Safety Switches. c o n t e n t s SPEEDFAX TM 2017

Transcription

1 Safety Switches SPEEDFAX TM 2017 Section General Duty Switch Heavy Duty Switch Window Switch c o n t e n t s Safety Switch Guide Form Specifications -2 Feature Comparison -3 Enclosure Types - ing System -5 General Duty Safety Switches Plug Fuse Enclosed Type, 120/20V Fusible Selection -6 60A Special Application Type, 20V Non-Fusible Selection -6 General Duty Switches Features -7 20V Fusible and Non-Fusible Selection -8 Heavy Duty Safety Switches Heavy Duty Switches Features -9 20V Fusible Selection V Fusible Selection V Non-Fusible Selection -12 Type /X and 12 with Viewing Window Selection -13 Special Applications Safety Switches -Pole and 6-Pole Selection -1 Interlocked Receptacle Selection -15 Non-Metallic and 316 Grade Stainless Selection -16 Enclosed Solar PV Disconnects -17 Accessories General and Heavy Duty Switches Class R Fuse Clips -18 Class J Fusing -18 Class T Fuse Adapter Kits -18 Neutral Kits % Neutral Kits -18 Fuse Puller Kits -18 Auxiliary Contacts -19 Copper Lug Kits -19 Equipment Ground Kits -19 Isolated Ground Kits -19 Interchangeable Hubs -20 Compression Lug, Neutral Barrier Kits -20 Lugs and Wire Ranges -20 Multiple Padlocks -20 Kirk-Key Interlocks -20 Dimensions and Weights General and Heavy Duty Switches Type 1 and 3R Knockout Diagrams Non-Metallic and Receptacle Switch Dimensions -27 -Pole and 6-Pole Switch Dimensions -28 Double-Throw Switches Selection Dimensions -31 Enclosed Rotary Disconnect Switches VBII Safety Switch Replacement Parts -3 SAFETY Scan to connect online to the most up-todate version of this Section of SPEEDFAX. Siemens Industry, Inc. SPEEDFAX 2017 Product -1

2 Type VBII Safety Switches Guide Form Specifications Product Overview SAFETY Application Short Circuit Withstand s General Duty Heavy Duty Double Throw General Duty Switches are intended for applications where reliable performance and continuity of service are needed, but where duty requirements are not severe and usual service conditions prevail. (These switches are intended for use primarily with supply circuits rated 20V AC or less where the available fault current is less than 100,000A when used with Class R or T fuses or 10,000A max. when used with Class H fuses.) Suitable for use on systems capable of delivering not more than 100,000 RMS symmetrical amperes of fault current as follows: Sw. AIC Protective Device a A 10,000 Circuit Breaker A 10,000 Class H Fuse A 100,000 Class R Fuse A 100,000 Class J or T Fuse Heavy Duty Switches are intended for use in applications where: 1. Rugged construction, reliable performance, continuity of service and ease of maintenance are emphasized, or 2. Available fault currents higher than 10,000A are likely to be encountered, such as in manufacturing plants, mass production industries, and commercial, institution-al and other large buildings served by network systems or transformers of higher capacities. 3. System voltage is 600V AC or DC Max.. A Type 12 or / X enclosure is required. Double throw switches are intended to transfer loads from one power source to another. All 2 & 3 pole double throw switches are suitable for use as service equipment. All are UL Listed. Switches are rated for use on systems with an available fault current of up to 10,000 AIC when protected with Class H fuses or either 100,000 or 200,000 AIC when protected with Class R, J or Class T fuses. They can also be used to connect a single source of power to either of two loads, In this application it is necessary to field modify fusible switches so that the fuses are on the load side of the switching mechanism. Suitable for use on systems capable of delivering not more than 200,000 RMS symmetrical amperes of fault current as follows: Sw. & Tpye AIC Protective Device a All Heavy Duty & DT 10,000 Circuit Breaker A HD & DT 10,000 Class H Fuse 60A Compact HD 100,000 Class R, J or T Fuse GD & P DT 100,000 Class R, J or T Fuse A HD 200,000 Class R, J or T Fuse A DTF & DTNF DT b 200,000 Class R, J or T Fuse 800 & 1200A HD & DT b 200,000 Class L or T Fuse Fuses Fusible switches will accept the following UL class fuses: 30 LF - 30A max plug Fuses A GF Class H & K, Class R with kit A GF Class J-move base GF Class T with kit A GF Class T-move bases Fusible switches will accept the following UL class fuses: A HF Class H & K, Class R with kit A, 600V HF Class J-move base A, 20V HF Class J-move base A HF Class T with kit A HF Class T-move bases A HF Class L, Class T with kit c Fusible switches will accept the following UL class fuses: A DT & F Class H & K, Class R with kit 30 & 60A 600V DT Class J-move base A DT Class J-move base, Class T with kit A DT Class J-standard, Class T-move bases 00A 20v F Class H-standard 00A, 600V & 600A F Class T-Standard Cover Interlocks Underwriters Laboratories, Inc. NEMA Specifications Seismic Qualifications Groundable Neutral (All neutrals are bondable for service entrance use.) Voidable cover interlocks on switches prevent the switch door from being opened when in the ON position. No cover interlock on 30A Type 3R or on plug fuse type switches. Listed by UL under file #E776 as enclosed switches and also suitable for use as service equipment (where applicable). UL98 Enclosed and Deadfront Switches. Meet NEMA standard KS for type GD switches. Voidable dual cover interlocks standard on all heavy duty switches. Prevents cover from being opened when switch is in the ON position and prevents switch from being turned ON when door is opened. Meet NEMA standard KS for type HD switches. All GD & HD switches and DT type double throw switches have been tested and comply with the 2010 California Building Code (CBC) and with the 2009 International Building Code (IBC) - Compliance Level SDS = 1.85 g Fusible switches have groundable neutral blocks factory installed. Non-fusible switches accept field addable neutrals. All switches (both Fusible and Non-Fusible) are either supplied with factory installed neutrals or accept field addable neutrals. Dual cover interlocks standard on all double throw switches. Prevents cover from being opened when switch is in the ON position and prevents switch from being turned ON when door is opened. Meet NEMA standard KS type GD for DTG & type HD for DT, F & NF switches. All except pole switches will accept field addable neutrals except that DTG 100 & 200A switches are also available with factory installed neutrals. Padlocks Padlockable cover latch. OFF padlock provisions on handle. Padlockable cover latch and multiple OFF padlock provisions on handle. Padlockable cover latch and multiple OFF padlock provisions on handle. HP & Load Break s All General Duty, Heavy Duty and Double Throw Switches are both load break and horsepower rated. a The protective device can either be a fuse installed in a fusible switch or an upstream fuse or circuit breaker protecting a non-fusible switch. The ampere rating of the upstream protective device must not exceed the switch ampere rating. b All pole and fusible double switches with catalog numbers starting with F are rated 100,000 AIC max. c Class T kit available for 20V max. applications on 1200A switches. -2 Siemens Industry, Inc. SPEEDFAX 2017 Product

3 Feature Comparison Product Overview General Heavy Double Features / Duty Duty Throw s b b b 30 thru 600 Amps b b 800 and 1200 Amps b b b 20 Volt AC b b 600 Volt AC b b b 250 Volt DC b 600 Volt DC b b b Double-break visible blade design (30-200A) b b b Quick-make, quick-break switching action b b b Highly visible ON/OFF handle indication b Handle design for hook stick operation b b b Padlockable cover latch b b b Padlockable handle b c b Single voidable cover interlock b b Dual voidable cover interlock b b b Type 1 enclosure b b b Type 3R enclosure b b Type 12 enclosure b b Type / X enclosures b b b Generous wiring gutters that meet UL and NEC wire-bending space requirements b b b Lugs suitable for copper or aluminum at 60 or 75 C b b b CU/AL wire lugs that meet UL 86B requirements b b Suitable for field-convertible compression connectors b f b b All plated copper current carrying parts (except lugs) b b b Spring reinforced Fuse Clips (except 30A general duty) b b b Clear pivoting line terminal shield b b b Replacement parts b Field addable 200% neutral b g b ag bag Provisions for UL Class T, R and H Fuses b ba Provisions for UL Class J and L Fuses b b Metal nameplate A b b Aux. switch kits b d Type X with stainless steel interior parts b e b Rolled flange enclosure design (30-200A) b b Isolated ground kits on in operation off Double Break Switching Action Like the time-proven Vacu-Break Design, the Siemens VBII double break switching action breaks the arc in two places in A ratings. This reduces heat generation and increases switching speed by doubling the breaking distance. The result is enhanced performance and increased longevity. We also provide the most visible blade design available today. Unlike conventional knife blade switches, the blades are self-aligning to ensure positive contact. In addition, they have no wear and friction point since the electrical hinge has been eliminated. The result is a very fast, positive and reliable switching action for even the most severe applications. SAFETY a 00, 600V & 600A fusible, double-throw switches accept only Class J or T fuses. Only 800 & 1200A HD switches will accept Class L fuses. b 30A general duty switches have fuse clips constructed of spring type copper. c Not supplied on 30A outdoor & plug fuse switches. d A Type VBII in stainless steel enclosures. e A. f 200A general duty switches have aluminum neutral assemblies. g A GD & DT and A HD switches will accept Class T fuses. Siemens Industry, Inc. SPEEDFAX 2017 Product -3

4 Safety Switches General Duty and Heavy Duty Product Overview SAFETY Enclosure Types h A Type 1 enclosures are intended for indoor use primarily to provide protection against contact with the enclosed equipment in locations where unusual service conditions do not exist. h B Type 3R enclosures are intended for outdoor use primarily to provide a degree of protection against falling rain and sleet and must remain undamaged by the formation of ice on the enclosure. They are not intended to provide protection against conditions such as dust, internal condensation, or internal icing. h C Type, X enclosures are intended for indoor or outdoor use primarily to provide a degree of protection against windblown dust, rain, splashing water and hose-directed water. They are not intended to provide protection against conditions such as internal condensation or internal icing. Also meets X definition by providing a high degree of protection against corrosion. Siemens A stainless steel X switches are supplied stainless interior parts and hardware as standard. h D Type enclosures are intended for indoor or outdoor use primarily to provide a degree of protection against windblown dust, rain, splashing water and hose-directed water. They are not intended to provide protection against conditions such as internal condensation or internal icing. h E Type 12 a enclosures are intended for indoor use primarily to provide a degree of protection against dust, falling dirt and dripping water. They are not intended to provide protection against conditions such as internal condensation. Type 7/9 enclosures for use in hazardous locations. Use with molded case switches listed in Section 7. h A hb Load Break s All Siemens safety switches are load break rated. The load break rating is assigned by UL after the switching unit has successfully performed the following tests: of Switch ON/OFF of Operations Operations With Without per Minute Current Current Total Horsepower s All Siemens safety switches, where appropriate, are horsepower rated. s are approved by UL only after the switching unit has undergone testing to determine its acceptability which includes repeated interruption of the locked rotor current of the motor for which it is to be rated as follows: Max HP of ON/OFF of Cycles Operations per minute of Operation h C hd Non- Fusible Safety Switch AIC s When Protected by a Circuit Breaker Breaker Frame Non-Fused Switch UL Listed Short Circuit Current NEG, NGB, ED 30 DT (20V) 18 ka Thru 20 VAC NEB, NEG, NGG, A GD & DT (20V) 18 ka Thru 20 VAC NGB, ED NEB, NEG, NGG, A HD & DT (600V) 18 ka Thru 80 VAC NGB, ED ED A HD & DT (600V) 18 ka Thru 600 VAC FD6-A, JD6-A 200A HD & DT (600V) 18 KA Thru 600 VAC JD6-A, LD6-A 00A GD & DT (20V) 18 ka Thru 20 VAC JD6-A, LD6-A 00A HD & DT (600V) 18 ka Thru 600 VAC LD6-A 600A GD & DT (20V) 25kA Thru 20 VAC LD6-A 600A HD & DT (600V) 25kA Thru 600 VAC NNG 1200A HD & DT (600V) 25 ka Thru 600 VAC VBII Type 12 switches are also rated 3R & 3S for outdoor use. Type 3R is defined in B above. 3S rated enclosures provide a degree of protection against windblown dust and allow operation when the enclosure is ice laden. All switches above are rated at 10 KA when protected by any UL Listed CB Circuit breaker trip rating must not exceed switch ampere rating h E - Siemens Industry, Inc. SPEEDFAX 2017 Product

5 ing System Type VBII Safety Switch ing System Product Overview H F 3 6 N R CU A Switch Type L = General Duty 10k AIC Max. (Plug Fused & 60A Max Non-Fused) G = Gen. Duty H = Heavy Duty DT = Double Throw DTG = General Duty DT Fused or Non-Fused F = Fused NF = Non-Fused of Poles 1 = 1 2 = 2 3 = 3 Voltage = 6 = 6 1 = 120V or 120/20V 2 = 20V 6 = 600V s 1 = 30A 2 = 60A 3 = 100A = 200A 5 = 00A 6 = 600A 7 = 800A 8 = 1200A Series Type A = 00A, 600A Omit = 30A-200A, 800A-1200A Special Applications With: CH = Crouse-Hinds Receptacle CJ = Factory J Fuse Spacings CR = Class R Clips Installed CU = Factory-Installed Copper Lugs G = Factory-Installed Ground Bar H = Height or Size Reduced L = Oversized Enclosure PN = Pyle-National Receptacle PV = Photovoltaic rated PVPG = Photovoltaic rated, Positive Ground W = Viewing Window Enclosure Type Omit = Type 1, Indoor R = Type 3R, Outdoor S = Type / X, Stainless Steel SS = Type / X, 316 Grade Stainless Steel X = Type / X, Non-Metallic J = Type 12, Industrial XL = Type /X Non-Metallic Less Line & Load Lugs With or Without Neutral Omit = Less Neutral N = With Neutral SAFETY Type VBII Accessories ing System H R 6 A Switch Type H = Heavy Duty G = General Duty Series Type A = 00A, 600A Omit = 30A-200A, 800A-1200A Accessory Type A1 = Auxiliary Switch 1/NO and 1/NC A2 = Auxiliary Switch 2/NO and 2/NC A3 = Auxiliary Switch Low Current CL = Compression Lug Barrier / Mounting Kit CU = Copper Lug G = Ground Lug Kit G2 = Insulated Ground Lug Kit J = Class J Fuse Kit LC = Copper Lug Kit N = Neutral N2 = 200% Neutral NCM = Field Replacement Lug Kit P = Fuse Puller Kit R = Class R - Fuse Clip Kit T = Class T - Fuse Kit s 1 = 30A 2 = 60A 12 = 30/60A 3 = 100A 23 = 60/100A 123 = 30/60/100A Maximum Voltage 2 = 20V Max 6 = 600V Max 123 = 30/60/100/200A = 200A 5 = 00A 56 = 00/600A 5678 = 00/600/800/1200A 6 = 600A 78 = 800/1200A Note: numbering systems above do not apply to -pole & Type F & FR double throw switches & accessories. For 00A, 600A use 680V max accessories except for T Fuse Kit. Only offered for 00A, 600A. For 30A-200A, 800A-1200A. Siemens Industry, Inc. SPEEDFAX 2017 Product -5

6 General Duty Enclosed Switches Plug Fuse and 60A Special Application Type Selection Features e b Compact size b Horsepower rated b Indoor and outdoor enclosures b Quick make-quick break mechanism b Visible ON - OFF indications b Padlock-off handle feature b Door padlock provision b Bondable neutral (where indicated) b Lugs suitable for copper or aluminum wire b UL Listed b Fuses not included b Switches accept Edison base plug fuses b Hubs see page -20 b Lugs see page -20 SAFETY Dimensions (inches) Type Height Width Depth R Wire Range Table Switch Type Wire Range 120/20 Volt Fusible Cu/Al 30 Amp #1 to #8 AWG d 120/20 Volt Non-Fusible Cu/Al 60 Amp #1 to #3 AWG Indoor Type 1 Outdoor Type 3R a Horsepower s Ship. Wt. (lbs.) Ship Wt. (lbs.) 1-Phase, 2-Wire Pkg. of 10 Pkg. of 10 Standard Maximum 120/20 Volt Fusible 1-Pole and Solid Neutral b 120 Volt 1-Phase, 2-Wire 30 LF111N 35 LF111NR Pole and No Neutral 120/20 Volt 1-Phase, 2-Wire 30 Use 2-Pole and Solid Neutral 2-Pole and Solid Neutral b 120/20 Volt 1-Phase, 3-Wire 30 LF211N 35 LF211NR Volt Non-Fusible 2-Pole Special Application Switch 1 or 2-Pole No Fuse 20 Volt 1-Phase, 2-Wire 60 LNF222R c For inches / millimeters conversion, multiply inches by 25.. a Dual horsepower ratings: Std. applies when non-time delay plug fuses are installed. Max applies when time-delay plug fuses are installed. b Has service entrance label. UL Listed as Enclosed Switches (suitable for use as service equipment where indicated) under File #E776. (NEMA) Type G.D. Federal Spec. W-S-865C type LD or type NDS c Bottom cable entry and exit only. No hub provision supplied. GSGK60 is included and factory installed. d Line lugs will accept and are UL approved for #1 to #6 Cu/Al cable. e Features also apply to 2- and 3-pole, 30A general duty switches on page Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category GDSS

7 General Duty Safety Switches Features (60-600A) Product Overview SAFETY Cover interlock 2. Tangential knockouts through 600A for easy conduit lineup 3. Quick-make, quick-break operating mechanism that ensures positive operation. Provisions for T, R, J, H, and K class fuses (T & J A) 5. Generous wiring gutters that meet or exceed NEC wire-bending space requirements 6. Visible blade, double-break switch action 7. Positive 2 or 3 point mounting 8. Highly visible red handle grip 9. Informative door labeling which includes replacement parts list 10. Handle and cover padlocking provisions 11. Side-hinged door that opens 180 degrees for easier wiring 12. A unique enclosure design that adds rigidity and strength. Its rolled edge prevents cuts and scrapes to conductors and to installer s hands Siemens Industry, Inc. SPEEDFAX 2017 Product -7

8 General Duty Safety Switches Selection SAFETY System 20 Volt Fusible Indoor Type 1 2-Pole, 2-Fuse, and Solid Neutral bcd Ship Wt. (lbs.) Std. Pkg Outdoor Type 3R Ship Wt. (lbs.) Std. Pkg Horsepower a 20V AC Phase, 2-Phase, 3-Phase, Volt 2-Wire -Wire 3-Wire DC Std. Max. Std. Max. Std. Max. Std. 20 Volt AC/250 Volt DC 030 GF221N 035 g GF221NR e 35 g GF222N 01 GF222NR GF223N 023 GF223NR GF22N 07 GF22NR Pole, 3-Fuse, and Solid Neutral d 20 Volt AC/250 Volt DC 030 GF321N 2 f GF321NR e 02 f GF322N 15 GF322NR GF323N 25 GF323NR GF32N 9 GF32NR GF325NA 9.6 GF325NRA GF326NA 95.6 GF326NRA Volt Non-Fusible cd 2-Pole or 3-Pole 20 Volt AC/250 Volt DC 030 GNF f GNF321R e 02 f GNF GNF322R GNF GNF323R GNF32 06 GNF32R GNF325A 11 Use 600V Switch HNF365RA GNF326A 116 Use 600V Switch HNF366RA a Dual horsepower ratings: Std.- applies when non-time delay fuses are installed. Max.- applies when timedelay fuses are installed. b These switches are UL-listed for application on grounded B-phase systems. c Suitable for use on 3-phase motor loads. d Service entrance labeled. e Has provision for ECHA type hub. f 5 switches per standard package. g 10 switches per standard package. h Height reduced switch (5.25 rather than 56 inches in height) for use with 500MCM or smaller conductors. -8 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category GDSS

9 Heavy Duty Safety Switches Features SAFETY Quick-make, quick-break operating mechanism that ensures positive operation. 2. Visible blade, double-break switching action. 3. Arc chutes dissipate heat and prolong switch life.. Highly visible red handle grip. Designed for hook stick operation. 12. Unique enclosure design increases rigidity and prevents cuts and scrapes to conductors and installer s hands. 13. Spring reinforced fuse clips that assure reliable contact for cool operation. 1. Door latch securely holds door closed and allows cover padlocking Defeatable dual cover interlock. 6. Center punch provided for field drilling to allow ON padlocking. 7. Handle can be padlocked in the OFF position with up to (3) padlocks with 5/16" hasps. 8. Generous top, bottom and side gutters that meet or exceed NEC wire-bending space requirements. 9. Informative door labeling which includes replacement parts list. 10. Tangential knockouts through 600A for easy conduit lineup. 11. Side-hinged door that opens past 180 degrees for easier wiring. 15. Front removable mechanical lugs that are suitable for CU/AI 60 or 75 C conductors. 16. Lugs are field convertible to copper body and to a wide variety of compression connectors. 17. Hinged clear line terminal shield with probe holes for inspecting or testing line side terminals. 18. Embossed aluminum nameplate on Heavy Duty Switches provides highly visible ON/OFF indication. 19. Drawn cover for increased rigidity and resistance to abuse. 20. Top key hole and bottom mounting holes provide easy 2 or 3 point mounting. Siemens Industry, Inc. SPEEDFAX 2017 Product -9

10 Heavy Duty Safety Switches Selection SAFETY System Indoor Type 1 Ship Wt. (lbs.) Std. Pkg Outdoor Type 3R Ship Wt. (lbs.) Std. Pkg Horsepower a 20V AC 1-Phase, 2-Wire 2-Phase, -Wire 3-Phase, 3-Wire 250 Volt DC Std. Max. Std. Max. Std. Max. Std. 20 Volt Fusible e 2-Pole, 2-Fuse, and Solid Neutral c (Also used for 2-Pole, 2-Wire Applications) 20 Volt AC/250 Volt DC 30 HF221N 012 HF221NR HF222N 018 HF222NR HF223N 023 HF223NR HF22N 07 HF22NR HF225NA 91.1 HF225NRA HF226NA 95.6 HF226NRA HF227N 365 HF227NR HF228Nn 385 HF228NRn Pole, 3-Fuse, and Solid Neutral (Also used for 3-Pole, 3-Wire Applications) 20 Volt AC/250 Volt DC 20 Volt Fusible e 2-Pole, 2-Fuse d 3-Pole, 3-Fuse d 0030 HF321N 01 HF321NR HF322N 019 HF322NR HF323N 025 HF323NR HF32N 09 HF32NR HF325NA 9.6 HF325NRA HF326NA 99.6 HF326NRA HF327N 375 HF327NR HF328N 395 HF328NR Volt AC/250 Volt DC Type /X Stainless Type 12 Industrial f 0030 HF221S 013 HF221J HF222S 019 HF222J HF223S 02 HF223J HF22S 08 HF22J (Also used for 2-Pole, 2-Wire Applications in A s) 20 Volt AC/250 Volt DC 0030 HF321S 01 HF321J HF322S 020 HF322J HF323S 025 HF323J HF32S 09 HF32J HF325SA 93 HF325JA HF325SSA HF326SA 98 HF326JA HF326SSA HF327S 370 HF327J n Built to order. Allow 3-5 weeks for delivery. Height reduced switch (5.25 rather than 56 inches in height) for use with 500MCM or smaller conductors. Dual horsepower ratings: Std.- applies when non-time delay fuses are installed. Max.- applies when timedelay fuses are installed. These switches are UL-listed for application on grounded B-phase systems and are suitable for 3-phase motor applications. When a neutral is required use a field installed neutral kit. Suitable for use as service entrance equipment. Also rated Type 3S/3R. 30 grade stainless steel. For switches with enclosures constructed from 316 grade stainless steel, see page Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

11 Heavy Duty Safety Switches Selection System 600 Volt Fusible e 2-Pole, 2-Fuse c 3-Pole, 3-Fuse Indoor Type 1 Ship Wt. (lbs.) Std. Pkg Outdoor Type 3R Ship Wt. (lbs.) Std. Pkg Horsepower 80V AC 1-Phase, 3-Phase, 2-Wire 3-Wire 600V AC 1-Phase, 2-Wire 3-Phase, 3-Wire Std. Max. Std. Max. Std. Max. Std. Max. 250 Volt DC 600 Volt DC 80 Volt AC/600 Volt AC/600 Volt DC 0030 HF HF261R HF HF262R HF HF263R Volt AC/600 Volt AC/250 Volt DC a 0030 HF361 1 HF361R HF361L g 19 HF361RL g HF HF362R HF362RL HF363 2 HF363R HF36 8 HF36R HF365A 93 HF365RA HF366A 98 HF366RA HF HF367R HF HF368R Pole, 3-Fuse and Solid Neutral 80 Volt AC/600 Volt AC/250 Volt DC a 0030 HF361N 01 HF361NR HF362N 019 HF362NR HF363N 025 HF363NR HF36N 09 HF36NR HF365NA 9.6 HF365NRA HF366NA 99.6 HF366NRA HF367N 375 HF367NR HF368N 395 HF368NR Volt Fusible e (For 2-Pole Applications use outside poles of 3-Pole Switches) 2-Pole, 2-Fuse c 80 Volt AC/600 Volt AC/600 Volt DC Type /X Stainless Type 12 Industrial f 0030 HF261S 015 HF261J HF262S 020 HF262Jn HF263Sn 027 HF263Jn SAFETY 3-Pole, 3-Fuse n Built to order. Allow 3-5 weeks for delivery. a A 3-Pole switches are also rated 600V DC. b Height reduced switch (5.25 rather than 56 inches in height) for use with 500MCM or smaller conductors. c Use 3-Pole switch for 200A applications. Product Category HDSS d Dual horsepower ratings: Std.- applies when non-time delay fuses are installed. Max.- applies when timedelay fuses are installed. e Suitable for use as service entrance equipment except on 1200 Amp solidly grounded wye systems per NEC f Also rated Type 3S/3R. 80 Volt AC/600 Volt AC/250 Volt DC a 0030 HF361S 013 HF361J HF362S 020 HF362J h 0100 HF363S 025 HF363J h 0200 HF36S 09 HF36J HF365SA 93 HF365JA HF365SSA HF366SA 98 HF366JA HF366SSA HF367S 370 HF367Jn HF368Sn 388 HF368Jn g Indicates oversized enclosure (30A switch with 60A lugs in a 60A enclosure or 60A switch with 100A lugs in a 100A enclosure). h 600V DC & 600V DC horsepower rating shown requires (2) poles to be connected in series. 30 grade stainless steel. For switches with enclosures constructed from 316 grade stainless steel, see page -16. Siemens Industry, Inc. SPEEDFAX 2017 Product -11

12 Heavy Duty Safety Switches Selection Indoor Type 1 Outdoor Type 3R Horsepower Ship Wt. (lbs.) Ship Wt. (lbs.) 20 Volt 1-Phase 3-Phase 80 Volt 1-Phase 3-Phase 600 Volt 1-Phase 3-Phase System 250V DC 600V DC SAFETY 600 Volt Non-Fusible d 2-Pole 80 Volt AC / 600 Volt AC / 600 Volt DC 30 HNF HNF261R HNF HNF262R HNF263 2 HNF263R Pole 80 Volt AC / 600 Volt AC / 250 Volt DC 30 HNF HNF361R HNF361RL f HNF362H b 11 HNF362RH b HNF362 a 18 HNF362R a g 60 HNF362RL f g 100 HNF363 a 23 HNF363R a g 200 HNF36 a 6 HNF36R a HNF365A a 75 HNF365RA a HNF366A a 77 HNF366RA a HNF HNF367R HNF HNF368R Volt Non-Fusible d 2-Pole c 80 Volt AC / 600 Volt AC / 600 Volt DC Type / X Stainless Type 12 Industrial 30 HNF261S 13 HNF261J HNF262S 20 HNF262J HNF263Sn 25 HNF263Jn Pole 80 Volt AC / 600 Volt AC / 250 Volt DC 30 HNF361S 13 HNF361J HNF362SH b 15 HNF362JH b HNF362S a 19 HNF362J a g 100 HNF363S a 2 HNF363J a g 200 HNF36S a 7 HNF36J a HNF365SA a 75 HNF365JA a HNF365SSA HNF366SA a 77 HNF366JA a HNF366SSA HNF367S 295 HNF367Jn HNF368Sn 310 HNF368Jn n Built to order. Allow 3-5 weeks for delivery. a A 3-Pole switches are also rated 600V DC. b Compact switch (11.1"H, 6.6"W box less cover and handle). Short circuit withstand rating 100,000 RMS sym. amps. c Use 3-Pole switch for 200A application. d Suitable for use as service entrance equipment except for 1200 when used on a 80 or 600V grounded wye system. e Also rated type 3S / 3R. f Indicates oversized enclosure (30A switch in a 60A enclosure or a 60A switch in a 100A enclosure. g 600V DC and 600V DC horsepower rating shown requires (2) poles to be connected in series. 30 grade stainless steel. For switches with enclosures constructed from 316 grade stainless steel, see page Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

13 Heavy Duty Safety Switches Type /X & 12 with Viewing Window Selection Description A, 3-pole 600V max. in fusible and non-fusible versions in Type /X stainless steel and Type 12 enclosures. All allow viewing of visible blade position A also allow viewing of indicating type fuses. Features b Rugged installer-friendly enclosure design features a gasket flange with continuously welded seams b Tool-free cover latches b Two, three and four point mounting b Metal handle with large insulating grip features a positive stop in both ON and OFF position b Ground lugs provided as standard b Type 12 enclosures are fabricated from galvanized steel and are also rated for 3R/3S outdoor applications b Type X stainless steel switches (30 200A) are provided with stainless steel interior parts b The widest range of accessories available including 200% neutrals, gold plated PLC auxiliary contacts and isolated ground kits System Ship Wt. (lbs.) Maximum Horsepower 20V AC 80V AC 600V AC 1-Phase, 2-Wire 3-Phase, 3-Wire 3-Phase, 3-Wire 3-Phase, 3-Wire 3-Pole, 3-Wire Fusible, Type 3R 600 Volt AC / 250 Volt DC 30 HF361RW HF362RW V DC 600V DC SAFETY 3-Pole, 3-Wire Non-Fusible, Type 3R 600 Volt AC / 250 Volt DC 30 HNF361RW HNF362RW Pole, 3-Wire Fusible, Type Volt AC / 250 Volt DC 30 HF361JW HF362JW HF363JW HF36JW HF365JWA HF366JWA Pole, 3-Wire Non-Fusible, Type Volt AC / 250 Volt DC 30 HNF361JW HNF362JW HNF363JW HNF36JW HNF365JWA Pole, 3-Wire Fusible, Type X Stainless Steel 600 Volt AC / 250 Volt DC 30 HF361SW HF362SW HF363SW HF36SW HF365SWA HF365SSWA Pole, 3-Wire Non-Fusible, Type X Stainless Steel 600 Volt AC / 250 Volt DC 30 HNF361SW HNF362SW HNF363SW HNF36SW HNF365SWA HNF365SSWA a 200A switches are also rated 600V DC. Maximum HP ratings listed apply only when time delay fuses are used. Also rated 3S/3R for outdoor use. All switches are suitable for use as service entrance equipment. Use outside poles of 3-pole switch for 2-pole application. 600V DC and 600V DC horsepower rating shown requires (2) poles to be connected in series. 30 grade stainless steel. For switches with enclosures constructed from 316 grade stainless steel, see page -16. Product Category HDSS Siemens Industry, Inc. SPEEDFAX 2017 Product -13

14 Heavy Duty Safety Switches Type VBII & 6-Pole Heavy Duty Safety Switches Selection SAFETY Application & 6-pole Switches are commonly used as a disconnecting means for two-speed, two-winding motors. Fused switches provide both over current and short circuit protection. Non-fusible switches normally provide a local disconnection means for twospeed motors which are remote from their motor controller. -pole switches are also used in 3-phase, -wire circuits when a switching neutral is required. All & 6-pole switches are service entrance rated. Description & 6-pole switches are available in A ratings and in both fusible and non-fusible versions. -pole switches are supplied with either Type 1 or Type12/3R enclosures. 6-pole switches are available with either Type 12/3R or Type X stainless steel enclosures. Standards b UL & CUL listed under file #E776 b Meets UL98 for enclosed switches b & 6-Pole switches are suitable for use as service entrance b Meets NEMA Standard KS-1 for enclosed switches b Meets NEC wire bending space requirements Features b Visible blade, double break switching action b Highly visible ON/OFF indication b Defeatable dual cover interlock b Padlock option in OFF position b All copper current carrying parts a b Tangenital knockouts (Type 1, -pole switches) HNF662J -Pole Type VBII Switches ab Indoor Type 1 Type 12/3R Industrial Horsepower s Amp Ship Wt. Ship Wt. 20V, 2Ø, W 20V 3Ø 80V, 3Ø 600V, 3Ø 250V System (lbs.) (lbs.) DC Std. Max. Std. Max. Std. Max. Std. Max. Fusible 600 Volt AC, 250 Volt DC -Pole, Fuse d 30 HF61 36 HF61J HF62 0 HF62J HF63 3 HF63J HF6n 88 HF6Jn Non-fusible 600 Volt AC, 250 Volt DC -Pole 30 HNF61 32 HNF61J HNF62 3 HNF62J HNF63n 36 HNF63Jn HNF6n 78 HNF6Jn Pole Type VBII Switches abe Type 12/3R Industrial Type X Stainless Steel Horsepower s c Amp Ship Wt. Ship Wt. 20V 3Ø 80V, 3Ø 600V, 3Ø 250V System (lbs.) (lbs.) Std. Max. Std. Max. Std. Max. DC Fusible 600 Volt AC, 250 Volt DC 6-Pole, 6 Fuse d 30 HF661J 37 HF661Sn HF662J 1 HF662Sn HF663Jn HF663Sn HF66Jn 90 HF66Sn Non-fusible 600 Volt AC, 250 Volt DC 6-Pole 30 HNF661J 33 HNF661S HNF662J 35 HNF662S HNF663J 37 HNF663S HNF66J 80 HNF66Sn n Built to order. Allow 3-5 weeks for delivery. a Lugs are aluminum alloy as standard. Optional copper body lugs are available. b All & 6-pole VBII switches are suitable for use as service equipment when a neutral is installed or equipment ground kit is properly connected. c Dual horsepower ratings: Std. applies when non-time-delay fuses are installed. Max. applies when time delay fuses are installed. d Fusible switches accept Class H Fuses as the standard. Class R & J fuses can also be installed and increase the rating from 10,000 to 200,000 AIC. For Class J, the load base is moved upward. For Class R fuses, rejection kits are required. e Supplied with factory installed ground lugs. -1 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

15 Heavy Duty Safety Switches Special Application Switches / Interlocked Receptacle Switches Selection Application Receptacle Safety Switches provide cord connection protection of heavy-duty portable equipment (welders, infrared ovens, batch feeders, portable conveyors, assembly line fixtures and tools, refrigerator trucks, etc.) under load or fault conditions. Standards All receptacle switches are UL listed under file #E776. Those with a viewing window are also CSA certified under file # Description ab Type 12 and /X Receptacle Safety Switches are available with 3-phase, -wire grounded type Crouse-Hinds Arkite 2 or Pyle-National receptacle, pre-wired and mounted with interlock linkage to the switch mechanism. Insertion or removal of the plug is prevented by the interlock linkage while the switch is in the ON position. Receptacle prevents operation of switch if incorrect plug is inserted. Crouse-Hinds Interlocked Receptacle Switches Type 12 Type /X Shipping Accepts Crouse-Hinds Wt. (lbs.) Arktite a Plug Std. Pkg. HF362JCH SAFETY 20V Fusible, 3-Pole, 3-Wire 30 HF321JCH HF321SCHs 23 APJ385 & NPJ HF322JCH HF322SCHs 30 APJ685 & NPJ HF323JCH HF323SCHs 36 APJ1087 & NPJ V Fusible, 3-Pole, 3-Wire 30 HF361JCH HF361SCH 2 APJ385 & NPJ HF362JCH HF362SCH 30 APJ685 & NPJ HF363JCH HF363SCHs 36 APJ1087 & NPJ V Non-Fusible, 3-Pole, 3-Wire 30 HNF361JCHs HNF361SCHs 22 APJ385 & NPJ HNF362JCH HNF362SCH 29 APJ685 & NPJ HNF363JCHs HNF363SCHs 35 APJ1087 & NPJ V Fusible, 3-Pole, 3-Wire with Viewing Window 30 HF361JCHWs HF361SCHWs 2 APJ385 & NPJ HF362JCHW HF362SCHW 30 APJ685 & NPJ HF363JCHWs HF363SCHWs 36 APJ1087 & NPJ V Non-Fusible, 3-Pole, 3-Wire with Viewing Window 30 HNF361JCHWs HNF361SCHWs 22 APJ385 & NPJ HNF362JCHW HNF362SCHWs 29 APJ685 & NPJ HNF363JCHWs HNF363SCHWs 35 APJ1087 & NPJ1087 Pyle-National Interlocked Receptacle Switches 3-Poles Fusible and Non-Fusible Type 12 Type 12 Stainless Steel Shipping Accepts Pyle-National Voltage Wt. (lbs.) QuelArc bc Plugs Switch Receptacle Std. Pkg. Plug (F) HF361JPNs HF361SPNs (N-F) HNF361JPN HNF361SPN 21 JPD (F) HF322JPNs (F) HF362JPNs HF362SPNs 28 JPD (N-F) HNF362JPN HNF362SPN 27 s Built to order. Allow 6 8 weeks for delivery. a Arktite is a registered trademark of the Crouse- Hinds Company. Plugs are not sold or supplied by Siemens. Product Category HDSS b Indicates plug with maximum diameter cable bushing. c QuelArc is a registered trademark of the Pyle- National Company. rating of both switch and receptacle. Also rated Type 3R/3S. Enclosure is constructed of Type 30 stainless steel. Siemens Industry, Inc. SPEEDFAX 2017 Product -15

16 Heavy Duty Safety Switches Special Application Safety Switches / Type VBII Non-Metallic & 316 Grade Stainless Steel Application Siemens Non-metallic and 316 grade stainless steel switches provide a superior level of corrosion resistance to assure trouble free performance in the most severe conditions. 316 grade stainless steel provides increased corrosion resistance when compared to 30 grade, especially in atmospheres containing a high level of chlorine commonly encountered in marine and waste management applications. Our non-metallic enclosures are constructed from fiberglass reinforced polyester and are extremely resistant to a wide range of corrosive atmospheres. They allow a wide range of operating temperatures and their insulating properties virtually eliminate problems caused by internal condensation. Description A, 600V Max, fusible and nonfusible switches are available in both non-metallic and 316 grade stainless steel versions. All are supplied with factory installed ground bars as standard. Viewing windows are also available in the stainless offering. SAFETY Type /X Non-Metallic Ship Weight Std. pkg. (lbs.) Horsepower 3-Phase 20 Volt AC 80 Volt AC 600 Volt AC Std. Max. Std. Max. Std. Max. 250 Volts DC 600 Volts DC 3-Pole, -Wire, 20 Volt Fusible, Type X e 30 HF321NX HF322NXs Pole, -Wire, 600 Volt AC Fusible, Type X bce 30 HF361NX d 60 HF362NX d 100 HF363NXs a d 200 HF36NXs a Pole, 3-Wire, 600 AC Volt Non-Fusible, a Type X bc 30 HNF361X d 60 HNF362X d 100 HNF363Xs d 200 HNF36Xs Type /X 316 Grade Stainless Steel Standard With Viewing Window Ship Weight (lbs.) Horsepower 3-Phase 20 Volt AC 80 Volt AC 600 Volt AC Std. Max. Std. Max. Std. Max. 250 Volts DC 600 Volts DC 20V AC, 250V DC Fusible 3-Pole, 3-Wire 30 HF321SSs HF322SSs HF323SSs HF32SSs V AC, 250V DC Fusible 3-Pole, 3-Wire c 30 HF361SS HF361SSW HF362SS HF362SSW d 100 HF363SS HF363SSWs d 200 HF36SS HF36SSWs V AC, 250 V DC Non-Fusible 3-Pole, 3-Wire ac 30 HNF361SS HNF361SSW HNF362SS HNF362SSWs d 100 HNF363SS HNF363SSWs d 200 HNF36SS HNF36SSWs s Built to order. Allow 6 8 weeks for delivery. a Also used for 20 volt applications. b Add L to end of catalog number for switches less line & load lugs with mounting hardware for crimp type or copper body lugs. c 200A switches are also rated 600V DC max. d 600V DC voltage and horsepower rating shown requires (2) poles to be connected in series. e Supplied with factory installed neutral. -16 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

17 Heavy Duty Safety Switches Enclosed Solar Photovoltaic (PV) Switches Selection Application Solar disconnect switches are designed to be used in the DC portion of photovoltaic power generation circuits. They incorporate powerful magnets within the switch line base which work in combination with a double break switching action to quickly dissipate the very hot arc that is generated when a 600V DC circuit is opened under load. These circuits are defined by article 690 of the NEC which requires the grounded conductor to be at ground potential at all times and therefore cannot be switched. Description A switches are available in both Type 1 and 3R enclosures and in both fusible and non fusible versions. They are provided with an additional door mounted warning label as required by the NEC and are supplied with a factory installed equipment ground bar. They are built to UL98 requirements but are UL listed in file number E as UL171 photovoltaic disconnect switches. They are 3 pole switches that are approved to switch 3 separate 600V DC circuits (one per pole). The design incorporates many of the standard VBII switch features including a rolled out enclosure front flange, a large metal operating handle, oversized line and load lugs and large wire gutters. 1000VDC photovoltaic switches are UL98B listed for solar applications and comply with article 690 of the NEC. The new Amp switches are also UL98B listed at 600VDC and come in NEMA Type 3R. Solar Photovoltaic Enclosed Disconnect Switches Indoor Type 1 Outdoor Type 3R Rated Isc Ship Wt* Std. Pkg. Ship Wt* Std. Pkg. Per NEC Article 690 Negative Ground 3 Pole 3 Wire Fusible 600Volt DC 30 HF361PV 1 HF361RPV A 60 HF362PV 20 HF362RPV A 100 HF363PV 25 HF363RPV A 200 HF36PV 9 HF36RPV A Negative Ground 3 Pole 3 Wire Non-Fusible 600Volt DC 30 HNF361PV 12 HNF361RPV A 60 HNF362PV 19 HNF362RPV A 100 HNF363PV 2 HNF363RPV A 200 HNF36PV 7 HNF36RPV A NEW Positive and Negative Ground, 1 Pole, Fusible 1000 Volt DC 200 HF110NPV 52 HF110NRPV A NEW Positive and Negative Ground, 1 Pole, Non-Fusible 1000 Volt DC 200 HNF110NPV 50 HNF110NRPV A Positive Ground 3 Pole 3 Wire Fusible 600Volt DC 30 HF361PVPG 1 HF361RPVPG A 60 HF362PVPG 20 HF362RPVPG A 100 HF363PVPG 25 HF363RPVPG A 200 HF36PVPG 9 HF36RPVPG A Positive Ground 3 Pole 3 Wire Non-Fusible 600Volt DC 30 HNF361PVPG 12 HNF361RPVPG A 60 HNF362PVPG 19 HNF362RPVPG A 100 HNF363PVPG 2 HNF363RPVPG A 200 HNF36PVPG 7 HNF36RPVPG A NEW Positive and Negative Ground, 2 Wire, 600Volt DC, Type 3R Amperage No. Poles Fuse Type s Built to order. Allow 6 8 weeks for delivery. * In pounds (lbs) Ship Wt* Std. Pkg 00A 1 Fusible HF165NRPV A 00A 1 Non-fusible HNF165NRPV A 00A 2 Fusible HF265NRPV A 00A 2 Non-fusible HNF265NRPV A 600A 1 Fusible HF166NRPV A 600A 1 Non-fusible HNF166NRPV A 600A 2 Fusible HF266NRPV A 600A 2 Non-fusible HNF266NRPV A Rated Isc Per NEC Article 690 Note: All disconnects are rated at 10,000 AIC per UL requirements when used with or protected by Class K, J or R fuses rated at 600VDC. HF361PV HNF361RPV HF362RPV SAFETY Product Category HDSS Siemens Industry, Inc. SPEEDFAX 2017 Product -17

18 General and Heavy Duty Safety Switches Accessories Selection HR612 HT63 HN26 SAFETY Class R Fuse Clip Kits All General Duty and Heavy Duty Switches are field convertible to accept Class R Fuse Clip Kits. The kits prevent the installation of Class H and K fuses (one kit required per 3-pole switch). Class R Fuse Clip Kits GSRK321 HR21 HR612 HR62 HR63 HR6 HR65A HR66A Class J Fusing All A, 600V and A,20V fusible Heavy Duty Switches are field convertible to accept Class J fuses by moving the load base to a pre-drilled J fuse position. All A, 20V fusible General Duty switches can also be field converted to accept Class J fuses. Class J Fuse Kits HJ66A Internal Shield Kits (for fusible switches) Kits provide a clear plastic inner door to prevent accidental contact with live parts. Test probe holes are provided and fuses can be replaced without removal of kit. NEW Internal Shield Kits b Switch 30A HD 60A HD 100A HD 200A HD Description 30A, 20V Kit (GD only) 30A, 20V Kit (HD only) 30A, 600V Kit/60A, 20V Kit 60A, 600V Kit 100A Kit 200A Kit 00A Kit 600A Kit Description 600A, 20V/600V Kit Kit HSK61SSW HSK62SSW HSK63SSW HSK6SSW Class T Fuse Adapter Kits All A, General Duty and Amp and 1200Amp Heavy Duty Switches are field convertible to accept Class T fuses.800a switches are field convertible to accept Class T fuses by moving the load base to a pre-drilled T fuse position. Class T Fuse Adapter Kits a HT23 HT63 HT2 HT6s HT25A HT65A HT26A HT66A TFAK82 HN612 Description 100A, 20V Kit 100A, 600V Kit 200A, 20V Kit 200A, 600V Kit 00A, 20V Kit 00A, 600V Kit 600A, 20V Kit 600A, 600V Kit 1200A, 20V Kit Neutral Kits Standard Neutral Kits can be field installed in General and Heavy Duty Switches. Neutral Kits Switch Kit 30 GD W HD, 60 GD HN612 60, 100 HD, 100 GD HN HN6 00 & 600 HN656A 800 & 1200 HN % Neutral Kits UL listed 200% Neutrals are available on A Heavy Duty Switches. They are typically used with non-linear transformers or where increased neutral ampacity/lug capacity is required. 200% Neutral Kits Switch HP61 Kit Fuse Puller Kits Fuse Puller Kits are field installable in A Type VBII Heavy Duty Switches (one kit required per 3-pole switch). Fuse Puller Kits Wire Range Line & Load Lugs (Cu/Al) 100 HN263 (2) #1-1/0 AWG 200 HN26 (2) #6 AWG-300 Kcmil 00 HN656A (2) 1/0 AWG-600 Kcmil (2) #6 AWG-300 Kcmil 600 HN678A (2) 1/0 AWG-600 Kcmil (2) #6 AWG-300 Kcmil Switch Fuse Puller Kit 030 HP HP62s 100 HP63s s Built to order. Allow 6 8 weeks for delivery. a One kit per pole required. b Not designed for use in Non-metallic X safety switches. Not designed for use with Auxiliary Contacts. -18 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

19 General and Heavy Duty Safety Switches Accessories Selection HA26123 HA26123 HLC612 HG26123 Auxiliary Contacts Auxiliary Contacts are available only for Heavy Duty Switches. The auxiliary contacts are available in 1 normally open and 1 normally closed or 2 normally open and 2 normally closed configurations. Siemens offers a PLC Auxiliary Switch (30-200A) that has very low resistance for low voltage and current typical in PLC circuits. All auxiliary contacts make after and break before main switch contacts. Auxiliary Contacts Switch Aux. Switch Kit 125V AC Max. Copper Lug Kits Heavy duty switches are UL approved to accept field installed copper lug kits. s Built to order. Allow 6 8 weeks for delivery. n Purchase field replacement kit along with lugs. 250V AC Max. 28V DC Max. Horsepower 125V AC Max. 250V AC Max. With 1 NO & 1 NC Isolated Contacts HA /2 3/ HA /2 3/ With 2 NO & 2 NC Isolated Contacts HA /2 3/ HA /2 3/ Low Current PLC Type with 1 NO & 1 NC Gold Plated Contacts HA /2 3/ HA /2 3/ Copper Lug Kits Switch Copper Lug Description HLC612 (9) Lugs/Kit #1- AWG Cu 100 HLC63s (9) Lugs/Kit #1-1/0 AWG Cu 200 HLC6s (9) Lugs/Kit #6 AWG-300 Kcmil Cu HCU656An (1) Lugs/Kit #1/0 AWG-600 Kcmil Cu HLC65678 (1) Lugs/Kit #1/0 AWG-600 Kcmil Cu NEW Quick Connects They provide two point control power take-off capability and are normally used on two poles on the line side when it is required to have control power available when the switch is in the OFF position. They provide a mounting provision for standard ¼ quick connect terminal. Installed in the line or load side. 30A VBII switches have lugs UL listed to accept (2) wires per pole as standard so a 30A kit is not required. Quick Connects HCQ62 HCQ63 HCQ6 Isolated Ground Kits Isolated Ground Kits are available on A Heavy Duty Switches. They are normally used on circuits with a high content of computer or other electronic loading which require a ground which is isolated from the building ground and neutral circuits. The kit includes both isolated and grounded terminals as listed below. Isolated Ground Kits Switch of Terminals Isolated Grounded HG #1- AWG HG2656A Equipment Ground Kits Switch Description 60A 2 wire quick connect kit 100A 2 wire quick connect kit 200A 2 wire quick connect kit of Terminals Wire Range Per Terminal (Cu/Al) 2/0-1 AWG 2/0-6 AWG Equipment Ground Kits Equipment Ground Lug Kits are available for all General and Heavy Duty Switches. They are field installable in Type 1 and Type 3R Switches and are factory installed as standard in Type / X and Type 12 and also in all VBII &6-pole Switches. Wire Range Per Terminal (Cu/Al) 30A GD GSGK60 2 #1-8 AWG GD HG #1- AWG HD HG #1- AWG 00 & 600 HG656A 2/0-6 AWG HG678 8 #6 AWG-250 Kcmil SAFETY Product Category HDSS Siemens Industry, Inc. SPEEDFAX 2017 Product -19

20 General and Heavy Duty Safety Switches Hub and Lug Data Selection SAFETY Interchangeable Hubs Conduit hubs are available for Type 3R, 12 and / X applications A Type 3R Switches are provided with a conduit hub provision and a removable hub plate on their top rainshed. Conduit Size (inches) Type 3R a Cover ECHA000 3/ ECHA075 1 ECHA / ECHA125 Cover ECHS000 3/ ECHS075 1 ECHS / ECHS /2 ECHS150 2 ECHS /2 ECHS /2 ECHV250 3 ECHV /2 ECHV350 ECHV00 Type /X b 3/ SSH075 1 SSH / SSH /2 SSH150 2 SSH /2 SSH250 3 SSH /2 SSH350 SSH00 Used On 30A GD Only A GD A HD A A A Note: 30 thru 200A. Type 3R Switches have removable hub plates on rainshed. 00A and larger Type 3R Switches have no provisions for mounting hubs. Drill or punch hole in the field to accommodate hub size desired. Field Replacement Kits and Neutral Barrier Kits All Heavy Duty Switches are field convertible for (Crimp) type lugs. When compression lugs are required for A switches, a neutral barrier kit is required for 1-Phase, 3W or 3-Phase, W applications. When compression lugs are required on A switches, lug mounting kits are required. Field Replacement Kits and Neutral Barrier Kits Switch Kit Description 30 HCL612 Neutral Barrier Kit 60 & 100 HCL623 Neutral Barrier Kit 00 HCM65A 20V/600V Fusible Kit 00 HNCM65A 20/600V Non- Fusible Kit 600 HCM66A 20V/600V Fusible Kit 600 HNCM66A 20V/600V Non- Fusible Kit 800 & 1200 e HCL65678n 1 Pole, Compression Lug Mounting Kit Lugs 30 & 60A Switches are suitable for use with 60 or 75 C wire A are suitable for use with 75 C rated wire. Multiple Padlock Accessory A tamper-proof device to provide for multiple padlocking to meet OSHA or plant requirements. Accepts up to 6 1/ padlocks. number SL020. Standard Carton-12. SSH125 ECHV300 ECHS200 Wire Ranges (Line, Load and Standard Neutral) Switch Wire Range with Wire Bending Space Per NEC Requirements Lug Wire Range 30GD #1-8 AWG (Cu/AI) f #1-6 AWG (Cu/Al) 30HD #1-6 AWG (Cu/AI) #1-2 AWG (Cu/Al) 60 hj #1-3 AWG (Cu/AI) #1-2 AWG (Cu/Al) 100 k #1-1/0 AWG (Cu/Al) #1-1/0 AWG (Cu/Al) 200 i #6 AWG-250 Kcmil (Cu/Al) #6 AWG-300 Kcmil (Cu/Al) 00 g (1) 1/0 AWG-600 Kcmil (Cu/Al) (2) 1/0 AWG-500 Kcmil (Cu/Al) (2) 1/0 AWG-600 Kcmil (Cu/Al) 600 g (1) 1/0 AWG-600 Kcmil (Cu/Al) (2) 1/0 AWG-500 Kcmil (Cu/Al) (2) 1/0 AWG-600 Kcmil (Cu/Al) (3) 1/0 AWG-750 Kcmil (Cu/Al) Line Load () 1/0 AWG-750 Kcmil (Cu/Al) neutral () 3/0 AWG-750 Kcmil (Cu/Al) Line Load () 1/0 AWG-750 Kcmil (Cu/Al) neutral (3) 1/0 AWG-750 Kcmil (Cu/Al) Line Load () 1/0 AWG-750 Kcmil (Cu/Al) neutral () 1/0 AWG-750 Kcmil (Cu/Al) Line Load () 1/0 AWG-750 Kcmil (Cu/Al) neutral SL020 n Built to order. Allow 3- weeks for delivery. a Hubs suitable for 3R Switches. b Also suitable for Type 12 applications. c Neutral Barrier kits are required on A switches only and only with 1-Phase / 3W or 3-Phase / W loads. Compression Lugs mounting kits are required on A switches only. d Provides mounting for a single line or load lug. e Provides mounting for (2) compression lugs per phase on line or load. f Line base lugs (only) are UL approved to accept #1-6 CU/Al cable. g Max. wire size for height reduced switches is 500 kcmil (Cu/Al). h All but 60A GD & Compact HD NF switches are also UL approved for #2 Cu/Al conductors. i All 200A Heavy Duty Switches have a wire range & wire bending space for (1) #6-300 Kcmil (Cu/Al). j Also for 30A oversized heavy duty switches. k Also for 60A oversized heavy duty switches. -20 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS & RESI

21 General and Heavy Duty Safety Switches Dimensions Safety Switch Dimensions (Inches)* & Shipping Weights Height Width Depth Box A With Door B With Rain Shed C Box D With Handle E Box F With Handle G Knockout Diagram Shipping Weight (lbs.) GF221N S1 35 (10) GF221NR S3 35 (10) GF222N S6 1 GF222NR S8 1 GF223N S10 23 GF223NR S11 2 GF22N S12 7 GF22NR S13 8 GF225NA S GF225NRA S GF226NA S GF226NRA S GF321N S2 2 (5) GF321NR S 2 (5) GF322N S6 15 GF322NR S8 15 GF323N S10 25 GF323NR S11 25 GF32N S12 9 GF32NR S13 50 GF325NA S GF325NRA S GF326NRA S GF326NA S GF326NRA S GNF S2 2 (5) GNF321R S 2 (5) GNF S7 12 GNF322R S9 13 GNF S10 23 GNF323R S11 2 GNF S12 6 GNF32R S13 7 GNF325A S18 75 GNF326A S18 77 HF221J also HF261J HF221N also HF S6 12 HF221NR also HF261R S8 13 HF221S also HF261S HF222J also HF262J HF222N also HF S16 18 HF222NR also HF262R S17 19 HF222S also HF262S HF223J also HF263J HF223N also HF S10 23 HF223NR also HF263R S11 2 SAFETY * For inches / millimeters conversion, multiply inches by 25.. a Knocks not provided on Type / X and 12 or in 800 & 1200A switches. Siemens Industry, Inc. SPEEDFAX 2017 Product -21

22 General and Heavy Duty Safety Switches Dimensions Safety Switch Dimensions (Inches)* & Shipping Weights SAFETY Height Width Depth Box A With Door B With Rain Shed C Box D With Handle E Box F With Handle G Knockout Diagram Shipping Weight (lbs.) HF223S also HF263S HF22J HF22N S12 7 HF22NR S13 8 HF22S HF225NRA S HF225NA S HF226NA S HF226NRA S HF227N HF227NR HF228N HF228NR HF365A S18 93 HF365JA HF365RA S19 93 HF365SA HF365SSA HF366A S18 98 HF366JA HF366RA S19 98 HF366SA HF366SSA HF321J HF321N S6 1 HF321NR S8 15 HF321S, SS HF322J HF322N S16 19 HF322NR S17 20 HF322S, SS HF323J HF323N S10 25 HF323NR S11 26 HF323S, SS HF32J HF32N S12 9 HF32NR S13 50 HF32S, SS HF325JA HF325NA S HF325NRA S HF325SA HF325SSA HF326JA HF326NA S HF326NRA S HF326SA HF326SSA HF327J HF327N HF327NR HF327S HF328N HF328NR HF361, PV, PVPG S6 1 HF361J, JW HF361L S16 19 HF361N S6 1 HF361NR S8 15 HF361R, RPV, RPVPG S8 15 HF361RL, RW S17 20 HF361S, SS, SSW, SW HF362, PV, PVPG S16 19 * For inches / millimeters conversion, multiply inches by 25.. a Knocks not provided on Type / X and 12 or in 800 & 1200A switches. -22 Siemens Industry, Inc. SPEEDFAX 2017 Product

23 General and Heavy Duty Safety Switches Dimensions Safety Switch Dimensions (Inches)* & Shipping Weights Height Width Depth Box A With Door B With Rain Shed C Box D With Handle E Box F With Handle G Knockout Diagram Shipping Weight (lbs.) HF362J, JW HF362N S16 19 HF362NR S17 20 HF362R, RPV, RPVPG, RW S17 20 HF362RL S11 25 HF362S, SS, SSW, SW HF363, PV, PVPG S10 2 HF363J, JW HF363N S10 25 HF363NR S11 26 HF363R, RPV, RPVPG S11 25 HF363S, SS, SSW, SW HF36, PV, PVPG S12 8 HF36J, JW HF36N S12 9 HF36NR S13 8 HF36R, RPV, RPVPG S13 9 HF36S, SS, SSW, SW HF365A S18 93 HF365JA, HF365JWA HF365NA S HF365NRA S HF365RA S19 93 HF365SA, HF365SWA HF365SSA, HF365SSWA HF366A S18 98 HF366JA, HF366JWA HF366NA S HF366NRA S HF366RA S19 98 HF366SA HF366SSA HF HF367J HF367N HF367NR HF367R HF367S HF368, J, S HF368N HF368NR HF368R HNF365JA HNF365RA S19 75 HNF365SA HNF365SSA HNF366SA HNF366SSA HNF366JA HNF366RA S19 77 HNF361, PV, PVPG also HNF261 & HNF362H S7 12 HNF361J, JW also HNF261J & HNF362JH HNF361R, RPV, RPVPG also HNF261R & HNF362RH S9 13 HNF361RL S17 20 HNF361S, SS, SSW, SW also HNF261S & HNF362SH HNF362, PV, PVPG also HNF S16 18 HNF362J, JW also HNF262J HNF362R, RPV, RPVPG also HNF262R S17 19 HNF362RL S11 2 HNF362S, SS, SSW, SW also HNF262S HNF363, PV, PVPG also HNF S10 23 HNF363J, JW also HNF263J HNF363R, RPV, RPVPG also HNF263R S11 2 HNF363S, SS, SSW, SW also HNF263S SAFETY * For inches / millimeters conversion, multiply inches by 25.. a Knocks not provided on Type / X and 12 or in 800 & 1200A switches. Siemens Industry, Inc. SPEEDFAX 2017 Product -23

24 General and Heavy Duty Safety Switches Dimensions Safety Switch Dimensions (Inches)* & Shipping Weights SAFETY Height Width Depth Box A With Door B With Rain Shed C Box D With Handle E Box F With Handle G Knockout Diagram Shipping Weight (lbs.) HNF36, PV, PVPG S12 6 HNF36J, JW HNF36R, RPV, RPVPG S13 7 HNF36S, SS, SSW, SW HNF365JA HNF365JWA HNF365RA S19 75 HNF365SA, HNF365SWA HNF365SSA, HNF365SSWA HNF366JA HNF366RA S19 77 HNF366SA HNF367, J HNF367R HNF367S HNF368, J, S HNF368R LF111N S2 35 (10) LF111NR S3 35 (10) LF211N S1 35 (10) LF211NR S3 35 (10) LNF222R S5 35 (10) Type 1 or 3R 30A GD Type 1 or 3R A GD, A HD Type VBII Type /X or A HD Type VBII Type 1 or 3R A Type VBII (GD & HD) Type /X or A HD Type VBII * For inches / millimeters conversion, multiply inches by 25.. a Knocks not provided on Type / X and 12 or in 800 & 1200A switches. -2 Siemens Industry, Inc. SPEEDFAX 2017 Product

25 General and Heavy Duty Safety Switches Knockout Diagrams Type 1 & 3R Enclosures SAFETY Removable plate covering HS Type Hub opening (Max. 2.5 Conduit) Removable plate covering HS Type Hub opening (Max. 2.5 Conduit) S8 S9 2 K.O.'s for Conduit 0.75, 1 in. 5 K.O.'s for Conduit 0.50, 0.75, 1 in dia. K.O. 2 K.O.'s for Conduit 0.75, 1 in. 5 K.O.'s for Conduit 0.50, 0.75, 1 in dia. K.O. * For inches / millimeters conversion, multiply inches by 25.. Siemens Industry, Inc. SPEEDFAX 2017 Product -25

26 General and Heavy Duty Safety Switches Knockout Diagrams Type 1 & 3R Enclosures SAFETY * For inches / millimeters conversion, multiply inches by Siemens Industry, Inc. SPEEDFAX 2017 Product

27 Special Application Safety Switches Dimension Drawings Non-Metallic Dimensions Non-Metallic Dimensions (Inches) Non-Metallic H W D A B C E F G J HF321NX HF322NX HF361NX a HF362NX a HF363NX a HF36NX a HNF361X a HNF362X a HNF363X a HNF36X a SAFETY VBII Interlocked Receptacle Switches Dimensions (Inches) A B C D E F G Cr-H Type Fusible (20 & 600V) Cr-H Type Non-Fusible (600V max.) Pyle-National Type Fusible (20 & 600V) Pyle-National Type Non-Fusible (600V max.) a a * For inches / millimeters conversion, multiply inches by 25.. a Dimensions also apply to L suffix switches (less lugs). Siemens Industry, Inc. SPEEDFAX 2017 Product -27

28 Special Application Safety Switches Dimension Drawings -Pole & 6-Pole Dimensions SAFETY & 6-Pole Safety Switch Dimensions Inches (mm) Enclosure Mounting A B C D E F Figure 1, -Pole Fusible and Non-fusible, Type 1 HNF (622) 9.53 (22) 6.09 (155) (83) 6.75 (171) (7) HF (70) 9.53 (22) 6.09 (155) (597) 6.75 (171) (7) HNF (632) (292) 6.09 (155) (83) 9.38 (238) (7) HF (852) (292) 6.09 (155) (699) 9.38 (238) (7) HNF (702) (309) 6.09 (155) (92) 8.00 (203) (7) HF (926) (309) 6.09 (155) (71) 8.00 (203) (7) HNF (91) (86) 6.2 (163) (78) (381) 0. (11) HF6 9.8 (1257) (86) 6.2 (163) 5.50 (1130) (381) 0. (11) Figure 2, & 6-Pole Fusible Type 12/3R and X HF61J, HF661J, (622) 9.53 (22) 6.8 (165) (80) 5.7 (139) 0.27 (7) HF661S HF62J, HF662J, (852) (292) 6.8 (165) (907) 8.00 (203) 0.27 (7) HF662S HF63J, HF663J, 36. (926) (309) 6.8 (165) (982) 8.7 (215) 0.27 (7) HF663S HF6J, HF66J, 9.8 (1257) (86) 6.78 (172) 51.6 (1312) 13. (31) 0.33 (8) HF66S Figure 2, & 6-Pole Non-fusible Type 12/3R and X HNF61J, HNF661J, 2.50 (622) 9.53 (22) 6.8 (165) (667) 5.7 (139) 0.27 (7) HNF661S HNF62J, HNF662J, 2.88 (632) (292) 6.8 (165) (687) 8.00 (203) 0.27 (7) HNF662S HNF63J, HNF663J, 27.5 (700) (309) 6.8 (165) (756) 8.7 (215) 0.27 (7) HNF663S HNF6J, HNF66J, (91) (86) 6.78 (172) (969) 13. (31) 0.33 (8) HNF66S Figure 1: Type 1 Figure 2 : Type 12/3R and X -28 Siemens Industry, Inc. SPEEDFAX 2017 Product

29 Special Application Safety Switches Dimension Drawings Double Throw Selection Description Double throw switches are intended to transfer loads from one power source to another. All 2 & 3-pole double throw switches are suitable for use as service equipment including non-fusible versions when used in combination with a UL listed circuit breaker or fusible switch. All are UL Listed and both horsepower and load break rated. Switches are rated for use on systems up to 10,000A when protected with Class H fuses or 100,000A when protected with Class R or Class T fuses b. They can also be used to connect a single source of power to either of two loads. In this application it is necessary to field modify fusible Double Throw Switches switches so that the fuses are on the load side of the switching mechanism. A cover interlock is provided on all ampere ratings. The operating handle may be padlocked in the off position. Fuse Capabilities of Fusible DTF Switches Amp Fuse Type H R T J 30 & 60A, 20V Std Yes (kit) No No 30 & 60A, 600V Std Yes (kit) No Yes c 100 & 200A Std Yes (kit) Yes (kit) Yes c 00 & 600A (DTF) No No Yes c Std Type 1 Indoor Type 3R Outdoor a Type 12/3R Industrial Type X Stainless Steel System Voltage of Poles Amps Heavy Duty Fusible (30-200A) with Class H fuse spacings Less Neutral b 20 Volt AC or 250 Volt DC 600 Volt AC, 250 Volt DC Heavy Duty Non-Fusible Less Neutral b 20 Volt AC or 250 Volt DC 600 Volt AC, or 250 Volt DC General Duty Non-Fusible 20 Volt AC DTF22s DTF22R 30 DTF321 DTF321Rs 60 DTF322 DTF322Rs DTF323s DTF323R 200 DTF32 DTF32R 00 DTF325 FR325DTK s 600 DTF326s FR326DTK d s 30 DTF DTF362s DTF363 DTF363R F353SSDTK s 200 DTF36 DTF36R F35SSDTK s 00 DTF365 FR355DTK d s F355SSDTK s 30 DTNF DTNF DTNF DTNF22 DTNF22R 00 DTNF225 DTNF225R 30 DTNF DTNF DTNF323 DTNF323R DTNF32 DTNF32R 00 DTNF DTNF DTNF327s 30 DTNF361 DTNF361R DTNF361J DTNF361S 60 DTNF362 DTNF362R DTNF362J DTNF362S 100 DTNF363 DTNF363R DTNF363J DTNF363S DTNF36 DTNF36R DTNF36Js DTNF36S 00 DTNF365 DTNF365R NF355HDTK NF355SSDTK 600 DTNF366 DTNF366R 800 DTNF367 DTNF367R 1200 DTNF368s DTNF368R 30 NFR51DTKs 60 NFR52DTKs 100 NFR53DTKs e 200 NF5DTK NFR5DTKs NF5SSDTKs 00 NF55DTKs NFR55DTKs 600 NF56DTKs NFR56DTKs 800 NF57DTKs NFR57DTKs 2 3 Type 3R Outdoor a Less Neutral Type 3R Outdoor a With Neutral Type 3R Outdoor General Duty With Neutral 100 DTGNF223R DTGNF223NR DTLNF213NR 200 DTGNF22R DTGNF22NR 100 DTGNF323R DTGNF323NR 200 DTGNF32R DTGNF32NR SAFETY s Built to order. Allow 3 weeks for delivery. a Use HS Type hubs for A switches. 00A and larger switches do not have hub provisions. b All Heavy Duty double throw switches with a catalog number starting with DT are rated 200,000 AIC max. when protected by Class R, J or T fuses. Fuse ampere rating must not exceed switch ampere rating. c Move load base. d Will accept class T Fuses only. e -pole switches are not approved for service entrance. Will accept class H fuses only. General duty Stand-by Power Panel catalog number DTLNF213NR contains (2) 100A, 2P circuit breakers rated 120/20V AC & 10,000 AIC. Product Category HDSS Siemens Industry, Inc. SPEEDFAX 2017 Product -29

30 Safety Switches Double Throw Selection SAFETY Accessories, Lug Data and Horsepower s Accessories 2 and 3-Pole Switches Type DT Only a Description 30A HNC & 100A HN263 Neutral Kits 200A HNC26 00 & 600A HN & 1200A HND A (2) #1- AWG HG6123 Equipment 00 & 600A () #1-2/0 HG656 Ground Kit A (8) #6-350 Kcmil HG A with (1) NO & (1) NC contact HA16123 Auxiliary Contacts (HD only) A with (2) NO & (2) NC contacts HA26123 (two required per switch) d A with (1) NO & (1) NC contact HA A with (2) NO & (2) NC contacts HA A, 20V Kit HR21 Class R Fuse Clip Kits 30A, 600V Kit/60A, 20V Kit HR612 (two required per switch) 60A, 600V Kit HR62 100A Kit HR63 200A Kit HR6 100A, 20V Kit HT23 Class T Fuse Adapter Kits 100A, 600V Kit HT63 (two required per pole) 200A, 20V Kit HT2 200A, 600V Kit HT6 For 3 " Conduit ECHS075 For 1" Conduit ECHS100 Type 3R Hubs (30-200A) For 1 1 " Conduit ECHS125 For 1 1 2" Conduit ECHS150 For 2" Conduit ECHS200 For 2 1 2" Conduit ECHS250 Accessories -Pole and Type F & NF 3-Pole Switches Only b Description Auxiliary Switch (1) NO, (1) NC d DS200EK1 (two required per switch) A (2) NO, (2) NC d DS200EK A DS100GK Ground Lug Kit c 200A DS200GK A DS68GK A Use Type HR Hubs Hubs A Use Type SSH, X Hubs A Use Type SSH, X Hubs Neutrals (3-pole only) A DT100NK 200A DT200NK 00 & 600A Fusible DS800NK 00A 3P Non-Fusible DT600NK Wire Ranges (Line, Load and Neutral) per NEC Requirements A 2, 3 & -Pole Switches Switch Wire Range (Cu/Al) New VBII Design Line, Load and Neutral 0 30 (1) # (1) # (1) #1 1/0 AWG 100 (1) #1 1/0 AWG 200 (1) #6 250 kcmil A 2 & 3-Pole Switches Switch Wire Range (Cu/Al) New VBII Design Line, Load and Neutral 00 (1) 1/0 AWG 750 kcmil or (2) 1/0 AWG 250 kcmil 600 (2) 1/0 AWG 500 kcmil 800 (2) 1/0 AWG 750 kcmil or (3) 1/0 AWG 500 kcmil 1200 (3) 1/0 AWG 600 kcmil or () 1/0 AWG 500 kcmil A -Pole switches Switch Wire Range (Cu/Al) New VBII Design Line, Load and Neutral 00 (2) 1/0 AWG 300 kcmil or (1) 1/0 AWG 750 kcmil 600 (2) Kcmil 800 (3) Kcmil Maximum Horsepower s Fused 1-Phase AC 3-Phase AC 250V 20V 20V 80V 600V DC Non-Fused Replacement Parts 2 and 3-Pole Switches Only a Description Type 1, 3R & 12 Replacement Handle A HHD6123 Type X Replacement Handle A HHD6123S Replacement Handle A HHD656 s Built to order. Allow 6 8 weeks for delivery. a For DT VBII Type switches only. b Also for fusible stainless & 00A Type 12 & x switches. c The following ground lugs are provided as standard in 200A and larger switches 200-(1) #1- Cu/Al A-(3) #6-250MCM Cu/Al. d One aux. required for normal and one required for emergency switch line base. -30 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS & RESI

31 Safety Switches Revised on 12/17/17 Dimensions VBII Design Double Throw Dimensions (Inches) Enclosure Mounting A B C D E F Figure 1 ( A Type 1 & 3R) DTNF221, DTNF321, DTNF361, DTNF361R DTF321, DTF321R, DTF DTNF222, DTNF322, DTNF362, DTNF362R DTF322, DTF322R, DTF DTNF223, DTNF323, DTNF323R, DTNF363, DTNF363R, DTGNF223R, DTGNF223NR, DTGNF323R, DTGNF323NR DTF323, DTF323R, DTF363, DTF363R DTNF22, DTNF22R, DTNF32, DTNF32R, DTNF36, DTNF36R, DTGNF22R, DTGNF22NR, DTGNF32R, DTGNF32NR DTF22, DTF22R, DTF32, DTF32R, DTF36, DTF36R DTF325, DTF326, DTF DTNF225, DTNF225R, DTNF325, DTNF365, DTNF365R DTNF326, DTNF366, DTNF366R DTNF327, DTNF367, DTNF367R DTNF368, DTNF368R FR325DTK c, FR355DTK c FR326DTK c NFR51DTK c, NFR52DTK c, NFR53DTK c NF5DTK bc, NFR5DTK bc NF55DTK c, NF56DTK c, NF57DTK c, NFR55DTK c, NFR56DTK c, NFR57DTK c Figure 2 (30-200A Type 12 & X) SAFETY DTNF361J, DTNF361S DTNF362J, DTNF362S DTNF363J, DTNF363S DTNF36J, DTNF36S NF355HDTK ac, NF355SSDTK ac NF5SSDTK c F353SSDTK bc F35SSDTK bc F355SSDTK bc Figure 1 Figure 2 Type 1 & 3R d Type X & 12 * For inches / millimeters conversion, multiply inches by 25.. a (3) Mounting holes supplied (1 at top). b () Mounting holes provided. c These switches are not Type VBII design. d Drip hood not shown but provided on Type 3R enclosures. Siemens Industry, Inc. SPEEDFAX 2017 Product -31

32 Enclosed Switches Rotary Disconnect Switches in Non-Metallic Enclosures e Selection SAFETY Description A non-fusible switches are available in fiberglass reinforced polycarbonate enclosures which are UL approved as Type 12 & X and for either indoor or outdoor use. All are horsepower and load break rated. All are panel mounted and are either supplied with factory installed aux. contacts or will accept contact kits. All are compact in size while providing ample wiring space for copper line & load conductors. Siemens Enclosed Rotary Disconnect Switches b A, Non-Fusible b 600VAC max. rated b Available in both Type 12 and X non-metallic enclosures b Both screw and hinged cover designs available b Listed and marked suitable for use as motor disconnect per NEC Section b Screw cover switches are UL listed under File No. E7705 and are CSA certified under File No b IEC rated and CE marked (enclosures are IP65 rated) b HP rated Horsepower s 3 Pole, 3 Wire with (1) NO Shipping 20V AC 80V AC 600V AC 3 Pole, 3 Wire & (1) NC Aux. Contact hi Weight a 1 Phase 3 Phase 3 Phase 3 Phase Non-Fusible, Type 1, X & 12K b with Screw Cover and Black Rotary Handle 600V AC Max. e b Hinged door switches are UL listed for multiple line and load conductors per phase in A ratings. They are UL & CUL listed under File No. E b Rotary handles are available in black, red, and yellow and in pistol grip designs b 16 63A screw cover switches have factory installed ground bars. All hinge cover switches accept ground lug kits b Screw cover switches are provided with knockouts b Padlockable in OFF position with up to (3) padlocks 16 3LD206-0TB51-0US2 3LD206-1GP51-0US LD216-0TB51-0US2 3LD216-1GP51-0US LD226-0TB51-0US2 3LD226-1GP51-0US LD226-1TS51-0US2 f s LD226-2TW51-0US2 g s LD2565-0TB51-0US2 3LD2565-1GP51-0US2s LD2766-0TB51-0US2 3LD2766-1GP51-0US2s LD2866-0TB51-0US2 3LD2866-1GP51-0US2s Non-Fusible, Type 1, X & 12K b with Screw Cover and Red and Yellow Rotary Handle 600V AC Max. e 16 3LD206-0TB53-0US2 3LD206-1GP53-0US LD216-0TB53-0US2 3LD216-1GP53-0US LD226-0TB53-0US2 3LD226-1GP53-0US LD226-1TS53-0US2 f s LD226-2TW53-0US2 g s LD2565-0TB53-0US2 3LD2565-1GP53-0US2s LD2766-0TB53-0US2s 3LD2766-1GP53-0US2s LD2866-0TB53-0US2s 3LD2866-1GP53-0US2s s Built to order. Allow 6 8 weeks for delivery. a Carton quantity of (1). Shipping weight in pounds (lbs.). b Approved for indoor/outdoor use. No cover interlock provided. c 30 and 60A switches are also rated 600V AC. d Also rated as Type 12 and UL approved for both indoor and outdoor use. Defeatable cover interlock provided. e Screw cover enclosures are constructed from Makrolon 925. Hinged cover enclosures are constructed from fiberglass reinforced polycarbonate. f Switch is supplied with (2) NO and no NC aux. contacts. g Switch is supplied with () NO and no NC aux. contacts. Ground bar is not provided or available. h Aux. contacts break about 3 Ms before and make about 3 Ms after main switch contacts. i 6P, 25A, switch with 1 NO & 1 NC aux. contacts and a black operating handle is also available. Order catalog number 3LD2165-VD51 (Discount Code: Pilot Devices). -32 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS

33 Enclosed Switches Rotary Disconnect Switches Selection Enclosed Disconnect Switch Dimensions (Inches)* Fig. Dimensions No. A B C D 3LD d LD d LD d LD e LD LD Note: 3LD2 Type switches only have top and bottom end KOs as follows: 16-30A - 1/2 & 3/, 63A - 3/ & 1, 100 & 25A - 1 & 1 1/ Figure 1 UL and CUL Short Circuit Withstand s Short Circuit Withstand and Fuse Class With Line Side Fusing With Load Side Fusing a 5 ka at 10 ka at 18 ka at 5 ka at 18 ka at 600V Max 600V Max 80V Max 80V Max 80V Max 3LD2 Type Switches h RK5 16 (50A Max) Wire ranges 60/75 C Cu Only 3LD2 Type Switches c 16 Amps (1) #18-10 AWG Amps (1) #1-10 AWG 63 Amps (1) #1-6 AWG Amps (1) #12-1 AWG HNF Type Switches (1) #1-#10 AWG Solid (1) #1-# AWG Stranded Up to () #12 AWG Solid 30 Amps Up to (3) #12 AWG Stranded Up to (6) #1 AWG Stranded Up to () #1 AWG Stranded with (1) #10 AWG Stranded (1) #1-#10 AWG Solid (1) #1-#1 AWG Stranded (2) #6 AWG Stranded 60 & 100 Amps Up to (3) #8 AWG Stranded Up to (6) #10 AWG Stranded Up to (6) #12 AWG Solid Figure 2 SAFETY 25 & 30 RK5 (80A Max) 63 RK5 (175A Max) 100 & 125 RK5 (200A Max) HNF Type Switches 30 Ferraz Shawmut A50P or lower H, K & RK5 H, K & RK5 let-through (100A Max) (30A Max) semiconductor fuses J, T & CC (60A Max) (100A Max) Ferraz 60 H, K & RK5 Shawmut (150A Max) A50P or lower H, K & RK5 let-through (60A Max) f semiconductor 100 f fuses (100A Max) a For use as supplemental protection on the load side of the branch circuit over current protective device. b Ground lug kit has two lugs for #1- Cu/Al wire. c Factory installed ground lugs supplied as follows: 16-30A #1-10 Cu, 63A #1-8 Cu. Ground lug not provided and is not available on catalog numbers 3LD226-2TW51-0US2 and 3LD226-2TW53-0US2. d 6.38 inches high including mounting feet. e 7.85 inches high including mounting feet. f 60 & 100A HNF switches are rated 10kA at 80V max. with line side Class H, K & RK5 150A max. fuses. g Wire range (1) #1-2 AWG 60/75 C Cu only. h 16-63A 3LD switches are also rated 5kA at 600VAC max when protected by a 3RV type MSP of the same or lesser ampere rating. * For inches / millimeters conversion, multiply inches by 25.. IEC Fuse and Withstand s gg Fuse Size Short Circuit 3LD2 Screw Cover Switches 16 20A 5k Arms 25 25A 10k Arms 32 50A 10k Arms 63 63A 15k Arms A 20k Arms A 20k Arms HNF Hinged Cover Switches 30 63A 10k Arms A 10k Arms A 10k Arms Accessories Switch Description 3LD2 Type Switches c 16 30A 3LD9220-2C Neutral Kit 63A 3LD9250-2CA Neutral Kit A 3LD9280-2C Neutral Kit HNF Type Switches A GSGK60 Ground Lug Kit b 30A LBRA1 Auxiliary Contact Kit (1 NO-1 NC) A LBRA2 Auxiliary Contact Kit (1 NO-1 NC) A HF63CX g Neutral Kit Siemens Industry, Inc. SPEEDFAX 2017 Product -33

34 Enclosed Switches Enclosed Bolted Pressure Switches & Safety Switch Replacement Parts Selection For enclosed bolted pressure contact switches order as lug-in/lug-out single section BPS main switchboards using either the SPACE 2000 Switchboard EPM or COMPAS. VBII Safety Switch Replacement Parts Handle / Handle Guard Line Base Load Base General Duty Heavy Duty Fusible 2- and 3-Pole A General Duty & A Heavy Duty eh SAFETY 30 HD 20V HFB21 b HBB21 b HH6123 g 60 GD HFB612 b HBB612 b GH HD 20V HFB22 b HBB22 b HH6123 g V HFB612 b HBB612 HH6123 g V HFB62 b HBB62 HH6123 g 100 HFB63 b HBB63 GH223 HH6123 g 200 HFB6 b HBB6 GH2 HH6 g 00 HFB65 cf HBB656 HH65678 HH65678 g 600 HFB66 cf HBB656 HH65678 HH65678 g 800 HFB67A bf HBB67A HH65678 g 1200 HFB68 bf HBB68 HH68 g Non-Fusible 3-Pole A General Duty & A Heavy Duty eh 30 HD HNB612 b HH6123 g 60 GD HNB612 b GH HD HNB623 b HH6123 g 100 HNB623 b GH223 HH6123 g 200 HNB6 b GH2 HH6 g 00 HNB65 cf HH65678 HH65678 g 600 HNB66 cf HH65678 HH65678 g 800 HNB67A bf HH65678 g 1200 HNB678 f HH68 g Mechanism Assembly Line & Load Lugs Fusible 2- and 3-Pole A General Duty & A Heavy Duty eh 30 HD 20V HM6123 g HL612 a 60 GD HM6123 HL612 a 60 HD 20V HM6123 g HL612 a V HM6123 g HL612 a V HM6123 g HL612 a 100 HM6123 g HL63 a 200 HM6 g HL6 a 00 HM65 HL65678 d 600 HM66 HL65678 d 800 HM67A HL67A fi 1200 HM678 i Non-Fusible 3-Pole A General Duty & A Heavy Duty eh 30 HD HM6123 g HL612 a 60 GD HM6123 HL612 a 60 HD HM6123 g HL612 a 100 HM6123 g HL63 a 200 HM6 g HL6 a 00 HM65 HL65678 d 600 HM66 HL65678 d 800 HM67A HL67A fi 1200 HM678 i Internal Shield Kits These kits provide an inner door on safety switches to prevent accidental contact with live parts. All kits are constructed from clear plastic, provide test probe holes and allow replacement of fuses without the removal of the kit. Switch UPC Code _ For use with Fusible Type 1, 3R, 12 and X Stainless Steel Enclosed Safety Switches HSK61SSW HSK62SSW HSK63SSW HSK6SSW For use with Fusible Type VBII Disconnect Switches HSK HSK & HSK HF362 with HSK62SSW installed VBFS361F with HSK61 Installed a Three lugs included in kit. b Includes lugs. c Lugs not included. d One lug per kit. e One per switch required unless otherwise noted. f One required per pole. g For type /X stainless steel switches add S to end of catalog number. h For replacement door for heavy duty switches add DOOR to end of switch catalog number. i Lugs included with line and load bases. Not for use with Non-metallic safety switches -3 Siemens Industry, Inc. SPEEDFAX 2017 Product Product Category HDSS