MAINTENANCE MANUAL DI 16

Size: px
Start display at page:

Download "MAINTENANCE MANUAL DI 16"

Transcription

1 MAINTENANCE MANUAL DI % Press Ctrl + L for full screen 1

2 STANDARD INSTALLATION Inlet Outlet Optional accessories: Pressure regulator Solenoid valves Water meter Flow restrictor 200 Mesh/ 80 micron filter Concentrate Optional accessories Union ball check/ check valve or water hammer arrestor 2

3 MAIN MENU CHAPTER 1 Removing the dispenser from the installation CHAPTER 2 Disassembling the dispenser CHAPTER 3 Reassembling the dispenser CHAPTER 4 Maintenance of PX piston CHAPTER 5 Maintenance of air bleed CHAPTER 6 Troubleshooting guide «click» on the desired Chapter or «click» for next slide 3

4 SPECIFICATIONS Injection Range: 1:500 (0.2%) to 1:64 (1.6%) Water Flow Range: 0.05 to 11 GPM Operating Water Pressure: 4.3 to 85 PSI Maximum Water Temperature: 104 F 40 C Note: Normal safety precautions should be practiced when working with chemicals and equipment. 4

5 CHAPTER 1 REMOVING THE DISPENSER FROM INSTALLATION «Click» to go back to the main menu «Click» for next slide 5

6 DISASSEMBLING OF THE DISPENSER FROM THE INSTALLATION After turning off the water and relieving the pressure on the unit, unscrew the dispenser inlet/outlet couplings and allow it to drain. Unscrew the suction tube nut and remove the hose. 6

7 CHAPTER 2 DISASSEMBLING THE DISPENSER «Click» to go back to the main menu «Click» for next slide 7

8 DISASSEMBLING THE DISPENSER Unscrew middle retaining nut. 8

9 DISASSEMBLING THE DISPENSER Pull the injection stem assembly out of the injection sleeve, and let the solution drain out of it. Caution: Stem may be full of undiluted chemical. Be aware of hazardous materials and take the necessary precautions for protection. WATCH OUT FOR SPLASHING! 9

10 DISASSEMBLING THE DISPENSER With the injection stem assembly in your hands, unscrew the check valve nut. 10

11 DISASSEMBLING THE DISPENSER Gently push the check valve out of the dosing stem with a pencil or similar object. Do not scratch the inside of the dosing stem. 11

12 DISASSEMBLING THE DISPENSER Separate the check valve assembly. Remove the check valve retainer with the help of small flat head screw driver. Then, remove the cone and the spring. 12

13 DISASSEMBLING THE Y OF DISPENSER Unscrew the bell housing and remove it. 13

14 DISASSEMBLING THE DISPENSER Unscrew the plunger by pushing the piston down as far as possible. Use the narrow end of the suction tube nut as a tool to unscrew the plunger. 14

15 DISASSEMBLING THE DISPENSER Remove the piston assembly. 15

16 DISASSEMBLING THE DISPENSER Unscrew the injection sleeve from the body of the dispenser. Check that the O-ring, retainer and seal are on the injection sleeve. If not, remove them from the inside of the dispenser. 16

17 DISASSEMBLING THE DISPENSER Remove the screen from the body, put the dispenser body on a table, hold it firmly and at the same time lift the screen with your fingers. Remove the bell housing seal. 17

18 DISASSEMBLING THE DISPENSER Disassembly of the diffuser assembly is only necessary if a leak develops. Unscrew the diffuser nut. Push the diffuser towards the interior of the dispenser. Bump it with your palm if necessary. Remove the diffuser assembly. 18

19 DISASSEMBLING THE DISPENSER CLEANING & MAINTENANCE PROCEDURE When the disassembly of the Dosatron unit is complete, soak it in lukewarm soapy water. A soft bristled brush may be used to break residue. Change seal kit every 12 months. Seal kit part No. EDDI002 includes: JDI012 - Top O-ring JDI011 - Top seal JDI010 - Plunger seal JDI009 - Injection stem O-ring MDI028 - Check valve spring PDI032 - Check valve cone JDI011 - Check valve seal JDI012 - Check valve O-ring 19

20 CHAPTER 3 REASSEMBLING THE DISPENSER «Click» to go back to the main menu «Click» for next slide 20

21 REASSEMBLING THE DISPENSER Place the screen inside the body. Then, reseat or replace the bell housing O-ring. Replace the O-ring if leaking. 21

22 REASSEMBLING THE DISPENSER If the diffuser is leaking, replace the diffuser O-ring. Install the diffuser assembly into the body. Be sure to align the notch in the diffuser with the tooth that is molded in the body. Install the diffuser nut hand tight. 22

23 Injection Assembly REASSEMBLING THE DISPENSER Replace the check valve O-ring. Replace the check valve seal on the barb fitting with the raised portion facing upward. 23

24 Injection Assembly REASSEMBLING THE DISPENSER Replace the check valve cone and spring. Insert them in the check valve guide. Then, put the check valve retainer to hold the cone and the spring in place. Caution: Small, spring loaded parts are easily lost! 24

25 Injection Assembly REASSEMBLING THE DISPENSER Assemble the check valve assembly by firmly pushing the guide and the barbed fitting together. 25

26 Injection Assembly REASSEMBLING THE DISPENSER Replace the injection stem O-ring. 26

27 Injection Assembly REASSEMBLING THE DISPENSER Insert the check valve assembly into the injection stem. Slide the middle nut on the stem and thread the check valve nut. 27

28 Injection Sleeve Assembly REASSEMBLING THE DISPENSER Replace the injection seal on the injection sleeve. Make sure the raised part is facing up. Put the top seal retainer with the ridge toward the seal. 28

29 Injection Sleeve Assembly REASSEMBLING THE DISPENSER Replace the sleeve O-ring on the top of the retainer. Thread the injection sleeve assembly into the body of the dispenser. 29

30 Plunger Assembly REASSEMBLING THE DISPENSER Replace the plunger seal. Make sure not to damage the seal or plunger. 30

31 Plunger Assembly REASSEMBLING THE DISPENSER Push the piston down as far as possible and screw the plunger onto the plunger rod. Use the narrow end of the suction tube nut as a tool to screw the plunger all the way until it stops. 31

32 REASSEMBLING THE DISPENSER Insert the piston assembly. 32

33 REASSEMBLING THE DISPENSER Screw the bell housing onto the body of the dispenser. It should be hand tight. 33

34 REASSEMBLING THE DISPENSER Insert the injection stem assembly into the sleeve. Insert the stem ring into the sleeve assembly until flush. Align tooth on sleeve with a notch in clear adjusting nut. 34

35 REASSEMBLING THE DISPENSER Thread the middle nut onto the injection sleeve. 35

36 REASSEMBLING THE DISPENSER The dispenser is ready to be reinstalled. 36

37 CHAPTER 4 MAINTENANCE OF PX PISTON «Click» to go back to the main menu 37

38 MAINTENANCE OF PX PISTON Piston Fit Test Insert upper portion of piston into the bell housing half way down, turn the bell housing upside down and hold the smaller part of the piston ONLY, then lift it. The piston should be snug in the bell housing and the bell housing should not fall off, if it does the upper piston shell needs to be replaced. Also inspect the inside of the bell housing and look for deep vertical scratches. If this is the case, the bell housing needs to be replaced. 38

39 Piston Fit Test MAINTENANCE OF PX PISTON Note: It is best to remove the plunger (page 14) prior to doing this test so it will not interfere. Insert the lower part of the piston half way down the body. Holding onto the top of the piston, let go of the body. The piston should be snug in the body, and the body should not fall off, if it does the lower piston shell needs to be replaced. Also inspect the inside of the body and look for deep vertical scratches. If this is the case, the body needs to be replaced. 39

40 Disassembly of piston MAINTENANCE OF PX PISTON Remove the plunger rod. To do so, turn the nut 1/8 turn counter clockwise. Pull on nut once, then, turn again the nut 1/8 turn counter clockwise. 40

41 Disassembly of piston MAINTENANCE OF PX PISTON Remove the upper valves by squeezing the upper area of the valve. 41

42 Disassembly of piston MAINTENANCE OF PX PISTON Unscrew the 4 screws that connect the piston rod retainer to piston shell. Remove the piston rod retainer. Pull out the actuator assembly from the top. 42

43 Disassembly of piston MAINTENANCE OF PX PISTON Remove screws from outer perimeter of piston shell. Separate the upper piston shell from the lower piston shell. Remove the seal between the two piston shells. 43

44 Reassembly of piston MAINTENANCE OF PX PISTON Replace the seal between the two piston shells. Put together the upper and the lower piston shells. Screw the screws from outer perimeter of piston shell. 44

45 Reassembly of piston MAINTENANCE OF PX PISTON Replace the lower valves O-rings if they are missing or deteriorating. Replace the toggle spring. Insert the piston assembly into the piston shell. Make sure that the two guides are aligned with the piston shell columns. 45

46 Reassembly of piston MAINTENANCE OF PX PISTON Put together the piston rod retainer, the two feet should face downward. Install the piston rod retainer in the piston shell. Attach it with the four screws. 46

47 Reassembly of piston MAINTENANCE OF PX PISTON Replace the O-rings on the upper piston valves if they are missing or deteriorating. Insert the two upper piston valves. The splits in the valves should line up. 47

48 Reassembly of piston MAINTENANCE OF PX PISTON Install plunger rod in the rod retainer. The pin in the head of the rod should be aligned with the slot inside the rod retainer. Lock it in to place by turning the lock nut clockwise 1/8 turn, pushing it down and 1/8 turn clockwise again. 48

49 MAINTENANCE OF PX PISTON Reset Piston To reset the piston, remove the bell housing, push the piston all the way down, it may click, pull the piston all the way up. Holding it in up position, push down on the vertical posts and it should click. Push the piston back down and screw the bell housing on. 49

50 CHAPTER 5 MAINTENANCE OF AIR BLEED «Click» to go back to the main menu «Click» for next slide 50

51 Disassembly of air bleed MAINTENANCE OF AIR BLEED Remove the rubber cap from the top of the air bleed button. 51

52 Disassembly of air bleed MAINTENANCE OF AIR BLEED Using a small flat blade screwdriver, gently pry loose the ribbed collar. Remove the ribbed collar by pulling it straight up. 52

53 Disassembly of air bleed MAINTENANCE OF AIR BLEED Gently twist the air bleed button with pliers (if necessary) until the two tabs on the air bleed button align with the corresponding grooves in the bell housing. Remove the air bleed button by pushing it through the bell housing. 53

54 Reassembly of air bleed MAINTENANCE OF AIR BLEED Replaced the O-ring. The only serviceable part on the air bleed is the O-ring. 54

55 Reassembly of air bleed MAINTENANCE OF AIR BLEED Align the two tabs on the air bleed with the corresponding grooves in the bell housing. 55

56 Reassembly of air bleed MAINTENANCE OF AIR BLEED Install the air bleed button from the inside of the bell housing. Make sure the two tabs get out of the bell housing. Rotate the air bleed button a quarter turn. 56

57 Reassembly of air bleed MAINTENANCE OF AIR BLEED Install the ribbed collar so that the tabs fit into the slots in the collar. Re-install the rubber cap on the air bleed button. 57

58 CHAPTER 6 TROUBLESHOOTING GUIDE «Click» to go back to the main menu «Click» for next slide 58

59 TROUBLESHOOTING SYMPTOM PISTON Piston is not clicking Excessive water flow Water hammer CAUSE The unit is installed in the wrong direction Piston locked up/not clicking or bypass is in OFF position. Presence of air inside the bell housing In-line water filter or inside screen is clogged Worn piston shells, bell housing or body Scratched/scored piston shells, bell housing and/or body REMEDY The arrow on the unit should point in the same direction as the water flow. Water supply and demand valve should be open. Reset piston. See page 49 for instructions. Flip bypass to ON position if dispenser is equipped with manual bypass Bleed out the air by pushing the air bleed button until constant flow of water comes out from around the button. 1. Reduce the flow rate and restart the unit slowly. 2. Open bell housing, check O-rings around the four piston valves (2 at the top, 2 at the bottom) to see if they are missing or dislodged. 3. Reset the piston (see page 49 for instructions) screw bell housing back on. Reset piston (see page 49 for instructions) and install water hammer arrestor in the appropriate location. Clean the in line water filter. Clean the inside screen (see pages 17 and 21). Do piston fit test (pages 38-39). Replace piston shells, body and bell housing as necessary. Make sure your installation has a 200 mesh filter before the Dosatron. Do piston fit test (pages 38-39). replace piston shells, body and bell housing as necessary. Make sure your installation has a 200 mesh filter before the Dosatron. 59 COPYRIGHT, DOSATRON INTERNATIONAL S.A., 2002

60 TROUBLESHOOTING SYMPTOM DOSING Water flowing back into solution container. No suction of solution CAUSE Check valve dirty, worn, assembled incorrectly or missing Piston locked up/not clicking or bypass is in OFF position Air leak in the suction tube Suction tube or strainer clogged Check valve worn, improperly assembled, dirty or damaged Plunger seal is damaged, swollen or missing Worn piston shells, bell housing or body REMEDY Clean or replace check valve parts and reassemble check valve correctly. Be sure the check valve seal is in proper position. Pages Reset piston. See page 49 for instructions. Flip bypass to ON position if dispenser is equipped with manual bypass Check suction tube connection. Inspect suction tube for pin holes or cracks. Check tightness of connection nuts. Cut ½ of top of the hose and reattach it correctly. Clean suction tube and strainer or replace hose assembly. Raise strainer 2 off the bottom of stock tank solution. Clean or replace check valve parts. In particular the seal and the cone. Pages Clean or replace plunger seal. If plunger seal is missing, check incoming water pressure; refer to unit manual for specifications. Do piston fit test (pages 38-39). If necessary replace piston shells, body and bell housing. Make sure your installation has a 200 mesh filter before the Dosatron. 60 COPYRIGHT, DOSATRON INTERNATIONAL S.A., 2002

61 TROUBLESHOOTING SYMPTOM Under-Injection Worn or scratched piston shells, bell housing and/or body Suction of air CAUSE Excessive water flow Worn plunger seal Worn or cracked injection stem Check valve worn, improperly assembled, dirty or damaged Do piston fit test (pages 38-39). If necessary replace piston shells, bell housing and/or body. Make sure your installation has a 200 mesh filter before the Dosatron. Check suction tube connection. Inspect suction tube for pin holes or cracks. Check tightness of connection nuts. Cut ½ off top of the hose and reattach it correctly. Listen to the unit clicking, count the individual clicks, should not exceed 36 clicks in 15 seconds otherwise is excessive flow. If excessive flow reduce the flow rate and restart the unit slowly. Replace plunger seal. Replace injection stem. REMEDY Clean or replace check valve parts. In particular the seal and the cone. Pages COPYRIGHT, DOSATRON INTERNATIONAL S.A., 2002

62 TROUBLESHOOTING SYMPTOM LEAKS Leaks in the vicinity of the black nut under the body Leaks between the body and the bell housing CAUSE Diffuser seal is damaged or positioned incorrectly Diffuser is installed incorrectly Body may be cracked Bell housing seal is damaged, positioned incorrectly or missing REMEDY Position correctly or replace the diffuser seal. Check tightness of the nut. Pages 18 & 22. Position correctly or replace the diffuser if damaged. Align notch in the diffuser with tooth molded in the body. Pages 18 & 22. Check and replaced the body if necessary. Position correctly, clean the seal seat, or replace the bell housing seal. 62 COPYRIGHT, DOSATRON INTERNATIONAL S.A., 2002

63 Thank you for using Dosatron liquid dispensers. Please contact us at (800) for further assistance or visit our website at Sunnydale Blvd., Clearwater, Florida

REBUILD KIT. Extend the Life of Your Dosatron. D14MZ2VFIIK Part #: MKD14MZ2K Kit includes:

REBUILD KIT. Extend the Life of Your Dosatron. D14MZ2VFIIK Part #: MKD14MZ2K Kit includes: Extend the Life of Your Dosatron REBUILD KIT 800-523-8499 727-443-5404 D14MZ2VFIIK Part #: MKD14MZ2K Kit includes: Part 1: Piston Kit Upper flange Lower flange Omega spring Connecting rod Push rod seal

More information

DI GPM Operating Manual

DI GPM Operating Manual DI 16 11 GPM Operating Manual CONTENTS INTRODUCTION... 1 Specifications... 1 Accessories... 2 Operating Principle... 3 BOX CONTENTS... 4 PRECAUTION... 5 Installation... 5 Maintenance... 5 Service... 5

More information

0.7 m 3 /h - 3 GPM D 07 RE 125 D 07 RE 5. owner s manual

0.7 m 3 /h - 3 GPM D 07 RE 125 D 07 RE 5. owner s manual 0.7 m 3 /h - 3 GPM D 07 RE 125 D 07 RE 5 owner s manual GB You have just become the owner of one of the latest in the line of DOSATRON proportional dosing pumps and we congratulate you on your choice.

More information

D25RE2 D25RE2 Maintenance

D25RE2 D25RE2 Maintenance Scan the QR code to watch our D25RE2 - Service video. 800-523-8499 D25RE2 D25RE2 Maintenance Service Service Kit Includes: Before we start make sure the injector is clicking. If not, be sure to watch the

More information

Agxcel GX12i Chemical Injection System

Agxcel GX12i Chemical Injection System Agxcel GX12i Chemical Injection System Table of Contents System Contents... 3 Specifications... 4 Safety Precautions and Tips... 5 Operations... 6 Installation... 7 Maintenance... 8-9 Troubleshooting...

More information

Service Manual Air Plus Second Stage

Service Manual Air Plus Second Stage Service Manual Air Plus Second Stage Includes XS Series Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Plus Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS

More information

Service Manual Air Tech Second Stage

Service Manual Air Tech Second Stage Service Manual Air Tech Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Tech Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION... 9

More information

owner s manual 11 US GPM RANGE The diaphragm Dosatron CUSTOMER SERVICE - SERVICE CLIENTÈLE MANUFACTURED BY - FABRIqUé PAR DM 11 F DM 11 RE 3

owner s manual 11 US GPM RANGE The diaphragm Dosatron CUSTOMER SERVICE - SERVICE CLIENTÈLE MANUFACTURED BY - FABRIqUé PAR DM 11 F DM 11 RE 3 The diaphragm Dosatron 11 US GPM RANGE DM 11 F DM 11 RE 3 CUSTOMER SERVICE - SERVICE CLIENTÈLE NORTH & CENTRAL AMERICA : DOSATRON INTERNATIONAL INC. 2090 SUNNYDALE BLVD. CLEARWATER - FL 33765 - USA Tel.

More information

DP5 Pump. 5:1, Air-operated, Heavy Duty, Oil. General. Operation. Technical Data. Installation R1 09/10

DP5 Pump. 5:1, Air-operated, Heavy Duty, Oil. General. Operation. Technical Data. Installation R1 09/10 DP5 Pump 5:1, Air-operated, Heavy Duty, Oil General The DP5 Pump is a compressed air-operated reciprocating piston medium pressure pump. These pumps are suitable for distribution of all types of light

More information

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,

More information

AGXCEL GX12i CHEMICAL INJECTOR 2% INJECTOR UNIT - PN# % INJECTOR UNIT - PN# E 6TH ST KEARNEY NE

AGXCEL GX12i CHEMICAL INJECTOR 2% INJECTOR UNIT - PN# % INJECTOR UNIT - PN# E 6TH ST KEARNEY NE AGXCEL GX12i CHEMICAL INJECTOR 2% INJECTOR UNIT - PN#20202 5% INJECTOR UNIT - PN#20556 116 E 6TH ST KEARNEY NE 68847 877.218.1981 #1 Table of Contents System Contents... 3 3 Specifications... 4 4 and Tips...

More information

3.1 DISPENSER BLACK SHADOW SERIES. Tools Needed for Mounting SCS Dispenser Hammer

3.1 DISPENSER BLACK SHADOW SERIES. Tools Needed for Mounting SCS Dispenser Hammer SCS 2 BLACK SHADOW SERIES 3.1 DISPENSER ALWAYS OBSERVE PRODUCT SAFETY AND HANDLING INSTRUCTIONS. ALWAYS DIRECT DISCHARGE AWAY FROM YOU or other persons. ALWAYS DISPENSE CLEANERS AND CHEMICALS AS DIRECTED

More information

Maintenance Information

Maintenance Information 16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Firehawk Second Stage Regulator Fire Service

Firehawk Second Stage Regulator Fire Service Firehawk Second Stage Regulator Fire Service MAINTENANCE AND REPAIR TAL 1701 (L) Rev. 2 MSA 2017 Prnt. Spec. 10000005389(I) Mat. 10147454 Doc. 10147454 TAL 1701 (L) Rev. 2-10147454 2 NON-CBRN FIREHAWK

More information

2.5 m 3 /h - 11 GPM. manuel d utilisation owner s manual gebrauchsanweisung manuale d uso manual de utilización gebruiksaanwijzing

2.5 m 3 /h - 11 GPM. manuel d utilisation owner s manual gebrauchsanweisung manuale d uso manual de utilización gebruiksaanwijzing 2.5 m 3 /h - 11 GPM D 25 F D 25 F 1 D 25 F 0.2 D 25 F 2 D 25 RE 1500 D 25 RE 09 D 25 RE 2 D 25 GL 2 D 25 RE 4 D 25 RE 5 D 25 RE 10 D 25 RE 2 IE D 25 RE 5 IE D 25 RE 10 IE D 25 RE 2 IE PO manuel d utilisation

More information

Tools Needed for Mounting Cleá Filling Station

Tools Needed for Mounting Cleá Filling Station ALWAYS OBSERVE PRODUCT SAFETY AND HANDLING INSTRUCTIONS. ALWAYS DIRECT DISCHARGE AWAY FROM YOU or other persons. ALWAYS DISPENSE CLEANERS AND CHEMICALS AS DIRECTED ON THE LABEL. ALWAYS DISPENSE INTO APPROVED

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V 3800V 3900V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V 3800V 3900V Part B, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. 3500V 3700V 3800V 3900V All Piston (F) 4-Port (A) 6-Port (B or C) -Port (S or T) Vista Standard

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3400V 3500V 3700V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3400V 3500V 3700V Part B, Section 1 This section covers the following unit configurations. Model Voltage Pump Manifold Control 3100V 3400V 3500V 3700V All Piston (E) 4-Port (A) 6-Port (B or C) 2-Port (S or T) Vista Standard

More information

METERING VALVE 2" STEM GUIDED

METERING VALVE 2 STEM GUIDED 2" STEM GUIDED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

and 1/4 TURN SECOND STAGE REGULATOR TAL 502 (L) Rev. 0 MSA 2005 Prnt. Spec (I) Mat Doc

and 1/4 TURN SECOND STAGE REGULATOR TAL 502 (L) Rev. 0 MSA 2005 Prnt. Spec (I) Mat Doc and 1/4 TURN SECOND STAGE REGULATOR TAL 502 (L) Rev. 0 MSA 2005 Prnt. Spec. 10000005389 (I) Mat. 10064383 Doc. 10064383 REGULATOR COMPONENTS Item Part No. Description 1 MASK MOUNTED REGULATOR ASSEMBLY

More information

Service Manual. Balanced Piston First Stage

Service Manual. Balanced Piston First Stage Service Manual Balanced Piston First Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Balanced Piston First Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION...

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

Maintenance Information

Maintenance Information Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary

More information

Crispin Valves Operating Guide. Crispin

Crispin Valves Operating Guide. Crispin Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com

More information

DP3 Pump. 3:1, Air-operated, Oil. General. Operation. Technical Data. Installation R0 10/09. 35a 35b 35c

DP3 Pump. 3:1, Air-operated, Oil. General. Operation. Technical Data. Installation R0 10/09. 35a 35b 35c DP3 Pump 3:1, Air-operated, Oil General The DP3 Pump is a compressed air-operated piston reciprocating medium pressure pump. Suitable for medium flow transfer of high viscosity lubricants and for oil delivery

More information

INSTALLATION, OPERATING AND SERVICE MANUAL

INSTALLATION, OPERATING AND SERVICE MANUAL INSTALLATION, OPERATING AND SERVICE MANUAL ECONO-mist WATER SOFTENER Demand Regeneration 7-LMC56-75B 7-LM56-75B 7-LM56-100B 7-LM56-150B 7-LM56-200B Congratulations on purchasing your new Lancaster Water

More information

OWNER S TECHNICAL MANUAL

OWNER S TECHNICAL MANUAL OWNER S TECHNICAL MANUAL Electronic Oil Meter 660 Description Oval gear type Hose end meter with electronic LCD display for Lubricants and Anti-Freeze fluid. The Hose end meter includes a progressive opening

More information

Colt Series C400, C500

Colt Series C400, C500 Colt Series C400, C500 RP/IS-A-C400/C500 C400 OSY Reduced Pressure Zone Assemblies Reduced Pressure Detector Assemblies Sizes: 2 1 2" 10" (65 250mm) Installation Service Repair Kits Maintenance For other

More information

Rancher Hydraulic Chute Owner s Manual.

Rancher Hydraulic Chute Owner s Manual. Rancher Hydraulic Chute Owner s Manual www.powderriver.com Since 1938, we at Powder River have dedicated ourselves to making America s best livestock handling equipment. You have purchased just one of

More information

AIRGO MISTING SYSTEM MAINTENANCE

AIRGO MISTING SYSTEM MAINTENANCE AIRGO MISTING SYSTEM MAINTENANCE WARNING: Disconnect the fan and misting pump from power before servicing. Service schedule Schedule Procedure 50 hours of operation Initial oil change 300 hours of operation,500

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

INSTALLATION INSTRUCTIONS REPAIR SEAL KIT PowerSurvivor 40E

INSTALLATION INSTRUCTIONS REPAIR SEAL KIT PowerSurvivor 40E INSTALLATION INSTRUCTIONS REPAIR SEAL KIT PowerSurvivor 40E PURPOSE OF THE KIT The Repair Seal Kit should be installed after 1000 hours of operation. It should be installed regardless of whether or not

More information

EBF-750 Deck-Mounted Battery Powered Sensor Operated Gooseneck Faucets

EBF-750 Deck-Mounted Battery Powered Sensor Operated Gooseneck Faucets INSTALLATION INSTRUCTIONS BATTERY POWERED SENSOR OPERATED HAND WASHING FAUCETS EBF-750 I.I. Code No. 0816324 EBF-750 Deck-Mounted Battery Powered Sensor Operated Gooseneck Faucets Includes Instructions

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including

More information

M-1115S Series Fuel Pump

M-1115S Series Fuel Pump SAVE THESE INSTRUCTIONS M-1115S Series Fuel Pump Owner s Manual TABLE OF CONTENTS General Information...2 Safety Instructions...2 Installation...3 Operation...4 Maintenance...5 Repair...5 Troubleshooting...9

More information

Maintenance Information

Maintenance Information 16573321 Edition 3 February 2014 Air Grinder Series 61H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM)

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) IOM-1088 03-16 Model 1088 Vacu-Gard Blanketing Valve ISO Registered Company SECTION I I. DESCRIPTION AND SCOPE The Model 1088 Vacu-Gard is a tank blanketing

More information

EXTENDA-BAN VALVE REPAIR AND MAINTENANCE

EXTENDA-BAN VALVE REPAIR AND MAINTENANCE 7 EXTENDA-BAN VALVE REPAIR AND MAINTENANCE 1 1. Detach the Valve and Extension from the hose. Carefully remove the mesh strainer. Squeeze the Trigger to drain all liquid from the Valve. 2 3 4 5 6 2. Remove

More information

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP PAGE 1 OF 10 OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP EFFICIENT, EASY OPERATION Air operated pump Wide range of pressures and volumes Easy to operate controls Output pressure

More information

1/2" AIR DRIVEN DIAPHRAGM PUMP

1/2 AIR DRIVEN DIAPHRAGM PUMP 1/2" DRIVEN DIAPHRAGM PUMP OPERATION AND SERVICE GUIDE O-1225D NOV. 2008 Page 1 of 6 Refer to Bulletin P-605, Parts List P-9151 DRIVEN, DOUBLE DIAPHRAGM PUMP MANUAL Congratulations on purchasing one of

More information

Series 957, 957N, 957Z, 957RPDA, 957NRPDA, 957ZRPDA

Series 957, 957N, 957Z, 957RPDA, 957NRPDA, 957ZRPDA Series 957, 957N, 957Z, 957RPDA, 957NRPDA, 957ZRPDA Reduced Pressure Zone Assemblies Reduced Pressure Detector Assemblies Sizes: 2 1 2" 10" (65 250mm) Installation Service Repair Kits Maintenance RP/IS-957/957RPDA

More information

A REPAIR KIT PART NUMBER IS AVAILABLE AND CONTAINS ALL THE PARTS NORMALLY REPLACED DURING A STANDARD MAINTENANCE REPAIR.

A REPAIR KIT PART NUMBER IS AVAILABLE AND CONTAINS ALL THE PARTS NORMALLY REPLACED DURING A STANDARD MAINTENANCE REPAIR. AZ Pump Instructions PUMP NOT RUNNING PROPERLY: Check to be sure air pressure is reaching the pump, check to be sure air filter is not clogged; clean or replace as required. Check to be sure fluid filter

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

Coro-Vane Maintenance CP471. and Disassembly

Coro-Vane Maintenance CP471. and Disassembly Coro-Vane Maintenance CP471 and Disassembly CoroVane Pumps Pumps all have discharge and suction pressure openings. The following slides depict a 1021, but all standard pumps are repaired the same. Grease

More information

Second Stage Regulator - 1/4 Turn

Second Stage Regulator - 1/4 Turn Second Stage Regulator - 1/4 Turn MAINTENANCE AND REPAIR TAL 806 (L) Rev. 6 MSA 2008 Prnt. Spec. 10000005389 (I) Mat. 10042827 Doc. 10000015245 1/4 TURN SECOND STAGE REGULATOR SECOND STAGE REGULATOR COMPONENTS

More information

Maintenance Information

Maintenance Information 45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.

More information

Maintenance Information

Maintenance Information 16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially

More information

Instructions. Certifications Chrome less spray Chrome with spray 10-K82-WNCH-AD-Z Chrome less spray 10-K82-WYCH-AD-Z Chrome with spray

Instructions. Certifications Chrome less spray Chrome with spray 10-K82-WNCH-AD-Z Chrome less spray 10-K82-WYCH-AD-Z Chrome with spray Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder

More information

MAINTENANCE MANUAL FOR THERMOSTATIC TEMPERATURE REGULATING VALVE TRAC STYLE P

MAINTENANCE MANUAL FOR THERMOSTATIC TEMPERATURE REGULATING VALVE TRAC STYLE P MANUAL NUMBER P-EFS-1 MAINTENANCE MANUAL FOR THERMOSTATIC TEMPERATURE REGULATING VALVE TRAC STYLE P TRAC Regulator Company Inc. 160 South Terrace Avenue Mount Vernon, New York USA 10550-2408 Phone: (914)

More information

Removal and Installation of Fuel Injection Pumps

Removal and Installation of Fuel Injection Pumps Page 16 of 126 worn considerably. Fig. C shows how the flat end of a new plunger makes poor contact with a worn lifter, resulting in rapid wear to both parts. An injection pump can have a good fuel flow

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FUEL PUMP SLEEVE INSTALLATION KIT 2001-2006 BMW E46 M3 Document# 19-0058 Customer Support: info@radiumauto.com 1. There are 2 common ways to relieve fuel pressure on the BMW.

More information

HIGH PRESSURE CONTROL VALVE PISTON BALANCED

HIGH PRESSURE CONTROL VALVE PISTON BALANCED PISTON BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be

More information

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,

More information

INSTALLATION INSTRUCTIONS FOR THE TRUCK MOUNTED VIPER ADDITIVE INJECTION SYSTEM GTP-8776C

INSTALLATION INSTRUCTIONS FOR THE TRUCK MOUNTED VIPER ADDITIVE INJECTION SYSTEM GTP-8776C INSTALLATION INSTRUCTIONS FOR THE TRUCK MOUNTED VIPER ADDITIVE INJECTION SYSTEM GTP-8776C This additive injection system was designed to be used with five gallon jug of additive. The system is supplied

More information

Cylinder and Valve: AirHawk II Air Mask

Cylinder and Valve: AirHawk II Air Mask Cylinder and Valve: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104218 Doc. 10104218 Parts List Cylinder Replacement Kits Item P/N Description

More information

DISCONTINUED. Installation. Aerada 900 Series Futura Faucet. With Accu-Zone (AZ) Infrared Control

DISCONTINUED. Installation. Aerada 900 Series Futura Faucet. With Accu-Zone (AZ) Infrared Control Aerada 900 Series Futura Faucet With Accu-Zone (AZ) Infrared Control BRADLEY SC A S53-141 4" Centerset S53-148 4" Centerset, no Solenoid Valve S53-186 4" Centerset with 8" Trim Plate S53-285 Centershank

More information

LAWN SPRINKLER, IRRIGATION PUMP

LAWN SPRINKLER, IRRIGATION PUMP LAWN SPRINKLER, IRRIGATION PUMP MODEL #, SP0P, SP5P, SP20P, EL0P, EL5P, EL20P SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.

More information

DeZURIK " BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT

DeZURIK  BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT DeZURIK 20 144" BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT Instruction D10373 April 2017 Instructions These instructions provide information about the 20 (250 F2 model only) and the 24-144 BAW

More information

DEMA MIXRITE PROPORTIONING PUMP MODELS 574 & CL & 575CL FOR CORROSIVE LIQUID CHEMICALS INSTALLATION INSTRUCTION.

DEMA MIXRITE PROPORTIONING PUMP MODELS 574 & CL & 575CL FOR CORROSIVE LIQUID CHEMICALS INSTALLATION INSTRUCTION. 10% MixRite Pump I-871 Page 1 MODEL # INDUCTION RANGE%* TECHNICAL DATA TABLE Ability to turn off INDUCTION the chemical flow RANGE RATIO* while water is running OPERATING TEMPERATURE 574 3% to 10% 33/1

More information

Installation Instructions

Installation Instructions Instructions Aerada 900 Series Futura Faucet With Battery (BIR) Infrared Control S53-284 4" Centerset/Centershank S53-289 Centerset/Centershank w/plate Table of Contents Pre- Information............2 900

More information

Jandy FloPro (FHP) Series Pump Parts Replacement Kit Instructions

Jandy FloPro (FHP) Series Pump Parts Replacement Kit Instructions Replacement Kit Instructions Jandy FloPro (FHP) Series Pump Parts Replacement Kit Instructions FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician, qualified

More information

Instructions. Certifications. Two Handle Kitchen Faucet. Tools Required. Maintenance. Safety Tips. Important Points. Things You May Need.

Instructions. Certifications. Two Handle Kitchen Faucet. Tools Required. Maintenance. Safety Tips. Important Points. Things You May Need. 116874 Chrome less 116864 PVD brushed nickel with 0-K8-CYCH-AD-Z Chrome with 0-K8-CYBN-AD-Z PVD brushed nickel with 0-K8-CNCH-AD-Z Chrome less 0-K8-CNBN-AD-Z PVD brushed nickel less *Image may vary slightly

More information

Audi-Larm TM Audible Alarm: AirHawk II Air Mask

Audi-Larm TM Audible Alarm: AirHawk II Air Mask Audi-Larm TM Audible Alarm: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104323 Doc. 10104323 REPLACEMENT KITS AND PARTS LIST Item P/N Description

More information

Maintenance Information

Maintenance Information Form 16573321 Edition 1 July 2004 Air Grinder Series 61H Maintenance Information Save These Instructions Always wear eye protection when operating or performing maintenance on this tool. Always turn off

More information

Service Handbook. High-Pressure Washer Pump

Service Handbook. High-Pressure Washer Pump Pump 629 9/28/01 3:22 PM Page 1 Service Handbook High-Pressure Washer Pump 3.532-629.0 10.00 Pump 629 9/28/01 3:22 PM Page 2 Pump 629 9/28/01 3:22 PM Page 3 TROUBLESHOOTING OVERVIEW How to Use This Manual

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

REGULATORS ALPHA 8 SECOND STAGE OCEANIC ALPHA 8 SERVICE PROCEDURE

REGULATORS ALPHA 8 SECOND STAGE OCEANIC ALPHA 8 SERVICE PROCEDURE OCEANIC ALPHA 8 SERVICE PROCEDURE This Alpha 8 Service Procedure conveys a list of components and service procedures that reflect the Alpha 8 as it was configured at the time of this writing (2/19/05).

More information

12. FRONT WHEEL/FRONT BRAKE/

12. FRONT WHEEL/FRONT BRAKE/ 12 4.5kgm 0.9kg-m 4.5kg-m 12-0 SERVICE INFORMATION... 12-1 HYDRAULIC BRAKE... 12-10 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-16 FRONT WHEEL... 12-3 STEERING HANDLEBAR... 12-19 FRONT BRAKE...

More information

INSTALLATION & OPERATING INSTRUCTIONS

INSTALLATION & OPERATING INSTRUCTIONS INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.

More information

DURABLA. Fluid Technology Inc. Installation & Maintenance Manual. For Additional Information call

DURABLA. Fluid Technology Inc. Installation & Maintenance Manual. For Additional Information call DURABLA Fluid Technology Inc. Installation & Maintenance Manual For Additional Information call 800-206-4013 610-363-8903 Fax: 610-524-9242 E-mail: durabla@ix.netcom.com Internet: www.dft-valves.com 140

More information

Operating Manual. Model 0.4% Model 1% Model 2.5% Model 5% Model 10% Model 20% Fluid Flow Range: 0.03 gpm to 12 gpm* 7 lph to 2,700 lph*

Operating Manual. Model 0.4% Model 1% Model 2.5% Model 5% Model 10% Model 20% Fluid Flow Range: 0.03 gpm to 12 gpm* 7 lph to 2,700 lph* Operating Manual Model 0.4% Model 1% Model 2.5% Model 5% Model % Model 20% Fluid Flow Range: 0.03 gpm to gpm* 7 lph to 2,700 lph* Injection Range Dosage: 0.025% to 20% 1:4000 to 1:5 Operating Pressure:

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

DP556 Pump. 55:1, Air-operated, Grease. General. Operation. Technical Data. Installation. Mounting with Reinforced Cover (Recommended)

DP556 Pump. 55:1, Air-operated, Grease. General. Operation. Technical Data. Installation. Mounting with Reinforced Cover (Recommended) DP556 Pump 55:1, Air-operated, Grease General The DP556 Pump is a compressed air-operated reciprocating piston pump. This high capacity demand pump is compatible with mineral and synthetic grease and suitable

More information

INSTRUCTION MANUAL. Series PROCUNIER SAFETY CHUCK CO. (Serial Nos. B4870 and higher. (Serial Nos. B9230 and higher

INSTRUCTION MANUAL. Series PROCUNIER SAFETY CHUCK CO. (Serial Nos. B4870 and higher. (Serial Nos. B9230 and higher PROCUNIER SAFETY CHUCK CO. 304 Winston Creek Parkway Lakeland, Florida 33810-2866 Telephone 863-688-0071 FAX: 863-682-6233 Series 29000 (Serial Nos. B4870 and higher (Serial Nos. B9230 and higher INSTRUCTION

More information

Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.

Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. HOUSINGS 7808 Thank You For Choosing Küryakyn! Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding

More information

Model 8329 Table of Contents

Model 8329 Table of Contents SERVICE & OPERATING MANUAL Original Instructions Instructions Sheet: 670991 Model 8329 Table of Contents Engineering Data and Temperature Limitations... 1 Performance Curve... 2 Dimensions... 3 Metric

More information

FOR FUTURE REFERENCE SERIES 93HPS

FOR FUTURE REFERENCE SERIES 93HPS Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps

More information

or OWNER S MANUAL MODEL R

or OWNER S MANUAL MODEL R www.superiorwaterandair.com 801-974-9090 or 800-974-7638 OWNER S MANUAL MODEL 48-1000R Table of Contents Introduction...Page 1 Flow Diagrams...Page 3 The Electro-mechanical Timer Programming...Page 4 Extra

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear

More information

ZTM AND ZTMB ZENNER TURBINE METERS INSTALLATION, MAINTENANCE AND SERVICING

ZTM AND ZTMB ZENNER TURBINE METERS INSTALLATION, MAINTENANCE AND SERVICING ZTM AND ZTMB ZENNER TURBINE METERS INSTALLATION, MAINTENANCE AND SERVICING INSTALLATION 1. The meter is intended for measuring potable, cold water in one direction. 2. The meter is to be installed in a

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts

More information

CONTROL VALVES. Installation, Maintenance & Operating Instructions. Read these instructions carefully before installation or servicing.

CONTROL VALVES. Installation, Maintenance & Operating Instructions. Read these instructions carefully before installation or servicing. KOSO HAMMEL DAHL CONTROL VALVES KOSO HAMMEL DAHL 253 Pleasant Street West Bridgewater, MA 02379 tel: 774.517.5300 fax: 774.517.5230 www.hammeldahl.com Installation, Maintenance & Operating Instructions

More information

Maintenance Information

Maintenance Information 16575219 Edition 4 October 2013 Air Screwdrivers QP1P, QP1S and QP1T Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

WARNING Carefully Read These Instructions Before Use

WARNING Carefully Read These Instructions Before Use DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model

More information

Gas Actuated Valve Supplement

Gas Actuated Valve Supplement Gas Actuated Valve Supplement Product Gas actuated valve Models covered All models fitted to Compac CNG dispensers and Compac Priority Panels Technical parameters Product Maximum inlet pressure Temperature

More information

Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11)

Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11) Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11) Important: Drop 3 drops of oil into the stapler air inlet BEFORE first use. See page 2. Please

More information

Maintenance Information

Maintenance Information 16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Operation and Maintenance Manual

Operation and Maintenance Manual BM / BMA Hydrometers ½ Operation and Maintenance Manual i This manual is intended for use by the users of this equipment. The information contained herein is the property of the Arad Ltd. Dalia and may

More information

INSTRUCTION FOR EFI FUEL PRESSURE GAUGE TOOL

INSTRUCTION FOR EFI FUEL PRESSURE GAUGE TOOL INSTRUCTION FOR EFI FUEL PRESSURE GAUGE TOOL This gauge is now a must have new tool, as 90% of all Big Twins motorcycles have Electronic Fuel injection. (EFI). If you have a customer that is experiencing

More information

The steering column is of a modular construction and features easy to service electrical switches.

The steering column is of a modular construction and features easy to service electrical switches. file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:

More information

Industrial Turbo Meters, Sizes 2" through 6"

Industrial Turbo Meters, Sizes 2 through 6 Industrial Turbo Meters Sizes 2" through 6" TUR-UM-00530-EN-19 (October 2014) User Manual Industrial Turbo Meters, Sizes 2" through 6" User Manual CONTENTS Scope of the Manual 5 Specifications 5 Product

More information

Timing Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A.

Timing Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A. 1997 Chevrolet Cavalier L4-144 2.4L DOHC VIN T SFI Page 1 Timing Chain: Service and Repair With 2 Piece Tensioner (TSB 67-61-22A) Precaution Bulletin No.: 67-61-22A Date: July, 1998 TIMING CHAIN TENSIONER

More information

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery Table 6-1. and solutions with pump operations No Fluid Delivery Fluid level in the reservoir is low. Oil intake pipe or inlet filter is plugged. Air leak in the inlet line prevents priming or causes noise

More information

ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance

ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance OPERATION: (4-2010) The Onyx DAO-ADA pinch valve is an open frame valve without housing enclosure and fails last position on loss of air. This actuator

More information

UOW Series Repair Manual UOW-11 & UOW-T60 Series

UOW Series Repair Manual UOW-11 & UOW-T60 Series UOW Series Repair Manual UOW-11 & UOW-T60 Series 100000 SE Pine St., Portland, OR 97216 800-852-1368 503-254-6600 www.aimco-global.com Contents Page 1. Tools Needed for Repair 2 2. Disassembly and Reassembly

More information

SERVICING INSTRUCTIONS

SERVICING INSTRUCTIONS TSP Series 66 Triplex Plunger Pump SERVICING INSTRUCTIONS TRIPLEX TRIPLEX SERVICING PUMP PROCEDURES Valve Replacement: All inlet and discharge valves can be serviced without disrupting the inlet or discharge

More information

PRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver

PRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location

More information

LEAK TEST PROCEDURE APPLICABLE TO DC3 INTELLI-GRIP LIFTERS MODELS MRT4-DC3, MRTA8-DC3, MRTALP8-DC3 AND PC/P1-DC3 SERIES

LEAK TEST PROCEDURE APPLICABLE TO DC3 INTELLI-GRIP LIFTERS MODELS MRT4-DC3, MRTA8-DC3, MRTALP8-DC3 AND PC/P1-DC3 SERIES LEAK TEST PROCEDURE APPLICABLE TO DC3 INTELLI-GRIP LIFTERS MODELS MRT4-DC3, MRTA8-DC3, MRTALP8-DC3 AND PC/P1-DC3 SERIES TESTING AND MAINTENANCE MUST BE DONE BY A QUALIFIED PERSON KEEP FOR FUTURE REFERENCE

More information