BUTBRO WELDING PRODUCTS

Transcription

1 1190 ORBIT Lightweight Welding and Cutting Blowpipe A new superbly constructed welding & cutting blowpipe designed with safety in mind and engineered from highest quality materials to complement the operator in production or light gauge maintenance welding & cutting. The shank is common to both welding and cutting heads, the same quick, positive and leak-free means of attachment being used for both. The shank is manufactured from a solid drilled aluminium forging thus avoiding necessity of internal tubes and giving added safety. Welding The shank can be used with either lightweight swaged nozzles or D.H. solid copper tips + brass neck according to the operators preference, enabling precise flame control and up to mm (5/16 ) welding capacity in steel. Cutting The newly designed lightweight cutting attachment uses the nozzle mix principle and is thus highly resistant to backfire and flashback. Although of a lightweight design, it is engineered from solid brass casting and silver soldered tubes to provide and extremely robust construction. Using Orbit A-FN type nozzles and fuel gas the orbit has a cutting capacity of over 0mm. BUTBRO torches and nozzles conform to BS EN ISO 517 Orbit L/W Welding Outfit Consisting of:- ORBIT Shank & Mixer, L/W Nozzles Sizes 1,,,5,7,,1,5, Hose Check Valves Outfit, Spanner, Data Card, Plastic Carrying Case Orbit D.H. Welding Outfit Consisting of:- ORBIT Shank & Mixer, Threaded D.H. Neck, D.H. Tips Sizes 1,,,5,7,,1, 1,5, Hose Check Valves, Outfit Spanner, Data Card, Plastic Carrying Case Orbit Combined Welding & Cutting Outfit Consisting of:- ORBIT Shank & Mixer & Cutting Attachment, L/W Nozzles Sizes,5,7,,1, 1,5, /6 A-FN Type Cutting Nozzle, A-SFN Type Sheet Metal Cutting Nozzle, Nozzle Cleaning Outfit, Outfit Spanner, Data Card, Plastic Carrying Case Orbit Complete Combined Welding & Cutting Outfit Consisting of:- ORBIT Shank & Mixer & Cutting Attachment, Single Stage, 1 Gauge Regulator, Single Stage, 1 Gauge Regulator, 5 Metres /16 Bore Twin Line Fitted Hose, L/W Nozzles Sizes,5,7,,1, /6 A-FN Type Cutting Nozzle, A-SFN Type Sheet Metal Cutting Nozzle, Sunfire Spark lighter, Nozzle Cleaner Outfit, Outfit Spanner, Combination Spanner, Goggles, Data Card, Plastic Carrying Case Orbit LW W & C Blowpipe HOSE CONNECTION - 1/ BSP (Other threads available on request) 1 Welding Shank WELDING CAPACITY - mm 1 Orbit Cutting Attachment CUTTING CAPACITY - 0mm 5 Orbit Welding Mixer WELDING NOZZLES - Lightweight Swaged 6 Orbit threaded D.H. Neck Nozzles Sizes 1-5 D.H Solid Copper Tips Sizes 1-5 CUTTING NOZZLES - ORBIT A-FN Cutting Nozzles ORBIT A-SFN Sheet Metal Nozzles 1.11

2 Steelmaster With forward mounted valves and cutting lever for additional safety and flat handle. Standard Models: Length 1 (60mm), 7 (700mm), 6 (900mm) Head Angles 90 o, 75 o, 10 o Fuel : or Propane Universal With rear mounted valves and cutting lever and round handle. Standard Models: Length 1 (60mm), 7 (700mm), 6 (900mm) Head Angle 90 o, 75 o, 10 o Fuel : or Propane 7090 Steelmaster 1 90 o cutter 7091 Steelmaster 1 75 o cutter 709 Steelmaster 1 10 o cutter 090 Universal 1 90 o cutter Hose Connections - / (Other threads available on request) Cutting capacity - mm (1 ) Nozzles - ANM () Cutting Nozzles PNM (Propane) Cutting Nozzles ASNM Sheet Metal Cutting Nozzles AGNM Gouging Nozzles ARCNM Rivet Cutting Nozzles PH5 Heating Nozzles Cutting Torch Accessories Double Roller Guide ( ) Steady and guide your torch over large plates and forgings. Fits all nozzle- mix cutters using ANM/ PNM type nozzles. Fixed by clamping around nozzle thus accommodating either 75 o or 90 o torch heads. Spade Guide ( ) For straight, accurate cutting of plates. Fixing is same as roller guide. Large Circle Cutting Attachment ( ) Cut accurate circles with this versatile attachment. A rotary head ensures free running either clockwise or anti-clockwise, together with a square radius bar which prevents twisting. It is adjustable to cut circles from 60mm ( 1 / ) up to 5mm (17 ) Dia. Two models are available with either a male headnut (Butbro Steelmaster, Butbro MK / etc.) or a female headnut (MK equipment). Small Circle Cutting Attachment ( ) For cutting smaller diameter circles, clamps to tubes of cutter or cutting attachment. Three models are available to suit various tube configurations. 1.1

3 MK /A Combined Welding and Cutting Torch The BUTBRO MK /A is a high pressure, sturdily constructed and well balanced welding and cutting torch. Each component (shank, mixer, cutting attachment) is inter-changeable with other leading makes of type equipment. It has front mounted colour coded control valves, employing stainless valve spindles fitted with both O ring and nylon seals; providing fine adjustment and leak- free conditions, using extremely moderate gas pressures. The shanks is common to both welding and cutting heads, the same quick positive positioning and leak-free means of attachment being used for both. BUTBRO torches and nozzles conform to BS EN ISO 517. Butbro MK /A Combined Welding & Cutting Outfit Cosisting of:- MK /A Shank, Mixer & Cutting Attachment Type Swaged Welding Nozzles Sizes,5,7,,1,1,5, 1/16 ANM Cutting Nozzle /6 ANM Cutting Nozzles, Nozzle Cleaner Outfit, Headnut Spanner, Data Card, Plastic Carrying Case Butbro MK /A Combined Welding & Cutting Outfit Consisting of:- MK /A Shank, Mixer & Cutting Attachment, Single Stage, gauge Regulator, Single Stage, Gauge Regulator, 5 Metres 1/ Bore Twin Line Fitted Hose, Type Swaged Welding Nozzles Sizes,5,7,1, 1/16 ANM Cutting Nozzle, Sunfire Spark lighter, Nozzle Cleaner Outfit, Combination Spanner, Spindle Key, Headnut Spanner, Goggles, Data Card, Plastic Carrying Case Welding and Heating Designed for welding work from 1 swg to cover 1 thickness using type swaged nozzles sizes 1-90 liters. The mixer seats on serrated toothed faces allowing the operator a selection of positive nozzle positioning through 60º. Also can be used for heating, with either acetylene or propane heating nozzles, together with a heating neck. Cutting The cutting head is nozzle mixing, enabling the operator to use either acetylene or propane fuel gases by fitting the appropriate nozzle. A range of ANM and PNM nozzles are available for clean efficient cutting of material thickness from sheet metal to 50mm ( ) using both acetylene, and propane fuel. Its versatility also allows gouging, flame cleaning etc., to be supplied to customer s requirements. Propane Super Heating Using a propane super heating mixer and or stainless steel super heating neck and intense heat output of up to 600,000 Btu/H is obtained. Ideal for heating castings and similar large articles. MK /A Combined Welding & Cutting Torch 77 MK /A Shank 77 MK /A Welding Mixer 76 MK /A Cutting Attachment MK /A Super Heating Mixer 6666 MK Brass Heating Neck ( ) 6777 MK Brass Heating Neck ( ) 7666 MK Stainless Steel Neck ( ) 7777 MK Stainless Steel Neck ( ) 7 MK Stainless Steel Neck (0 ) Hose Connections - / (Other threads available on request) Welding capacity - 5mm Cutting capacity - 50mm Welding Nozzles - Type & Swaged Welding Nozzles Sizes 1-90 Cutting Nozzles - ANM () Cutting Nozzles PNM (Propane) Cutting Nozzles ASNM Sheet Metal Nozzles AGNM Gouging Nozzles ARCNM Rivet Cutting Nozzles Heating Nozzles - AHT () Heating Nozzles PHT (Propane) Heating Nozzles Super Heating - Super Heating Nozzles Nozzles (Propane) Sizes 1H-5H 1.1

4 Welding - Butbro Orbit & MK /A Torches Mild Steel Thickness mm in swg / 5/ /16 1/ 5/16 / 1/ /0 7/0 Nozzle size bar PSI Operating pressure bar PSI Welding, Cutting & Heating Data consumption l/h ft³/h l/h ft³/h Flame Cleaning- Butbro MK /A Torches fuel gas Nozzle Type 50mm flat 0mm flat 150mm flat Fuel gas pressure bar PSI pressure bar PSI Fuel consumption consumption l/h ft³/h l/h ft³/h Super Heating - Propane - Butbro MK /A & Super Heating Torches The flame size and heat output of these nozzles varies considerable with the pressure settings used. Two typical alternatives are given for each size of nozzle. Nozzle Propane pres pres Type bar PSI bar PSI 1H H H H 5H Propane cons l/h ft³/h Heat output cons (app.) bar PSI W Btu/h Heating - - Butbro MK /A Torch (AHT Nozzles) Nozzle Type A-HT5 A-HT50 A-HT0 gas pres pres bar PSI bar PSI Heating - Propane - Butbro MK /A Torch (PHT Nozzles) Nozzle Propane Fuel gas pres pres cons Type bar PSI bar PSI l/h ft³/h P-HT P-HT Fuel gas cons cons Heat output (app.) l/h ft³/h l/h ft³/h W Btu/h Heat output cons (app.) l/h ft³/h W Btu/h Cutting - - Butbro Ortbit Torch Material Thickness Nozzle mm in 1/ 1/ / 1 size S/M 1/ /6 1/16 1/16 Operating pressure bar PSI bar PSI consumption Cutting Heating l/h ft³/h l/h ft³/h l/h ft³/h Cutting - - Butbro MK /A & 1/90 Cutters (ANM Nozzles) Material Thickness mm in Sheet 6 1/ 1 1/ Operating pressure consumption Cutting Heating Nozzle size bar PSI bar PSI l/h ft³/h l/h ft³/h l/h ft³/h Asnm 1/ /6 1/ /16 1/16 5/6 /./.5 5/ /. 50/ /. 5/ /5.5 5/ / 1/ 1/ Gouging - Butbro MK /A & 1/90 Cutters (AGNM Nozzles) Material Thickness mm 11 1 in 5/16 7/16 1/ Nozzle size Operating pressure bar PSI bar PSI 7 7 consumption Cutting Heating l/h ft³/h l/h ft³/h l/h ft³/h Cutting - Propane - Butbro MK /A & 1/90 Cutters (PNM Nozzles) Material Thickness mm in 1/ 1/ Nozzle size 1/ /6 1/16 1/16 1/16 5/6 / 1/ 1/ Operating pressure bar PSI bar PSI 6 Approx Cutting Speeds mm.m in.m Approx Cutting Speeds mm/m in/m Approx Cutting Speeds mm/m in/m Approx Cutting Speeds l/h ft³/h l/h ft³/h l/h ft³/h mm/m in/m consumption Cutting Heating 1. Data is for guidance only and may vary with operating conditions, materials, etc.. pressure are shown in BAR-1 bar= 1kg cm² 1 PSI= bar.. consumption in LITRES PER HOUR (l/h). 1.1

5 MK /A Combined Welding And Cutting Torch AHT AGNM PNM Super Heating (Propane) Welding Heating Cutting ANM or 7 for size

6 mm mm 9mm mm mm Cutting Nozzles For use with Butbro and all other leading makes of nozzle- mix equipment ANME- Long Pattern 6 Heating Holes- Long Pattern mm Long. Use Fuel Range Size 51-6mm 1/ mm / mm 1/ mm 5/ mm / mm 7/ mm 1/ PNME- Long Pattern 9 Spline or 1 Spline Inner - Long Pattern mm Long. Use Propane Fuel Range Size 61-6mm 1/ mm / mm 1/ mm 5/ mm / mm 7/ mm 1/ AGNM Gouging Nozzles 9mm Long. Use Fuel Range Size mm Width x -9mm Depth 1-1/ mm Width x 6-11mm Depth 19 - / mm Width x 9-1mm Depth 5-1/16 ASNM Sheet Metal Nozzles mm Long. Use Fuel Range Size mm Sheet Metal 0. AFN Type (Orbit) Nozzles Use Fuel Range Size 0- mm Sheet Metal ASFN 11-6 mm 1/ mm / mm 1/

7 Welding and Heating Nozzles Lightweight Swaged Copper Tube Nozzles For use on Butbro Orbit torch 1/ x 6 TPI thread. Range Size 601 to 1.0mm mm - 1.5mm mm -.0mm 605.0mm -.5mm mm -.0mm 7 Range Size 6.0mm -.0mm 61.0mm - 5.0mm mm - 6.0mm mm -.0mm 5 D. H. Type Solid Copper Tips For use on Butbro Orbit torch 5/16 x 5 TPI thread. Use in conjuction with DH neck Range Size 61 to 1.0mm mm - 1.5mm 6 1.5mm -.0mm 65.0mm -.5mm mm -.0mm 7 Range Size 6.0mm -.0mm 61.0mm - 5.0mm mm - 6.0mm mm -.0mm 5 Type ///5 Swaged Cooper Tube Nozzles For use on Butbro Type ///5 Welding Torch 7/16 x 7 TPI Thread (Sizes 1-90 Butbro Type & ) 1/6 x 7 TPI Thread (Sizes 5-90 using Heavy Duty Mixer) Range Size 6501 to 1.0mm mm - 1.5mm mm -.0mm mm -.5mm mm -.0mm mm -.0mm 651.0mm - 5.0mm 1 Range Size mm - 6.0mm mm -.0mm mm -.0mm mm - 1.0mm mm mm mm - 5.0mm over 5.0mm 90 Butbro Super Heating Nozzles For use on type //5 blowpipe in conjunction with heavy duty mixer and necks 7666 or Can also be used with NM 50/ Steelmaster in conjunction with super heating adaptor use propane fuel gas. Size ,000 Btu/h 1H 799,000-1,000 Btu/h H 799 1,000-61,000 Btu/h H Size 799 6,000-06,000 Btu/h H ,000-61,000 Btu/h 5H 7996 Nozzle Adaptor for NM Cutters Butbro AHT/PHT Heating Nozzles For use on Butbro Type and and torches with brass heating neck. Use Fuel with AHT type nozzles. Use Propane Fuel with PHT type nozzles. Size 5 HEATING TIP AHT5 50 HEATING TIP AHT50 HEATING TIP AHT0 Size 6 HEATING TIP PHT 660 HEATING TIP PHT60 Butbro PH5/PH6 Heating Nozzles For use on Butbro Steelmaster and Universal and other NM cutters (PH5) MS cutter (PH6). Use Propane Fuel Size 705 HEATING Nozzle PH5 706 HEATING Nozzle PH6 707 Spare Insert for PH5/6 706 Spare Headnut for PH5/6 1.17

8 Single-stage Regulators BUTBRO single stage regulators are precision built to latest BS EN ISO 50 standards to provide maximum accuracy and safety. Encapsulated control valves, 6mm pattern pressure gauges, captive pressure adjusting screw, permanently engraved identification on body to maintain ID even if labels are removed. Models available: gauge, Gaugeless, 1 gauge,. Flo-Gauge. Pre-set Regulators are available for most common gases in either side or bottom entry with inlet threads suitable for any local cylinder connection standards. Regulators are also available with NEVOC type fittings. Regulators - Side Entry Gauges Argon CO* * for CO regulators use heaters above l/m. CO Heaters 1 Regulators - Bottom Entry Propane Argon Argon Argon Gauges Inlet Outlet (bar) Inlet Fitted between the cylinder and the regulator, preventing freezing inside the regulator Outlet (bar) ~15 LPM 0 ~15 LPM Inlet Outlet Flow (form) G 5/ (BS) G 5/ (BS) CGA 50 G 5/ LH (BS) CGA G 5/ (BS) 0.60x1TPI (BS) G 5/ (BS) G 5/ (BS) G 5/ (BS) G 5/ LH (BS) G 5/ LH (BS) G 5/ LH (BS) G 5/ (BS) G 5/ (BS) G 5/ (BS) 9/16 x 1 G / LH 9/16 x 1 LH G / LH G / LH G / LH m /h Inlet Outlet Flow (form) m /h LPM 15 LPM 550 Butbro CO Heater 1 Volt 5501 Butbro CO Heater 0 Volt Referigeration Regulator This range of regulators is specifically designed to meet the needs of heating, ventilation and air conditioning (HVAC) trades, for pirge and leak test applications. Available in three pressure variants, the regulators are supplied with JIC fitting outlets Type. RS 00 RS 600 RS 750 Inlet (bar) Outlet 1 5 Inlet G 5/ G 5/ G 5/ Outlet (form) W 11 x 1,5 W 11 x 1,5 W 11 x 1,5 1.1

9 76151 Multi-stage regulators for cylinder and manifold mounting GCE multi-stage regulator are designed to provide accurate, fluctuation free delivery for precision applications such as machine cutting or laboratory use. The first stage reduces the inlet pressure by over 90% and the large second stage diaphragm ensures accurate delivery. GCE multistage regulators are precision built to latest BS EN ISO 50 and BS EN 791 standards to provide maximum accuracy and safety. These regulators have the additional feature of being able to pipe away gases from the relief valve port, and comply with the stringent requirements of BS EN 791. Features: Forged brass body. Safety Valve. 50mm dia dual scale safety pressure gauges. Captive pressure adjusting screw. Regulators are available for most common gases in either side or bottom entry with inlet threads suitable for any local cylinder connection standards. Regulators are also available with NEVOC type fittings. Regulators - Bottom Entry Gauges Inlet Outlet (bar) Inlet Outlet Flow (form) (m³/h) Hydrogen Hydrogen Nitrous oxide G 5/ G 5/ G 5/ LH G 5/ G 5/ G 5/ G 5/ LH G 5/ LH BS1 G / LH LH LH Regulators - Side Entry Gauges Inlet Outlet (bar) Inlet Outlet Flow (form) (m³/h) CO CO Helium Helium For CO regulators use heaters above 0 Vmin G 5/ G 5/ G 5/ LH G 5/ 0,60 x 1 TPI 0,60 x 1 TPI G 5/ G 5/ G / LH Line Regulators Linemaster Maximum inlet pressure bar. Inlet 1/ NPT male, outlet G/ RH or LH male cone. For a new installation both a Linemaster regulator and Linemaster Outlet Point are required. Outlet Pressure Flammable (LH) Flammable (LH) Flammable (LH) 1.5 bar.0 bar.0 bar 1.5 bar.0 bar.0 bar 1.5 bar 1.19

10 S series S series - heavy duty single regulators of brass construction with stainless steel diaphragms. Typical applications are system charging and testing. Range -170 bar delivery pressure. Order No` Type Entry Inlet Outlet Flow (m³/h) S 00 S 1500 S 500 S 1500 S 500 bottom bottom bottom bottom bottom bar bar bar bar bar bar 0 bar 170 bar 0 bar 170 bar M600 series M600 series - improved delivery pressure control is achieved from two stage regulation. Typical applications are those left unattended for periods of time such as cable pressurisation, chemical and laboratory. Range up to 1 bar delivery pressure. Order No` Type Entry Inlet Outlet Flow (m³/h) M 600 M 600 M 600 M 600 M 600 CO Flammable side bottom bottom side bottom 00 bar bar bar bar bar 1 bar 1 bar 1 bar 1 bar 1 bar 0 0 OR1 series OR1 series - offering some of the highest flows in the Butbro range through the use of a special monel tied valve, these are intended for cylinder and pipeline applications. The G5/ inlet adaptor can be removed to reveal a 1 BSP flat seat female fitting. Range up to 1 bar delivery pressure. Order No Type Entry Inlet pressure Outlet pressure Flow HR 1 OR 1 Hydrogen rear rear bar bar 1 bar 1 bar 50 m /h m /h S150 0L series S1500L series - this pipeline regulator is ideal for tank systems, rear entry to suit panel or line mounting. The largest outlet configuration is necessary to give high flow from a relatively low inlet pressure source. Max inlet bar and delivery up to bar. Order No Type Entry Inlet pressure Outlet pressure Flow 7596 S 150 OL rear bar bar 0 m /h 1.0

11 Flow Meters A precision flow meter in brass finish providing extremely accurate flow setting. Available in models : 0-15 Liters/Min and 0- Liters/Min Economizer Gauges 0-15 LPM 0 - LPM Considerable savings in gas costs can be achieved by the use of a gas economizer in production welding and brazing. The torch is held on the hooked arm when not in use which shuts off gas supply to the torch. When unhooked the torch can be immediately re- ignited from the pilot light without having to re-adjust the valves. / BSP Connections Economizer Spark lighters SUNFIRE TYPE with cup to collect gases, ideal for site use, screw on flints. TRIPLE TYPE cup to collect gases, clip-on triple flint replacement. PISTOL TYPE with reliable action, sliver finish, single replacement flint Sunfire Spark Lighter Triple Flint Spark Lighter Pistol Spark Lighter Spare Flints for Sunfire Spark Lighter Spare Flints for Pistol Spark Lighter Triple Flint Renewals Spanners and Keys COMBINATION SPANNERS for 5/ BSP nuts and / BSP nuts with combined cylinder key. SPINDLE KEY for oxygen and acetylene cylinders, hardened, drop forged. ORBIT OUTFIT HEADNUT SPANNER for headnut of Steelmaster, BUTBRO Type and most other NM torches x ways Combination Spanner Outfit Head Nut Spanner Cylinder Spindle Key Way Combination Spanner Way Combination Spanner Safety Curtains / Welding Screens A portable free standing screen enabling the welding area to be enclosed thus protecting the surrounding workspace from the effects of glare and spatter. Constructed from green translucent PVC. This material complies with EN 159 and is both UV stabilized and self extinguishing. Overall size - 6 x 6 (Curtain: 5 9 x 5 ) Size Colour Portable welding screen 6 x 6 Green 1.1

12 Superguard FR50 Reset Flashback Arrestors A regulator mounted safety device suitable for all welding and cutting operations, fully complying with EN7, this lift to reset unit incorporates the following features: FA Sintered flame arresting element NV Non return valve to prevent reverse flow of gases PV Pressure trip device, activated by pressure wave accompanying a flashback TV Thermal trip device, activated by heat to permanently cut off the gas supply SI Status indicator shows green when unit is ready for use. In the event of a flashback the item can be reset by lifting and releasing the bonnet Fuel gas Fuel Working pressure bar bar bar bar Inlet connection G / LH G 9/16 RH G 9/16 LH Outlet connection G / LH G 9/16 RH G 9/16 LH Slimguard 99 Flashback Arrestors The new Slimguard 99 for regulator mounting has been redesigned incorporating an improved sintered filter and thermal trip device. Complies with EN7 FA Sintered flame arresting element NV Non return valve to prevent reverse flow of gases TV Thermal trip device, activated by heat to permanently cut off the gas supply Fuel gas Fuel Working pressure bar bar bar bar Inlet connection G / LH G 9/16 RH G 9/16 LH Outlet connection G / LH G 9/16 RH G 9/16 LH FR6 High Flow Pipeline Flashback Arrestors Designed for use with acetylene manifolds up to 1.5 bar, this line mounted arrestor is fitted with BSP11/ inlet and outlet and mm pipe stubs. Flow Rate 50 M/H maximum. The unit incorporates the following features: FA SINTERED FLASH ARRESTOR element to quench a flashback. 165 Flameguard Torch Flashback Arrestors A lightweight torch flashback arrestor specially designed for torch fitting. It incorporates an aluminum body and is manufactured to our own unique design without using soldered or bonded joints. The unit incorporates the following features:- 1) Sintered Flash Arrestor element to quench a flashback. ) Non-Return Valve to prevent reverse flow of gases. ) Filter gauze to prevent foreign matter entering unit. R.H L.H / BSP RH or LH for mm Hose / BSP RH or LH for mm Hose / BSP RH or LH for 6mm Hose 1/ BSP RH or LH for 6mm Hose 1/ BSP RH or LH for 5mm Hose 1.

13 Hose Check Valves (Patent No. 0761) Hose check valves prevent the reverse flow of gases beyond the torch inlets. Butbro hose check valves are manufactured to our own approved design and the unique method of assembly eliminates the use of soldered or bonded joints. They are suitable to use with,, Propane or natural gas and operate effectively on either nozzle-mix or injector type torches or regulator. R.H O Clips L.H Butbro Hose Check Valve / BSP RH or LH Nut for mm Hose Butbro Hose Check Valve / BSP RH or LH Nut for mm Hose Butbro Hose Check Valve / BSP RH or LH Nut for 6mm Hose Butbro Hose Check Valve 1/ BSP RH or LH Nut for 6mm Hose A quick permanent method for fastening hose connections. Zinc plated mild steel, other sizes available up to / Diameter. Use size 9/16 for /16-1/ bore hose. Use size 5/ for 5/16 - / bore hose. Use size / for / bore ply hose. O Clip Pincers Quality forged steel pincers specially designed for fixing O clips / O Clip (11 to 1mm Dia:) For 5mm Bore Hose 9/16 O Clip (1 to 15mm Dia:) For 6mm Bore Hose 5/ O Clip (15 to 1mm Dia:) For mm Bore Hose / O Clip (17 to 0mm Dia:) For mm Bore Hose 7/ O Clip (0 to mm Dia:) For mm Ply Bore Hose O Clip Pincers for fixing above clips 1.

14 Manifolds - couplers, adaptors and fittings Type - RH Adaptor - 90º cylinder adaptor Adaptor - straight cylinder adaptor Adaptor - branch adaptor Adaptor - branch adaptor Adaptor - G 1/ MALE x G / loose nut Adaptor - soldering / loose nut for 15mm Adaptor 1/NPTM x G/M Blanking plug Coupler - 1/NPT Equal coupler RH Line valve 1/ turn butterfly operated Line valve 1/ turn butterfly operated Line valve 1/ turn lever operated Shut off valve- handwheel Rating (Bar) Inlet Connection G 5/ M G 5/ M G 5/ M G 5/ M G 1/ M RH / Outlet Connection G 5/ F G 5/ F G 5/ F G 5/ F F 15 mm tube 1/NPTM G/M G 5/ M - 1/ NPT M 1/ NPT M M M 1/ NPT F 1/ NPT F M M W1. x 1/1RH W1. x 1/1LH Type - LH Adaptor - 90º cylinder adaptor Adaptor - straight cylinder adaptor Adaptor - branch adaptor Adaptor - branch adaptor Adaptor - G 1/ MALE x G / LH loose nut Adaptor 1/NPTM x G/M LH Adaptor - soldering / loose nut for 15mm Blanking plug Line valve 1/ turn butterfly operated Line valve 1/ turn lever operated Rating (Bar) Inlet Connection G5/ M LH G5/ M LH G5/ M LH G5/ M LH G1/ M RH 1/NPT M / LH G5/ M LH G/ M LH G/ M LH Outlet Connection G 5/ F LH G 5/ F LH G 5/ F LH G 5/ F LH F LH M LH 15 mm tube - M LH M LH Pipeline adaptors / NPT x / H/D loose nut RH / NPT x / RH / NPT x / H/D loose nut LH 110 1/ NPT x / LH 1.

15 Fine Adjustment Valves Inlet Connection RH MALE LH MALE 1/ NPT MALE 1/ NPT MALE Outlet Connection RH MALE LH MALE RH MALE LH MALE Fine Adjustment Valves with Swivel Nut Swivel Nut RH MALE LH MALE Outlet Connection RH MALE LH MALE Twin Outlet Valves with Swivel Nut ( Y Valves) These allow two blowpipes to be used from one regulator outlet Swivel Nut RH LH Outlet Connection RH MALE LH MALE Twin Outlet Valves with Swivel Nut ( Y Valves) RH LH Y piece with swivel nut fitted with nuts and mm nipples T piece with RH/LH nuts and mm nipples Y piece with swivel nut LH fitted with nuts and mm nipples T piece with LH nuts and mm nipples Hose Connector (RH) (LH) Hose connector / BSP Male x 1/ Tail Hose connector / BSP Male x 5/16 Tail Hose connector / BSP Male x / Tail Hose connector / BSP Male x 1/ Tail 1.5

16 Hose Tailpieces Hose Splicers Hose Inner Diameter 5-6 mm (1/ -/16 ) TAPER STEM 6 mm (1/ ) 6 mm (1/ ) mm (5/16 ) Hose Inner Diameter 6 mm (1/ ) mm (5/16 ) mm (/ ) Suitable For Unit LH and RH G 1/ LH and RH LH and RH LH and RH Hose Connection Nuts Hose Couplers Hose Adaptors Type- RH G 1/ RH RH G 9/16 RH Type- RH G 1/ equal x G1/ unequal equal G 1/ equal G /1 equal G1 equal Type- LH G 1/ LH LH G 9/16 LH Type- LH G 1/ LH x G 1/ unequal equal G 1/ equal G / equal G 1 equal Type- RH G 1/ FEMALE x MALE FEMALE x 1/ MALE FEMALE x 1/ MALE 9/16 x 1 TPI FEMALE x G 1/ MALE 9/16 x 1 TPI FEMALE x MALE 9/16 x 1 TPI FEMALE x MALE 9/16 x 1 TPI MALE x FEMALE G/ MALE x G 1/ FEMALE Type- LH G 1/ FEMALE x MALE FEMALE x 1/ MALE FEMALE x 1/ MALE 9/16 x 1 TPI FEMALE x G 1/ MALE 9/16 x 1 TPI FEMALE x MALE 9/16 x 1 TPI FEMALE x MALE 9/16 x 1 TPI MALE x FEMALE G/ MALE x G 1/ FEMALE Type Bent Solid Bent Type Bent Solid Bent 1.6