RC4WD Timberwolf Build Document
|
|
- Coleen Lee
- 5 years ago
- Views:
Transcription
1 RC4WD Timberwolf Build Document This build document is for informational purposes. Since the Timberwolf can come in so many different combinations, this will not fit everyone. If you find that you still have questions. Please feel free to use the RC4WD forum. In this build up I will be using the T-Rex 60 Plastic axles, and the Dual Spring scale shocks 110mm. I used my own custom link, but this should not vary from your kit. I am using the standard R2 transmission. Along with the T-rex axles I used the standard upper 4 link mounts, and the servo mount that comes with it. I will be also using the RC4WD punisher shaft. The first thing you will want to do is an inventory of all the items you have. Make sure that you have all the items you need to do you build. After this.get started. I use Blue threadlocker anytime I have metal to metal items. This is a preference of mine, it may save you some hassle when you start to run your truck. Just be careful and use sparingly. Here shows the items we are going to use in the first few steps. You will need the axles, 4 link mounts, uppers and lowers, and the front servo mount. Make sure to may close attention to the lower 4 link mounts and the way they install onto the axle.
2 Here shows it mounted to the axle. Next we will install the upper 4 link mounts. Here is the upper link mount.
3 I found it easier to mount this off the axle with the upper 4 link mounts. You may be able to do it on the axle. Here shows how it looks mounted off the axle.
4 Mounted on the axle. This photo show the lower and upper links mounted to the axle. You can see the way they are mounted. Again, depending on you links and axles this might be different. Questions can be referred to RC4WD forum.
5 Shot from the top Under side shot of the links.
6 In some cases when installing the links you may want to use a spacer to offset the link a small bit. This will help prevent binding. In this photo shows a close up of what I am talking about. After all 4 front and rear links are mounted you should have something like this.
7 Take a moment and make sure you have good movement of the links front and rear. If not, do some investigating of the links and see if there is any binding. If so, access the situation and try to solve the problem with spacers. If you still have issues and can t figure out the issue try the RC4WD forum. Let s mount the R2 Tranny. There are a series of 6 holes in the bottom of the delrin plate. You can mount the tranny to the front, or farther back. You make the choice and install. Make the screws you use are not to long. They could catch a gear inside the tranny. Installation of the motor is a good idea at this point. Once the tranny is mounted it may be harder to install the motor.
8 Next will be installation of the Punisher shafts. These are pretty simple. Install the front and rear both. Should look like this!
9 I installed the front servo next. This is an adjustable servo mount. So you can set it up several different ways.
10 You can now install the servo links and servo arm. Again this is something that varies by kit. Remember you can move the servo mount around depending on the size of your links.
11 The Shocks can be installed next. This shows the position I mounted the 110mm shocks I have. Different sizes will need mounted in different positions. I used two small spacers on the bottom and one at the top. The one at the top prevented binding and the one s at the bottom helped to space the shock out a little. This helps with the shock geometry. Bottom
12 Top With the truck set-up, you can install and mount the electronics. Since there are various sizes of electronics there may be different places you may want to mount them. I would recommend either on the front plate, or on the inside of the skid plates.
13 You can always keep the build going and add some scale details. Here shows a few closeup shots of mine. For the dash I used some styrene and molded it around the front bar. After I had the fit right I painted it and added the dash details. Then I used two cable ties to secure it in place. It fits real snug around the bar to help hold it into place as well.
14 I again used styrene again for the rear deck. This time I used flat plate to make the form and then layered it with Diamond plate styrene. After I was finished I painted it and added the scale details.
15 For body mounting. Go here. Body Mounting Instructions. Install the wheels and your ready to run. Some additional tweaking may be needed. Here are a couple shot. Hopefully yours will be less worn. I ran mine a little and then added these great axles and shocks.
16 Please enjoy your truck. If you have any further question please use the RC4WD forum.
RC4WD TrailFinder Instruction Manual
Version 1.1 RC4WD TrailFinder Instruction Manual Thank you for your purchase. Welcome to the RC4WD family. This kit is a combination of many specially engineered and manufactured parts. Enjoy your build.
More informationRC4WD Diablo Instruction Manual
Version 1.1 RC4WD Diablo Instruction Manual Thank you for your purchase. Welcome to the RC4WD family. This kit is a combination of many specially engineered and manufactured parts. Enjoy your build. This
More informationCALDERA 10E Spur Gear Change
CALDERA 10E Spur Gear Change www.thirdcoastrc.com ebay handle - little*oak Click Below to Visit our Ebay Store EBAY STORE (Please take a moment and bookmark my website, ebay store, and save me as an ebay
More informationW123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way
W123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way Why do you need to do this?: You need to do this to properly check the internal hydraulic pressure of the transmission, either
More informationWe thank you for purchasing a manual petcock conversion kit from Murphs!
We thank you for purchasing a manual petcock conversion kit from Murphs! The first step is removing the gas tank from the bike. We suggest running the tank down to reserve before removal, both for the
More informationHere's the difference (externally) in the and 04+ bumper and headlights: (00-03 on top, 04 on bottom)
OK guys, I've been meaning to post this for awhile.. well here it goes. I did the '04 front end conversion on my '01 about 4-5 months ago, but then the dealer had to buy the car back for legal reasons.
More informationInstalling LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)
Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationLong Wheelbase D110. 1/10 SCALE 4x4 TRUCK KIT
Long Wheelbase D110 1/10 SCALE 4x4 TRUCK KIT Recommended Tools Hex Drivers (1.5mm, 2mm, 2.5mm) Thread Lock Cross Wrench Long Nose Pliers Tips for Assembly Use good quality hex drivers to avoid stripping
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More information~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ GSB Design Concepts Runnin' At Redline 7/9/17 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Guest Shot: Gene Mills I've known Gene for a number of years,
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationMAC Catback Exhaust (86-93 LX; GT)
MAC Catback Exhaust (86-93 LX; 94-95 GT) Installation Time: 3-4 hours for a novice, including time for adjustments. Tools recommended: Sawz-all or hacksaw, or exhaust cutoff tool 7/16 deep socket and/or
More informationBBK Caster/Camber Kit (87-93)
BBK Caster/Camber Kit (87-93) Materials in the box 2 Polished Aluminum Plates 2 Steel Strut Mounts 4 Polyurethane Bushings 2 Stud Plates 2 Bushing Sleeves 2 5/8 Flat Washers 2 5/16 Allen Head Bolts 4 5/16
More information2005 to 2008 #08 Metric Nova Chassis Set Up Sheet
Springs 1 2005 to 2008 #08 Metric Nova Chassis Set Up Sheet Flat end of spring down on tubular lower a-arms. Left Front 800lb. Right Front 750lb. Left Rear 200lb. Right Rear 225lb. On Top of Tube Axle
More informationArrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual. M8 II weight: 925 grams Dimensions
Arrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual M8 II weight: 925 grams Dimensions Parts List M8V2#0001 Billet Lower Unit M8V2#0013 Steering Cable Assembly M8V2#0002 Steering Arm Housing
More informationHow To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg
How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationWe all put our heads together to try and determine what the facts were. They were as follows:
VWvortex Forums > Eos > How to solve (or prevent) Eos Roof leaks As many of you know, I don t own an Eos. This makes it difficult to provide practical advice based on my own experience with the car, as
More informationJ&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions
J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Adjustable Panhard Rod (05-09) Please read through
More informationALIGNING A 2007 CADILLAC CTS-V
ALIGNING A 2007 CADILLAC CTS-V I ll describe a four-wheel alignment of a 2007 Cadillac CTS-V in this document using homemade alignment tools. I described the tools in a previous document. The alignment
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationLUGGAGE RACK MG TD with Original Steel Wheels. Installation Instructions. Step 1
Created on 7/7/2003 8:34:00 PM by Michael Grant Last Revised 2/2/2008 1:55:00 PM Page 1 of 14 1 2 3 243-705 LUGGAGE RACK MG TD with Original Steel Wheels If your TD has been converted to wire wheels, please
More informationFigure 6 - This photo shows the two types of rods; the top one simulates the brake rod that connects to the brake equipment in the truck while the
These two segments appeared as sidebars to two installments of Essential Freight Cars in the August and September, 2003 issues of Railroad Model Craftsman. Text and photos Ted Culotta. Distribution for
More informationLEGO Ferrari F40 (10248) Lighting Kit Installation Instructions
LEGO Ferrari F40 (10248) Lighting Kit Installation Instructions This guide walks you through the steps to install the Brickstuff lighting kit for the LEGO Ferrari F40 (LEGO set #10248). Written By: Rob
More informationThe Life of a Lifter, Part 2
Basics Series: The Life of a Lifter, Part 2 -Greg McConiga Last time we looked at some complicated dynamics and compared flats to rollers. Now for the hands-on. 6 FEATURE This off-the-shelf hydraulic lifter
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationRB5 MID CUSTOM SPECIAL INSTRUCTIONS MANUAL
RB5 MID CUSTOM SPECIAL INSTRUCTIONS MANUAL INTRODUCTION This manual is intended to the few people who were lucky enough to get their hands on a Mid Custom Special conversion for the Kyosho RB5. Due to
More informationAssembly Manual. 1/10th Formula 1 Car
Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp
More informationXD Aussie Locker XD Installation Supplement Dana 35 Ford TTB
XD-13527 Aussie Locker XD-13527 Installation Supplement Dana 35 Ford TTB Thank you for your purchase of the XD-13527 Aussie Locker for Dana 35 Ford TTB The following installation review is from username
More informationInstallation Guide for TeraFlex 3-inch Lift for Grand Cherokees (3Z)
Installation Guide for TeraFlex 3-inch Lift for Grand Cherokees (3Z) Think safety first when installing your new suspension system. Use these instructions to install the TeraFlex 3Z. Information regarding
More informationPENNSYLVANIA X29D PARTS HISTORY RECOMMENDED TOOLS
PENNSYLVANIA X29D Thank you for purchasing our WrightTRAK X29D boxcar kit. We hope that you find building this kit to be an enjoyable experience. If you find any pieces broken or missing please feel free
More informationACE 325/570 2 Lift Kit
ACE 325/570 2 Lift Kit Polaris Ace 325/570 2014+ Part #: 5101244 Rev. 082316 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro
More informationAn Actual Driving Lesson Learning to drive an automatic car
An Actual Driving Lesson Learning to drive an automatic car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationInstructional Video Productions and Sales
Instructional Video Productions and Sales Home DVD Info Pictorials Sales Images Updates to DVDs Contact Information Tire Change Pictorial on an R1200GS (similar on most bikes.) Caution: This pictorial
More informationW C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush
W203 2003 C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush First, I have to thank everyone who has contributed to the MBworld.org forums without you; I would not have gotten
More informationAdjusting brake shoes for AutoPark parking brake
Adjusting brake shoes for AutoPark parking brake This document is a compilation of several separate writeups. What we're trying to do here is consolidate the necessary information needed for you to make
More informationAn Actual Driving Lesson. Learning to drive a manual car
An Actual Driving Lesson Learning to drive a manual car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without looking
More informationStep 1: Place your jack under your car and raise the car until you have enough room to work with.
In this DIY, we will learn how to properly install aftermarket dogbone mount bushings. Dogbone bushings are advertised to reduce wheel-hop, provide better traction as well as prevent aftermarket downpipes
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationHow to Build with the Mindstorm Kit
How to Build with the Mindstorm Kit There are many resources available Constructopedias Example Robots YouTube Etc. The best way to learn, is to do Remember rule #1: don't be afraid to fail New Rule: don't
More information2010 Toyota Prius model II Head Unit Upgrade
2010 Toyota Prius model II Head Unit Upgrade Monday, December 21, 2009 Disclaimer: Use this document and its contents at your own risk. Forward: Huge thanks to those members on Priuschat.com that forged
More informationRAM FRONT RADIUS ARM DROP BRACKETS Installation Instructions
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SYNERGY MFG. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF SYNERGY MFG IS PROHIBITIED. Revisions Rev. Description
More informationWiring Harness Relocation by Flopster Mar 2012
Wiring Harness Relocation by Flopster843 21 Mar 2012 On my 2008 Ram, there is a gigantic blob of electrical wiring that Dodge decided to put between the engine and the brake master cylinder, just behind
More informationArduCopter v2.9.1 for Traditional Helicopters (TradHeli)
ArduCopter v2.9.1 for Traditional Helicopters (TradHeli) I have put this manual together from forums on DIYDRONES and would like to acknowledge the content creators, in particular; R_Lefebvre, Manfred
More informationTHE HAIRPIN: Talking about sliding sideways,
THE 3.107 MILE Autodromo de la Ciudad de Mexico track hosts the Mexican Grand Prix. It is the highest track in terms of elevation at about 5,000 feet above sea level. This reduces the amount of horsepower
More informationOnce again, another four weeks have gone by and I am quite sure everyone is tired of me wondering where the time has gone. To say that everything
Once again, another four weeks have gone by and I am quite sure everyone is tired of me wondering where the time has gone. To say that everything around the shop has been a little chaotic during this time,
More informationModdit. How to Install Stance Coilovers on a Subaru
Moddit How to Install Stance Coilovers on a Subaru BRZ Let's get LOW (and maybe lighter and stiffer suspension)! In this article, we will install Stance ST- ZN6-XS Coilovers on the FRSport Subaru BRZ.
More informationGrilleGuy.com, LLC. Installation Instructions and Care guide : Scion tc : Honda S2000 : Honda Civic
Installation Instructions and Care guide : 2005 2009 Scion tc : 2000 2003 Honda S2000 : 2004 2005 Honda Civic Thanks again for purchasing your custom grille insert from the GrilleGuy. The following are
More informationSTEP #1: Remove the wheels from the truck. There are (6) 21mm lug nuts holding each wheel on... Remember Lefty Loosy, Righty Tighty.
- CustomTacos.com Page 1 of 36 How-To: Toytec Lift Install Read all of these install instructions prior to installing Toytec's suspension lift. I cannot be held responsible for any damages or personal
More information2k2GT Registered User
1 of 44 7/22/2009 01:17 Corral Forums > Modular Tech Forums > GT & SOHC My J.R. Granatelli K-member install story...56k death Welcome, xomp. You last visited: Today at 12:07 AM Private Messages: Unread
More informationUseless Machine. GM3 Edition
Useless Machine GM3 Edition Shown with peelable protective brown paper As seen on: Saskview.com instructables.com/id/the-most-useless-machine/ makeprojects.com/project/the-most-useless-machine/91/1 www.solarbotics.com
More information1/10 Desert Runner Scale Truck ARTR/RTR w/hero Hard Body Set
1/10 Desert Runner Scale Truck ARTR/RTR w/hero Hard Body Set 1 Specifications: Truck Size: 610mm x 220mm x 215mm (24.02" x 8.66" x 8.46") (L x W x H) Packing Size: 750mm x 330mm x 295mm (29.53" x 12.99"
More informationFig 1 An illustration of a spring damper unit with a bell crank.
The Damper Workbook Over the last couple of months a number of readers and colleagues have been talking to me and asking questions about damping. In particular what has been cropping up has been the mechanics
More informationLab 6: Magnetic Fields
Names: 1.) 2.) 3.) Lab 6: Magnetic Fields Learning objectives: Observe shape of a magnetic field around a bar magnet (Iron Filing and magnet) Observe how static charged objects interact with magnetic fields
More informationHitachi Alternator Upgrade for Series I E-Types Ray Livingston (831) Home (831) Cell
Hitachi Alternator Upgrade for Series I E-Types Ray Livingston (831) 457-1373 Home (831) 234-0858 Cell rayl@atc.creative.com The Hitachi alternator for a 1986 Nissan pickup is a perfect replacement for
More informationSolar System Main Panel
Solar System Main Panel Copyright Kelly J. Lipp 2013, All Rights Reserved. May not be copied without permission. This paper highlights the design and wiring of the solar power main system control panel
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationDevice to Rotate Rail Cars By: Chuck Hackett
Device to Rotate Rail Cars By: Chuck Hackett (MiscCDH@WhiteTrout.net) I have had several requests to provide more info about the device I built to rotate my passenger cars to make it easier to work on
More informationMagnaflow MF Series Cat-Back Exhaust Dual Side Exit - Before Rear Tire p/n: F150 Extended Cab
Magnaflow MF Series Cat-Back Exhaust Dual Side Exit - Before Rear Tire p/n: 19054 2015-2017 F150 Extended Cab Time Necessary: Approximately 1 hour Please Note: I ran into an issue with my install. This
More information7211 A-ARM FRONT, 4-LINK, 3 X 2 FRAME, INTERMEDIATE, ELIMINATOR CHASSIS ITEM QTY SIZE/PART NO. TUBE CODE DESCRIPTION
#917211 Page 1 of 6 7211 A-ARM FRONT, 4-LINK, 3 X 2 FRAME, INTERMEDIATE, ELIMINATOR CHASSIS ITEM QTY SIZE/PART NO. TUBE CODE DESCRIPTION 1 2 4138 Cage Side 2 2 4208 Forward strut 3 1 4038 Main Hoop 4 1
More informationAudi A8 Transmission Service By Barry Lenoble and Paul Waterloo
Page 1 of 18 Technical & Maintenance Upgrades & Style Used A8 Buyer's Checklist Marketplace On Track Gallery Links Contact Home Audi A8 Transmission Service By Barry Lenoble and Paul Waterloo Background
More informationESPA3D Photo Essay One page ESPA3D Plans are HERE Back to Spad Plans Index
1 of 8 8/29/2012 12:28 PM ESPA3D Photo Essay One page ESPA3D Plans are HERE Back to Spad Plans Index This little airplane has turned out to be one of the most fun Spad projects we've ever done! It is built
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationThe Starter motor. Student booklet
The Starter motor Student booklet The Starter motor - INDEX - 2006-04-07-13:20 The Starter motor The starter motor is an electrical motor and the electric motor is all about magnets and magnetism: A motor
More informationFITTING OIL TEMP AND PRESSURE GUAGES
FITTING OIL TEMP AND PRESSURE GUAGES this guide is of reference to fitting an oil temp and pressure sender/ sensor into a sandwich plate- not the sump plug temp sensor (although it wouldn't be much different
More information4x4 actuator "Cable Froze" 1988 s S-10 Forum
Page 3 of 17 Converting a vacuum actuator to a locking cable system on a 1995 Chevy S10 Blazer 4x4 Many call this a posi-lock system. I spent a total of only $25.50 USD on this project. Other comparable
More informationRight On Replicas, LLC Step-by-Step Review * Fruehauf Flatbed Trailer 1:25 Scale AMT Model Kit #617 Review
Right On Replicas, LLC Step-by-Step Review 20160330* Fruehauf Flatbed Trailer 1:25 Scale AMT Model Kit #617 Review A semi-trailer is a trailer without a front axle. A large proportion of its weight is
More informationRemoving your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! )
Removing your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! ) If you are having oil leaking around the propeller piston/cylinder assembly and
More informationBMW 3 Series Oxygen Sensor
1984-1991 BMW 3 Series Oxygen Sensor Replacement Replace an old oxygen sensor on your E30 for better gas mileage. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationLearning to Set-Up Your Warrior Drive Belt Arizona Warrior (Rev4) BEFORE GETTING STARTED
BEFORE GETTING STARTED 1. A noise one guy calls 'howling' is the same noise another guy calls 'squealing' so unless you are both hearing the noise with your own ears its better to not assume a drive belt
More information1/10 Competition Ready to Run Truck Little Orchard St. San Jose CA,
1/10 Competition Ready to Run Truck RC4WD WWW.RC4WD.COM 1855 Little Orchard St. San Jose CA, 95125 E-mail: rcrock@rc4wd.com Check out Precautions To Prevent Serious Personal injury and/or property damage,
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More information1209A GM B-BODY Double Adjustable Trailing Arms
1209A 78-96 GM B-BODY Double Adjustable Trailing Arms Warning: This installation should be performed by a trained professional. Tools Required for this Installation - 4 post lift or alignment rack preferable
More informationT R A I L R AT E D GUARANTEED. rc4wd quality R3 TRANSMISSION FOUR WHEEL DRIVE BEAD LOCK WHEELS
The TF2 SWB has both detailed styling and aggressive performance. You will find a balance of capability and performance built into every TF2. Performance of the TF2 is smooth and with its R3 single speed
More informationTIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided
TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided tape (not supplied.) Mount the ESC first on the chassis
More informationHOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS
HOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS Yup, it happened. The spoiler on your beloved Prius has departed this earth and now is in the great junkyard in the sky. This is how you make it all better
More informationG503 WWII Jeep changing of the oil and oil filter
G503 WWII Jeep changing of the oil and oil filter It is not difficult to change the oil and oil filter for your G503 WWII jeep. It can be a little messy, but if your prepared, you can do this yourself
More informationRobot Preparation for the VEX World Championship/ US Open. Lessons learned over the past 6 years by David Kelly 2013 VWC, Teacher of the Year
Robot Preparation for the VEX World Championship/ US Open Lessons learned over the past 6 years by David Kelly 2013 VWC, Teacher of the Year Re-designing Re-designing your robot to a new concept yields
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationFabricating and Installing Headlight Relays. Mike Graham
Fabricating and Installing Headlight Relays Mike Graham For some time I had been reading about the benefits of installing headlight relays. As I understand it, there are two principal benefits: the load
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationInstallation instructions for 1948 to 1952 Ford F-1 pick-up trucks. Getting started: Some recommendations : PLEASE TRY OUR WAY FIRST
Installation instructions for 1948 to 1952 Ford F-1 pick-up trucks The Raingear s modern lever and link electric windshield wiper system for 1948 to 1952 Ford F-1 pickups provides a direct mechanical link
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More informationTRU-Turn JK Tie rod Installation Document
TRU-Turn JK Tie rod Installation Document Off Road Only ph 651.644.2323 www.offroadonly.com oro-info@offroadonly.com The TRU-Turn will bolt onto the stock JK steering knuckles at the stock tapered tie
More informationWARNING These following pages are instruction for C5 CE stripes; however, it is the same method applying vinyl. Please spend time to read thru these
WARNING These following pages are instruction for C5 CE stripes; however, it is the same method applying vinyl. Please spend time to read thru these pages. At the end, it is your C5/C6 ME stripes' instruction.
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationTHE TORQUE GENERATOR OF WILLIAM F. SKINNER
THE TORQUE GENERATOR OF WILLIAM F. SKINNER IN 1939, WHICH WAS THE START OF WORLD WAR TWO, WILLIAM SKINNER OF MIAMI IN FLORIDA DEMONSTRATED HIS FIFTH-GENERATION SYSTEM WHICH WAS POWERED BY SPINNING WEIGHTS.
More informationGeared Drives 200Z PSRU Zero Offset Gearbox with Centrifugal Clutch Assembly
Instructions for Removing and replacing Gen X Gearbox with Geared Drives 200Z Prior to your gear box arriving: Using a strap or chain and an engine hoist to hold your engine up in the mount, remove your
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationGM A-Body Instructions 3 & 2½ Header Applications w/ Balance Tube Crossover
GM A-Body Instructions 3 & 2½ Header Applications w/ Balance Tube Crossover Included with this kit are the following: 2 Collector Reducers 1 Balance Tube Kit A 2 Headpipes 2 Tailpipes 2 Tailpipe Extensions
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More informationBuilding Robots with Lo-tech Materials
Building Robots with Lo-tech Materials 1 By Andrew Fisher When you think about robots, you probably imagine drones, self-driving cars, or humanoid robots like Atlas or Asimo. Many of these more serious
More information