INSTALLATION INSTRUCTION 88073

Size: px
Start display at page:

Download "INSTALLATION INSTRUCTION 88073"

Transcription

1 INSTALLATION INSTRUCTION Rev C FOR RANCHO SUSPENSION SYSTEMS RS6572 & RS6573: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance of your vehicle. It will handle differently, both on and off-road, from a factory equipped passenger car or truck. Failure to drive this vehicle safely may result in serious injury or death to the driver and passengers. ALWAYS WEAR your seat belts, REDUCE your speed, and AVOID sharp turns and other abrupt maneuvers. A. Before installing this system, have the vehicle s alignment and frame checked by a certified technician. The alignment must be within factory specifications and the frame of the vehicle must be sound (no cracks, damage or corrosion). B. Do not install a body lift kit with this suspension system or interchange Rancho components with parts from another manufacturer. Use Rancho shock absorber RS or RS5283 on the front and Rancho shock absorber RS or RS5297 on the rear. C. Do not powdercoat, chrome, cadmium, or zinc plate any of the components in this system. Doing so will render the warranty null and void. To change the appearance of components, enamel paint can be applied over the original coating. D. Each hardware kit in this system contains fasteners of high strength and specific size. Do not mix hardware kits or substitute a fastener of lesser strength. See bolt identification table on page 2. E. Compare the contents of this system with the parts list in these instructions. If any parts are missing, contact the Rancho Technical Department at F. Install all nuts and bolts with a flat washer. When both SAE (small OD) and USS (large OD) washers are used in a fastener assembly, place the USS washer against the slotted hole and the SAE washer against the round hole. G. Apply a drop of thread locking compound to all bolts during installation. CAUTION: Thread locking compound may irritate sensitive skin. Read warning label on container before use.

2 H. Unless otherwise specified, tighten all nuts and bolts to the standard torque specifications shown in the table below. USE A TORQUE WRENCH for accurate measurements. I. Some of the service procedures require the use of special tools designed for specific procedures. The following tools and supplies are recommended for proper installation of this system: Dodge Service Manual Torsion Bar Unloading Tool 8686 Puller 8677 Strap Wrench Dot 3 Brake Fluid Drill motor Hacksaw Assorted Drills: 1/8" through 1/2" Torque Wrench (250 FT-LB capacity) 1/2 Drive Ratchet and Sockets Assorted Combination Wrenches Heavy Duty Jack Stands Wheel Chocks (wooden blocks) Hydraulic Floor Jack Center punch File Hammer Wire Brush (to clean bracket mounting surfaces) Silicone Spray Lubricant Tape Measure Safety Glasses (wear safety glasses at all times) J. It is extremely important to replace torsion bars, CV flanges, and front drive shaft/pinion relationships as original. Be sure to mark left/right, front/rear, and indexing of mating parts before disassembly. A paint marker or light colored nail polish is handy for this. K. Suspension components that use rubber or urethane bushings should be tightened with the vehicle at normal ride height. This will prevent premature failure of the bushing and maintain ride comfort. the beginning of each step when you finish it. Then when you stop during the installation, it will be easier to find where you need to continue from. M. This suspension system was developed using the following wheel & tire combination: 17" x 8.5" wheel with 5 inches of backspacing and a 35" x 12.5" tire. Before installing any other combination, consult your local tire and wheel specialist. N. Important information for the end user is contained in the consumer/installer information pack. If you are installing this system for someone else, place the information pack on the driver s seat. Please include the installation instructions when you finish. O. Thank you for purchasing the best suspension system available. For the best-installed system, follow these instructions. If you do not have the tools or are unsure of your abilities, have this system installed by a certified technician. RANCHO SUSPENSION IS NOT RESPONSIBLE FOR DAMAGE OR FAILURE RESULTING FROM AN IMPROPER OR MODIFIED INSTALLATION L. The required installation time for this system is approximately 5 to 6 hours. Check off the box ( ) at STANDARD BOLT TORQUE & IDENTIFICATION INCH SYSTEM METRIC SYSTEM Bolt Size Grade 5 Grade 8 Bolt Size Class 9.8 Class 10.9 Class /16 15 FT-LB 20 FT-LB M6 5 FT-LB 9 FT-LB 12 FT-LB 3/8 30 FT-LB 35 FT-LB M8 18 FT-LB 23 FT-LB 27 FT-LB 7/16 45 FT-LB 60 FT-LB M10 32 FT-LB 45 FT-LB 50 FT-LB 1/2 65 FT-LB 90 FT-LB M12 55 FT-LB 75 FT-LB 90 FT-LB 9/16 95 FT-LB 130 FT-LB M14 85 FT-LB 120 FT-LB 145 FT-LB 5/8 135 FT-LB 175 FT-LB M FT-LB 165FT-LB 210 FT-LB 3/4 185 FT-LB 280 FT-LB M FT-LB 240FT-LB 290 FT-LB 2

3 PARTS LIST P/N DESCRIPTION QTY Bump Stop Riser Block Brake Hose, Left Brake Hose, Right Aft Brace Bracket Rear Bump Stop Bracket Knuckle, Left Knuckle, Right Front Bump Stop Spacer Subframe Aft Brace Axle Tube Drop Bracket, Front Half Axle Tube Drop Bracket, Back Half Differential Drop Bracket, Left Half Differential Drop Bracket, Right Half Differential Drop Bracket, Aft T Bar Crossmember Drop Bracket Tie Rod End /16-18 x 4.16 x 9.75 U-bolt Brake Hose Gasket Kit 1 Copper Washer U-bolt Hardware Kit 1 9/16-18 Nyloc Nut 8 9/16 USS Washer Rear Bump Stop Hardware Kit Sleeve 4 M x 70 4 M10 Lock Washer Riser Block Pin Kit x.775 Pin Subframe Hardware Kit 1 M x 130 HHCS 2 M Stover Nut 2 M16 Washer 4 Thread Lock End Link Hardware Kit Sleeve 2 3/8-16 x 15.0 HHCS 2 3/8-16 Nyloc Nut 2 Retainer 8 Grommet Axle Tube Hardware Kit 1 M x 65 HHCS 2 P/N DESCRIPTION QTY. M x 70 HHCS 2 M Stover Nut 4 M12 Washer Differential Drop Hardware Kit 1 M x 60 HHCS 2 M x 65 HHCS 2 M Stover Nut 4 M12 Washer Differential Drop Hardware Kit, Aft Sleeve 2 M x 60 HHCS 4 M Stover Nut 4 M12 Washer Aft Brace Hardware Kit Sleeve Bushing 8 9/16-12 x 4.0 HHCS 4 9/16-12 Stover Nut 4 9/16 SAE Washer Torsion Bar Hardware Kit 1 M x 90 HHCS 4 M Stover Nut 4 M12 Washer 8 3/8-16 x 1.0 HHTS OE Skid Plate Hardware Kit Bushing 2 3/8-16 x 1.25 HHCS 4 3/8-16 Stover Nut 4 3/8 SAE Washer 10 M x 40 HHCS 2 3/8-16 x 1.0 HHTS Tie Rod Hardware Kit 1 M Jam Nut Hub Spacer Kit Axle Hub Spacer Front Bump Stop Hardware Kit 1 3/8-16 x 1.25 HHCS 2 3/8 SAE Washer 2 Thread Lock Information Pack Rancho Decal Instructions Consumer/Warranty Information Warning Sticker 1 3

4 ITEM NO. PART NO. DESCRIPTION QUANTITY Bump Stop Riser Block Brake Hose, Left Brake Hose, Right Aft Brace Bracket Rear Bump Stop Bracket Knuckle, Left Knuckle, Right Front Bump Stop Spacer Subframe Subframe Aft Brace Axle Tube Drop Bracket, Front Half Axle Tube Drop Bracket, Back Half Differential Drop Bracket, Left Half Differential Drop Bracket, Right Half Differential Drop Bracket, Aft T Bar Crossmember Drop Bracket Tie Rod End /16-18 x 4.16 x 9.75 U-bolt 4 4

5 VEHICLE PREPARATION FRONT SUSPENSION 2) Support the transfer case skid plate and remove the bolts. See Illustration 3. Remove the skid plate. 1) Park the vehicle on a level surface. Set the parking brake and chock rear wheels. Measure and record the distance from the center of each wheel to the top of the fender opening. See illustration 1. Illustration 1 2) Loosen the front lug and hub nuts before raising the vehicle. 3) Raise the front of the vehicle and support the frame with jackstands. Remove the front wheels and set them aside. SKID PLATE REMOVAL (IF APPLICABLE) 1) Remove the bolts holding the differential skid plate to the front crossmember. See Illustration 2. Slide the skid plate back and remove. TORSION BAR REMOVAL Illustration 3 1) Mark the torsion bars left and right. Make alignment marks on the torsion bars, the lower control arms, and the anchors. 2) Measure and record the length of the exposed threads on the torsion bar adjustment bolts. Left: Right: 3) Install the torsion bar unloading tool (8686). See illustration 4. Increase the tension on the torsion bar until the load is removed from the adjustment bolt. Illustration 2 Illustration 4 5

6 4) Remove the adjusting bolt and swivel nut. See illustration 5. Relieve the tension on the torsion bar and remove the tool. Illustration 7 Illustration 5 5) Remove the torsion bar from the lower control arm. 6) Repeat steps 3 through 5 for the other side. 6) Remove the nuts at the upper and lower ball joints. Disconnect the ball joints from the steering knuckle using puller Remove the steering knuckle. 7) Remove the lower control arm pivot bolts. See illustration 8. Remove the lower control arm. STEERING KNUCKLE & LOWER CONTROL ARM REMOVAL 1) Remove the brake caliper and its mounting bracket as an assembly. Hang the caliper assembly with wire or a tie wrap. 2) Mark the brake rotor left or right. Remove the brake rotor. If applicable, remove the ABS speed sensor from the hub. 3) Remove the axle shaft hub nut. 4) Remove the nut from the outer tie rod stud. Disconnect the tie rod end from the steering knuckle with puller See illustration 6. Illustration 8 8) Repeat steps 1 through 7 for the other side. SUBFRAME INSTALLATION 1) Remove the crossmember that connects the rear frame brackets of the lower control arms. 2) To provide clearance for the differential, cut 1/4" off the inside front corner of the driver side frame bracket. See Illustration 9. Illustration 6 3) With an assistant s help, raise the subframe (176234) up into the lower control arm frame brackets. 5) Remove the front shock absorber and stabilizer link. See illustration 7 6

7 Illustration 9 4) Attach the front of the subframe with the original pivot bolts. Attach the rear of the subframe with the original crossmember bolts. See illustration 10. Tighten the front bolts to 150 ft. lbs and the rear bolts to 75 ft. lbs. Illustration 11 5) Using the hardware from kit , loosely attach differential drop brackets (left half) and (right half) to the differential upper mount and frame bracket. See illustrations 12 and 13. Use the longer bolts on the bottom. Illustration 10 Illustration 12 FRONT DIFFERENTIAL DROP BRACKET INSTALLATION 1) Support the front differential assembly with a jack. 2) Remove the differential housing rear mounting bolts. See illustration 11. 3) Remove the right axle tube mounting bolts. 4) Remove the differential housing upper mounting bolts. Carefully lower the differential assembly about 4 inches. Illustration 13 7

8 6) Using the hardware and sleeves from kit , loosely attach drop bracket to the differential rear mount and frame bracket. See illustration 13. 7) Loosely attach axle tube drop brackets and with the hardware from kit See illustration 14. The wider end of each bracket is attached to the top with the shorter bolts. LOWER CONTROL ARM & STEERING KNUCKLE INSTALLATION 1) Insert the left lower control arm into the subframe pockets on the driver side. Attach the front of the control arm with the hardware from kit Attach the rear of the control arm with the original nut and bolt. NOTE: Do not tighten pivot bolts until vehicle is at normal ride height. 2) Remove the three hub mounting bolts from the driver side steering knuckle. Separate the hub, dust shield and ABS clip (if applicable), from the knuckle. See illustration 16. Illustration 14 8) Tighten all mounting bolts to 70 ft. lbs. 9) Check the clearance between the front drive shaft and the exhaust crossover pipe. See illustration 15. Illustration 16 3) Attach dust shield, hub and ABS clip to new left knuckle Tighten hub bolts to 120 ft. lbs. NOTE: If equipped with ABS brakes, position the speed sensor opening on the hub toward the front of the vehicle. 4) Install axle hub spacer on the driver side axle shaft. See illustration 17. Illustration 15 NOTE: To provide clearance on vehicles equipped with the 5.9-liter engine, the crossover pipe must be reshaped slightly. If you do not have a torch or are unsure of your abilities, remove drive shaft and take vehicle to an exhaust repair shop. If you have the capability, separate drive shaft from differential, heat pipe at the contact point, dimple pipe and reattach drive shaft. 8 Illustration 17

9 5) Support the lower control arm with a jack. Insert axle shaft through hub and install steering knuckle assembly onto the lower ball joint. Install ball joint nut. CAUTION: The ball joint stud taper must be clean and dry before installing into the knuckle. 6) Install the upper ball joint into the knuckle. Install ball joint nut. 7) Tighten the upper ball joint nut to 55 ft. lbs. Tighten the lower ball joint nut to 60 ft. lbs. 8) Raise and support the lower control arm until the spindle to fender height is 26 inches. Tighten the lower control arm pivot bolts to 150 ft. lbs. 9) Attach the stabilizer bar to the lower control arm with end link kit See illustration 18. Illustration 19 2) Cut 1/2 off the end of the tie rod. Remove the jam nut. If necessary, file end of tie rod to remove burrs and clean threads. NOTE: To properly adjust the toe, 3/16 additional tie rod trimming may be necessary on some vehicles. 3) Thread new jam nut from kit then outer tie rod end onto the tie rod. 4) Attach the tie rod end to the steering knuckle with the original nut. Tighten the ball stud nut to 55 ft. lbs. 5) Finger tighten jam nut. Turn the tie rod until three threads are exposed beyond the jam nut. Tighten jam nut to 55 ft. lbs. 6) Repeat steps 1 through 5 for the other side. Illustration 18 10) Install new Rancho shock absorber. 11) Install the axle shaft hub nut and tighten to 185 ft. lbs. 12) Repeat steps 1 through 11 to install the right lower control arm and steering knuckle on the passenger side. TIE ROD END REPLACEMENT 1) Loosen the jam nut on the tie rod assembly. Remove the outer tie rod end. See illustration 19. BRAKE HOSE REPLACEMENT 1) Install the brake rotor. Attach the front caliper to the steering knuckle with the original mounting bolts. Tighten the caliper mounting bolts to 130 ft. lbs. 2) Separate the passenger side front brake line from the brake hose. Plug brake line to prevent brake fluid seepage. NOTE: If the master cylinder becomes empty, then the entire brake system must be bled. Follow manufacturer s recommendations for bleeding the entire system. 3) Remove the bolts holding the brake hose to the frame and caliper. If applicable, separate the ABS wire from the brake hose. See illustration 20. 9

10 3) Apply thread lock and attach the bump stop assembly to the frame bracket with the hardware from kit See illustration 21. To tighten, hold the bolt and turn the spacer with a strap wrench. Illustration 20 4) Remove the brake hose. 5) Attach new right brake hose to the frame. Tighten the frame bolt to 7.5 ft. lbs. 6) Attach the brake line to the hose. Tighten the brake line fitting to 14 ft. lbs. 7) Attach the brake hose to the caliper with the new washers from kit Hold the hose to keep it from moving and tighten the bolt to 20 ft. lbs. 8) Repeat steps 1 through 7 to install left brake hose on the driver side. Illustration 21 AFT BRACE ASSEMBLY & INSTALLATION 1) Lubricate two bushings (553) and one sleeve (457), from kit , with a silicon spray. Press the bushings and sleeve into aft brace See illustration 22. NOTE: If your vehicle does not have ABS brakes, remove the 10mm plug from left brake hose ) Bleed the front brakes as follows: Fill master cylinder reservoir with approved brake fluid. Attach a clear hose to bleeder valve of right front caliper. Immerse other end of hose into glass container partially filled with brake fluid. Open bleeder valve, then have a helper press down on the brake pedal. Close bleeder valve and repeat process until fluid is clear and free of bubbles. Repeat steps for left front caliper. FRONT BUMP STOP & SPACER INSTALLATION CAUTION: Ball joint failure may occur if the new bump stop and spacer are not installed. 1) Pry the original bump stop from the frame bracket below the upper control arm. 2) Apply thread lock and attach new bump stop 1431 to spacer Tighten by hand. 10 Illustration 22 2) Repeat step 1 to install the remaining bushings and sleeves. 3) Loosely attach the angled end of each aft brace assembly to the rear of the subframe (176234) with the hardware from kit Refer to illustration 21. The aft braces should point slightly outward. 4) Remove the inside nut and bolt from each side of the transmission crossmember. See illustration 23.

11 Illustration 23 5) Using the hardware removed in the previous step, loosely attach the aft brace brackets (176149) to the front of the transmission crossmember. Insert the bolt from the front. See illustration 24. Illustration 25 4) Attach drop bracket to the original bracket with the 12mm hardware from kit ) Attach drop bracket to the bottom of the frame rail with the original screws (if applicable) or the self-tapping screws from hardware kit Tighten the 12mm bolts to 75 ft. lbs and the selftapping screws to 30 ft. lbs. 6) Align marks and insert the torsion bar into its respective lower control arm and anchor. Place the anchor in the crossmember. 7) Install the torsion bar loading/unloading tool (8686). Refer back to illustration 4. Increase the tension on the anchor. Illustration 24 6) Attach the aft braces to the brackets with the hardware from kit Tighten the aft brace mounting bolts then the bracket to crossmember bolts to 75 FT-LBS. 8) Reinstall the swivel nut and adjusting bolt. Thread the adjusting bolt in until 1.2 inches of threads are exposed below the swivel nut. Refer back to step 2 of Torsion Bar Removal. Remove the loading/unloading tool. 9) Repeat steps 2 through 8 for other side. TORSION BAR & DROP BRACKET INSTALLATION 1) Remove the mounting bolts from the torsion bar crossmember. Remove the crossmember. 2) If your vehicle did not have a skid plate installed, enlarge the skid plate mounting holes to 5/16. 3) Place torsion bar drop bracket against the bottom of the frame rail and insert it into the original crossmember bracket. See illustration 25. SKID PLATE INSTALLATION (IF APPLICABLE) 1) Attach the rear of the transfer case skid plate to drop brackets with the 3/8 hardware from kit ) Insert the bushings from kit between the skid plate and the transfer case crossmember. See illustration 26. Attach the front of the skid plate to the crossmember with the 8mm bolts from kit

12 9) Install front wheels and lower vehicle to ground. Tighten the lug nuts to 140 ft. lbs. RISER BLOCK INSTALLATION REAR SUSPENSION 1) Chock front wheels. Raise the rear of the vehicle and support the frame with jack stands. Remove the rear wheels. 2) Support the rear axle assembly with a floor jack. Remove both rear shock absorbers. See illustration 28. Do not reuse OEM shock absorbers with this suspension system. Illustration 26 3) With the axle still being supported, remove the U-bolts on the passenger side only. See illustration 28. 3) Tighten all skid plate bolts to 25 ft. lbs. 4) Cut off the raised section on top of the front differential skid plate. See illustration 27. Drill two 3/8 holes as shown in the illustration. Illustration 28 4) Carefully lower the axle about four inches. Do not allow the axle to hang by any hoses or cables. Illustration 27 5) Insert a block pin from kit into the hole in the axle pad. Place the new riser block (15140) on the axle pad. See illustration 29. 5) Place the skid plate against the subframe below the front differential. Push the skid plate back so the upward curve contacts the front of the subframe crossmember. 6) Using the skid plate as a template, mark the mounting hole locations on the bottom of the subframe crossmembers. 7) Remove skid plate and drill a 5/16 hole at each of the marked locations. 8) Attach skid plate to subframe with the selftapping screws from kit Tighten screws to 25 ft. lbs. Illustration 29 12

13 6) Raise the axle assembly until the riser block contacts the helper spring. Be sure to align the hole in the block with the head of the center bolt. 7) Attach the spring to the axle with the NEW U- bolts (740022) and hardware from kit Snug the nuts down but do not tighten. 8) Repeat steps 3 through 7 for the driver side. 9) Install new Rancho shock absorbers BUMP STOP BRACKET INSTALLATION 1) Remove the bump stop from the frame rail above the rear axle. See illustration 30. 4) Install rear wheels and lower vehicle to ground. Tighten lug nuts to 140 ft. lbs. 5) Tighten the U-bolt nuts evenly to 110 ft. lbs. FINAL CHECKS & ADJUSTMENTS 1) Jounce suspension and move the vehicle to normalize ride height. Verify that the front spindle to fender height is 26" and that both sides are equal. If necessary, reinstall tool 8686 and adjust the tension on the torsion bars to correct the height. NOTE: Some vehicles (when driven in 4wd) may experience a slight vibration if the spindle to fender height is set at or above 26". To remove an undesirable vibration, it may be necessary to lower the height to 25". 2) Turn the front wheels completely left then right. Verify adequate tire, wheel, and brake hose clearance. Inspect steering and suspension for tightness and proper operation. 3) With the suspension at maximum extension (full droop), inspect and rotate all axles and drive shafts. Check for binding and proper slip yoke insertion. The slip yoke should be inserted a minimum of one inch into the transfer case and/or transmission. Illustration 30 2) Attach bump stop spacer and the original bump stop to the frame rail with the hardware and sleeves from kit See illustration 31. Tighten the bolts to 45 ft. lbs. 4) Ensure that the vehicle brake system operates correctly. If new brake hoses were installed, verify that each hose allows for full suspension movement. 5) Readjust headlamps. Have vehicle aligned at a certified alignment facility. Recommended Alignment Specifications Caster (degrees): 4.4! 1.0 Camber (degrees): Sum Toe In (degrees):.1!.1 Please retain this publication for future reference. See Important Note N. Illustration 31 3) Repeat steps 1 and 2 for the other side. 13

INSTALLATION INSTRUCTION 88581

INSTALLATION INSTRUCTION 88581 INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension

More information

INSTALLATION INSTRUCTION Rev A

INSTALLATION INSTRUCTION Rev A INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 88088

INSTALLATION INSTRUCTION 88088 INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 89400

INSTALLATION INSTRUCTION 89400 INSTALLATION INSTRUCTION 89400 FOR RANCHO SUSPENSION SYSTEM RS66400B: 2012 RAM 1500 4WD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 88094

INSTALLATION INSTRUCTION 88094 INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:

More information

Suspension System RS6582B

Suspension System RS6582B Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance

More information

INSTALLATION INSTRUCTION 88581

INSTALLATION INSTRUCTION 88581 INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING: This suspension

More information

INSTALLATION INSTRUCTIONS 88518

INSTALLATION INSTRUCTIONS 88518 INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 88051

INSTALLATION INSTRUCTION 88051 INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT

More information

INSTALLATION INSTRUCTION 88148

INSTALLATION INSTRUCTION 88148 INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION

More information

INSTALLATION INSTRUCTION 88146

INSTALLATION INSTRUCTION 88146 INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

INSTALLATION INSTRUCTION 88092

INSTALLATION INSTRUCTION 88092 INSTALLATION INSTRUCTION 88092 FOR RANCHO SUSPENSION SYSTEM RS6592: NISSAN XTERRA & 2WD FRONTIER READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES!

More information

INSTALLATION INSTRUCTION 88578

INSTALLATION INSTRUCTION 88578 INSTALLATION INSTRUCTION 88578 For Rancho Suspension System RS6579B: 4WD Dodge 1500 & 2500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev E IMPORTANT NOTES! WARNING:

More information

Jeep Wrangler (JK) Present

Jeep Wrangler (JK) Present Suspension System RS66110B (3 SPORT SYSTEM w/ Progressive Coil Springs Front & Rear) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT

More information

Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation)

Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation) 88507 Rev G Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation) Jeep Wrangler (JK) 88507 Rev G READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE

More information

INSTALLATION INSTRUCTIONS 88043

INSTALLATION INSTRUCTIONS 88043 INSTALLATION INSTRUCTIONS 88043 FOR RANCHO SUSPENSION SYSTEM RS6543: CHEVROLET K1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev E IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 89450

INSTALLATION INSTRUCTION 89450 INSTALLATION INSTRUCTION 89450 Rancho Suspension System RS66450R7: Fits 2003 2013 4WD Dodge Ram 2500 / 3500 DIESEL MODELS ONLY. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION

More information

Suspension System RS66102B

Suspension System RS66102B 890 Rev A Suspension System RS660B ( SPORT SYSTEM) 0 JEEP MODELS EQUIPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFYCATION KIT RS70003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST CLERANCE ISSUE).

More information

Jeep Wrangler (JK)

Jeep Wrangler (JK) 89109 Rev B Suspension Systems RS66109BR5 and RS66109BR9 2007 2013 Jeep Wrangler 4 Door Sport and Rubicon Models (2 SPORT SYSTEM) Jeep Wrangler (JK) 2007-2013 89109 Rev B READ ALL INSTRUCTIONS THOROUGHLY

More information

INSTALLATION INSTRUCTION 88554

INSTALLATION INSTRUCTION 88554 INSTALLATION INSTRUCTION 88554 Rev B For Rancho Non-Torsion Bar Drop Suspension System RS6554B: GM 2500HD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Ultra Wheels

More information

INSTALLATION INSTRUCTIONS 88511

INSTALLATION INSTRUCTIONS 88511 INSTALLATION INSTRUCTIONS 88511 For Suspension System RS6511: Ford Super Duty Requires coil spring kit RS80117 or RS80119 for a complete installation READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH

More information

INSTALLATION INSTRUCTIONS 88029

INSTALLATION INSTRUCTIONS 88029 INSTALLATION INSTRUCTIONS 88029 FOR SUSPENSION SYSTEMS RS6503: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION REV F IMPORTANT NOTES! WARNING: This

More information

Suspension System RS6525 (B)

Suspension System RS6525 (B) 88525 Rev A Suspension System RS6525 (B) Requires coil spring kit RS80116 (B) or RS80118 (B) for a complete installation Ford Super Duty READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Suspension System RS6509B

Suspension System RS6509B 88509 Rev H Requires the following for a complete installation: Quick disconnect end link kit RS6756B or solid end link kit RS6753B (for the Rubicon) Rancho exhaust kit RS720001 or RS720002 (or equivalent)

More information

Suspension System RS66107 / RS66107B

Suspension System RS66107 / RS66107B 89107 Rev D Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST

More information

Jeep Wrangler (JK) Present

Jeep Wrangler (JK) Present 89107 Rev H Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 88553 Rev A INSTALLATION INSTRUCTIONS For Rancho Suspension System RS66553B: 2017-2011 Ford F250 / F350 Super Duty 4x4 2.5 Leveling Kit (Available in black only. Component in illustrations may be red for

More information

INSTALLATION INSTRUCTIONS 89551

INSTALLATION INSTRUCTIONS 89551 INSTALLATION INSTRUCTIONS 89551 For Rancho Suspension System RS66551B: Ford F250, F350 Super Duty 4x4 DIESEL ONLY (Single Rear Wheels Only With or Without Auxiliary Spring). (WILL NOT WORK ON GAS ENGINES

More information

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms)

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) 89152 Rev B Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) Fits 1997-2006 Jeep Wrangler (TJ / LJ). 89152 Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Suspension System RS6509B

Suspension System RS6509B 88509 Rev D Requires the following for a complete installation: Quick disconnect end link kit RS6756B or solid end link kit RS6753B (for the Rubicon) Rancho exhaust kit RS720001 or RS720002 (or equivalent)

More information

Suspension System RS66104 & RS66104B (4 Crawler System)

Suspension System RS66104 & RS66104B (4 Crawler System) 89104 Rev B Suspension System RS66104 & RS66104B (4 Crawler System) 2012 JEEP MODELS EQUIPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR RANCHO SPORT KIT SUSPENSION SYSTEMS RS6501: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 88045

INSTALLATION INSTRUCTION 88045 INSTALLATION INSTRUCTION 88045 Rev B FOR RANCHO SUSPENSION SYSTEM RS6545: CHEVROLET SILVERADO READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTIONS 8827

INSTALLATION INSTRUCTIONS 8827 INSTALLATION INSTRUCTIONS 8827 FOR SUSPENSION SYSTEM RS6427: CHEVEROLET K1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! A. Before installing

More information

Suspension System RS66105

Suspension System RS66105 89105 Rev D Requires the following for a complete installation: OE frame bracket removal Transmission Crossmember Kit (see below). 2012 and later models equipped with 3.6l V6 engine need exhaust modification

More information

INSTALLATION INSTRUCTIONS 88043

INSTALLATION INSTRUCTIONS 88043 INSTALLATION INSTRUCTIONS 88043 FOR SUSPENSION SYSTEM RS6543: CHEVROLET K1500 Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! A. The vehicle s

More information

INSTALLATION INSTRUCTION 88267

INSTALLATION INSTRUCTION 88267 INSTALLATION INSTRUCTION 88267 FOR RANCHO SUSPENSION SYSTEM RS6267: 2WD CHEVROLET SUBURBAN & TAHOE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES!

More information

INSTALLATION INSTRUCTIONS 88056

INSTALLATION INSTRUCTIONS 88056 INSTALLATION INSTRUCTIONS 88056 FOR RANCHO ROCK CRAWLER SUSPENSION SYSTEM RS6506: JEEP WRANGLER (TJ) Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 89401 Rev D For Rancho Suspension System RS66401B: 2013-2016 RAM 1500 4WD ATTENTION: DOES NOT FIT V6 DIESEL OR VEHICLES EQUIPPED WITH AIR RIDE. Fits OE 17 and up rims ONLY WITH

More information

'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N

'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6 SUSPENSION SYSTEM P/N 4/10/13 '88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N. 10-41888 INSTALLATION INSTRUCTIONS APPLICATION WARNING: Applicable for hub mounted ABS sensor models only. Not for 1992-94

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Rancho Suspension System RS6524B: 2011-2013 Ford F250, F350 Super Duty 4x4 DIESEL ONLY (Single Rear Wheels Only With or Without Auxiliary Spring). (WILL NOT WORK ON GAS ENGINES

More information

INSTALLATION INSTRUCTIONS 88025

INSTALLATION INSTRUCTIONS 88025 INSTALLATION INSTRUCTIONS 88025 REV. A FOR 6469 CHEVROLET K-2500 & 3500 4x4 8-LUG SUSPENSION SYSTEM DO NOT USE A BODY LIFT KIT WITH THIS SUSPENSION SYSTEM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO

More information

INSTALLATION INSTRUCTION 89455

INSTALLATION INSTRUCTION 89455 INSTALLATION INSTRUCTION 89455 Rev A Rancho Suspension Systems RS66455B 2013 2009 4WD Dodge RAM 2500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION WARNING Carefully

More information

02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT

02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT 92122000 92127400 02-10 GM 2500HD / 01-06 1500HD & 07 1500HD CLASSIC 6 2WD SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician

More information

»Product» Safety Warning

»Product» Safety Warning #D2500 Installation Instructions 2002-2005 Dodge Ram 1500 4WD 5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

»Product» Safety Warning

»Product» Safety Warning #F2622 Installation Instructions 1997-2003 Ford F-150 4WD 6" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

6 Suspension System. Dodge Ram WD Part#: ,

6 Suspension System. Dodge Ram WD Part#: , Part#: 022612, 022613 6 Suspension System Dodge Ram 1500 4WD 2002-2005 Rev. 041014 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: tech@bds-suspension.com

More information

INSTALLATION INSTRUCTION Rev A

INSTALLATION INSTRUCTION Rev A INSTALLATION INSTRUCTION RS82100 Rev A Rancho High-Steer Knuckle RS62100 Fits 2016-2007 Jeep Wrangler JK Left and Right Hand Drive Models Requires use of flipped drag link, and 3 or higher lift with a

More information

Dodge Ram Kit

Dodge Ram Kit 92138000 Thank you for choosing Rough Country for your suspension needs. 2002-05 Dodge Ram 1500 4-5.5 Kit Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

Vehicle ride height chart

Vehicle ride height chart Please read Instructions thoroughly and completely before beginning installation. Installation by a certified mechanic is recommended. ReadyLIFT Suspension Inc. is NOT responsible for any damage or failure

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL

More information

These instructions should remain in the vehicle glove box for future reference.

These instructions should remain in the vehicle glove box for future reference. INSTALLATION INSTRUCTION 89118 Rev B Rancho Suspension System RS66118BR5 and RS66118BR9 2 Progressive Sport System Fits 2017-2007 Jeep Wrangler JK 2-Door This suspension system was developed using 255/80R17

More information

»Product» Safety Warning

»Product» Safety Warning #F2402 & F2602 Installation Instructions 2004-2008 Ford F-150 4wd 4-6" Lift System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions

80-96 Ford F150 / Bronco 4WD Class II 4- 6 Suspension Lift Installation Instructions www.skyjacker.com Required Tool List: 80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Floor Jack Jack Stands Measuring

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 89301 Rev D For Rancho Suspension Systems: RS66301B - Fits vehicles equipped with factory steel control arms RS66302B - Fits vehicles equipped with factory aluminum control arms

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 89451 Rev B INSTALLATION INSTRUCTIONS For Rancho Suspension Systems: RS66451R9 2.5 Leveling Kit - DIESEL MODELS ONLY 2014 Dodge Ram 2500 4WD FMVSS 126 Certified Fits OE rims and spare Fits up to: BFG KM2

More information

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

99-06 CHEVY/GM LIFT KIT

99-06 CHEVY/GM LIFT KIT 92127200 99-06 CHEVY/GM 1500 6 LIFT KIT Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these

More information

Read and understand all instructions and warnings prior to installation of system and operation of vehicle.

Read and understand all instructions and warnings prior to installation of system and operation of vehicle. 491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#:022410 Product: 4" Suspension System Application: 2002-2005 Dodge

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 89552 Rev A For Rancho Suspension System RS66552B: 2017-2011 Ford F250 / F350 Super Duty 4x4* *F350 requires additional rear kit RS886503 or RS886502 to be purchased separately.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 89500 Rev G For Rancho Suspension Systems: RS66500B 4½ Lift 2016-2015 Ford F150 4WD FMVSS 126 Certified Requires Rancho shock absorber or strut spacers for installation. Replacement

More information

Installation Instructions

Installation Instructions Installation Instructions 6 Suspension System FTS25005BK / FTS25006BK 2006-2012 Nissan Frontier 2wd/4wd SHORT BED ONLY Tool List: (not included) Floor Jack & Jack Stands Assorted Metric & S.A.E Sockets

More information

INSTALLATION INSTRUCTION Rev B Rancho Upper Control Arm Upgrade Kit RS64903

INSTALLATION INSTRUCTION Rev B Rancho Upper Control Arm Upgrade Kit RS64903 INSTALLATION INSTRUCTION RS89903-1 Rev B Rancho Upper Control Arm Upgrade Kit RS64903 Fits 2016-2003 Toyota 4Runner 4WD Excludes TRD PRO Models READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE

More information

4 Suspension System. Chevy Colorado ZR2 4WD Part#:

4 Suspension System. Chevy Colorado ZR2 4WD Part#: Part#: 021402 4 Suspension System Chevy Colorado ZR2 4WD 2017-18 Rev. 091118 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@ridefox.com Read And Understand All Instructions

More information

Read and understand all instructions and warnings prior to installation of system and operation of vehicle.

Read and understand all instructions and warnings prior to installation of system and operation of vehicle. 102 S. Michigan Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#: 023620 Product: 6" Suspension System Application: 2009-2012 Ford

More information

INSTALLATION INSTRUCTION 89308

INSTALLATION INSTRUCTION 89308 INSTALLATION INSTRUCTION 89308 Rancho Suspension Systems: RS66308B Fits vehicles equipped with factory forged steel upper control arm RS66309B Fits vehicles equipped with factory aluminum or stamped steel

More information

For the 4 lift application we recommend an 18 wheel not to exceed 9 in width with 5 of backspacing/ 0 offset and a 275/65-18 tire.

For the 4 lift application we recommend an 18 wheel not to exceed 9 in width with 5 of backspacing/ 0 offset and a 275/65-18 tire. 921221200F *1221BAG16* 1221BAG16 2015-18 Colorado/ Canyon 4 and 6 Lift Kit Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs

More information

Colorado/ Canyon 4, 5, and 6 Lift Kit

Colorado/ Canyon 4, 5, and 6 Lift Kit *1221BAG3* 1221BAG3 921221200B 2015-16 Colorado/ Canyon 4, 5, and 6 Lift Kit Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs

More information

NOT COMPATIBLE WITH 6.2L

NOT COMPATIBLE WITH 6.2L INSTALLATION INSTRUCTION 89308 Rev D Rancho Suspension Systems: RS66308B Fits vehicles equipped with factory forged steel upper control arm RS66309B Fits vehicles equipped with factory aluminum or stamped

More information

04-08 FORD F150 4 KIT

04-08 FORD F150 4 KIT 9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS DN SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 13 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING PRE-ALIGNMENT

More information

(800) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**

(800) MON-FRI 7AM-5PM PST OR   WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times** IF your ReadyLIFT product has a damaged or missing part, please contact customer service directly. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT

More information

*1274BAG9* 1274BAG GM 4-6 SUSPENSION KIT N2.0. Thank you for choosing Rough Country for your suspension needs A

*1274BAG9* 1274BAG GM 4-6 SUSPENSION KIT N2.0. Thank you for choosing Rough Country for your suspension needs A 92127400A 88-98 GM 4-6 SUSPENSION KIT N2.0 Thank you for choosing Rough Country for your suspension needs. *1274BAG9* 1274BAG9 Rough Country recommends a certified technician installs this system. In addition

More information

Stamped steel upper control arms NOT COMPATIBLE with OE wheels. See page 4 NOT COMPATIBLE WITH 6.2L Engine, or Z95 Magnetic Ride Control

Stamped steel upper control arms NOT COMPATIBLE with OE wheels. See page 4 NOT COMPATIBLE WITH 6.2L Engine, or Z95 Magnetic Ride Control INSTALLATION INSTRUCTION 89308 Rev C Rancho Suspension Systems: RS66308B Fits vehicles equipped with factory forged steel upper control arm RS66309B Fits vehicles equipped with factory aluminum or stamped

More information

2014 F /6 LIFT KIT

2014 F /6 LIFT KIT 92157500 2014 F-150 4 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels.

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels. 2007-2013 7.5" GMC/Chevrolet 1500 4WD Suspension Lift kit PRE-INSTALLATION 15004 2 - Cross-member (Fr/Rr) 2 - Sway Bar Drop Bracket 2 - Knuckle (Dr/Pass) 1 - Driver Diff. Bracket 1 - Passenger Diff. Bracket

More information

Installation Instructions

Installation Instructions Installation Instructions Jeep TJ Long Arm Suspension System 1997-2002 JEEP TJ 4WD 6 1997-2002 JEEP TJ 4WD FTS24002 & BK / FTS24003 & BK / FTS44002 & BK PARTS LIST FTS24002BK Jeep TJ 6' Box Kit 1 FTS24003BK

More information

(877) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**

(877) MON-FRI 7AM-5PM PST OR   WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times** IF your ReadyLIFT product has a damaged or missing part, please contact customer service directly. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT

More information

»Product» Safety Warning

»Product» Safety Warning F2650 Installation Instructions 2017-18 Ford F150 4WD 4-6" Suspension Systems Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT 921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long

More information

(877) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**

(877) MON-FRI 7AM-5PM PST OR   WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times** IF YOUR ReadyLIFT PRODUCT IS MISSING A OR HAS A DAM- AGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT

More information

Warning! READ BEFORE INSTALLING. Notice to Owner, Operator, Dealer and Installer

Warning! READ BEFORE INSTALLING. Notice to Owner, Operator, Dealer and Installer Warning! READ BEFORE INSTALLING Notice to Owner, Operator, Dealer and Installer ReadyLIFT Off Road Suspension s Mid Travel and Long Travel suspension systems and components are designed for OFF ROAD USE

More information

»Product» Safety Warning

»Product» Safety Warning F2634 Installation Instructions 2015 Ford F150 4WD 4-6" Suspension Systems Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

2.5" & 3.5" SUSPENSION SYSTEM JEEP JK WRANGLER 2 & 4 DOOR MODELS

2.5 & 3.5 SUSPENSION SYSTEM JEEP JK WRANGLER 2 & 4 DOOR MODELS 2.5" & 3.5" SUSPENSION SYSTEM 2007-2018 JEEP JK WRANGLER 2 & 4 DOOR MODELS JSPEC2352 www.jksmfg.com jks@ridefox.com 517-278-1226 RV. 100818 GETTING STARTED Read all warnings, instructions, notes and cautions

More information

TOYOTA 4-RUNNER KIT 5 KIT

TOYOTA 4-RUNNER KIT 5 KIT 92173600 1990-1995 TOYOTA 4-RUNNER KIT 5 KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 89452 Rev E For Rancho Suspension Systems: RS66452B 4.5 Radius Arm Drop Bracket Kit - DIESEL MODELS ONLY 2016-2014 Dodge Ram 2500 4WD FMVSS 126 Certified Fits OE 17 and up rims

More information

»Product» Safety Warning

»Product» Safety Warning C2402, C2602 Installation Instructions 2007-2013 Chevy 1/2 Ton 2wd Pickup 4.5", 6.5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of

More information

(800) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**

(800) MON-FRI 7AM-5PM PST OR   WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times** IF YOUR ReadyLIFT PRODUCT IS MISSING A OR HAS A DAM- AGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT

More information

09-UP FORD F150 6 LIFT KIT

09-UP FORD F150 6 LIFT KIT 92159800 09-UP FORD F150 6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

88-98 GM 2-3 SUSPENSION KIT

88-98 GM 2-3 SUSPENSION KIT 92754500 Thank you for choosing Rough Country for your suspension needs. 88-98 GM 2-3 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

2014 F /6 LIFT KIT

2014 F /6 LIFT KIT 92157500 2014 F-150 4 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

*1557BAG12* 1557BAG F /5 /6 LIFT KIT G THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS.

*1557BAG12* 1557BAG F /5 /6 LIFT KIT G THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 2015-18 F-150 4 /5 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 92155700G *1557BAG12* 1557BAG12 Rough Country recommends a certified technician install this system. In addition

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6" Suspension Lift Kit

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6 Suspension Lift Kit 2012-2015 Dodge Ram 1500 4WD 6" Suspension Lift Kit PRE-INSTALLATION 35015 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT

CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT 85101 2000-2010 CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT C8510-4 MAIN BOX KIT W/ HARDWARE 1) FRONT X MEMBER 1) REAR X MEMBER 2) TORSION BAR DROPS 1) LEFT BUMP STOP 1) RIGHT BUMP STOP 2) SWAY BAR

More information

NOT COMPATIBLE WITH 6.2L

NOT COMPATIBLE WITH 6.2L INSTALLATION INSTRUCTION 89301 Rev H Rancho Suspension Systems: RS66301B Fits vehicles equipped with factory forged steel upper control arm RS66302B Fits vehicles equipped with factory aluminum or stamped

More information

(877) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**

(877) MON-FRI 7AM-5PM PST OR   WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times** IF YOUR ReadyLIFT PRODUCT IS MISSING A OR HAS A DAM- AGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT

More information

WD DODGE SUSPENSION LIFT KIT P/N

WD DODGE SUSPENSION LIFT KIT P/N 4/03/03 94-01 4WD DODGE 1500 3 SUSPENSION LIFT KIT P/N 10-46094 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are covered in separate instructions.

More information

»Product» Safety Warning

»Product» Safety Warning RBP-LK343-60, RBP-LK343-60FS RBP-LK343-40, RBP-LK343-40FS Installation Instructions 2015-2017 Ford F150 4WD 4-6" Suspension Systems Read and understand all instructions and warnings prior to installation

More information