ATTENTION. Custom Dynamics Flatz LED Rear Turn Signals Installation Instructions
|
|
- Julianna Blair
- 5 years ago
- Views:
Transcription
1 Custom Dynamics Flatz LED Rear Turn Signals Installation Instructions We thank you for purchasing the Custom Dynamics Flatz LED Assemblies. Our products utilize the latest technology and high quality components to ensure you the most reliable service. We offer one of the best warranty programs in the industry and we back our products with excellent customer support, if you have questions before or during installation of this product please call Custom Dynamics at 1(800) Part Number(s): GEN-FLATZ-RED-B, GEN-FLATZ-RED-C, GEN-FLATZ-SMOKE-B, GEN-FLATZ-SMOKE-C Package Contents: - Flatz LED Rear Turn Signals (pair) - 3M Tape Primer Ampule (1) - PTA2022 Posi-Tap Connectors (4) - 4 Tie Wraps (10) Installation 1. Select location for mounting the Flatz make sure that you have enough flat surface to properly adhere to. Make sure surface in clean and free of dirt and contaminates. If mounting on Street Glide Filler Panels, See Supplemental installation on page Using the included 3M Promoter Ampule, apply to the surface area that LEDs will adhere to, allow 4-5 minutes to dry. 3. Test fit the units in the desired location, mark the location of the wiring, then drill at the location with 1/8 drill bit. Or mount unit at an edge and wrap wires around edge. 4. Uncoil the wires and feed through hole or around edge. 5. Remove a few inches of the red backing from the tape on the end with the wire, fold towards you for enough to grab onto to remove the rest in a minute. Attach the end of the Flatz to the surface while guiding the wire through. Make sure units is the desired place. Slowly pull on the red backing, removing it all the way. Apply light pressure to the unit to ensure go contact with the surface. ATTENTION Please read all Information below before Installation Important: It is recommended to perform this installation in a controlled environment of 65 degrees F or higher and allow 24 hours for the tape to bond completely before washing or operating the vehicle. Note: When removing turn signals on some vehicles and switching to LEDs a fast flash from the turn signals may occur. A load equalizer or signal stabilizer will be required for normal flash rate. Contact us for details. Important: Cap off any unused wires to prevent shorting. Disclaimer: This product is designed and intended for use as auxiliary lighting on motorcycles only. This product is NOT intended to replace any original equipment lighting installed on the motorcycle and should not be used for that purpose. This product must be wired such that it does not interfere with any original equipment lighting. 6. Bring wiring to the desired area of the vehicle s wiring harness, make sure that all of the functions, run, brake, turn, and ground are present before proceeding. Using a meter or test light is a good idea to confirm which wires carry each function. 7. Use the diagram on the following pages towire the Flatz into the harness with the included Posi-Tap Connectors. For instructions on using Connectors see Figure Right. 8. Secure wires with the included tie wraps, make sure wiring will not come in contact with moving parts or in an area with high heat. Also take care that wires will not get pinched or frayed.
2 Installation Instructions - Page 2 Installation Tip for HD Street Glide Filler Panels Use the Fender edge line and keep a fingers width between it and the FLATZ housing for optimum level and surface adhesion. The photo above shows the ideal placement for the FLATZ LEDs. Due to the curvature of the filler panel, keeping the unit within a fingers width of the fender line maximizes the surface area the unit will adhere to. Note that in this installation fitment, not 100% of the adhesive surface of the Flatz will make contact with the filler panel due to this curvature. There will sufficient surface area when the LED is affixed in the area shown.
3 Red = Left Brake/Turn Yellow = Low intensity Run Installation Instructions - Page 3 Typical Installation on Most Vehicles Vehicle Constant Power [ + ] Vehicle Turn or Harness [ - ] Vehicle Brake/L Turn or both [ + ] Vehicle Brake/R Turn or both [ + ] Included Posi-Tap Connectors Red = Right Brake/Turn = Yellow Red Low Intensity High Intensity When using Flatz on vehicles with aftermarket Run/brake/turn module installed - the low intensity circuit will not be used and should be capped off to prevent shorting. When using Flatz with only one function, the unused wire should be capped off to prevent shorting.
4 Installation Instructions - Page 4 Flatz as Run/Brake/Turn on Bike with After Market Run-Brake-Turn Controller (Controller Sold Separately) Left Output Typically Purple Ou Input Side RBT Controller Right Output Typically Brown Bike Typically Yellow - Not used Yellow - Not used = Connection Flatz as Run/Brake/Turn on Street Glide & Road Glide Output Side, Right Side of fender, remove back cover of Tri-bar, for Access, Use Test Light to Determine what Purple is left and what is Right Input Side-Left Yellow Tri-Bar Fender Tip Light Output Side-Right Purple Turn Purple Turn Blue Running Red
5 Installation Instructions - Page 5 Flatz as Run/Brake/Turn on H-D Street Glide/Touring Custom Dynamics MPR-BCM Adapter (Sold Separately) Wire Harness Color/Functions (note: wiring without MPR see next Page) Blue Red Brown Purple Orange Running Brake R Turn/Brake L Turn/Brake Aux Power This diagram demonstrates run/brake/turn with the MPR-BCM adapter converters (sold separately). Other Functions available: Brake/Turn - Using the MPR-BCM and Not connecting the Yellow wire, (wire should be capped off to prevent shorting) Run/Brake - Using the BCM and dual converters connecting the orange wire from the dual converter to the Blue wire, and the red wire from the dual converter to the Red wire in the MPR H-D motorcycles do not need a Load equalizer when removing stock turn signals.
6 Installation Instructions - Page 6 Flatz as Run/Brake/Turn on H-D Street Glide/Touring Stock Wire Harness Color/Functions (note: only when not using MPR harness adapter) Blue Blue/Red Blue/Brown Blue/Purple Red/Yellow Running Brake R Turn/Brake L Turn/Brake Accy. Power
Custom Dynamics Plasma Rods Installation Instructions
Custom Dynamics Plasma Rods Installation Instructions We thank you for purchasing the Custom Dynamics LED Plasma Rods! Our products utilize the latest technology and high quality components to ensure you
More informationCustom Dynamics Plasma Rods Installation Instructions
Custom Dynamics Plasma Rods Installation Instructions We thank you for purchasing the Custom Dynamics LED Plasma Rods! Our products utilize the latest technology and high quality components to ensure you
More informationCustom Dynamics LED Plugz Installation Instructions
Custom Dynamics LED Plugz Installation Instructions We thank you for purchasing the Custom Dynamics LED Plugz! Our products utilize the latest technology and high quality components to ensure you the brightest,
More informationCustom Dynamics LED Plugz Installation Instructions
Custom Dynamics LED Plugz Installation Instructions We thank you for purchasing the Custom Dynamics LED Plugz! Our products utilize the latest technology and high quality components to ensure you the brightest,
More informationCustom Dynamics Plasma Rods Installation Instructions
Custom Dynamics Plasma Rods Installation Instructions We thank you for purchasing the Custom Dynamics LED Plasma Rods! Our products utilize the latest technology and high quality components to ensure you
More informationCustom Dynamics TruFLEX Installation Instructions
Custom Dynamics TruFLEX Installation Instructions We thank you for purchasing the Custom Dynamics TruFLEX LEDs. Our products utilize the latest technology and high quality components to ensure you the
More informationATTENTION. Installation Instructions. Custom Dynamics Windshield Trim LED Turn Signals. Installation. Part Number: CD-WT-14-B, CD-WT-14-C
Custom Dynamics Windshield Trim LED Turn Signals Installation Instructions We thank you for purchasing the Custom Dynamics Windshield Trim LED turn signals. Our products utilize the latest technology and
More informationATTENTION. Custom Dynamics Smart Triple Play Installation Instructions. Package Contents: - Smart Triple Play Module (1) - Instructions
Custom Dynamics Smart Triple Play Installation Instructions We thank you for purchasing the Custom Dynamics Smart Triple Play. Our products utilize the latest technology and high quality components to
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationCustom Dynamics LED Tri-Bar Fender Tip Installation Instructions
Custom Dynamics LED Tri-Bar Fender Tip Installation Instructions We thank you for purchasing the Custom Dynamics LED Tri-Bar Fender Tip! Our products utilize the latest technology and high quality components
More informationRUN/BRAKE/TURN AUXILIARY LIGHTS J
RUN/BRAKE/TURN AUXILIARY LIGHTS J06236 2018-05-31 GENERAL Kit Numbers 67800589A, 69202276 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harleydavidson.com
More informationStep 1 : Starting the installation
Installation Instructions for GM Remote Start w/ INTSL Interface Pre-wired Review the remote start installation manual for safety instructions! Overview Your kit consists of two modules a remote start
More informationCustom Dynamics Spyder Stingerz Installation Instructions
Custom Dynamics Spyder Stingerz Installation Instructions We thank you for purchasing the Custom Dynamics Stingerz! Our products utilize the latest technology and high quality components to ensure you
More informationXK8 / XKR Navigation to Triple Gauge Cluster Conversion Harness Kit. Instructions
XK8 / XKR Navigation to Triple Gauge Cluster Conversion Harness Kit Instructions Kit Contents: 1 - Gauge Cluster Wiring Harness 1 - Posi-Tap connector 4-4" Tie-Wraps 1- Cable pulling tool (shipped pre-applied
More informationCHEVY MONTE CARLO. Two Panel Sequential LED Tail Light Kit Installation Guide
1986-88 CHEVY MONTE CARLO Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal Kit 1 adhesive tube
More informationCHEVORLET IMPALA
1962-64 CHEVORLET IMPALA Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 deck lid harness 4 grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationELECTRIC REVERSE Current. Harley-Davidson Sportster. Installation Instructions
By ELECTRIC REVERSE 2004 - Current Harley-Davidson Sportster Installation Instructions California Sidecar Parts & Technical Support 434.263.8866 Warnings and considerations: 1. Disclaimer - These instructions
More informationR-SE JK 4 DOOR Step Slider Install Instructions. *If any parts listed are missing or damages please call prior to install.
R-SE JK 4 DOOR Step Slider Install Instructions Parts List: 1 Divers side slider assembly 1 Passenger side slider assembly 1 wiring harness 1 control box 2 spacers 2 LED lights (optional) 10 SS Button
More informationParts List. Please be sure to read our instructions thoroughly before attempting installation. D2/G2 Parts List. D31/G31 Parts List.
Parts List Please be sure to read our instructions thoroughly before attempting installation. D2/G2 Parts List D31/G31 Parts List Page 2 1 Step 1: Bike Preparation Step 1: Bike Preparation There are two
More informationELECTRIC REVERSE Installation Instructions
BY 1999 - Current FLHT Series Harley-Davidson ELECTRIC REVERSE Installation Instructions REVISED 1-2016 California Sidecar Parts & Technical Support 434.263.8866 Warnings and considerations: 1. Disclaimer
More informationEnglish. Fitting Instructions: Trophy and Trophy SE A of 12. Parts Supplied:
English Fitting Instructions: Trophy and Trophy SE A9808015 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of proven engineering, exhaustive
More informationI. Introduction - basic information 3 II. Installation into a vehicle 3. III. Attachments 9
ampire FLEET200 Contents I. Introduction - basic information 3 II. Installation into a vehicle 3 1. Placement of the unit 3 2. Connecting the wiring harness 4 2.1 Input - IGNITION 6 2.2 Input BUSINESS
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More informationVoloMOD Full Feature Installation (Turn signals
VoloMOD Full Feature Installation (Turn signals output) In the Full Featured installation mode, VoloMOD flashes your turn signal lights at two different rates to provide an early indication of deceleration
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationKWIKEE DOOR SWITCH STEP ACTIVATION INSTALLATION GUIDE ( )
Purpose Note: Information for this document has been obtained from Kwikee Products document number 1421330, Revision 0B, dated February 2008 and updated for current practices. This document explains the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationCurrent Softail FLST Harley-Davidson. Ground Effects Installation Instructions
by 2000 - Current Softail FLST Harley-Davidson Ground Effects Installation Instructions Revised 1-2015 California Sidecar Parts & Technical Support 434.263.8866 Notice to installers 2007 and newer bikes
More informationLHT CC LIGHT WIRING Instructions for Club Car DS Models
LHT CC5 1001 LIGHT WIRING Instructions for Club Car DS Models This Light Kit includes: (1) Main Wire Harness with Dual InLine Fuses (1) Headlight Switch (1) Left hand headlight (1) Right hand headlight
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationTusk Pannier Racks. Instructions and information KLR
1 Tusk Pannier Racks Instructions and information KLR650 2008 + Congratulations on your purchase of the Tusk Pannier Racks. These racks are made to handle extreme adventure riding, but work great for the
More informationINSTALLATION MANUAL. Middle. Def tank. Standard. Middle. Standard. Def tank WARNING. Level of Difficulty CAUTION. Parts List.
INSTALLATION MANUAL 3025101 Level of Difficulty Moderate This is the second first of two of two manuals required to complete this installation. The first second manual manual is is included with with your
More informationPN DODGE CORONET Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationPN R CHEVY CAMARO w/reverse Two panel Sequential LED Taillight kit installation guide. Kit Contents:
Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2 LED extension
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationWater in Fuel Sensor Kit
03/08/2016 1050355-1050356 Water in Fuel Sensor Kit (I-00369) 1 Water in Fuel Sensor Kit Fast and Accurate Detection of Water in Diesel Fuel 1050355 Universal Kit For use with BD FlowMax water separator
More informationULX210. Register your product. Send us your photos. Warranty COLOR CHANGING LED UNDERCAR LIGHTING SYSTEM. Installation Manual
Register your product In order to provide you with prompt warranty service and technical support please register your product on line at www.varad.com/register. Be sure to have your product serial number
More informationFitting Instructions: Street Triple from VIN and Street Triple R from VIN A
English Fitting Instructions: Street Triple from VIN 560477 and Street Triple R from VIN 560477 A9808113 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of
More informationPN PONTIAC FIREBIRD. Kit Contents: Four Panel Sequential LED Tail Light Kit Installation Guide
1969 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100569 1969
More information1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide
1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED
More informationTail lights. Headlights
Revised December 2014 02-017 Light Kit will fit Yamaha G-Series* installation instructions included: tools needed: 2 Headlights 2 Tail Lights Wiring Harness Screws Straps Hazard Switch Phillips Head Screw
More information64-67 Chevelle. Power Rack & Pinion Cradle Kit
64-67 Chevelle Power Rack & Pinion Cradle Kit 64-67 Chevelle Note: For safety disconnect battery cables and ensure that the vehicle is properly supported by jack stands. Before painting or powder coating
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationPN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide
Four panel Sequential LED Taillight kit installation guide Kit Contents: 2 tail light LED panels 2 tail light turn signal LED panels 1 rubber boot/sleeve kit 1 power wire with t-tap 1 driver side LED harness,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Vehicle Alarm Impact Sensor 2. APPLICATION: G37 Sedan (2010) 3. PART NUMBER: 999M2 VU003 4. KIT CONTENTS: Item QTY Description A 1 Impact Sensor
More information3-5 Hours Professional installation recommended
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Toyota Tacoma Double Cab 2016 75162-01A Toyota Tacoma Access Cab* 2016 75162-01A * Modification required to running board assembly. See Item
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationFlaming River Ind. 800 Poertner Dr Berea, OH Chevy C-10 Rack and Pinion Conversion Kit
Flaming River Ind. 800 Poertner Dr Berea, OH 44017 800-648-8022 67-72 Chevy C-10 Rack and Pinion Conversion Kit For safety, disconnect battery cables and ensure that vehicle is properly supported by jack
More informationdually & d2 Ford raptor fog light bracket dually & d2 mounting instructions
dually & d2 Ford raptor dually & d2 fog light bracket mounting instructions Passenger Driver Thank you for purchasing Rigid Industries products for your Ford. Installation is fairly simple with the right
More informationAux. Battery and Isolator
Aux. Battery and Isolator ISOLATOR MOUNTING ALL YEAR VANAGONS Fig.1 1. Disconnect ground from main battery under passenger seat 2. Remove driver seat 3. Remove driver seat belt buckle from seat pedestal
More informationOLDSMOBILE CUTLASS
1971-72 OLDSMOBILE CUTLASS Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 Connector/Wire Kit 1 Grommet/Boot Kit 1 Power wire 2 Pigtail Harness Kits 1 Crimp terminal
More informationINSTALLATION AND WIRE CONNECTION MANUAL
INSTALLATION AND WIRE CONNECTION MANUAL 1. SAFETY PRES Symbol Identification This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to
More informationLine Lock Package, Mustang GT/GT500, 2007 PACKING LIST
PART #M25002 Line Lock Package, Mustang GT/GT500, 2007 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS 3.5 mm AUXILIARY CORD P/N 08A87-MKC-A00 GL1800/D/B/BD GL1800DA (go to page 7) Honda Dealer: Please give a copy of these instructions to your
More informationSide Rocker Installation Instructions
Side Rocker Installation Instructions Guidelines + Trial fit all parts prior to painting + Do not use the side rockers as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are
More informationw w w. h d o n l i n e s h o p. d e ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL INSTALLATION -J03554 REV.
-J03554 REV. 007-08-0 ROAD TECH QUEST GLOBAL POSITIONING SYSTEM (GPS) MOUNTING KIT GENERAL Kit Number 900-05 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories
More information58-62 Impala. Rack & Pinion Cradle Kit
58-62 Impala Rack & Pinion Cradle Kit 58-62 Impala Note: For safety disconnect battery cables and ensure that the vehicle is properly supported by jack stands. Before painting or powder coating of the
More informationModel-GS109 Brake Light Controller Module Installation & Users Guide
Thank you for purchasing the GS109 brake module. Please review this manual before starting installation. Quick Installation Guide: 1. Make sure the brake lights are working properly before module installation.
More informationINSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166
INSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166 PARTS INCLUDED 1 Lighted Curved Lay Down License Plate Assembly 1 Hardware Kit Including: 6 Cable Ties 1 Dielectric Grease Pack 1 1 x 8 Tape
More informationPONTIAC FIREBIRD. Four Panel Sequential LED Tail Light Kit Installation Guide
1967-68 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100567 Please
More informationPONTIAC FIREBIRD
1974-78 PONTIAC FIREBIRD Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 LED panel mount kits 6 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal
More informationThe Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationApplication Techniques for Reflective Pressure-Sensitive Films
Introduction Before starting application consult the appropriate product data bulletin for information regarding minimum and maximum application temperatures, recommended substrates, and immediate service
More informationEngine Management System
Engine Management System 6 0 4-0 0 1 I N S T R U C T I O N S For 2005-2010 Harley-Davidson FXS (Softail) Models 2 Revolution Performance was founded with two major goals in mind to go that extra mile providing
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More informationGL1800 TRAILER HITCH - INSTALLATION INSTRUCTIONS #GL
GL1800 TRAILER HITCH - INSTALLATION INSTRUCTIONS #GL18007-20 Read through these instructions completely before attempting installation, lay out all pieces including the numbered hardware bags to familiarize
More informationCHEVY CAMARO Four panel Sequential LED Taillight kit installation guide
1978-81 CHEVY CAMARO Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses, 48 4 LED
More informationMcDonalds Installation Guide
McDonalds Installation Guide Canopy COD Installation CCOD ------------------------------------------------------------------------------------------------------ Metal Pedestal COD Installation MCOD Everbrite
More informationPage 1. File: Motolight caliper one-piece Harley Date: 8/15/2006
Page 1 Harley-Davidson FL Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationNot Included. Rear Half Harness
Basic Light Kit 60102 Caution! Wear appropriate eye protection! Disconnect the battery or batteries. Place run/tow switch in tow position before disconnecting the batteries on models using that feature.
More informationPOWERED RUNNING BOARDS INSTALLATION MANUAL
POWE RUNNING BOARDS INSTALLATION MANUAL Level of Difficulty Moderate Parts List 1 Driver / left running board* 1 Passenger / right running board* 4 Mounting bracket, standard 2 Mounting bracket, middle
More informationRace Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE
Race Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE PARTS LIST (INCLUDED IN THE KIT) 1 x LED Control Center Box 2 x 48 RGB Aluminum Channel LED Bars 2 x 36 RGB Aluminum Channel LED Bars 1 x
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationLiteDOT Installation Document
LiteDOT Installation Document This document designed to aid in installation of LiteDOT s on Jeep TJ models, other models are similar. NOTE: Installing LiteDOT s on a Jeep where the 2 necessary mounting
More information1968 PLYMOUTH ROAD RUNNER
Sequential LED Tail Light Kit Installation Guide 1968 PLYMOUTH ROAD RUNNER PN 1200568 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed MOPAR product Note The LED boards
More informationPRXB EXHAUST BRAKE HIGH PERFORMANCE
HIGH PERFORMANCE PRXB EXHAUST BRAKE C44059, C4406, C44063, C44065 APPLICATION 994-2002 DODGE RAM AUTOMATIC TRUCKS EQUIPPED WITH 47RE TRANSMISSIONS WITH 5.9L, 24 VALVE CUMMINS DIESEL ENGINES GETTING STARTED
More informationApplicable to the Following Part Numbers. Notes and Maintenance. Torque Specifications. Metric SAE. Use above torque setting unless otherwise noted
INSTALLATION MANUAL Level of Difficulty Moderate This is the second first of two of two manuals required to complete this installation. The first second manual manual is is included with with your mounting
More informationInstallation of the AdMore Premium Light Bar on an Indian Motorcycle
Installation of the AdMore Premium Light Bar on an Indian Motorcycle May 16, 2017 by Ken the Mucker Sexton Ref: AdMore Lighting, LED8020-SB, Premium LED Light Bar with Smart Brake Technology, https://www.admorelighting.com/product/admore-smt-light-bar-with-smart-brake-technology-new/
More information750 Paso Wiring Upgrade
750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More informationULX210 COLOR CHANGING LED UNDERCAR LIGHTING SYSTEM
ULX210 COLOR CHANGING LED UNDERCAR LIGHTING SYSTEM Installation Manual Technical Specifications Colors: 1000 Patterns: 1 Strobe, 1 breathing Auto Color Change, 9 preset colors Auxiliary input for trigger
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More information- MK7 Mirror Integration Kit - Installation Instructions
- MK7 Mirror Integration Kit - Thank you for choosing the Double Apex Gentex Mirror Integration kit for your Volkswagen MK7. If you have any questions about the installation please email us at support@dblapex.com.
More informationTOYOTA LANCRUISER 79 SERIES (2007 to PRESENT) 110lt AUXILIARY TANK AUXILIARY FUEL TANK PARTS LIST AND FITTING INSTRUCTIONS PART NUMBER: TL79A2
Copyright This document contains technical information the property of TOYOTA LANCRUISER 79 SERIES (2007 to PRESENT) 110lt AUXILIARY TANK AUXILIARY FUEL TANK PARTS LIST AND FITTING INSTRUCTIONS PART NUMBER:
More informationBUICK SKYLARK/GS
Sequential LED Tail Light Kit Installation Guide 1970-72 BUICK SKYLARK/GS PN 1101170 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed GM product Note The LED boards are
More informationInstallation instructions for IPS parking Brake Kit for 1996 to 2002 Viper
Installation instructions for IPS parking Brake Kit for 1996 to 2002 Viper WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and Slimline Mirror (Kit part number 9002-8724) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the
More informationFord High Idle Kit PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
U 17 December 2014 2003-2004 Ford High idle Kit (I-00320) 1 Ford High Idle Kit 2003-2004 Ford 6.0L Diesel (Automatic transmission Only) 1036609 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD Engine
More informationRed Mountain Products 2014 Honda Pioneer Switch Panel Kit with Harness
Red Mountain Products 2014 Honda Pioneer Switch Panel Kit with Harness WARNING INSTALLING THIS KIT REQUIRES THE REMOVAL OF A SAFETY WARNING PLACARD PLACED ON THE PIONEER AT THE BEHEST OF HONDA MOTOR COMPANY
More informationPart Number: Code: CL7
Document # 16.01.00 PIO/DIO Rev. A 06/23/08 TOYOTA YARIS 2008- ELECTRONIC CRUISE CONTROL KIT Part Number: 00016-52030 Code: CL7 Section I Installation Preparation Kit Contents Item # Qty. Description 1.
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationFour Panel Sequential LED Tail Light Kit Installation Guide
1969 CHEVY CAMARO Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses,
More informationSUPPLEMENTAL WARNING LIGHT KIT
3656 Paragon Drive Colum, Ohio 43228 Phone: (800) 989-2718 Fax: (614) 527-3547 www.weldoninc.com SUPPLEMENTAL WARNING LIGHT KIT Installation Instructions IMPORTANT! Read this document completely before
More informationWARNING WARNING WARNING. English Quick start guide CAUTION CAUTION. Installation Precautions
English Quick start guide Symbol Identification This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to carefully read and understand
More informationINSTALLATION INSTRUCTIONS
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8723) Items Included in the Kit: Bubble bag containing: Camera with Mount Mirror Mirror
More information