Grid-Tied Photovoltaic System AC Rating: kw DC Rating: kw Meehan, Kevin 793 Mason Road Ashby, MA Jurisdiction: Town of Ashby

Transcription

1 1061 NSI Full Bleed B (11.00 X Inches) Scope of Work: Energy shall install a 1. kw Grid-tied Photovoltaic ("PV") System totaling (1) Solarworld Plus SW 8 Mono Black Modules with (1) Enphase Energy M0-60-LL-S Micro- Inverter(s). The Modules shall be flush mounted on the asphalt/comp. shingle roof and interconnected via supply side tap. Equipment Specifications: Module: (1) Solarworld Plus SW 8 Mono Black Inverter 1: (1) Enphase Energy M0-60-LL-S Racking: UniRac SolarMount ttachment Flashing: UNIRC UniRac Flat Flashing Roof Specifications: Roof 1: " x 8" 16" O.C. Eave Height: ft Pitch: 0 zimuth: 7 rray Size: 18 Modules Roof : " x 8" 16" O.C. Eave Height: 1 ft Pitch: 0 zimuth: 7 rray Size: 10 Modules Site Specifications: Occupancy: II Design Wind Speed: 90 MPH Exposure Category: B Mean Roof Height: ft Ground Snow Load: 0 PSF dj. Roof Snow Load: 8. PSF Roof : " x 8" 16" O.C. Eave Height: ft Pitch: 0 zimuth: 9 rray Size: 17 Modules ll Work to be in Compliance with: 01 National Electrical Code (NEC) 009 International Residential Code (IRC) 009 International Building Code (IBC) 01 International Fire Code (IFC) 01 Uniform Mechanical Code (UMC) 01 Uniform Plumbing Code (UPC) M 780 CMR, 8th Edition -including //11 revisions to Tables R01.() & R01.() SCE/NSI 7-0 Minimum Design Loads for Buildings and Other Structures s amended and adopted by Town of shby Roof : " x 8" 16" O.C. Eave Height: 1 ft Pitch: 0 zimuth: 9 rray Size: 6 Modules Grid-Tied Photovoltaic System C Rating: 1.0 kw DC Rating: 1. kw Meehan, Kevin 79 Mason Road shby, M 011 Jurisdiction: Town of shby General Notes: 1. System follows any/all Fire Code Setbacks per Ordinances of the Town Of shby.. ll projects will comply with the Ordinances of the Town of shby.. Construction Hours: 7am-8pm Monday-Friday, 9am-8pm Saturday, No time on Sunday or legal Holidays.. Product Data Sheets shall be included.. Rooftop penetrations shall be completed and sealed per code by a licensed contractor. 6. ll Photovoltaic modules shall be tested and listed by a recognized laboratory. 7. Certifications shall include UL170, IEC6166, IEC continuous ground shall be provided for the rray and for all Photovoltaic Equipment. 9. DC Wiring shall be run in metal conduit or raceways within enclosed spaces in a building. 10. Conduit, Wire systems and Raceways shall be located as close as possible to ridges, hips, and outside walls. 11. Conduit between Sub rrays and to DC Combiners/Disconnects shall use guidelines that minimize the total amount of conduit by taking the shortest path. 1. Space Requirements for electrical equipment shall comply with NEC rticle Equipment grounding shall be sized in accordance with Table Connectors that are not readily accessible and that are used in the circuits operating at or over 0V C or DC shall require a tool for opening and are required to be marked "Do not disconnect under load" or "Not for current interrupting", per 690. (c) & (e). 1. ll signage to be placed in accordance with local building code. 16. Signs or Directories shall be attached to the electrical equipment or located adjacent to the identified equipment. 17. Signs should be of sufficient durability to withstand the environment. 18. ny plaques shall be metal or plastic with engraved or machine printed letters, or electro-plating, in a red background with white lettering, a minimum of /8" height and all capital letters. 19. For Inverter C Rating, refer to "Rated (continuous) output power" in specification sheet for inverter specified. Sheet List Sheet No. Sheet Title PV-000 COVER PV-01 SITE PLN PV-0 MODULE LYOUT PV-0 MODULE LYOUT () PV-0 DETILS PV-0 MTERILS PV-E01 ELECTRICL DIGRM PV-E0 SYSTEM CLCS PV-G01 SIGNGE 1 LM 10/19/ Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # COVER 8's Modules PV-000

2 Equipment Specifications: Module: (1) Solarworld Plus SW 8 Mono Black Inverter 1: (1) Enphase Energy M0-60-LL-S Racking: UniRac SolarMount ttachment Flashing: UNIRC UniRac Flat Flashing Roof Specifications: Roof 1: " x 8" 16" O.C. Eave Height: ft Pitch: 0 zimuth: 7 rray Size: 18 Modules Roof : " x 8" 16" O.C. Eave Height: ft Pitch: 0 zimuth: 9 rray Size: 17 Modules Roof : " x 8" 16" O.C. Eave Height: 1 ft Pitch: 0 zimuth: 9 rray Size: 6 Modules Roof : " x 8" 16" O.C. Eave Height: 1 ft Pitch: 0 zimuth: 7 rray Size: 10 Modules 106 Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC (E) Property Line 79 MSON ROD SHBY, M 011 Project # NSI Full Bleed B (11.00 X Inches) Mason Road NOTE: LL EXTERIOR CONDUIT ON ROOF ND UNDER EVES FINL LOCTIONS TO BE DETERMINED DURING INSTLLTION (E) Driveway Equipment on Exterior Wall: (E) Utility Meter (N) J-Box - P.O.I. via Supply Side Line Tap (N) PV C Disconnect - Fused (N) PV C Combiner Panel (N) PV Prod. Monitor Equipment on Interior Wall: (E) Main Service Panel (E) Critical Load Panel w/ Plug -In Generator (E) Sub-Panel (N) PV rray : 10 Solarworld Plus SW 8 Mono Black Modules (N) PV rray 1: 18 Solarworld Plus SW 8 Mono Black Modules (E) Single Family Dwelling 79 MSON ROD (E) Deck (N) PV rray : 17 Solarworld Plus SW 8 Mono Black Modules (N) PV rray : 6 Solarworld Plus SW 8 Mono Black Modules (E) Detached Garage 1 LM 10/19/ " = ' 8's Modules SITE PLN PV-01

3 PV RRY 1 - MECHNICL LODS rray rea: 6.9 ft² Total Photovoltaic Dead Load:.99 psf rray Weight: 977. lbs vg. Dead Load per nchor: 17. lbs nchor Qty.: 6 PV RRY - MECHNICL LODS rray rea: 17.7 ft² Total Photovoltaic Dead Load:.11 psf rray Weight: 6.8 lbs vg. Dead Load per nchor: 17.1 lbs nchor Qty.: Design Values by Roof Zone: Corner Egde Interior Max. UniRac Rail Span: 8 in. O.C. 8 in. O.C. 8 in. O.C. Max. UniRac Rail Cantilever: 16 in. O.C. 16 in. O.C. 16 in. O.C. djusted nchor Span: in. O.C. in. O.C. in. O.C. Downforce Point Load: 07.6 lbs 07.6 lbs 07.6 lbs Uplift Point Load: lbs lbs -7. lbs Minimum nchor Strength: 00 lbs verage Safety Factor:.99 '-6" '-8" 9'-9" '-6" Design Values by Roof Zone: Corner Egde Interior Max. UniRac Rail Span: 8 in. O.C. 8 in. O.C. 8 in. O.C. Max. UniRac Rail Cantilever: 16 in. O.C. 16 in. O.C. 16 in. O.C. djusted nchor Span: in. O.C. in. O.C. in. O.C. Downforce Point Load: 0. lbs 0. lbs 0. lbs Uplift Point Load: -9.0 lbs -9.9 lbs lbs Minimum nchor Strength: 00 lbs verage Safety Factor: Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # NSI Full Bleed B (11.00 X Inches) ' (N) PV rray on Roof 1: 18 Solarworld Plus SW 8 Mono Black Modules 18 Enphase Energy M0-60-LL-S Micro-Inverters Roof " X 8" 16" O.C. Pitch:0 zimuth:7 11' '-6" 17'-6" ' 16'-6" 6' UniRac SolarMount Mounting Notes: Integrated Full System Grounding and Bonding to UL 70 Total Quantity of ttachments =16 Roof Zones are defined by dimension, a =.0 ft. (N) PV rray on Roof : 10 Solarworld Plus SW 8 Mono Black Modules 10 Enphase Energy M0-60-LL-S Micro-Inverters Maximum llowable Cantilever for UniRac Rail is 1 Roof the Maximum Rail Span Racking and ttachment: UniRac SolarMount with UNIRC UniRac Flat Flashing attached with /16" x -1/" Lag Bolt, Hex Head, 18-8 SS " X 8" 16" O.C. ll Dimensions shown are to module edges, including 1/ in. Spacing between Modules required when using the Top Clamp Method. Pitch:0 The SolarMount Rails will extend 1-1/ in. beyond the Module Edge in order to support the End Clamps. zimuth:7 UniRac requires one thermal expansion gap ( in.) for continuous sections of rail greater than 0' in length rray Installed according to the UniRac SolarMount Design & Engineering Guide PUB1NOV0 ttachment Locations, If shown, are approximate. Final adjustment of attachment location may be necessary depending on field conditions. ll attachments are staggered amongst the framing members. 11' ' 1 LM 10/19/016 /16" = 1'-0" 8's Modules MODULE LYOUT PV-0

4 PV RRY - MECHNICL LODS rray rea: 08.7 ft² Total Photovoltaic Dead Load:.01 psf rray Weight: 90.7 lbs vg. Dead Load per nchor: 17.9 lbs nchor Qty.: Design Values by Roof Zone: Corner Egde Interior Max. UniRac Rail Span: 8 in. O.C. 8 in. O.C. 8 in. O.C. Max. UniRac Rail Cantilever: 16 in. O.C. 16 in. O.C. 16 in. O.C. djusted nchor Span: in. O.C. in. O.C. in. O.C. Downforce Point Load: 07.9 lbs 07.9 lbs 07.9 lbs Uplift Point Load: lbs lbs lbs Minimum nchor Strength: 00 lbs verage Safety Factor:.68 '-6" '-8" 9'-9" (E) Roof Obstructions: Roof : Vent Pipe (1) '-6" PV RRY - MECHNICL LODS rray rea: ft² Total Photovoltaic Dead Load:.99 psf rray Weight: 6.1 lbs vg. Dead Load per nchor: 0. lbs nchor Qty.: 16 Design Values by Roof Zone: Corner Egde Interior Max. UniRac Rail Span: 8 in. O.C. 8 in. O.C. 8 in. O.C. Max. UniRac Rail Cantilever: 16 in. O.C. 16 in. O.C. 16 in. O.C. djusted nchor Span: in. O.C. in. O.C. in. O.C. Downforce Point Load: 07.7 lbs 07.9 lbs 07.9 lbs Uplift Point Load: lbs lbs lbs Minimum nchor Strength: 00 lbs verage Safety Factor:.66 Equipment Specifications: Module: (1) Solarworld Plus SW 8 Mono Black Inverter 1: (1) Enphase Energy M0-60-LL-S Racking: UniRac SolarMount ttachment Flashing: UNIRC UniRac Flat Flashing 106 Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # LM 10/19/016 8's Modules 1061 NSI Full Bleed B (11.00 X Inches) ' 16' 1'-" 9'-11" (N) PV rray on Roof : 17 Solarworld Plus SW 8 Mono Black Modules 17 Enphase Energy M0-60-LL-S Micro-Inverters Roof " X 8" 16" O.C. Pitch:0 zimuth:9 16'-6" '-6" (N) PV rray on Roof : 6 Solarworld Plus SW 8 Mono Black Modules 6 Enphase Energy M0-60-LL-S Micro-Inverters Roof " X 8" 16" O.C. Pitch:0 zimuth:9 UniRac SolarMount Mounting Notes: Integrated Full System Grounding and Bonding to UL 70 Total Quantity of ttachments =16 Roof Zones are defined by dimension, a =.0 ft. Maximum llowable Cantilever for UniRac Rail is 1 the Maximum Rail Span Racking and ttachment: UniRac SolarMount with UNIRC UniRac Flat Flashing attached with /16" x -1/" Lag Bolt, Hex Head, 18-8 SS ll Dimensions shown are to module edges, including 1/ in. Spacing between Modules required when using the Top Clamp Method. The SolarMount Rails will extend 1-1/ in. beyond the Module Edge in order to support the End Clamps. UniRac requires one thermal expansion gap ( in.) for continuous sections of rail greater than 0' in length rray Installed according to the UniRac SolarMount Design & Engineering Guide PUB1NOV0 ttachment Locations, If shown, are approximate. Final adjustment of attachment location may be necessary depending on field conditions. ll attachments are staggered amongst the framing members. 1'-" 9'-11" '-9" 11' 1'-10" /16" = 1'-0" MODULE LYOUT () PV-0

5 m Plus SW 8 Mono Black " X 8" 16" O.C. Module Rooftop Sheathing " X 8" 16" O.C. Rail & nchor ssembly UniRac Top-Clamp UniRac SolarMount Rail UniRac Standard L-Foot UNIRC UniRac Flat Flashing (1) /16" x -1/" S.S. Lag Bolt with -1/" Minimum Embedment 106 Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # ttachment Profile Scale: /" = 1'-0" ttachment Detail Scale: 1" = 1'-0" Roof Framing PV Module 16" Max Rail Overhang 1 LM 10/19/016 8's Modules Roof nchor & Flashing Landscape: ~7.1 in. Portrait: ~1.0 in NSI Full Bleed B (11.00 X Inches) nchors located on alternate roof framing members " Max nchor Spacing SolarMount Rail Staggered ttachment Detail (Typ.) Rail Splice Stagger splice locations within the each row of modules Rail Splice Detail 16" Max Rail Overhang Min of supports on either side of splice with a max spacing of 8" Landscape: ~. in. Portrait: ~0.0 in. 6.9 in. 1.0 in. 9. in. Mounting Holes Solarworld Plus SW 8 mono black B Distance from Module Corner Minimum Maximum Long Side, 9. in. 16. in. Short Side*, B.7 in. 9. in. *Top-Clamps may be used on the Short Sides of the Module UL pproved Mounting Locations B 6 WEEBLug Ground Wire SS Bolt SS Flat Washer Grounding Lug & Rail SS Washer & Nut Unirac Rail SS Bolt VRIES DETILS PV-0

6 1 Roof Zones for Enclosed Buildings Suggested Bill of Materials NOTE: Materials Listed below are subject to change during final Installation NSI Full Bleed B (11.00 X Inches) PRT DESCRIPTION PRT NUMBER QTY PHOTOVOLTIC MODULES SOLRWORLD Plus SW 8 mono black Plus SW 8 mono black 1 INVERTERS Enphase Energy M0-60-LL-S M0-60-LL-S 1 - Enphase Monitoring Envoy S RGM ENV-S-MI-10 1 ROOF MOUNT MTERILS UniRac SolarMount Rails& Components SM RIL 168" DRK 10168D 1 - SM ENDCLMP B DRK L 001D 8 - SM BND MIDCLMP BC DRK SS 007D 68 - BND SPLICE BR SERRTED DRK 0018D 1 - nchors & Mounting Brackets L-FOOT SERRTED W/ T-BOLT, DRK 0001D 1 - /16" x -1/" Lag Bolt, Hex Head, 18-8 SS /16X1-1/ FENDER WSHER SST W118FS 1 - NCHOR BSE - UNIRC FLT FLSHING 00010D 1 ELECTRICL BLNCE OF SYSTEM Micro-Inverter ccessories Enphase Engage Trunk Cable, 0 VC, Portrait - (Per Connector) ET Enphase Branch Terminator ET-TERM Enphase Sealing Cap ET-SEL Enphase Cable Wire Clip ET-CLIP /-0 Serrated Flange Nut S/S MICRO MNT BND T-BOLT 1/ INX / SS 00801S 1 - Combiner Sub-Panels, Circuit Breakers Inverter Breaker(s) - THQL10 GE TYPE BR BREKER 0/ THQL C Disconnects and Fuses TGNR GE 60/P GD NON-FUSIBLE SFETY SWTICH 0V TGNR 1 - TGR 1 - Ferraz Shawmut Fuse_ RK_ 70_ 600VC/600VDC_ Time Delay TRS-70R - TGK TERMINL GROUND BR KIT GETGK - Grounding, Wire and Conduit GROUND WEEBLUG #1 (980011) WEEBL Wiley Electronics cme Cable Clips for PV Wire WEEB-CC-PV 0 - SolaDeck PV Roof-Mnt Encl w/dual Grnd lug_6" DIN Rail SD786 1 LM 10/19/ Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # 's Modules MTERILS PV-0

7 Notes: 1. ll conduit to use water-tight expansion fittings.. ll Rooftop conduit to be a minimum of 1" above the roof surface.. PV Connection into Load Center shall be positioned at the opposite end from the Utility Input feeder location.(where applicable). ll equipment to be rated NEM-R unless otherwise noted.. Lowest expected ambient temperature based on SHRE min. mean extreme dry bulb temperature for SHRE location most similar to installation. 6. Highest continuous ambient temperature based on SHRE highest month % dry bulb temperature for SHRE location most similar to installation. 7. ll conductors to be copper unless noted otherwise. 8. Conductor sizing shall limit Voltage drop to % DC & 1.% C (% for Enphase Systems). 1. kw DC(STC) PV System: 1 Solarworld Plus SW 8 mono black Modules with 1 Enphase Energy M0-60-LL-S Micro-Inverters Branch of 9 - rray 1 Branch of 9 - rray 1 WIRE SCHEDULE WIRE SIZING VOLTGE DROP Ground 90 C Derated mapacity 7 C Tag Qty Conductor Size & Type Conduit Length V. Drop Size & Type ( llowable mps x Temp Derate x Fill Derate ) mpacity 6 #1 WG ENGGE CBLE #6 WG BRE Cu FREE IR 0 X 0.76 = N/ 0.6% B 18 #10 WG THWN- #8 WG THWN- 1" EMT (min) 0 X 0.76 X 0. = Ft 1.0% C # WG THWN- #8 WG THWN- 1" EMT (min) 9 X 1 X 1 = Ft 0.1% D # WG THWN- N/ 1" EMT (min) 9 X 1 X 1 = Ft 0.1% B INTERIOR, GRGE (N) Enphase Envoy Envoy S RGM Ethernet SYSTEM LBELING SPECIFICTIONS Max. DC Voltage (- C):.6 V DC Max. Current: 1.0 DC Operating Voltage: 1. V DC Operating Current: 9.0 C Nominal Voltage: 0 V Max. C Current: 1.0 EXTERIOR (E) Overhead Service Drop: 0V: 10V Split Phase DC ---- C 1.8% 1 LM 10/19/ Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # 's Modules 1061 NSI Full Bleed B (11.00 X Inches) Branch of 9 - rray Branch of 8 - rray Branch of 6 - rray Branch of 10 - rray (N) Junction Box (N) Junction Box (N) Junction Box (N) C Combiner 1, 0 Vac 1-Phase, 1 Space NEM R Encl G N C (N) Fused C Disconnect 100, 0 Vac -Pole, NEM R 70 (N) J-Box - P.O.I. via Supply Side Line Tap D (N) #6 GEC Bonded to existing GEC with Irreversible Crimp G M N GEC Ground (E) 00 (E) MSP 00 Rated Cutler-Hammer G (E) CLP w/ Plug- In Generator ELECTRICL DIGRM (N) Junction Box Rooftop Electrical Exterior, djacent to Utility Meter Interior, Garage PV-E01

8 1061 NSI Full Bleed B (11.00 X Inches) MODULE SPECIFICTIONS Solarworld Plus SW 8 Mono Black STC Rating: 8 W Height: 6.9 in. PTC Rating: 6 W Width: 9. in. V MP: 1. V Depth: 1.0 in. I MP: 9.0 rea: 18.0 ft² V OC: 9.7 V Weight: 9.7 lbs I SC: 9.8 Max. Fuse: 1.00 Temp. Coeff. (V OC): %/ C INVERTER 1 SPECIFICTIONS Enphase Energy M0-60-LL-S Nominal V C: 0 V Max. W DC: 00 W Max. W C: 0 W Startup Voltage: V Min. V MP: 16 V Max. V MP: 8 V Max. V DC: 8 V Max. I DC: 1 Max. I C: 1.00 CEC Efficiency: 96.% TEMPERTURES mbient Low Temperature: - C mbient High Temperature: 0 C Temp. Rise for Voltage Calculations: 1 C Temp. Rise for Exposed Conduit on Roof: C SYSTEM LBELING SPECIFICTIONS Max. DC Voltage (- C):.6 V DC Max. Current: 1.0 DC Operating Voltage: 1. V DC Operating Current: 9.0 C Nominal Voltage: 0 V Max. C Current: 1.0 INVERTER 1 CURRENTS DC Max. Current: MODULE Isc x 1. DC Operating Current: MODULE Imp Source Current, I DC: MODULE Isc x 1. x x 1. = = x 1. x 1. = 1.8 Output Current, I C: INVERTER Iac x INVERTER QTY x 1. 1 x 1. x 1 = 6.7 INVERTER 1 LBELING SPECIFICTIONS Max. DC Voltage (- C):.6 V DC Max. Current: 1.0 DC Operating Voltage: 1. V DC Operating Current: 9.0 C Nominal Voltage: 0 V Max. C Current: 1.0 DC Max. Voltage (- C): DC Operating Voltage: INVERTER 1 VOLTGES MODULE Voc x TEMP DELT x TEMP COEF Voc MODULE Vmp 9.7V x 8 x =.6 V 1.V = 1. V 1 LM 10/19/ Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # 's Modules ELECTRICL CLCS PV-E0

9 1" PHOTOVOLTIC POWER SOURCE 1" 6 1 " NEC rticle 690.1(G)()() HT#: REFLECTIVE MTERIL REQUIRED CONDUIT RCEWYS EVERY 10 FEET OR LESS " PHOTOVOLTIC C DISCONNECT NEC rticles & 690.1(B) HT#: C DISCONNECTS CUTION: SOLR ELECTRIC 1" SYSTEM CONNECTED NEC rticles & 690.1(B) HT#: PRODUCTION / NET METERS, MIN SERVICE DISCONNECT DO NOT DISCONNECT 1" UNDER LOD 6 1 " NEC rticle 690.(E)() HT#: BREKER PNEL " 6 1 " 8 1 " CUTION CIRCUIT IS BCKFED NEC rticles 70.1(D)() & HT#: BREKER PNELS 106 Route, Suite 10 Franklin, CT 0678 (1) 68- Fax License# kW STC 79 MSON ROD SHBY, M 011 Project # NSI Full Bleed B (11.00 X Inches) " " PHOTOVOLTIC C DISCONNECT MXIMUM C OPERTING CURRENT: NOMINL OPERTING C VOLTGE: NEC rticles 690. & 690.1(B) HT#: INVERTER 1 C DISCONNECT 1 " V 1 EQUIPPED WITH " RPID SHUTDOWN NEC rticle 690.6(C) HT#: REFLECTIVE MTERIL REQUIRED RPID SHUTDOWN DISCONNECT, MIN SERVICE DISCONNECT " " 1 8 " ELECTRICL SHOCK HZRD IF GROUND FULT IS INDICTED NORMLLY GROUNDED CONDUCTORS MY BE UNGROUNDED ND ENERGIZED NEC rticle 690.(C) HT#: STRING INVERTERS, PRODUCTION / NET METERS, BREKER PNELS 1 8 " ELECTRICL SHOCK HZRD THE DC CONDUCTORS OF THIS RE UNGROUNDED ND MY BE ENERGIZED " " " " 1 8 " INVERTER OUTPUT CONNECTION. DO NOT RELOCTE THIS OVERCURRENT DEVICE. NEC rticle 70.1(D)()(B) HT#: BREKER PNELS 1 8 " DUL POWER SOURCE SECOND SOURCE IS NEC rticles 70.1(D)() & HT#: PRODUCTION / NET METERS, BREKER PNELS 1 8 " TURN OFF PHOTOVOLTIC C DISCONNECT PRIOR TO WORKING INSIDE PNEL NEC rticle 110.7(C) HT#: COMBINER BOXES, EMT ENCLOSURES, BREKER PNELS, MIN SERVICE DISCONNECT 1 8 " ELECTRICL SHOCK HZRD DO NOT TOUCH TERMINLS TERMINLS ON BOTH LINE ND LOD SIDES MY BE ENERGIZED IN THE OPEN POSITION 1 LM 10/19/016 SIGNGE 8's Modules NEC rticle 690.(F) HT#: REQUIRED FOR UNGROUNDED SYSTEMS COMBINER BOXES, CONDUIT ENCLOSURES, DC DISCONNECTS, BREKER PNELS NEC rticle (E) HT#: COMBINER BOXES, EMT ENCLOSURES, C & DC DISCONNECTS, BREKER PNELS, MIN SERVICE DISCONNECT PV-G01