REPLACEMENT 1. REMOVE FRONT WHEEL
|
|
|
- Victoria Wilkins
- 6 years ago
- Views:
Transcription
1 3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake tube from the front disc brake caliper assy LH F42731 (c) Remove the 2 bolts and front disc brake caliper assy LH. F REMOVE FRONT DISC 4. REMOVE FRONT AXLE HUB GREASE CAP LH (a) Using a screwdriver and a hammer, remove the front axle hub grease cap LH. Do not damage the axle hub. F REMOVE FRONT AXLE HUB LH NUT (a) Remove the cotter pin and a lock cap. (b) Remove the front axle hub LH nut. F
2 SEPARATE SPEED SENSOR FRONT LH (W/ ABS) (a) Using a hexagon wrench, separate the speed sensor front LH. (b) Disconnect the 2 clamp. (c) Remove the bolt and separate the speed sensor wire harness from the steering knuckle. F SEPARATE FRONT STABILIZER LINK ASSY LH (a) Remove the nut and separate the stabilizer link assy LH from the steering knuckle. HINT: If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud. C SEPARATE TIE ROD END SUBASSY LH (a) Remove the cotter pin and nut. (b) Using, separate the tie rod end subassy LH from the steering knuckle F SEPARATE FRONT SUSPENSION ARM SUBASSY LOWER NO.1 LH (a) Remove the 2 bolts and separate the front suspension arm subassy lower No.1 LH from the steering knuckle. F
3 SEPARATE FRONT SUSPENSION UPPER ARM ASSY LH (a) Remove the cotter pin and nut. (b) Using, separate the steering knuckle from the front suspension upper arm assy LH F REMOVE (a) Using a plastic hammer, separate the front axle hub from the front drive shaft. (b) Remove the front axle hub subassy LH. 12. REMOVE STEERING KNUCKLE LH OIL SEAL (a) Using a screwdriver and hammer, remove the steering knuckle LH oil seal. F REMOVE (a) Remove the 4 bolts and axle hub from the steering knuckle. (b) Remove the Oring from the axle hub. F42759 (c) (d) Fix the front axle hub soft in vise. Using, remove the bearing ( ), ( , , , , , , ) F
4 REMOVE FRONT AXLE HUB LH OIL SEAL (a) Using a screwdriver, remove the front axle hub LH oil seal F INSTALL FRONT AXLE HUB LH OIL SEAL (a) Using a brass bar and a hammer, install the new front axle hub LH oil seal. Do not damage the spacer. F42762 C INSTALL (a) Using and a press, install the new bearing to the front axle hub HINT: Preset the 4 bolts to the new bearing before a press. (b) Apply the MP grease to a new Oring. (c) Install the Oring to the axle hub. Do not damage the speed sensor rotor. (d) Install the dust cover, axle hub to the steering knuckle with the 4 bolts. Torque: 80 N m (816 kgf cm, 59 ft lbf) F INSTALL STEERING KNUCKLE LH OIL SEAL (a) Using and a press, install a new steering knuckle LH oil seal , ( ), F
5 INSTALL Do not damage the speed sensor rotor. Inspect no damage and no foreign matter at the speed sensor rotor. 19. INSTALL FRONT SUSPENSION UPPER ARM ASSY LH (a) Install the front suspension upper arm assy LH with a nut. Torque: 110 N m (1,122 kgf cm, 81 ft lbf) (b) Install a new cotter pin. F INSTALL FRONT SUSPENSION ARM SUB ASSY LOWER NO.1 LH (a) Install the front suspension arm subassy lower No.1 LH with the 2 bolts. Torque: 225 N m (2,294 kgf cm, 166 ft lbf) F INSTALL TIE ROD END SUBASSY LH (a) Install the tie rod end subassy LH with a nut. Torque: 91 N m (928 kgf cm, 67 ft lbf) (b) Install a new cotter pin. F INSTALL FRONT STABILIZER LINK ASSY LH (a) Install the stabilizer link with a nut to the steering knuckle. Torque: 70 N m (714 kgf cm, 52 ft lbf) HINT: If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud. C
6 INSTALL SPEED SENSOR FRONT LH (W/ ABS) (a) Install the speed sensor wire harness to the steering knuckle with a bolt. Torque: 13 N m (133 kgf cm, 10 ft lbf) (b) Connect the 2 clips. (c) Using a hexagon wrench, install the speed sensor with the bolt. Torque: 8.3 N m (85 kgf cm, 73 in lbf) F INSTALL FRONT AXLE HUB LH NUT (a) Install the hub nut. Torque: 235 N m (2,396 kgf cm, 173 ft lbf) (b) Install the adjusting cap and a new cotter pin. F INSPECT BEARING BACKLASH (See page 302 ) 26. INSPECT AXLE HUB DEVIATION (See page 302 ) 27. INSTALL FRONT AXLE HUB GREASE CAP LH 28. INSTALL FRONT DISC 3079
7 INSTALL FRONT DISC BRAKE CALIPER ASSY LH (a) Install the front disc brake caliper assy LH with the 2 bolts. Torque: 123 N m (1,254 kgf cm, 91 ft lbf) F43121 (b) (c) Install the brake tube bracket to the steering knuckle with a bolt. Torque: 29 N m (296 kgf cm, 21 ft lbf) Using, connect the brake tube to the disc brake caliper assy Torque: 15 N m (155 kgf cm, 11 ft lbf) F BLEED BRAKE LINE (See page 324 ) 31. CHECK FLUID LEVEL IN RESERVOIR (See page 324 ) 32. CHECK BRAKE FLUID LEAKAGE (See page 324 ) 33. INSTALL FRONT WHEEL Torque: 112 N m (1,142 kgf cm, 83 ft lbf) 34. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See page 267 ) 35. CHECK ABS SPEED SENSOR SIGNAL (W/ ABS) (See page ) 3080
FRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
Technical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
SHOCK ABSORBER ASSY FRONT LH
2612 REPLACEMENT COMPONENTS: See page 263 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE FRONT WHEEL 260H802 2. SEPARATE FRONT STABILIZER
4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.
OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become
SA 8 FRONT AXLE HUB COMPONENTS
SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing
10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
Page 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
Technical Service BULLETIN
Technical Service BULLETIN September 12, 2002 Title: Models: 00 05 Tundra BR004-02 BRAKES TSB REVISION NOTICE: April 4, 2005: Applicable Vehicles has been updated to include 2003 2005 model years. The
5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.
5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE
AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1
AXLE AXLE SYSTEM 1 AXLE SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of probability of each of the possible causes.
3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17
FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within
REAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front
Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle
REPLACEMENT. 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FAN AND GENERATOR V BELT (See page 14 4)
5540 550JH01 REPLACEMENT HINT: COMPONENTS: See page 5539 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page 5511) SST 0711058060 (0711758080, 0711758090, 0711778050, 0711788060, 0711788070, 0711788080)
REAR DRUM BRAKE (1ZZ FE(FF))
REAR DRUM BRAKE (1ZZFE(FF)) OVERHAUL HINT: Overhaul the RH side by the same procedures as LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID NOTICE: Wash the brake fluid off immediately if it comes into
Title: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides)
Technical Service BULLETIN September 16, 2002 Title: FRONT BRAKE VIBRATION Models: 00-03 Tundra BR004-02 BRAKES TSB REVISION NOTICE: S March 5, 2004: A torque speification on page 10, step 24, was changed.
REMOVE FRONT WHEEL RH
518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER
SUSPENSION AND AXLE SA 1
SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the
Steering Knuckle (See page SA 35)
SA40 SUSPENSION AND AXLE Steering Knuckle (See page SA35) REMOVAL OF STEERING KNUCKLE 1. REMOVE DISC BRAKE CYLINDER AND FRONT AXLE HUB (See page SA36) 2. REMOVE DUST COVER AND OIL SEAL 3. DISCONNECT KNUCKLE
FRONT SUSPENSION SYSTEM
SYSTEM PROBLEM SYMPTOMS TABLE SYSTEM Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary,
POWER STEERING SYSTEM
SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system
Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out)
TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part
See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
). 1. REMOVE FR WIPER ARM RH
5120 OVERHAUL When installing, apply power steering fluid or molybdenum disulfide lithium base grease to the parts indicated by arrows (See page 5117). 1. REMOVE FR WIPER ARM RH (See page 666) 2. REMOVE
SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
OVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.
![2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.](/thumbs/93/112592203.jpg "2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.")
4-2 [W2A1] SERVICE PROCEDURE 9) Install tie-rod end ball joint on housing knuckle arm. 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.8 (1) Cotter pin (2) Castle nut (3) Tie-rod B4M2214B 10) While depressing brake
OVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
OVERHAUL COMPONENTS: See page 3232 Overhaul the RH side by the same procedures with LH side. Two types of brake pad exist; one is with slit and the other without slit. 1. REMOVE REAR WHEEL 2. DRAIN FLUID
SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help
DRAIN BRAKE FLUID NOTICE:
OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE FRONT WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.
Symptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily)
CLUTCH CLUTCH SYSTEM (MTM) PROBLEM SYMPTOMS TABLE HINT: CLUTCH SYSTEM (MTM) Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.
JOINT SHAFT REMOVAL/INSTALLATION
2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed
4. Rear Axle REAR AXLE
REAR AXLE DRIVE SHAFT SYSTEM 4. Rear Axle A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 4) Remove the axle nut using
FRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
TOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
DRAIN BRAKE FLUID NOTICE:
REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.
SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
1997 Mazda MX-5 Miata SUSPENSION Front - Miata
1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over
ALLDATA Online Toyota Camry L4-2.4L (2AZ-FE) - Rear Strut Assembly. Rear Strut Assembly
Page 1 of 11 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Toyota Camry L4-2.4L (2AZ-FE) Conversion Calculator Vehicle
FLOOR SHIFT SHIFT LEVER ASSY (MTM)
4110 FLOOR SHIFT SHIFT LEVER ASSY (MTM) FLOOR SHIFT SHIFT LEVER ASSY (MTM) COMPONENTS 4105U03 Gasoline Engine: Front Floor Heat Insulator No.1 Console Panel Subassy Upper Floor Shift Lever Knob Subassy
1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front
SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front DESCRIPTION An independent front suspension with MacPherson-type struts is used on all models. Miata uses double wishbone design upper and lower control
OVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
REAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 PRECAUTION... 2 REMOVAL AND INSTALLATION... 6 PREPARATION... 3
TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution...2 PREPARATION... 3 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3
If it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
PARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION
78 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 1. DIFFERENTIAL SIDE GEAR (w/ LSD Differential)
DRAIN BRAKE FLUID NOTICE:
OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The
2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
PS 37. POWER STEERING POWER STEERING LINK (for 4WD) REMOVAL
POWER STEERING POWER STEERING LINK (for 4WD) 37 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 3. REMOVE FRONT WHEELS 4. REMOVE NO. 1 ENGINE UNDER
FRONT AXLE 26-1 CONTENTS ON-VEHICLE SERVICE... 5 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 HUB AND KNUCKLE ASSEMBLY...
26-1 FRONT AXLE CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 SPECIAL TOOLS... 3 ON-VEHICLE SERVICE... 5 Wheel Bearing Axial Play Check... 5 Hub bolt replacement... 5 HUB
BR 25 BRAKE HYDRAULIC BRAKE BOOSTER REMOVAL
AKE HYDRAULIC AKE BOOSTER 25 REMOVAL When installing, coat the parts indicated by arrows with lithium soap base glycol grease (See page - 13). As high pressure is applied to the brake actuator tube No.
FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)
BIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30
BIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30 16 KIT PART NUMBER 41002010AA 17 KIT PART NUMBER 41002015AA Installation Guide (Updated 12/01/09) Page 1 of 11 PLEASE READ BEFORE YOU START IN ORDER TO INSTALL THIS
1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION
DESCRIPTION 1998-99 SUSPENSION Rear - Cirrus, Stratus, Breeze & Sebring Convertible Rear suspension uses a short/long arm independent design. See Fig. 1. Each side consists of a strut assembly, upper control
TRANSFER ASSY (VF4AM)
ASSY (VF4AM) 313 ASSY (VF4AM) COMPONENTS 3103202 ATF Level Gauge Transmission Oil Filler Tube Subassy Propeller Shaft Assy 12 (122, 9) ORing Oil Cooler Inlet Tube No.1 and Oil Cooler Outlet Tube No.1 34
1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
TOYOTA COROLLA/MATRIX LOWERING SPRINGS Preparation
Preparation Part Number: PTR40-02080 Kit Contents: Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Vehicle Service Parts (may be required for reassembly) Item
FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions... 2 PREPARATION...
Page 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
STEERING LOCATION INDEX
STEERING LOCATION INDEX 2007 STEERING Power Steering - MX-5 Miata Fig. 1: Identifying Location Of Steering Components AIR BLEEDING CAUTION: Do not turn the steering wheel during the fluid level inspection,
FRONT DROP SPINDLES
92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
Mirrored from:
Mirrored from: http://www.wranglerforum.com/f274/install-synergy-suspension-ball-joints-write-up-147062.html 03-18-2012, 02:43 AM #1 SilverSport Supporting Member WF Supporting Member Install Synergy Suspension
ALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE)
2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) Vehicle» Steering and Suspension» Steering» Steering Gear» Service and Repair» Disassembly and Assembly Part 1 Of 3 Part 2 Of 3 http://alldatapro.com/alldata/pro~v432223842~c41100~r0~od~n/0/101825161/103142888/105946035/110859872/34853741/34864218/34864219/34864308/
PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
Power Steering Pump REMOVAL AND INSTALLATION OF POWER STEERING PUMP
STEERING SR45 Power Steering Pump REMOVAL AND INSTALLATION OF POWER STEERING PUMP Remove and install the parts as shown. SR46 STEERING (MAIN POINTS OF REMOVAL AND INSTALLATION) 1. (RN Series/4WD) DISCONNECT
FRONT AXLE GROUP CONTENTS GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS DRIVE SHAFT ASSEMBLY SPECIAL TOOLS...
26-1 GROUP 26 CONTENTS GENERAL DESCRIPTION 26-2 DIAGNOSIS 26-2 TROUBLESHOOTING STRATEGY 26-2 SYMPTOM CHART 26-3 SYMPTOM PROCEDURES 26-3 SPECIAL TOOLS 26-4 ON-VEHICLE SERVICE 26-6 WHEEL BEARING END PLAY
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
COMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
components is critical so that the splines are not damaged. NOTE: Never force the hub unit bearing assembly onto the shaft or strike with a hammer.
Automotive TechTips Volume 6 Issue 4 Part 3 of a 3-Part Series Installing a Hub Unit Bearing Assembly and Steering Knuckle Guidelines for Timken continues to lead the hub unit bearing evolution by providing
1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3
TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SYMPTOM DIAGNOSIS... 2 NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart...2 PRECAUTION... 3 PRECAUTIONS...
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
PS 60. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) INSPECTION
60 ZK08184E01 INSPECTION 1. INSPECT TIE ROD END SUB-ASSEMBLY (a) Flip the ball joint stud back and forth 5 times as shown in the illustration before installing the nut. (b) Using a torque wrench, turn
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS (NVH)
FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX
FRONT AXLE D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 5 NOISE, VIBRATION AND
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
16. BRAKE SYSTEM 16-0 BRAKE SYSTEM UXV 500
16 BRAKE SYSTEM 16 SERVICE INFORMATION------------------------------------------------ 16-1 TROUBLESHOOTING----------------------------------------------------- 16-2 BRAKE PADS REPLACEMENT-----------------------------------------
1. General Description
1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh
PRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit
2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
FLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX
2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX CHASSIS SECTION This service manual has been prepared to provide SUBARU service personnel with the necessary information and data for the correct maintenance
PRECAUTION TROUBLESHOOTING
STEERING SR1 SR2 PRECAUTION Care must be taken to replace parts properly because they could affect the performance of the steering system and result in a driving hazard. The steering wheel pad has an SRS
REAR AXLE AND SUSPENSION RA 1
REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to