Fixed Rack Mount Kit (24-32 )

Transcription

1 7 December 2010 Fixed Rack Mount Kit (24-32 ) Installation Procedure Supporting the Brocade VDX and VDX **

2 Copyright 2010 Brocade Communications Systems, Inc. All Rights Reserved. Brocade, the B-wing symbol, BigIron, DCFM, DCX, Fabric OS, FastIron, IronView, NetIron, SAN Health, ServerIron, TurboIron and Wingspan are registered trademarks, and Brocade Assurance, Brocade NET Health, Brocade One, Extraordinary Networks, MyBrocade, and VCS are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government. Brocade Communications Systems, Incorporated Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 130 Holger Way San Jose, CA Tel: Fax: info@brocade.com European Headquarters Brocade Communications Switzerland Sàrl Centre Swissair Tour B - 4ème étage 29, Route de l'aéroport Case Postale 105 CH-1215 Genève 15 Switzerland Tel: Fax: emea-info@brocade.com Asia-Pacific Headquarters Brocade Communications Systems China HK, Ltd. No. 1 Guanghua Road Chao Yang District Units 2718 and 2818 Beijing , China Tel: Fax: china-info@brocade.com Asia-Pacific Headquarters Brocade Communications Systems Co., Ltd. (Shenzhen WFOE) Citic Plaza No. 233 Tian He Road North Unit th Floor Guangzhou, China Tel: Fax: china-info@brocade.com Document History Title Publication number Summary of changes Date Fixed Rack Mount Kit (24"-32") Installation Procedure New document. December of 10 Fixed Rack Mount Kit (24"-32") Installation Procedure

3 Contents This document provides instructions to install a Brocade VDX (1U) or Brocade VDX (2U) switch in a 19-inch (48.3 cm) EIA cabinet using the Fixed Rack Mount Kit (24-32 ). The document is organized as follows: Introduction Installation requirements Tool requirements and parts list Installation procedure Introduction The supported switches are listed in Table 1. The switch can be installed so that the port side is either flush with the front rails or recessed from the front rails. A recessed position allows a more gradual bend in the fiber optic cables connected to the switch. TABLE 1 Supported switches Switch height Switch model 1U Brocade VDX U Brocade VDX Installation requirements Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation and operation: Provide space in a 19-inch (48.3 cm) EIA cabinet, as required for the switch type, with a minimum distance of 24 inch (60.96 cm) and a maximum distance of 32 inch (81.28 cm) between the front and back uprights. Verify that the additional weight of the switch does not exceed the cabinet s weight limits. Ensure that an electrical branch circuit with the following characteristics is available: - Required voltage and frequency as indicated in the hardware reference manual ( VAC is always preferred). - Protection by a circuit breaker in accordance with local electrical codes. - Supply circuit, line fusing, and wire size that conform to the electrical rating on the switch nameplate. - Grounded outlet compatible with the power cord and installed by a licensed electrician. Ensure that all equipment installed in the cabinet is grounded through a reliable branch circuit connection. Do not rely on a secondary connection to a branch circuit, such as a power strip. Ensure that the cabinet is mechanically secured to ensure stability. Ensure that the air temperature at the fan inlet is less than 40 o C (104 o F) during switch operation. Ensure that the airflow available at the air vents meets the minimum requirements for the switch. Fixed Rack Mount Kit (24"-32") Installation Procedure 3 of 10

4 Tool requirements and parts list The following items are required to install a switch using the fixed rack mount kit: Clamps or other means of temporarily supporting the switch in the cabinet Phillips #2 torque screwdriver 1/4-inch slotted blade torque screwdriver ATTENTION Use the screws specified for use with the switch. Longer screws can damage the switch. Ensure that the items listed in Table 2 and illustrated in Figure 1 are included in the kit. TABLE 2 Parts list Description Quantity Brackets, front right and left 2 Brackets, short rear right and left 2 Brackets, long rear right and left 2 Screw, 8-32 x 5/16-in., panhead Phillips 12 Screw, 6-32 x 1/4-in., flathead Phillips 8 Screw, x 5/8-in., panhead Phillips 8 Retainer nut, of 10 Fixed Rack Mount Kit (24"-32") Installation Procedure

5 (12x) 5 (8x) 6 (8x) 7 (8x) (8-32 x 5/16 in.) (6-32 x 1/4 in.) (10-32 x 5/8 in.) (10-32) 1 Front brackets, right and left 5 Screw, 6-32 x 1/4-in., flathead Phillips 2 Short rear brackets, right and left 6 Screw, x 5/8-in., panhead Phillips 3 Long rear brackets, right and left 7 Retainer nut, Screw, 8-32 x 5/16-in., panhead Phillips FIGURE 1 Items in the Fixed Rack Mount Kit (24-32 ) Installation procedure ATTENTION The switch must be turned off and disconnected from the fabric during the installation procedure. NOTE Although this document describes how to install both single height (1U) and double height (2U) switches, single illustrations may show either switch type as examples. Complete these tasks to mount the switch: Attaching front brackets Installing the switch in the cabinet Fixed Rack Mount Kit (24"-32") Installation Procedure 5 of 10

6 ! LNK SPD Attaching rear brackets to front brackets Attaching rear brackets to cabinet uprights Attaching front brackets Complete the following steps to attach the front brackets to the switch. 1. Position the right front bracket with the flat side against the right side of the switch (Figure 2). 2. Insert two 8-32 x 5/16-in. screws into the front pair of vertically aligned holes in the bracket and then into the pair of holes on the side of the switch. 3. Insert three more 8-32 x 5/16-in. screws through the holes in the bracket and into the corresponding holes in the switch as shown. 4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lbs. (17 cm-kgs). 5. Repeat step 1 through step 4 to attach the left front bracket to the left side of the switch. SilkWorm 4100 RIGHT IOIOI # REV. B FOXCONN 01/03/ Bracket, front right 4 Screw, 8-32 x 5/16-in., panhead Phillips FIGURE 2 Positioning the front bracket Installing the switch in the cabinet Complete the following steps to install the switch in the cabinet. 1. Position the switch in the cabinet, providing temporary support under the switch until the rail kit is secured to the cabinet. 2. Attach the right front bracket to the right front rack upright using two x 5/8-in. screws and two retainer nuts as shown in Figure 3. 6 of 10 Fixed Rack Mount Kit (24"-32") Installation Procedure

7 ! LNK 3. Attach the left front bracket to the left front rack upright using two x 5/8-in. screws and two retainer nuts as shown in Figure Tighten all the x 5/8-in. screws to a torque of 25 in-lbs. (29 cm-kgs). LEFT scale: 1/8" = 1" RIGHT SilkWorm 4100 IOIOI SPD # REV. B FOXCONN 01/03/ Bracket, front right 7 Retainer nut, Screw, x 5/8-in., panhead Phillips FIGURE 3 Positioning the switch in the cabinet Attaching rear brackets to front brackets Complete the following steps to attach the rear brackets to the front brackets. 1. Select the short rear brackets or the long rear brackets depending on the depth of your cabinet. 2. Position the right rear bracket inside the right front bracket. 3. Attach the brackets using four 6-32 x 1/4-in. screws as shown in Figure 4. Figure 5 shows the long brackets attached to the front brackets. 4. Adjust the brackets to cabinet depth and tighten the 6-32 x 1/4-in. screws to a torque of 9 in-lbs. (10 cm-kgs). 5. Repeat step 1 through step 4 to attach the left rear bracket to the left front bracket. Fixed Rack Mount Kit (24"-32") Installation Procedure 7 of 10

8 5 RIGHT 2 # REV. B FOXCONN 01/03/ Bracket, front right 5 Screw, 6-32 x 1/4-in., panhead Phillips 2 Bracket, short rear right FIGURE 4 Switch with the short rear brackets FIGURE 5 Switch with the long rear brackets (attachment similar to short rear brackets) 8 of 10 Fixed Rack Mount Kit (24"-32") Installation Procedure

9 Attaching rear brackets to cabinet uprights Complete the following steps to attach the rear brackets to the cabinet uprights. 1. Attach the right rear bracket to the right rear cabinet upright using two x 5/8-in. screws and two retainer nuts as shown in Figure Attach the left rear bracket to the left rear cabinet upright using two x 5/8-in. screws and two retainer nuts. 3. Tighten the x 5/8-in. screws to a torque of 25 in-lbs. (29 cm-kgs). 6 RIGHT 2 7 # REV. B FOXCONN 01/03/ Bracket, front right 6 Screw, x 5/8-in., panhead Phillips 2 Bracket, short rear right 7 Retainer nut, FIGURE 6 Attaching the rear bracket to the cabinet upright Fixed Rack Mount Kit (24"-32") Installation Procedure 9 of 10

10 10 of 10 Fixed Rack Mount Kit (24"-32") Installation Procedure