Model-GS109 Brake Light Controller Module Installation & Users Guide
|
|
- Rose Park
- 6 years ago
- Views:
Transcription
1 Thank you for purchasing the GS109 brake module. Please review this manual before starting installation. Quick Installation Guide: 1. Make sure the brake lights are working properly before module installation. 2. Remove the seat and the body center cover to gain access to the brake light wiring harness. 3. With the ignition switch carefully cut about a 2.5 inch section of the harness cover to expose the brake light wires. 4. Attach the Black wire from the control module to one of the green ground wires using the included tap splice connector. 5. Cut the Green/Yellow brake signal wire and strip both ends back about 3/8 of an inch. 6. Use the included Lever-Nut to connect the RED wire from the control module to the Green/Yellow brake signal wire coming from the brake switch. Lift up orange lever and insert stripped end of wire. Snap orange lever down keeping fingers from underneath lever. 7. Use the included Lever-Nut to connect the WHITE wire from the control module to the remaining Green/Yellow wire that s going directly to the brake lamp. Lift up orange lever and insert stripped end of wire. Snap orange lever down keeping fingers from underneath lever. 8. Verify operation by turning the ignition switch and applying the brakes while monitoring the brake light. The brake light should flash several times (depending on dip switch settings) ending with a solid on condition until brakes are released. The onboard LED output indicator will follow this same sequence. 9. Adjust dip switches for the desired operation. Install dip switch cover. Place a wire tie though the hole on the tie mount that is on the back of the brake module and attach to the frame. Place a second wire tie around the module and frame to help secure the module. Make sure module does not interfere with seat. Keep module from rubbing against metal as this may cause damage to the module over time. 10. Install center cover and seat. Brake Light Module Schematic Brake Switch +12V BLACK RED Green/Yellow Brake Signal Wire +12V When Brakes are Applied WHITE Cut Wire Battery Brake Lamp Green Ground Wire Page 1 of 10
2 Detailed installation guide: 1. Make sure the brake lights are working properly before module installation. 2. Remove the seat and the body center cover to gain access to the brake light wiring harness. Page 2 of 10
3 Wiring Harness on Left Side of Bike. Page 3 of 10
4 3. With the ignition switch carefully cut about a 2.5 inch section of the harness cover to expose the brake light the wires. Page 4 of 10
5 4. Attach the Black wire from the control module to one of the green ground wires using the included tap splice connector. 5. Cut the Green/Yellow brake signal wire and strip both ends back about 3/8 of an inch. Page 5 of 10
6 6. Use the included Lever-Nut to connect the RED wire from the control module to the Green/Yellow brake signal wire coming from the brake switch. Lift up orange lever and insert stripped end of wire. Snap orange lever down keeping fingers from underneath lever. 7. Use the included Lever-Nut to connect the WHITE wire from the control module to the remaining Green/Yellow wire that s going directly to the brake lamp. Lift up orange lever and insert stripped end of wire. Snap orange lever down keeping fingers from underneath lever. Page 6 of 10
7 8. Verify operation by turning the ignition switch and applying the brakes while monitoring the brake light. The brake light should flash several times (depending on dip switch settings) ending with a solid condition until brakes are released. The onboard LED output indicator will follow this same sequence. 9. Adjust dip switches for the desired operation. Install dip switch cover. Place a wire tie though the hole on the tie mount that is on the back of the brake module and attach to the frame. Place a second wire tie around the module and frame to help secure the module. Make sure module does not interfere with seat. Keep module from rubbing against metal as this may cause damage to the module over time. 10. Install center cover and seat. Page 7 of 10
8 View from right side of bike. Page 8 of 10
9 Operation Once installed and brakes are applied the controller will flash the brake light/s multiple times and then it will hold the light/s on until the brakes are released. This flash and hold pattern (See Dip Switch Settings) will repeat every time the brakes are applied. 2 Stage Stop-n-Go Mode When enabled the Stop-n-Go mode will eliminate or reduce the number of flashes when the brakes are used in heavy traffic. Brakes are first applied = Normal flash and hold pattern. Stage -1 Brakes are released and applied again within 5 seconds = Light/s will go out when brakes are released and come on solid (no flash) when brakes are reapplied. Stage-2. Brakes are released and applied again between 5 and 15 seconds = Light/s will flash once and then hold until brakes are released. Brakes are released and then applied after 15 seconds = Normal flash and hold until brakes are released. Troubleshooting Symptom Brakes are applied - No onboard LED and no brake light operation. Brakes are applied Onboard LED flashes but no brake light. Solution Verify module red wire has 12vdc when brakes are applied. Verify module black wire is connected to bulb ground wire. Verify module white wire is connected to the brake light bulb. Check light bulb. Page 9 of 10
10 Dip Switch Settings These are rocker style dip switches. Remove switch cover and use something with a small tip like a paper clip or a sharp pencil to set switches. Replace cover. Flash Cycles (number of flashes) Switch 1 Switch 2 Flash Rate (Speed) Switch 3 Flash Rate 2 per second 4 per second Stop-N-Go mode Switch 4 Stop-N-Go mode Page 10 of 10 Flash Cycles
V-Bullet Installation Instructions
V-Bullet Installation Instructions Thank you for purchasing our high quality V-Bullet disc LED kit. Your business is greatly appreciated. Please follow the instructions below. Failure to follow the procedure
More informationATTENTION. Custom Dynamics Smart Triple Play Installation Instructions. Package Contents: - Smart Triple Play Module (1) - Instructions
Custom Dynamics Smart Triple Play Installation Instructions We thank you for purchasing the Custom Dynamics Smart Triple Play. Our products utilize the latest technology and high quality components to
More informationOwner s Manual Electronic Harness Controller P/N ASM4250
Owner s Manual Electronic Harness Controller P/N ASM4250 Thunder Heart Performance Corporation MANUAL P/N EI4250 120 Industrial Drive Revision 6/3/04 White House, TN 37188 www.thunder-heart.com TABLE
More informationTable of Contents. Bikes with 2 handlebar switches. 12-pin plug for BMW models Installation tips. 15-pin plug for older BMW models Installation tips
Table of Contents Bikes with 2 handlebar switches SM-5 12-pin plug for BMW models Installation tips 2 3 SM-6 15-pin plug for older BMW models Installation tips Special Features & Functions 4 5 4-Way Emergency
More informationTOYOTA COROLLA 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationELS Electronic Lighting System
ELS Electronic Lighting System T-8 Lamp Replacement November, 2012 99-20374-I001 I. T-8 Lamp Replacement Instructions Center Mullion Fixtures 1. Turn light power off before start of lamp replacement. 2.
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationTotal installation time for the cruise control was approximately 8 hours.
The following summary highlights the start-to-finish install of an Audiovox cruise control on stellarpod s (Steve) ST1300. Fred D (Fred) and ChucksKLRST (Chuck) primarily performed the install (Steve did
More informationTOYOTA YARIS KEYLESS ENTRY SYSTEM
TOYOTA YARIS 2011 - KEYLESS ENTRY SYSTEM Part Number: 00016-32901 Accessory Code: KE1 Conflicts Not for installation in vehicles equipped with factory installed keyless entry. Kit Contents Item # Quantity
More informationSivoia QS Wireless Drapery Lite System
Sivoia QS Wireless Drapery Lite System English Installation Guide Please Read Before Installing Important Notes - Please Read Before Installing A. Lutron systems are intended for use with only Lutron hardware
More informationV-HID Headlight Installation Instructions
V-HID Headlight Installation Instructions Thank you for purchasing our New high quality easy to install Parts4PowerToys V-HID headlight kit for your Harley Davidson. The following installation instructions
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1992 Infiniti G20 1990-92 BRAKES Infiniti Anti-Lock Brake System Infiniti; G20, M30, Q45 DESCRIPTION & OPERATION The Anti-Lock Brake System (ABS) prevents wheel lock-up during abrupt
More informationGENERAL SAFETY PRECAUTIONS
GENERAL SAFETY PRECAUTIONS WARNING! MOVING PART HAZARDS To prevent serious injury and property damage: Do not operate or install this product without reading and understanding these instructions. Keeps
More informationTOYOTA COROLLA 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles
More informationInstalling LED courtesy lights in Mustang.
Installing LED courtesy lights in 2005 2010 Mustang. This procedure is to provide you with the basics for installing LED strips under the dash and changing the map or courtesy lights to LED. Use the Ford
More informationInstallation Instructions for Foam Marker ZMAX
2017 Installation Instructions for Foam Marker ZMAX We appreciate your purchase of L.T. Rich s Product. Please Verify Contents before beginning installation. JLD;AES L.T.RICH 5/2/2017 SHIPPING CONTENTS...
More informationTOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-350-AIT ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-250-M2 ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate Maxima (Applicable ONLY to U.S. Market Vehicles with Build Date June 2012 or later) 999G6
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: ILLUMINATED KICK PLATE APPLICATION: QUEST(2010) PART NUMBER: ILLUMINATED KICK PLATE (G6950-1JA0A(BEIGE)/G6950-1JA0B(GRAY)) KIT CONTENTS: Item QTY Part
More informationSTREET SCENE EQUIPMENT,INC. CONNECTING STREET SCENE SIGNAL MIRRORS
STREET SCENE EQUIPMENT,INC. CONNECTING 365 McCormick Avenue STREET SCENE SIGNAL MIRRORS Phone (714) 426-0590 Fax (714) 426-0591 1993-2001 CONNECTING STREET SCENE SIGNAL MIRRORS INSTRUCTIONS FOR PART NUMBERS
More informationLED Fog Light. Conflicts Note: 1226, General Applicability Fits Models Additional Items Required For Installation
LED Fog Light Year & Model Part Number Conflicts Note: 1226, 1228 2017 Prius TPR-817 General Applicability Fits Models 1221 1225 1223 1227 1224 Additional Items Required For Installation Items 1 N/A 2
More informationCustom Dynamics LED Tri-Bar Fender Tip Installation Instructions
Custom Dynamics LED Tri-Bar Fender Tip Installation Instructions We thank you for purchasing the Custom Dynamics LED Tri-Bar Fender Tip! Our products utilize the latest technology and high quality components
More informationInstallation Instructions: External-Driver SEP T8 LED Tube Lamp
Installation Instructions: External-Driver SEP T8 LED Tube Lamp Installation Notes & Precautions: External-Driver SEP T8 LED Tube Lamp Read all precautions, warnings, instructions contained in this document.
More informationHEADLIGHT AND TAILLIGHT
BE14 HEADLIGHT AND TAILLIGHT SYSTEM PARTS LOCATION BE15 TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction are
More informationNetworkfleet 3500 Product Line Installation Guide
Networkfleet 3500 Product Line Installation Guide Light/Medium Duty (L3500) Heavy Duty (H3500) Universal (U3500) www.networkcar.com/fleet Customer Care: (866) 227-7323 customercare@networkcar.com Table
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
May 1, 2018 Lit. No. 29206, Rev. 13 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 7 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/3 PLUG SYSTEM HARNESSES Installation Instructions Read this
More informationInstallation instructions, accessories. Body kit
Installation instructions, accessories Instruction No 31265373 Version 1.1 5 Part. No. Body kit IMG-256263 Volvo Car Corporation Body kit - 31265373 - V1.1 Page 1 / 42 Equipment A0000162 A0000163 IMG-239664
More informationSCION tc SECURITY (V5) Preparation
Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29206, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/3 PLUG SYSTEM HARNESSES Installation Instructions Read
More informationTOYOTA TACOMA TVIP V5
Preparation Part Number: PT398-35090 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor/Microphone 5 2 Warning Labels (English) 6 2 Warning
More informationAccessory Harness & Bracket Kit
Accessory Harness & Bracket Kit Stainless Steel Hopper Spreader Gas 9969 June 5, 06 Lit. No. 98986, Rev. 0 PARTS LIST 9 4 8 7 6 4 3 8 VIB LIGHT STROBE PREWET 5 0 4 9969 Accessory Harness & Bracket Kit
More informationRANGER 900 POWER STEERING KIT
RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this
More informationOnboard. Onboard RTU270 Installation Manual
Onboard Onboard RTU270 Installation Manual Contents Parts Checklist 3 Pre-installation considerations 4 Installation 5 Status LEDs 7 Completing Installation 8 2 Onboard RTU270 Installation Parts Check
More informationSERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL
SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location
More informationModel FHL-CHG Headlight Flasher (Isolation Model) for Positive-Side Switched Headlights
Model FHL-CHG Headlight Flasher (Isolation Model) for Positive-Side Switched Headlights 2562581A REV. A 910 Safety Message to Installers of Federal Signal Products People s lives depend on your proper
More informationSteering Column - Steering Column Removal and Installation
Page 1 of 7 Steering Column - Steering Column Removal and Installation Removal WARNING: Take care if releasing the adjustment lever when the column has been removed from the vehicle. The spring is under
More informationOptimized Idle Aftermarket Installation Kits On-Highway Truck Applications (P/N: )
18SP655 Optimized Idle Aftermarket Installation Kits On-Highway Truck Applications (P/N: 23538534) KIT DESCRIPTION The Optimized Idle Aftermarket Installation Kit provides the components necessary for
More informationSignal Mirror Installation Instructions Standard West Coast Mirror
Signal Mirror Installation Instructions Standard West Coast Mirror THE safety accessory of the 21 st Century. P/N 210-0058-0 Rev A1 (6-29-04), GG 2002 Muth Mirror Systems, LLC. Note: Professional Installation
More information2004/2013 Harley Davidson Road Glide
2004/2013 Harley Davidson Road Glide VORTEX XMC-575OD SERIES SPECIFICATIONS 1. Warranty : Extended 2. Input Voltage : 12V 3. Modes : Low, High, Halo 4. LED Lifespan : 50,000 Hours WARNING: Due to excessive
More informationVoloMOD Full Feature Installation (Turn signals
VoloMOD Full Feature Installation (Turn signals output) In the Full Featured installation mode, VoloMOD flashes your turn signal lights at two different rates to provide an early indication of deceleration
More informationSolstice Electric Fryers SE Series Service Manual
Solstice Electric Fryers SE Series Service Manual L22-330 R1 (10/12) Notice In the event of problems or questions about your order, contact the Pitco Frialator factory at (603) 225-6684. In the event of
More informationInstallation Instructions for Key Switch SNOWRATOR
2017 Installation Instructions for Key Switch SNOWRATOR We appreciate your purchase of L.T. Rich s Product. Please read carefully before Operating or detaching. AES L.T.RICH 6/15/2017 SHIPPING CONTENTS...
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationSTANDARD AND GROUND SWITCHED APPLICATIONS
SNOWDOGG LIGHT REFERENCE STANDARD AND GROUND SWITCHED APPLICATIONS GENERAL REFERENCE SNOWDOGG LIGHT REFERENCE GENERAL REFERENCE 3 TROUBLESHOOTING GUIDES/PROCEDURES 6 CONNECTOR REFERENCE 12 ADAPTER HARNESS
More informationTOYOTA AVALON EC REARVIEW MIRROR
Section I - Installation Preparation Part Number: PT732-07000 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Full Mirror Assembly, Compass 2 1 Hardware Bag 3 1
More informationInstallation Instructions Harley-Davidson Saddlebag Lids
Installation Instructions Harley-Davidson Saddlebag Lids Thank you for your purchase of Bagger Audio Saddlebag Lids for your Harley- Davidson motorcycle. We have carefully engineered these products to
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Illuminated Kick Plate APPLICATION: INFINITI M45 (2010) PART NUMBER: G6950-1MA0B KIT CONTENTS: Item QTY Description SERVICE PART NUMBER
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford F-250 to F-750 Pick-Up, Super-Duty 1998-2007 Trailer Tow Mirror Ford Excursion XLT/Limited 2000-2002 Trailer Tow Mirror Ford Excursion (all models) 2003-2005
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationDynojet Research 2191 Mendenhall Drive North Las Vegas, NV (800)
007 Ducati 098 I n s ta l l a t i o n I n s t r u c t i o n s Parts List Power Commander CD-ROM Button Adjustment Display USB Cable Installation Guide Power Adapter Wire Tap Power Commander Decals Dynojet
More informationVehicle Rear Observation System With Integrated Parking Sensors
Vehicle Rear Observation System With Integrated Parking Sensors Model: CAMSBAR Installation/User Manual Features: 2.5" LCD Color Display 2 Ultra Sonic Rear Obstacle Sensors On-screen Display Function Automatically
More informationLakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationTOYOTA RAV TRAILER WIRE HARNESS Preparation
Preparation Part Number: PU322-42013-UW Kit Contents Item # Qty Description 1 1 Trailer Module Harness 2 1 Trailer 4-Flat Harness 3 1 Trailer Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24
More informationULX210 COLOR CHANGING LED UNDERCAR LIGHTING SYSTEM
ULX210 COLOR CHANGING LED UNDERCAR LIGHTING SYSTEM Installation Manual Technical Specifications Colors: 1000 Patterns: 1 Strobe, 1 breathing Auto Color Change, 9 preset colors Auxiliary input for trigger
More informationConf licts Note: TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: Accessory Code: LL1000.
TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: 00016-00069 Accessory Code: LL1000 Conf licts Note: Color Applicability/Trim Level Kit Contents Item # Quantity R eqd. Description
More information5 Removal and replacement
5 Removal and replacement This chapter describes the removal and replacement of field-replaceable units (FRUs) only. Removal and replacement strategy User-replaceable parts Covers Internal assemblies ENWW
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL and STAR SABRE ECE Compliant Plus Lightbars PLIT429ECE REV. C 3/31/14 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring,
More informationINSTALLATION OVERVIEW:
INSTALLATION OVERVIEW: signalminder is a 100% solid-state device, which replaces the existing turn signal relay of your bike - in many cases this a simple plug-in procedure. But depending on your bike,
More informationCMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION
CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This,
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29225, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/2 PLUG SYSTEM HARNESSES Installation Instructions Read
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29206, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/3 PLUG SYSTEM HARNESSES Installation Instructions Read
More informationRS4/RS7 + ADS-DL (GM2)
Installation tips for RS4/RS7 + ADS-DL (GM2) Tip Sheet T2390, T3632 (Chevy Cobalt 2007-2010), (Chevy HHR 2007-2011), (Chevy Malibu 2007-2012), (Chevy Malibu Hybrid 2008-2012), (Chevy Malibu Maxx 2007-2009),
More informationBody Electrical System
Body Electrical System GENERAL....BE -2 MULTI FUNCTION SWITCH...BE -8 HORN...BE -11 FUSES AND RELAYS...BE -12 INDICATORS AND GAUGES...BE -19 LIGHTING SYSTEM...BE -24 DAYTIME RUNNING LIGHTS...BE -30 BE-2
More informationConfiguration and Programming 1
Configuration and Programming 1 GENERAL PROCEDURES Superseded by:sgml_id= n1132613 7. From the technician service publication site Effect:Frozen: N 2009 MIKETEST 19 020 (PTS), run OASIS using Quick Start.
More informationw w w. h d o n l i n e s h o p. d e HEATED HAND GRIP KITS GENERAL REMOVAL -J02983 REV Kit Number Models Kit numbers Service Parts
-J098 REV. 007-0-0 GENERAL Kit Number 56047-0B, 5607-0B, 5674-0B, 5696-0B, 565-0B, 5669-0A, 56694-04A, 56750-04A, 5688-0A, 569-05, 5696-05, 56997-07 Models For model fitment information, please see the
More informationCustom Dynamics Spyder Stingerz Installation Instructions
Custom Dynamics Spyder Stingerz Installation Instructions We thank you for purchasing the Custom Dynamics Stingerz! Our products utilize the latest technology and high quality components to ensure you
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More information* * APPLICABLE MODELS: 2014 > Mazda 6
PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Chevy Blazer 1992-1994, Chevy Suburban 1992-1999, Chevy Tahoe 1995-1999, Chevy Tahoe Limited 2000, GMC Suburban 1992-1999, GMC Yukon 1992-1999, GMC Yukon Denali
More informationTOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of
More informationONBOARD AIR SYSTEM FOR ALL VEHICLES APPLICATIONS
ONBOARD SYSTEM FOR ALL VEHICLES APPLICATIONS Thank you and congratulations on the purchase of a Pacbrake onboard air system. Please read the manual prior to starting to ensure you can complete the installation
More informationDESCRIPTION & OPERATION
SEATS - POWER 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Power Seats DESCRIPTION & OPERATION Power seats operate using toggle switches located on seat side. Seat adjusters are powered by a 12-volt,
More informationAnthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A
Anthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A 99-16999-0000 Table of Contents 1. Removing Fluorescent Lighting... 4 1.1. Detach the lens assembly... 4 1.2. Remove
More informationSPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
More informationProcedure. These guidelines can be found in the "Accessory Installation Practices" document.
Toyota Tundra 207 LED Illumination Package Part Number: 0006-00069 (Interior and Exterior) Accessory Code: LL000 Conf licts V ehicles with Option Code BZ Color Applicability/Trim Level Kit Content 4 Puddle
More informationCustom Dynamics LED Plugz Installation Instructions
Custom Dynamics LED Plugz Installation Instructions We thank you for purchasing the Custom Dynamics LED Plugz! Our products utilize the latest technology and high quality components to ensure you the brightest,
More informationTOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT
Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents
More information29048, 29049, 29050, 29051, 29052, 20953, 29054,
July 15, 2008 Lit. No. 29225, Rev. 06 29048, 29049, 29050, 29051, 29052, 20953, 29054, 29400-2 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM w/2-plug SYSTEM HARNESSES Installation Instructions Read
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationRIGHT HYDRAULIC PUMP. Right Hydraulic Pump Replacement. Right Hydraulic Pump Removal. 5. Remove the pump belt from around the pump pulleys (Fig. 002).
Right Hydraulic Pump Replacement Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all exposed surfaces prior to any type of maintenance. Cleaning all parts
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford F-250/F-350 Pick-Up, Super-Duty 1998-2006 Ford Excursion XLT/Limited 2000-2002 Ford Excursion (all models) 2003-2006 THE safety accessory of the 21st Century.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationField Replacement of Fluorescent Power Supply in L-858 Signature Series Sign
Field Replacement of Fluorescent Power Supply in L-858 Signature Series Sign Document No. Issued: December 13, 2006 Rev. C: March 25, 2008 ADB Airfield Solutions Copyright 2009 by ADB Airfield Solutions.
More informationCustom Dynamics LED Plugz Installation Instructions
Custom Dynamics LED Plugz Installation Instructions We thank you for purchasing the Custom Dynamics LED Plugz! Our products utilize the latest technology and high quality components to ensure you the brightest,
More informationJ2 Remove sound insulation/knee guard 1 and side panel 2 on center console
J1 Preparations Drive car forward on a level surface so that wheels are straight. Disconnect battery negative lead. Turn ignition key to position 1 so that steering lock is off. J2 Remove sound insulation/knee
More informationInstallation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( FIT), ( Pilot), ( Ridgeline) Acura: ( MDX)
Installation Tips for your RS-1 + Honda-SL3 (1.b) Remote starter Honda: ( 06-08 FIT), ( 05-08 Pilot), ( 06-13 Ridgeline) Acura: ( 03-06 MDX) TIP SHEET T0777 Thank you for purchasing your remote start from
More informationTOYOTA PRIUS 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-47091 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationTOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation
Preparation Part Number: 08586-48070 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 ECU Mounting Bracket Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Microphone
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More information