SSW06 Soft-Starter. Motors Automation Energy Transmission & Distribution Coatings

Transcription

1 SSW06 Soft-Starter Motors Automation Enery Transmission & Distribution Coatins

2 VERSATILITY AND HIGH PERFORMANCE Soft-starters are drives desined for the smooth acceleration and deceleration of three-phase induction motors by controllin the voltae applied to the motor. Microprocessed and fully diital, the SSW06 line of soft-starters was developed with cuttin-ede technoloy, ensurin the best performance in the start and stop of induction motors. The line has an advanced operatin interface that allows easy parameter settin, built-in Pump Control function, providin effective pump control, in addition to the torque control function, which allows accelerations and decelerations with linear speed ramps. Main Characteristics SoftPLC Built-in Prorammable Loic Controller Software (unique on the market) Kick Start Function to start loads with hih static friction Bypass incorporated to the Soft-Starter (10 to 820 A), providin size reduction and enery savins Pump Control Function for smart control of pumpin systems, preventin Water Hammer in pumps and hydraulic systems Full electronic motor protection Loner lifespan of the motor and mechanical devices of the driven machine Easy operation, prorammin and maintenance via humanmachine interface Detachable human-machine interface with double display (LED/LCD) 2 SSW06 - Soft-Starter

3 Benefits Fault dianosis, recordin: voltae, current and status of the soft-starter at the error event Actuation level adjustment of the prorammable faults 32-bit, RISC type, hih-performance microcontroller Built-in electronic thermal relay Fully prorammable control types Totally flexible torque control Limitation of current peaks on the line Limitation of voltae drops at the start Voltae (220 to 575 V ac) or (575 to 690 V ac) Switched-mode power supply of the electronics with EMC filter (94 to 253 V ac) Monitorin of the control section voltae, allowin the backup of the motor thermal imae values Protection aainst over and undervoltae on the motor Protection aainst voltae and current imbalance on the motor Protection aainst overload on the motor due to over and under: current, power or torque Input for the motor PTC Elimination of mechanical shocks Great reduction of the stresses on couplins and drivin devices (ear units, pulleys, ears, belts, etc.) Simpler electrical installation Oriented start-up Option of standard connection (3 cables) or motor inside delta connection (6 cables) All the protections and functions are available in the two connection types (unique on the market) Error-protection functions in serial or Fieldbus communication Chane of speed direction possibility JOG function in frequency for both speed directions without contactor Three brakin methods to stop the motor and the load more quickly, with or without contactor Operation in environments at up to 55 C (without current deratin for model rane 10 A to 820 A) Operation in environments at up to 40 C (without current deratin for model rane 950 A to 1,400 A above 40 C) SSW06 - Soft-Starter 3

4 Applications Chemical and Petrochemical Cement and Minin Steel and Metallury Pulp and Paper Food and Beverae Suar and Ethanol Plastic and Rubber Textile Glass Water and Wastewater Ceramic Wood Refrieration Material Handlin 4 SSW06 - Soft-Starter

5 Comparison Current Direct on-line starter Star/delta starter Soft-starter Time Voltae and Current Protections Over and Undervoltae It allows settin the over and undervoltae limits for complete motor protection. Available in both types of connection to the motor. Over Under Voltae Nominal Undervoltae Over. Under Voltae Nominal Overvoltae Current Current Over and Undercurrent It allows settin the over and undercurrent limits for full motor protection. Over Under Nominal Undercurrent Over Under Nominal Overvoltae Built-In Bypass Over and Undervoltae Built-in bypass minimizin the power losses and heat dissipation on the thyristors, reducin space and savin enery. Available in the model rane 10 to 820 A. Three-phase power supply Tree-phase motor SSW06 - Soft-Starter 5

6 Startin Methods Voltae Ramp It allows the smooth acceleration and/or deceleration by means of voltae ramps. Voltae Acceleration Current Ramp It allows settin hiher or lower current limits for the beinnin of the start. Applied to loads with low or hih initial torque. Current Voltae ramp or Pump control Limit current Reular current 0 Fixed current limit Pump Control The pump control provides a smooth deceleration that avoids the Water Hammer. 0 Current Voltae Acceleration Deceleration Limit current Reular current 0 Voltae ramp or Pump control 0 Fixed current limit Current Limitation It allows settin the current limit durin the start accordin to the application requirements. 0 Current Limit current Fixed current limit Reular current Torque Control The SSW06 has an extremely hih performance and totally flexible torque control alorithm in order to meet the requirements of any application, for both startin and stoppin the motor. Available in two motor connection types: standard connection (three cables) or motor inside delta connection (six cables). 1 set point: constant torque 2 set points: linear torque ramp 3 set points: quadratic torque ramp Such type of control allows the acceleration and deceleration with linear speed ramp. Voltae or Current Kick Starter It allows an initial voltae or current pulse that boosts the motor startin torque, which is necessary to start loads with hih static friction. Torque Constant torque Rated torque Voltae Voltae Kick Starter Nominal voltae 0 Torque control with 1 set point Torque Linear torque Rated torque Voltae ramp 0 Current Rated current Torque Quadratic torque 0 Torque control with 2 set points Torque nominal 0 Current limitation 0 Torque control with 3 set points 6 SSW06 - Soft-Starter

7 Operatin Interface Smart Interface Smart operatin interface with double display - LEDs (7 sements) and LCD (2 lines of 16 characters) - which provides excellent visualization as well as a detailed description of all parameters and messaes via alphanumeric LCD display. Selectable Lanuae The smart operatin interface also enables the user to choose the lanuae for the prorammin, readin and presentin the parameters and alphanumeric messaes throuh the LCD display. The reat hardware and software capacity of the product provides the user several lanuae options, such as Portuuese, Enlish, German and Spanish in order to adjust it to any user around the world. LED display (7 sements) Selects (toles) the display between the parameter number and its value LCD display Starts the motor Increases the parameter number or parameter value Decreases the parameter number or parameter value Stops the motor Resets the soft-starter after Local LED Remote LED Chanes the speed direction (check availability) Selects the oriin of the commands/ reference Reverse LED Forward LED JOG function (in frequency) Copy Function The smart interface also incorporates the Copy function, which allows copyin the parameter settin from one soft-starter to others, providin prorammin aility, reliability and repeatability in applications of serially manufactured machines. SSW06 HMI HMI SSW06 Soft-starter A Soft-starter B Oriented Start-Up Soft-starters are devices desined to start induction motors, whose adaptation and performance are directly related to their characteristics and of the power supply line. The SSW06 soft-starters contain a prorammin wizard especially developed to speed up the product start-up. Such resource uides the user in the settin of the minimum characteristics necessary for a perfect adaptation of the soft-starter to the motor and the load. SSW06 - Soft-Starter 7

8 Fieldbus Communication Networks The SSW06 soft-starter can be interconnected in Fieldbus fast communication networks throuh the most widely used standardized protocols in the world, namely: Fieldbus Profibus-DP (optional) DeviceNet (optional) Modbus-TCP EtherNet/IP Modbus-RTU RS232 (built-in) Modbus-RTU RS485 (optional) Especially desined to interate lare industrial automation plants, the fast communication networks provide advantaes such as complete and on-line supervision, monitorin and control of the soft-starter, deliverin hih performance and reat operational flexibility. For the interconnection in Fieldbus, Profibus-DP or DeviceNet communication networks, the SSW06 soft-starters allow installin a network board accordin to the desired protocol. For the interconnection in Fieldbus and Modbus-RTU communication networks, a connection via RS232 (available) or RS485 (optional) interface can be used. Additionally to the advantaes in monitorin the protections and drivin the motor, diital and analo inputs and outputs can be used as a mini-remote of the Fieldbus network master. PLC FIELDBUS NETWORKS... 8 SSW06 - Soft-Starter

9 SuperDrive G2 Software in Windows environment for parameter settin, control and monitorin of the SSW06. Automatic identification of the SSW06 Readin of parameters of the SSW06 Writin of parameters to the SSW06 Edition of parameters of the SSW06 online Edition of parameters offline on the PC Possibility to create the whole application documentation Easily accessible Parameter settin, control and monitorin of the SSW06 is possible via SuperDrive G2 software Supplied with a 3 m RS232 serial cable when the SuperDrive G2 software is purchased Free software on SoftPLC Function It is a resource that adds the functionalities of a PLC to the SSW06, providin the users with flexibility and allowin the development of their own applications (user s prorams). LADDER prorammin lanuae - WLP Software Access to all parameters and I/Os of the SSW06 PLC mathematical and loical blocks Download, upload and online monitorin Memory capacity of 1 Kbytes Online help 18 parameters, 4 errors, 4 alarms of the user which can be prorammed individually Free software on SSW06 - Soft-Starter 9

10 Accessories Operatin Interface with Double Display LEDs and LCD with complete resources via codes and messaes with alphanumeric texts and Copy function for local installation (soft-starter cover) or remote installation on panel door. Maximum distance 5 m (without frame). HUMAN-MACHINE INTERFACE COMPLETE (standard) HMI-SSW06-LCD Frame to Install/Mount the HMI For remote installation of the HMI transferrin the soft-starter operation to the panel door or a machine console. Maximum distance of 5 m. Deree of protection: IP42 FRAME KIT FOR REMOTE INTERFACE KMR-SSW06 Cable to Connect the HMI to the SSW06 Cables with lenths of 1; 2; 3 and 5 m. The x on the cable name represents the cable lenht. CONNECTING CABLES FOR REMOTE INTERFACE CAB-HMI SSW06- X Fieldbus Communication Boards They enable data exchane and control of the SSW06 in communication networks. KITS FOR FIELDBUS COMMUNICATION NETWORKS Profibus-DP KFB-PD DeviceNet KFB-DN Profibus-DP V1 KFB-PDPV1 Acyclic DeviceNet KFB-DD EtherNet/IP and Modbus/TCP KFB-ENIP It Enables the Connection of the SSW06 To a Modbus-RTU communication network in RS485 with alvanic isolation. RS485 COMMUNICATION KIT RS485 KRS SSW06 - Soft-Starter

11 Protection for Power Terminals Provides IP20 protection to the soft-starter power terminals. POWER TERMINAL PROTECTION KIT (for model rane 45 to 820 A) KIT IP20-M2 (45 A and 130 A) KIT IP20-M3 (170 A and 205 A) KIT IP20-M4 (255 A to 365 A) KIT IP20-M5 (412 A to 604 A) KIT IP20-M6 (670 A and 820 A) USB Kit Allows the connection of the SSW06 to a PC via USB. USB K-USB COMMUNICATION KIT Diital Input and Output Expansion Kit Six diital inputs and six diital outputs with alvanic isolation to be used with the SoftPLC. DIGITAL K-IOE IO EXPANSION KIT External Current Acquisition Kit If you use an external bypass contactor, it is necessary to install the external current transformers. K-ECA EXTERNAL CURRENT ACQUISITION KIT (for model rane 255 A to 1,400 A) SSW06 - Soft-Starter 11

12 Flexible and Compact Supply line input Electronic board coatin class 3C2 or class 3C3 as optional item, accordin to IEC , ensures reater protection for installations in environments with corrosive chemical aents. Fieldbus communication network modules for: Profibus-DP DeviceNet (optional) PTC input for the motor Six isolated and prorammable diital inputs Motor supply output Two prorammable analo outputs 12 SSW06 - Soft-Starter

13 Detachable human-machine interface with double display (LCD + LEDs), multiple lanuaes and copy function 32-bit, RISC type, hihperformance microcontroller Three prorammable diital relay outputs RS485 Modbus-RTU Serial Interface (optional) RS232 Modbus-RTU Serial Interface Control cable passae and conduit connection system Electronics protection fuse SSW06 - Soft-Starter 13

14 Dimensions and Weihts w D H Model SSW Width W (mm) Heiht H (mm) Depth D (mm) Weiht (k) SSW SSW SSW SSW SSW SSW06.85 SSW SSW SSW SSW SSW SSW SSW SSW SSW SSW SSW SSW SSW SSW , Frame Mountin D B C A Model A (mm) B (mm) C (mm) D (mm) Fixin screw SSW SSW SSW SSW SSW M5 1 SSW SSW SSW SSW SSW M5 M6 2 3 SSW SSW SSW SSW M6 4 SSW SSW SSW SSW M6 M8 5 6 SSW M8 7 SSW SSW , M8 8 Frame 14 SSW06 - Soft-Starter

15 Clearances for Ventilation A Model A (mm) B (mm) C (mm) D (mm) Frame SSW SSW SSW B B SSW SSW SSW SSW C Air flow output SSW SSW SSW SSW SSW SSW SSW SSW D SSW SSW SSW SSW Air flow input SSW SSW Frame07 Frame08 Frame05 Frame06 Frame04 Frame03 Frame02 Frame01 SSW06 - Soft-Starter 15

16 Technical Data Power (220 to 575) V ac (-15% to +10%) or (187 to 632) V ac (575 to 690) V ac (-15% to +10%) or (489 to 759) V ac Control (110 to 230) V ac (-15% to +10%) or (94 to 253) V ac Model rane 255 to 820 A: 115 V ac (104 to 127) V ac / 230 V ac (207 to 253) V ac Power supply Model 950 A: Fan 115 V ac (103.5 to 122) V ac / 230 V ac (207 to 243.8) V ac Model rane 1,100 to 1,400 A: 230 V ac (207 to 243.8) V ac Frequency (50 to 60) Hz (±10%), or (45 to 66) Hz Deree of protection Metallic cabinet IP00 Electronic board Standard Electronic board coatin class 3C2, accordin to IEC coatin Optional Electronic board extra coatin class 3C3, accordin to IEC Control method Voltae variation on the load (three-phase induction motor) CPU 32-bit RISC microcontroller Control Control types Voltae ramp Current limit Current limit ramp Pump control Torque control 1, 2 or 3 points Startin duty 2) Normal 300% (3 x Inom.) for 30s for 3-cable connection and for 25 s for 6-cable connection Inputs Diital 5 prorammable isolated inputs 24 V dc 1 prorammable isolated input 24 V dc (for the motor thermistor-ptc) Relay 3 prorammable outputs 250 V / 2 A: (02 x NO) + (01 x NO + NC - Defect) Outputs 1 prorammable output (10 bits) 0 V dc Analo 1 prorammable output (10 bits) 0 20 ma or ma Overvoltae Undervoltae Voltae imbalance Undercurrent Overcurrent Current imbalance Overload in the output (motor) - i²t Overtemperature in the thyristors/heatsink Overtemperature in the motor/ptc Reverse phase sequence External defect Defect in the bypass open 1) Defect in bypass closed 1) Overcurrent in the bypass 1) Undercurrent before the bypass 1) Phase loss in the power supply Safety Protections Phase loss in the output (motor) Fault in the thyristor Error in the CPU (Watchdo) Prorammin error Serial communication error Self-dianosis error HMI-SSW06-LCD communication error Startin time too lon Fieldbus communication error Undervoltae in the electronics Frequency out of rane Ground fault Motor misconnection Undertorque Overtorque Underpower Overpower Functions/resources Standard Built-in (detachable) human-machine interface with double display LED + LCD (HMI-SSW06-LCD) Password to enable prorammin HMI-SSW06-LCD lanuae selection: Portuuese, Enlish, Spanish, German Control type selection: voltae ramp, current limit Current limit ramp, pump control Torque control Selection of local/remote operation Fault self-dianosis Guided start-up accordin to control type Standard or motor inside delta connection All the protections and functions also available in the motor inside delta connection Pump Control Function (protection aainst Water Hammer in pumps) Copy function (Soft-starter HMI or HMI Soft-starter) Bypass incorporated to the soft-starter (model rane 10 to 820 A) RS232 serial interface with built-in Modbus-RTU, RS485 optional Input for the motor PTC Fault self-dianosis and auto-reset Reset to factory settin or user's settin Special resources: hour meter, wattmeter Prorammable overvoltae, undervoltae and voltae imbalance between phases Prorammable overcurrent, undercurrent and current imbalance between phases 16 SSW06 - Soft-Starter

17 Functions/resources Human-machine interface (HMI-SSW06-LCD) Environment conditions Finishin Compliance/standards Standard (V) Optional items Command Supervision (readin) Temperature Humidity Altitude Color Safety Low voltae EMC UL (USA) / cul (Canada) CE (Europe) IRAM (Arentina) C-Tick (Australia) Gost Undercurrent and overcurrent before the bypass Prorammable overtorque and undertorque Prorammable overpower and underpower Prorammable rated line voltae Fully prorammable voltae ramp Prorammable current limit Prorammable current ramp Prorammable pump control Totally flexible torque control Prorammable thermal memory auto-reset Prorammable protection thermal class (motor overload) from class 5 to class 45 Chane of speed direction JOG in frequency function in both speed directions Reverse brakin Optimal brakin without contactor DC brakin Built-in SoftPLC Frame for remote HMI Cable for the remote interconnection of the HMI: 1, 2, 3 and 5 m RS485 communication kit Profibus-DP and Profibus-DP V1 communication kit Acyclic DeviceNet communication kit EtherNet/IP and Modbus/TCP communication kit IP20 kit for model rane 45 A to 820 A Start, stop/reset and parameter settin (prorammin of eneral functions) Increases and decreases parameters or their content Motor current (% I n of the Soft-Starter) Motor current (% I n of the motor) Motor current (A) Supply line frequency ( Hz) Supply line voltae ( V) Output voltae ( V) Motor torque (% I n of the motor) Active power supplied to the load (kw) Apparent power supplied to the load (kva) Soft-starter state Diital and analo input and output state Cos (ϕ) of the load ( ) Hours enerized Hours enabled Enery consumption in kwh Analo output value SoftPLC state Backup of the last 6 errors with state, current and voltae dianosis Soft-starter software version Motor thermal protection ( ) Current indication in each R-S-T phase Indication of R-S/S-T/T-R line voltae State of the Fieldbus communication board Start dianosis Dianosis of operation in full duty 0 to 55 ºC (model rane 85 to 820 A) without rated current deratin 0 to 40 ºC (model rane 950 to 1,400 A) without rated current deratin % non-condensin (0 1,000 m): normal operatin conditions at rated current 1,000 4,000 m): with output current deratin of 1%/100 m above of 1,000 m Cover: extreme matte ray Cabinet: extreme matte blue UL 508 Standard Industrial Control Equipment EN ; LVD 2006/95/EC Standard - Low Voltae Directive EMC directive 2004 / 108 / EEC - Industrial Environment Underwriters Laboratories Inc. USA Certified by EPCOS Instituto Arentino de Normalización Australian Communications Authority (Russia) Notes: 1) Model rane 10 to 820 A. 2) Startin duty: 10 starts/hour for model rane 10 A to 820 A. 5 starts/hour for model rane 950 A to 1,400 A. SSW06 - Soft-Starter 17

18 Specification Table Model (control: V) (fan: 110/220) 2) 3) SSW06 soft-starter Inominal (A) Voltae (V) Standard connection (3 cables) Maximum applicable motor Inside delta connection (6 cables) Ta= C 4) Ta= C 4) Ta= C 4) cv kw cv kw Frame SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T2257 PSZ SSW T2257 PSZ SSW T2257 PSZ SSW T2257 PSZ SSW T2257 PSZ SSW T2257 PSZ SSW T2257 PSZ 1, SSW T2257 PSZ 1, , SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ , SSW T 2257 PSZ , SSW T 2257 PSZ 1, ,400 1,030 SSW T 2257 PSZ 1,400 1, ,750 1, SSW06 - Soft-Starter

19 Model (control: V) (fan: 110/220) 2) 3) Soft-starter SSW06 Inominal (A) Standard connection (3 cables) Maximum applicable motor Inside delta connection (6 cables) Voltae (V) Ta= C 4) Ta= C 4) Ta= C 4) HP kw HP kw Frame SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ , SSW T 2257 PSZ ,400 1,030 7 SSW T 2257 PSZ 1, ,600 1,175 SSW T 2257 PSZ 1,400 1, ,000 1,475 8 SSW T 2257 PSZ ,5 - - SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ SSW T 2257 PSZ , SSW T 2257 PSZ , SSW T 2257 PSZ ,550 1,140 6 SSW T 2257 PSZ 950 1, ,800 1,325 7 SSW T 2257 PSZ 1,100 1, ,100 1,550 SSW T 2257 PSZ 1,400 1,500 1,100 2,650 1,950 8 Notes: 1) The maximum powers of the motors in the table above were calculated based on WEG 2 to 4-pole motors. For motors with other polarities (e.., 6 and 8 poles), other voltaes (e.., 230, 400 and 460 V) and/or motors of other manufacturers, specify the softstarter by means of the motor nominal current. 2) For model 950 A, you must indicate if the fan voltae is 110 or 220 V ac. 3) For models 1,100 A and 1,400 A, the fan voltae is 220 V ac only. 4) Ambient temperature (You) = 0 55 ºC is only valid for A; for 950 A, 1,100 A and 1,400 A Ta = 0 40 ºC, (without rated current deratin). 5) Desined for exclusive industrial or professional use. SSW06 - Soft-Starter 19

20 Connection Types of the Soft-Starter to the Motor Standard (3 Cables) Motor Inside Delta (6 Cables) R S T R S T R S T F1 F2 F3 I Total F1 F2 F3 I Total F1 I Total F2 F3 U V W I SSW U V W I SSW I SSW U V W Motor in Y Motor in I Soft-Starter = I Total consumed I Soft-Starter = Motor inside delta connection I Total consumed 3 = 58% da I Total consumed (After the start) I Soft-Starter = I Total consumed 1.5 = 67% da I Total consumed (Durin the start) IMPORTANT: In the standard connection (3 cables) the motor can be connected in either Y (star) connection or in deltas connection. In the motor inside delta connection (6 cables), the motor can only be connected in delta. The table below shows the voltaes available for the standard motor types. Motor 6-cable connection 220 V - / 380 V-Y 220 V V - / 660 V-Y 380 V V - / 760 V-Y 440 V V V V - / 380 V- Y/ 440 V - / 760 V-Y 220 V V - For the same motor power, the motor inside delta connection (6 cables) enables a reduction of 42% in the soft-starter current in comparison to the standard connection (3 cables) The motor inside delta connection (6 cables) allows drivin a motor with a 73% hiher power than the standard connection (3 cables) The motor inside delta connection requires 6 connectin cables as far as the motor Durin the start, the motor current in relation to the soft-starter current may be up to 1.5 times hiher After the start at full voltae, the motor current in relation to the soft-starter current may be up to 1,73 times hiher 20 SSW06 - Soft-Starter

21 Selection Guide 1 SSW T P 6 O 7-8 SI Z 1 - WEG Soft-Starter SSW06 Family 2 - Soft-Starter Rated Output Current 0010 = 10 A = 130 A 0480 = 480 A 0016 = 16 A = 170 A 0604 = 604 A 0023 = 23 A 0205 = 205 A 0670 = 670 A 0030 = 30 A 0255 = 255 A 0820 = 820 A 0045 = 45 A 0312 = 312 A 0950 = 950 A 0060 = 60 A 0365 = 365 A 1,100 = 1,100 A 7 - Deree of Protection Blank Standard (see table of characteristics) 8 - Human-Machine Interface (HMI) Blank Standard (with LEDs + LCD HMI) SI Without HMI 9 - Special Hardware 0085 = 85 A 0412 = 412 A 1,400 = 1,400 A 3 - Soft-Starter Input Power Supply T Three-phase Blank H1 H2 Standard Ventilation 115 V (950 A) E..: SSW T 2257 P S Z Ventilation 230 V (model rane 950 A to 1,400 A) E..: SSW T 2257 P S H1 Z 4 - Power Supply 2,257 = rane ( V) 5,769 = rane ( V) 5 - Lanuae of the Product Manual P Portuuese E Enlish S Spanish 6 - Product Versions 10 - Coatin of the Electronic Boards Blank EC 11 - Special Software Blank S End of Code Coatin class 3C2, accordin to IEC Extra coatin class 3C3, accordin to IEC Standard Optional with special software version S Standard Blank Standard O With optional items Z Product final codin indicator diit Notes: 1) The communication kits are optional. 2) For model rane 950 A to 1,400 A, the ventilation voltae must be defined (H1 or H2). SSW06 - Soft-Starter 21

22 Global presence is essential, as much as understandin your needs. Global Presence With more than employees worldwide, WEG is one of the larest electric motors, electronic equipments and systems manufacturers. We are constantly expandin our portfolio of products and services with expertise and market knowlede. We create interated and customized solutions ranin from innovative products to complete after-sales service. WEG s know-how uarantees our SSW06 Soft-Starter is the riht choice for your application and business, assurin safety, efficiency and reliability. Availability is to have a lobal support network Partnership is to create solutions that suit your needs Competitive ede is to unite technoloy and innovation 22 SSW06 - Soft-Starter

23 Know More Hih performance and reliable products to improve your production process. Excelence is to provide a whole solution in industrial automation that improves our customers productivity. Visit: youtube.com/wevideos SSW06 - Soft-Starter 23

24 WEG Worldwide Operations ARGENTINA San Francisco - Cordoba Phone: info-ar@we.net COLOMBIA San Cayetano - Boota Phone: info-co@we.net MALAYSIA Shah Alam - Selanor Phone: info@wattdrive.com.my SINGAPORE Sinapore Phone: info-s@we.net Cordoba - Cordoba Phone: we-morbe@we.com.ar Buenos Aires Phone: ventas@pulverlux.com.ar AUSTRALIA Scoresby - Victoria Phone: info-au@we.net AUSTRIA Markt Piestin - Wiener Neustadt-Land Phone: watt@wattdrive.com Sabaneta - Antioquia Phone: info-co@we.net ECUADOR El Batan - Quito Phone: weecuador@we.net FRANCE Saint-Quentin-Fallavier - Isère Phone: info-fr@we.net GERMANY Türnich - Kerpen Phone: info-de@we.net MEXICO Huehuetoca - Mexico Phone: info-mx@we.net Tizayuca - Hidalo Phone: info-mx@we.net NETHERLANDS Oldenzaal - Overijssel Phone: info-nl@we.net PERU La Victoria - Lima Phone: info-pe@we.net Sinapore Phone: info-s@we.net SCANDINAVIA Mölnlycke - Sweden Phone: info-se@we.net UK Redditch - Worcestershire Phone: info-uk@we.net UNITED ARAB EMIRATES Jebel Ali - Dubai Phone: info-ae@we.net Vienna Phone: wtr@we.net BELGIUM Nivelles - Belium Phone: info-be@we.net BRAZIL Jarauá do Sul - Santa Catarina Phone: info-br@we.net CHILE La Reina - Santiao Phone: info-cl@we.net CHINA Nanton - Jiansu Phone: info-cn@we.net Chanzhou - Jiansu Phone: info-cn@we.net Ruao - Jiansu Phone: zhuhua@we.net Balinen - Baden-Württember Phone: info@we-antriebe.de Homber (Efze) - Hesse Phone: info@akh-antriebstechnik.de GHANA Accra Phone: hana@zestwe.com INDIA Banalore - Karnataka Phone: info-in@we.net Hosur - Tamil Nadu Phone: info-in@we.net ITALY Cinisello Balsamo - Milano Phone: info-it@we.net JAPAN Yokohama - Kanaawa Phone: info-jp@we.net PORTUGAL Maia - Porto Phone: info-pt@we.net RUSSIA and CIS Saint Petersbur Phone: sales-wes@we.net SOUTH AFRICA Johannesbur Phone: +27 (0) info@zestwe.com Cape Town Phone: +27 (0) entsets@zestwe.com Heidelber Phone: +27 (0) /4/5 wta@zestwe.com SPAIN Coslada - Madrid Phone: info-es@we.net Valencia Phone: info@autrial.es USA Duluth - Georia Phone: info-us@we.net Bluffton - Indiana Phone: info-us@we.net Minneapolis - Minnesota Phone: info-us@we.net Washinton - Missouri Phone: wewill@we.net VENEZUELA Valencia - Carabobo Phone: info-ve@we.net For those countries where there is not a WEG own operation, find our local distributor at WEG Group - Automation Business Unit Jarauá do Sul - SC - Brazil Phone: automacao@we.net Cod: Rev: 00 Date (m/y): 01/2018 The values shown are subject to chane without prior notice.