6 7LF=* Foot stirrup 7LF= 7LF=6 7LF= 7LF=0

39 AFO system joints Prefabricated AFO's Custom-Orthotics Ottobock 7

40 AFO system joints Prefabricated AFO's 8U90 Ankle foot orthosis Order example Reference number = Side Size Coulor 8U90 = L U90 Size Colour transparent, black (7) Side Left (L), Right (R) Height 90 mm 5 mm 5 mm 90 mm 5 mm Spare parts for 8U90 9U90 Calf pad with strap 9U90 Size , - -7 Colour beige (9), black (7) 8U WalkOn Order example Reference number = Side Size Coulor 8U = L U Size Side Left (L), Right (R) Height 50 mm 60 mm 70 mm 90 mm 8U WalkOn Trimable Order example Reference number = Side Size Coulor 8U = L U Size Side Left (L), Right (R) Height 50 mm 60 mm 70 mm 90 mm 8 Ottobock Custom-Orthotics

41 AFO system joints Prefabricated AFO's Spare parts for 8U and 8U 6Z9 WalkOn calf pad with Outlast Side Size 6Z9=L Left 6-8 6Z9=R Right 6-8 8U WalkOn Flex Order example Reference number = Side Size Coulor 8U = L U Size Side Left (L), Right (R) Height 50 mm 60 mm 70 mm 90 mm Accessories for 8U 9U5 Calf pad Side Size 9U5=L Left 50 9U5=R Right 50 9U5=L Left 9U5=R Right Spare parts for 8U 8Z0 Lateral pronation strap A 8Z0 pronation strap can be used as additional option to counteract spastic supination of the foot. 8Z0 Size Universal 8Z0 is included in the 8U scope of delivery. Custom-Orthotics Ottobock 9

42 AFO system joints Prefabricated AFO's 8U WalkOn Reaction Order example Reference number = Side Size Coulor 8U = L U Size Height mm 55 mm 77 mm 00 mm Side Left (L), Right (R) Accessories for 8U 8Z0 Lateral pronation strap A 8Z0 pronation strap can be used as additional option to counteract spastic supination of the foot. 8Z0 Size Universal 8Z0 is included in the 8U scope of delivery. 9U Shin pad 9U Size Universal 9U5 Y-hook-and-loop Size 9U5= 9U5= 9U Pad for WalkOn Reaction incl. hook-and-loop closures 9U Size Material Outlast Side Left (L), Right (R) 0 Ottobock Custom-Orthotics

43 Notes Custom-Orthotics Ottobock

44 KAFO system joints Ottobock Custom-Orthotics

45 KAFO system joints KAFO system joints You will find a selection of knee joints and knee joint systems in this section; traditional mechanical and mechatronic Selection guide KAFO... Locked joints... 7 Free motion system joints SCO system joints... 6 Waterproof orthoses Correction system joints... 8 Custom-Orthotics Ottobock

46 KAFO system joints Selection guide KAFO Hip extensor 0 Hip flexor 0 Knee flexor 0 Knee extensor 0 Foot extensor 0 Dorsal flexor 0 7LK=* 7B=* 7LK=* Page Page Page LA=* 7B66=* Page Page - OR OR 7CF=* 7CF=* Page Page 0 0 Ottobock Custom-Orthotics

47 KAFO system joints Selection guide KAFO Hip extensor Hip flexor Knee flexor 0 Knee extensor 0 Foot extensor 0 Dorsal flexor 0 7B0=* 7B0=* 7B05=* Page Page Page K=* Page 68 7LA=* 7B66=* Page Page - OR OR 7CF=* 7CF=* Page Page 0 0 Custom-Orthotics Ottobock 5

48 KAFO system joints Selection guide KAFO Hip extensor 5 Hip flexor 5 Knee extensor 5 Knee flexor 0 Dorsal flexor 0 Foot extensor 0 7LK=* (free-moving) 7B6=* Page Page LA=* 7B66=* Page - Page Stop (dorsal) Dorsiflexion assist with adjustable dorsal stop (e.g. peroneal paralysis with or without knee joint protection) 6 Stop (dorsal) Dorsiflexion assist with adjustment of plantar and dorsal stop (e.g. peroneal paralysis with hyperextension of the knee joint) Ottobock Custom-Orthotics Stop (dorsal) Dorsiflexion assist with adjustable dorsal stop (e.g. peroneal paralysis with or without knee joint protection) Stop (dorsal) Dorsiflexion assist with adjustment of plantar and dorsal stop (e.g. peroneal paralysis with hyperextension of the knee joint)

49 KAFO system joints Locked joints 7B / 7BK / 7B5 / 7B9 System knee joints 67H Contoured medial joint, straight lateral joint, with covered lock centrally* fitted, lock lever, with pull-release cable Side System width Length from joint centre upper/lower Material 7B=L6 Left 6 mm 56 / 8 mm Stainless steel Pair 7B=R6 Right 6 mm 56 / 8 mm Stainless steel Pair 7B=L0 Left 0 mm 56 / 8 mm Stainless steel Pair 7B=R0 Right 0 mm 56 / 8 mm Stainless steel Pair Contoured medial joint, straight lateral joint, with covered lock eccentrically* fitted, lock lever, with pull-release cable Side System width Length from joint centre upper/lower Material 7B=L6K Left 6 mm 56 / 8 mm Stainless steel Pair 7B=R6K Right 6 mm 56 / 8 mm Stainless steel Pair 7B=L0K Left 0 mm 56 / 8 mm Stainless steel Pair 7B=R0K Right 0 mm 56 / 8 mm Stainless steel Pair Straight medial and lateral joints, with covered lock, lock lever points upward* System width Length from joint centre upper/lower Material 7B5=6 6 mm 56 / 8 mm Stainless steel Pair 7B5=0 0 mm 56 / 8 mm Stainless steel Pair Medial joint contoured bottom, straight top, lateral joint straight, with covered lock*, lock lever points upward Side System width Length from joint centre upper/lower Material 7B9=L6 Left 6 mm 56 / 8 mm Stainless steel Pair 7B9=R6 Right 6 mm 56 / 8 mm Stainless steel Pair 7B9=L0 Left 0 mm 56 / 8 mm Stainless steel Pair 7B9=R0 Right 0 mm 56 / 8 mm Stainless steel Pair * Attention: Eccentric and concentric locking lever constructions can not be mixed, otherwise the reliable barrier function can not be guaranteed! Custom-Orthotics Ottobock 7

50 KAFO system joints Locked joints Spare parts for 7B/7BK/7B5/7B9 () Lock lever for Material 7Y0 7B 7B5 7B9 Stainless steel 0Y6 7BK Stainless steel () Bearing nut, hardened for system knee joint Thread For system width Shank length Shoulder Ø 7Y9=9x9.xM6 M6 6 and 0 mm 9. mm 9 mm for repairs: Thread For system width Shank length Shoulder Ø 7Y9=9.5x9.xM6 M6 6 and 0 mm 9. mm 9.5 mm () Slotted truss head screw for Thread Length For system width 50S=Mx8x Lock lever M mm 6 and 0 mm 50S=M6xx Knee joint M6 mm 6 and 0 mm 50S=M6xx7.5 Knee joint* M6 7.5 mm 6 and 0 mm *(when using 7Y8) () Knee cap ring plate Material Stainless steel Stainless steel Stainless steel 7Y8 (5) Oval head screw, slotted and partially threaded for Material 50A=x9xM6 Stainless steel (6) Compression spring for 5D9=.8x6 7B 7B5 7B9 7BK (7) Phillips oval countersunk head screw Thread Head Ø Material 50T7=7.5x9xM5 M5 7.5 mm Stainless steel (8) Bearing nut, hardened for lock lever Thread For system width Shank length Shoulder Ø 7Y9=6x9.5xM M 6 and 0 mm 9.5 mm 6 mm 8 Ottobock Custom-Orthotics

51 KAFO system joints Locked joints for repairs: Thread For system width Shank length Shoulder Ø 7Y9=6.5x9.5xM M 6 and 0 mm 9.5 mm 6.5 mm 7MS0=A Service set for 7MS0=A 7BK Pair The pull-release cable can be positioned anteriorly or posteriorly. Thanks to the change of direction, less force is required for pulling. Side bars must be ordered separately. Custom-Orthotics Ottobock 9

52 KAFO system joints Locked joints 7B / 7B0 / 7B Modular system knee joints Locked knee joint with ring lock 67G Medial and lateral joints straight, with ring lock System width Milled head Length from joint centre upper/lower Material 7B=6 6 mm 5x mm 56 / 8 mm Stainless steel Pair 7B=0 0 mm 5x mm 56 / 8 mm Stainless steel Pair Contoured medial joint, straight lateral joint, with ring lock Side System width Milled head Length from joint centre upper/lower Material 7B0=L6 Left 6 mm 5x mm 56 / 8 mm Stainless steel Pair 7B0=R6 Right 6 mm 5x mm 56 / 8 mm Stainless steel Pair 7B0=L0 Left 0 mm 5x mm 56 / 8 mm Stainless steel Pair 7B0=R0 Right 0 mm 5x mm 56 / 8 mm Stainless steel Pair Lower segment of the medial joint contoured, upper segment straight, lateral joint straight, with ring lock Side System width Milled head Length from joint centre upper/lower Material 7B=L6 Left 6 mm 5x mm 56 / 8 mm Stainless steel Pair 7B=R6 Right 6 mm 5x mm 56 / 8 mm Stainless steel Pair 7B=L0 Left 0 mm 5x mm 56 / 8 mm Stainless steel Pair 7B=R0 Right 0 mm 5x mm 56 / 8 mm Stainless steel Pair 50 Ottobock Custom-Orthotics

53 KAFO system joints Locked joints Spare parts for 7B, 7B0 and 7B () Ring lock Material 7Y=5x9.5 Stainless steel () Bearing nut, hardened Thread Profile length Shank length Shoulder Ø 7Y9=9x7.xM6 M6 mm 7. mm 9 mm For repairs () Bearing nut, hardened Thread Profile length Shank length Shoulder Ø 7Y9=9.5x7.xM6 M6 mm 7. mm 9.5 mm () Two-hole screw Material 50S=M6 Stainless steel (5) Spring-loaded thrust piece Material 50D Stainless steel (6) Phillips oval countersunk head screw Material 50T7=7.5x9xM5 Stainless steel Practical recommendation: On worn joints, the tolerance can be reduced with the repair bolts. A suitable reamer is usually used for adaptation. Custom-Orthotics Ottobock 5

54 KAFO system joints Locked joints 7B6 / 7B8 / 7B90 System knee joints 67H5 Medial joint contoured, straight top, with Swiss lock Side System width Length from joint centre upper/lower Material 7B6=L6 Left 6 mm 56 / 8 mm Stainless steel Pair 7B6=R6 Right 6 mm 56 / 8 mm Stainless steel Pair 7B6=L0 Left 0 mm 56 / 8 mm Stainless steel Pair 7B6=R0 Right 0 mm 56 / 8 mm Stainless steel Pair Straight free motion medial and lateral joint, with Swiss lock System width Length from joint centre upper/lower Material 7B8=6 6 mm 56/8 mm Stainless steel Pair 7B8=0 0 mm 56/8 mm Stainless steel Pair Medial joint contoured bottom, straight top, straight lateral join, with Swiss lock Side System width Length from joint centre upper/lower Material 7B90=L6 Left 6 mm 56 / 8 mm Stainless steel Pair 7B90=R6 Right 6 mm 56 / 8 mm Stainless steel Pair 7B90=L0 Left 0 mm 56 / 8 mm Stainless steel Pair 7B90=R0 Right 0 mm 56 / 8 mm Stainless steel Pair 5 Ottobock Custom-Orthotics

55 KAFO system joints Locked joints 7PK=* CarbonIQ knee joint with wedge lock The 7PK=* knee joint is a locked joint made of fibre-reinforced plastic with a pull-release cable. The locking system uses the latest technology for locked joints and offers a high level of security. It can be unlocked with one hand using the pull-release cable, making it very simple to use. The lock in the joint clicks into place automatically when standing up, without there being a risk of trapping clothes. Side Max. body weight Material 7PK=L0 Left 00 kg Plastic reinforced with carbon fibre Pair 7PK=R0 Right 00 kg Plastic reinforced with carbon fibre Pair The CarbonIQ joints are resistant against splashed water! 66D578=EN 66T5=.6EN 67G6 67G6 Spare parts for 7PK () Service set Scope of delivery 9PK Set x 50S6=.0X x 0Y06 x A8= x 5D5= x A x 0Y07 () Service set Scope of delivery 9PK Set x 509G0=X6X5 x 0Y0 x 50T9=M6X8 x 0Y09 () Adjustment Aid Scope of delivery 9PK Set x 50T8=M6X5 x 0Y6 () Set screw 506G=Mx for 7PK=* Custom-Orthotics Ottobock 5

56 KAFO system joints Locked joints 7LK Unilateral Knee Joint The 7LK Unilateral Knee Joint is a system knee joint with wedge lock. It is particularly attractive due to its lightweight construction. Its weight classification permits unilateral use for a body weight of up to 0 kg and bilateral use for up to 60 kg. The system is suitable for prepreg and lamination resin techniques. The scope of delivery includes a temporary switch for releasing the joint, e.g. for training on a therapeutic bike. 5 Ottobock Custom-Orthotics

57 KAFO system joints Locked joints 7LK Unilateral Knee Joint System knee joint with wedge lock Side System width Max. body weight Material 7LK=L Left mm 0 kg / 0 kg* Steel 7LK=L - T Left mm 0 kg / 0 kg* Titanium 7LK=R Right mm 0 kg / 0 kg* Steel 7LK=R - T Right mm 0 kg / 0 kg* Titanium 7LK=L Left mm 50 kg / 80 kg* Steel 7LK=L - T Left mm 50 kg / 80 kg* Titanium 7LK=R Right mm 50 kg / 80 kg* Steel 7LK=R - T Right mm 50 kg / 80 kg* Titanium 7LK=L6 Left 6 mm 85 kg / 0 kg* Steel 7LK=L6 - T Left 6 mm 85 kg / 0 kg* Titanium 7LK=R6 Right 6 mm 85 kg / 0 kg* Steel 7LK=R6 - T Right 6 mm 85 kg / 0 kg* Titanium 7LK=L0 Left 0 mm 0 kg / 60 kg* Steel 7LK=L0 - T Left 0 mm 0 kg / 60 kg* Titanium 7LK=R0 Right 0 mm 0 kg / 60 kg* Steel 7LK=L0 - T Right 0 mm 0 kg / 60 kg* Titanium * with bilateral use When using the product unilaterally, and in case of flexion contracture in the knee or hip > 0 or distinct torsion or valgus/varus instabilities or valgus/varus malpositions or increased physical activity, the next higher size must be used! For tubercle seat the product must be fitted bilaterally. Accessories 7LS Lamination bar for Unilateral Joint System Length Width Thickness Material 7LS= 80 mm mm 5 mm bottom, mm top Stainless steel 7LS=-T 80 mm mm 5 mm bottom, mm top Titanium 7LS= 00 mm mm 6 mm bottom,.5 mm top Stainless steel 7LS=-T 00 mm mm 6 mm bottom,.5 mm top Titanium 7LS=6 0 mm 6 mm 6 mm bottom, mm top Stainless steel 7LS=6-T 0 mm 6 mm 6 mm bottom, mm top Titanium 7LS=0 0 mm 0 mm 6 mm bottom, mm top Stainless steel 7LS=0-T 0 mm 0 mm 6 mm bottom, mm top Titanium Custom-Orthotics Ottobock 55

58 KAFO system joints Locked joints Spare parts for 7LK () Knee lever for 0Y65= 7LK= 0Y65= 7LK= 0Y65=6 7LK=6 0Y65=0 7LK=0 () Lock washer for 507S96=. 7LK () Bearing nut, hardened for 7Y9=9x9.xM6 7LK=, = 7Y9=9x0.75xM6 7LK=6 7Y9=9x.75xM6 7LK=0 () Lock washer for 507S96= 7LK=6, =0 507S96=. 7LK=,= (5) Compression spring for 5D8= LK=, =6, =0 5D8=0.75x.x9 7LK= (6) Lock wedge for 7Y56 / 7Y57 / 7Y58 7LK=, = 7Y57 7LK=6 7Y58 7LK=0 Lock wedges must always be replaced with identical lock wedges (=, = or =) (7) Bushing for 0Y87= 7LK=6, =0 0Y87= 7LK=, = (8) Bearing washers for 70Z9= 7LK=6, =0 Set (9) Axle for A0=5x0.6 7LK=, = A0=6x.7 7LK=6 A0=6x.7 7LK=0 56 Ottobock Custom-Orthotics

59 KAFO system joints Locked joints (0) Screw with flattened half-round head for 50F7=M6x8 7LK=, = 50F7=M6x0 7LK=6, =0 () Axle for A0=.x5. 7LK=, = A0=x7. 7LK=6 A0=x8. 7LK=0 () Axle for A0= 5. 7LK=, = A0=x7. 7LK=6 A0=x8. 7LK=0 () Countersunk head screw (Allen screw) for 50S=MX0 7LA= 50S=M5X 7LA=6 () Protective plug for 0Y9= 7LK=6, =0 0Y9= 7LK=, = (5) Washer for 0Y67=. 7LK (all sizes) (6) Washer for 0Y67=. 7LK (all sizes) (7) Joint dummy for 0Y68= 7LK= 0Y68= 7LK= 0Y68=6 7LK=6 0Y68=0 7LK=0 The article number of the matching shoulder screw for the joint dummy is 0Y89. (8) Temporary switch for 7Y6= 7LK=, = 7Y6= 7LK=6 7Y6= 7LK=0 Custom-Orthotics Ottobock 57

60 Unilateral Joint System Order form fax: +9 (0) Company Technician Customer no. Date Signature User information Surname, first name Age Weight Indication Side L e ft Right Bilateral The size chosen depends on the patient s weight and the conditions of use. (A)* 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 7LK=* Unilateral Knee Joint Steel version Titanium version (A) Shoulder screw* 7LK= 7LK=-T L R 0Y89 7LK= 7LK=-T L R 0Y89 7LK=6 7LK=6-T L R 0Y89 7LK=0 7LK=0-T L R 0Y89 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 5 (B) 7LS=* Lamination bar Steel version Titanium version 7LS= 7LS=-T 7LS= 7LS=-T 7LS=6 7LS=6-T 7LS=0 7LS=0-T 5 7LA=* Unilateral Ankle Joint Steel version Titanium version (B) Optional lamination dummy with shoulder screw * (A) The 0Y89 shoulder screw is not included in the scope of delivery of 7LK. It is part of the 7R6 orthotic joint alignment fixture. 6 7LA= 7LA=-T 7LD= 7LA= 7LA=-T 7LD= 7LA=6 7LA=6-T 7LD=6 7LA=0 7LA=0-T 7LD=0 6 7LF=* Foot stirrup 7LF= 7LF=6 7LF= 7LF=0

61 KAFO system joints Free motion system joints 7K / 7K Knee joint bars for children Free motion knee joint bar 67G Joints require grinding, joint centre 5 mm to the posterior Upper/lower bar length Bar width/thickness Joint head Ø Material 7K=6 0 / 50 mm / mm 6 mm Stainless steel Pair 7K=5 0 / 50 mm / mm 8 mm Stainless steel Pair 7K= 0 / 50 mm 6 / mm 0 mm Stainless steel Pair Knee joint extension stop can be adjusted by filing, flat bar profile, no posterior placement Upper/lower bar length Bar width/thickness Joint head Ø Material 7K=6 0 / 50 mm / mm 6 mm Stainless steel Pair 7K=5 00 / 0 mm / mm 8 mm Stainless steel Pair 7K= 0 / 90 mm 6 / mm 0 mm Stainless steel Pair Spare parts for 7K and 7K () Knee joint bar upper section for Side Material 7X9=L6 7K=6 Left Stainless steel 7X9=R6 7K=6 Right Stainless steel 7X8=L6 7K=6 Left Stainless steel 7X8=R6 7K=6 Right Stainless steel 7X9=L5 7K=5 Left Stainless steel 7X9=R5 7K=5 Right Stainless steel 7X8=L5 7K=5 Left Stainless steel 7X8=R5 7K=5 Right Stainless steel 7X9=L 7K= Left Stainless steel 7X9=R 7K= Right Stainless steel 7X8=L 7K= Left Stainless steel 7X8=R 7K= Right Stainless steel Custom-Orthotics Ottobock 59

62 KAFO system joints Free motion system joints () Knee joint bar lower section for Material 7U9=6 7K=6 Stainless steel 7U8=6 7K=6 Stainless steel 7U9=5 7K=5 Stainless steel 7U8=5 7K=5 Stainless steel 7U9= 7K= Stainless steel 7U8= 7K= Stainless steel () Slotted truss head screw for Thread Length Material 50S=Mx0x9.5 7K=6 7K=5 7K=6 7K=5 50S=M6xx0 7K= 7K= M 9.5 mm Stainless steel M6 0 mm Stainless steel () Bearing nut, hardened for Thread Shank length Shoulder Ø 7Y9=6x6.7xM 7K=5 7K=6 M 6.7 mm 6 mm 7Y9=9x7.xM6 7K= M6 7. mm 9 mm for repairs: for Thread Shank length Shoulder Ø 7Y9=6.5x6.7xM 7K=5 7K=6 7Y9=7x6.7xM 7K=5 7K=6 M 6.7 mm 6.5 mm M 6.7 mm 7 mm 7Y9=9.5x7.xM6 7K= M6 7. mm 9.5 mm 7Y9=0x7.xM6 7K= M6 7. mm 0 mm Practical recommendation: On worn joints, the tolerance can be reduced with the repair bolts. A suitable reamer is usually used for adaptation. With 7K9//// joint bars for children, the following shoulder screws can be used: 50A=x6xM 60 Ottobock Custom-Orthotics

63 KAFO system joints Free motion system joints 7B6 / 7B7 / 7B / 7B System knee joints Medial joint contoured bottom, straight top, straight lateral joint, free motion, with ball bearing, joint centre 6 mm to the posterior Side System width Length from joint centre upper/lower Material 7B6=L6 Left 6 mm / 8 mm Stainless steel Pair 7B6=R6 Right 6 mm / 8 mm Stainless steel Pair 7B6=L0 Left 0 mm / 8 mm Stainless steel Pair 7B6=R0 Right 0 mm / 8 mm Stainless steel Pair Straight free motion medial and lateral joint with ball bearing, joint centre 6 mm to the posterior System width Length from joint centre upper/lower Material 7B7=6 6 mm / 8 mm Stainless steel Pair 7B7=0 0 mm / 8 mm Stainless steel Pair Medial joint contoured bottom, straight top, straight lateral joint, free motion, with ball bearing, joint centre mm to the posterior Side System width Length from joint centre upper/lower Material 7B=L6 Left 6 mm / 8 mm Stainless steel Pair 7B=R6 Right 6 mm / 8 mm Stainless steel Pair 7B=L0 Left 0 mm / 8 mm Stainless steel Pair 7B=R0 Right 0 mm / 8 mm Stainless steel Pair Straight free motion medial and lateral joint with ball bearing, joint centre mm to the posterior System width Length from joint centre upper/lower Material 7B=6 6 mm / 8 mm Stainless steel Pair 7B=0 0 mm / 8 mm Stainless steel Pair Custom-Orthotics Ottobock 6

64 KAFO system joints Free motion system joints Accessories for 7B6, 7B7, 7B and 7B System extension assist with two rubber rings for 7Y System knee joints without lock 7Y5 System knee joints without lock Service parts for 7Y and 7Y5 8Z / 8Z Rubber ring for Outside Ø Inner Ø 8Z=0.8x.5 7Y 0.8 mm.5 mm 8Z=.6x8. 7Y.6 mm 8. mm 8Z=.0x.9 7Y5 mm.9 mm 8Z=6.8x7.7 7Y5 6.8 mm 7.7 mm 50S7 Oval head screw, slotted for Material 50S7=Mx Cover plate Stainless steel 50S Flat head screw 50S=Mx 50S79 Special screw To attach the extension assist 50S79=M5x.x6. 507S Serrated lock washer 507S=5. 509G Slide bearing 509G=5x7x5 for 7Y5 6 Ottobock Custom-Orthotics

65 KAFO system joints Free motion system joints Spare parts for 7B6, 7B7, 7B and 7B () Ball bearing 509K=5x6x () Oval head screw, slotted and partially threaded Material 50A6=x5xM5 Stainless steel () Phillips oval countersunk head screw 50T7=7.5x9xM5 Custom-Orthotics Ottobock 6

66 KAFO system joints SCO system joints 6 Ottobock Custom-Orthotics

67 KAFO system joints SCO system joints E-MAG Active Functional description The E-MAG Active is the first electronically controlled system knee joint with a locked stance phase and free swing phase that is not dependent on the ankle and sole of the foot. The principle of the E-MAG Active is as innovative as it is consistent: An intelligent sensor system measures the leg position while walking and controls the orthosis joint accordingly. Since the joint is activated independently of the ankle and sole of the foot, patients can take advantage of the functionality offered by the orthosis joint even if they do not have use of the ankle. Delivery condition The E-MAG Active joint system is supplied in a case with all required components. The case contains the entire matched system including a charger, a battery, and the required dummies for installation in an orthosis. The E-MAG is suitable for a body weight of up to 00 kg (with use of the 7B05 medial support). Unilateral use of the joint is possible up to 85 kg as long as there are no non-physiological deviations in the frontal and sagittal planes. Furthermore, the matching bars can be ordered as special accessories. Side Flexion angle 7B0N=L Left 5 7B0N=R Right 5 7B0N=L-7.5 Left 7.5 7B0N=R-7.5 Right 7.5 7B0N=L-0 Left 0 7B0N=R-0 Right 0 Certification is required for the E-MAG Active. Please contact your customer service/your regional contact person for this purpose. 66D58=EN 66DV 66D580=EN 66D57 66A=GB 67G69 67G60 Scope of delivery () Dummy for battery () Dummy for electronics () Dummy for battery receptacle () Dummy for electronics receptacle (5) Dummy for knee joint (6) Receptacle for battery (7) Lock unit for battery (7E0 connecting cable) (8) Receptacle for electronic control unit with connecting cable (9) Rechargeable battery (0) Control electronics () E-MAG Active knee joint () AC adapter for battery charger () Battery charger Installation instructions (not illustrated) Instructions for use (no illustrated) Quick start guide (not illustrated) Practical recommendation: Please observe the particularities of patient selection for stance phase controlled systems. Further information is found in the 66A* brochure for technicians and therapists. Custom-Orthotics Ottobock 65

68 KAFO system joints SCO system joints Accessories for the E-MAG Active 7LS= Unilateral system splint Length Width Thickness Material 7LS= 00 cm 7.8 mm 7 mm Aluminium 7LS= Lamination bar for conventional lamination resin or prepreg technique Length Width Thickness Material 7LS= 0 mm 7.8 mm 7 - mm Steel 7B05 Medial support Includes lamination dummy Max. body weight Ansatzschraube Material 7B05=L 00 kg Stainless steel 7B05=R 00 kg Stainless steel 67G6 605P8 Joint bar system for medial support (without illustration) Suitable for fabricating system splints, with rounded edges, strength approx. 00 N/mm² Length Width Thickness Material 605P8=0,000 mm 0 mm 5 mm Aluminium 605P8=0-05 mm 0 mm 5 mm Aluminium 66 Ottobock Custom-Orthotics

69 KAFO system joints SCO system joints Service sets for maintenance of the joint bearings 7BS00 Service set for 7BS00 E-MAG Active knee joint 7BS05 Service set for 7BS05 7B05 medial support joint Spare parts for E-MAG Active Designation 0G6=L E-MAG Active knee joint 0G6=R E-MAG Active knee joint 7X0N=L Dummy for knee joint 7X0N=R Dummy for knee joint 7B0 Replaceable battery 7L0 Battery charger 757L6- Power supply 7B Control electronics Designation Consisting of 7E 7Z 7E0 Electronics cable Receptacle for control electronics Connecting cable 7Z Receptacle set (electronics) Electronics receptacle Dummy for receptacle Dummy for electronics 7Z Receptacle set Battery receptacle Dummy for receptacle Dummy for battery Custom-Orthotics Ottobock 67

70 KAFO system joints SCO system joints 70K Free Walk orthosis The Free Walk orthosis is pre-fabricated for the first trial fitting according to your specifications. The tool kit and datasheets are needed for the measurements required for the fabrication of the orthosis. 66A=GB 66D5=GB 66T5=.GB 67H5 Side for patient weight up to Colour 70K=L-80-7 Left 80 kg Black 70K=R-80-7 Right 80 kg Black 70K=L-80-0 Left 80 kg Skin colour 70K=R-80-0 Right 80 kg Skin colour Side for patient weight up to Colour 70K=L-0-7 Left 0 kg Black 70K=R-0-7 Right 0 kg Black 70K=L-0-0 Left 0 kg Skin colour 70K=R-0-0 Right 0 kg Skin colour Delivery condition: as shown, but without foot part You may order a test orthosis on loan for a functional test on the patient upon request. Please contact your customer service/your regional contact person for this purpose! 68 Ottobock Custom-Orthotics

71 KAFO system joints SCO system joints Functional principle Stability in the stance phase: The orthotic knee joint locks automatically when the knee is extended prior to heel strike. The patient can then stand securely and put pressure on the leg during the stance phase. The Free Walk thus fulfills the functions of a locked orthosis. Decision-making aid One of the following prerequisites are given: Muscle strength of the hip extensors is to 5 or Muscle strength of the knee extensors to 5 or Knee hyperextension Knee stability in frontal plane At the present time, the patient does not possess enough muscle strength. In the course of rehabilitation, it can be expected that sufficient muscle strength will be regained. Knee stability in frontal plane Yes Valgus up to 5 In case of a valgus deformity up to 5, the 70D0 medial support has to be used. Yes Disengagement in the swing phase: The patient releases the orthotic knee joint by extending his or her knee prior to toe-off and allowing a dorsal flexion of the upper ankle joint. This allows him or her to flex the leg and let it swing through freely. up to 80 kg Body weight By removing the steel cable, the Free Walk can be turned into a locked orthosis. Patients with sufficient muscle strength can easily turn a locked orthosis back into a Free Walk orthosis. up to 0 kg 70K=L/R80 Free Walk 70K=L/R80-0 Free Walk skin colour 70K=L/R80-7 Free Walk black 70K=L/R0 Free Walk 70K=L/R0-0 Free Walk skin colour 70K=L/R0-7 Free Walk black Custom-Orthotics Ottobock 69

72 KAFO system joints SCO system joints Information for the ordering process Take the patient measurements (note the 66T5= technical information). Please also complete the forms (patient data and measurement form, measurement forms for the outline sketch) included in the 70W Free Walk orthosis tool kit (may be obtained on loan for initial fittings). Please submit all forms to Ottobock Service Fabrication. Ottobock Service Fabrication will fabricate a Free Walk orthosis for you, and usually ships it after 5 working days. You receive a Free Walk orthosis with an exact fit, supporting a harmonious gait pattern and secure stance. 66S=5.0GB (Info sheet) 6T (measurement taking forms for an Ottobock Free Walk orthosis) 67F6=GB Patient data and measurement form x 67F0= measurement form for outline sketch 66T5=.GB technical information 66D8=GB (information for doctors) 66D8=GB (patient information) 66A (therapeutic application) 66D5=GB (product information) 70 Ottobock Custom-Orthotics

73 KAFO system joints SCO system joints Accessories for 70K 70D50 Triple control Extension of the indication through greater knee joint functionality Locked function Free function Free Walk function for patient weight up to Colour 70D50=L 80/0 kg Black 70D50=R 80/0 kg Black 67G7 67G7= 67G7= 70D0 Medial knee guide Extension of the indication 5 more valgus deformity can be fitted for patient weight up to Colour 70D0=0-7 0 kg Black Set 70D0= kg Black Set 67G9 Spare parts for 70K 70D80 / 70D0 Foam pads for Colour 70D80=-0 70K=80 Skin colour 70D80=-0 70K=80 Skin colour 70D80=-7 70K=80 Black 70D80=-7 70K=80 Black 70D0=-0 70K=0 Skin colour 70D0=-0 70K=0 Skin colour 70D0=-7 70K=0 Black 70D0=-7 70K=0 Black Custom-Orthotics Ottobock 7

74 KAFO system joints SCO system joints 70Z Hook-and-loop strap for Material Colour 70Z= K=80/=0 Polyamide skin colour 70Z= K=80/=0 Polyamide black 70Z= K=80/=0 Polyamide skin colour 70Z= K=80/=0 Polyamide black 70D Y-hook-and-loop for Width Colour 70D=8-0 70K=80/=0 8 mm skin colour 70D=8-7 70K=80/=0 8 mm black Practical recommendation: Close before washing to protect the closure and/or other items in the wash. 70D7 Pad button Used for 70D7 70D0 Strap guide loop for pad button 70D0 Strap guide loop for pad button Colour 70D0=0 skin colour 70D0=7 black 70D8 Strap guide loop with tube connection for Colour 70D8= K=80 Black 70D8=0-7 70K=0 Black 70D8= K=80 Skin colour 70D8=0-0 70K=0 Skin colour 70Z0 Joint protector for Colour 70Z0=7 70K=L/R0/80 Black 70Z0=0 70K=L/R0/80 Skin colour 7 Ottobock Custom-Orthotics

75 KAFO system joints SCO system joints 70Z99 Maintenance set for lock for 70Z99= 70K Set 70X Maintenance set for Free Walk for 70X= 70K Set 70X6 Adjustable ankle joint with universal foot part Side Scope of delivery 70X6=L Left Set x 70C=L x 70D8 x 50F7=M6X0- x 70F x 70F7 x 50T5=MX- x 70D6 70X6=R Right Set x 70C=R x 70D8 x 50F7=M6X0- x 70F x 70F7 x 50T5=MX- x 70D6 Custom-Orthotics Ottobock 7

76 KAFO system joints SCO system joints Spare parts for 70X6 () Ankle joint, lower part Side 70C=L Left 70C=R Right () Threaded plate 70D8 () Screw with flattened half-round head 50F7=M6X0- for () Foot upper part 70F (5) Foot lower part 70F7 (6) Oval head flange screw 50T5=MX- Pair (7) Ankle setting nut 70D6 Pair Accessories for measuring 70W Tool kit for 70W=M Measuring and fine-tuning the Free Walk orthosis 70W Contour scriber 70W 7 Ottobock Custom-Orthotics

77 KAFO system joints SCO system joints 70W Tension band 70W 70W8 Ankle and knee support 70W8 7B Spring-tensioned measuring tape 7B Length 500 mm 70W0 Drilling template 70W0 70W Mounting aid 70W 70W Pad holder bending help 70W= 70W= Custom-Orthotics Ottobock 75

78 KAFO system joints SCO system joints 70W Frontal contour bending tool 70W 70W Aluminium threaded jaws 70W 70W8 Bending irons 70W8 70W9 Calliper 70W9 70W6 Gluteal pad 70W6 70W7 Knee pad, roll 70W7 76 Ottobock Custom-Orthotics

79 KAFO system joints Waterproof orthoses Aqualine orthosis system The Aqualine orthosis system is a waterproof walking aid for orthosis wearers. Offering the user the greatest possible safety with simultaneous freedom of movement. The waterproof versions of the CarbonIQ knee and ankle joints form the heart of the Aqualine orthosis system. The individual components are resistant to corrosion, and contact with chlorine, salt water or soap does not impair their functionality. Custom-Orthotics Ottobock 77

80 KAFO system joints Waterproof orthoses () Hook-and-loop strap Length Material Colour 70Z= mm Polyamide black () Joint bar system for medial support Length Width Thickness Material 605P8=0,000 mm 0 mm 5 mm Aluminium () Waterproof CarbonIQ knee joint with wedge lock Side Max. body weight Material 7PK=L0-WR Left 00 kg Fibre-reinforced plastic 7PK=R0-WR Right 00 kg Fibre-reinforced plastic Pair Pair () Antibacterial ThermoLyn PP-H Width Colour 66T0=,000 mm natural colour (5) Flat head screw 50S8=Mx8 (6) Waterproof CarbonIQ ankle joint Max. body weight Material 7PA=0-WR 00 kg Fibre-reinforced plastic Pair (7) Foot stirrup Material 7PF Stainless steel (8) Outsole Side Material 9F8=L Left Rubber plate with crepe profile 9F8=R Right Rubber plate with crepe profile Practical recommendation: All components of a waterproof walking aid should be waterproof and easily washable. We generally recommend the use of a full-surface non-skid sole or a bathing shoe, as well as the use of a knee joint with lock. We recommend the use of antibacterial materials. The waterproof walking aid should minimise skin contact. 78 Ottobock Custom-Orthotics

81 KAFO system joints Waterproof orthoses Spare parts for 7PA=0-WR () Set screw 506G=M6x () Stop pin 506A7=5M6x0 () Service set Scope of delivery 9PA Set x 50S8=M6X x 0Y5 x 509G0=XX x 0Y () Set screw 506G=Mx (5) Bearing ball Material 509Y=5.0 Stainless steel (6) Stop pin (small) 506A5=.5M6x8 (7) Compression spring 5D8=.7x- (8) Adjustment Aid Scope of delivery 9PK Set x 50T8=M6X5 x 0Y6 Custom-Orthotics Ottobock 79

82 KAFO system joints Waterproof orthoses Spare parts for 7PK=L/R0-WR () Service set Scope of delivery 9PK Set x 50S6=.0X x 0Y06 x A8= x 5D5= x A x 0Y07 () Service set Scope of delivery 9PK Set x 509G0=X6X5 x 0Y0 x 50T9=M6X8 x 0Y09 () Adjustment Aid Scope of delivery 9PK Set x 50T8=M6X5 x 0Y6 () Set screw 506G=Mx 80 Ottobock Custom-Orthotics

83 KAFO system joints Correction system joints 7BK Correction system joints Static joints for positioning orthoses Side System width Dynamic unit Material Medial support 7BK=L Left 0 mm 7BK=L Aluminium 7BK=8 7BK=R Right 0 mm 7BK=R Aluminium 7BK=8 7BK=L Left 6 mm 7BK=L Aluminium 7BK=8 7BK=R Right 6 mm 7BK=R Aluminium 7BK=8 7BK=L Left mm 7BK=L Aluminium 7BK= 7BK=R Right mm 7BK=R Aluminium 7BK= 7BK=L Left mm 7BK=L Aluminium 7BK= 7BK=R Right mm 7BK=R Aluminium 7BK= Delivery condition: The joint is supplied with an adjustment wrench. size recommendation Body height Wrist joint Elbow joint Knee joint Ankle joint Child up to m =L/R =L/R =L/R =L/R Child -.0 m =L/R =L/R =L/R =L/R Adults up to.60 m Adults m =L/R =L/R =L/R =L/R =L/R =L/R =L/R =L/R Attention: this information constitutes recommendations only. The correct size for the respective patient has to be determined and specified by the orthotist. The joints are used individually or in pairs depending on the application. We recommend to always use a medial support, e.g. an integrated plastic joint. In case of knee and ankle joints, bilateral fitting (in pairs) is mandatory. The left/right side indications refer to application of the joints on the wrist, knee joint or ankle joint. Due to anatomical characteristics, the sides must be reversed for elbow applications (right to left and left to right). Custom-Orthotics Ottobock 8

84 KAFO system joints Correction system joints Accessories for 7BK 7BK Dynamic unit for correction system joint The 7BK dynamic unit is available for all four sizes of the 7BK static correction system joint and, depending on the joint size, offers a maximum spring force of approx. 0 Nm. Use of the 7BK dynamic unit allows for extension or flexion yielding, depending on the joint and indications. Spring force is used to slowly correct the joint back into the desired position. 66D9=EN 66D57 67G8 The tension is continuously adjustable, allowing for individual dynamic treatment of contractures. for Max. tension 7BK=L 7BK=L ~ 0 Nm 7BK=R 7BK=R ~ 0 Nm 7BK=L 7BK=L ~ 6 Nm 7BK=R 7BK=R ~ 6 Nm 7BK=L 7BK=L ~ 6 Nm 7BK=R 7BK=R ~ 6 Nm 7BK=L 7BK=L ~ Nm 7BK=R 7BK=R ~ Nm 7BK Medial support for correction system joint Material 7BK= Aluminium 7BK=8 Aluminium Please note that the size and side of the static and dynamic units have to be identical. Selection of Ottobock system joint bars matching the joints 7F5 Side bar for Length Width Thickness Material 7F5=xx0 7F5=xx0 7BK=L 7BK=R 7BK=L 7BK=R 0 mm mm mm Aluminium 0 mm mm mm Aluminium 66A0=GB 605P8 Light metal profile bar Suitable for fabricating system splints, with rounded edges, strength approx. 00 N/mm² for Length Width Thickness Material 605P8=6 7BK=L 7BK=R 605P8=0 7BK=L 7BK=R,000 mm 6 mm 5 mm Aluminium,000 mm 0 mm 5 mm Aluminium 8 Ottobock Custom-Orthotics

85 KAFO system joints Correction system joints Spare parts for 7BK () Upper joint section for Side 7X=L 7BK=L Left 7X=R 7BK=R Right 7X=L 7BK=L Left 7X=R 7BK=R Right 7X=L 7BK=L Left 7X=R 7BK=R Right 7X=L 7BK=L Left 7X=R 7BK=R Right () Lower joint section for Side 7U=L 7BK=L Left 7U=R 7BK=R Right 7U=L 7BK=L Right 7U=R 7BK=R Right 7U=L 7BK=L Left 7U=R 7BK=R Right 7U=L 7BK=L Left 7U=R 7BK=R Right () Lock cover for Side 0Y5=L 7BK=L Left 0Y5=R 7BK=R Right 0Y5=L 7BK=L Left 0Y5=R 7BK=R Right 0Y5=L 7BK=L Left 0Y5=R 7BK=R Right 0Y5=L 7BK=L Left 0Y5=R 7BK=R Right () Joint nut for 0Y56= 7BK=L, 7BK=R 0Y56= 7BK=L, 7BK=R 0Y56= 7BK=L, 7BK=R 0Y56= 7BK=L, 7BK=R (5) Gear wheel for 0Y57= 7BK=L, 7BK=R 0Y57= 7BK=L, 7BK=R 0Y57= 7BK=L, 7BK=R 0Y57= 7BK=L, 7BK=R Custom-Orthotics Ottobock 8

86 KAFO system joints Correction system joints (6) Set wheel with lever for 0Y= 7BK=L, 7BK=R, 7BK=L, 7BK=R, 7BK=L, 7BK=R 0Y= 7BK=L, 7BK=R (7) Phillips flat head screw for Material 50T9=MX6-7BK=L, 7BK=R Stainless steel 50T9=MX- 7BK=L, 7BK=R, 7BK=L, 7BK=R Stainless steel 50T9=MX- 7BK=L, 7BK=R Stainless steel (8) Washer set for 7BK=S- 7BK=L, 7BK=R 7BK=S- 7BK=L, 7BK=R 7BK=S- 7BK=L, 7BK=R 7BK=S- 7BK=L, 7BK=R (9) Phillips oval countersunk head screw for Material 50T7=7.5xxM5 7BK=L, 7BK=R, 7BK=L, 7BK=R Stainless steel for Material 50S86=MX8 7BK=L, 7BK=R, 7BK=L, 7BK=R Stainless steel 8 Ottobock Custom-Orthotics

87 Notes Custom-Orthotics Ottobock 85

88 Materials and accessoires 86 Ottobock Custom-Orthotics

89 Materials and accessoires Materials and accessoires In this section, you will find a selection of materials, tools and accessories that are essential for modern orthosis fabrication. Please note that this catalogue does not contain all tools and materials that can be used for the fabrication of orthoses and prostheses. For further tools and materials please refer to our catalogues "Orthotic-Prosthetic Materials" (66K) and "Planning and Equipping" (66K0). Bars and stirrups Equipment Materials Thermoplastics... 0 Carbon materials... 0 Resin Custom-Orthotics Ottobock 87

90 Materials and accessoires Bars and stirrups 7B58 Foot stirrup Thickness Bar width Stirrup length Head Ø Material 7B58=6x.5x5.5 mm 6 mm 5 mm 6 mm Stainless steel 7B58=8xx65 mm 0 mm 65 mm 8 mm Stainless steel 7B58=0xx65 mm 0 mm 65 mm 0 mm Stainless steel 7B65 Shoe stirrup Article number 7B65=6x.5 x 5 7B65= 8xx65 7B65= 0xx65 System width Thickness Channel width Head Ø Length from joint centre Material 6 mm.5 mm 9 mm 6 mm 5 mm Stainless steel 0 mm mm mm 8 mm 65 mm Stainless steel 0 mm mm mm 0 mm 65 mm Stainless steel 7B07 Foot stirrup with dorsal stop to be established by filing, and 0 plantar flexion System width Thickness Length from joint centre Material 7B07=5x.5 6 mm.5 mm 5 mm Stainless steel 7B07=65x 0 mm mm 65 mm Stainless steel 7Y8 System lamination bar System lamination bars are glued with 66W8 Ottobock special adhesive. System width Length Thickness Material Package contents 7Y8=6x80 6 mm 80 mm mm Stainless steel pcs. 7Y8=0x80 0 mm 80 mm mm Stainless steel pcs. 7Y8=6x00 6 mm 00 mm mm Stainless steel 7Y8=0x00 0 mm 00 mm mm Stainless steel Attention! The system lamination bars always have to be used in pairs in the leg orthosis. Unilateral use can cause the lamination bar to break due to overloading. 88 Ottobock Custom-Orthotics

91 Materials and accessoires Bars and stirrups 7B8 System side bar set flat, consisting of two 7B and 7B=T upper side bars and one each, left and right, 7B5 and 7B5=T lower side bars, with 66W8 Ottobock special adhesive System width Thickness Material 7B8=6 6 mm mm Stainless steel Set 7B8=0 0 mm mm Stainless steel Set Individual components of 7B8 () 7B Upper side bar Straight free-motion medial and lateral joint with ball bearing, pivot point 6 mm to the posterior System width Length Thickness 7B=6 6 mm 0 mm mm 7B=0 0 mm 0 mm mm () 7B5 Lower side bar Side System width Length Thickness 7B5=L6 Left 6 mm 50 mm mm 7B5=R6 Right 6 mm 50 mm mm 7B5=L0 Left 0 mm 50 mm mm 7B5=R0 Right 0 mm 50 mm mm 67G 7B9 System side bar set consisting of two upper side bars and one each, left and right, lower side bars, with Ottobock special adhesive System width Thickness Material 7B9=6 6 mm 5 mm Aluminium Set 7B9=0 0 mm 5 mm Aluminium Set Individual components of 7B8 () 7B6 Upper side bar Length Thickness System width 7B6=6 0 mm 5 mm 6 mm 7B6=0 0 mm 5 mm 0 mm () 7B7 Lower side bar Side Thickness System width 7B7=L6 Left 5 mm 6 mm 7B7=R6 Right 5 mm 6 mm 7B7=L0 Left 5 mm 0 mm 7B7=R0 Right 5 mm 0 mm 67G78 Custom-Orthotics Ottobock 89

92 Materials and accessoires Equipment 7A6 Orthotic alignment aid for three-dimensional alignment of leg orthoses and positioning of knee and ankle joint points on a plaster negative or plaster positive. Dimensions WxDxH Weight 7A6 70 x 80 x 770 mm kg 67H6 7A7 Pivot point adjustment aid to determine and establish the knee and ankle pivot point and reference lines on a plaster positive or negative 7A7 Material Stainless steel 67G7 67H65 7A8 Knee pivot gauge to determine the comprise pivot point according to Nietert, incl. rotation indicator Material To be used for 7A8 Stainless steel To determine the compromise pivot axis according to Nietert (60:0 graduation) 7A9 Foot plaster casting aid for an accurate foot impression with heel height and toe pitch on the forefoot 7A9 Material Plastic/stainless steel 67G6 90 Ottobock Custom-Orthotics

93 Materials and accessoires Equipment 79F6=* Silicone sanding cones 79F6=5/8 79F6=M6 Thread 5/8 M6 Weight To be used for Scope of delivery 0.66 kg Polishing and rounding edges of thermoplastic materials -piece set: Silicone sanding cone, conical Silicone sanding cone, conical and pointed Silicone sanding cone, round Silicone sanding cone, round with grooves Custom-Orthotics Ottobock 9

94 Materials and accessoires Equipment 7R6 Orthotic joint alignment set 7R6 To be used for As an aid for lower limb orthosis fabrication, suitable for the "structural orthosis fabrication" technique according to a drawing and for the lamination resin and deep-drawing techniques according to a plaster model consisting of () 7Y55 Alignment axis 7Y55 Material Aluminium () 7Y70 Parallel adapter Width Material 7Y70=50 50 mm Aluminium 7Y70=80 80 mm Aluminium () 7Y56 Adjustment adapter Size Material 7Y56= Stainless steel 7Y56= Stainless steel 7Y56= Stainless steel 7Y56= Stainless steel () 7Y7 Allen screw with collar 7Y7 9 Ottobock Custom-Orthotics

95 Materials and accessoires Equipment (5) 50A Shoulder screw for Thread 50A=X6XM 7Y56= adjustment adapter M 50A=x7xM 7Y56= adjustment adapter M 50A=X8XM6 7Y56= adjustment adapter M6 50A=x9xM6 7Y56= adjustment adapter M6 The article number of the matching shoulder screw for the joint dummy of the 7LK Unilateral Knee Joint is 0Y89. (6) 709S0=* Allen key Side piece length Material 709S0=.5 57 x 0 mm Nickel-plated CV-steel 7Y7=* Locating bolt for For system width Material 7Y7= Alignment adapter: 7Y56=* System knee joints: 7B6, 7B8, 7B90, 7B7, 7B6 7Y7= Alignment adapter: 7Y56=* System knee joints: 7B6, 7B8, 7B90, 7B7, 7B6 6 mm Stainless steel 0 mm Stainless steel 7Y6 Positioning aid for Material 7Y6 7Y56=* alignment adapter Stainless steel 7Y8 Adapter sleeve The adapter sleeves are slid onto the 7Y55 alignment axis and positioned in the plaster negative. Adapter sleeve made of rigid foam for receiving the 7Y56 adjustment adapters in the plaster positive. The adapter sleeves are slid onto the 7Y55 alignment axis and positioned in the plaster negative. Length Material Package contents 7Y8 90 mm 9 cm Rigid foam pcs. 7Y9 Shoulder screw set matching 7Y56= adjustment adapter for Package contents 7Y9 Knee joint bars 7M0 through 7M pairs Custom-Orthotics Ottobock 9

96 Materials and accessoires Equipment 7S=* Bending iron 7S=6X 7S=8X6 7S=9X7 Version Straight jaws Material CV steel Jaw opening and 6 mm 6 and 8 mm 7 and 9 mm Length 5 mm 7S Bending iron Material For bar widths Length 7S Tool steel, high-alloyed and 6 mm 500 mm 7S Bending pusher set Material Package contents To be used for Scope of delivery 7S Steel pc. Use in vice pc. 9 Ottobock Custom-Orthotics

97 Materials and accessoires Materials Y78 Hook-and-loop closure With strap guide loop and bracket Length Width Colour Y78=5-0 0 mm 5 mm skin colour Y78=0-0 0 mm 0 mm skin colour Y78=8-0 0 mm 8 mm skin colour Y78= mm 50 mm skin colour Length Width Colour Y78=5-50 mm 5 mm red Y78=0-50 mm 0 mm red Y78=8-50 mm 8 mm red Y78=50-50 mm 50 mm red Length Width Colour Y78=5-50 mm 5 mm yellow Y78=0-50 mm 0 mm yellow Y78=8-50 mm 8 mm yellow Y78=50-50 mm 50 mm yellow Length Width Colour Y78= mm 5 mm blue Y78= mm 0 mm blue Y78= mm 8 mm blue Y78= mm 50 mm blue Length Width Colour Y78= mm 5 mm white Y78= mm 0 mm white Y78= mm 8 mm white Y78= mm 50 mm white Length Width Colour Y78= mm 5 mm black Y78= mm 0 mm black Y78= mm 8 mm black Y78= mm 50 mm black Practical recommendation: Close before washing to protect the closure and/or other items in the wash. Custom-Orthotics Ottobock 95

98 Materials and accessoires Materials 70D Y-hook-and-loop For quick fabrication of straps, e.g., directly on the patient for Width Colour Quantity unit 70D=8-0 70K=80/=0 8 mm skin colour 70D=8-7 70K=80/=0 8 mm black Practical recommendation: Close before washing to protect the closure and/or other items in the wash. 70Z Hook-and-loop strap Made especially for FreeWalk orthosis for Length Material Colour Quantity unit 70Z= K=80/=0 00 mm Polyamide skin colour 70Z= K=80/=0 00 mm Polyamide black 70Z= K=80/=0 600 mm Polyamide skin colour 70Z= K=80/=0 600 mm Polyamide black Practical recommendation: Close before washing to protect the closure and/or other items in the wash. 6P5 Padding tape For hook-and-loop closures, compatible with hook-and-loop Length Width Colour 6P5= 985 mm 65 mm Black 6P5= 985 mm 55 mm Black 96 Ottobock Custom-Orthotics

99 Materials and accessoires Materials 6Z Micro hook-and-loop, self-adhesive Width Colour 6Z= mm white Please specify length when ordering. Practical recommendation: For better adhesion of the micro hook-and-loop on the orthosis, apply some contact adhesive to the gluing surface on the orthosis and slightly warm the self-adhesive surface of the micro hook-and-loop with the hot air gun. 66K8 Plastic band Plastic tape for sealing, filling and protection during work with lamination resin, e.g., for orthotic joints Length Width Thickness Colour 66K8=0xx0 0 m 0 mm mm Grey Custom-Orthotics Ottobock 97

100 Materials and accessoires Materials 67H68 67R Thermoprepregs PE/PP Thermoprepregs consist of thermoplastic material (PE or PP) with unidirectional continuous fibreglass threads (see illustration). The fibreglass rovings are blended into the cover layers of the profile and unevenly distributed along either side. The heat-weldable side contains a higher proportion of fibres than the opposite side to counteract distortion of the sheet material. This side can be easily recognised by its mm edge radius and the "Ottobock" logo. Application example Prior to vacuum forming, pull stockinettes such as 8A nylon sock on a roll or 6T perlon stockinette over the plaster model. Cut 67R=PE/PP thermoprepreg and thermoplastic material to the required size and place into the pre-heated oven until appropriately heated for the vacuum forming process (e.g. ThermoLyn PP-H becomes transparent). Remove the tailored thermoprepreg sheeting from the oven and place it on the model in the required position. While doing so, keep the oven door closed to prevent the tailored thermoplastic sheeting from cooling. Immediately after shaping the thermoprepreg, vacuum form the thermoplastic sheeting over it. Illustration showing cross section of the thermoplastic prepreg: Length Width Order by 67R=PE,00 mm 0 mm Package of 67R=PP,00 mm 0 mm Package of 98 Ottobock Custom-Orthotics

101 Materials and accessoires Materials 67S7 Plastazote Thermoformable at 0 C/0 F on a hotplate or in a convection oven Length Width Thickness Colour 67S7=,000 mm,000 mm mm Skin colour 67S7=,000 mm,000 mm mm Skin colour 67S7=,000 mm,000 mm mm Skin colour 67S7=5,000 mm,000 mm 5 mm Skin colour 67S7=6,000 mm,000 mm 6 mm Skin colour 67S7=7,000 mm,000 mm 7 mm Skin colour 67S7=8,000 mm,000 mm 8 mm Skin colour 67S7=0,000 mm,000 mm 0 mm Skin colour 67S7=,000 mm,000 mm mm Skin colour 67S7=5,000 mm,000 mm 5 mm Skin colour 67S7=7-B,000 mm,000 mm 7 mm Skin colour 67S7=8,000 mm,000 mm 8 mm Skin colour 67S7=0,000 mm,000 mm 0 mm Skin colour 67S7=0,000 mm,000 mm 0 mm Skin colour 67S7=5,000 mm,000 mm 5 mm Skin colour 67S9 / 67S / 67S / 67S Evazote Other sheet thicknesses available upon request. 66F95=D Length Width Thickness Colour 67S9=,000 mm,000 mm mm White 67S9=,000 mm,000 mm mm White 67S9=5,000 mm,000 mm 5 mm White 67S9=6,000 mm,000 mm 6 mm White 67S9=8,000 mm,000 mm 8 mm White 67S9=0,000 mm,000 mm 0 mm White 67S9=,000 mm,000 mm mm White 67S9=0,000 mm,000 mm 0 mm White Length Width Thickness Colour 67S=,000 mm,000 mm mm Red 67S=,000 mm,000 mm mm Red 67S=,000 mm,000 mm mm Red 67S=5,000 mm,000 mm 5 mm Red 67S=6,000 mm,000 mm 6 mm Red 66F95=GB Length Width Thickness Colour 67S=,000 mm,000 mm mm Blue 67S=,000 mm,000 mm mm Blue 67S=,000 mm,000 mm mm Blue 67S=5,000 mm,000 mm 5 mm Blue 67S=6,000 mm,000 mm 6 mm Blue 67S=8,000 mm,000 mm 8 mm Blue 67S=0,000 mm,000 mm 0 mm Blue 67S=5,000 mm,000 mm 5 mm Blue Plastazote and Evazote are registered trademarks of Zotefoams. Custom-Orthotics Ottobock 99

102 Materials and accessoires Materials Length Width Thickness Colour 67S=,000 mm,000 mm mm Yellow 67S=,000 mm,000 mm mm Yellow 67S=,000 mm,000 mm mm Yellow 67S=5,000 mm,000 mm 5 mm Yellow 67S=6,000 mm,000 mm 6 mm Yellow 6F6 SpaceTex padding fabric For soft inner sockets, density 0.0 g/cm³, hardness 0 Shore A, thermoformable between 0 and 70 C/8 and 8 F on a hotplate or in a convection oven, washable, skin-friendly For manufacturing reasons, the plates can either be smooth on one side and rough on the other, or smooth on both sides. Length Width Thickness Colour 6F6=-7 m,00 mm mm black 6F6=-7 m,00 mm mm black 6F6=5-7 5 m,00 mm mm black 66F95=GB Practical recommendation: Can be combined with 6Z micro hook-and-loop. Apply 66W7 CP contact adhesive to the micro hook-and-loop and fasten it to the surface to be padded. 6P Terry cloth padding fabric For soft inner sockets, density 0.0 g/cm³, hardness 0 Shore A, thermoformable between 0 and 70 C/8 and 8 F on a hotplate or in a convection oven, washable, skin-friendly For manufacturing reasons, the plates can either be smooth on one side and rough on the other, or smooth on both sides. 66F95=GB Length Width Thickness Colour 6P= m,60 mm mm Blue 6P= m,60 mm mm Blue 6P=5 5 m,60 mm mm Blue 6P=0 0 m,60 mm mm Blue Length Width Thickness Colour 6P=H m,60 mm mm skin colour 6P=H m,60 mm mm skin colour 6P=H5 5 m,60 mm mm skin colour 6P=H0 0 m,60 mm mm skin colour 00 Ottobock Custom-Orthotics

103 Materials and accessoires Materials Length Width Thickness Colour 6P=S m,60 mm mm black 6P=S m,60 mm mm black 6P=S5 5 m,60 mm mm black 6P=S0 0 m,60 mm mm black Practical recommendation: Can be combined with 6Z micro hook-and-loop. Apply 66W7 CP contact adhesive to the micro hook-and-loop and fasten it to the surface to be padded. Custom-Orthotics Ottobock 0

104 Materials and accessoires Thermoplastics 66F65=GB 66D00=GB 66D9=GB 66D695=EN 66T95 ThermoLyn PE 00 Hard polyethylene with low shrinkage, processing temperature 80 C/56 F (heating plate), 65 C/9 F (convection oven), 65 C/9 F (infrared oven) Length Width Thickness Colour 66T95=,000 mm,000 mm mm natural colour 66T95=,000 mm,000 mm mm natural colour 66T95=,000 mm,000 mm mm natural colour 66T95=5,000 mm,000 mm 5 mm natural colour 66T95=6,000 mm,000 mm 6 mm natural colour 66T95=8,000 mm,000 mm 8 mm natural colour 66T95=0,000 mm,000 mm 0 mm natural colour 66T95=,000 mm,000 mm mm natural colour 66T0 ThermoLyn PP-C The new 66T0 ThermoLyn polypropylene copolymer is a thermoplastic sheet material that uses copolymerisation to combine the benefits of polypropylene and the toughness of polyethylene. The polypropylene copolymer (PP-C) obtained in this way shows considerably increased impact strength in comparison with a homopolymer polypropylene (PP-H), especially at low temperatures. 66F65=GB 66D00=GB Length Width Thickness Colour 66T0=,000 mm,000 mm mm natural colour 66T0=,000 mm,000 mm mm natural colour 66T0=,000 mm,000 mm mm natural colour 66T0=5,000 mm,000 mm 5 mm natural colour 66T0=6,000 mm,000 mm 6 mm natural colour 66T8 ThermoLyn clear The processing temperature for heating plates, convection and infrared ovens is 65 C/9 F. The transparency of the check socket made of ThermoLyn clear facilitates precise verification of the fit and skin discolouration on the residual limb. By warming the socket, it is possible to reform the thermoplastic at, for example, pressure points. 66F65=GB 66D00=GB 66D9=GB 66D695=EN Length Width Thickness Colour 66T8=8 00 mm 00 mm 8 mm clear 66T8=0 00 mm 00 mm 0 mm clear 66T8= 00 mm 00 mm mm clear 66T8=5 00 mm 00 mm 5 mm clear 66T8=0 00 mm 00 mm 0 mm clear 66T8=50x05x,50 mm,05 mm mm clear 66T8=50x05x,50 mm,05 mm mm clear 66T8=50x05x6,50 mm,05 mm 6 mm clear Practical recommendation: For working edges we recommend hot air or 6A80 SuperSkin cleaning agent. 0 Ottobock Custom-Orthotics

105 Materials and accessoires Thermoplastics 66T0 Antibacterial ThermoLyn PP-H Length Width Thickness Colour 66T0=,000 mm,000 mm mm natural colour 66T0=,000 mm,000 mm mm natural colour 66T0=,000 mm,000 mm mm natural colour 66T0=5,000 mm,000 mm 5 mm natural colour 66T0=6,000 mm,000 mm 6 mm natural colour 66T0=8,000 mm,000 mm 8 mm natural colour 66T0=0,000 mm,000 mm 0 mm natural colour 66F65=GB 66D695=EN 66D9=GB 66D00=GB 66T0=,000 mm,000 mm mm natural colour 66T0=5,000 mm,000 mm 5 mm natural colour Practical recommendation: The low impact value means great care must be taken during machining in order to avoid brittle fractures (stress concentration). Custom-Orthotics Ottobock 0

106 Materials and accessoires Carbon materials 66B Carbon-fibreglass webbing Unidirectional, easy to shape, drapable Length Width 66B=5x5 5 m 5 mm 66B=5x0 0 m 5 mm 66B=5x0 0 m 5 mm 66B=5x50 50 m 5 mm 66B=50x5 5 m 50 mm 66B=50x0 0 m 50 mm 66B=50x0 0 m 50 mm 66B=50x50 50 m 50 mm 66B7 Carbon fibre mesh For partial high-strength laminate reinforcements in lower limb prostheses as well as in orthoses. Processability including the woven edge is advantageous (edges are not sewn), because masking is not necessary. Length Width 66B7=50x m 50 mm 66B7=50x5 5 m 50 mm 66B7=50x0 0 m 50 mm 66B7=00x m 00 mm 66B7=00x5 5 m 00 mm 66B7=00x0 0 m 00 mm 66B7=00x m 00 mm 66B7=00x5 5 m 00 mm 66B7=00x0 0 m 00 mm 66G Carbon fibre mesh For partial high-strength laminate reinforcements Length Width 66G= m,00 mm 66G= m,00 mm 66G=5 5 m,00 mm 66G=0 0 m,00 mm 66G=0 0 m,00 mm 66G=0 0 m,00 mm 67G5 All Ottobock reinforcement materials are photographed from top to bottom. Lengthwise (warp), crosswise (weft) 0 Ottobock Custom-Orthotics

107 Materials and accessoires Resin 67H9 Orthocryl lamination resin 80:0 PRO Net contents 67H9= kg 67H9= kg 67H9=5 5 kg Resin 00 : hardener - : colour paste 6K filling set is available for containers of 5 kg and over. Danger 66F5=DE Practical recommendation: For sheet casting, use only 66F PVA film or 99B8 PVA bags. 6K filling set is available for containers of 5 kg and over. In order to ensure that all air bubbles are eliminated from the reinforcement, the following has to be observed: Make sure that the plaster model is under a constant vacuum from the outset. Cast the resin all at once, and not gradually, which is done with conventional resins. 67P7 Hardening powder For Orthocryl resins, with g measuring spoon 67P7= P7=0.50 Net contents 0.0 kg 0.5 kg Danger Practical recommendation: Applies to all Orthocryl resins: add max. % 67P7 hardening powder. Custom-Orthotics Ottobock 05

108 Materials and accessoires Resin 99B8 PVA bags For working with Orthocryl and polyester lamination resins 0 per package Length Width Thickness Order by 99B8=60xx 60 cm cm 0.08 mm 0 pcs. 99B8=70x9x5 70 cm 9 cm 0.08 mm 0 pcs. 99B8=70x7x5 70 cm 7 cm 0.08 mm 0 pcs. 99B8=00x9x5 00 cm 9 cm 0.08 mm 0 pcs. 99B8=00x6x5 00 cm 6 cm 0.08 mm 0 pcs. 99B8=00x0x5 00 cm 0 cm 0.08 mm 0 pcs. 99B8=00x6x5 00 cm 6 cm 0.08 mm 0 pcs. 99B8=0x50x0 0 cm 50 cm 0.08 mm 00 pcs. 99B8=0x9x5 0 cm 9 cm 0.08 mm 0 pcs. 99B8=0xx5 0 cm cm 0.08 mm 0 pcs. 99B8=0x6x5 0 cm 6 cm 0.08 mm 0 pcs. 06 Ottobock Custom-Orthotics