Serial Number 6661 Build Date Full overhaul and modification in 2011

Transcription

1 Miner Equipment Information Plant Number CM0012 Manufacturer Joy mainframe modified by WDS Model 12CM30 - Plough Serial Number 6661 Build Date Full overhaul and modification in 2011 Minimum cutting height 2,200mm roof bolter highest point Maximum cutting height 3,800mm Minimum tramming height 1,700mm operator protective shield inside roof bolters note would need alternative hydraulic header tank fitted at this height Electrical Code D last overhaul November 2011 WDS Mackay Cutter motor size and last overhaul 2 x 115kW November 2011 Pump motor size and last overhaul 2 x 45kW May 2011 Gathering motor last overhaul Traction motor size and last overhaul 2 x 60kW DC November 2011 Rear drive motor last overhaul October 2010 Radio system type Pempek Gas system details Gasguard Lighting 4 x forward facing ATF351, 3 Burnbrite area lights each side, 1 x ATF351 rear facing Cutter head width and pick size 5.2m extended. Joy J35 blocks with scroll Cutter head Generally good oil weeping from RH outer drum Gathering spinner East / West chain Apron / Conveyor deck minimal cutting since manufacture Conveyor chain and sprocket Cincinnati DA months of use Intermediate and rear conveyor Decks good RH rear drive gear case missing Track Track runner Machine pin and bush Machine cylinder Generally good LH conveyor lift leaking Hydraulic pumps Hydraulic valves Rexroth M4-15 with FLP solenoids Hydraulic hosing OK some hose covering affected by Water valving Hydraulic Controls pilot valves Side Platforms fold up 750mm high Bolter platforms Large platform good Operator platform shield hydraulic extendable Safety head stops Joy light weight type Safety conveyor stop Gun barrel style Roof Support TRS 2 stage cylinder Roof Support Bolter type HFX280 angled gripper headplate Roof Support- Motor type Roof Support Control valves Joy ICM2.5 mast mounted Rib support Bolter type HFX190 with front entry gripper headplate and vertical lift Rib support Motor type

2 Rib support Control Valves Joy ICM3 cabinet mounted Strata Support - other Nil Paint Condition Paint flaking / rusting Last hire sites Mannering 5 months usage since overhaul in 2011 Other Information Fixed mesh slide 2,250mm high. Header tank fixed to mainframe. 1,000V incoming extension cable to LH side

3 Miner Equipment Information Plant Number CM0014 Manufacturer Joy Waratah modified Model 12CM12 B or D height Serial Number 4490 Build Date 1995 Minimum cutting height B height 2,200mm, D height 2,645mm Maximum cutting height B height 3,755mm, D height 4,685mm Minimum tramming height 2,100mm Electrical Code D last overhaul February 2009 WDS Mackay Cutter motor size and last overhaul 170kW November 2010 Pump motor size and last overhaul 2 x 45kW February 2009 Gathering motor last overhaul October 2010 Traction motor size and last overhaul 35HP DC - February 2009 Rear drive motor last overhaul Radio system type Pempek Gas system details Trolex Lighting 4 x ATF351 front, 2 x Burnbrite area lights each side, 1 x ATF351 rear Cutter head width and pick size Supplied with 3.3m narrow head, J25 pick blocks Cutter head Used Gathering spinner Worn gathering boxes removed and sitting on pallets in store East / West chain Apron / Conveyor deck Minimal wear Conveyor chain and sprocket Cincinnati chain 60% worn. Chain incomplete and drive sprocket missing Intermediate and rear conveyor Wear on deck plates Track Cleats worn Track runner Require build up / crack repairs Machine pin and bush Worn visible clearances. Lack of lubrication Machine cylinder Chrome rusting and some leaks. Apron lift cylinders not suitable for narrow head apron / head Hydraulic pumps 2 x Danfoss 211LPM pumps Hydraulic valves Commercial MCS with spool monitoring requires upgrading Hydraulic hosing Intact but due for replacement Water valving Hydraulic Controls pilot valves Side Platforms 2 piece Fold down fair 500mm high Bolter platforms Hydraulic extend some wear / damage Operator platform shield Fixed shield Safety head stops Dual gun barrel pins inbuilt to mainframe in throat Safety conveyor stop Joy prop style Roof Support TRS Joy cylinder require overhaul Roof Support Bolter type HFX gripper Roof Support- Motor type Roof Support Control valves Joy ICM2.5 mast mounted Rib support Bolter type HFX190 front entry gripper chains and rods poor

4 Rib support Motor type Rib support Control Valves Strata Support - other Paint Condition Last hire sites Other Information Joy ICM2.5 cabinet mounted Hydraulic Control intensifier Poor Wambo, Broadmeadow, Beltana Wide head cutter boom and apron removed. Narrow, fixed head and apron available suitable for 3,300mm wide cut. Fitment of this apron and cutter boom will require bolter and platform removal, apron lift cylinder mount modification.

5 Miner Equipment Information Plant Number CM0015 Manufacturer Joy Model 12CM32 - B PPM Serial Number 6678 Build Date 2002 Minimum cutting height 2,800mm roof bolter highest point Maximum cutting height 3,800mm Minimum tramming height 2,200mm Electrical Code D last overhaul February 2010 WDS Mackay Cutter motor size and last overhaul 2 x 170kW February 2010 Pump motor size and last overhaul 2 x 45kW December 2009 Gathering motor last overhaul Traction motor size and last overhaul 2 x 60kW DC February 2010 Rear drive motor last overhaul March 2010 Radio system type Joy JNA2 Gas system details Austdac Trolex Lighting ATF351 x 4 forward facing, 3 Burnbite area lights per side, 1 x rear facing ATF351 light Cutter head width and pick size 5.2m extended. Joy J30 blocks Cutter head Disassembled repairs needed as per W119 reports Gathering spinner East / West chain 25% worn, adjuster blocks 70% worn. East / West gearcase recently overhauled Apron / Conveyor deck 80% worn Conveyor chain and sprocket Used Joy chain sprockets worn Intermediate and rear conveyor Worn and corroded Track Appear good Track runner Machine pin and bush Some wear Machine cylinder Wear and chrome corrosion. Hydraulic pumps Danfoss variable displacement Hydraulic valves Danfoss valve bank, IVM Hydraulic hosing Corroded hose ends Water valving IVM Side Platforms 2 piece fold out 750mm high Bolter platforms Large hydraulic extend Operator platform shield Hydraulic extension arops Safety head stops Missing Safety conveyor stop Gun barrel style Roof Support TRS Joy type chrome on rods corroded Roof Support Bolter type HFX310 x 4, front entry gripper headplates - overhauled Roof Support- Motor type Roof Support Control valves Joy ICM mast mounted Rib support Bolter type HFX190 with front entry gripper headplate good Rib support Motor type Rib support Control Valves Joy ICM2 cabinet mounted ICM3 upgrade cabinets

6 Strata Support - other Paint Condition Last hire sites Other Information available 1 x hydraulic intensifiers Corrosion across all steel components Austar Cross over incoming cable. Machine partially stripped down after last hire

7 Miner Equipment Information Plant Number CM0016 Manufacturer Joy Model 12CM32-B-5.2-PPM Serial Number 6698 Build Date August 2005 Minimum cutting height 2,450mm TRS lowest height Maximum cutting height 3,880mm Minimum tramming height 1,900mm operator shield near bolter Electrical Code D last overhaul Cutter motor size and last overhaul 170kW August 2011 Pump motor size and last overhaul 2 x 45kW March 2013 Gathering motor last overhaul October 2011 Traction motor size and last overhaul 60kW AC - March 2013 Rear drive motor last overhaul January 2014 Radio system type Gas system details Lighting Cutter head width and pick size Cutter head Gathering spinner East / West chain Apron / Conveyor deck Conveyor chain and sprocket Intermediate and rear conveyor Track Track runner Machine pin and bush Machine cylinder Hydraulic pumps Hydraulic valves Hydraulic hosing Water valving Side Platforms Bolter platforms Operator platform shield Safety head stops Safety conveyor stop Roof Support TRS Roof Support Bolter type Roof Support- Motor type Roof Support Control valves Rib support Bolter type Rib support Motor type August 2011 WDS Mackay - POE0 completed December 2014 Joy JNA2 Gasguard 4 x ATF351 front, 2 x Burnbrite area lights each side, 1 x ATF351 rear 5.2m width, Joy J35 pick blocks Worn one wear plate missing Skin on conveyor in apron worn through. Hardfacing on apron worn down Joy chain 60% worn. Drive sprocket 30% worn Wear on deck plates OK replaced 18 months ago Worn visible clearances. Lack of lubrication Some leaks on cylinders Variable flow Joy IVM need overhaul Intact but due for replacement Joy IWM need overhaul Folder down fair Hydraulic extend some wear / damage Fixed shield LH side missing Dual pins inbuilt to apron Gun barrel style Joy original HFX310 front entry gripper chains and rods good Joy ICM2.5 mast mounted HFX190 front entry gripper chains and rods poor

8 Rib support Control Valves Strata Support - other Paint Condition Last hire sites Other Information Joy ICM2.5 cabinet mounted Nil Poor Ensham, Oaky North, Oaky No1, Beltana, Metropolitan Recovery pendant and recover tow points fitted

9 Miner Equipment Information Plant Number CM0011 Manufacturer Joy Model 12CM30-B Serial Number 6618 Build Date 2001 disassembled for overhaul in 2012 Minimum cutting height 2,200mm roof bolter highest point Maximum cutting height 3,800mm Minimum tramming height 1,768mm operator protective shield inside roof bolters note would need alternative hydraulic header tank fitted at this height Electrical Code D last overhaul April 2009 WDS Mackay. AS3800 started in 2013 however not signed off Cutter motor size and last overhaul 2 x 170kW ex CM18 March 2011 Pump motor size and last overhaul 2 x 45kW ex CM18 - November 2011 Gathering motor last overhaul Traction motor size and last overhaul 2 x 60kW DC Ex CM18 - May 2012 Rear drive motor last overhaul March 2016 Radio system type Pempek Gas system details Nil Lighting ATF351 forward facing and Burnbrite areas lights qty to be determined Cutter head width and pick size 5.2m extended. Joy J30 blocks Cutter head Disassembled repairs needed as per W074 reports Gathering spinner East / West chain Used Apron / Conveyor deck repairs completed to apron hard facing other deck work to be completed Conveyor chain and sprocket Used Joy chain sprockets worn Intermediate and rear conveyor Repairs underway fan section of intermediate conveyor replaced and hard facing complete. Wear strips and deck repairs to be completed Track Used cleat height appears good Track runner Machine pin and bush Missing pins and bushes removed Machine cylinder Some cylinders overhauled 2 x shear cylinders and 1 x apron missing Hydraulic pumps - overhauled Hydraulic valves Need overhaul Danfoss valve bank Hydraulic hosing Missing new hosing required Water valving Require overhaul Side Platforms Require overhaul some may be missing Bolter platforms Large platform require overhaul Operator platform shield Missing Safety head stops Missing Safety conveyor stop Missing Roof Support TRS Require overhaul Roof Support Bolter type HFX280 front entry gripper headplate require overhaul.

10 Only LH side cradle available and 2 of the original 4 bolters Roof Support- Motor type Roof Support Control valves Joy ICM2 mast mounted require overhaul Rib support Bolter type HFX190 with front entry gripper headplate require overhaul Rib support Motor type Rib support Control Valves Joy ICM2 cabinet mounted 1 of 2 available Strata Support - other 2 x hydraulic intensifiers require overhaul Paint Condition Major components blasted and painted Last hire sites Integra, Austar, Metropolitan Other Information Stripped down for major overhaul that was stopped in 2013