Prvi korak pri izbiri tesnil

Transcription

1 procesna oprema Prvi korak pri izbiri tesnil KLINGER

2 Prvi korak pri izbiri tesnil This survey should not be used as the sole means for gasket selection. To assist you in gasket selection, we have devised a tried and tested method designed to guide you step by step to the right gasket for your needs. Kemikalije Chemicals g aseous and liquid Voda in para Water and steam Drugi mediji Special applications up to 400 C up to 50 C over 600 C up to 00 C up to 50 C Oxygen Gas supply Food industrie Acids Caustics KLINGERtopline KLINGERtop-chem-000 KLINGERtop-chem-00 KLINGERtop-chem-005 KLINGERtop-chem-006 KLINGERtop-sil-ML KLINGERtop-graph-000 relatively suited well suited very well suited BAM tested/ TA-Luft -certification/ Fire Safe/ TA-Luft -certification/ TA-Luft -certification/ BAM tested/ TA-Luft -certification/ BAM tested/ TA-Luft -certification/ WRC in preparation BAM tested/ TA-Luft -certification/

3 Prvi korak pri izbiri tesnil Drugi mediji Special applications Caustics Food industrie Acids Voda in para Wuater and steam u Gas supply Oxygen p to 50 C Kemikalije Chemicals g aseous and liquid p to 00 C over 600 C up to 50 C up to 400 C KLINGERSIL C C-44 C-400/ C-44 C-404 C-4400 C-440 C-4500/ carbon fibre reinforced C-44 C-4408/ -4409/ -448/ -449 C-4509/ carbon fibre reinforced C-406 C-607/ C-67 C-0 relatively suited well suited very well suited / WRC permit (only C-44) ÖVGW permit BAM tested/ HTB tested/ ÖVGW permit/ TA-Luft -certification/ Germ. Lloyd BAM tested/ HTB tested/ Germ. Lloyd/ Fire Safe/ TA-Luft / WRC permit BAM tested/ ÖVGW permit/ Fire Safe/ TA-Luft -certification/ Germ. Lloyd DVGW permit/ BAM tested/ Fire Safe/ TA-Luft -certification/ Germ. Lloyd Germ. Lloyd (only C-4409)/ Expanded metal reinforced for higher thermal and mechanical demands Germ. Lloyd/ Expanded metal reinforced for highest thermal and mechanical demands High compressibility, for low stresses / Controlled swell in oils TA-Luft -certification/ Germ. Lloyd/ Specifically designed for use with strong acids

4 Faktor tesnil KLINGER KLINGERSIL Type KLINGERSIL C-400/ C-44 KLINGERSIL C-4400 KLINGERSIL C-4408/ C-4409/ C-448/ C-449 KLINGERSIL C-440 KLINGERSIL C-4500 KLINGERSIL C-4509 KLINGERSIL C-0 thickness σ VO 5 C >40 > DIN 90/DIN 9 DIN 505 ASTM σ Vu 0, σ BO (7..) 5 C C C C C k. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D. x b D K O xk D (N/) x b D x b D x b D x b D x b D x b D 8 x b D 8 x b D x b D x b D x b D x b D x b D x b D 8 x b D 8 x b D x b D x b D x b D m factor y Stress KLINGERtop-chem and top-graph Type KLINGERtop-chem 000 KLINGERtop-chem 00 KLINGERtop-chem 005 KLINGERtop-graph 000 thickness σ VO 5 C >0 >0 >60 DIN 90/DIN 9 DIN 505 ASTM σ Vu 0, σ BO (7..) 5 C C C C C * k. x b D. x b D. x b D. x b D. x b v K O xk D (N/) 5 x b D 5 x b D 5 x b D x b D x b D m factor y Stress * 00 C The evaluation of these characteristic datas are based on the rules of DIN 90. The use of this values will not guarantee the performance of the gasket. Application conditions not in the control of the gasket material manufacturer can influence the operation of the gasket. A deducation of liability claims of any nature is therefore not possible. As further investigations are continuosely carried out we reserve the right of appropriate updates. The design factors m and y according to the ASME Code are based on a maximum leakage rate of ml/min. approx. 0. mg/sec x m measured according to DIN 90 at different gas pressures and different gasket stresses. The DIN 505 and the y and m concept itself now being questioned as a valid design tool. Subject to technical alterations. Status: January 005 Certified according to DIN EN ISO 900:000

5 Technical fax service +86 (0) 4 45 For improved reliability and security the technical mail service is an addition to the KLINGER-expert calculation program. In most cases, the answers to the following three groups of questions are sufficient to ensure the right gasket is selected. Please complete the questionnaire in full. Our reply will often be on your desk in 4 hours. Complete, print, fax to: Rich. Klinger Dichtungstechnik GmbH & Co KG, Austria Fax ++4 (0) 5/ In other countries, please refer to the local Klinger address. Operating fluid Medium Flange with bolts Flange: Gasket Dimension acc. to Material DIN ANSI or indicate the compressed Pressure [bar] Temperature [ C] Dimension acc. to DIN/ANSI dimensions D a [] D i [] Temperature variations during service DN PN Gasket thickness [] free choice Drawing included conditioned by design, since Bolts: Type Number Size Material/grade Coents Da D i Company Contact Street City or town Phone Fax

6 Oblikovali smo zanesljivo in preizkušeno metodo, ki vas bo po korakih vodila do tesnila primernega vašim potrebam. Applications overview: The gasket characteristics compared with the criteria to be met in typical application.. Product documentation: A separate data sheet is supplied for each gasket in our range. The pt diagrams are an invaluable aid to selecting the gasket most suitable for a particular application.. Data on chemical resistance: This section indicates the resistance of the individual Klinger gaskets to over 00 chemicals in coon use. 4. Technical information by Fax: Let us have the details of your particular gasket requirements and you will receive a prompt reply, in some cases within 4 hours. 5. Sealing calculations on your PC: For the experienced specialist we have developed a powerful program which will answer all your questions on gasket construction, design and maintenance. We supply the software with on-line help. 6. Ideally you should run your own tests: We will supply the materials you need to carry out tests under your own operating conditions. 7. On-sit advice: With particularly difficult problems we shall be glad to advice you on-site. We can supply products adapted from our existing range or custom-formulated products. Powerful sealing calculation with online help on CD-ROM Certified according to DIN EN ISO 900:000 procesna oprema Tbilisijska 57, Ljubljana Telefon: +86(0) (0) 4-74 Telefaks: +86(0) info@trimad.si