MODEL G0648 WELDING FUME EXTRACTOR OWNER'S MANUAL

Transcription

1 MODEL G0648 WELDING FUME EXTRACTOR OWNER'S MANUAL WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

2

3 Table of Contents INTRODUCTION... 2 SECTION 1: SAFETY... 6 SECTION 2: CIRCUIT REQUIREMENTS SECTION 3: SETUP SECTION 4: OPERATIONS SECTION 5: ACCESSORIES SECTION 6: MAINTENANCE SECTION 7: SERVICE SECTION 8: WIRING SECTION 9: PARTS WARRANTY AND RETURNS... 53

4 INTRODUCTION Foreword Functional Overview www. grizzly.com Contact Info

5 Identification Figure 1. A. Main Blast Gate: B. Ducting Support System: C. Downdraft Table Port & Blast Gate: D. Slag Drawer: E. Vibrating Filter & HEPA Filter Housing: F. Swivel Caster: G. Main Electrical Box: H. Rolling-Filter Recovery Cabinet: I. Rolling-Filter Supply Cabinet: J. Rotation Joint: K. 6" Ducting System: L. Control Panel: M. Conveyor Cabinet: N. Motor and Fan Storage Cabinet: O. Caster Wheel w/brake: P. Vibrating Filter Dust Drawer:

6 MACHINE DATA SHEET MODEL G0648 WELDING FUME EXTRACTOR Product Dimensions: Shipping Dimensions: Electrical: Motors:

7 Main Specifications: Construction Other Specifications: Features:

8 Safety Instructions for Machinery

9

10 Additional Safety Instructions for Welding Fume Extractors 1. WELDING FUMES. 2. PROTECT BODY FROM ARC BURNS, SPARKS, AND SPATTER. 3. EQUIPMENT MAINTENANCE. 4. WORKING AREA. 5. WELDING IN A CONFINED SPACE CAN BE HAZARDOUS. 6. PREVENT FIRES. 7. EXPERIENCING DIFFICULTIES. Like all machinery there is potential danger when operating this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur. No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment, or poor work results.

11 Meeting Welding Fume Extraction Codes and Standards Welding, cutting, brazing, or soldering of metals can give off poisonous fumes containing zinc, lead, beryllium, cadmium, mercury, fluorine, and hexavalent chromium and others. These fumes typically originate from fluxes, solders, anti-corrosion coatings, pigments, metal fillers, and residual chemicals on the workpiece. This machine is designed to help meet the new welding shop clean air requirements mandated by OSHA. The Model G0648 Welding Fume Extractor is designed to be a part of an overall fume control system. It is NOT designed to serve as a "single-solution for keeping workers safe from all welding fumes. You must contact OSHA to find out how to design and maintain the best overall welding fume control system for your work station or shop. Often, depending on the workspace size, volume of work, type of material to be welded, or other special circumstances, you must use additional safety equipment such as personal air line respirators, hoods, masks, and complete body protection. Contact the organizations below to help you meet welding fume extraction requirements: Occupational Safety and Health Administration OSHA. American Welding Society AWS. American National Standards Institute ANSI. National Institute for Occupational Safety and Health NIOSH. International Agency For Research On Cancer IARC. National Fire Protection Association NFPA, American Conference of Governmental Industrial Hygienists ACGIH.

12 SECTION 2: CIRCUIT REQUIREMENTS 220V 3-Phase Operation Power Connection Figure 2 Serious personal injury could occur if you connect the machine to power before completing the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician! Full Load Amperage Draw Power Supply Circuit Requirements If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician. Extension Cords Figure 2. NOTICE This machine uses sensitive electronics that rely on stable current on all power supply legs. We do not recommend connecting this machine to a phase converter. Ignoring this notice may void warranty. READ ELECTRICAL SAFETY ON PAGE 36!

13 SECTION 3: SETUP Setup Safety Items Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! This machine and its components are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items. Description Qty Unpacking please immediately call Customer Service at (570) for advice. Otherwise, filing a freight claim can be difficult.

14 Inventory Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes. Crate 1: Figure 3 Qty A. B. C. D. E. F. G. Box 2: Figure 4 Qty H. Figure 3. SUFFOCATION HAZARD! Immediately discard all plastic bags and packing materials to eliminate choking/suffocation hazards for children and animals. Figure 4.

15 Hardware Recognition Chart

16 Site Considerations Floor Load Machine Data Sheet 24" MINIMUM OUTPUT CLEARANCE RECYCLED AIR DUCTING WORK ZONE RADIUS OVERHEAD SUCTION CONNECTION ONLY Placement Location Figure 5 220V 3-PHASE LOWER SUCTION CONNECTION ONLY OPTIONAL G0650 WELDING DOWNDRAFT TABLE BASIC WELDING BENCH ACCESSORIES Page 23 DUAL SUCTION CONNECTION Children and visitors may be seriously injured if unsupervised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use. OPTIONAL G0650 WELDING DOWNDRAFT TABLE Figure 5.

17 Ducting Arm Installation To install the ducting arm: 1. Test Run TroubleshootingPage To test run the machine: Note: Position the port so it points in the direction where you will connect ducting to reduce the need for elbows and tees. Having a duct that is longer than 15 feet, using alternating sizes of connections, or using too many elbows or tees will dramatically reduce the available CFM at your downdraft table. When connecting duct to this fume extractor, make sure that you use only fireproof duct and fittings. Refer to the Accessories section on Page 23 for fireproof duct options Maintenance Page 25 Figure 7 3. Figure 6 Figure 7. Figure Figure 7

18 4. Figure Figure 8. OFF Step 11. Figure 7 NOTICE This machine uses sensitive electronics that rely on a good ground. Never unplug the machine while it is running or machine damage can occur. Always use the ON/OFF button or the EMERGENCY STOP button to shut the machine down. When the machine is completely stopped, it then can be unplugged from the power supply. Ignoring this notice will void the warranty.

19 SECTION 4: OPERATIONS Operation Safety General Operation To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Damage to your eyes and lungs could result from using this machine without proper protective gear. Always wear the appropriate respirator and welding helmet fitted with the correct type of eye protection when welding and operating this machine. Loose hair, clothing, or jewelry could get caught in machinery and cause serious personal injury. Keep these items away from moving parts at all times to reduce this risk. To use the machine: NOTICE If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training Control Panel OperationPage 19

20 Note:If the warning lamp/buzzer comes on, it indicates that the rolling-type filter has run out and it is time to replace the roll. 9. Note: After the machine has operated over a minute and then shut down, the FILTER CLEANING lamp will light indicating that as soon as the fan completely stops the vibrating filter will operate in three short durations approximately 3 seconds each

21 Control Panel Operation A. EXHAUSTING TIME min: B. FILTER ROLLING TIME sec: C. FILTER CLEANING: D. FILTER ROLLING: N. FILTER INDICATOR Lamp: O. FILTER INDICATOR Lamp: E. OUT OF FILTER: F. OPERATING: G. SETTING TIME Left Button: EXHAUSTING TIME H. SETTING TIME Right Button: FILTER ROLLING TIME I. CLEANING FILTER MANUAL MODE Button: OFF J. ON/OFF Button: ONOFF K. DOOR LATCH: L. EMERGENCY STOP Button: Figure 9. M. FILTER INDICATOR Buzzer/Lamp:

22 Changing Rolling- Filter Timing To change the rolling-filter timing: Rolling Filter Consumption Chart Page 21 Figure 10 Figure 10 Exhausting Time: Filter Rolling Time: Figure 10..

23 Filter Chart MODEL G0648 ROLLING FILTER CONSUMPTION CHART Rolling Frequency Rolling Duration Filtration Cycle Cycles per Roll Filter Life Span (Approx.) Filter Life Span at 8 Hours/Day (Approx.) Rolling Frequency Rolling Duration Filtration Cycle Cycles per Roll Filter Life Span (Approx.) Filter Life Span at 8 Hours/Day (Approx.) Minutes Seconds Hours:Min:Sec Cycles Hours Days Minutes Seconds Hours:Min:Sec Cycles Hours Days = 0:30:10 x 250 = 126 = = 2:00:10 x 250 = 501 = = 0:30:15 x 167 = 84 = = 2:00:15 x 167 = 335 = = 0:30:20 x 125 = 63 = = 2:00:20 x 125 = 251 = = 0:30:25 x 100 = 51 = = 2:00:25 x 100 = 201 = = 0:30:30 x 83 = 42 = = 2:00:30 x 83 = 167 = = 0:30:40 x 63 = 32 = = 2:00:40 x 63 = 127 = 15.8 Minutes Seconds Hours:Min:Sec Cycles Hours Days Minutes Seconds Hours:Min:Sec Cycles Hours Days = 0:45:10 x 250 = 188 = = 3:00:10 x 250 = 751 = = 0:45:15 x 167 = 126 = = 3:00:15 x 167 = 502 = = 0:45:20 x 125 = 94 = = 3:00:20 x 125 = 376 = = 0:45:25 x 100 = 76 = = 3:00:25 x 100 = 301 = = 0:45:30 x 83 = 63 = = 3:00:30 x 83 = 250 = = 0:45:40 x 63 = 48 = = 3:00:40 x 63 = 190 = 23.7 Minutes Seconds Hours:Min:Sec Cycles Hours Days Minutes Seconds Hours:Min:Sec Cycles Hours Days = 1:00:10 x 250 = 251 = = 4:00:10 x 250 = 1001 = = 1:00:15 x 167 = 168 = = 4:00:15 x 167 = 669 = = 1:00:20 x 125 = 126 = = 4:00:20 x 125 = 501 = = 1:00:25 x 100 = 101 = = 4:00:25 x 100 = 401 = = 1:00:30 x 83 = 84 = = 4:00:30 x 83 = 333 = = 1:00:40 x 63 = 64 = = 4:00:40 x 63 = 253 = 31.6 Rolling Duration (Seconds) Length Rolled (Approx.) Total Paper Length = 9-7/16" / 200' = = 14-3/16" / 200' = = 18-7/8" / 200' = = 23-5/8" / 200' = = 28-3/8" / 200' = = 37-3/4" / 200' = Number of Cycles Per Roll To reduce excessive fume production during related operations and minimize filter consumption, strip all workpiece coatings (paint, varnish, rust, etc.) at least 4" from the location of heat application. To minimize filter waste, do not allow the machine to run when fumes are not being produced. When the rolling filter begins to run low, an alarm will sound, indicating that the filter will soon need to be replaced.

24 SECTION 5: ACCESSORIES T20474 First Layer Stainless Screen T20529 Fourth Layer Filter Figure 11. T20553 Second Layer Aluminum Mesh Figure 14. T20530 Fifth Layer HEPA Filter Figure 12. T20475 Third Layer Paper Filter Roll Figure 15. Figure 13.

25 H5297 6" Welding Fume Collection Kit Steel 6" Elbows G7366 6" 30 G7368 6" 60 G7367 6" 45 G7369 6" 90 G7370 6" 90 Figure 16. H7217 Rigid Flex Hose Figure 18. G0650 Welding Downdraft Table Figure 17. Figure 19.

26 H7786 Auto Darkening Welding Helmet H9748 Leather Jacket Medium H9887 Leather Jacket Large H9888 Leather Jacket X-Large H9746 Leather Knee Pads H9745 Leather Shoe Covers Figure 20. T20505 Welding Respirator with Valve Figure 22. H3157 Deluxe Welding Gloves Figure 21. Figure 23.

27 SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Schedule Lubrication Figure 24 Daily Check/Maintenance: Weekly Check/Maintenance: Figure 24 Monthly Check/Maintenance: Figure 24 Cleaning Figure 24

28 Slag-Screen Cleaning Tools Needed Qty To perform this procedure: Figure 25 Long-Term Storage Figure

29 Rolling-Filter Replacement Tools Needed Qty To perform this procedure: 3. Figure Figure Figure Figure Figure 26. Figure Figure 29 Figure 27. Figure 29.

30 8. Figure 30 Note:For assistance, you can use a couple of pieces of tape to hold the filter paper on the conveyor Figure32 Figure 32. Figure Figure 31 Figure Figure 33 Figure Figure

31 Vibrating Filter Manual Cleaning 4. Figure 35 Tools Needed Qty To perform this procedure: Figure Figure Figure Figure 36 Figure Figure 36. Steps46

32 8. Figure Figure39 9. Figure 37. Figure 38 Figure 38. Figure

33 18. Note: With the top of the spring being held in place by the end of this bolt, compressing and positioning the bottom of the spring into its seat is much easier Figure40 Note: The clearance between the end of the bolt and its seat gives room for the filter to vibrate but not fall out of position. Figure Page32

34 HEPA Filter Manual Cleaning Tools Needed Qty To clean the HEPA filter: Figure42 Figure Figure 41 Figure 42. Figure 41. Figure 43.

35

36 SECTION 7: SERVICE Troubleshooting Motor and Electrical Symptom Possible Cause Possible Solution

37 Operation Symptom Possible Cause Possible Solution

38 SECTION 8: WIRING Electrical Safety Instructions 1. SHOCK HAZARD. 2. CIRCUIT REQUIREMENTS. CIRCUIT REQUIREMENTS Page 10If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician. 3. GROUNDED CIRCUIT. 4. MOTOR WIRING. 5. EXPERIENCING DIFFICULTIES. NOTICE The photos and diagrams included in this section are best viewed in color. You can view these pages in color at WARNING! SHOCK HAZARD! Disconnect power before working on wiring. NOTICE This machine uses sensitive electronics that rely on stable current on all power supply legs. We do not recommend connecting this machine to a phase converter. Ignoring this notice may void warranty. /

39 Wiring Overview Page 40 D Page 42 F 2 Page 42 A 4 6 Page 42 B 7 Page 42 E 5 Page 42 8 Page 38 C 220 VAC 3-PH Page 38 READ ELECTRICAL SAFETY ON PAGE 36!

40 MAIN ELE BOX Main Electrical Box Wiring Figure 45 NEMA PLUG (as recommended ) 3-PHASE 220 VAC G Z X W View this page in color at Figure 51 Figure 50 Figure 44 Figure 42 Figure 44 Figure 48 Figure 49 Figure 49 Figure 50 Page 42 A Page 42 B C Page 42 Figure 46 D Page 40 E Page 42 Figure 47 F Page 42 READ ELECTRICAL SAFETY ON PAGE 36!

41 Main Electrical Box Components Figure 44. Figure 45. Figure 48. Figure 49. Figure 50. Figure 46. Figure 47. Figure 51. READ ELECTRICAL SAFETY ON PAGE 36!

42 Control Panel Wiring MAIN ELE CNTRL View this page in color at Figure 53 Figure 58 Figure 56 Figure 54 Figure 57 Figure 59 Page 38 D READ ELECTRICAL SAFETY ON PAGE 36!

43 Control Panel Electrical Components Figure 55. Figure 52. Figure 56. Figure 57. Figure 59. Figure 53. Figure 54. Figure 58. READ ELECTRICAL SAFETY ON PAGE 36!

44 MAIN ELE MOT Cabinet Wiring Figure 66 Figure 68 View this page in color at Page 38 Figure 69 Figure 64 Figure 62 Page 38 Figure 68 Page 38 Page 38 Figure 67 Figure 69 Figure 63 Page 38 READ ELECTRICAL SAFETY ON PAGE 36!

45 Cabinet Electrical Components Figure 67. Figure 64. Figure 68. Figure 60. Figure 65. Figure 66. Figure 69. Figure 61. Figure 62. Figure 63. Figure 70. READ ELECTRICAL SAFETY ON PAGE 36!

46 SECTION 9: PARTS Main Parts Breakdown G0648

47 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P STAINLESS SCREEN 51 P CONVEYOR ROD 2 P ALUMINUM MESH 555 X 555 X 22MM 52 P TRANSMISSION CHAIN 3 P DRAWER 53 P GUIDE RAIL 4 P SPRING BUCKLE LATCH 54 P3200RS BALL BEARING 3200RS 5 PHTEK23 TAP SCREW #10 X 1/2 55 P CONVEYOR IDLER SHAFT 6 P CABINET 56 P INSULATED END 7 P PLASTIC CAP 57 P GEAR 9T 8 P SPECIAL RETAINING BOLT 3/8" PW07 FLAT WASHER 5/16 9 PN08 HEX NUT 3/ PB07 HEX BOLT 5/16-18 X 3/4 10 P OVAL SEAL 60 P COVER 11 P PLEATED FILTER 600 X 170 X 730MM 61 P STEEL CLAMP 12 P COMPRESSION SPRING 62V2 P V2 MOTOR 12V V P VIBRATION MOTOR 220V 63 P MOTOR BASE 14 PB26 HEX BOLT 1/4-20 X 1-1/2 64 PW06 FLAT WASHER 1/4 15 PB07 HEX BOLT 5/16-18 X 3/4 65 PB05 HEX BOLT 1/4-20 X 3/4 16 P VIBRATION MOTOR BASE A 66 P GEAR 9T 17 P VIBRATION MOTOR BASE B 67 P CHAIN 18 PN05 HEX NUT 1/ P SPECIAL SCREW M6-1 X 6 19 P SPECIAL SCREW 1/4"-24 1/4 69 P SPECIAL BOLT #6-32 X 1 20 P COVER 70 PN12 HEX NUT # PW06 FLAT WASHER 1/4 71 PN05 HEX NUT 1/ PLN02 LOCK NUT 1/ PS01 PHLP HD SCR #10-24 X 1/2 23 PLN03 LOCK NUT 5/ P CHAIN HOUSING A 24 PW07 FLAT WASHER 5/16 74 P CHAIN HOUSING B 25 P ECCENTRIC WHEEL 75 PHTEK8 TAP SCREW #8 X 1/2 26 PLN03 LOCK NUT 5/ P LEFT SIDE DOOR 27 PW07 FLAT WASHER 5/16 77 P HANDLE 28 P SPECIAL HEX BOLT M5-1.5 X P DUST PAN 29 P HINGE 79 PN02 HEX NUT 5/ PN06M HEX NUT M P WING SCREW 31 PHTEK23 TAP SCREW #10 X 1/2 81 P SEAL BOARD 32 P SPRING BUCKLE 82 PHTEK8 TAP SCREW #8 X 1/2 33 P KNOB 83 PW07 FLAT WASHER 5/16 34 PN02 HEX NUT 5/ PB07 HEX BOLT 5/16-18 X 3/4 35 P HEPA FRAME 85 P CASTER W/BRAKE 36 P HEPA FILTER 640 X 890 X 50MM 86 P CASTER W/O BRAKE 37 PN02M HEX NUT M PN02 HEX NUT 5/ PW02 FLAT WASHER 3/8 88 PN08 HEX NUT 3/ P SPECIAL HEX BOLT M X P PRESSURE GAUGE 40 P ALUMINUM HANDLE 400MM 90 PHTEK8 TAP SCREW #8 X 1/2 41 P ROLLING FILTER SWITCH BASE 91 PN08 HEX NUT 3/ PHTEK8 TAP SCREW #8 X 1/2 92 PW02 FLAT WASHER 3/8 43 P ROLLING FILTER SWITCH 93 P BLOWER 44 P FIXED BEARING BASE 94 PB07 HEX BOLT 5/16-18 X 3/4 45 P ROLLING FILTER 95 PW07 FLAT WASHER 5/16 46 P SUPPLY AXLE 96 PB18 HEX BOLT 3/8-16 X 1 47 P SPRING-LOADED BEARING BASE 97 P SPECIAL WASHER 48 PB07 HEX BOLT 5/16-18 X 3/4 98 P IMPELLER 14.5"DIAMETER 49 PW07 FLAT WASHER 5/16 99 PB24 HEX BOLT 3/8-16 X 1-1/4 50 PS23 PHLP HD SCR #8-32 X 1/4

48 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 100 P MOTOR BASE 128 P REDUCER 101 PB07 HEX BOLT 5/16-18 X 3/4 129 PFN07M FLANGE NUT M PW07 FLAT WASHER 5/ PW07 FLAT WASHER 5/ PW02 FLAT WASHER 3/8 131 PB07 HEX BOLT 5/16-18 X 3/4 104 PN08 HEX NUT 3/ P RECOVERY AXLE 105 P MOTOR 2HP 220V 3PH 133 PHTEK8 TAP SCREW #8 X 1/ P FAN COVER 134 P PIPE P MOTOR FAN 135 P SENSOR EYE 106 PN08 HEX NUT 3/ PS01 PHLP HD SCR #10 X 1/2 107 PW02 FLAT WASHER 3/8 137 P RECOVERY BOX 108 PN08 HEX NUT 3/ PHTEK8 TAP SCREW #8 X 1/2 109 P LOWER FRONT DOOR 139 P CONVEYOR SWITCH 110 P HANDLE ROTATION PLATE 140 P ELECTRICAL BOX DOOR 111 P WATERPROOF SWITCH 141 P HINGE 112 P SWITCH HANDLE 142 PHTEK23 TAP SCREW #10 X 1/2 113 P UPPER FRONT DOOR 143 P RIGHT DOOR 114 P SPECIAL HEX BOLT M5-.8 X P GLASS WINDOW X 406.8MM 115 P HINGE 145 P GLASS SEAL 2060MM 116 P COVER 146 P SPECIAL SCREW M5-.8 X PS17 PHLP HD SCR #8-32 X 1/2 147 P HINGE 118 P CHAIN HOUSING C 148 P CONTROL PANEL 119 PS01 PHLP HD SCR #10-24 X 1/2 149 P CONTROL PANEL LOCK 120 P CHAIN 150 P HINGE 121 PN17 HEX NUT 3/ P SPECIAL HEX BOLT M5-.8 X P GEAR 21T 152 P COVER BOARD 123 P GEARED BEARING BASE 153 PHTEK23 TAP SCREW #8 X 1/2 124 PS64M PHLP HD SCR M4-.7 X P DIGITAL CONTROL PANEL 125 PW07 FLAT WASHER 5/ P EMERGENCY STOP SWITCH 126 PB07 HEX BOLT 5/16-18 X 3/4 159 P BUZZER 127 P BASE 163 P WARNING LAMP

49 Blast Gates and Ducting Arm Breakdown Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 200 P HANDLE 275 P BUCKLE 201 PN02 HEX NUT 5/ P GAS SPRING A 202 P HOOD 277 P EXTENSION ARM SUPPORT 203 PW07 FLAT WASHER 5/ P SUPPORT PIN 204 PN02 HEX NUT 5/ P HANDLE 255 P CONNECTOR 280 P ROTATION SHAFT C 256 PB18 HEX BOLT 3/8-16 X P UPPER LEFT ROTATION PLATE 257 PW02 FLAT WASHER 3/8 282 P PIPE SUPPORT BASE 258 PB18 HEX BOLT 3/8-16 X PN02 HEX NUT 5/ PW02 FLAT WASHER 3/8 284 P ROTATION AXLE A 260 P BASE 285 P SPECIAL SCREW 3/8"-18 X 4" 261 P ROTATION PLATE A 286 P UPPER RIGHT ROTATION PLATE 262 PB18 HEX BOLT 3/8-16 X P UPPER PIPE 263 PW02 FLAT WASHER 3/8 288 PB07 HEX BOLT 5/16-18 X 3/4 264 PLW04 LOCK WASHER 3/8 289 PB21 HEX BOLT 3/8-16 X 3/4 265 PN08 HEX NUT 3/ P ROTATION PLATE 266 P ROTATION PLATE B 291 PN02 HEX NUT 5/ V2 P V2 NYLON DUCT 6" X (25 RINGS) V PN08 HEX NUT 3/ P EXTENSION ARM 293 P COLLECTOR BRACKET 269 P SUPPORT PIN A 294V2 P V2 NYLON DUCT 6" X (25 RINGS) V P GAS SPRING B 295 P SUPPORT 271 P LOWER PIPE 296 PHTEK11 TAP SCREW #8 X 3/4 272V2 P V2 NYLON HOSE 6" X (34 RINGS) V V2 P V2 HOSE CLAMP 6-1/2" V PN02 HEX NUT 5/ P INNER HEX SCREW 5/16-18 X P MIDDLE ROTATION PLATE

50 Main Electrical Box Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 300 P CIRCUIT BREAKER ASSEMBLY 309 P SPLIT PHASE CAPACITOR 4UF 125VAC 301 P FUSE HOUSING 310 P SPLIT PHASE CAPACITOR 1UF 400WV AC 302 P FUSE 1AMP 311 P RELAY SHIHLIN TH-P12 5-8A 220V 303 P FUSE 2AMP 312 P TERMINAL BOARD 304 P FUSE 3AMP 313 P SPEED CONTROL RHEOSTAT 305 P PHASE CONTROLLER APR-4 220VAC 314 P RHEOSTAT BOX 306 P TRANSFORMER 220V 315 P LOWER COVER 307 P UPPER COVER 316 P LEFT COVER 308 P CONTACTOR SHIHLIN S-P11 220V

51 Label Placement Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 400 P MACHINE ID LABEL 406 P POISON WARNING LABEL 401 P MODEL ID LABEL 407 PLABEL-14 ELECTRICITY LABEL 402 PLABEL-63 DISCONNECT POWER LABEL 408 P MAGNETIC FILTER TIME CHART 403 P CHANGE PLEATED FILTER LABEL 409 PLABEL-61 RESPIRATOR LABEL 404 P CHANGE HEPA FILTER LABEL 410 P WELDING WARNING LABEL 405 P CHANGE ROLLING FILTER LABEL 411 PLABEL-12A READ MANUAL LABEL Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at or to order new labels.

52 Notes

53

54

55 WARRANTY AND RETURNS

56