INLET DUCT FOR CISCO 9513 SWITCH Part Number: DIBBC2314S21W

Transcription

1 INLET DUCT FOR CISCO 9513 SWITCH Part Number: DIBBC2314S21W Panduit Corp INSTALLATION INSTRUCTIONS For Either a Net-Access Legacy or Net-Access N-Type Switch Cabinet (CN** OR N**) 9513 Inlet Duct Page1of15

2 COMPONENT GUIDE Note: Upper RH Bracket Has Notches On Top. Upper Seal Plate Upper Left Upper Right (2) Upper Adjustable Brackets Upper Inlet Box Note: Lower RH Bracket Has Notches On Bottom. Side Duct Lower Left Lower Right (2) Lower Adjustable Brackets Lower Seal Plate Lower Inlet Box Rear Duct Hardware Supplied: Tools Needed: -Phillips Head Screwdriver -Socket Wrench -3/8 Socket # 12 Star Washer # Screw # Nut Page2of15

3 INDEX PAGE Removing Side Panel Bumpers... 3 Determine Location of Duct... 4 Upper / Lower Left Installation... 5 Upper / Lower Right Installation... 6 Attaching Foam Seal to Side Duct (For Net-Access N-Type Cabinet)... 7 Side Duct Installation - Day 1 (No Side Panel on Cabinet)... 8 Side Duct Installation - Day 2 (With Side Panel on Cabinet) 9 Separating Side Duct Sections Side Duct Frame Installation Bump Out Installation Duct Seal Installation Upper / Lower Inlet Box Installation Rear Duct Installation Page3of15

4 Removing Side Panel Bumper Unscrew and remove (4) #12-24 screws and (4) # 12 lock washers. Remove Side Panel Bumper. (4) #12 Lock Washers (4) #12-24 Screws Side Panel Bumper Page4of15

5 Determine Location of Duct Ducting requires (20) rack units for installation. Duct components can be installed before or after switch installation and are NOT designed to support the switch. The front equipment rails need to be in the full forward position. Rear equipment rails need to be located 24.25" to 26.0" from the front rails. Due to physical constraints posed by the front-to-back frame beams on the legacy Net-Access Cabinet, the inlet duct can only be installed in one location. For new Net-Access switch cabinets (N***), the only restriction is that 3 RU must be left open above and below the switch for inlet duct 24.25"- 26.0" from Outside of Rails 2 2/3 RU Upper Inlet Box 20 RU 14 1/3 RU Front Equipment Rail Front to Back Support 3 RU 2 RU Lower Inlet Box Page5of15

6 Upper / Lower Left Installation Attach upper adjustable bracket to upper left hand bracket with (2) #10-32 nuts. (Leave nuts loose.) Attach lower adjustable bracket to lower left hand bracket with (2) #10-32 nuts. (Leave nuts loose.) Measure distance between front and rear rails. Adjust brackets to fit front and rear rail distance. (Tighten nuts on brackets that were left loose.) Install (1) upper left hand bracket with (4) #12-24 screws and (4) #12 star washers. (Leave screws loose until Inlet Box is installed.) Install (1) lower left hand bracket with (4) #12-24 screws and (4) #12 star washers. (Leave screws loose until Inlet Box is installed.) Equipment Rail Spacing Upper Adjustable Bracket Upper Left Upper Left Equipment Rail Spacing Adjustment Nuts (8) # Screws (8) # 12 Star Washers Lower Left Lower Left Adjustment Nuts Lower Adjustable Bracket Page6of15

7 Upper / Lower Right Installation Attach upper adjustable bracket to upper right hand bracket with (2) #10-32 nuts. (Leave nuts loose.) Attach lower adjustable bracket to lower right hand bracket with (2) #10-32 nuts. (Leave nuts loose.) Measure distance between front and rear rails. Adjust brackets to fit front and rear rail distance. (Tighten nuts on brackets that were left loose.) Install (1) upper right hand bracket with (4) #12-24 screws and (4) #12 star washers. (Leave screws loose until Inlet Box is installed.) Install (1) lower right hand bracket with (4) #12-24 screws and (4) #12 star washers. (Leave screws loose until Inlet Box is installed.) Upper Right Upper Adjustable Bracket Adjustment Nuts Upper Right Equipment Rail Spacing (8) # Screws Lower Right Lower Adjustable Bracket Lower Right (8) # 12 Star Washers Adjustment Nuts Equipment Rail Spacing Page7of15

8 Attaching Foam Seal to Side Duct. (For Net-Access N-Type Only) Attach one strip of foam seal to flange on front of side duct. Foam Seal Side Duct Side Duct Flange Page8of15

9 Side Duct Installation - Day 1 Side Duct Installation Slide (4) studs on side duct into (4) slots on right hand side brackets. Secure side duct to brackets with (4) #10-32 nuts. (No Side Panel on Cabinet) Side Duct (4) Studs (4) #10-32 Nuts Bracket (4) Slots Page9of15

10 Side Duct Installation - Day 2 (With Side Panel on Cabinet) Separating Side Duct Sections Remove (4) #10-32 nuts from side duct assembly. Separate side duct frame from bump out. Side Duct Frame Bump Out (4) #10-32 Nuts Page 10 of 15

11 Side Duct Frame Installation From the rear of the cabinet insert the side duct frame into the cabinet. Slide (4) studs on the inside of the side duct frame into the slots on the right side brackets. Secure side duct frame to right side brackets with (4) #10-32 nuts. (4) #10-32 Nuts (4) Inside Studs (4) Slots Page 11 of 15

12 Bump Out Installation Insert the bump out from the rear of the cabinet. Slide the notches on the bump out on to the studs on the top and bottom of the side duct frame. Secure the bump out to the frame with (4) #10-32 nuts. (4) #10-32 Nuts Side Duct Frame Bump Out (4) Studs (4) Slots Page 12 of 15

13 Duct Seal Plate Installation Slide upper seal plate studs through the holes in the top of the side duct and bracket. Secure seal plate to side duct with (2) #10-32 nuts. Repeat process for lower seal plate. Upper Seal Plate (2) #10-32 Nuts (2) #10-32 Nuts Lower Seal Plate Page 13 of 15

14 Inlet Box Installation Slide upper inlet box into rails on the upper brackets so that studs on the upper brackets pass through the holes on the inlet box flanges. Slide lower inlet box into rails on the lower brackets so that studs on the lower brackets pass though the holes on the inlet box flanges. Secure the inlet boxes to the brackets with (4) #10-32 nuts. Upper Inlet Box Lower Inlet Box Bracket Stud (4) #10-32 Nuts Inlet Box Flange. Page 14 of 15

15 Rear Duct Installation Slide the studs on the side of the rear duct into the slots on the sides of the bottom inlet box. Make sure bottom of the rear inlet duct slides into folds on the bottom inlet duct. Secure the rear duct in place with (2) #10-32 nuts. Tighten all screws that were previously left loose. (2) Slots Bottom Inlet Duct Folds Rear Duct (2) #10-32 Nuts Bottom Inlet Box (2) Studs For Instructions in Local Languages and Technical Support: Page 15 of 15 Phone: