I:RRFTSMRN. owner's manual FOR YOUR SAFETY COMMERCIAL DUTY VAC CART. Model No ' Fits Most 16 Gallon Craftsman Wet Dry Vacs

Size: px

Start display at page:

Download "I:RRFTSMRN. owner's manual FOR YOUR SAFETY COMMERCIAL DUTY VAC CART. Model No ' Fits Most 16 Gallon Craftsman Wet Dry Vacs"

Suzanna Watts
5 years ago
Views:

1 r Save This Manual for Future Reference SEARS owner's manual Model No ' Serial Number Model and serial number may be found on the back of the bracket-handle. You should record both model and serial numberina sere placefor future use. I:RRFTSMRN COMMERCIAL DUTY VAC CART FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY Fits Most 16 Gallon Craftsman Wet Dry Vacs assembly operating repair parts _,. Seam, Roebuck and Co., Hoffman Estates, IL U.S.A. Part No. SP5389 Form No. SP Printedin U.S,A.

2 Introduction This cart is designed especiallyfor use with Craftsman 16 gallonwetjdryvacs only. For best results, be sureto followthese instructions. Table of Contents Section Page Introduction... 2 Table of Contents... 2 Unpackingand Checking Contents... 2 Listof Loose Parts... 2 Assembly... 3 Unpacking and Checking Contents List of Loose Parts Key DncrlpUon Qty. P PlasticHandle Bracket... 1 Q Left Leg... 1 R RightLeg... :... 1 S Tote... 1 T Metal Handle... 1 U 3" Caster... 2 Section Page Tool Required... 3 Maintenance... 6 Castersand Wheels... 6 Frame and Handles... 6 Repair Parts... 8 Key Description Qty. V 10"Wheel... 2 W Caster Feet...,... 2 X Cradle, Right... 1 Y Cradle, Left... 1 Z Axle... 1 A B D E u G Bag Of Loose Parts - Containing the following: L Ring, Retaining 1/ M Screw,Type AB#10 x 3/ "(]===, 2

3 Phillips Screwdriver Pliers If any parts are missingor damaged, stop and contact your Authorized Service Center, Do not assemble until you have all the parts. 1. Turnthe drum upside down on the floorwiththe drain facing you. 2. Insert (2) caster feet into the bottom of drum as shown. Lighttaps with a hammer may be needed to fully seat the caster feet. Front Caster 3. Locate the rightand left hand legs. Separate the legs from the molded connection.locate the right and left cradles. Separate the cradles from the moldedconnections. Cradle._ Right _" Stem S Cradle Left 4. Insert right and left legs into right and left cradles. (Slot on legshould line up with hole on cradle) 5. Rotate drum so that drain faces away from you. 6. Hold right leg in right hand and right cradle in left hand. 7. Line up right cradle stem with hole in drum. insert stem into hole in drum and positionlip on leg behind lip on drum. Lighttaps with a hammer maybe needed to fully seat the right cradle. 8. Repeat step 6 for left cradle and leftleg. on Drum

4 Assembly (continued) 9. Mount (1) retaining ring onto one end of axle. Using pliers,snap retainingring intogrooveon axle. 10. Slide wheel onto open end of axle. 11. Slide open end of axle thru cradle left and left leg, making sure the leg slot lines up withthe cradle hole. Slide allthe way through the cradle rightand rightleg. Light taps with a hammer may be required to fully insert axle. Cradle Righ_ II Open End Left Leg..j_i Cradle Left Axle w/wheel 12. Slide wheel onto open end of the axle and mount second retainingring. Retaining Ung Wheel 13. Insert the caster stem into the socket of the caster foot as shown. (Front casters only) 14. Push on the caster untilthe ball on the caster stem is insertedallthe way intothe socket. Youwillbe ableto hear the ball snap into the socket and the caster will swiveleasilywhen positioningiscorrect. 15. Flipdrum uprightso as to rest on two casters and two 10" wheels. Socket 4

5 16.Slide plastichandle bracket onto right and left legs. 17. Slide metal handle into (2) holes on plastic handle bracket. 18. Align holes in handlewith hole in legand plastichandle bracket. Metal Handle Plastic Handle Bracket f m h Install (2) #10 x 314 screws into (2) holes on legs with (2) matching holes on handle for each side. NOTE: To adjust height, slide metal handle up till one hole is visible on each side. The (2) holes on legs should then line up with (2) holes on metal handle. WARNING: To reduce the risk of personal Injury or damage to unit from handle failure, make sure the SCIONSare fully screwed in and snug, but not so tight they crack the p astic. 5

6 Assembly (continued) 20. Locate(2) tabs on plastic handlebracketand position (2) slots on tote, Slide tote down over (2) tabs on bracket. Tabs Handle Bracket ToteJ Slots WARNING: To reduce the risk of injury: Before Each Use Check for missing, damaged or broken pads. Repair any damage and replace any missing parts before using cart. During Use To reduce the risk of being struck by or pulled down by a rolling vac: Block the casters on any uneven or sloped surface before starting to vacuum. Use extra care on uneven surfaces that let the cart tip or rock. Maintenance Casters and Wheels Should your cart become hard to roll or squeak, you shouldplace two or three drops of general purposeoil on each wheel at the axle. WARNING: To reduce the risk of back injury, falls or impact from falling vac: Limit the weight in the drum before lifting the vac or moving it up or down stairs. For liquids, drain the vac drum. For heavy, dry media, empty the vac drum. Get help when you need to life the vac to empty It, or tip the drum over on it's side and pour the media into a disposal container. Frame and Handles Your metal handle is plated to prevent rust, however, liquids and corrosivedebris should be wiped off witha soft clothshouldthey come in contactwith the handle.

7 Repair Parts Parts List for Vac Cart Model No \ I 10 i j 6 4\ Alwaysorder by Part Number- Not by Key Number Kay No Part No. Description Key No Pa_ No. Descrtption Handle Bracket, Handle Left Leg STD Ring, Retaining 112" " Wheel Axle Cradle, Left Caster Foot SP5389 Caster Cradle, Right Right Leg,_LScrew TY AB #10 x 3/4 Tote Bag of Loose Parts (NotIllustrated) Owners Manual (Not Illustrated) * Standard hardware item - may be purchased locally, I_,WARNING: These parts are important to the safety of this product. Do not substitute with common parts. I 7

8 #.- _ #r )1, SEARS owner's manual COMMERCIAL VAC CART DUTY Model No , Fortke repairorreplecementparisyouneed (;all7 am - 7 pm,7 daysaweek PAITT ( ) The model number of yourcommercial Duty Vac Cart will be found on the back of the handle bracket. Forin-homemajorbrandrepairservice Call24 hoursa day,7 daysa week REPAIR ( ) Forthe locationof a SearsRepairServiceCenterin yourarea Call24 hoursa day,7 daysa week When requesting service or ordering parts, always provide the following information: ProductType Model Number Part Number Part Description Forinfornmtlonon purchasinga Sears MaintenanceAgreementor to inquire aboutan existingagreement Call 9 am - 5 pro,monday-saturday SEARS _ t998 Emerosn Electric Co. Seam, Roebuck and Co., Hoffman Estates, IL U.S.A. Part No. SP5389 Form No. SP Printed in U.S.A. 12/98

USER S MANUAL CAUTION. Visit our website at. new products, prizes, fitness tips, and much more! Model No Serial No.

USER S MANUAL CAUTION. Visit our website at. new products, prizes, fitness tips, and much more! Model No Serial No. Model No. 831.19832 Serial No. The serial number is found in the location shown below. Write the serial number in the space above. USER S MANUAL Serial Number Decal SEARS, ROEBUCK AND CO. HOFFMAN ESTATES,