huwilift-swing huwilift-slide

Transcription

1 Installation Instructions huwilift-swing huwilift-slide HUWIL-WERKE GmbH Möbelschloß- und Beschlagfabriken D Ruppichteroth Tel.: +49/2295/7-0 Fax: +49/2295/7-200 internet:

2 2 huwilift-swing/slide

3 Foreword Dear Customer, By choosing the swing/slide, you have opted for a fitting solution that is technically very advanced and mechanically very efficient. Your swing/slide is manufactured on our premises with extreme care and precision and is going through numerous quality and safety checks in order to ensure that it operates smoothly and safely. But you yourself can also make an important contribution towards ensuring that you remain happy with your swing/slide for a long time. 1. IMPORTANT SAFETY NOTE The installation must be carried out in accordance with the assembly instructions; otherwise there is a risk of injury. 2. This swing/slide may solely be employed for its intended use as a lid-stay fitting for living room and kitchen furniture according to the indicated lifting capacity. Any use that goes beyond this criteria is considered as a not designated use. The manufacturer is not responsible for any damage resulting from such a form of use. All risks associated with the not designated use of the fitting are borne by the operator alone. 3. The observance of the assembly instructions as prescribed by the manufacturer also form part of the designated use. 4. To be fully respected are also all applicable general regulations and legal provisions also those that apply in the operator s country as well as all applicable environmental protection regulations. The regulations of the trade associations or other supervisory authorities that are in force locally must always be observed. 5. The manufacturer cannot be held responsible for any losses or damage resulting from unauthorised modifications to the swing/slide. IMPORTANT SAFETY NOTE The metal body of the fitting must not be opened under any circumstances, as the internal components are spring loaded and under a lot of tension and there is a risk of injury. If you pay attention to the above advice, you will be able to enjoy the swing/slide fitting for a long time. In case of further questions or doubts, please do not hesitate to get in contact with us. huwilift-swing/slide 3

4 1 General dimensional indications, swing. Cabinet height mm (R, S) A = Position of interior shelves A 4 huwilift-swing/slide

5 2 General dimensional indications, slide. Cabinet height mm (H) huwilift-swing/slide 5

6 3 General dimensional indications, slide. Cabinet height mm (K) huwilift-swing/slide

7 4 General dimensional indications, slide. Cabinet height mm (L) huwilift-swing/slide 7

8 5 General dimensional indications, slide. Cabinet height mm (M) huwilift-swing/slide

9 6 Drill holes for the swing/slide body in accordance with the drilling diagram. For all cabinet heights 21.5 A Drilled holes A =Ø 5 mm x min. 12 deep B = customer-specific depending on the screws selected (4 x 35 screws recommended) 15 B Ø5 Ø5 A = Drilling depth huwilift-swing/slide 9

10 7 Drill holes for the swing-door in accordance with the drilling diagram. Cabinet height mm (R, S) B* Design for particle board and MDF board ,5 A* B* B* 18 Bohrbild Drilling Deckelrückseite diagram for reverse side of door. 18 Bohrbild Deckelrückseite Bohrbild Deckelrückseite 215,5 Bohrbild Deckelrückseite C A* and B* = observe overlay! C = Drilling depth Ø5 Ø5 A* 10 huwilift-swing/slide

11 8 Drill holes for the swing-door in accordance with the drilling diagram. Cabinet height mm (R, S) Design for 20 mm aluminium frame profile A* 215,5 Bohrbild Drilling Deckelrückseite diagram for reverse side of door. Bohrbild Deckelrückseite Bohrbild Deckelrückseite 215,5 Bohrbild Deckelrückseite 7 A* = observe overlay! A* huwilift-swing/slide 11

12 9 Drill holes for the slide-door in accordance with the drilling diagram. Cabinet height mm (H, K, L, M) B* Design for particle board and MDF board. A* Y X A* B* B* 18 Bohrbild Drilling Deckelrückseite diagram for 18 reverse side of door. Bohrbild Deckelrückseite Bohrbild Deckelrückseite Bohrbild Deckelrückseite Y C A* and B* = observe overlay! X Y C = Drilling depth H mm mm K L mm mm mm mm Ø5 Ø5 M mm mm 12 huwilift-swing/slide

13 10 Drill holes for the slide-door in accordance with the drilling diagram. Cabinet height mm (H, K, L, M) Design for 20 mm aluminium frame profile. X Y A* Bohrbild Drilling Deckelrückseite diagram for reverse side of door. Bohrbild Deckelrückseite Y Bohrbild Deckelrückseite Bohrbild Deckelrückseite 7 A* = observe overlay! X Y A* H mm mm K mm mm L mm mm M mm mm huwilift-swing/slide 13

14 11 Screw on fixation brackets swing/slide. Design for aluminium frame. Design for particle board and MDF board. Euro-Schrauben Euro-screws Ø Ø 5 5 mm mm 14 huwilift-swing/slide

15 12 Screw on swing/slide body. Caution! Do not remove safety bolt! Otherwise risk of injury. Safety Sicherungsbolzen bolt Safety pin Sicherungsbolzen Sicherungsbolzen 3 Spax-Schrauben, Länge min. 35 mm 3 Spax-Schrauben, Länge 3 wood min. screws, 35 mm 3 min. Spax-Schrauben, length 35 mm Länge min. 35 mm 3 Spax-Schrauben, Länge min. 35 mm 33 Euro-Schrauben Euro-screws Ø Ø 5 5 mm mm 3 Euro-Schrauben Ø 5 mm 3 Euro-Schrauben Ø 5 mm 3 Euro-Schrauben Ø 5 mm huwilift-swing/slide 15

16 13 Install regulation part, swing/slide. Connect regulation part 1 with guide pin 2 of swing/slide arm and secure with fixation clip huwilift-swing/slide

17 14 Pre-install transversal stabilization bar, swing/slide. Loosen up clamp screw 3. Connect transversal stabilization bar 1 with traction lever Fit the bar with the lever into the cabinet, leaving minimal free play. SW 3 3 Tighten clamp screw 3. Click Press in axis piece 4 into traction lever with transversal stabilization bar and engage with receptive base plate huwilift-swing/slide 17

18 15 Connect traction lever, swing/slide. swing Connect traction lever 1 with regulation part 2 and secure with fixation clip slide Connect traction lever 1 with regulation part 2 and secure with fixation clip huwilift-swing/slide

19 16 Attach cabinet door, swing/slide. Hang in cabinet door 1 and secure with hexagonal screw 2 (size SW 3), leaving still some free play for the door. Sketch shows slide. Attachment of Abb. zeigt slid swing-door Abb. identical. zeigt slid Abb. zeigt slid Abb. zeigt slid 1 2 Slightly lift up cabinet door and pull out safety bolt 3. Caution! Door will stay put in any position only after adequately adjusting the spring tension. 3 huwilift-swing/slide 19

20 17 Fine-adjust according to door-weight, swing/slide. Clip on cover cap 1. 1 Fine-adjust the fittings on both sides of the cabinet evenly according to the door weight. Adjust positioning screw 1 as required by using an SW 10 size allen key and turning it in a clockwise direction, max. till end position, until the cabinet flap is held in any position. Press on cover plug 2. 1 SW huwilift-swing/slide

21 18 Fine-adjust according to door height, swing/slide. Adjust positioning screw 2 by means of an Allen key 1 (size SW 3) in such a way as to ensure that the door is in a perfectly level position and that the distance X is even. X 2 1 huwilift-swing/slide 21

22 19 Fine-adjust according to door inclination, swing/slide. Adjust positioning screw 2 and 3 by means of an Allen key 1 (size SW 3) in such a way as to ensure that the door rests in an optimum manner on the carcass frame. Pull on tightly screw huwilift-swing/slide

23 20 Fine-adjust according to door alignment, swing/slide. Adjust left and right regulation bush 1 by means of a spanner 2 (size SW 13) in such a way as to ensure that the door rests in a perfect mid-position Y Y huwilift-swing/slide 23

24 21 Carry out functional test, swing/slide. swing If everything has been adjusted correctly, the door will stay put in any position (starting from an opening angle of approximately 30 ). slide If everything has been adjusted correctly, the door will stay put in any position (starting from an opening angle of approximately 30 ). 24 huwilift-swing/slide

25 22 Selecting your huwilift-swing The right version results from height and weight of the cabinet door, as shown in the table. According to the width of your cabinet, you choose the fitting cross bar. Example: A door of 500 mm height and 900 mm width has for instance a total weight of 7.0 kg. As a result, you need Set R 30 with Item No The matching cross bar is No Set huwilift-swing (without cross bar) Cabinet height Short description / Item No. / Door weight R 10 R 20 R 30 R 40 R mm kg kg kg kg kg to 600 mm kg kg kg kg kg to 660 mm kg kg kg kg kg S 10 S 20 S 30 S to 720 mm kg kg kg kg to 800 mm kg kg kg kg Packing unit: 5 sets Cross bar for huwilift-swing Cabinet width Item No. 600 mm , mm , mm ,00 Special dimensions on request huwilift-swing/slide 25

26 23 Selecting your huwilift-slide The right version results from height and weight of the cabinet door, as shown in the table. According to the width of your cabinet, you choose the fitting cross bar. Example: A door of 450 mm height and 900 mm width has for instance a total weight of 6.5 kg. As a result, you need Set K 20 with Item No The matching cross bar is No Set huwilift-slide (without cross bar) Cabinet height Short description / Item No. / Door weight mm H 10 H 20 H 30 H 40 H ,6 4,6 kg 4,7 5,7 kg 5,8 7,0 kg 7,1 9,1 kg 9,2 11,8 kg mm K 10 K 20 K 30 K 40 K ,8 6,0 kg 6,1 7,6 kg 7,7 9,8 kg 9,9 11,4 kg 11,5 14,6 kg mm L 10 L 20 L 30 L ,7 5,9 kg 6,0 7,6 kg 7,7 9,2 kg 9,3 11,6 kg mm M 10 M 20 M ,3 6,6 kg 6,7 7,9 kg 8,0 10,3 kg Packing unit: 5 sets Cross bar for huwilift-slide Cabinet width Item No. 600 mm , mm , mm ,00 Special dimensions on request 26 huwilift-swing/slide

27 huwilift-swing/slide 27

28 HUWIL-WERKE GmbH Möbelschloß- und Beschlagfabriken Brölstraße 2 D Ruppichteroth Phone: Fax: verkauf-inland@huwil.de export-international@huwil.de internet: