Extreme Automatics Pressure Release Transbrake 2004R 54E10.1

Size: px
Start display at page:

Download "Extreme Automatics Pressure Release Transbrake 2004R 54E10.1"

Transcription

1 Extreme Automatics Pressure Release Transbrake 2004R 54E10.1 The Electric Trans brake will work with any 2004R VB or shift kit. The rd transmission being used must be dual feed 3. The Electric Trans brake only st works from the manual 1 gear position. **** This Kit is to be installed by those with moderate mechanical skills and should not be installed by a novice builder.***** Included in the kit (1) Electric Pressure Release Solenoid (1) Aluminum Manifold (1) Steel Retaining plate (1) O-ring (1) Aluminum Base Plate (1) Allen Head screw (2) 6mm-20 Cap Screws (2) 6mm-25 Cap Screws (1) 6mm-30 Cap Screw (3) 1/4-20 Cap Screws (1) 1/8" NPT Hex Nipple (1) 1/8" NPT Female 90deg (1) Straight Compression 1/8" NPT to 3/8 Tube (1) 90 deg Compression 1/8 NPT to 3/8 tube (1) 7" 3/8" Nylon hose (1) Single pole case bulkhead fitting *** The instructions are written for installation with transmission in vehicle. If trans is on a bench for a rebuild. Look to last page for transbrake tune up. These modifications are not necessary but will maximize the setup and release of the transbrake. ***

2 Transbrake Installation Instructions 1. Drain and Remove Transmission Pan 2. Remove Valvebody 1-2 accumulator housing, 1-2 steel channel plate, spacer plate. 3. Discard 1-2 accumulator housing, Steel channel plate, 3-4 accumulator piston and pin. These parts will no longer be used. 4. Now we have disassembled the transmission. It should look like the picture below. 5. Check the spacer plate for the following holes. Most shift kits will use a factory plate. When a factory plate is used then place the checkballs at the locations in the Fig 1. If an aftermarket plate is used compare required holes with figure 2.

3 6. Install Case Gasket, Spacer Plate, Valvebody gasket and Aluminum Channel Plate. Install the Channel Plate using the 2 short 6mm bolts and the mid length 6mm bolts. Torque to 100 inch lb. ( Fig 3)

4 Valvebody Modifications 7. Remove the lo overrun valve and grind small end until over all length is Re-install spring and drop extra check ball from valvebody into the bore so it s placed inside of the spring. Re-install the lo over run valve. The object is to block the valve from movement. rd 9. If the 3 gear lock up pressure switch is to be used. You will need to run a 1/8" NPT tap deep into the threads to allow the male to female 90deg NPT fitting to be installed flush to allow installation of the pressure switch. (See example) 10. There is 1 area on the valve body that interfere with the TB base plate. Clearance as needed. 11. Machining the Valvebody for the transbrake Manifold and retaining plate. This work needs to be done in a vertical mill. Most machine shops can

5 provide this service. Follow the instructions closely. Failure to do so can destroy your valvebody. 12. Install two long bolts threw the bolt holes in fig. #4. The bolts should protrude past the face of the valvebody approximately ½". These bolts will now become the alignment bolt for setting up the valvebody on the mill rd table. These bolt holes are on line with the 3 gear passage casting. See Fig #4

6 13. Place the valvebody directly on the mill table with the machined face of the valvebody on the mill table. Place the 2 bolts threw the holes shown in the Fig #4. Now move VB so the bolts go threw the VB and protrude into one of the mill table channels. Move the VB so the bolts both hit squarely on one side of the mill table channel. Now clamp the VB in place. With the Vb rd clamped you can now machine the VB and stay parallel with the 3 gear casting channel. 14. Touch off the face of the Valvebody as listed in photo. When you get the depth then start cutting left or right. Cut the VB back until a measurement from edge of bolt hole to edge of machined surface is.555 to.560. Machine past the bolt hone and past the casting number on the VB. See example in photo. 15. Now its time to surface the top of the VB. Lift end mill off of the new face.490 to.500. (The technique I use is to take the manifold and place in the stop of the mill then lock the head. This will lift the end mill up the exact amount.)

7 16. Cut across the top of the VB to make nice flat surface for the retention plate. Make sure to surface both bolt holes. What you are doing now is making a flat surface for the retention plate to mount and preload the manifold from 0 to.010. This also bring the bolt height back to the factory height so the new plate does not interfere with the filter. Remove the 2-3 shiftvalve and bushing. Drill the Exhaust Hole to.250 See Picture below. 17. With the Vb machined and clearance we are ready to install the VB on the transmission. Checkballs go in the following locations on all shift kits.

8 18. Install the Valvebody. Install all bolts but leave out the bolts that fasten the retaining plate. 19. Install 1/8 90deg fitting in the manifold. Tighten and leave at a slight angle upward away from the VB. 20. Install o-ring in the manifold. Leave the retaining plate attached with the bolt snug. Use Grease to hold o-ring in place.

9 21. Install manifold and retaining plate assembly to valvebody. Tighten bolts to 100 inlb. With the plate bolted try to wiggle the manifold. If the manifold is tight then tighten the bolt that fasten the manifold to the retaining plate. If the manifold is loose use a little shim stock between retaining plate and manifold to add preload. Good preload is 0 to Install the 1/8 NPT hex nipple, female 90 deg fitting in base plate and tighten. Leave at slight angle for solenoid installation. See photo. 23. Install Nylon Hose. Be careful not to kink the hose. A good length is 6-7/8. The hose is supplied in 7" length. 24. Install the Solenoid. Attach the ground wide to one of the 1/4-20 mounting bolts. Turn the fitting back into position close to solenoid.

10 25. Install case connector or Bulkhead fitting. When hooking up the power wire from solenoid be sure to route the wire away from the manual valve. You can see in the pick if the positive wire is not routed properly it can hangup in the manual valve. 26. The transbrake install is complete. You can now install filter and pan. The factory pan may need some slight dinging to clear the solenoid. Adjust as needed. 27. The transbrake install is now complete. When the transmission is full of fluid and up to operating temperature we are ready to test the brake. st Place the transmission in manual 1. Depress the transbrake button and load the engine. The transbrake is not a toy. The converter will build heat rapidly when you are using the transbrake. Limit times to 4 or 5 seconds. I do not recommend stall testing but if you do stall test. Allow 3 or 4 minutes of idle time to cool down the transmission before you shut off the engine. To test transbrake speed you must load the engine and release.

11 Transbrake tune up If the transmission is on the bench for rebuild. Here are a few tips to maximize setup and release of the transbrake. 1) Drill fittings to maximum diameter. Leave enough material for secure attachment of the fitting. 2) Enlarge the direct feed hole in the center support. 3) Remove the tube support in the brass fittings 4) Install stiffer return springs in direct drum. 5) Open direct clutch clearance to.010 per clutch or a maximum of.070 6) Remove L/R wave plate and use flat L/R steel. 7) Make sure to use a.296 reverse boost valve or larger 8) Do Not use a relay in the transbrake wiring. It will only slow the brake. If you must use a relay use a Solid State Relay or Digital Relay. The tranbrake solenoid pulls 7 amps. Good micro switch works best.

Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd

Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd TCI 221500 Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd This Valve Body will neutralize at shut-down by putting shifter In 2nd gear position This Kit Contains: (1) Turbo

More information

TRANSMISSION PARTS Instructions. Solenoid Regulator Valve Retainer Shim. Main Pressure Regulator Valve

TRANSMISSION PARTS Instructions. Solenoid Regulator Valve Retainer Shim. Main Pressure Regulator Valve TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-AODE NOTE: This kit is fully compatible with '91 '95 only. Identified by alignment pins 13mm heads. This kit will not work on '96 Later units.

More information

HIPSTER S TURBO 350 TRANSBRAKE

HIPSTER S TURBO 350 TRANSBRAKE HIPSTER S TURBO 350 TRANSBRAKE THIS IS THE QUICKEST AND MOST CONSISTENT T350 BRAKE AVAILABLE. AS WITH ANY NEW PRODUCT THERE ARE CERTAIN STEPS THAT MUST BE FOLLOWED TO INSURE YOUR SUCCESS WITH IT. PLEASE

More information

CHEETAH PRO SERIES TRANZ BRAKE VALVE BODY (Not for Street Use) Part #24941

CHEETAH PRO SERIES TRANZ BRAKE VALVE BODY (Not for Street Use) Part #24941 1535 Owens Road, Jacksonville, FL 32218 Phone 904-741-4850 * Fax 904-741-4853 www.turboaction.com CHEETAH PRO SERIES TRANZ BRAKE VALVE BODY (Not for Street Use) Part #24941 Reverse Shift Pattern (PRN123)

More information

AODE ( 96 & LATER) SC-AODE-1. Transmission Reconditioning Kit FULL COMPATIBILITY IMPORTANT VALVE BODY PARTS REASSEMBLY PARTS

AODE ( 96 & LATER) SC-AODE-1. Transmission Reconditioning Kit FULL COMPATIBILITY IMPORTANT VALVE BODY PARTS REASSEMBLY PARTS AODE ( 96 & LATER) Transmission Reconditioning Kit FULL COMPATIBILITY SC-AODE-1 Full compatibility with 1996 and later units. Identified by alignment pins with 10mm head and.173" pin diameter. IMPORTANT

More information

2244 West McDowell Road Phoenix, AZ RACE (fax) INSTALLATION INSTRUCTIONS FOR

2244 West McDowell Road Phoenix, AZ RACE (fax)   INSTALLATION INSTRUCTIONS FOR 2244 West McDowell Road Phoenix, AZ 85009 602-257-9591 1-800-274-RACE 602-340-8429 (fax) www.hughesperformance.com INSTALLATION INSTRUCTIONS FOR HP2215 TH400 3-SPEED TRANSBRAKE VALVE BODY KIT Please read

More information

Installation Instructions for TCI Turbo 700R TCI Turbo 700R

Installation Instructions for TCI Turbo 700R TCI Turbo 700R Installation Instructions for TCI 378805 Turbo 700R4 1982-1984 TCI 378905 Turbo 700R4 1985-1993 KIT INTRODUCTION Read all instructions first to familiarize yourself with the parts and procedures. Work

More information

Installation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.

Installation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation. Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware

More information

TRANSMISSION PARTS Instructions

TRANSMISSION PARTS Instructions TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-4T65E GM 4T65-E Valve Body Parts Boost Valve Kit 84754-30K Patent No. 6,832,632 TCC Apply Valve Kit 84754-43K Patent No. 7,100,753 TCC Regulated

More information

INSTALLATION INSTRUCTIONS LOKAR COLUMN SHIFT LINKAGE

INSTALLATION INSTRUCTIONS LOKAR COLUMN SHIFT LINKAGE INSTALLATION INSTRUCTIONS LOKAR COLUMN SHIFT LINKAGE Part No. ACA-1807 (Ford AOD) STOP! PLEASE READ ALL INSTALLATION INSTRUCTIONS BEFORE BEGINNING INSTALLATION. CALL LOKAR FOR ANY QUESTIONS OR UNCERTAINTIES

More information

PART # 4VB/FPFMTB Forward Pattern Full Manual Transbrake Valve Body with Engine Braking and Safe Neutral

PART # 4VB/FPFMTB Forward Pattern Full Manual Transbrake Valve Body with Engine Braking and Safe Neutral PART # 4VB/FPFMTB Forward Pattern Full Manual Transbrake Valve Body with Engine Braking and Safe Neutral NOTE: This product should be installed by a professional transmission mechanic who is fluent with

More information

HIPSTER'S ALUMINUM POWERGLIDE TRANSBRAKE (P/N: 12748A) CAUTION

HIPSTER'S ALUMINUM POWERGLIDE TRANSBRAKE (P/N: 12748A) CAUTION W140N10145 Fond Du Lac Ave. Germantown, WI 53022 Phone: (262) 251-7777 Email: info@autotransdesign.com www.autotransdesign.com HIPSTER'S ALUMINUM POWERGLIDE TRANSBRAKE (P/N: 12748A) CAUTION Please read

More information

PART # 4VB/RPFMTB Reverse Pattern Full Manual Transbrake Valve Body Assembly

PART # 4VB/RPFMTB Reverse Pattern Full Manual Transbrake Valve Body Assembly PART # 4VB/RPFMTB Reverse Pattern Full Manual Transbrake Valve Body Assembly Extensive research and development was performed during the inception of this product and has continued throughout its production.

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTALLATION GUIDE Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

Instruction Manual Includes:

Instruction Manual Includes: Instruction Manual Includes: Page 1: HydraHorse Installation for Basic 2- Horse System Part I: Tank, pump, and electrical supply Page 6: Page 9: Part II: Page Bowls, Brackets, Pipes and Fittings Installing

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTRUCTION BOOKLET Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side 2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and

More information

TCI E4OD/4R100 Valve Body Performance Improver Kit

TCI E4OD/4R100 Valve Body Performance Improver Kit 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TCI 496500 E4OD/4R100 Valve Body Performance Improver Kit TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com

More information

TCI Ford C-6 TransBrake Valve Body Shift Pattern: Park, Reverse, Neutral, First, Second, Third

TCI Ford C-6 TransBrake Valve Body Shift Pattern: Park, Reverse, Neutral, First, Second, Third 1 INSTRUCTIONS TCI 421500 Ford C-6 TransBrake Valve Body Shift Pattern: Park, Reverse, Neutral, First, Second, Third Thank you for choosing TCI products; we are proud to be your manufacturer of choice.

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

CHEETAH E-SHIFT Pro Series Valve Body (Positively Not For Street Use) Fits Torqueflite 727 & (Non Lock-Up)

CHEETAH E-SHIFT Pro Series Valve Body (Positively Not For Street Use) Fits Torqueflite 727 & (Non Lock-Up) 1535 Owens Road, Jacksonville, FL 32218 - (904)741-4850 - FAX (904)741-4853 www.turboaction.com CHEETAH E-SHIFT Pro Series Valve Body (Positively Not For Street Use) Fits Torqueflite 727 & 904 1966-90

More information

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case LoMax 205 CASE & 3:1 GEAR SET Part No. 2800 Instruction Rev: 2007.08.16 Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case Kit Components: 1. (1) 42x25

More information

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND DIAMETER VENTED ROTOR

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND DIAMETER VENTED ROTOR ASSEMBLY INSTRUCTIONS FOR SUPERLITE BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND 1.88 DIAMETER VENTED ROTOR 197-199 CAMARO, DISC/DRUM SPINDLE 197-1974 NOVA, DISC/DRUM SPINDLE 194-19 CHEVY II,

More information

Stage4 Installation Guide STAGE 4 TRANSMISSION KIT INSTALLATION GUIDE Allison LB7/ LLY only for 5 speed trasmissions

Stage4 Installation Guide STAGE 4 TRANSMISSION KIT INSTALLATION GUIDE Allison LB7/ LLY only for 5 speed trasmissions STAGE 4 TRANSMISSION KIT INSTALLATION GUIDE 2001-2005 Allison LB7/ LLY only for 5 speed trasmissions DISCLAIMER OF LIABILITY This is a performance product which can be used with increased horsepower above

More information

3 WRX/STI TURBO INLET HOSE

3 WRX/STI TURBO INLET HOSE 3 WRX/STI TURBO INLET HOSE Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance

More information

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT PART NUMBER SC-46-47RHE-OS INSTALLATION GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Sure Cure kit contents.

More information

Part # Mopar LX Level 1 Air Suspension System

Part # Mopar LX Level 1 Air Suspension System Part # 13040199 05-14 Mopar LX Level 1 Air Suspension System Front Components: 1 1304409 Front RQ ShockWave Kit for Stock Lower Arms Rear Components: 1 13044099 Rear CoolRide Kit 1 13040709 RQ Series Rear

More information

Return to Instruction Sheet index. Installation Instructions For C-4 70 and Later, Except 70 Falcon

Return to Instruction Sheet index. Installation Instructions For C-4 70 and Later, Except 70 Falcon Page 1 of 8 Return to Instruction Sheet index TCI 260100 Trans-Scat Automatic Transmission Installation Instructions For C-4 70 and Later, Except 70 Falcon TCI 260100 Kit Contains: Qty. Description One

More information

HP7482X POWERGLIDE TRANSBRAKE KIT

HP7482X POWERGLIDE TRANSBRAKE KIT INSTALLATION INSTRUCTIONS FOR: HP7482X POWERGLIDE TRANSBRAKE KIT Please read all instructions carefully before beginning installation! Hughes Performance 2244 West McDowell Road Phoenix, Arizona 85009

More information

46RE, 46RH, 47RE, 47RH ZIP KIT

46RE, 46RH, 47RE, 47RH ZIP KIT 46RE, 46RH, 47RE, 47RH ZIP KIT PART NUMBER 46-47RHE-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. installation Diagram 7 1 Separator

More information

TCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve.

TCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve. TCI 221100 Turbo 400 Full Manual Valve Body Shift Pattern: Park Reverse Neutral First Second Third This Kit Contains: (1) Turbo 400 Full Manual Valve Body (1) Separator Plate & Gaskets (1) Pressure Regulator

More information

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for install Jack Jack

More information

Air Compressor/Water Pump III - Making the Steam Valves

Air Compressor/Water Pump III - Making the Steam Valves Page 1 of 14 Air Compressor/Water Pump Part III Making the Steam Valves Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 1/09/04 Last Revised: 0 The cylinders pistons and water valves were completed

More information

Mercedes

Mercedes Mercedes 7.3 7.4 3 4 5 6 7 8 - Clutch K - Brake Band B 3 - Disc Brake B 3 4 - Wide Planet Pinion 5 - One-Way Clutch F 6 - Clutch K 7 - Brake Band B 8 - Narrow Planet Pinion Int. Band Fwd. Band Rev. Clutch

More information

Cable Shift Linkage Kit

Cable Shift Linkage Kit Cable Shift Linkage Kit INSTALLATION INSTRUCTIONS ididit column to GM Trans FOR PART NUMBER S: 2801000010, 2802000010 ididit Column to 350 Trans...Pg 1-4 ididit Column to 400 Trans...Pg 5-8 ididit Column

More information

Skirted GEN III - Technical Notes

Skirted GEN III - Technical Notes DART Skirted GEN III - Technical Notes Deck Height... 9.240-9.450 STD or Raised cam, 9.750 9.950 Raised cam only Bore... 4.000 & 4.125 Main Bearing Size... LS-1 (2.558" 2.559") Weight... 115lbs 4.125 and

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 970-973 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 0-905 WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

Installation Instructions: RB26 WET AND DRY SUMP ENGINE CRADLE

Installation Instructions: RB26 WET AND DRY SUMP ENGINE CRADLE Installation Instructions: RB26 WET AND DRY SUMP ENGINE CRADLE Congratulations on the purchase of your RB26 Platinum Racing Engine Cradle (PREC)! This PREC will assist in preventing block twist, block

More information

2244 West McDowell Road Phoenix, AZ RACE (fax)

2244 West McDowell Road Phoenix, AZ RACE (fax) 2244 West McDowell Road Phoenix, AZ 85009 602-257-9591 1-800-274-RACE 602-340-8429 (fax) www.hughesperformance.com HUGHES PERFORMANCE HP2215 VALVE BODY Installation Instructions 9/24/16 For over 45 years

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

Mercedes Clutch KS 5 - Brake BS 6 - Clutch K2

Mercedes Clutch KS 5 - Brake BS 6 - Clutch K2 965 Mercedes 7.5 1 9 8 6 3 7 5 1 - Brand Band B1 - Brake Band B 3 - Sprag Clutch F - Clutch KS 5 - Brake BS 6 - Clutch K 7 - Sprag Clutch F1 8 - Multi-Disc Clutch B3 9 - Clutch K1 Application Chart Lever

More information

1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and

1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and Installation Instructions for 603107 Valve Body Kit C-4 1970 & Later Tools Required Speed Handle or Ratchet 3/8 Drive 1/2 Socket 3/8 Drive 7/16 Socket 3/8 Drive 5/16 Socket 3/8 Drive Small Screwdriver

More information

Hughes Performance HP1218 Trans-brake Valve Body10/18/16

Hughes Performance HP1218 Trans-brake Valve Body10/18/16 2244 W McDowell Phoenix, AZ 85009 1-800-274-RACE FAX: 602-340-8429 602-257-959110/2/16 Hughes Performance HP1218 Trans-brake Valve Body10/18/16 For over 45 years our goal has been to provide racers and

More information

LB7/ LLY Allison 5 speed transmissions

LB7/ LLY Allison 5 speed transmissions PPEdiesel.com STAGE 4 TRANSMISSION KIT INSTALLATION GUIDE 2001-2005 LB7/ LLY Allison 5 speed transmissions Technical Support (714) 985-4825 Rev: 01/31/18 v7 DISCLAIMER OF LIABILITY This is a performance

More information

Your Steering Column Specialist

Your Steering Column Specialist Cable Shift Installation Instructions for: GM Column to GM Transmission GM Steering Column to: 350 Trans...Pg1 400 Trans...Pg5 700R4 & 4L60 Series Trans...Pg9 www.ididitinc.com ididit is... Your Steering

More information

PRXB EXHAUST BRAKE MAXIMUM EXHAUST FLOW DESIGN

PRXB EXHAUST BRAKE MAXIMUM EXHAUST FLOW DESIGN MAXIMUM EXHAUST FLOW DESIGN PRXB EXHAUST BRAKE C44072/C44073/C44074/C44075/C44076 APPLICATION: 994-2002 DODGE RAM TRUCKS W/5.9L CUMMINS DIESEL ENGINES WITH MANUAL & AUTOMATIC TRANSMISSIONS STOCK DODGE

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions ALL AMERICAN BILLET Front Drive System - Small Block Ford Installation Instructions Small Block Ford with AC & PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for

More information

TRANS-SCAT Installation Instructions for Ford AOD

TRANS-SCAT Installation Instructions for Ford AOD TCI 436000 TRANS-SCAT Installation Instructions for Ford AOD 1980-1993 TCI 436000 Kit Contains: Qty. Description Five (5) Gaskets: Three (3) Valve Body One (1) Filter One (1) Duraprene Pan Two (2) Springs:

More information

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista

More information

MK-5000G exploded VieW

MK-5000G exploded VieW Frame accessories 38 cutting head Pump Assembly 39 connecting linkage foot pedal linkage 40 curtain blade guard 41 ENGINE Assembly 42 PARTS LIST A Frames - - A1 Frame, MK-5000 Main 1 155541 B Pivot Bracket

More information

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed.

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed. 1 INSTRUCTIONS TCI 274500/274501 4L80E Trans Brake Valve Body Thank you for choosing TCI products. We are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning

More information

Installation Manual. For ISC, ISL, ISC03 And ISL03 Engines

Installation Manual. For ISC, ISL, ISC03 And ISL03 Engines Installation Manual For ISC, ISL, ISC03 And ISL03 Engines Table of Contents 1. Installation of the E Brake Assembly... 3 2. Pneumatic Group Installation... 5 3. Installation of the Controls... 7 4. Final

More information

Shotgun Single Barrel HPFP install guide

Shotgun Single Barrel HPFP install guide Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective

More information

4L80E HD SHIFT RECALIBRATION KIT PART # 4L80ECC/HDSRK

4L80E HD SHIFT RECALIBRATION KIT PART # 4L80ECC/HDSRK 4L80E HD SHIFT RECALIBRATION KIT PART # 4L80ECC/HDSRK Kit Contents: 1 Purple Pressure Regulator Spring 1 Orange Pressure Regulator Spring 1.375 Cup Plug 1 Separator Plate 1 Upper Valve Body Gasket 1 Lower

More information

2004R SHIFT RECALIBRATION KIT #24RSRK-A

2004R SHIFT RECALIBRATION KIT #24RSRK-A 2004R SHIFT RECALIBRATION KIT #24RSRK-A This easy to install kit includes all the necessary parts to recalibrate the hydraulic circuitry of the GM2004R transmission for high performance street and drag

More information

Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions)

Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions) Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions) Please take the time and read these instructions first! The GR40 S197 system is designed

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0

More information

Iron GEN III - Technical Notes

Iron GEN III - Technical Notes DART Iron GEN III - Technical Notes Deck Height... 9.240" Bore... 4.000 & 4.125 Main Bearing Size... LS-1 (2.558" 2.559") Weight... 227lbs Largest Recommended Bore..... 4.185" Largest Recommended Crank

More information

C40008 & C40009 EXHAUST BRAKES

C40008 & C40009 EXHAUST BRAKES EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the

More information

SDS Continental O-200 Installation Manual Aug. 4/17

SDS Continental O-200 Installation Manual Aug. 4/17 SDS Continental O-200 Installation Manual Aug. 4/17 This manual covers the steps to install the SDS EM-5 fuel injection and ignition system components on O-200 engines. Hall Sensor and Bracket Install

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

Single Barrel Shotgun HPFP Install Guide

Single Barrel Shotgun HPFP Install Guide Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should

More information

INSTALLATION INSTRUCTIONS FUEL RAIL

INSTALLATION INSTRUCTIONS FUEL RAIL INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:

More information

4 L E. Part No. SC-4L80E. Transmission Reconditioning Kit FULL COMPAT I B I L I T Y PUMP PA RT S VA LVE BODY PA RT S R E A S S E M B LY PA RT S

4 L E. Part No. SC-4L80E. Transmission Reconditioning Kit FULL COMPAT I B I L I T Y PUMP PA RT S VA LVE BODY PA RT S R E A S S E M B LY PA RT S 4 L 8 0 - E Transmission Reconditioning Kit Part No. SC-4L80E FULL COMPAT I B I L I T Y Full compatibility with 1991 and up. PUMP PA RT S Boost valve kit (34200-01K) Wide stator bushing (34016-W) End plugs

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR GENERAL MOTORS G BODY DISC SPINDLE

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR GENERAL MOTORS G BODY DISC SPINDLE ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH 1.88 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP 10-198 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

Attention! The following must be done to maintain consistent staging with all Tranz Brake Valve Bodies for Three (3) Speed Automatics: Before

Attention! The following must be done to maintain consistent staging with all Tranz Brake Valve Bodies for Three (3) Speed Automatics: Before Attention! The following must be done to maintain consistent staging with all Tranz Brake Valve Bodies for Three (3) Speed Automatics: Before turning bottom final stage yellow light on, you should be at

More information

Part # Chevy Level 2 Air Suspension Package One Piece Frame

Part # Chevy Level 2 Air Suspension Package One Piece Frame 350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11020299 55-57 Chevy Level 2 Air Suspension Package One Piece Frame Front Components: 1 11013001 Master

More information

STERILMATIC DIGITAL ELECTRIC STERILIZER PARTS AND SERVICE MANUAL

STERILMATIC DIGITAL ELECTRIC STERILIZER PARTS AND SERVICE MANUAL STERILMATIC DIGITAL ELECTRIC STERILIZER PARTS AND SERVICE MANUAL EFFECTIVE JULY 19, 2017 Superseding All Previous Parts Lists. The Company reserves the right to make substitution in the event that items

More information

ITEM QTY CHECK PART NUMBER DESCRIPTION

ITEM QTY CHECK PART NUMBER DESCRIPTION PART #90542A Boost Gauge Package, SLP, 2005-2013 Corvette PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION

More information

HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE

HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE INSTALLATION INSTRUCTIONS Time will be saved if these instructions are read PRIOR to installation of the intercooler package. A. ITEMS TO

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH 0.75 DIAMETER SOLID ROTOR 97-978 PINTO / MUSTANG II (FIVE LUG CONFIGURATION ONLY)* PART NUMBER GROUP 0-03-B DISC BRAKES SHOULD ONLY BE INSTALLED

More information

Technical Service Information

Technical Service Information Technical Service Information VOLVO/SAAB AW0-4LE VALVE BODY EXPLODED VIEWS AND IDENTIFICATION OF COMPONENTS Refer to Figure 1 for Solenoid identification and locations on the valve body. Refer to Figure

More information

Torqueflite Trans-Scat Kit

Torqueflite Trans-Scat Kit TCI 220000 Torqueflite Trans-Scat Kit This kit can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts and procedures. Work

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter

More information

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest.

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest. Global West Suspension 655 South Lincoln Ave San Bernardino Ca. 92408 Phone 877-470-2975 Fax 909-890-0703 Web address globalwest.net Mustang coilover instruction sheets for 64-66 Kit includes the following

More information

Installation Instructions

Installation Instructions 2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com

More information

84-86 Ford SVO Mustang AC Installation Guide

84-86 Ford SVO Mustang AC Installation Guide 84-86 Ford SVO Mustang AC Installation Guide This installation guide is for the AC installation kit from Late Model Restoration. The Vendor is Hose Wizards that manufactures this great kit that provides

More information

Installation Instructions Transpak Fits: GM Turbo-Hydramatic 400, Turbo-Hydramatic 375 and M40 Automatic Transmission Catalog # 20228

Installation Instructions Transpak Fits: GM Turbo-Hydramatic 400, Turbo-Hydramatic 375 and M40 Automatic Transmission Catalog # 20228 Installation Instructions Transpak Fits: 1965-1987 GM Turbo-Hydramatic 400, Turbo-Hydramatic 375 and M40 Automatic Transmission Catalog # 20228 WORK SAFELY! For maximum safety, perform this installation

More information

Part # Galaxie Level 1 Complete Air Suspension System

Part # Galaxie Level 1 Complete Air Suspension System 350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12160199 60-64 Galaxie Level 1 Complete Air Suspension System Front Components: 1 12162409 Front RQ Series

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (.36 OFFSET) BIG BEARING FORD PART NUMBER GROUP 0-739 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED

More information

Installation Instructions TH700-R4 (4L60) Transkit Part No thru 1986 Part No thru 1993 non-electronic models

Installation Instructions TH700-R4 (4L60) Transkit Part No thru 1986 Part No thru 1993 non-electronic models Installation Instructions TH700-R4 (4L60) Transkit Part No. 70232 1982 thru 1986 Part No. 70233 1987 thru 1993 non-electronic models B&M Racing and Performance Products 2009 Congratulations! You have just

More information

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST INSTALLATION INSTRUCTIONS

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST INSTALLATION INSTRUCTIONS 1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions

More information

TURBO KIT INSTRUCTIONS

TURBO KIT INSTRUCTIONS Revision 12/20/10 TURBO KIT INSTRUCTIONS This turbo kit consists of the necessary parts to upgrade or add a turbo to your 22R/RE/RET. This kit may require some fabrication to address your particular application

More information

Chevy Nova Pro-Touring Front Suspension Installation Instructions

Chevy Nova Pro-Touring Front Suspension Installation Instructions 1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com 1 Pro-Touring Clip A-Arm Assembly Sway Bar Assembly Fender Panel Kit 8 7/16-20 * 1 ¼

More information

HD372A DISASSEMBLY SLIDES

HD372A DISASSEMBLY SLIDES COMPRESSORS 03/93 CB-128 HD372A DISASSEMBLY SLIDES Each slide has a descriptive paragraph. Each paragraph has the main points outlined so reading the full text word for word is not necessary when presenting

More information

Fig Variable Speed Valve Parts

Fig Variable Speed Valve Parts 5 DISASSEMBLY OF VARIABLE SPEED CONTROL VALVE (Seal Replacement with Control Valve in the Bobcat). Remove seat and seat plate (Fig. ).. Remove variable speed control lever linkage rod. 3. Remove temperature

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

Geared Drives 200Z PSRU Zero Offset Gearbox with Centrifugal Clutch Assembly

Geared Drives 200Z PSRU Zero Offset Gearbox with Centrifugal Clutch Assembly Instructions for Removing and replacing Gen X Gearbox with Geared Drives 200Z Prior to your gear box arriving: Using a strap or chain and an engine hoist to hold your engine up in the mount, remove your

More information

INSTALLATION INSTRUCTIONS 68RFE ZERO-TUNE.

INSTALLATION INSTRUCTIONS 68RFE ZERO-TUNE. 1 TORQUE SPECIFICATIONS 2 IMPORTANT: The RevMax ZeroTune kit requires the transmission to be removed from the vehicle and be partially disassembled. It is recommended that a professional transmission technician

More information

RUBICRAWLER - JEEP TJ & JK ( ) W/ UNIVERSAL SHIFTER KIT CONSISTS OF: No. Qty Part No. Description

RUBICRAWLER - JEEP TJ & JK ( ) W/ UNIVERSAL SHIFTER KIT CONSISTS OF: No. Qty Part No. Description KIT CONSISTS OF: No. Qty Part No. Description 1. 1 RUBICRAWLER - GEAR BOX 2. 1 42R-UNIV - UNIVERSAL SHIFTER KIT PAGE 1 OF 8 Page Rev. Date: 11-06-18 Optional Items: Part No. Description 15-1000 - UNI-RAISE,

More information

CHEETAH Competition Manual Valve Body - (PRN321) Part #27253

CHEETAH Competition Manual Valve Body - (PRN321) Part #27253 1535 Owens Road, Jacksonville, FL 32218 Phone 904-741-4850 * Fax 904-741-4853 CHEETAH Competition Manual Valve Body - (PRN321) Part #27253 Turbo Hydro 200-1976-Up FIRST, READ INSTRUCTIONS CAREFULLY, THEN

More information

Installation Instruction for '84-'89 Nissan 300ZX High Performance Intercooler System (Part No )

Installation Instruction for '84-'89 Nissan 300ZX High Performance Intercooler System (Part No ) Installation Instruction for '84-'89 Nissan 300ZX High Performance Intercooler System (Part No. 2-124) Page ii DCB (06/14/02 12:19 AM) Version 1.0 Page iii Table of Contents 1. TOOLS REQUIRED...1 2. INSTALLATION

More information

Trackspeed Engineering, LLC 1289 Reamwood Ave #A, Sunnyvale, CA

Trackspeed Engineering, LLC 1289 Reamwood Ave #A, Sunnyvale, CA Trackspeed Engineering, LLC 1289 Reamwood Ave #A, Sunnyvale, CA 94089 650-701-7223 info@trackspeedengineering.com Trackspeed DIY Turbocharger System Installation Instructions v1.00 (10/12/16) Thanks for

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

C44090 HP325 PACBRAKE COMPRESSOR CONVERSION

C44090 HP325 PACBRAKE COMPRESSOR CONVERSION C44090 HP325 PACBRAKE COMPRESSOR CONVERSION APPLICATIONS: DODGE 2003-2007 5.9L CUMMINS Compressor Replacement Instructions for C14030, C14045, C44030, C44045, C44049 & C44052 with Air Tank KIT CONTENTS

More information