Standard Kerb & Channel

Transcription

1 Standard Kerb & Channel B Code KC A Mould No C Stringline 280 To Face Edges 140 from back A 600 from front B From prep C Machine can pass as close as 80mm from obstacles to back of kerb.

2 Kerb only (STD) A B Code KO Mould No Stringline 400 To Face 230 Edges 250 from back A 400 from front B 175 Note : This mould can be done in 3 finished heights 200mm 250mm 300mm

3 450 Dish Drain Code DISHF B Mould No 3 A C Stringline 325 To centre 450 Edges 100 from Line A 550 from Line B 170 from Prep C

4 Mountable Kerb and Channel (STD) Code MKC Mould No Stringline 320 To Face Edges 170 front up from prep C 522

5 300 Kerb only ( Insert into mould 20 ) 290 Code WKO Mould No 5 Stringline 500 To Face 220 Edges from back from front 300

6 600 Dish Drain Code DISHS Mould No 6 Stringline 420 To Face Edges 120 from back A 127 from front B 170 from prep C 607

7 Standard Kerb & Channel ( Reverse ) 140 Code KC Mould No Stringline 280 To Face 460

8 Xing Kerb & Channel Code XKC Mould No Stringline 320 To Face Edges 140 from back 585 from front 445

9 Kasel Kerb ( Bus Stop ) Code KASEL Mould No

10 Mountable Kerb only Code MKO Mould No Stringline 500 To Face Edges 95 top below line 155 top above prep 308 Note: Can add skids for different heights

11 300 High Kerb & Channel 135 Code 300HKC Mould No Stringline 280 To Face Edges 140 from back 580 from front 440

12 Mountable Kerb and Channel Code MKC Mould No

13 300 Wide Kerb & Channel 290 Code 300WKC Mould No 13 Stringline 500 To Face Edges from back from front 587 Prep at 300mm deep from top of kerb!!

14 205 Mountable Kerb only Code 205MKO Mould No Stringline To Face 203

15 Mountable Kerb and Channel Code MKC Mould No

16 600 Flat Code 600F Mould No Stringline 125 To edge 600

17 Kerb & Cha Prep - 250mm from top of kerb height Code KC Mould No Stringline To Face 225 TOK to invert 120

18 Small Kerb only (Insert) Code SKO Mould No Stringline To Face 157

19 Mountable Kerb only ( Insert into mould 20 ) Code 190MKO Mould No Stringline 420 To Face Edges from back from front 230 This mould can have 100mm skids added to give 300mm on back face

20 325 Dish Prep - 180mm from top edge of Dish height 325DISH Mould No 20 35mm 150mm 325mm

21 Mountable Kerb only Code MKO Mould No

22 No Good Kerb & Channel ( old outside ) 145 Outside Code KC Mould No Stringline To Face 458

23 Mountable Kerb Island Prep - 250mm from top of kerb height Outside Code MKC Mould No

24 Low Kerb & Channel Prep - 180mm from top of kerb height Outside Code LKC Mould No

25 Mountable Kerb Prep - 210mm from top of kerb height Code MKC Mould No

26 Mountable Kerb and Channel Prep - 250mm from top of kerb height Outside Code MKC Mould No

27 Mountable Kerb and Channel Prep - 290mm from top of kerb height Outside Code MKC Mould No PREP to 290 deep

28 RP Kerb and Channel Prep - 220mm from top of kerb height Code RPKC Mould No R12 R20 Stringline 280 To Face R

29 RP Kerb Only Code RPKO Mould No 29 Stringline 280 To Face 135 Clearances and normal settings for the kerb only machine ( also see notes for RP Machine on Prep Notes Page ) Kerbing machine Stringline pin 180 min dist 60mm Normal 140 Normal 280 Normal 660 Kerb shape This height can be : Prep 200mm 250mm 300mm 350mm We add skids to bottom of machine to get deeper kerb,then after 250mm we also change to a different ram. 175 As you can see the normal distance to the stringline can be changed if needed to get very close to objects. Normal distances shown are what we setup the stringline to. On right angled corners its good to have a 1.3m over run so we can get the machine right past the corner so then we can butt up to that and carry on the other side of the corner.

30 RP Kerb Only Code RPKO Mould No 30 & Stringline 280 To Face Note : This mould can be done in 3 finished heights 200mm Mould mm Mould mm Mould 31

31 RP 200 Kerb Only Code RP200KO Mould No Stringline 350mm To Face Note : This mould can be done in 3 finished heights 200mm Mould mm Mould mm Mould 34

32 RP MKO Code RPMKO Mould No 35 65mm 134mm Stringline 340 To Face 210mm 30mm Note : This mould can be done in 3 finished heights 150mm 200mm 250mm This mould is good for laying straight onto road surface for traffic islands

33 Code RPMKO Mould No

34 Wanganui Kerb & Channel ( Insert goes into top corner of old KC ) A B Code KC 140 Mould No C Stringline 280 To Face Edges 140 from back A to stringline from front B to stringline 150 From prep C Machine can pass as close as 80mm from obstacles to back of kerb.

35 RP DISH Halfpipe Prep - 200mm from top of kerb height Code RPDISH Mould No Stringline To Face 340

36 RP Garden Edge Insert into mould 40 Code RPGE Mould No R R15 10 Stringline To Face

37 RP Kerb & Edge Code RPKE Mould No R12 Stringline To Face