Halfshaft RH ( )
|
|
|
- Sherman Goodman
- 5 years ago
- Views:
Transcription
1 Page 1 of 7 ( ) Special Service Tools Ball joint separator (LRT ) Halfshaft remover/replacer /1 (LRT /1) Halfshaft remover/replacer /3 (LRT /3) Retainers - halfshaft remover/replacer /5 (LRT /5) Halfshaft installer adapter
2 Page 2 of 7 Impulse extractor (LRT ) Installer halfshaft oil seal /1 Installer/Guide halfshaft oil seal /2 Removal CAUTION: Angularly Adjusted Roller (AAR) joints, used at the inboard end of some halfshafts have no internal retaining mechanism and can separate. CAUTION: Do not allow halfshafts to hang unsupported at one end or joint damage will occur. CAUTION: Do not store or install halfshafts with joints at maximum articulation or damage may occur to the joint 1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 2. Drain the differential lubricant. For additional information, refer to Differential Draining and Filling ( ) (Section ) 3. Remove the wheels and tires.
3 Page 3 of 7 4. Remove the halfshaft retaining nut. Discard the nut. 5. CAUTION: Use a wrench on the hexagon provided to prevent the ball joint rotating. Disconnect the LH stabilizer bar link. Remove and discard the nut. 6. CAUTION: Use a wrench on the hexagon provided to prevent the ball joint rotating. Remove the stabilizer bar link nut. 7. Release the brake hose bracket from the wheel knuckle. Remove the bolt.
4 Page 4 of 7 8. Loosen the tie -rod end ball joint retaining nut. 9. CAUTION: Ensure the ball joint seal is not damaged. A damaged seal will lead to the premature failure of the joint. Using the special tool, release the tie-rod end ball joint from the wheel knuckle. Discard the nut. 10. CAUTION: To prevent the wheel knuckle falling outwards and disconnection of the halfshaft inner joint, support the wheel knuckle. Loosen the upper arm retaining nut. 11. CAUTION: Ensure the ball joint seal is not damaged. A damaged seal will lead to the premature failure of the joint. Using the special tool, release the upper arm ball joint. Remove and discard the retaining nut.
5 Page 5 of CAUTION: The lower arm ball joint can be damaged by excessive articulation. The wheel knuckle must be fully supported at all times. Do not allow the wheel knuckle to hang on the lower arm. Failure to follow this instruction will result in damage to vehicle. Using the special tools, release the halfshaft from the wheel hub. 13. Release the halfshaft from the wheel knuckle. 14. Position a container to collect the oil spillage. 15. Release the halfshaft from the differential housing. 16. CAUTION: Keep the halfshaft horizontal to avoid damaging the oil seal. Remove the halfshaft. Raise the stabilizer bar to allow removal of the halfshaft. Remove and discard the snap ring.
6 Page 6 of Using the special tools, remove and discard the halfshaft oil seal. Installation 1. Clean the components. 2. Using the special tools, install a new halfshaft oil seal. The halfshaft oil seal protector must be left in place, until the halfshaft is fully installed. 3. NOTE: Do not fully engage the halfshaft until the oil seal protector has been removed. Install the halfshaft. Install the snap ring. Lubricate the seal and the bearing running surfaces with clean axle oil. Make sure the snap ring is fully engaged and retains the halfshaft. Open the halfshaft oil seal protector. 4. NOTE: The oil seal protector is designed to break into two pieces. Remove and discard the halfshaft oil seal protector. 5. CAUTION: The lower arm ball joint can be damaged by excessive articulation. The wheel knuckle must be fully supported at all times. Do not allow the wheel knuckle to hang on the lower arm. Failure to follow this instruction will result in damage to vehicle. Using the special tools, install the halfshaft in the wheel hub.
7 Page 7 of 7 6. Connect the upper arm and wheel knuckle. Install a new nut and tighten to 70 Nm (52 lb.ft). 7. Secure the stabilizer bar link. Install a new nut and tighten to 115 Nm (85 lb.ft). 8. Connect the tie-rod end ball joint. Install a new nut and tighten to 70 Nm (52 lb.ft). 9. Install a new halfshaft retaining nut and lightly tighten. 10. Secure the brake hose retaining bracket to the wheel knuckle. Tighten the bolt to 22 Nm (16 lb.ft). 11. Secure the LH stabilizer link. Install a new nut and tighten to 115 Nm (85 lb.ft). 12. Tighten the new halfshaft retaining nut to 350 Nm (258 lb.ft). Stake the nut to the halfshaft. 13. Install the wheels and tires. Tighten the wheel nuts to 140 Nm (103 lb.ft). 14. CAUTION: Do not fill the differential with lubricant up to the filler plug. The filler plug is only used to fill the differentail with lubricant, and not to act as a level indicator. Fill the differential with the correct amount of lubricant. For additional information, refer to Differential Draining and Filling ( ) (Section )
Lower Arm ( ) Special Service Tools. Removal.
Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
Halfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
REMOVAL AND INSTALLATION > HALFSHAFT
Page 1 of 14 2008 Lincoln MKZ 3.5L Eng Service Manual: REAR DRIVE HALFSHAFTS Print Date: REMOVAL AND INSTALLATION > HALFSHAFT Special Tools Illustration Tool Name Tool Number Front Hub Remover 205-D070
Front Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
2010 Jeep Truck Compass 4WD L4-2.4L
1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front
Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED
Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool
2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement
2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,
Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
Page 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following
FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:
20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag
OVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions
InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950
1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
FRONT AIR SPRING (G271593)
PUBLISHED: 11-MAY-2011 2003.50 XJ RANGE (X350), 204-05 VEHICLE DYNAMIC SUSPENSION FRONT AIR SPRING (G271593) REMOVAL AND INSTALLATION 60.32.08 FRONT AIR SPRING - RENEW ALL DERIVATIVES 0.70 USED WITHINS
Page 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED
Page 1 of 13 2007 GMC Yukon 5.3L Eng Base Service Manual: FRONT SUSPENSION SYSTEM Print Date: REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED J 43631 Ball Joint Separator.
4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT
WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT -YA WU-07 5 x 4.5 -YA WU-08 5 x 5.5 *THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS AND YA WU-08 WILL CHANGE BOLT PATTERN TO 5 ON 5.5*
REMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
REAR SUSPENSION. Wheel Bearing and Wheel Hub. NOTE: All-Wheel Drive (AWD) shown, Front Wheel Drive (FWD) vehicles similar.
2009 Lincoln MKS AWD V6-3.7L Vehicle > Steering and Suspension > Wheels and Tires > Wheel Hub > Service and Repair > Removal and Replacement REAR SUSPENSION Wheel Bearing and Wheel Hub NOTE: All-Wheel
AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS
AXLE SHAFTS - 2.2L 1994 Toyota Celica 1994 DRIVE AXLES Toyota FWD Axle Shafts Celica 2.2L 4 Cyl DESCRIPTION Axle shafts transfer power from transaxle to the front wheels. Axle shaft consists of axle shaft
1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
REMOVAL & INSTALLATION
Page 1 of 6 REMOVAL & INSTALLATION AXLE SHAFTS Removal Raise and support vehicle. Remove front wheels. Remove engine undercovers. Remove cotter pin and lock nut cap. See Fig. 2. Apply brakes and remove
FRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
2004 Explorer/Mountaineer Workshop Manual
Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm
2003 Ford Focus ZTW SUSPENSION Front - Focus
HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper
On-Vehicle Service Hub and Drum Assembly. Remove or Disconnect (Figures 1, 3-5) 1 of 8 11/25/2016 2:47 PM
1 of 8 11/25/2016 2:47 PM On-Vehicle Service Hub and Drum Assembly Remove or Disconnect (Figures 1, 3-5) Tools Required: J-35012 Rear Hub Bearing Nut Wrench J-35013 Rear Hub Remover 1. Remove the drain
1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
Four-Wheel Alignment ( )
Published: Mar 7, 2005 Four-Wheel Alignment (57.65.04) CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION: Make sure that
1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts.
Page 1 of 11 AXLE SHAFTS Removal (Left Side) 1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts. CAUTION: Use a socket to loosen the wheel hub retaining
INDUSTRIES 1631 South Dixie Hwy. Building B Pompano Beach, Florida 33060
1995-2002 Lincoln Continental 38F-30-ASSY 39F-30-ASSY 4-Wheel Full Assembly All Parts are to be Installed by a Certified ASE Technician. Front Conversion: WARNING: BEFORE YOU BEGIN THE REMOVAL OR INSTALLATION,
SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application
2007 Driveline/Axle Wheel Drive Shafts - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Front Wheel Drive Shaft Nut 260
TABLE OF CONTENTS 0 FRONT DRIVE , WHEEL HUB , WHEEL HUB BEARING , KNUCKLE
Subsection 01 (TABLE OF CONTENTS) TABLE OF CONTENTS 0 FRONT DRIVE... 06-02-1 1, WHEEL HUB... 06-02-2 2, WHEEL HUB BEARING... 06-02-2, KNUCKLE... 06-02- FINAL DRIVE... 06-0-1 1, DRIVE CHAIN... 06-0-2 2,
AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
Page 1 of 6 Axle Shaft, Hub, Oil Seal and Outer Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Locknut Wrench T85T-4252-AH Removal 1. Set the parking brake and loosen the eight
DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.
2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page
Detroit Speed, Inc. Rear Cradle Mounts Camaro P/N:
Detroit Speed, Inc. Rear Cradle Mounts 2010-15 Camaro P/N: 041510 Replace the weak, compliant factory rear cradle mounts in your 2010-15 Camaro with Detroit Speed s Solid Rear Cradle Mounts, and completely
Wheel Hub: Service and Repair Front
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Wheel Hub: Service and Repair Front Knuckle/Hub Replacement Special Tools Required - Ball joint remover, 28 mm 07MAC-SL00200 - Hub
See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
REAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type
SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS Specifications........................ 3A-1 General Specifications.................. 3A-1 Fastener Tightening Specifications......... 3A-2 Component Locator...................
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2500 DROPPED FRONT SPINDLE CHEVROLET C / K and G.M.C. SIERRA 1500 / 2500 / 3500 Pick-Ups Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent
TECHNICAL SERVICE BULLETIN. Model Suzuki Swift GA/GS/GT, Sidekick JA/KX/JLX Group Miscellaneous Bulletin No. TS Date December, 1992
!"" #$%!& '(!(()(*+,-. TECHNICAL SERVICE BULLETIN Model 1990-93 Suzuki Swift GA/GS/GT, Sidekick JA/KX/JLX Group Miscellaneous Bulletin No. TS 7-04 11192 Date December, 1992 CONDITION: Change in front housing
SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
FRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front
Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle
10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
Installation Instructions
Instructions Created by an: Revised 7-11-17 LRT 2005-2017 3/1 Leveling/ Lift Kit for Toyota Tacoma by Low Range Off-Road (SKU# LR-LRTACO) Installation Instructions Suggested Tools: CAUTION: Safety glasses
7 Drive Shaft and Axle
7 Drive Shaft and Axle 7.1 General SPECIFICATIONS EITC0100 Drive-shaft Joint type M/T AT Outer B.J. B.J. Inner T.J. T.J. Length (Joint to joint) mm (in.) Left 380 (14.96) 349 (13.74) Right 593 (23.35)
Hydraulic Hub Grappler Kit
655 EISENHOWER DRIVE OWATONNA, MN 55060-0995 USA PHONE: (507) 455-7000 TECH. SERV.: (800) 533-6127 FAX: (800) 955-8329 ORDER ENTRY: (800) 533-6127 FAX: (800) 283-8665 INTERNATIONAL SALES: (507) 455-7223
Page 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
ALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
ON VEHICLE REPAIR AT 27
AUTOMATIC TRANSMISSION (A43D) Onvehicle Repair AT27 ONVEHICLE REPAIR Valve Body REMOVAL OF VALVE BODY 1. CLEAN TRANSMISSION EXTERIOR To prevent contamination, clean the exterior of the transmission. 2.
Wheel end bearing and seal installation guide. Automotive edition Featuring front and rear wheel drive models
Wheel end bearing and seal installation guide Automotive edition Featuring front and rear wheel drive models Introduction Contents The SKF Seal and Bearing lnstallation Guide (SKF #457809) covers the removal
Steering Gear: Service and Repair POWER STEERING GEAR BOX
2003 Kia Truck Sorento V6-3.5L Copyright 2013, ALLDATA 10.52 Page 1 Steering Gear: Service and Repair POWER STEERING GEAR BOX COMPONENTS REMOVAL 1. Drain the power steering fluid. 2. Disconnect the pressure
If it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
CAUTION: Use a rag at the point you are going to pry. because aluminum alloy wheels can be easily damaged.
Front Suspension Knuckle/Hub Replacement NOTE: Use only genuine Honda aluminum wheel weights. Non-genuine aluminum wheel weights may corrode and damage aluminum wheels. Remove the center cap by prying
INSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit
2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line
1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
MANUAL TRANSMISSION CONTENTS
22-1 MANUAL TRANSMISSION CONTENTS GENERAL INFORMATION.................. 2 LUBRICANTS.............................. 2 SEALANT.................................. 2 SPECIAL TOOLS...........................
1 of 9 7/24/2014 9:02 PM
1 of 9 7/24/2014 9:02 PM Four-Wheel Alignment Special Service Tools 204-805 CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION:
1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
nissan patrol birfield kit
nissan patrol birfield kit 300795-kit 1987-1997 nissan patrol gr(y60) 1988-1994 ford maverick 1987-1997 nissan patrol gq 1987-1997 nissan patrol safari 1987-1997 nissan safari kit contents 5356 PINE AVE
Page 1 of 7 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/19/2000 Hubs, Automatic Lock Refer to Section
PRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit
2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
JK 8 Lug Front Locking Hub Conversion Kit
JK 8 Lug Front Locking Hub Conversion Kit Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors Important
Rear Axle Hub, Bearing, Cup, and/or Seal Replacement
Page 1 of 11 Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools J 8092 Universal Driver Handle - 3/4 inch - 10 J 2222-C Wheel Bearing Nut Wrench J 24426 Wheel Bearing Race Installer - Outer
TECHNICAL BULLETIN S /00. S-TYPE Essential Tools Specifications SERVICE DATE 2000 MY-ON S-TYPE MODEL VIN L00001-ON
SERVICE DATE 03/00 TECHNICAL BULLETIN S-TYPE Essential Tools Specifications MODEL VIN S100-01 2000 MY-ON S-TYPE L00001-ON Issue: The Service Tools required for the S-TYPE Sedan are listed below, which
file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...
Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight
Installation Instructions
Instructions Created by an: 2007-Present Toyota Tundra LRT Leveling Lift Kit - 4WD by Low Range Off-Road (SKU# LR-LRTundra) Instructions also apply to 2WD Kits. Installation Instructions Revised 7-11-17
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
Suspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX
FRONT AXLE D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 5 NOISE, VIBRATION AND
2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 3100-3200 3 DROPPED FRONT SPINDLE 73-87 1/2 TON C-10 PICK-UP / 1/2 TON BLAZER
TH!NK neighbor Section 2 Chassis Section 2 Chassis
General Specifications... 2 Torque Specifications... 2 Description and Operation... 4 Wheel Alignment Angles... 4 Brakes... 4 Diagnosis and Testing... 6 Ball Joint Inspection... 6 Wheel Bearing Inspection...
REPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.
DRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
TH!NK neighbor Section 3 Powertrain Section 3 Powertrain
General Specifications... 2 Torque Specifications... 2 Description and Operation... 3 Diagnosis and Testing... 3 Halfshafts... 3 Motor... 3 Motor Controller... 3 Potentiometer... 3 Gearbox... 4 Removal
1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Propeller shaft type 3UJ Front propeller shaft Joint-to-joint length: L 1 mm (in) 633 (24.92) Rear propeller shaft Joint-to-Joint
M-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT
Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
BIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30
BIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30 16 KIT PART NUMBER 41002010AA 17 KIT PART NUMBER 41002015AA Installation Guide (Updated 12/01/09) Page 1 of 11 PLEASE READ BEFORE YOU START IN ORDER TO INSTALL THIS
Suspension. Front Suspension Knuckle/Hub/Wheel Bearing Replacement Upper Arm Replacement Lower Arm Removal/Installation...
Suspension Front and Rear Suspension : Special Tools..18-2 Component Location Index:...18-3. Wheel Alignment.. 18-5 Wheel Bearing End Play Inspection... 18-8 Wheel Runout Inspection... 18-8 Wheel Bolt
CHAPTER 7 FRONT AXLE
CHAPTER 7 FRONT AXLE 1. STRUCTURE FRONT AXLE 1.1 FRONT AXLE STRUCTURE 704W701A (1) Front Bracket (2) Rear Bracket (3) Center Pin (4) Front Axle Support (5) Bevel Gear Case (6) Front Axle Case (7) Front
DIFFERENTIALS & AXLE SHAFTS
DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,
Wheel bearing housing, removing and installing
Page 1 of 17 40-54 Wheel bearing housing, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove bolt for drive axle. WARNING!
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
DRIVE SHAFT & FRONT AXLE
DRIVE SHAFT & FRONT AXLE Return To Main Table of Contents GENERAL... 2 DRIVE SHAFT... 6 HUB AND KNUCKLE... 13 FRONT AXLE... 15 GENERAL GENERAL SPECIFICATIONS Drive shaft Joint type Outer Inner Length (Joint
1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Model All models Propeller shaft type EDJ Front propeller shaft Joint-to-joint length: L 1 mm (in) AT 735.5 (28.96) MT 675.5
REMOVAL AND INSTALLATION
303-03-1 Engine Cooling 303-03-1 REMOVAL AND INSTALLATION Radiator, Cooling Fan and Shroud Special Tool(s) Wrench, Fan Clutch Nut 303-240 (T84T-6312-D) Holding Wrench, Fan Pulley 303-239 (T84T-6312-C)
Repair Manual VW 02T gearbox. INA GearBOX
Repair Manual VW 02T gearbox INA GearBOX Special tools Repair Manual for the VW 02T gearbox Drain the transmission fluid (arrow). Remove the gearbox from the vehicle in accordance with the vehicle manufacturer