CB15 CB15S CB15 with Hot Blending Lid

Transcription

1 OPEN OPEN Unit Information 15.0 Amps HP 3 OPEN 2 1 CBL10 Hot Blending Lid (optional) Year Limited Motor Warranty 2 Year Limited Warranty Electronic Membrane Keypad Slow Start Blending Mechanism One Gallon Blender with Hot Blending Lid Marked for Deletion DB (on 8/28/2012) with BB150DW (on 4/1/2005) Calico Label NSF NSF Seal Container with Blending Assembly Container Complete with Lid Container Complete with Stainless Steel Lid Blending Assembly (on units before 9/24/2004) Different From new Assembly (limited quantities available) Washer O Ring Bearing Cap (changed after 2/24/2006) Blending Assembly (replaces & ) Graphic by: Sandra A. Montysko Revised May 18, 2016 Approved 5/19/16 Page 1 of DB- (on units before 10/9/2006)

2 Name Plate /Don Name Plate /Calico Base Unit with Hot Blending Lid Marked for Deletion DB (on 8/28/2012) with BB150DW (on 4/1/2005) Calico Label POWER ON/OFF STOP HEAVY DUTY BLENDER LOW MED HIGH PULSE Brush & Spring Assembly (2 required on units after 4/7/2016) Brush Cap (2 required on units after 4/7/2016) Page 2 of 5 Revised May 18, 2016

3 DB G N Illustration # Part # Description Hot Blending Outer Lid Hot Blending Outer Lid Gasket Hot Blending Baffle Cup Cap Nut DB Flat Washer Blade "O" Ring Bearing Cap Small "V" Ring Bearing Holder Washer Bearing Spacer Spring Washer Retaining Ring Large "V" Ring Drive Shaft Key (changed after 6/18/2004) Cover Insert (on,, DB, units after 9/27/2006) Outer Lid (on,, DB, units after 9/27/2006) Stopper (used with plastic lid) Plastic Outer Lid (obsolete) Plastic Lid Gasket (on units before 10/9/2006) Latch Wire (3 required) Bracket Assembly-spot welded to container (3 required) Double Handle Container 27 Complete Blending Assembly (changed after 2/24/2006) Container Support Gasket Container Support (container base changed after 8/12/2002) Lock Nut Coupling with Magnet Ring (on units after 8/20/2013) Coupling Jar Pad Top Housing (changed 10/25/2010) Revised May 18, 2016 Page 3 of 5

4 DB G Illustration # Part # Control Panel (on units after 8/20/2013) Control Panel Rear Control Panel (on units after 8/20/2013) Screw (4 required) Control Panel Baffle (on units after 8/20/2013) Washer (4 required on units after 4/7/2016) Washer (4 required on units after 3/12/2003) (8 required for use with ) Screw (4 required on units after 4/7/2016) Screw (4 required on units after 3/12/2003) Screw (4 required holds mounting plate to motor) Screw (4 required holds mounting plate & motor to top housing) Motor Modified Grosohopp ECM Motor with MTP (on units after 9/27/2013) Motor with Sensor (on units after 8/20/2013) ECM Motor (on units after 3/13/2003) Motor (no longer available) Baffle Baffle Screw (6 required) Screen Cable Tie (on units after 9/10/2013) (5 required) Cord Set (on units after 8/20/2013) Cord Set (on units after 1/17/2003) Cord Set Strain Relief Bottom Housing Washer (4 required) Screw (4 required) Ground Washer (on units after 10//12/2009) Washer Ground Screw (on units after 10//12/2009) Screw Foot (4 required) Washer (4 required) Screw (4 required) Hall Effect Sensor (on units after 8/20/2013) Screw (2 required on units after 8/20/2013) Page 4 of 5 Revised May 18, 2016 N DB Description

5 DB G N DB Parts No Longer Used POWER ON/OFF STOP HEAVY DUTY BLENDER LOW MED HIGH PULSE Crimp Connector (on units between 3/14/2003 thru 8/20/2013) Lead & Fuse Assembly (on units between 3/14/2003 thru 8/20/2013) Motor Plate (on units before 3/13/2003) Control Module Panel (on units before 9/3/2013) Brush & Spring Assembly (2 required on units before 4/14/2016)) Brush Cap (2 required on units before 4/14/2016) Motor Hall Effect Sensor Red Green Wiring Diagram (on units after 8/20/2013) Green/Yellow Brown ACL ACN M- M+ Yellow Brown or Green or White Motor Wiring Diagram Red Revised May 18, 2016 Page 5 of 5