Step 1: Place your jack under your car and raise the car until you have enough room to work with.
|
|
- Pauline Ariel Shepherd
- 5 years ago
- Views:
Transcription
1 In this DIY, we will learn how to properly install aftermarket dogbone mount bushings. Dogbone bushings are advertised to reduce wheel-hop, provide better traction as well as prevent aftermarket downpipes from rubbing. There are many companies that offer replacement bushings, each have different durometer ratings (how stiff they are). The higher the rating, the more stiff = more vibrations. Tools needed : - Torque wrench - Jack (hopefully not the factory widowmaker!) & a jackstand - 16mm (5/8") socket - 13mm (1/2") socket - WD40 or similar spray
2 Step 1: Place your jack under your car and raise the car until you have enough room to work with. Step 2: Use jackstands to keep the car elevated. Place a jack or jackstand underneath the subframe
3 to hold it in place. Your setup should be similar to this optimally: Step 3: There are 4 bolts that hold the dogbone mount to the engine. Use WD40 or a similar
4 penetrating spray to help the bolts come out easier. Remove the two 13mm, red circled bolts that are connected to the subframe, and the two 16mm, blue circled bolts that are connected to the bottom of the transmission.
5 Step 4: You should be left with a dogbone mount and 4 bolts as seen below.
6 Step 1: Remove the 16mm bolt on the top of the mount.
7 Step 2: After removing the 16mm bolt, remove the pieces from top to bottom. Keep track of the compression nut. The disassembled mount appears below, the stock black bushings will be replaced with the aftermarket inserts.
8 Inserting aftermarket inserts: Step 1: Slide the smaller, bottom insert over the rod of the bottom piece while lining up the ridge. Some grease can be used to help the piece slide easier. Step 2: Slide the larger metal cover over the bottom insert. Slide the remaining insert into its place by correctly aligning it with the top ridges.
9 Step 3: Slide the outer metal cover on top of the top insert. Align the 16mm bolt into the center of the mount. Place the compression nut in its slot.
10 Step 4: Fasten the mount to a vice or a device that will keep it stationary. Align the compression nut on the bottom and compress the mount so that it catches. You can use your body weight, a vice, or pliers. Torque the compression nut to 20 Nm (15ft-lbs) + 1/4 turn.
11 Step 5: Your dogbone mount is now completely assembled, isn't it pretty? :D
12 Step 1: Re-align the dogbone mount and install the bolts. Torque the two 13mm, red circled bolts that go into the subframe 20 Nm (15 ft-lbs), plus an additional 1/4 turn. Torque the two 16mm, blue circled that go into the bottom of the transmission 40 Nm (30 ft-lbs), plus an additional 1/4 turn.
13 Step 2: The dogbone install is now complete! The install took my friends and I about 1 hour going at a smooth, steady and slow pace. Carefully lower your jack and test drive your car!
14 First impressions: You've just finished installing the mounts and you are probably anxious / nervous, or at least I was. I started the car expecting severe vibrations, however, this was not the case! The difference in idle vibration was not apparent. However, the car does vibrate a little at idle with the AC on. It also vibrates a bit as you are start rolling in first gear from RPMS - however, this would also be the case with the stock mounts because the car is "bogging". Just be sure to give it a little more gas as you let the clutch out. Driving test: At first I just drove the car slow to warm up. I noticed the shifting was a little smoother / crisp. Once the car was warm, my buddy and I headed to some straight streets. I was rolling in first, at about 15 or so MPH, and then I just slammed the gas. Before the mounts there would be a massive amount of wheelhop that would feel very annoying and rough. With the new inserts, the car just pulled so much smoother and harder. Although you aren't gaining any power, you will definitely notice better acceleration due to the fact that more power will be transferred to the ground. This is the best 30 dollars I have ever spent on any of my cars! The price tag is definitely justified, your MK4 will pull so much smoother and harder without succumbing to wheelhop.
Make sure your vehicle is on a level surface prior to starting installation.
Thank you for purchasing the CorkSport Mazdaspeed 3 Front Sway Bar. Our sway bar will help remove the vehicles tendency to overpower the front tires under hard cornering and minimize traction robbing body
More informationMake sure your vehicle is on a level surface prior to starting installation.
Thank you for purchasing the CorkSport Mazdaspeed 3 Front Sway Bar. Our sway bar will help remove the vehicles tendency to overpower the front tires under hard cornering and minimize traction robbing body
More information034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit, MkV/MkVI Volkswagen & 8J/8P Audi
034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit, MkV/MkVI Volkswagen & 8J/8P Audi The installation of your 034Motorsport Stainless Steel Subframe Locking Collar Upgrade Kit for the 8J/8P
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough
More informationWe recommend installing the TRS Racebars first as we have done
Thanks for purchasing the 2 Front Lowering Kit for the Honda Grom (MSX125). This is a basic installation guide, and we tried to cover everything, but use your best judgment along the process. It is recommended
More information$1.00 FOR THE TQIO/RCIO
$1.00 FOR THE TQIO/RCIO m mm HDBBYSHOP Champion Jay Halsey has an impressive track record. One of Jay's advantages is a whisper smooth tranny thanks to his dad, Jim. Now you can build a Halsey transmission!
More informationFront Suspension Redo
Front Suspension Redo Message: First, thanks to all the previous posters for guidance in my doing the suspension. As thanks, here s the updated document for doing the front suspension. Procedure: While
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationRear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5
Rear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5 Supplied Parts: B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear Subframe Mount Insert Front (601-0033) x 2 B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationINSTALLATION INSTRUCTIONS. FD3S RX7 Manual Rack Conversion
INSTALLATION INSTRUCTIONS FD3S RX7 Manual Rack Conversion 1 Removal of Stock Rack 1.1 With your steering wheel centered, remove the pinch bolt from the factory intermediate shaft lower knuckle. If you
More informationInstall Guide Billet + Spherical MQB Dogbone Mount
Billet + Spherical Dogbone Mount, 8S Audi TT RS & Installation Spiciness Rating 8V Audi RS3 (Mild) Installation of your 034Motorsport Billet + Spherical Dogbone Mount is a straightforward process that
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough
More informationYou will be removing the suspension of your vehicle. If you are not comfortable with this or do not have the proper tools, please do not proceed.
Thank you for purchasing the CorkSport Mazda 3 and Mazdaspeed 3 Coilover Kit. This suspension system features 15-way adjustable dampening settings and full length adjustment to meet every driver s handling
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit for Kawasaki KX80/85/100 OVERVIEW INSTALLATION & USER S GUIDE Doc ID: 191-7742A Doc Rev: 073015 This kit replaces the OEM core clutch components including
More informationReplace front brake pads and discs * (Ford Galaxy )
Replace front brake pads and discs * (Ford Galaxy 2006-2015) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're
More informationExedy Mach 400 Stage 1 Clutch and Pilot Bearing (Late GT, Bullitt, Mach 1; Cobra): SKUs: & 50116
Exedy Mach 400 Stage 1 Clutch and Pilot Bearing (Late 01-04 GT, Bullitt, Mach 1; 99-04 Cobra): SKUs: 62502 & 50116 Tools Needed: Car Jack with high lift capabilities (If not, block of wood may be required)
More informationBADEN'S BMW DIY #7 E46 Shock and Strut Replacement
- Baden's Car Pages web site - http://www.badenscarpages.ca - DIY #7 E46 Shock and Strut Replacement Posted By Baden On February 15, 2010 @ 1:38 PM In E46 39 Comments BADEN'S BMW DIY #7 E46 Shock and Strut
More informationJ&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions
J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Adjustable Panhard Rod (05-09) Please read through
More informationDrum 2 disk brake conversion. Stop That Car!
Page 1 of 9 Stop That Car! From the February 1993 issue of "Petersen's Musclecar Restoration and Performance". Illustration by: Dennis Ellefson GM BUILT PLENTY OF CARS WITH FRONT DISC BRAKES. IF YOUR A-BODY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Disc Brake Spindle Kit SUM-BKA2447 1964-72 A-BODY 1967-69 F-BODY 1968-74 X-BODY Thank you for choosing SUMMIT RACING for your braking needs. Please take the time to read and carefully
More informationMazdaspeed 6 Version 2 Oil Catch Can Kit Install Guide
Mazdaspeed 6 Version 2 Oil Catch Can Kit Install Guide Copyright DD2, Inc. 1 WARNING: By installing this Product, you understand that: The buyer/user assumes all risk as to quality, performance and use
More informationINSTALLATION INSTRUCTIONS Unitronic 3 Turbo-Back Exhaust System for Golf R UH021-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationFord Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions
Ford Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions Time Necessary: Approximately 1.5 hours Tools Required: 15 MM Socket Ratchet PryBar Floor Lift or: o Floor Jack o (2) Jack Stands
More informationPML Installation Review p.k.y. 19 April 2014
Reason for installing a PML 11036 transmission pan on my 2010 GMC Savana 3500: 1. My 2010 GMC 3500, 12 foot box truck is placed under heavy hauling condition (construction tools and building material)
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise
More informationShould I Leave My Manual Car In Gear When Parked
Should I Leave My Manual Car In Gear When Parked I just wanted to know who people leave there car in first gear while there car is It's definitely saved my car a few times since my parking brake cables
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.
More informationPypes 409 Stainless Steel Violator Cat-back with Polished 304 Tips Installation Guide (98-04 GT/Mach 1)
Pypes 409 Stainless Steel Violator Cat-back with Polished 304 Tips Installation Guide (98-04 GT/Mach 1) The below installation instructions work for the following products: Pypes 409 Stainless Steel Violator
More informationAn Actual Driving Lesson Learning to drive an automatic car
An Actual Driving Lesson Learning to drive an automatic car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without
More informationMercedes Diesel Valve Adjustment Procedure
1 of 30 5/30/2008 12:58 PM Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips,
More informationBMW F8x M3 & M4 Valvetronic Exhaust System
BMW F8x M3 & M4 Valvetronic Exhaust System SKU: FS.BMW.F8X.VLVP Required Tools Hydraulic Lift or Floor Jack & Stands Metric Socket Set w/ Ratchet & Extensions Metric Open-End Wrench Set Inverted Torx Bits
More information2001 V70 T5 ETM Removal and Cleaning Directions
2001 V70 T5 ETM Removal and Cleaning Directions Howard Cheng howardc64@gmail.com 10/24/05 Version 1.4 Read this before you start I performed this ETM cleaning because I had gotten 2 reduced performance
More informationThis is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationBosch hydraulic cylinder inlet ports seals replacement Ivan Ruiz December 2017
Bosch hydraulic cylinder inlet ports seals replacement Ivan Ruiz December 2017 I recently purchased a Khamsin and noticed some hydraulic fluid (LHM) leakage in the areas under the headlights. I also noticed
More informationCan You Put Automatic Transmission Fluid In A Manual Car
Can You Put Automatic Transmission Fluid In A Manual Car WIth an automatic, you basically just need to check the dipstick and fill it up, as needed. To check the transmission fluid in a manual vehicle,
More information---Optional Items---
1 2 3 4 5 6 ---Optional Items--- 10 9 11 7 8 12 This package should contain: 1. One (1) CorkSport Crashbar Weldment 2. Eight (8) M8x1.25x20 mm Bolts 3. Eight (8) M8x1.25mm Nyloc Nuts 4. Sixteen (16) M8
More informationINSTALLATION GUIDE. Doc ID: C Doc Rev:
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit INSTALLATION GUIDE Doc ID: 191-7700C Doc Rev: 012213 2012 Rekluse Motor Sports Rekluse Motor Sports, Inc. 12000 W Franklin Rd Boise, Idaho 83709 208-426-0659
More informationMAC Catback Exhaust (86-93 LX; GT)
MAC Catback Exhaust (86-93 LX; 94-95 GT) Installation Time: 3-4 hours for a novice, including time for adjustments. Tools recommended: Sawz-all or hacksaw, or exhaust cutoff tool 7/16 deep socket and/or
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationNOTE: Visit our website at for video repair procedures, under the Tools section.
Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.
More informationJ&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions
J&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Rear Lower Control Arms (2005+) Please read through
More informationSR Performance Sway Bars (2010 Mustang GT)
Total Installation time: Approximately 2 hours SR Performance Sway Bars (2010 Mustang GT) Tools Required: 15mm deep socket 18mm deep socket 19mm deep socket Ratchet with ½ drive Pliers Torque wrench 15mm
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationRZR 570 SLP Clutch Kit Installation Instructions
RZR 570 SLP Clutch Kit Installation Instructions Clutch Removal Illustration #1 A-1. Jack up the rear of the RZR until the driver side rear suspension is at full droop and the rear tire is off the ground.
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationThis is an aluminum-case PowerGlide Transmission out of a 1966 Chevelle.
Removal Procedures ***Take a picture of the transmission and note the lever positions (Transmission Arm Lever points up and Kickdown Lever point down)*** This is an aluminum-case PowerGlide Transmission
More informationAnti-Sway Bars Installation Instructions For Mazda MX-5 PART #
Anti-Sway Bars Installation Instructions For 2006+ Mazda MX-5 PART # 920-330 Tools required: A jack and jack stands, 5mm Allen wrench, ratchet, 10mm, 12mm and 14mm, combination wrenches and sockets, 21mm
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationSteeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,
Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8
More informationFigure 1 Factory G50 update and old Shift Fork Shaft
911 Clutch Job So you have one of the best 911s there is, a 87-89 G50 Porsche. However, after many years of service, it is time for a clutch. Maybe, the rubber clutch disc has failed, or the clutch is
More informationMatching Speed to the Road Surface You can't steer or brake a vehicle unless you have traction. Traction is friction between the tires and the road.
Matching Speed to the Road Surface You can't steer or brake a vehicle unless you have traction. Traction is friction between the tires and the road. There are some road conditions that reduce traction
More informationClutching for 2019 Polaris 850 RMK
Clutching for 2019 Polaris 850 RMK Important: The following clutching information has been thoroughly tested and is highly recommended for proper performance and reliability. Primary weights, drive spring
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including
More informationPerformance Installs
Performance Installs FK7-6-101-10 Front-Pipe Back Exhaust Installation Instructions for the 27WON Performance Front-Pipe Back Exhaust on 2017+ Honda Civic Hatchback Sport Written By: Barett Strecker 2018
More informationProduct Information. Installation Tips. Volkswagen - Adjustable Sway Bar End Links. Skill Level 1 - Easy
Product Information Skill Level 1 - Easy Volkswagen - Adjustable Sway Bar End Links Installation Tips Rugged, reliable, red and black. Our ECS Tuning Volkswagen adjustable sway bar end links are built
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you
More informationSpherical MQB Rear Trailing Arm Kit, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3 & TT/TTS
Spherical MQB Rear Trailing Arm Kit, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3 & TT/TTS Supplied Parts: 034Motorsport Spherical MQB Rear Trailing Arm Upgrade (Driver Side) 034Motorsport Spherical
More informationEZ-Glide Wheels Installation Patent Pending Revised 8/23/2011
EZ-Glide Wheels Installation Patent Pending Revised 8/23/2011 Questions: Lakeside Quilt Co. Jack Boersma Toll Free (888) 361-4806 www.lovetoquilt.com Cell (406) 270-4715 sales@lovetoquilt.com Toll Free
More informationTHE HAIRPIN: Talking about sliding sideways,
THE 3.107 MILE Autodromo de la Ciudad de Mexico track hosts the Mexican Grand Prix. It is the highest track in terms of elevation at about 5,000 feet above sea level. This reduces the amount of horsepower
More informationBrake System Rebuilding the brake calipers
Page 1 of 39 Brake System Rebuilding the brake calipers Written by the backyard hack mechanic Sean750 Document history: # 14 Jan 2004 added pictures of rear caliper rebuild kit # 13 Nov 2004 added more
More informationThe Sands Mechanical Museum
The Sands Mechanical Museum How to Change Your Oil It is more difficult to change the oil in a Lotus Elise because the oil plug and filter are difficult to access. They are located behind an access panel.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More information#TL T DOWNPIPES/ INSTALLATION INSTRUCTIONS
#TL100084 4.0T DOWNPIPES/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for on a North American specification RS7, but other models, like the S6 and S8, are similar. When disassembling
More informationRekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +)
Rekluse Motor Sports The ProStart Clutch H-D Sportster (2004 +) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS687 H-D Sportster 195-687 Manual Revision: 111308 Rekluse
More informationAudi B7 A4 2.oT Lightweight Flywheel. Installation Tutorial ES
Audi B7 A4 2.oT Lightweight Flywheel Installation Tutorial ES2739501 Project Preparation Safety Leave the car in neutral. Park the vehicle in a safe, well lit, level area. Open the hood and place protective
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0920 APPLICATION 2007-10 E92/E93 335i/xi with stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationUNDERDOG RACING DEVELOPMENT URD Traction Bar Installation
URD Traction Bar Installation Introduction: UNDERDOG RACING DEVELOPMENT Thank you for choosing the URD Traction Bar for two wheel drive street trucks. More models coming soon! This bar is a true bolt on
More informationSpring manual V3.1 ENGLISH
Spring manual V3.1 ENGLISH HYPERPRO TOOLS, used in this manual: Tool Description Part no. A, B, C Cartridge fork spring removal tool kit HP-T01 D Big Piston Fork end cap socket 45mm HP-T102 E Big Piston
More informationRear Sway Bar for XC90 ( ) 2.5T and T6 ipd mounting kit SBK42
Dedicated to improving vehicle fun, safety & performance Installation Instructions Rear Sway Bar for XC90 (2003-0) 2.5T and T6 ipd mounting kit SBK2 PI-298 08/06 Thank you for purchasing this anti-sway
More informationPowerslot Mustang Rotors (Rear Pair GT/V6) - Installation Instructions
Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) - Installation Instructions The below installation instructions work for the following products: Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) Please
More informationW123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way
W123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way Why do you need to do this?: You need to do this to properly check the internal hydraulic pressure of the transmission, either
More informationRekluse Motor Sports. The z-start Clutch GAS GAS. 200, 250, and strokes. 400 and strokes
Rekluse Motor Sports The z-start Clutch GAS GAS 200, 250, and 300 2-strokes 400 and 450 4-strokes Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS100 Gas Gas z-start
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationCOBB Catback Exhaust
591100 COBB Catback Exhaust 2013 Ford Focus ST Congratulations on your purchase of the COBB Catback Exhaust for your 2013 Ford Focus ST. The following instructions will assist you through your installation
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationMustang 7.5 Limited Slip Differential (28 Spline) V8; V6:
Mustang 7.5 Limited Slip Differential (28 Spline) 79-85 V8; 86-10 V6: Required Tools: Ratchet Wrench Torque Wrench 1/2", 5/16, 3/4", 12mm and 15mm Sockets Lug nut Wrench Dial Indicator Digital Measuring
More informationTooling List 10mm Socket 3 Extension Ratchet Large Jaw Pliers Needle Nose Pliers
Thank you for purchasing! The CorkSport Binary VTA BPV provides features and performance to suit stock cars and on up to big turbo high power setups. The CorkSport Binary VTA BPV holds 50psi, responds
More informationFocus RS Catback
593100 - Focus RS Catback 593100 Focus RS Catback Ford Focus RS 2016-18 Congratulations on your purchase of the COBB Tuning Focus RS Catback Exhaust! The following instructions will assist you through
More informationInstalling LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)
Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationCorkSport Adjustable Front Swaybar ND MX-5
CorkSport Adjustable Front Swaybar 2016+ ND MX-5 Thank you for purchasing the CorkSport Adjustable Front Swaybar. Track tested and racer approved, the CorkSport Front Swaybar is a great compliment to the
More informationRear Strong-Strut. Installation Instructions
Rear Strong-Strut Installation Instructions Please read instructions completely before installing the rear Strong-Strut Forward Installation of the rear Strong-Strut is quite simple and involves the removal
More informationCORKSPORT Power Series Cat Back Exhaust I N S T A L L A T I O N I N S T R U C T I O N S Mazda 6 2.5T PART #: ATK
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Power Series Cat Back Exhaust 2018+ Mazda 6 2.5T PART #: ATK-6-101-12 Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT Power
More informationRekluse Motor Sports. The e-axle KTM. Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.
Rekluse Motor Sports The e-axle 2003 2007 KTM Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.000 RMS 2733 195-2733C Manual Revision: 032207 Rekluse Motor Sports, Inc. 110 E. 43
More information1204AA Ford Mustang Double Adjustable Trailing Arms
1204AA 79-04 Ford Mustang Double Adjustable Trailing Arms Special Tools Required for this Installation - 4 post lift or alignment rack preferable - Air Chisel, Angle Finder (Digital Preferred), Dead blow
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationInstall Guide MQB 1.8T/2.0T Cast Downpipe
Cast Stainless Steel Performance Downpipe, 8V Audi A3/S3 & MkVII Volkswagen Golf/GTI/R Installation Spiciness Rating (Spicy) Installation of your 034Motorsport Cast Downpipe is a complex process. We recommend
More informationAWE Track Edition Touring Edition Exhaust System VA/GV Subaru WRX STI. AWE website here
Thank you for purchasing the AWE Track Edition or Touring Edition Exhaust System for the VA/GV Subaru WRX or STI. For up-to-the-minute fitment information, be sure to visit the Subaru section of the AWE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationHOW TO MODIFY A STOCK DODGE KEGGER INTAKE MANIFOLD
HOW TO MODIFY A STOCK DODGE KEGGER INTAKE MANIFOLD Even though this 3.9L V6 intake manifold is smaller than the 5.2L and 5.9L V8 intake manifolds, the same instructions apply to all 3 engines. If you are
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More information