Rotary Paddle Level Switch
|
|
- Jonathan Evans
- 5 years ago
- Views:
Transcription
1 Rotary Paddle Level Switch
2 INTRODUCTION PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material present) a synchronous motor rotates the paddle at RPM. hen this paddle rotation is impeded by material, surrounding the paddle, motor will stall and cause the Micro-switch to change state. (indicating an alarm or control) APPLICATIONS Suitable for powdery producing & processing industries such as plastic, chemical, medical, forage, cement and fertilizer powders. FEATURES Airtight sealing device, outdoor application is available. Unique sealing ring design, it can perform good dust protection to avoid the dust permeate into housing body along with the shaft. The torque force is adjustable. The performance of torsion is stable and reliable. If the rotary paddle bears an extra overload, the motor will be appeared slide to prevent the inside mechanism damaged. It is rationally designed, the inside mechanisms are easily tore down for checking, maintenance and replacement. It doesn't necessary to remove the complete set from the tank. Very suitable for small tank and material of low density STRUCTURE SAFT FLANGE CLUTC MOTOR PADDLE BODY OIL-SEAL NUT BEARING MICRO SITC STANDARD TYPE Paddle Shaft Clutch assembly Body Case TORQUE SPRING Bearing Nut Oil seal Cable Motor Micro Switch MINI TYPE
3 ORKING PRINCIPLE & TORQUE ADJUSTING CONTROL SITC DEVICES ORKING PRINCIPLE.hen the synchronous motor is turning. It means that material isn't touching the paddles, the (C.L) stands for "terminal point connected"..hen material is touching the paddles, (C.L) stands for "cut-off", (C.) stands for "connected" the synchronous motor's current is to be cut off. 3.hen the material drops away from the paddles, the synchronous motor runs again and the terminal point is connected, (C.L) show that the cycle has begun again. ITE BLACK BLUE YELLO RED M L C Limit S. NO. Limit S. NO. TORQUE ADJUSTING MECANISM The torque spring is applied to adjust the shaft output torque force, which is set at "weak" position at factory side, it is adjustable as per customer side target measuring material S.G. (special gravity), if the measured material with higher S.G., please try to release it to more stronger spring force position step until you found the proper orientation. The paddle sensitivity will be interacted by more weaker, otherwise, the low S.G. material will release torque spring to the weakest position, which will cause the paddle performance to be more sensitive. Do not tamper with the spring as it may cause the Rotary Paddle to be malfunction. Resetting torque adjusting spring strongest strong weak weakest spring adjusting hole weakest weak strong strongest Terminal strip 0Vac or 0Vac NC NO COM Available: SE0, 0,, 40, 60, 70 white blue red black yellow green Resetting torque adjusting spring 0 ~ 55 Vdc strongest strong weak weakest 4Vac or 0Vac or 0Vac or 40Vac NC COM NO Available: SE80 V+ V- NO COM NC SEA-0D-B PA CC 0~55 NO NC Vdc COM GND Available:SE0E
4 STANDARD SPECIFICATION Power source : ( A) 0Vac,( B) 0Vac,( C) 40Vac, (D)4Vac, 50/60z (E)4Vdc Power consumption : 3, (DC4V) Contact capacity : SPDT, 5A/50Vac Rotary speed : R.P.M. Insulation test voltage : 500V Torque : 0.5 ~.0 kg-cm Connect : "PF screw or JIS -/"5kg/cm flange Protection/ material : IP65 / ADC- Conduit : /"PF Specific gravity : 0.5 SE0A/B/C/D/E SCRE TYPE orizontal mounting Operation Temp. (-0BC ~ 70BC) eight:. kg SE0A/B/C/D/E SEA/B/C/D/E Order No. SEA/B/C/D/E FLANGE TYPE orizontal mounting Operation Temp. (-0BC ~ 70BC) eight:.7 kg SE0A/B/C/D/E SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Operation Temp. (-0BC ~ 70BC) eight:. kg The whole section from flange to paddle are made of SUS 4 L--50mm (. kg) L--500mm (.5 kg) L--750mm (.8 kg) "PF 0 /"PF 40 SE0A/B/C/D/E /"PF 63 PCD SEA/B/C/D/E /"PF /"PF 35 SEA/B/C/D/E SAFT LENGT ADJUSTABLE TYPE Vertical mounting Operation Temp.. (-0BC ~ 70BC) L ~6mm (.5 kg) L ~0mm (.8 kg) L ~00mm (3.0 kg) 4 PCD f7. L 80 PCD f9 f.7 f8 4 L 65 3
5 STANDARD SPECIFICATION Power source : ( A) 0Vac,( B) 0Vac,( C) 40Vac, (D)4Vac,50/60z (E)4Vdc Power consumption : 3, (DC4V) Contact capacity : SPDT, 5A/50Vac Rotary speed : R.P.M. Insulation test voltage : 500V Torque : 0.5 ~.0 kg-cm Connect : "PF screw or JIS -/"5kg/cm flange Protection/ material : IP65 / ADC- Conduit : /"PF Specific gravity : 0.5 SE40A/B/C/D/E I-TEMP TYPE orizontal mounting Temp. (-0BC ~ 00BC) eight:. kg SE40A/B/C/D/E SE4A/B/C/D/E SE4A/B/C/D/E I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Operation Temp. (-0BC ~ 00BC) The whole section from flange to paddle are made of SUS 4 L--50mm (.6 kg) L--500mm (.9 kg) L--750mm (3. kg) PCD /"PF PCD f7. 80 /"PF 4 9 L 65 SE46A/B/C/D/E I-TEMP SAFT LENGT ADJUSTABLE TYPE Vertical mounting Operation Temp. (-0BC ~ 00BC) L ~6mm (3 kg) L ~0mm (3.3 kg) L ~00mm (3.5 kg) SE46A/B/C/D/E /"PF 9 SE60A/B/C/D/E /"PF 35 PCD 4 SE60A/B/C/D/E CABLE IRE TYPE Vertical mounting Operation Temp. (-0BC ~ 70BC) L-- 450mm (.5 kg) L-- 650mm (.8 kg) L-- 750mm (3 kg) PCD f9 f.7 f8 4 L f8 L (max.4m) 4
6 STANDARD SPECIFICATION Power source : ( A)0Vac,(B)0Vac,(C)40Vac, (D)4Vac, 50/60z Power consumption :.5 Contact capacity : 3A/50Vac Rotary speed : R.P.M. Protection/ material : IP65 / PC Temp. : -0LC ~ 70LC Cable length : cm (available for custom length) Torque : ~ g-cm Specific gravity : 0.3 SE80A/B/C/D CROSS-LIKE 4 BLADE PADDLE orizontal mounting Operation Temp. (-0BC ~ 70BC) eight : 0.4 kg SE809CRI RECTANGLE SUS4 PADDLE orizontal mounting Operation Temp. (-0BC ~ 70BC) eight : 0.48 kg SE80A/B/C/D /4"PF 7 0.5mm x6c cable Standard length 0mm SE809CR SUS4 SE809CRI /4"PF 5 0.5mm x6c cable Standard length 0mm SE809CR SCIMITAR TYPE PADDLE orizontal mounting Operation Temp. (-0BC ~ 70BC) eight : 0.4 kg 3/4"PF 0.5mm x6c cable Standard length 0mm 5 SE89CRI Shaft Protective Type SE89CRI SAFT PROTECTIVE TYPE orizontal /Vertical mounting Operation Temp. (-0BC ~ 70BC) eight : 0.4 kg L=50~400 f.7 3/4"PF 5 0.5mm x6c cable Standard length 0mm SE849CR SE849CRI I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Operation Temp. (-0BC ~ 00BC) eight : 0.4 kg L=50~ f.7 3/4"PF 8 5 f88 0.5mm x6c cable Standard length 0mm 5
7 EXAMPLES OF MOUNTING EXAMPLES OF MOUNTING TO TANK here the SE0A type paddle cannot be attached to the main shaft from inside the storage tank. The paddle can be set on the main shaft when the distance from the flange face to the tip of paddle is more than 90mm, the relative dimensions being as illustrated right. The scimitar paddle penetrate through 3/4"PF inlet directly like illustrated drawing, then screw tightly. Min Min.3/4"PF Max.45 Max.5mm INSTALLATION EXAMPLE FOR INJECTION MOLDING MACINE Steps to Install the Injection Molding Machine Injection Molding Machine usually use Se80 Install the Rotary Paddle through a Dia. f0mm ole on the Silo Remove the paddle from the device by taking out the fastening pin Insert the SE80 through the mounting hole and tighten it After which, secure the Paddle to the SE80 by locking it to the shaft with the the pin Keep in mind to 'widen' the opening of the pin in order to secure it 6
8 EXAMPLE SE4 SE SE0 5B SE0 SE INSTALLATION NOTICES. Please side mount the sensor by inclined 5 B~0 B to decrease the material inflowing impact.. For igh Temperature application whereby the temperature inside the tank is more than 70BC Please use SE49 Series. 3. SE0~SE40 on " connection pipe inlet, please apply scimitar type to screw directly. 4. SE, SE46 family items are with flexible and extensible shaft. 5. Please ensure that the Cable Gland point downwards and the nut must be fastened to secure the device. 7
9 ORDER INFORMATION ( ) MODEL NO. 9 : Standard type 0 : Shaft protective tube type : Shaft length adjustable type 49 : i-temp type 60 : Cable wire type 89 : Mini type VOLTAGE A : 0Vac B : 0Vac C : 40Vac D : 4Vac E 4Vdc(SE9/0//49/60) 50/60z MOUNTING Size for flange or screw C: 3/4" D: " E: -/" F: " G: -/" : 3" I : 4" J : 5" K: 6" S : Others 3 : -/4" SE0~SE60 series: The size of connecting screw is ". Pressure range or other M: 5kg/cm N: 0kg/cm O: 50 Lbs P : 0 Lbs Q: PT R: PF (G) T : BSP U: NPT S : Others PADDLE SAPES SE0~SE70 A : () B : 6580 () C : 650 () D : 8080 () E : 50 () F : Scimitar J : 008 () S : others - : None SE80 (Mini paddle type) G : Cross type paddle : Scimitar type paddle I : x (x) LENGT (mm) 0500: below 500mm 0: 50~0mm 500: ~500mm 80 A G 98 B,C,D 0 Material:PC Material:PP Material:SUS SE0~70 L: The distance from flange to paddle. SE80 L: Length of cable. The total length of item will be allowed a tolerance to A6mm. 500mm per Unit Use English letter as first code for probe length over 0m. A50 represents 5m, A00 represents 0m Order Notice. Please make sure the Voltage 4Vac, 0Vac, 0Vac or 40Vac, 50/60 z.. Please make sure the side or top mounting. 3. Please make sure the material specific gravity (S.G.) value. 4. Please make sure whether any bridge block or vibrating motor installed onto the tank wall. Please try to apply our item SA40 capacitance level sensor. 5. Please make sure the rotary paddle size is available to enter into the flange inlet. E I F 3 J 00 Material:SUS 8 8
10 ENCLOSURE Power source : (A)0Vac, (B)0Vac, (C)40Vac, 50/60z Power consumption : 3 Contact capacity : SPDT, 3A/50Vac Rotary speed : R.P.M. Insulation test voltage : AC 500Vminute Torque : 0.5 ~.0 kg-cm NEPSI PROOF No.GYJ0637 Ex d IIC T3~T6 PTB PROOF No. 05 ATEX 09 II G EEx d IIB T3~T6 II D IP65 T3~T6 Connect : "PF screw or flange "~6" -/"5kg/cm (std.) Enclosure material : AL Alloy, ADC- Enclosure Protection : Ex d IIC T4~T6 Conduit : /" (std.) or 3/4"NPT Specific gravity : 0.5 SE70A/B/C/D SCRE TYPE orizontal mounting Temp. (-0BC ~ 70BC) 90 "PF f SE7A/B/C/D SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Temp. (-0BC ~ 70BC) L-- 50mm L-- 500mm L-- 750mm 0 f3 08 "PF SE7A/B/C/D FLANGE TYPE orizontal mounting Temp. (-0BC ~ 70BC) f3 08 L=50 ~ 750 mm f5 PCD SE73A/B/C/D SAFT LENGT ADJUSTABLE TYPE Vertical mounting Temp. (-0BC ~ 70BC) L ~6mm L ~0mm L ~00mm 4 L=450~ 00 mm f9 f4 f3 4- f5 PCD 08 0 SE74A/B/C/D I-TEMP TYPE orizontal mounting Temp. (-0BC ~ 00BC) PCD 55 f3 f
11 ENCLOSURE NEPSI PROOF No.GYJ0637 Ex d IIC T3~T6 PTB PROOF No. 05 ATEX 09 II G EEx d IIB T3~T6 II D IP65 T3~T6 SE75A/B/C/D SE76A/B/C/D SE77A/B/C/D I-TEMP SAFT I-TEMP SAFT LENGT PROTECTIVE TUBE TYPE ADJUSTABLE TYPE orizontal /Vertical mounting Vertical mounting Temp. (-0BC ~ 00BC) Temp. (-0BC ~ 00BC) CABLE IRE TYPE Vertical mounting Temp. (-0BC ~ 70BC) f3 f3 f L=50~ 750 mm "PF f90 f L=450~ 00 mm f9 f4 f90 PCD f.7 4 L=450~ 4000 mm 0 f4 PCD f Paddle Introduction (Big) A B,C,D (A) x (x), Min. fixed hole diameter size f90mm. (B) 65x80 (x), Directly mounted into " fixed hole. (C) 65x0 (x), Directly mounted into " fixed hole. (D) 80x80 (x) E F 3 (E) 50x (x), Suitable for high S.G. raw material, application by small size paddle to decrease the material flowing impact directly. (F) Scimiter type paddle, Directly screwed through " diameter fixed hole, It Is more easy to be mounted dispense with labor of tank cut-out. 0
12 ORDER INFORMATION SE 7 ( ) MODEL NO. 70 : Screw type 7 : Flange type 7 : Shaft protective tube type 73 : Shaft length adjustable type 74 : i-temp type 75 : i-temp shaft protective tube type 76 : i-temp shaft length adjustable type 77 : Cable wire type VOLTAGE A : 0Vac B : 0Vac C : 40Vac MOUNTING Size for flange or screw C : 3/4" D: " E: -/" F: " G: -/" : 3" PADDLE SAPES I: 4" J: 5" K: 6" S : Others 3 : -/4" Pressure range or other M: 5kg/cm N: 0kg/cm O: 50 Lbs P : 0 Lbs Q: PT R : PF (G) T: BSP U: NPT S : Others A : x (x) B : 65x80 (x) C : 65x0 (x) D : 80x80 (x) E : 50x (x) F : Scimitar S : Others A B,C,D E F 3 LENGT (mm) 0500: below 500mm 0: 50~0mm 500: ~500mm 500mm per Unit Use English letter as first code for probe length over 0m. A50 represents 5m, A00 represents 0m The total length of item will be allowed a tolerance to 6mm. Order Notice. Please make sure the Voltage 4Vac, 0Vac, 0Vac or 40Vac, 50/60 z.. Please make sure the side or top mounting. 3. Please make sure the material specific gravity (S.G.) value. 4. Please make sure whether any bridge block or vibrating motor installed onto the tank wall. Please try to apply our item SA40 capacity sensor. 5. Please make sure the rotary paddle size is available to enter into the flange inlet.
13 [FC/FD] [FG] Mini Float/Magnetic Float Level Switch Magnetic Float Level Transmitter [EA] [LR] [PB] [FF] [FA/FB] [SP] [SF] Side Mounting Float Switch Cable Float Level Switch Thermal Dispersion Flow Switch Paddle Flow Switch [EF] [EB] [EG] [FA/FB] [EB] [EC] [FG] [JFR] [FC/FD] [SB] [SC] [SD] Optical Level Switch [SA] [SE] [SA] Rotary Paddle Level Switch Capacitance Level Switch [FF] [EC] Pressure Level Transmitter [SF] [LR] Loop Power Indicator [SC] [SC] Vibrating Probe Level Switch Tuning Fork Level Switch [SD] [FC/FD] [SP] [EB] RF-Capacitance Level Transmitter [SB] [EG] [EF] [MEF] [EA] [JFR] [EE] RF-Capacitance / Admittance Level Switch Magnetostrictive Level Transmitter By-Pass Level Transmitter Mini By-Pass Level Transmitter Ultrasonic Level Transmitter FMC Radar Level Transmitter Electromechanical Level Measuring System [SC] [SE] [EB] [SB] [EE] [SE] [EA] [SC] [JFR] [EB] [PB/PM] [SA] [SC] [ED] Speed Monitor [SRT/SRS] Conveyer Belt Misalignment Switch & [SB] Safety Cable Pull Switch [PB/PM] Microprocessor Based Bargraphic Display Scaling Meter [BRD/AE] Valve and Controller for Dust Collector System [BAS/BA/BVP] Air ammer [BVK/BVR/BVT] Pneumatic Vibrator [BAS/ BA/BVP] [BVK/ BVR/BVT] FineTek Co., Ltd. No.6, Tzuchiang St., Tucheng Industrial Park, New Taipei City 36, Taiwan TEL: FAX: info@fine-tek.com Fine automation (Shangai) Co., Ltd. No.45 Duui Rd, Minang District, Shanghai, China 009 TEL: FAX: info.sh@fine-tek.com FineTek Pte Ltd. No. Kaki Bukit Road,#04-0 Eunos Technolink 45939, Singapore TEL: FAX: info.sg@fine-tek.com Distributor: FineTeK Gmb Frankfurter Str. 6, OG D-6548 Ruesselsehim, Germany TEL: +49-(0) FAX: +49-(0) info@fine-tek.de 08-SE-B0-EP, 06/0/0
Rotary paddle level switches
Rotary paddle level switches Paab Tekno Trading AB - Tingvallastrand 1, 661 40 Säffle, Sweden Tel: +46 533 150 60 - Fax +46 533 169 31 - info@paab.com - www.paab.com INTRODUCTION PRINCIPLE The SE series
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDE EVE SITC http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall
More informationINTRODUCTION FEATURES
visit our website INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDLE LEVEL SITC PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDE EVE SITC http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall
More informationINTRODUCTION FEATURES WORKING PRINCIPLE
www.fine-tek.com INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationFINE AUTOMATION ROTARY PADDLE LEVEL
FINE AUTOMATION ROTARY PADDE EVE TE: 886--689607, 688605 FAX: 886--689533, 6883318 http: //www.fineautomation.com e-mail: 93@ms15.h inet.net PRINCIPE The RP series operating principle is simple. A unit
More informationThermal Dispersion & Paddle Type Flow Switch. visit our website
Thermal Dispersion & Paddle Type Flow Switch visit our website PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationSérie. Détecteur à palette rotative. Rotary Padle Level Switch
Série SE Détecteur à palette rotative Rotary Padle Level Switch www.direct-mesure. INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery
More informationPressure Switch. visit our website
Pressure Switch visit our website SPST TYPE CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. TYPE Hex length Body material rating
More informationPressure Switch. visit our website
Pressure Switch visit our website SPST TYPE CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. TYPE Hex Length Body rating (Max.)
More informationPressure Level Transmitter.
Pressure Level Transmitter www.fine-tek.com C H 1 C H C H 1 C H PRODUCT INTRODUCTION FEATURES 1. FineTek Models include: extension cable transducer, Anti-corrosive model, flanged models & pressure transducers..
More informationRotary Paddle Level Switch
www.fine-tek.com Rotary Paddle Level Switch INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins
More informationPressure Switch. visit our website
Pressure Switch visit our website SQ24 SPST TYPE CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. TYPE SQ245 Series SQ246 Series
More informationMAIN FUNCTION FEATURES. . D = v t /2
INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to meet the every-day needs of commercial production, as well serving a more specialized
More informationSolid / Liquid Level Measurement for Field Application Pneumatic Vibrator/Air Shocker Solution Temperature Controller/ Counter /Digital Panel Meter
Solid / Liquid Level Measurement for Field Application Pneumatic Vibrator/Air Shocker Solution Temperature Controller/ Counter /Digital Panel Meter By-pass Level Transmitter EF Series Material SUS316,
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationROTARY PADDLE LEVEL SWITCHES
Paddle switch catalogue YC-PSC01 Iss. 03 ROTARY PADDLE LEVEL SWITCES LEVEL SWITCES FOR SOLIDS YCONTROL ROTARY PADDLE LEVEL SWITC YEAR WARRANTY on the motor assembly due to unique design features:- motor
More informationThermal Dispersion Flow Switch.
Thermal Dispersion Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch s probe contains
More informationINTRODUCTION FEATURES PRINCIPLE APPLICATIONS SCHEMATIC DIAGRAM OF THE PRINCIPLES CONSTRUCTION. 1. Sensing Rod 1 3 Ro Ri. 2. Float
INTOUCTION PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown as below). As the float raised or lowered by liquid level, the sensing rod will have a resistance
More informationPRODUCTS GUIDE. Total solutions for monitoring liquid levels in the Marine Industry
PODUCTS GUIDE Total solutions for monitoring liquid levels in the Marine Industry visit our website FineTek Co., Ltd. No.16, Tzuchiang St., Tucheng Industrial Park, New Taipei City 36, Taiwan. TEL: 886
More informationThermal Dispersion & Paddle Type Flow Switch
www.fine-tek.com Thermal Dispersion & Paddle Type Flow Switch PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationISO-9001:2000 certified Aplus Finetek Sensor, Inc.
SE3 Series Compact Rotary Paddle Point Level Sensor ISO-9001:2000 certified Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION PRINCIPLE The SE3 series is a compact rotary paddle point level sensor that uses
More informationROTARY PADDLE LEVEL SWITCHES with 2 year warranty. Paddle switch catalogue HYC-PSC01
ROTARY PADDE EVE SITCES with year warranty Paddle switch catalogue YC-PSC01 YCONTRO ROTARY PADDE EVE SITC YEAR ARRANTY on the motor assembly due to unique design features:- motor shuts off when paddle
More informationFF Series Side Mount Float Level Switch
ISO-9001:000 certified FF Series Side Mount Float Level Switch More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION OPERATING PRINCIPLE The FF Series is a float
More informationCAPACITIVE LEVEL SWITCHES. Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01
CAPACITIVE LEVEL SWITCHES Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01 HYCONTROL CAPACITIVE LEVEL SWITCH RANGE Hycontrol ME capacitive level switches provide simple, accurate and reliable level
More informationCAPACITANCE LEVEL SWITCH
CAPACITANCE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 4 PRINCIPLE The capacitance level switch measuring principle is based on the "capacitance effects".
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationTUNING FORK LEVEL WORKING PRINCIPLE APPLICATION. Solid Level Detection FEATURE. For Liquid: * Water & Solutions * General Purpose Solvent * Petroleum
TUNING FORK LEVEL WORKING PRINCIPLE The tuning fork of level switch operated by using two piezoelectric elements built-in on vibration tube. The first piezoelectric element triggered by pulse signal that
More informationMAGNET FLOAT LEVEL TRANSMITTER
MAGNET FOAT EVE TANSMITTE http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown
More informationSP/SF Series Flow Switches
ISO-9001:2000 certified SP/SF Series Flow Switches More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION SP SERIES OPERATING PRINCIPLE SP SERIES The SP Series
More informationMagnetic Float Level Indicator
Magnetic Float Level Indicator and By-Pass Level Indicator Magnetic Float Level Indicator The "Magnet Float Level Indicator" is composed of the float and sensing rod. As the float raised or lowered by
More informationMINI BY-PASS LEVEL INDICATOR
MINI BY-PASS LEVEL INDICATOR APPLICATIONS AND FEATURES It can be easily observed from the change of the flag color. Safer device comparing to glass type level gauge. Compact type, easy to install. Magnetic
More informationLevel switches Series LC40 Float level switch for liquids
Level switches Series LC40 Float level switch for liquids Simple and robust construction Versatile and easily adaptable to the different control positions of the industrial processes Side or top of the
More informationFINE AUTOMATION SIDE MOUNTING FLOAT SWITCH PRINCIPLE FEATURES WIRING
FINE AUTOMATION SIDE MOUNTING FLOAT SWITCH TEL: 886--6894607, 688605 FAX: 886--6894533, 6883318 http: //www.fineautomation.com e-mail: L93@ms15.hinet.net PRINCIPLE Simple theory as liquid buoyancy is utilized
More informationMetal tube variable area flowmeter for gases, liquids and steam
Metal tube variable area flowmeter for gases, liquids and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h, kg/h, t/h,
More informationMini Magnetic Float Type Level Switch
33 Mini Magnetic Float Type Level Switch Hydraulic Equipment. Lubricating Oils. and Coolant Tanks Introduction SFM series float type liquid level Switch made by Seojin Instech is intended for mounting
More informationMetal tube flowmeters. Series SC250. Metal Tube Flow Meters. Series SC250. Variable area flowmeter for liquids, gases and steam
Metal tube flowmeters Variable area flowmeter for liquids, gases and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h,
More informationAP ATEX AIRPOWER POSITIONERS AP2000 FEATURES AP1000 & AP1200 FEATURES OPTIONS OPTIONS
AP1000-2000 Airpower positioners are a robust range of rotary or linear valve positioners in AP1000 electro-pneumatic (4-20mA), AP1200 pneumatic (3-15 psi) or AP2000 programmable smart type. Designed to
More informationNIVOCONT R VIBRATING ROD LEVEL SWITCHES
For solids NIVOCONT R VIBRATING ROD LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES O U R P R O F E S S NIVOCONT R VIBRATING ROD LEVEL SWITCHES MAIN FEATURES Extension up
More informationEMPOWERING PRECISION WITH ACCURATE SOLUTIONS
INSTRUMENTATION CALIBRATION ENGINEERING www.calconuae.com EMPOWERING PRECISION WITH ACCURATE SOLUTIONS CITY ANCHOR Group Understanding: Striving to become one of the best solution providers, supplier and
More informationMobrey dry products level measurement and control
Product Data Sheet Mobrey offer a range of technologies for reliable point-level detection in a variety of dry solid applications The Mobrey Series PLS is a paddle rotating level switch that detects high
More informationV200 Series Positioners
V200 Series Positioners In a single compact and rugged housing The V200 positioner incorporates the flexibility of converting from a pneumatic unit to several versions of an electropneumatic unit, and
More informationThe Mobrey product range provides reliable point level detection in a variety of dry solid applications
Product Data Sheet June 2015 IP400, Rev DG Mobrey Dry Products Level Measurement and Control The Mobrey product range provides reliable point level detection in a variety of dry solid applications The
More informationROTARY PADDLE TYPE LEVEL SWITCH
ROTRY PDDE TYPE EVE SWITCH N Series Rotary Type NM Series Rotary Type NN Series Reversible Type F-GM Series Rotary Type NNM Series Reversible Type Flame-proof dg Uncomparable models developed based on
More informationfor free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES LEVEL SWITCHES
for free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES MAIN FEATURES MAIN APPLICATION AREAS Level switching of free flowing solids
More informationCABLE FLOAT LEVEL SWITCH
CABLE FLOAT LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 DESCRIPTI The Float Level Switch is made of chemical resistant polypropylene. It is durable,
More informationRS85 Vibrating fork level switch
Data sheet DS/-EN Rev. P Multi-option liquid level switch K-TEK Level products Measurement made easy Features Direct replacement for ultrasonic Gap switches, RF capacitance switches, float switches and
More informationFA/FB Series Cable Float Level Switch
ISO-9001:000 certified FA/FB Series Cable Float Level Switch More than just another level measurement company. Aplus Finetek Sensor, Inc. INTRODUCTI DESCRIPTI The FA/FB series are cable float type level
More informationSS3 Linear / Rotary. Smart Valve Positioner. Smart performance with innovative and ever-strong coil drive even under harsh working environments
Smart Valve Positioner SS3 Linear / Rotary Smart performance with innovative and ever-strong coil drive even under harsh working environments Easy and quick auto-calibration Detecting RA (reverse acting)
More informationMAIN FUNCTION FEATURES. . D = v t /2
ttp e-te com e-ma l o e-te com LT ASONIC LE EL MEAS EMENT Tel -2-22 Fa -2-22 2 INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to
More informationSuper-Safe-Plus Roto-Bin-Dicator
Super-Safe-Plus Roto-Bin-Dicator for your most demanding applications... Offers both mechanical and electronic sensing in one reliable Point Level Sensor... Level control with added confidence Under normal
More informationGlass tube flowmeters Series 6000 Variable area flowmeter for liquids and gases
Glass tube flowmeters Series 6000 Variable area flowmeter for liquids and gases Easy installation Local indication by means of direct reading Low pressure drop Scales directly in l/h, m 3 /h, kg/h, l/min,
More informationAM9000 Series GENERAL FEATURES METAL TUBE VARIABLE AREA FLOWMETER
METAL TUBE VARIABLE AREA FLOWMETER AM9000 Series GENERAL The AM9000 series metal tube variable area flowmeters have the unified face-to-face dimension mm. Having developed the current well-accepted AM7000
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS200 Standard. icenta Controls Ltd
Pointek CLS200 Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level switch with optional rod/cable choices liquids, solids,
More informationLevel Sensors and Switches Guided Radar (TDR) Radar Wave Level Sensors Ultrasonic Level Sensors Rotating Paddle Level Switches Vibrating Fork Level
Level and Switches Level Level Applications Suitable for the applications in the field of chemical plastics, pharmaceutical manufacturing, fodder, grains, cement, fertilizer, powder, fuel materials, hydraulic
More informationPNEUMATIC ACTUATORS. Linear acting
PNEUMATIC ACTUATORS We supply pneumatic double-acting or single-acting with spring return. The actuators are mainly quarterturn actuators for butterflyvalves and ball valves or multiturn for gate valves
More informationHeavy-Duty Pneumatic Actuator. IS & IC Series
Heavy-Duty Pneumatic Actuator BS EN ISO 9001:2000 INTRODUCTION Heavy-Duty Pneumatic Actuator - The IS & IC series of Heavy Duty scotch yoke actuators are designed to suit a wide range of valves and damper
More informationMini-Roto TM Paddle Wheel Installation & Operation Manual
IOM LMR8000 Rev. F Mini-Roto TM Paddle Wheel Installation & Operation Manual Mini-Roto TM Paddle Wheel Installation & Operation Manual CONTENTS I. HANDLING & STORAGE... Inspection and Handling Disposal
More informationDifferential Pressure Gauges Cryo Gauge Model , Cu-alloy Model , Stainless Steel Series
Differential Pressure Gauges Cryo Gauge Model 712.15.160, Cu-alloy Model 732.15.160, Stainless Steel Series Mechanical Pressure Measurement WIKA Data Sheet PM 07.30 Applications Level measurement in closed
More informationTuffy Liquid Level Switches
Tuffy Liquid Level es Tuffy liquid level switches are designed for horizontal mounting in a tank or vessel through threaded or flanged pipe connections. Models are equipped with a single electric or pneumatic
More informationprocess measurement solutions The dry products level control catalogue
process measurement solutions The dry products level control catalogue 1 Dry products level measurement and control from Solartron Mobrey The measurement and control of dry products is important in all
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS200 Standard. 4/18 Siemens FI Overview.
Pointek CLS200 Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level switch with optional rod/cable choices liquids, solids,
More informationRotary Paddle Bin Monitor MODEL KA & KAX
Setting The Standard For Supplier Excellence Rotary Paddle Bin Monitor MODEL KA & KAX Hassle-Free Housing Design - No Bolts! Industry Leading Motor Shut-off Feature Economical, Versatile Point Level Bin
More informationUltrasonic Flow Meter Series Smart-IN US. Features. Description
Features Series 7200 is single-board, self-contained and state-of -the-art ultrasonic flow meter. It has the notable characteristics of high precision, high reliability, high performance, low price etc..
More informationV200 Series Positioners
V200 Series Positioners In a single compact and rugged housing The V200 incorporates the flexibility of converting from a pneumatic unit to several versions of an electropneumatic unit, and the ability
More informationV200 Series Positioners
V200 Series Positioners In a single compact and rugged housing The V200 positioner incorporates the flexibility of converting from a pneumatic unit to several versions of an electropneumatic unit, and
More informationFeatures. Flexibility
The V100 positioner can be ordered as a base model pneumatic positioner, converted to standard NEMA 4X electropneumatic, EX model, or FF (fail freeze) model in a matter of minutes, without removing the
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS300 Standard. 5/42 Siemens FI Overview.
Level Measurement Pointek CLS300 Standard Siemens AG 20 Overview Configuration Installation Pointek CLS300 (standard version) is an inverse frequency shift capacitance level switch with optional rod/cable
More informationCVR-625. Compact Vibrating Rod Instruction Manual
CVR-625 Compact Vibrating Rod Instruction Manual BinMaster: Division of Garner Industries 7201 N. 98th St., Lincoln, NE 68507 402-434-9102 email: info@binmaster.com www.binmaster.com OPERATING INSTRUCTIONS
More informationTemperature Switches. General Instructions
This instruction provides information for mounting, electrical connection, process connection, and calibration of SOR Temperature Switches. The SOR Inc. Temperature Switch consists of a pressure switch
More informationLevel Devices. Rotary Level Indicators Roto-Bin-Dicator
7901 NW 107th Terrace Level Devices We offer Rotary Level Indicators, Radio Frequency Level Indicators, and Turning Fork Level Sensors. For more information please contact your Schenck Process Aftermarket
More informationVALVE ACCESSORIES & CONTROLS V200 POSITIONER A POSITIONER THAT OFFERS IT ALL IN ONE COMPACT, SIMPLE, HOUSING
VALVE ACCESSORIES & CONTROLS V200 POSITIONER A POSITIONER THAT OFFERS IT ALL IN ONE COMPACT, SIMPLE, HOUSING WWW.VACACCESSORIES.COM 205-678-0507 The V200 Positioner Internal I/p with simple loop test points.
More informationElectric Actuated Butterfly Valves Ductile Iron Wafer Body ASME 150# 2 to 6 Pipe
2 to 6 Pipe Features Direct mount wafer butterfly valve with ISO5211 mount 3-layer epoxy coated ductile iron body with 316 SS disc Unique wave line seat reduces torque and extends seal life Visual valve
More informationRHM40. Coriolis Mass Flow Meter for Demanding Applications. Features. Applications. Benefits
RHM40 Coriolis Mass Flow Meter for Demanding Applications Features Standard pressure ratings up to 433 bar (6280 psi) Temperature ratings from -196 to 350 C (-320 to 662 F) Mass flow uncertainty down to
More informationMINI-NBK ECONOMICAL LEVEL INDICATOR
MINI-NBK ECONOMICAL LEVEL INDICATOR Flow Pressure Level Temperature measurement monitoring control N2 316 Stainless Steel Tube Maximum Pressure: 580 PSIG Maximum Temperature: Measuring Lengths to 9.8 Ft.
More informationMagnetic Level Gauges
Magnetic Level Gauges Instrumentation Division > Immediate and accurate response to level changes, giving clear and sharp legibility. > Continuous indication of liquid level. The well proven TC Fluid Control
More informationLevel Measurement Point level measurement - RF Capacitance switches
Pointek CLS200 - Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level and material detection switch with optional rod/cable
More informationInstallation and Operating Manual
. Installation and Operating Manual WE/XE-690, 1350, 1700, 2640, 4400, 5200, 6900, 10500 17500, 25690 1 (Rev. 020113) IOM8011.docx . Table of Contents Introduction Page Safety Instructions..... 3 Introduction
More informationExplosion-protected surface-mounting Thermostat ATH-Ex Series
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationGTV Series High Pressure Control Valves
For primary and secondary shut off of fuel control lines Keeping the World Flowing Contents Section Page Technical Specification 3 ¾" & " 2-Way Poppet Valve 4 ¾" & " 3-Way Poppet Valve 5 /2", 2" & 3" 2-Way
More informationRHM30. Coriolis Mass Flow Meter for Plant and Loading Flows. Features. Applications. Benefits
RHM30 Coriolis Mass Flow Meter for Plant and Loading Flows Features Standard pressure ratings up to 798 bar (11574 psi) Temperature ratings from -196 to 350 C (-320 to 662 F) Mass flow uncertainty down
More informationPaddle Wheel Flow Meter
www.fine-tek.com Paddle Wheel Meter FineTek Lab FineTek is the company who owns a Second lass flow test laboratory in Taiwan. With the most professional R& team, FineTek develops various high precision
More informationAPS & APIS ATEX AIRPOWER SWITCH BOXES FEATURES DESCRIPTION
page 1 DESCRIPTION The switch boxes are suitable for rotary actuators and are the industry leader in versatility, quality and approvals gained. Models include APS standard range with a variety of outputs
More informationLevel instruments. Continuous level measurement - Capacitance transmitters SITRANS LC300. 5/262 Siemens FI Overview.
Overview Configuration is an inverse frequency shift capacitance continuous It is ideal for standard industrial applications in chemical, hydrocarbon processing, food and beverage and mining, aggregate
More informationTECHNICAL BULLETIN. Logix 505si Series Digital Positioner. Experience In Motion FCD LGENTB /13
Logix 505si Series Digital Positioner TECHNICAL BULLETIN FCD LGENTB0505-03 09/13 Experience In Motion Introduction The Logix 505si is a basic positioner for most simple control loops. It is microprocessor
More informationElectric Actuated Butterfly Valves Ductile Iron Lug Body ASME 150# 2 to 6 Pipe with EPS Positioner
2 to 6 Pipe with EPS Positioner Features EPS- Electronic Positioning System with 4-20mA/0-10V input Lug body valve with ISO5211 direct mount actuator 3-layer epoxy coated ductile iron body with 316 SS
More informationMAQ Series Electric Actuator
Series Electric Actuator Series INTRODUCTION KEYVALVE designs, produces and provides high quality actuators and services related to valve automation. - Our long years experience in automation field enables
More informationPOSITIONERS and Controls for Complete Valve Automation
CONTROLS A Division of AT Controls Pneumatic & Electro-Pneumatic POSITIONERS and Controls for Complete Valve Automation 1 SS SERIES SS Features Easy and quick auto-calibration Detecting RA (reverse acting)
More informationLevel Probe multicap DC 16
Technical Information TI 096F/00/en Operating Instructions 017186-1000 Level Probe multicap DC 16 Partially insulated rod probes Applications The Multicap DC 16 probe is primarily designed for limit detection
More informationBGN. All Metal Variable Area Flow Meter. Technical Data Sheet
All Metal Variable Area Flow Meter BGN Technical Data Sheet Extremely robust through star guiding system instead of guiding rod Flow metering of liquids, gases and steam Available up to nominal size of
More informationPoint level measurement Capacitance switches
Pointek CLS300 Standard Overview Configuration Installation Pointek CLS300 (standard version) is an inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output.
More informationDPT TARGET TYPE FLOWMETERS
DPT TARGET TYPE FLOWMETERS Flow Pressure Level Temperature measurement monitoring control S3 Patented Target/Leaf-Spring Design Minimal Wear Components 1.5-8 to 225-500 GPM Water Line Sizes 3/8 to 3" Wide
More informationValve Position Monitors
CONTROLS Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X CONTROLS Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationLevel switch brochure
Level switch brochure Application examples 2 Alarm, measurement and control with Trimod Besta Switch-, flange- and float modules are selected acc. to the process parameters and the desired functions. This
More informationValve Position Monitors
Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X 1 LIMIT SWITCHES Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationElectric Actuator EQ Series
Electric Actuator EQ Series Engineering Creative Solutions for Fluid Systems Since 1901 INTRODUCTION Pratt Industrial designs and provides high quality actuators and services related to valve automation.
More informationOM004, OM006 & OM008 Oval Gear Meter
OM SERIES OM004, OM006 & OM008 Oval Gear Meter OM004 (1/8"), OM006 (1/4") and OM008 (3/8") Oval Gear Meters ACCURACY: ±1.0% OF READING Select Your Body Material: Aluminum or Stainless Steel The OM Small
More information