Disconnect the tie rod from the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - REMOVAL).
|
|
- Gilbert Chambers
- 5 years ago
- Views:
Transcription
1 1 of 7 8/11/2012 6:14 PM 2007 Dodge RAM 1500 Submodel: TRX4 Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Subarticles (LD) 4X2 - IFS - REMOVAL (LD) 4X2 - IFS - REMOVAL (LD) 4X4 - IFS - REMOVAL (HD) 4X2 - IFS - REMOVAL (LD) 4X2 - IFS - INSTALLATION (LD) 4X4 - IFS - INSTALLATION (HD) 4X2 - IFS - INSTALLATION 4X2 (LD) Remove the tire and wheel assembly. Remove the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - REMOVAL). Disconnect the tie rod from the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - REMOVAL). Separate the upper ball joint from the knuckle using remover Remove the lower ball joint nut and separate the lower ball joint from the steering knuckle (1) using puller 8677 (2) (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - REMOVAL).
2 2 of 7 8/11/2012 6:14 PM Press the ball joint from the lower control arm using special tools C-4212 F (PRESS) (1), (DRIVER) (2) and (RECEIVER) (3). 4X4 (LD) Remove the tire and wheel assembly. Remove the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - REMOVAL). Disconnect the tie rod from the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - REMOVAL). Separate the upper ball joint from the knuckle using remover Remove the lower ball joint nut and separate the lower ball joint from the steering knuckle (1) using puller 8677 (2). Remove the half shaft nut. Remove the steering knuckle from the vehicle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - REMOVAL). Move the half shaft to the side and support the half shaft out of the way.
3 OWER BALL JOINT - REMOVAL AND INSTALLATION 3 of 7 8/11/2012 6:14 PM Press the ball joint (3) from the lower control arm using special tools C-4212 F (PRESS) (1), (DRIVER) (2) and (RECEIVER) (4). 4X2 (HD) Remove the tire and wheel assembly. Remove the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - REMOVAL). Disconnect the tie rod from the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - REMOVAL). Remove the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - REMOVAL).
4 4 of 7 8/11/2012 6:14 PM Remove the snap ring (3), from the lower ball joint (2). Press the ball joint (3) from the lower control arm using special tools C-4212 F (PRESS) (1), (RECEIVER) (4) and (DRIVER) (2). 4X2 (LD)
5 OWER BALL JOINT - REMOVAL AND INSTALLATION 5 of 7 8/11/2012 6:14 PM Install the ball joint (4) into the control arm (3) and press in using special tools C-4212 F (press) (1), (driver) (2) and (receiver) (5). Stake the ball joint flange in four evenly spaced places around the ball joint flange, using a punch and hammer. Install the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - INSTALLATION). Install the tie rod end into the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - INSTALLATION). Install the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - INSTALLATION). Install the tire and wheel assembly (Refer to 22 - TIRES/WHEELS/WHEELS - STANDARD PROCEDURE). Check the vehicle ride height (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE). Perform a wheel alignment (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE). 4X4 (LD) Install the ball joint (4) into the control arm (3) and press in using special tools C-4212 F (press) (1), (driver) (5) and (receiver) (2). Stake the ball joint flange in four evenly spaced places around the ball joint flange, using a chisel and hammer. Remove the support for the halfshaft and install into position. Install the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - INSTALLATION).
6 OWER BALL JOINT - REMOVAL AND INSTALLATION 6 of 7 8/11/2012 6:14 PM Install the tie rod end into the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - INSTALLATION). Install the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - INSTALLATION). Install and tighten the halfshaft nut to 251 N m (185 ft. lbs.). Install the tire and wheel assembly (Refer to 22 - TIRES/WHEELS/WHEELS - STANDARD PROCEDURE). Check the vehicle ride height (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE). Perform a wheel alignment (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE). 4X2 (HD) Install the ball joint (3) into the control arm (4) and press in using special tools C-4212 F (press) (1), (driver) (2) and (receiver) (5) Replace the snap ring (3). Install the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - INSTALLATION). Install the tie rod end into the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - INSTALLATION). Install the brake caliper and rotor (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - INSTALLATION). Install the tire and wheel assembly (Refer to 22 - TIRES/WHEELS/WHEELS - STANDARD PROCEDURE). Check the vehicle ride height (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE). Perform a wheel alignment (Refer to 2 - SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE).
7 7 of 7 8/11/2012 6:14 PM Top of Page EBSCO Support Site Privacy Policy Terms of Use Copyright 2010 EBSCO Industries, Inc. All rights reserved EBSCO Publishing Green Initiatives
2006 Dodge RAM of 10 11/15/ :03 PM REMOVAL. Subarticles. Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS
EAR-PINION/RING - REMOVAL AND INSTALLATION 1 of 10 11/15/2012 12:03 PM 2006 Dodge RAM 1500 Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Subarticles GEAR-PINION/RING - REMOVAL GEAR-PINION/RING
More information2003 Ford Focus ZTW SUSPENSION Front - Focus
HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More informationSee SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
More informationLower Arm ( ) Special Service Tools. Removal.
Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More information1 of 5 1/10/2017 5:10 PM
1 of 5 1/10/2017 5:10 PM Shock Module Yoke Replacement ^ Tools Required - J 24319-B Steering Linkage and Tie Rod Puller Removal Procedure 1. Raise and support the vehicle. Refer to Vehicle Lifting. 2.
More informationPage 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
More information2010 Jeep Truck Compass 4WD L4-2.4L
1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front
More information2001 Dodge RAM 3500 PICKUP
1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -
More informationFRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
More informationHalfshaft RH ( )
Page 1 of 7 (47.10.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More informationPage 1 of 7 2003 Chevrolet SILVERADO 1500 Submodel: Engine Type: V8 Liters: 5.3 Fuel Delivery: FI Fuel: GAS Instrument Panel Carrier Replacement Removal Procedure Warning! Refer to Battery Disconnect Caution
More informationWheel Hub: Service and Repair Front
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Wheel Hub: Service and Repair Front Knuckle/Hub Replacement Special Tools Required - Ball joint remover, 28 mm 07MAC-SL00200 - Hub
More informationDIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More information3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17
FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More information2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationORU- Dana 60 Axle Crossover Steering System Bill of Materials, P/N E&F, & E&F
Bill of Materials, P/N 60030-E&F, & 60330-E&F Part# Qty. Description 60030-E Kit (87-97 GM IFS Conversion using '92-'94 Ford Dana 60, 6-8" lift, w/"slider" type caliper mount): 60036-EC 1 Knuckle (slider
More informationTechnical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
More informationPage 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
More informationSUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
More informationcomponents is critical so that the splines are not damaged. NOTE: Never force the hub unit bearing assembly onto the shaft or strike with a hammer.
Automotive TechTips Volume 6 Issue 4 Part 3 of a 3-Part Series Installing a Hub Unit Bearing Assembly and Steering Knuckle Guidelines for Timken continues to lead the hub unit bearing evolution by providing
More informationTitle: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides)
Technical Service BULLETIN September 16, 2002 Title: FRONT BRAKE VIBRATION Models: 00-03 Tundra BR004-02 BRAKES TSB REVISION NOTICE: S March 5, 2004: A torque speification on page 10, step 24, was changed.
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More informationSteering Gear: Service and Repair POWER STEERING GEAR BOX
2003 Kia Truck Sorento V6-3.5L Copyright 2013, ALLDATA 10.52 Page 1 Steering Gear: Service and Repair POWER STEERING GEAR BOX COMPONENTS REMOVAL 1. Drain the power steering fluid. 2. Disconnect the pressure
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2351 2 DROP SPINDLE 2WD ONLY >>> CANNOT USE STOCK WHEELS you MUST use 20 wheels or larger see instructions on pg. 3
More informationIf it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
More informationRear Axle Hub, Bearing, Cup, and/or Seal Replacement
Page 1 of 11 Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools J 8092 Universal Driver Handle - 3/4 inch - 10 J 2222-C Wheel Bearing Nut Wrench J 24426 Wheel Bearing Race Installer - Outer
More informationINSTALLATION INSTRUCTION 88073
INSTALLATION INSTRUCTION 88073 Rev C FOR RANCHO SUSPENSION SYSTEMS RS6572 & RS6573: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More information»Product» Safety Warning
D2201 Installation Instructions 2012-2017 Dodge Ram 1500 4WD 2" Adventure Series Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More informationBrake Pad: Service and Repair Front PADS - BRAKE FRONT
2005 Dodge Truck RAM 3500 4WD Pickup L6-5.9L DSL Turbo VIN C Page 1 Brake Pad: Service and Repair Front PADS - BRAKE FRONT REMOVAL 1. Raise and support vehicle. 2. Remove the wheel and tire assemblies.
More information1997 Mazda MX-5 Miata SUSPENSION Front - Miata
1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over
More information2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement
2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
More information1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
More informationREPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
More informationTechnical Service BULLETIN
Technical Service BULLETIN September 12, 2002 Title: Models: 00 05 Tundra BR004-02 BRAKES TSB REVISION NOTICE: April 4, 2005: Applicable Vehicles has been updated to include 2003 2005 model years. The
More information»Product» Safety Warning
D2300 Installation Instructions 2006-2011 Dodge Ram 1500 4WD 2.5" Adventure Series Suspension System Read and understand all instructions and warnings prior to installation of product and operation of
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationSUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.
More informationSA 8 FRONT AXLE HUB COMPONENTS
SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationWD Dodge Suspension Kit
92137600 02-05 2WD Dodge 1500 6 Suspension Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these
More informationPage 1 of 7 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/19/2000 Hubs, Automatic Lock Refer to Section
More informationPage 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following
More information»Product» Safety Warning
#D2500 Installation Instructions 2002-2005 Dodge Ram 1500 4WD 5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6" Suspension Lift Kit
2012-2015 Dodge Ram 1500 4WD 6" Suspension Lift Kit PRE-INSTALLATION 35015 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 2350 2 DROP SPINDLE 2WD (Must Use 18 Wheels or larger see instructions on Pg.
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More information'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N
4/10/13 '88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N. 10-41888 INSTALLATION INSTRUCTIONS APPLICATION WARNING: Applicable for hub mounted ABS sensor models only. Not for 1992-94
More informationCHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES
1988-1991 CHEVY C1500 2 WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES PARTS LIST: 1 EA. LIFT SPINDLE PASS. SIDE FT1588-7BCP 1 EA. LIFT SPINDLE DRIVER'S SIDE FT1588-7BCD 6 EA.
More informationDetroit Speed, Inc. Rear Cradle Mounts Camaro P/N:
Detroit Speed, Inc. Rear Cradle Mounts 2010-15 Camaro P/N: 041510 Replace the weak, compliant factory rear cradle mounts in your 2010-15 Camaro with Detroit Speed s Solid Rear Cradle Mounts, and completely
More information03 12 REAR AXLE REAR AXLE. End of Toc
LOCATION INDEX....... 1 PRE-INSPECTION................ 1 Wheel Bearing Play Inspection...... 1 (DRUM BRAKE TYPE) REMOVAL/INSTALLATION......... 2 Locknut Removal Note............. 3 Removal Note..................
More informationkit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions
InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950
More informationkit (17% High Range Reduction, 87% Low Range Reduction)
InstalL Instructions suzuki jimny electric/push-button transfer Case gears 304088-3-kit (17% High Range Reduction, 87% Low Range Reduction) kit contents INCLUDED NOTE: If your Jimny has an automatic transmission,
More informationORU- Dana 44 Axle Crossover Steering System Bill of Materials, P/N C&D, & C&D
Bill of Materials, P/N 60130-C&D, & 60230-C&D Part# Qty. Description 60130-C Kit (68-87 GM & 68-91 Blazer/Suburban w/dana 44 or 10-bolt, 6-8" lift w/tie rod facing "nut-up"): 60036-C 1 Knuckle (nut-up)
More informationREMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:
20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationDecember 2004 Distributor/Dealer Service Instructions for: Safety Recall D55 Right Steering Knuckle. Models
December 2004 Distributor/Dealer Service Instructions for: Safety Recall D55 Right Steering Knuckle Models 2005 (JR) Dodge Stratus Sedan and Chrysler Sebring Sedan/Convertible NOTE: This recall applies
More informationSteer Axles. Spicer. Service Manual. AXSM-0070 November Front Drive Steer Axle Model 60
Spicer Steer Axles Service Manual AXSM-0070 November 2017 Front Drive Steer Axle Model 60 General Information The description and specifications contained in this service publication are current at the
More information4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
More informationHydraulic Hub Grappler Kit
655 EISENHOWER DRIVE OWATONNA, MN 55060-0995 USA PHONE: (507) 455-7000 TECH. SERV.: (800) 533-6127 FAX: (800) 955-8329 ORDER ENTRY: (800) 533-6127 FAX: (800) 283-8665 INTERNATIONAL SALES: (507) 455-7223
More informationINSTALLATION INSTRUCTION 88094
INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:
More informationTeam Z Motorsports. K-Member installation instructions
Team Z Motorsports K-Member installation instructions Parts Included: 1-Tubular K-Member Needed Items-Solid Steering Shaft Offset Steering Rack Bushings Optional-Heavy Duty Bolt Kit Tubular Front Lower
More informationFRONT DROP SPINDLES
92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationINSTALLATION INSTRUCTION Rev A
INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationFour-Wheel Alignment ( )
Published: Mar 7, 2005 Four-Wheel Alignment (57.65.04) CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION: Make sure that
More informationDESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.
2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page
More information4 & 6 High Clearance Suspension System. Dodge Ram WD Part#: ,
Part#: 022624, 022402 4 & 6 High Clearance Suspension System Dodge Ram 1500 4WD 2012-2017 Rev. 020918 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com
More informationCHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT
85101 2000-2010 CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT C8510-4 MAIN BOX KIT W/ HARDWARE 1) FRONT X MEMBER 1) REAR X MEMBER 2) TORSION BAR DROPS 1) LEFT BUMP STOP 1) RIGHT BUMP STOP 2) SWAY BAR
More informationINSTALLATION INSTRUCTION 88045
INSTALLATION INSTRUCTION 88045 Rev B FOR RANCHO SUSPENSION SYSTEM RS6545: CHEVROLET SILVERADO READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More information02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT
92122000 92127400 02-10 GM 2500HD / 01-06 1500HD & 07 1500HD CLASSIC 6 2WD SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician
More informationHalfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
More information10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
More informationSTEERING SYSTEM - MANUAL
Article Text ARTICLE BEGINNING 1991-92 STEERING Chrysler Motors/Mitsubishi - Manual Steering - Rack & Pinion Dodge; Colt, Colt Vista, Colt 200, Eagle; Summit Mitsubishi; Eclipse, Mirage, Precis DESCRIPTION
More informationALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front
Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle
More information»Product» Safety Warning
D2201 Installation Instructions 2012-2014 Dodge Ram 1500 4WD 2" Adventure Series Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More information*1333BAG1* 1333BAG DODGE LIFT KIT
921333300 *1333BAG1* 1333BAG1 2012-18 DODGE 1500 4 LIFT KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition
More informationENGINE MECHANICAL PREPARATION SST mm Socket Wrench for 12 Pointed Head Union Nut Wrench 12mm PARTIAL ENGINE ASSY(1ZZ FE)
SST 025 021E001 0901138121 12 mm Socket Wrench for 12 Pointed Head CYLINDER BLOCK(1ZZFE) 0902338200 Union Nut Wrench 12mm 0903200100 Oil Pan Seal Cutter 0920101055 Valve Guide Bushing Remover & Replacer
More informationFRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2
FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3
More informationSUSPENSION AND AXLE SA 1
SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the
More informationPage 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
More informationIMPORTANT!: REVISION FOR VEHICLES EQUIPPED WITH ELECTRIC STEERING RACKS: SEE PG. 8 AND PG. 9 STEPS 26 THROUGH 31. IMPORTANT!:
PRO COMP SUSPENSION IMPORTANT!: REVISION FOR VEHICLES EQUIPPED WITH ELECTRIC STEERING RACKS: SEE PG. 8 AND PG. 9 STEPS 26 THROUGH 31. NOTE: THIS KIT DESIGNED FOR USE WITH FACTORY RAM DRIVE- SHAFT, ANY
More information1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Propeller shaft type 3UJ Front propeller shaft Joint-to-joint length: L 1 mm (in) 633 (24.92) Rear propeller shaft Joint-to-Joint
More information2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.
4-2 [W2A1] SERVICE PROCEDURE 9) Install tie-rod end ball joint on housing knuckle arm. 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.8 (1) Cotter pin (2) Castle nut (3) Tie-rod B4M2214B 10) While depressing brake
More informationCarli Suspension Front Instructions
Carli Suspension Front Instructions 94-08 DODGE 2500-3500 4X4 SUSPENSION SYSTEM Note: Prior to installation, carefully inspect the vehicle=s steering and drive train components. Be sure to check ball joints,
More informationINSTALLATION INSTRUCTION 88554
INSTALLATION INSTRUCTION 88554 Rev B For Rancho Non-Torsion Bar Drop Suspension System RS6554B: GM 2500HD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Ultra Wheels
More informationFront Axle Pinion Seal Replacement
Front Axle Pinion Seal Replacement by Flopster843 10 Apr 2016 The AAM 925 axle used on the front of Dodge Ram trucks is a decent unit, but it does have its flaws. This axle lacks lockout hubs on the front
More informationDISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
More information1NZ-FE ENGINE CONTROL SYSTEM
PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM 1NZ-FE ENGINE CONTROL SYSTEM PREPARATION SST 1 09817-33190 Sensor Socket Wrench 2 PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM RECOMMENDED TOOLS 09082-00040 TOYOTA
More information1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Model All models Propeller shaft type EDJ Front propeller shaft Joint-to-joint length: L 1 mm (in) AT 735.5 (28.96) MT 675.5
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationInstalL Instructions. fj40 knuckle conversion kit. kit contents
InstalL Instructions fj40 knuckle conversion kit 1960-1983 toyota fj40 1960-1983 toyota fj45 304149-1-kit 304150-1-kit 304151-1-kit 304152-1-kit 304153-1-kit 304154-1-kit 304155-1-kit 304156-1-kit 304157-1-kit
More information