RECYCLING & PLASTICS PLANT EQUIPMENT AUCTION FOR FINANCIAL INSTITUTION

Transcription

1 The Proxio Group Ltd RECYCLING & PLASTICS PLANT EQUIPMENT AUCTION FOR FINANCIAL INSTITUTION CUMBERLAND GRANULATORS - SWECO SIFTERS - BALERS - CYCLONES - BLOWERS - EXTRUDERS - FILTER PRESSES - DRYERS - AND MUCH MUCH MORE Cleveland Ohio United States Ended Mar 14, :41pm EST Lot Description 1 Unused 300 ton Trane chiller, model CVHE400, type CVHE040KA4XWRSNLS5568B6MCA RD1OOGOLSW0003C100B, water cooled, 3 stage compressor, R123 refrigerant, 244 kw, 2300 volt, serial# L09L02312, built 11/2009.***Loading Fee $950.00*** 2 Line Control Panel with 400A, 3 phase breaker 3 Heavy Duty Metal Cutting Band Saw, 40" deep throat, 5HP/ /440v 4 inclined belt conveyor, 48" wide x 360" long smooth belt, driven by 3 hp, 230/460 volt.***loading Fee $250.00*** 5 Roach smooth belt conveyor, 36" wide x 288" long, driven by 2 hp, 230/460 volt motor, serial# ***Loading Fee $100.00*** 6 W.E.S box dumper, 50" wide x 42" deep x 54" high, hydraulic actuation, on 72" high carbon steel frame. 7 Roach belt conveyor, 60" wide x 360" long, driven by 2 hp, 230/460 volt motor, serial# ***Loading Fee $100.00*** 7A 48" x 48" x 44" Deep Carbon Steel Hopper on wheels 8 cleated belt conveyor, 36" wide x 246" long, with gearbox less motor.***loading Fee $150.00*** 9 Meber band saw, approximately 24" cutting area, approximately 2 hp drive " wide x 19' long smooth belt conveyor, no motor 11 Hydracolor Volumetric Blender/Feeder, Model MM-300-3, carbon steel construction, 3 material design, with drives and controls, 10'6" overall height.***loading Fee $150.00*** 12 Hapman Pneumatic Loader, stainless steel construction with blower, mounted on approximately 55 cu. ft. stainless steel hopper, 4' X 4' X 3" straight side X 2' cone bottom with 8" slide gate valve and 6" rotary air lock with /460 Volt motor, Serial No. H HE.***Loading Fee $100.00*** 13 Toyota hand truck with Battery Handling Systems (BHS) battery carrier, BHS model ATC-36 Mag, Toyota model# 6HBW20, serial# 20326, 4000# capacity, magnetic securing mechanism with hydraulic controls, 36" wide x 42" carrier with rollers, BHS serial# ID

2 14 West Salem Machine bale breaker, model 15-60, with approximately 48" wide x 174" long feed conveyor, with (3) 7- blade choppers, (1) 14-blade saw blade shaft, less drive, serial# ***Loading Fee $300.00*** 16 Process Control Corporation material push/pull vacuum pump with associated controls. 17 weir style float / sink tank, carbon steel construction, approximately 7'6" wide x 13' long x approx 10' high, dual cone bottom hoppers on legs 18 Toyota hand truck with Battery Handling Systems (BHS) battery carrier, BHS model ATC-36 Mag, Toyota model# 6HBW20, serial# 19137, 4000# capacity, vacuum securing mechanism with hydraulic controls, 36" wide x 42" carrier with rollers, BHS serial# AX Gardner Denver air compressor, model EDF99D, 125 maximum psi, 75 hp motor, 460 volt, with control cabinet and air cooling, serial# S031981, built 11/ " diameter x 39' long drum dryer, carbon steel construction, with internal baffles, 8" discharge on bottom end, approximately 45" discharge height, on frame, with approximately 2 hp drive motor, less belts and burner assembly***loading Fee $400.00*** 24 Conair stand pelletizer, model 3508, 8" wide helical rotor, pull roll assembly with rubber pull roll, 15 hp, 230 volt motor, serial# ***Loading Fee $100.00*** " Sterling extruder, 24:1 L/D, electrically heated, air cooled, with 40 HP DC motor with SCR controller, 3.95:1 gearbox ratio, 100 RPM output speed, (4) barrel zones, (2) die zones, with control panel, serial no , Motor HP: 40***Loading Fee $300.00*** 27 inclined, dewatering twin screw conveyor, carbon steel construction, approx. 35" wide x 14' long trough, 15" diameter screws, individually driven with twin 3 HP motors, two side over flow sluice outlets, dual 3" trough drains.***loading Fee $300.00*** 29 Sterling blower, model 13 MS, no motor, 14" inlet/outlet, serial# 18465, built Conair granulator, model CW1824, 18" x 24" feed opening, 3 knife open rotor, 25 hp, 460 volt motor, with sound enclosure, serial# , built 2007.***Loading Fee $300.00*** 31 30" W x 12' L Hytrol Belt Conveyor***Loading Fee $100.00*** hp Conair blower system, model CR2000, indoor use, in enclosure, 480 volt, in cabinet, with controls, serial # Sterling run off table, 70" wide x 120" long, with dual parallel 25" wide belts, driven by estimated 2 hp motor, with 50" wide inclined air table.***loading Fee $100.00*** 34 Chicago blower, size 24-1/2, 25 hp blower, 460 volt, 24" inlet, 21" x 23" outlet, serial# , built " Diverter Valve, carbon steel construction, with hydraulic pump. 37 pipe coiler, approx. 24" wide x 18" diameter hub, approx. 82" diameter coil take up, 3/4 HP, 90 volt DC motor with controllers.***loading Fee $100.00*** 39 Process Control gravametric blender, model XBECYUKJED, 4 material with loaders and receivers, rated up to 650#/hour, serial# , new 1997.***Loading Fee $100.00***

3 40 cyclone dust collector, carbon steel construction, approximately 36" diameter x 20" straight side x 42" cone bottom, 8" inlet, 6" outlet. 41 Inclined Screw Conveyor, with 8" screw x 148" in length, discharge height 58", approx 1 HP. 42 Una Dyn Hopper Dryer with Heater and Blower, 200# Hopper with receiver. 44 Novatech hopper dryer system, model POD-250-B, rated 250 CFM, with blower, controls, 230 volt, with ten (10) Novatech hopper receivers model PEE-WEE with blowers, dryer serial# ***Loading Fee $150.00*** 45 Roach cleated belt conveyor, 36" wide x 288" long, with gearbox less motor, serial# ***Loading Fee $200.00*** 46 Weir style float sink tank, carbon steel construction, approximatelyt 110" x 100" x 72" deep x 65" cone bottom chamber, on legs with approximately 15' overall height.***loading Fee $200.00*** 47 Gala Industries underwater pelletizing system with Gala model 8MUP cutting head with 5 hp XP motor, with oil heated die plate and water box, with Gala TWS40 tempered water circulation system, with Gala centrifugal pellet dryer model 12 BF/S, system rated Class I, Div. II, serial# ***Loading...[more] 48 Mitts & Merrill Hog Mill model 13 CSD 15" x 18" feed opening, 30" diameter rotor, belt driven by 100 hp, 460 volt motor, with infeed belt conveyor, discharge blower and stainless steel cyclone.***loading Fee $250.00*** 49 34" diameter 39' long drum dryer, carbon steel construction, with internal baffles, 7" x 9" discharge, approximately 56" discharge height, on frame, with approximately 2 hp motor drive motor, with GSI 2.1 million BTU propane fired heater.***loading Fee $400.00*** 50 60" Sweco screen, model XS60S888LKUE, stainless steel construction, single deck, on base with 2.5 hp, 460 volt motor, serial# A11/ Yale hand truck with Battery Handling Systems (BHS) battery carrier, Yale model MPW060LEN , serial# A897N02853B, vacuum securing mechanism with hydraulic controls, 36" wide x 42" carrier with rollers " Russel Finex sieve, model 26070LDAES, stainless steel construction, single deck, 1.5 hp, 230/460 volt motor, on base with casters, serial # RAS160, built NPK vacuum system, type HITB-06E 220/R6 HL, carbon steel construction, with 10 hp, 230 volt blower, rated 6 cu meter/minute, 2200 MMAQ with receiver and dust filter mounted on unitized base, serial# W-00-26, new Gardner Denver air compressor, model EDE99K04, 125 maximum psi, 50 hp motor, 460 volt, with control cabinet (no interface or internals), air cooling, serial# S011807, built 3/ gallon plastic tank, 64" diameter x 34" straight side, hole cut in top, 2" side bottom outlet, on carbon steel frame, serial# , built 12/ Float sink tank, carbon steel construction, 96" long x 60" wide x 38" triangular bottom.***loading Fee $200.00*** 57 Sterling blower, model 1120FV, no motor, 12" inlet/outlet, serial# A, built Herbold Granulator, Model SMS45/80, 18" x 30" grinding chamber, 150 H.P. drive motor, 460 volts, 5 knife rotor, 3 bed knives, additional flywheel conveyor feed hopper, 10 H.P. blower, buit 1988.***Loading Fee $300.00***

4 59 13' Universal Industries bucket elevator, model# C6-600-ED, carbon steel construction, approximately 15' discharge height, plastic belts and buckets, 1.5 hp, /460 volt motor drive, serial# 62458, built Process Control gravametric blender / feeder, carbon steel construction, 4 material with loaders and receivers, 115 volts***loading Fee $100.00*** 61 Process Control Corporation material push/pull vacuum pump with associated controls.***loading Fee $100.00*** 62 Killion lab multi-filament extrusion system with One(1) 1" Killion extruder, 24:1 L/D, electrically heated, air cooled, jacketed feed section, 3 HP DC motor with SCR controller, 3 barrel zones, serial no F, one (1) used gear pump, One (1) used multi-filament dies / spin pack, on base with cont...[more] 64 conveyor, approxmately 36" wide x 252" long smooth belt, with 2 hp, /460 volt drive. 65 Sterling blower, 10 hp blower, 230/460 volt, 10" inlet/outlet. 66 Stokes oil seal vacuum pump, model , rated 30 cfm with 1.5 hp xp motor, lot# , serial# Keaser Air Compressor, Model ICS90, 75 H.P. 460 volt motor, PSI, air cooled, 3439 service hours, load hours, Serial No , New Acrison volumetric feeder, model BDF-4-N/2, stainless steel construction, twin conditioning screws driven by independent 3 hp, 230/460 volt xp motor drives, 4" discharge screw driven by approximately 7.5 hp xp motor drive, 5" diameter x 28" long discharge screw housing, 48" diameter top opening, (2)...[more] 69 Flex-Weigh Corp balance, model PGC-1318, approximately 13" x 18" stainless steel top, rated 200# capacity,.05 accuracy, with digital readout, serial# kw Onan genset, model 20.Oes-1sr/156203, standby, 60 hertz, 1800 rpm, 18.5 kw, 23 kva, 3 phase, 13.5 kw, 6.7 kva, single phase, 120/208 volt at 64 amps to 277/480 volt at 23 amps, natural gas fired with Ford engine, with transfer switch in cabinet, serial# E ***Loading Fee $100.00*** 71 60" diameter Macon screener, single deck, stainless steel rings, 2.5 HP 460 volt motor, serial # AEC Loader, single material with 24 cu. ft. stainless steel hopper with loader and Dual AEC AF-1 Additive Feeders, one with motor, one without motor, and bunting magnet. 73 Baker-Perkins Ko-Kneader Co-Extrusion Pelletizing Line consisting of the following: ONE (1) Used Baker-Perkins Ko-Kneader, Model UPK-150-UEM, 150 MM diameter screw, 10:1 L/D, split barrel, jacketed for 300 PSI, 250 H.P. drive, screw RPM with Size 6 Baker-Perkins Crammer Feeder with 10 H.P. Dr...[more] 74 Single shaft shredder, approximately 54" wide single shaft, Model ESS-1500, approximately 14" diameter, driven by approximately 100 hp, 460 volt motor drive, approximately 55" wide x 62" long infeed, with hydraulic ram driven by onboard hydraulic power pack.***loading Fee $500.00*** 75 Day Ribbon Blender, 36 cu. ft. working capacity, stainless steel construction, 30" wide x 78" long trough, double ribbon, 6" center bottom outlet, short stands, outboard roller bearings packing glands, complete with 10 H.P. drive, /444 volt, Serial No ***Loading Fee $100.00***

5 hp blower, carbon steel construction, 200 hp, 460 volt, 3570 rpm direct connected motor, 8" x 44" diameter housing, 8" x 16" outlet, 12" x 36" inlet with baffles no base.***loading Fee $100.00*** 77 Tri-Clover centrifugal pump, model SP218M , stainless steel construction, 2" x 1.5" on base with 25 HP 460 volt 60 Hz motor, serial# V Model S45 Foremost Granulator, 16" x 45" feed opening, 3 knife closed rotor, 2 bed knives, feed hopper with dual 50 H.P. 230/460 volt motors, with 20 H.P. blower discharge, Serial No ***Loading Fee $200.00*** 79 Process Control gravametric blender / feeder, model MWBSGSXS01, carbon steel construction, 4 material with loaders and receivers, serial# 20621A, new 1987.***Loading Fee $100.00*** 80 8" Hartig Extruder, electrically heated, air cooled barrel, 40:1 L/D, vented barrel, 700 HP DC motor through Lufkin gearbox, 11:56:1 ratio, approximately 112 rpm screw speed, less control panel and motor scr, order# R-5168, built 1985.***Loading Fee $750.00*** 81 Weir style float sink tank, carbon steel construction, approximately 110" x 100" x 72" deep x 65" cone bottom chamber, on legs with approximately 15' overall height***loading Fee $200.00*** 82 Piqua Engineering baler, 48" high x 75" wide bales, with 10 hp hydraulic pack mounted on unit.***loading Fee $200.00*** 83 60mm Plastex Single Screw Extruder, Type EX60, 24:1 L/D, electrically heated, air cooled, jacketed feed section, 29 KW DC motor, 13.6:1 gear box ratio, integrally mounted 7 zone control panel with West Temp Controllers and SCR Controller, Serial #3018, New 1998.***Loading Fee $300.00*** 84 Falcon Mark I hydraulic power pack, volt or 7.5 hp 460 volt motor, with manifold, 41" wide x 72" long x 30" high reservoir " W x 19' L Belt Conveyor 89 PTR Baler/Compactor, model 3400HDES, 30" deep x 61" wide, top mounted 15 hp hydraulic pack, 460 volt, 3 phase, serial# , built 2011.***Loading Fee $200.00*** 90 Hydracolor Volumetric Blender/Feeder, Model MM-300-3, carbon steel construction, 3 material design, with drives and controls, 10'6" overall height.***loading Fee $150.00*** hp Buffalo Blower, size 45, type HW, carbon steel construction. 93 3/4" extruder, 18" barrel, 24:1 L/D, (3) heating zones and (1) die zone, electricall heated, air cooled, driven by 1.5 hp motor, with motor and temperature controls.***loading Fee $150.00*** 94 Belt conveyor, 11" Wide x 152" long belt, with 3/4 HP Electric Drive, 220V.***Loading Fee $150.00*** 95 Conair granulator, model CE912, with 6 mm screen, 12" x 12" feed throat size with starter box, serial# , built Hisey-Wolfe Machinery Pedestal Grinder, 10HP Drive. 97 EDI 8" Flex Lip Die, Model H40, with auto flex mechanism, 40 MM die gap, removable lower lip, on stand, serial#

6 98 Mitts and Merril hog mill, model 15 CSE, rear discharge, 20" x 27" feed opening, 30" diameter rotor with 150 hp, 460 volt direct coupled motor, 1180 rpm, on unitized base with feed hopper.***loading Fee $300.00*** 99 Atlas Copco oil free air compressor, model ZT22, 30 hp, 125 psi, 113 cfm with controls, hours, serial# AIF with Pioneer dual desiccant air dryer, model PHL-100, rated 100 psi at 110 cfm, serial# 6153B5D020.***Loading Fee $100.00*** 100 (5) Pallets of starter and control panels 101 Used Gorman-Rupp 5 hp centrifugal pump, model T3A3-B, carbon steel construction, belt driven, serial# Used (2) 10 hp Veriflow centrifugal pumps, model 1626, carbon steel construction, size 3x3x Used Aluminum diaphragm pump, 3" Inlet and Outlet 104 Used Aluminum diaphragm pump, 3" Inlet and Outlet 105 (3) Used 10 hp Veriflow centrifugal pumps, model 1626, carbon steel construction, size 3x3x (2) Used Bag Houses, carbon steel construction, (4) 16" inlets and 16" outlet. 107 Used Bag House, carbon steel construction, (8) 16" inlets and 22" outlet. 108 Used Blades bag house, type FHSM, carbon steel construction, (16) 16" inlets and 34" outlet. 109 Used Blades bag house, type FHSM, carbon steel construction, (16) 16" inlets and 34" outlet. 110 Used Blades bag house, carbon steel construction, (16) 16" inlets and 34" outlet. 111 Used Blades bag house, carbon steel construction, (16) 16" inlets, no outlet section. 112 Used Flex-Weigh platform scale, model FCB 4848, 48" x 48" platform, 5000# capacity, with readout. 113 Used Metro floor scale, 28" x 28", on wheels. 114 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide. 115 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide. 116 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide. (Belt not part of Lot) 117 Used Battery Handling Systems battery charging storage rack, model BS-30-2-LE, 64" long x 40" wide. 118 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide, damaged rollers. 119 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide, with 24 volt charger.

7 120 (3) Used batter chargers, 9.7 kva, 36 V, 800 A output 121 (2) Used batter chargers, 9.7 kva, 36 V, 800 A output 122 Used 20 hp Blades blower, model 1120 FV, carbon steel construction, belt driven, 12" inlet and outlet, serial# Used Breaker panel, 480 volt, 600 amp, 3 phase. 124 Used Ensign Equipment model " x 156" long screw conveyor, carbon steel construction 125 Used Power switch box, on stand. 126 Used 55" diameter stainless steel hopper, cone bottom. 127 Assorted used Sweco screener parts 128 Used Battery Charging Storage Rack, model B533-2X, 76" long x 40" wide, with (2) 36 volt chargers. 129 (3) Used 3 hp Sterling blowers, direct driven 130 (2) Used 3 hp Sterling blowers, direct driven, with (1) used pedestal grinder. 131 Lot of power switch boxes with Ohaus scale platform, no controls 132 Lot of (5) Used battery chargers, model# TST-D, 36 volt, 800 Amp output (1 Damaged) 133 Used 5hp Buffalo blower, size 25, carbon steel construction. 134 Used Kason sifter base parts 135 Used Eriez vibrating conveyor, model HS SG, 18" wide x 52" long. 136 Lot of Used (2) Tinius Olsen Extrusion Plastometers, with (1) Kayness Extrusion Plastometer 137 Used 42" x 42" bin hopper, carbon steel construction, 20" straight side, cone bottom. 138 AEC Whitlock Blender, Model OS-067, currently 2 material can handle up to 4 material, with Model SHR-08 and SHR-16 vacuum hoppers, rated up to 350#/hr., Serial No. 30F0394C0P16910F***Loading Fee $100.00*** 139 MGB Engineering densifier, bottom driven with estimated 200 hp 460 volt 60 hz 3 phase motor, side discharge with flush valve, on base.***loading Fee $300.00*** 140 Gala underwater pelletizing cutter head, model 5 MUP, driven by 2 hp, 230/460 volt motor, (1) die plate on stand.***loading Fee $150.00***

8 141 14" diameter x 12 long inclined rinse / wash conveyor, carbon steel construction, with two bottom clean out doors.***loading Fee $100.00*** " Cumberland Pelletizer, 24 knife rotor, bolt on knives, power roll feed, complete on base with variable speed drive, Serial No ***Loading Fee $100.00*** 143 Automatik strand pelletizer, model ASG 200, 200 mm wide helical rotor, power roll feed, driven by 20 hp, 460 volt motor with vfd controller.***loading Fee $100.00*** 144 Unused Kontro centrifugal pump, model CS2DCL, stainless steel construction, 3" x 2.5" x 5.5" impeller, with 10 hp, 3500 rpm, 230/460 volt motor, serial# Saturn dual shaft shredder, model 72-46HT, approximately 72" x 46" chamber, hydraulically driven with (3) 100 HP pumps, on stand with feed hopper, serial# 2246, built 1993.***Loading Fee $500.00*** 146 Process Control gravametric blender / feeder, model XBECYULLJE, 4 material with loaders and receivers, rated up to 650#/ hour, serial# A, new 1997.***Loading Fee $100.00*** 147 Process Control Corporation material push/pull vacuum pump with associated controls. 148 Leistritz twin screw extruder, model LSM 30.34, 34mm screws, counter rotating, electrically heated, air cooled, jacketed feed section, 38" long barrel, 7.5 KW motor on unitized base with control panel with 8 barrel zones and 1 die zone, serial# , new 1981.***Loading Fee $300.00*** cu ft Surge bin, carbon steel construction, approximately 72" diameter x 79" straight side x 32" deep cone bottom, flat top with 30", (3)6", 2", (5)1.5" top nozzles, 30" side access door, top mounted Mikro Pulsaire dust collector, model 12, carbon steel construction, with 113 sq ft filter area w...[more] cu ft Surge bin, carbon steel construction, approximately 66" diameter x 69" straight side x 92" deep cone bottom, flat top with 30", (2)2", (6)1.5" top nozzles, 30" side access door, 24" bottom outlet, top mounted Mikro Pulsaire dust collector, model 12, carbon steel construction, with 113 sq f...[more] 152 Mikro Pulsaire dust collector, model psi, carbon steel construction, with 216 sq ft filter area with (23) 8' long bags, vessel rated 22 psig at 100 f internal, pulse jet, serial# H18.***Loading Fee $100.00*** 153 cyclone, carbon steel construction, approximately 36" diameter x 74" straight side, 54" cone bottom.***loading Fee $100.00*** 154 FIX Peter Steimel GmBH super sack/gaylord loading station, type BIG-BAG/OKTABINBEFULLSTATION, designed to handle both super sack bags on skids and gaylord boxes on skids, up to 1600 kg, with loading head, scale and control panel, serial# 31020, built 1999***Loading Fee $100.00*** " Kason screen, model K60-2-CS, carbon steel construction, 1 deck design, on base wiht 1 hp, 230/460 volt motor, serial# KCN ***Loading Fee $100.00*** 156 Battenfeld planetary saw, model STU 250 E, range from 40mm to 250 mm diameter pipe, approximately 8" diameter blade, pipe clamps, with Battenfeld BMC controls with Lenz drives, 480 volt, serial# , new 2001***Loading Fee $300.00*** 157 Thyssen Krupp Nothelfer automatic solvent weld socketing machine, model KK 160 A/2, left side movement discharge, with PCS 095 Topline mini controls, serial# 115, new 2000.***Loading Fee $300.00***

9 " Welex Extruder, 24:1 L/D, electrically heated, air cooled, jacketed feed section, 9:38:1 gear box ratio, 100 H.P. gear box rating with 40 H.P. DC Motor, with 2.5" Berringer Hydraulic Screen Changer, Less hydraulic pump, Less temperature control panel, Less SCR.***Loading Fee $200.00*** 159 Gala 7 Pelletizer Cutting Head (parts only) 160 Cumberland granulator, model X1400, 1400 mm (56") wide x 600 mm (24") deep chamber, 5 knife open rotor, feed hopper, 150 hp motor, serial# , built 2000.***Loading Fee $500.00*** 161 Process Control gravametric blender / feeder, model XBECYULLJE, 4 material with loaders and receivers, rated up to 650#/ hour, serial# B, new 1997.***Loading Fee $100.00*** 162 Una Dyn Hopper Dryer with Heater and Blower, 200# Hopper with receiver. 163 OEM Sherbrook / Eagle Vision optical sorting line, model# S32/3/1.5/1.5, 32" wide with (3) Eagle Vision NIR vision systems, rated approximately 2000 kg/hour throughput, inline cascade design yielding four(4) material streams, 32" wide with associated conveyors and discharge chutes, Omron controls wi...[more] " Sherbrook belt conveyor, approximately 30" wide x 18' long belt, driven by.75 hp, 575 volt motor.***loading Fee $100.00*** 165 Gala spin dryer, model 5032BF, stainless steel product contact surfaces, 410 rpm, belt driven with 20 hp, 575 volt motor, gas fired heating system with gas train and burner, serial# ***Loading Fee $100.00*** 166 Cumberland Granulator, 14" x 16" feed opening, 3 knife open rotor, 2 bed knives, Gaylord High Discharge, with feed hopper, 20 H.P. 230/460 volt.***loading Fee $100.00*** " wide x 72" long Bunting cross belt magnet, cleated belt conveyor, driven by 2 hp, 230/460 volt motor, serial# Hydrovane rotary compressor, model 715-C08-200, rated approximately 75 cfm at 9 bar, 15 kw, 460 volt motor with integrally mounted air and oil cooler on base, serial# Tri-Clover centrifugal pump, model SP216M , stainless steel construction, 2" x 1.5" on base with 25 HP 460 volt 60 Hz motor, serial# P cu. ft. Paddle Mixer, stainless steel construction, jacketed shell, 8' L x 56" W x 54" D trough, 7 1/2 H.P. motor 3/60/220V, 6" end discharge, 30" discharge height.***loading Fee $200.00*** KW Regloplas temperature control unit, model 150KL83/4/TB21/2, 90L, 460 volt, serial# Lorik puller/cutter, model 90 H/2, 3" wide x 12" long belt puller with 1 HP motor, pneumatic adjustment, 3/4 HP cutter, 230 volt, serial# 90293A. 173 Process Control gravametric blender / feeder, carbon steel construction, 4 material with loaders and receivers, 115 volts***loading Fee $100.00*** 174 Una Dyn Hopper Dryer with Heat and Blower, 200# Hopper with receiver. 175 Brabender laboratory pelletizer, type , 2" wide brass rotor, (16) teeth, 115 volt, serial#

10 176 Leistritz twin screw extruder, model LSM 30.34, 34mm screws, 25:1 L/D, counter rotating, electrically heated, air cooled barrel, jacketed feed section, 850mm long vented barrel, with 19 KW 460 volt motor, on unitized base with control panel with 6 barrel and 1 die zones, serial# , new 19...[more] " Sterling Extruder, 30:1 L/D, electrically heated, water cooled, jacketed feed section, vented barrel, 150 HP DC motor with SCR controller, 11.39:1 gear box ratio, 8 zone control panel on base.***loading Fee $350.00*** 178 Toyota Dump N GoSealed Deep-Cycle 100 AH BatteriesStrobe Dash Mounted,Cap. Gauge,Pneumatic Tires,2-speed2000 lb rear suspension,horn, backup alarm, headlamp, brake lamphydraulic lift power pack and cylinder system,dc electric motormotor covermanual lift/lower controldump bin...[more] 179 Satake optical sorter, type Scan Master II, model SMII-8001EP, 8 lanes with camera's, stainless steel feed hopper with vibrating feeders, model 3010T Proface Xycom HMI, with Rittal air conditioner, Satake part# , serial# , built ***Loading Fee $250.00*** 180 Kongskilde pneumatic air aspirator, model KIA60, carbon steel construction, rated approximately 2250kg/hour through put, initegrally mounted blower with 20 hp blower, model MTD40, on stand, pack# , serial# ***Loading Fee $150.00*** mm Berstorff twin screw strand pelletizing line consisting of One (1) Techweigh volumetric feeder with motor drive, One (1) 40 mm Berstroff twin screw extruder, model ZE40A HT, electrically heated, water cooled barrel, 30:1 L/D, top vented, 50 hp dc drive with control panel with scr controller, O...[more] 182 Netzsch filter press, model 630-I/40/45, 630 mm (24") plates with (41) plates, (40) chambers, center fed, open delivery, sq ft surface area, 9.88 cu ft cake capacity, 25 mm cake thickness, overhead plate shifter with 3/4 hp XP motor drive, 230/460 volt w/ electric brake, dual acting hydraulic...[more] " Allgaier screen, model TSM 2000/3, stainless steel product contact surfaces, two decks with cover, on base, no motor, serial# 3675, built 1994.***Loading Fee $100.00*** 184 Battenfeld caterpiller dual belt puller saw combination, model DESC125R, 5" wide x 70" long contact dual belt puller section, with saw attachment, serial# ***Loading Fee $350.00*** 185 Holzmag single shaft shredder, model , approximately 50"" wide single shaft rotor, 12" diameter, driven 100 hp, 230/460 volt motor drive, with horizontal hydraulic ram with 5 hp, 230/460 volt pump, control panel with Allen Bradley SLC5/03 plc controller, spare screen and knives, serial# 31...[more] 186 Hytrol 24" W x 19' L Belt Conveyor, Motor HP: 2, Width: 24***Loading Fee $100.00*** 187 Tramrail vertical baler, with approximately 62" wide x 29" deep x 44" high bale section, on board 10 hp, 230/460 volt hydraulic pump, serial# 80E-64E.***Loading Fee $100.00*** 188 Mitts & Merril Hog Mill, Model 15 CSE, rear discharge, 20" X 27" feed opening, 30" diameter rotor, rated up to lbs/hour, presently equipped with 150 HP 440 Volt motor, can handle up to 250 HP motor, on base, Serial No. G ***Loading Fee $450.00*** 189 Gloucester Granulator, Model 1428-HD-100, heavy duty design, 14" x 28" feed opening, 3 knife open rotor, 2 bed knives, feed hopper with motorized lifting mechanism, belt driven with 100 H.P. motor, Serial No ***Loading Fee $450.00*** ' Flex-Weigh inclined cleated belt conveyor, model DWM-IV, 24" wide x 30' long rubber cleated belt, 4" high cleats, approximately 7' discharge height, serial# F ***Loading Fee $350.00***

11 191 Process Control gravametric blender / feeder, model EB476BF004, carbon steel construction, 4 material with loaders and receivers, 115 volts, serial# D, new 1994.***Loading Fee $100.00*** 192 Motan Diagnostic dryer, model MDD400, 21.6 KW total heater load, 8 hp total motor, 480 volt, wit (3) insulated hoppers with top mounted receivers, (2) auxiliary receivers with top mounted loaders, (1) filter, serial# ***Loading Fee $100.00*** 193 Used mini pelletizer, 0.25" width rotor, 32 teeth, driven by.5 hp DC motor, no controls /4" Randcastle Microtruder, 7" barrel, 28:1 l/d, electrically heated, (3) zone with (1) die zone, driven by 1/2 hp DC motor, with controls. 195 Process Control gravametric blender / feeder, model EB477BF004, carbon steel construction, 4 material with loaders and receivers, 115 volts, serial# B, new 1994.***Loading Fee $300.00*** 196 Una-Dyn hopper dryer system, model DHD-60, with heater and 10hp blower, controls on skid, with two (2) receivers, 460 volt, 3 phase, serial# DHD , Model/Type: DHD-60 ***Loading Fee $300.00*** 197 Killion pelletizer, model 5888, 2" wide rotor with approximately (20) diagonal teeth, driven by 1/2 hp motor, 180 volt, with bronco controls, serial# 5888., Motor HP:.5, Serial Number: 5888, Width: Puhl V-CAD 5 air separation / classifier system with approx 25' H bucket elevator with 15" W plastic bucket, air flow dampening separation technology classifing system including rotary valves, cyclone collector and 40 HP process blower, all steel construction.***loading Fee $600.00*** 199 2" Deltaplast cold feed extruder, 24:1 l/d, electrically heated, air cooled barrel, jacketed feed section, pedestal mounted with power roll strip feeder driven by.25 hp dc motor, 25 hp dc main drive with control panel and main drive SCR controller.***loading Fee $100.00*** 200 SSI 400 HP model 5000 HD twin shaft shredder, with (2) 200 HP, 460 Volt hydraulic power units, hydraulic ram with power unit.***loading Fee $900.00*** 201 3" Sussex Cross Head Die, 3 material design. 202 Process Control gravametric blender / feeder, model XBLHGGXX, carbon steel construction, 4 material with loaders and receivers, 120 volt, serial# , new 1994.***Loading Fee $100.00*** 203 Una Dyn Hopper Dryer with Heater and Blower, 200# hopper with receiver mm Leistritz twin screw extruder, 80mm parallel screws, counter rotating, 25:1 L/D, electrically heated, air cooled, jacketed feed section, vented barrel with vacuum pump, 71 KW 460 volt DC motor with SCR controller, slide plate screen changer, panel view PLC operator panel, rebuilt by Entek, seri...[more] " W x 30' L Inclined Belt Conveyor***Loading Fee $100.00*** 206 Condux granulator Model CS 800 / 2000 lll A, 800 mm x 2000 mm rotor, (12) knife open rotor, scissor cut, belt driven with 300 hp, 1190 RPM, 460 volt motor, feed hopper with hydraulic tilt cover and screen holder with hydraulic unit, on stand serial# 5570, built 1990.***Loading Fee $500.00*** 207 Una-Dyn vacuum loader, model #3, consisting of (1) Roots rotary lobe blower, designation 36 AF, driven by a 3 hp, motor, silencer included, mounted on frame, 480 volt, 3 phase, serial# L

12 208 Novatech hopper dryer, model PIII-400, with 2 hp blower and controls on frame, 460 volt, 3 phase, with carbon steel hopper, serial# ton Newberry injection molder, model H6-100MT, 14" x 17" tie bar spacing, hydraulically driven extruder, 20 hp on board pump, 460 volt, serial# MS-91, built 1991.***Loading Fee $400.00*** 210 winder, for 48" long rolls, driven by 0.5 DC motor, with controls and SCR on frame, with extra spindle.***loading Fee $100.00*** 211 Roach belt conveyor, approxmately 36" wide x 288" long smooth belt, with approximately 2 hp drive, serial# Lloyd Instruments twin column material tester, type 6000R, with grippers and 30Kn, (2)10Kn, (2)2500N, 100N, load cells, computer controls, serial# Rotex screener, model 764, carbon steel construction, 60" wide x 120" long screen area, 2 deck design, aluminum cover, on base with hp, volt motor, serial#.***loading Fee $300.00*** 214 Ball & Jewell shredder granulator unit, with model SB-15/515-A-11X dual shaft shredder, approximately 24" x 24" chamber, with 15 hp motor, serial# , model SG-2026-SCSX granulator, approximately 20" x 26" feed opening, with 40 hp motor, serial# ***Loading Fee $300.00*** 215 6" Beringer Hydraulic Screen Changer, slide gate style, dual breaker plates, on base with hydraulic power pack.***loading Fee $200.00*** 216 6" Cumberland Pelletizer, power roll feed, 3 H.P. 575 volt variable speed drive, on base, Serial# ***Loading Fee $100.00*** 218 KM Mutschink spin dryer, stainless steel construction, top mounted 3 kw, 480 volt motor.***loading Fee $100.00*** kw IMS water boiler, model WS-75D WATERSTAR, 250 F heating capacity, with 1 hp Goulds pump, size 1 1/4 x 1 1/2-6, 230 volts, 3 phase, serial# WS75SD Carver Laboratory press, model 2697, 12 ton capacity, 12" x 12" independently heated platens with controls,, maximum 10" opening, 5.2 kw heating capacity, 230 volt, manual hydraulic press, serial# " Embossing stand, 16" diameter x 102" wide chormed embossing roll, cored with rotary unit, 16" diameter x 102" long rubber bottom roll with stainless steel bottom pan, hydraulically operated top roll gap adjustment with 2 hp power pack, 12.6 kw dc bottom roll drive, misc spare embossing rolls.**...[more] " x 14' Z style metal cleated belt conveyor, approx. 28" wide x 8' long flat section x 3' inclined section x 3' flat section, approx. 40" discharge height, with 1 hp /460 volt motor.***loading Fee $150.00*** " traveling up-acting saw, 1/2 hp, with clamp, measured 15" of travel " HPM Extruder, 24:1 L/D, electrically heated, air cooled, 30 HP dc motor with scr controller, control panel with 3 barrel and 1 die zone, top vented with plug, serial # 88449***Loading Fee $400.00*** 225 Process Control gravametric blender / feeder, model EB477BF004, carbon steel construction, 4 material with loaders and receivers, 115 volt, serial# , new 1994.***Loading Fee $100.00***

13 226 Process Control gravametric blender / feeder, model EB477BF004, carbon steel construction, 4 material with loaders and receivers, 115 volt, serial# B, new 1994.***Loading Fee $100.00*** 227 Davis-Standard Gemini conical twin screw extruder, model GC8HD, 130/61 mm conical screws, counter rotating, electrically heated, air cooled barrel, jacketed feed section, 48" long vented barrel with vacuum pump, 17.4:1 gearbox ratio with 40 HP 460 volt AC motor with AC variable speed controller, on...[more] mm Maris pelletizing line consisting of the following, One (1) 92 mm Maris twin screw co rotating extruder, type TM92M, 30:1 l/d, electrically heated, water cooled barrel, with closed water circulation system with pump, heat exchanger and reservoir, (9) total barrel sections consisting of (1) fee...[more] 229 Satake optical sorter, type Scan Master II, model SMII-8401EP, 8 lanes with camera's, stainless steel feed hopper with vibrating feeders, model 3010T Proface Xycom HMI, with Rittal air conditioner, Satake serial# , built 2008.***Loading Fee $200.00*** " diameter tubular screw conveyor, galvanized construction, approximately 10" diameter x 12' long, chain drive with approximately 2 hp motor drive.***loading Fee $100.00*** 231 Cumberland Granulator, Model 24, 14" x 24" feed opening, 3 knife open rotor, 2 bed knives, feed hopper presently equipped with 50 H.P. 440 volt XP Motor will take up to 100 H.P., removable screen, on base, Serial No ***Loading Fee $150.00*** 232 Cincinnati Milacron PVC compouding line consisting of the following, One (1) Dosing feeder with variable speed control, One (1) Cincinnati Milacron twin screw conical extruder, model CM 55HP, 55 mm tapered screws, 40 hp dc motor, vented barrel with vacuum pump and unitized control panel, serial# [more] 234 8" diameter Egan Extruder model 8035 D-H, 32:1 L/D ratio, vented barrel, electrically heated, water cooled, 11.73:1 gearbox ratio, 600 HP DC drive with Safetronics SCR, Updated temperature control panel with 6 barrel zones and 1 die zone, Egan serial# C ***Loading Fee $800.00*** 235 Process Control gravametric blender / feeder, carbon steel construction, 4 material with loaders and receivers, 115 V***Loading Fee $100.00*** 236 Welding Engineers model HT 0.8 counter rotating twin screw extruder, 500 rpm, 10 HP, serial# 2741, year 1993.***Loading Fee $250.00*** 237 Roach belt conveyor, approxmately 36" wide x 244" long smooth belt, 2 hp, 230/460 volt drive, serial# ***Loading Fee $100.00*** " Midwestern Industries screener, model ME3006-6, carbon steel construction, single deck, on base with 1 hp, 230/460 volt motor drive, serial# " Egan Crammer Feeder, stainless steel construction, 43" diameter x 18" straight side x 33" cone bottom, 4.5" bottom outlet, bolt on top with 8" & 10" ports, 78" L x 88" W x 88" H overall dimensions, with 15 hp, DC motor, 22.5:1 gearbox ratio.***loading Fee $300.00**...[more] 240 Cumberland model 62B granulator, 2 bed knives, three knife open rotor, 200 HP 1185 RPM motor, with hopper, serial# ***Loading Fee $400.00*** 241 Process Control gravametric blender / feeder, model XBLHGGXX, carbon steel construction, 4 material with loaders and receivers, 120 volt, serial# , new 1994.***Loading Fee $100.00***

14 243 AEC Loader, single material with 48 cu. ft. hopper, carbon steel hopper and AEC AF-1 Additive Feeder with motor and bunting magnet. 244 Davis-Standard sheet stack with 66" wide x 18" diameter three roll vertical stack, cored rolls with rotary unions, 2 hp dc drive motor, pneumatically adjustable first and third rolls, temperature distribution system with heat exchangers, pumps and controls, 84" long cooling conveyor section, Advanz/...[more] 245 GEC blown film die, 6" diamter, rotating capability with 1/6 hp, 230/460 volt motor drive, heater bands, air ring on cart.***loading Fee $100.00*** 246 Air Conveyor Corp. paper shredding system with feed hopper, slot conveyor, 24" x 36" single rotor shredder driven by 30 hp motor, air separator with 40 hp blower, 8' x 8' x 9' pulse jet dust collector with blower with control panel.***loading Fee $500.00*** 247 Cumberland granulator, model 37, approximately 18" x 37" feed opening, 3 knife open rotor, with feed hopper, belt driven with 75 hp motor.***loading Fee $300.00*** MM OMV / Cincinnati Milacron single screw extruder, model EXD-120, approximately 34:1 L/D, electrically heated, water cooled barrel, jacketed feed section, 220 kw, 460 volt dc motor, control panel with scr motor controller, temperature control panel less Eurotherm controllers, set up for 8 barre...[more] 249 Process Control gravametric blender / feeder, model EB477BF004, carbon steel construction, 4 material with loaders and receivers, 115 volt, serial# C, new 1994.***Loading Fee $100.00*** 250 Cumberland granulator, model 20, approximately 20" wide feed opening, 5 knife closed rotor, direct coupled 100 hp, 1180 rpm, 220/440 volt motor on stand with feed hopper, serial# ***Loading Fee $200.00*** 251 6" BERLYN HYDRAULIC SCREEN CHANGER***Loading Fee $100.00*** 252 Davis-Standard Extruder, 3.5", 32:1 L/D, electrically heated, air cooled with blowers, Model 350SAD7767, 106 H.P. gear box rating with 1.5 service factor 17.39:1 gear ratio, V-Belt Drive, peviously operated with 100 H.P. motor, standard center line, on base, less motor and less control panel.***load...[more] 253 6" Sterling extruder, 32:1 L/D, electrically heated, water cooled barrel with circulation system, jacketed feed section, 68" center line height, 400 hp dc motor with scr controller, 17.5:1 gear box ratio, 100 rpm screw speed, control panel designed for 6 barrel, 3 screen changer, 2 adaptor, 1 melt p...[more] 254 Sterling extruder, 3.5" diameter screw, 30:1 L/D, 100 HP motor, 13.95:1 gearbox ratio, Sterling serial# with Kreyenborg hydraulic screen changer with hydraulic pump, with Process Controls Corp 4-compartment blender/feeder system with associated controls.***loading Fee $400.00*** 255 Davis-Standard Mark V extruder, model 3.5 MV350, 100mm diameter 26:1 barrel, no screw, electrically heated, air cooled, five barrel zones, four die zones, 17.41:1 gearbox ratio rated 158HP max with 1.25 service factor, with 60HP 460V AC 1780 RPM motor with Allen- Bradley VFD, serial# I3134, SO# [more] 256 Process Control gravametric blender / feeder, carbon steel construction, 4 material with loaders and receivers, 115 V***Loading Fee $100.00*** MM Davis-Standard Extruder, electrically heated, water cooled, 30:1 L/D, vented barrel, 17.26:1 gearbox ratio, 100 H.P. DC Motor, skid mounted with controls and SCR, Serial No. L2025, SO #03201, New 1990.***Loading Fee $500.00***

15 " Davis-Standard Mark V Extruder, Model DS2.5MS, 24:1 L/D, electrically heated, air cooled, jacketed feed section, 17.4:1 gearbox ratio, 40 HP DC motor, 4 barrel, 1 die zones, unit is skid mounted with control panel and SCR controller, Serial No. J-8532, SO# 98675, New 1985.***Loading Fee $ [more] " NRM Davis Standard extruder, 24:1 L/D, electrically heated, water cooled, jacketed feed section, 24.89:1 gearbox ratio, 100 HP DC motor with SCR, control panel with 4 barrel, 5 die zones with temperature controllers, water circulation system with pump, serial# 19364, SO# 64696, new 1999.***Load...[more] 260 Century II AZ-15 Shredder, approximately 12.5" wide x 27.5" long chamber, 20 hp, 230/460 volt, on stand with feed hopper, serial# , built 1985***Loading Fee $200.00*** 261 6" Sterling extruder, 32:1 L/D, electrically heated, water cooled barrel with circulation system, jacketed feed section, 68" center line height, 400 hp dc motor with scr controller, :1 gear box ratio, 100 rpm screw speed, control panel designed for 6 barrel, 3 screen changer, 2 adaptor, 1 melt...[more] 262 6" APV Sterling Davis-Standard extruder, 32:1 L/D, electrically heated, water cooled barrel with circulation system, jacketed feed section, 68" center line height, 400 hp dc motor with scr controller, :1 gear box ratio, 100 rpm screw speed, control panel designed for 6 barrel, 3 screen changer...[more] 263 6" Berlyn Hydraulic Screen Changer, slide gate design, (2) 6" braker plates, less hydraulic power pack.***loading Fee $100.00*** 264 Davis-Standard Thermatic extruder, model 25IN25, 2.5" diameter screw, 30:1 L/D, 6 heating zones, 50 HP motor, 17.2:1 gearbox ratio, Davis Standard serial# P3177, with hydraulic screen changer, with Process Controls Corp. 4-compartment blender/feeder model EB476DF004 controls.***loading Fee $400.00**...[more] 265 Davis-Standard Thermatic extruder, model 25IN25, 2.5" diameter screw, 30:1 L/D, 6 heating zones, 50 HP motor, 17.2:1 gearbox ratio, Davis Standard serial# AG293, with Kreyenborg hydraulic screen changer, with Process Controls Corp. 4-compartment blender/feeder model EB476DF004 with controls.***load...[more] 266 Ball & Jewel granulator, model HDS 3652, approximately 36" deep x 52" wide feed opening, staggered 5 knife open rotor driven by dual 100 hp, 460 volt motors, feed hopper, serial# ***Loading Fee $500.00*** MM OMV / Cincinnati Milacron single screw extruder, model EXD-120, approximately 34:1 L/D, electrically heated, water cooled barrel, jacketed feed section, 220 kw, 460 volt dc motor, control panel with scr motor controller, temperature control panel less Eurotherm controllers, set up for 8 barre...[more] 268 Davis-Standard Mark V extruder, model 35MV350, 100mm diameter, 26:1 L/D barrel, no screw, electrically heated, air cooled with five barrel zones and four die zones, 17.4:1 gearbox ratio, 158 max HP with 1.25 service factor, with 60HP 460V AC 1750 RPM motor with Allen-Bradley VFD, serial# I6468, SO#...[more] 269 Nelmore granulator, approximately 18" x 36" feed throat, staggered rotor, feed hopper with manual screw tilt, jacketed chamber, belt driven with 50 hp 575 volt motor on base.***loading Fee $200.00*** 270 2" Killion single screw extruder, 24:1 L/D, electrically heated, air cooled barrel, jacketed feed throat, 25 hp dc motor with SCR, thru Koellmann gear box with 9.457:1 ratio, control panel with (3) barrel zones and (4) die zones, on stand with transformer and control panel, 480 volt, 3 phase, Killio...[more] " Davis Sterling extruder, 30:1 L/D, electrically heated, air cooled, 5 barrel zones, 50 HP DC motor with SCR, with Una-Dyn hopper dryer/ loader system model 200#, extruder serial# R2529, year 1995.***Loading Fee $250.00***

16 273 Davis-Standard Thermatic extruder, model 20IN20, 2" diameter screw, 30:1 L/D, 25 HP motor, 17.56:1 gearbox ratio, Davis Standard serial# U2544, with Kreyenborg hydraulic screen changer, with Process Controls Corp. 4-compartment blender/feeder model EB476DF004 with controls.***loading Fee $250.00*** 274 2" Royal Extruder, 35:1 L/D, model 268, electrically heated, water cooled, 4 barrel zones, 6 die zones, with 30 hp motor with VFD controller, 460V, 3 phase, job # 8001, serial # , built 10/2002***Loading Fee $250.00*** 275 Davis-Standard Mark V extruder, model MV-35INDS, 100MM diameter 26:1 L/D barrel, no screw, electrically heated air cooled with five barrel zones and four die zones, 17.03:1 gearbox ratio, 125HP max with 1.25 service factor, with 75HP DC motor with Reliance SCR, serial# 05582, SO# 65482, Year 1999.**...[more] " Egan extruder, 24:1 l/d, electrically heated, water cooled barrel, closed loop water system with reservior, 50 hp dc motor, on board control panel with 7 barber coleman 520 temperature controllers.***loading Fee $400.00*** " extruder, 30:1 L/D, Flender gearbox, electrically heated, air cooled barrel, no screw, four barrel zones, two die zones, 10 HP 575V AC 1745 RPM motor.***loading Fee $250.00*** " HPM Extruder, 30:1 L/D, electrically heated, water cooled, crammer feeder with variable speed drive, 220 RPM max. screw speed, vented, 40 H.P. D.C. Variable Speed Drive with SCR Controller, with Lufkin Gear Box, serial# 94404, built 1995***Loading Fee $300.00*** ton Filtrine chiller, model PCP-300WE-40L, water cooled with 3 hp compressor, r22 refrigerant, 480 volt, serial # 4002/94.