MODEL T lb. DUMP CART INSTRUCTIONS

Transcription

1 MODEL T lb. DUMP CART INSTRUCTIONS Specifications SUFFOCATION HAZARD! Immediately discard all plastic bags and packing materials to eliminate choking/suffocation hazards for children and animals. Cart Size (L x W x H)... 59" x " x " Overall Size (L x W x H)... 81" x " x " Wheel Size (H x W)...16" x 5" Total Load Capacity lbs. Net Weight lbs. 1) Never carry people or animals in cart. 2) Do not allow children to use unless supervised by an adult. 3) Do not exceed 500 lb. load capacity. 4) Do not attempt to modify cart to increase load capacity. 5) Do not over-inflate tires. 6) Do not allow cart to become top-heavy, or it could fall over when pulling. 7) Do not park cart on an incline. 8) Do not use cart on roadways. If any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. If you need help with your new item, call our Tech Support at: (570) Inventory (Figure 1) Qty A. Right... 1 B. Support Brace... 1 C. Wheels... 2 D. Left... 1 E. Corner Brackets... 2 F. Rear... 1 G. Front... 1 H. Axle... 1 I. Rear Assembly... 1 J. Side Rails... 2 K. Bottom... 1 L. Axle Supports... 2 M. Tongue... 2 N. Hardware (Not shown) Phillips Head Screws M6-1 x Phillips Head Screws M x Cotter Pin 4 x 65mm... 5 Cotter Pin 11 x 128mm... 8 Lock Nut M Lock Nut M Flat Washer 20mm... 4 A I D F G H M K B J E Figure 1. Inventory. C L COPYRIGHT MAY 2016 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. (FOR MODELS MFD. SINCE 1/16) #JH18141 PRINTED IN CHINA

2 To assemble cart: Assembly 1. Attach support brace to bottom panel using (4) M6-1 x 16 Phillips head screws and (4) M6-1 lock nuts, as shown in Figure Place tongue assembly onto both axle supports and support brace, as shown in Figure 4. Align axle support and tongue assembly holes, and slide axle through. Fully tighten screws from Step 2. Tongue Assembly Support Brace Axle Support Brace Bottom x 4 Figure 2. Attaching support brace to bottom panel. 2. Attach both axle supports to bottom panel using (8) M x 16 Phillips head screws and (8) M lock nuts, as shown in Figure 3. Note: Axle holes in axle supports should align with one another above bottom panel. Do not fully tighten axle support screws to allow alignment of axle supports in next step. Figure 4. Attaching axle to tongue assembly and axle supports. 4. Attach wheels using (1) 20mm flat washer on each side of wheel (see Figure 5), then secure each wheel to axle with (1) cotter pin. Turn cart upright. Flat Washer Axle x 2 Axle Support (1 of 2) Figure 5. Connecting wheel to axle. x 8 Figure 3. Attaching axle supports to bottom panel. -2- T Lb. Dump Cart (Mfd. 01/16)

3 5. Attach corner brackets to left and right side panels using (4) M6-1 x 16 Phillips head screws and (4) M6-1 lock nuts, as shown in Figure Attach both left and right side panels to bottom panel using three cotter pins per side (see Figure 6). 8. Slide rear panel into corner brackets and ensure rear panel pins go into holes in bottom panel to secure rear panel (see Figure 8). Rear x 4 Corner Bracket (1 of 2) x 6 Pins Corner Bracket Side Figure 8. Connecting rear panel to side panels. 9. Insert front and side rails into rail brackets (see Figure 9). Figure 6. Corner brackets and side panels installed on bed. 7. Connect front panel assembly using (4) cotter pins, and use the front panel locks to connect to each side panel, as shown in Figure 7. Side Rails Front Rail Front Lock Cotter Pin x 2 Rail Brackets Figure 9. Inserting front and side rails. Figure 7. Front panel installed. T Lb. Dump Cart (Mfd. 01/16) -3-

4 10. Insert cotter pin into plate behind release bar on trailer tongue (see Figure 10). Note: Pin prevents cart from pivoting up and dumping its load. Remove pin to dump contents. Cotter Pin Operation The Model T709 has a maximum capacity of 500 lbs. and features a tilting dump bed with removable rear panel for easy loading and unloading. The trailer attaches to a tow vehicle using a hitch pin with cotter pin and is not rated for on-road use. Plate Release Bar Positioning roughly 60% of the trailer payload in front (tongue end) of the axle will help maintain better control and handling of the trailer while moving. This also ensures payload will not cause the trailer to pivot uncontrollably when the release handle is pulled. Figure 10. Securing plate with cotter pin. To tilt dump bed: 1. Position rear of trailer in correct location for dumping contents. 2. Remove cotter pin from release plate, and pull release bar with your hand (see Figure 11). Note: Ensure trailer payload is properly positioned with majority of payload situated near front (tongue end) of trailer. Figure 11. Releasing dump bed. 3. If needed, lift trailer bed to help dump payload. 4. Lower trailer bed back into horizontal position, and re-insert cotter pin into release plate. -4- T Lb. Dump Cart (Mfd. 01/16)

5 Accessories T213 Golden Cowhide Gloves T212 Golden Pigskin Gloves T20692 Deluxe Soft Goatskin Gloves Grizzly offers a wide selection of synthetic and leather gloves for all-day comfort in a variety of working conditions. T213 H0605 All Steel Round Head Shovel H0607 Wood Handle Square Head Shovel The D-handle on the H0605 shovel makes trenching or turning the garden soil an easy task. The top edge of the shovel has a rolled edge to make it easier to apply foot pressure for digging. The 14 gauge steel shovel head is swaged and welded onto the steel handle, which is ribbed for strength. Overall length is 38". T20692 T212 This " long H0607 Wood Handle shovel provides extra reach and ergonomic advantage for the taller user. The wooden handle is contoured and is pinned to the head with a steel rivet to avoid twisting. The 14 gauge steel shovel head measures 9" wide by 11" deep with a rolled top edge for a convenient foot hold. H0605 Figure 12. Gloves. H0607 Basic Eye Protection T20451 Kirova Clear Safety Glasses T20452 Kirova Anti-Reflective S. Glasses H7194 Bifocal Safety Glasses 1.5 H7195 Bifocal Safety Glasses 2.0 H7196 Bifocal Safety Glasses 2.5 Figure 14. Shovels. T20452 H7194 T20451 Figure 13. Assortment of basic eye protection. T Lb. Dump Cart (Mfd. 01/16) -5-

6 Maximum Capacity: 900 lbs. Tire Pressure: 25 PSI. Weight: 128 lbs. Mfd. for Grizzly in China Date S/N To reduce risk of serious personal injury when using this machine: 1. Read and understand manual before using this machine. 2. DO NOT exceed cart weight limit of 250 lbs. 3. DO NOT tow cart on public roads or highways. 4. DO NOT exceed 10 mph. Reduce towing speed on rough terrain or hills. 5. Regularly inspect cart for worn or damaged parts. 6. Use cart only for designed purpose. DO NOT modify. 7. DO NOT use this cart to carry people; it is not a toy. 8. Always maintain tire pressure of 25 PSI. 9. Prevent unauthorized use by children; restrict access when unattended. T709 Parts Breakdown & List grizzly.com Specifications 41 MODEL T709 DUMP CART WARNING! REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT BOTTOM PANEL 22 PT HITCH PIN 2 PT WHEEL AXLE SUPPORT 23 PT HITCH PIN BRACKET 3 PT TONGUE 24 PT PANEL LATCH M X 20 4 PT LEFT PANEL 26 PT LATCH CAP PLASTIC 5 PT RIGHT PANEL PT7090 COTTER PIN 4 X 65 HAIR-PIN 6 PT SIDE RAIL 28 PT FLAT WASHER 6MM 7 PT FRONT PANEL 29 PT FLAT WASHER 8MM 8 PT FRONT RAIL 30 PT FLAT WASHER 20MM 9 PT TONGUE RELEASE PEDAL 31 PT PHLP HD SCR M6-1 X PT REAR PANEL 32 PT PHLP HD SCR M4-.7 X PT WHEEL ASSEMBLY 33 PT PHLP HD SCR M X PT LEFT REAR BRACKET 34 PT HEX BOLT M X PT RIGHT REAR BRACKET 35 PT HEX BOLT M6-1 X PT WHEEL AXLE 36 PT LOCK NUT M PT RAIL CLAMP 37 PT LOCK NUT M PT GROMMET 18MM I.D. PLASTIC 38 PT LOCK NUT M PT COTTER PIN 11 X 128 HAIR-PIN 39 PT HEX NUT M PT EXTENSION SPRING 2 X 14 X 140MM 40 PT GRIZZLY.COM LABEL 19 PT SPACER 35L METAL 41 PT MACHINE ID LABEL 20 PT COLLARED PIN M6-1 X 10, 38L 42 PT TOUCH-UP PAINT, GRIZZLY GREEN 21 PT TONGUE SUPPORT -6- T Lb. Dump Cart (Mfd. 01/16)