Level Measurement. Point level measurement Capacitance switches. Pointek CLS300 Standard. 5/42 Siemens FI Overview.

Transcription

1 Level Measurement Pointek CLS300 Standard Siemens AG 20 Overview Configuration Installation Pointek CLS300 (standard version) is an inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Benefits Patented Active-Shield technology so measurement is unaffected by material buildup or nozzle interference in active shield section Performs in extremely abrasive conditions because of solid rod construction Three LED indicators for adjustment control, output status and power High-temperature version up to +400 C (+8 F) Keep unit out of path of falling material, or protect probe from falling material. Build up of material in active shield area does not affect switch operation. Application Pointek CLS300 standard version has three LED indicators with basic relay and solid-state switch alarms. The robust design of CLS300 makes it specifically applicable for heavy solids applications where abrasive materials occur as in the mining industry. The fully potted electronics are unaffected by condensation, dust or vibration. Wetted parts are made of stainless steel with a PFA shield for high chemical resistance, and of ceramic and stainless steel for high temperature version. Materials with low or high dielectric constants can be accurately detected. The unique Active Shield suppresses interference from material buildup or long installation nozzles. The unique modular design of the Pointek CLS300 provides a wide range of configurations, process connections, extensions and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range of probe configurations are available, including rod and cable versions. Key Applications: liquids, slurries, bulk solids, relatively high pressure and temperature, hazardous areas, milling and mining applications Install probe at least 0 (2) from tank wall. Note angle of repose and adjust accordingly. Pointek CLS300 installation, dimensions in mm (inch) min. 0 (2) min. 0 (2) /42 Siemens FI 0 202

2 Siemens AG 20 Level Measurement Pointek CLS300 Standard Technical specifications Mode of operation Measuring principle Inverse frequency shift capacitive level detection Input Measured variable Change in picofarad (pf) Output Output signal Relay output SPDT Form C relay - Max. contact voltage 30 V DC 20 V AC - Max. contact current A (DC) 8 A (AC) - Max. switching capacity 0 W (DC) 2000 VA (AC) - Time delay (ON and/or OFF) s Solid-state output -Output Galvanically isolated - Protection Against reversed polarity (bipolar) - Max. switching voltage 30 V (DC) 30 V peak (AC) - Max. load current 82 ma - Voltage drop < V, typical at 0 ma -Time delay s (pre or post switching) Accuracy Resolution Min. sensitivity (pf) % change in actual capacitance Max. temperature error 0.2 % of actual capacitance value Rated operating conditions ) Installation conditions Location Indoor/outdoor Ambient conditions Ambient temperature C ( F) 2) Medium conditions Liquids, bulk solids, slurries and interfaces, and applications with viscous materials Relative dielectric constant ε r Min.. Process temperature - Rod/Cable version C ( F) 2) - High-temperature version C ( F) Process pressure 3) bar g ( psi g) Design Material (enclosure) Degree of Protection Cable inlet Controls and displays Displays Potentiometers Switches Power supply Supply Certificates and approvals General Purpose Flameproof Enclosure with IS Probe Powder-coated aluminum with gasket Standard: Type 4/NEMA 4/IP6 Optional: Type 4/NEMA 4/IP68 2 x M20x. thread (option: 2 x ½" NPT conduit entry including plugged entry) 3 LEDs, for probe status, output status and power supply 2 potentiometers for time delay and sensitivity DIP switches for delay on/off, fail-safe high/low, time delay test/adjust, high/low sensitivity, test delay settings V AC/DC, Hz, galvanically isolated, 2 W CSA, FM, CE, C-TICK ATEX II /2 G EEx d[ia] IIC T6...T ATEX II /2 D T00 C Dust Ignition Proof with IS Probe ATEX II /2 D T00 C CSA/FM Class II, Div., Gr. E, F, G Explosion Proof Enclosure with IS Probe Marine Overfill Protection Others CSA/FM Class I, Div., Gr. A, B, C, D CSA/FM Class II, Div., Gr. E, F, G Lloyds Register of Shipping, Categories ENV, ENV2 and ENV WHG (Germany) VLAREM II (Belgium) Pattern Approval (China) ) When operation is in areas classified as hazardous, observe restrictions according to relevant certificate. See also Pressure/Temperature curves starting on page /8. 2) Thermal isolator is used if process connection temperature exceeds +8 C (+8 F). 3) Pressure rating of process seal is temperature dependent. See Pressure/Temperature curves starting on page /8. Siemens FI /43

3 Level Measurement Pointek CLS300 Standard Siemens AG 20 Design: Probe Length Sensor wetted parts Rod version High Temperature version Cable version Min. 20 mm (9.8 inch), max. 000 mm (40 inch) PFA (no insulation on active probe), 36L stainless steel, PEEK isolators ) Zirconium Oxide 2) For Caustic Materials, please contact ceg.smpi@siemens.com for alternative O-rings. Min. 20 mm (9.8 inch), max. 000 mm (40 inch) Ceramic (ZrO ) 2 ) isolators (no insulation on active probe), 36L stainless steel Min. 000 mm (40 inch), max mm (984 inch) 36 stainless steel, optional PFA, PEEK isolators O-ring seal material FKM (optional FFKM) 2) Graphite 2) FKM (optional FFKM) 2) Thermal isolator Optional Standard Optional Extension User selectable length User selectable length User selectable cable length /44 Siemens FI 0 202

4 Siemens AG 20 Level Measurement Pointek CLS300 Standard Pointek CLS300 - Standard - Rod Version with Threaded or Flanged process connection C) 7ML Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ¾" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 A G " [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 B G ½" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 D Welded flange, 36L stainless steel, raised face " ASME, 0 lb A " ASME, 300 lb B " ASME, 600 lb C ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 2, PN 6 6 A DN 2, PN 40 6 B DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Standard version, rod 30 mm (3.78 inch) A Extended rod, length 00 mm (9.69 inch) B Extended rod, length 70 mm (29.3 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Standard - Rod Version C) 7ML60- with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Add order code Y0 and plain text: "Insertion length... mm" Extended rod, factory adjusted length E mm ( inch) Extended rod, factory adjusted length F mm ( inch) Extended rod, factory adjusted length G mm ( inch) Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 C (+8 F)] Wetted seals FKM 0 FFKM [for process temperatures above -20 C (-4 F)] Probe material 36L stainless steel with PFA lining and PEEK 0 isolators Approvals Dust Ignition Proof with IS Probe: C CE, C-TICK, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe, with WHG E approval: CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: F Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CE, C-TICK) J General Purpose with WHG approval K (CSA, FM, CE, C-TICK) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - 0 (2 mm threaded, 0 mm flanged) Extended shield - (20 mm threaded, 230 mm flanged) ) Extended shield - (400 mm threaded, 380 mm flanged) 2) 2 ) Available with Probe version options B to D, F, G only [ 00 mm (9.69 inch)] 2) Available with Probe version options C, D, and, G only [ 70 mm (29.3 inch)] C) Subject to export regulations AL: N, ECCN: EAR99. Siemens FI /4

5 Level Measurement Pointek CLS300 Standard Siemens AG 20 Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Pointek CLS300 - Standard - Cable Version C) 7ML6- with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Process connection Threaded, 36L stainless steel ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ½" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 D Welded flange, 36L stainless steel, raised face ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Extended cable, 3000 mm (8. inch), A length can be shortened by customer Extended cable, 6000 mm ( inch), B length can be shortened by customer Add order code Y0 and plain text: "Insertion length... mm" Extended cable, mm E ( inch) Extended cable, mm F ( inch) Extended cable, mm G ( inch) Extended cable, mm H ( inch) Extended cable, mm J ( inch) Extended cable, mm K ( inch) Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 C (+8 F)] /46 Siemens FI 0 202

6 Siemens AG 20 Level Measurement Pointek CLS300 Standard Pointek CLS300 - Standard - Cable Version C) 7ML6- with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Wetted seals FKM 0 FFKM [for process temperatures above -20 C (-4 F)] Probe material Bare 36L stainless steel cable, PEEK isolators and 0 36L stainless steel cable weight PFA coated cable, PEEK isolators and 36L stainless steel cable weight Approvals Dust Ignition Proof with IS Probe: C CE, C-TICK, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe, with WHG E approval: CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: F Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CE, C-TICK) J General Purpose with WHG approval K (CSA, FM, CE, C-TICK) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - 0 (2 mm threaded, 0 mm flanged) Extended shield - (20 mm threaded, 230 mm flanged) ) Extended shield - 2 (400 mm threaded, 380 mm flanged) ) ) Available with Probe version options A, B, F to K, only [ 000 mm (39.7 inch)] C) Subject to export regulations AL: N, ECCN: EAR99. Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Siemens FI /47

7 Level Measurement Pointek CLS300 Standard Siemens AG 20 0 Pointek CLS300 - Standard - High Temperature C) 7ML62- Rod Version with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ¾" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 A G " [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 B G ½" [(BSPP), EN ISO 228-/PF (JIS-P), 3 D JIS B 0202] Welded flange, 36L stainless steel, raised face " ASME, 0 lb A " ASME, 300 lb B " ASME, 600 lb C ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 2, PN 6 6 A DN 2, PN 40 6 B DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Rod 30 mm (3.78 inch) A Extended rod, length 00 mm (9.69 inch) B Extended rod, length 70 mm (29.3 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Standard - High Temperature C) 7ML62- Rod Version with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Add order code Y0 and plain text: "Insertion length... mm" Extended rod, factory adjusted length E mm ( inch) Extended rod, factory adjusted length F mm ( inch) Extended rod, factory adjusted length G mm ( inch) Wetted seals Graphite 0 Probe material 36L stainless steel with ceramic (ZrO 2 ) isolators 0 Approvals Dust Ignition Proof with IS Probe: C CE, C-TICK, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Flameproof Enclosure with IS Probe, with WHG E approval: CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: F Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CE, C-TICK) J General Purpose with WHG approval K (CSA, FM, CE, C-TICK) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - 0 (2 mm threaded, 0 mm flanged) Extended shield - (20 mm threaded, 230 mm flanged) ) Extended shield - 2 (400 mm threaded, 380 mm flanged) 2) ) Available with Probe version options B to D, F, G only [ 00 mm (9.69 inch)] 2) Available with Probe version options C, D, and, G only [ 70 mm (29.3 inch)] C) Subject to export regulations AL: N, ECCN: EAR99H. /48 Siemens FI 0 202

8 Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Siemens AG 20 Level Measurement Pointek CLS300 Standard Siemens FI /49

9 Level Measurement Pointek CLS300 Digital Siemens AG 20 Overview Pointek CLS300 (digital version) is an inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. The digital version includes PROFIBUS PA, an LCD display, and advanced diagnostic features. Application Pointek CLS300 digital version provides an integral LCD display for stand-alone use, with PROFIBUS PA communication (Profile version 3.0, Class B) when required. Solid-state switch alarm is standard. The robust design of CLS300 makes it specifically applicable for heavy solids applications where abrasive materials occur as in the mining industry. The fully potted electronics are unaffected by condensation, dust or vibration. Wetted parts are made of stainless steel with a PFA shield for high chemical resistance, and of ceramic and stainless steel for high temperature version. Materials with low or high dielectric constants can be accurately detected. The unique Active Shield suppresses interference from material buildup or long installation nozzles.08the unique modular design of the Pointek CLS300 provides a wide range of configurations, process connections, extensions and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range of probe configurations are available, including rod and cable versions. Key Applications: liquids, slurries, bulk solids, relatively high pressure and temperature, hazardous areas, milling and mining applications Benefits Patented Active-Shield technology so measurement is unaffected by material buildup or nozzle interference in active shield section Performs in extremely abrasive conditions because of solid rod construction Push-button calibration, full-function diagnostics High sensitivity allows installation in a wide range of liquids, solids or slurry applications Integral LCD display allows for easy menu-driven setup PROFIBUS PA communication (SIMATIC PDM compatible) /0 Siemens FI 0 202

10 Siemens AG 20 Level Measurement Pointek CLS300 Digital Configuration Installation Keep unit out of path of falling material, or protect probe from falling material. Build up of material in active shield area does not affect switch operation. min. 0 (2) min. 0 (2) Install probe at least 0 (2) from tank wall. Note angle of repose and adjust accordingly. Pointek CLS300 installation, dimensions in mm (inch) Siemens FI /

11 Level Measurement Pointek CLS300 Digital Siemens AG 20 Technical specifications Mode of operation Measuring principle Input Measured variable Output Solid-state output Output Protection Max. switching voltage Max. load current Voltage drop Time delay (pre or post switching) Fail-safe mode Connection Accuracy Resolution Min. sensitivity (pf) Max. temperature error Rated operating conditions ) Installation conditions Location Inverse frequency shift capacitive level detection Change in picofarad (pf) Galvanically isolated Against reversed polarity (bipolar) 30 V (DC) 30 V peak (AC) 82 ma < V, typical at 0 ma Programmable by user ( s) Min. or max. Removable terminal block % change in actual capacitance 0.2% of actual capacitance value Indoor/outdoor Ambient conditions Ambient temperature C ( F) 2) Medium conditions Liquids, bulk solids, slurries and interfaces, and applications with viscous materials Relative dielectric constant ε r Min.. Process temperature - Rod/Cable version C ( F) 2) - High Temperature version C ( F) Process pressure 3) bar g ( psi g) Design Material (enclosure) Powder-coated aluminum with gasket Degree of protection Standard: Type 4/NEMA 4/IP6 Optional: Type 4/NEMA 4/IP68 Cable inlet 2 x M20x. thread (option: 2 x ½" NPT conduit entry including plugged entry) Controls and displays Local display LCD Configuration Locally, using 3 button keypad (for standalone operation) Remotely, using SIMATIC PDM (for installation on a network) Power supply Bus voltage (at process connection) Standard: V DC Intrinsically Safe: V DC Current consumption 2. ma Certificates and approvals General Purpose CSA, FM, CE, C-TICK Dust Ignition Proof ATEX II /2 D, 2 D IP6X T00 C Flameproof Enclosure With IS Probe ATEX II /2 G EEx d[ia] IIC T6...T4 ATEX II /2 D T00 C Dust Ignition Proof With IS Probe Intrinsically Safe 4) ATEX II G EEx ia IIC T6...T4 ATEX II /2 D, 2 D IP6X T00 C CSA/FM Class I, Div., Gr. A, B, C, D Non-incendive CSA/FM Class I, Div. 2, Gr. A, B, C, D CSA/FM Class II, Div. 2, Gr. F, G or T6 Explosion Proof with IS Probe CSA/FM Class I, Div., Gr. A, B, C, D Marine Lloyds Register of Shipping, Categories ENV, ENV2 and ENV Others Pattern Approval (China) Communication PROFIBUS PA (IEC 68 CPF3 CP3/2) Bus physical layer: IEC 68-2 MBP-(IS) Device profile: PROFIBUS PA profile for Process Control Devices Version 3.0, Class B FISCO field device ) When operation is in areas classified as hazardous, observe restrictions according to relevant certificate. See also Pressure/Temperature curves starting on page /8. 2) Thermal isolator is used if process connection temperature exceeds +8 C (+8 F) 3) Pressure rating of process seal is temperature dependent. See Pressure/Temperature curves starting on page /8. 4) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection Design: Proble Length Sensor wetted parts Rod version High Temperature version Cable version Min. 20 mm (9.8 inch), max. 000 mm (40 inch) PFA (no insulation on active probe), 36L stainless steel, PEEK isolators ) Zirconium Oxide 2) For Caustic Materials please contact ceg.smpi@siemens.com for for alternative O-rings Min. 20 mm (9.8 inch), max. 000 mm (40 inch) Ceramic (ZrO ) 2 ) isolators (no insulation on active probe), 36L stainless steel Min. 000 mm (40 inch), max mm (984 inch) 36 stainless steel, optional PFA, PEEK isolators O-ring seal material FKM (optional FFKM) 2) Graphite 2) FKM (optional FFKM) 2) Thermal isolator Optional Standard Optional Extension User selectable length User selectable length User selectable cable length /2 Siemens FI 0 202

12 Siemens AG 20 Level Measurement Pointek CLS300 Digital Pointek CLS300 - Digital - Rod with Threaded or C) 7ML660- Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ¾" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 A G " [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 B G ½" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 D Welded flange, 36L stainless steel, raised face " ASME, 0 lb A " ASME, 300 lb B " ASME, 600 lb C ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 2, PN 6 6 A DN 2, PN 40 6 B DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Standard version, rod 30 mm (3.78 inch) A Extended rod, length 00 mm (9.69 inch) B Extended rod, length 70 mm (29.3 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Digital - Rod with Threaded or C) 7ML660- Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Add order code Y0 and plain text: "Insertion length... mm" Extended rod, factory adjusted length E mm ( inch) Extended rod, factory adjusted length F mm ( inch) Extended rod, factory adjusted length G mm ( inch) Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 C (+8 F)] Wetted seals FKM 0 FFKM [for process temperatures above -20 C (-4 F)] Probe material 36L stainless steel with PFA lining and PEEK 0 isolators Approvals Dust Ignition Proof: B CE, C-TICK, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) C CE, C-TICK, ATEX II G EEx ia IIC T6...T4, ATEX II /2 D, 2 D IP6X T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T4, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: E Intrinsically Safe ) F CSA/FM Class I, Div., Gr. A, B, C, D Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CSA, FM, CE, C-TICK) J Enclosure andllid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - 0 (2 mm threaded, 0 mm flanged) Extended shield - (20 mm threaded, 230 mm flanged) 2) Extended shield - 2 (400 mm threaded, 380 mm flanged) 3) ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection 2) Available with Probe version options B to D, F, G only [ 00 mm (9.69 inch)] 3) Available with Probe version options C, D, and, G only [ 70 mm (29.3 inch) inch)] C) Subject to export regulations AL: N, ECCN: EAR99. Siemens FI /3

13 Level Measurement Pointek CLS300 Digital Siemens AG 20 Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Pointek CLS300 - Digital - Cable with Threaded C) 7ML66- or Flanged process connection Versatile inverse frequency shift capacitance level switch with optional process connection choices and configurable output, ideal for detection of liquids, solids, slurries, foam, and interfaces Process connection Threaded, 36L stainless steel ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ½" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 D Welded flange, 36L stainless steel, raised face ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Extended cable, 3000 mm (8. inch), A length can be shortened by customer Extended cable, 6000 mm ( inch), B length can be shortened by customer Add order code Y0 and plain text: "Insertion length... mm" Extended cable, mm E ( inch) Extended cable, mm F ( inch) Extended cable, mm G ( inch) Extended cable, mm H ( inch) Extended cable, mm J ( inch) Extended cable, mm K ( inch) /4 Siemens FI 0 202

14 Siemens AG 20 Level Measurement Pointek CLS300 Digital Pointek CLS300 - Digital - Cable with Threaded C) 7ML66- or Flanged process connection Versatile inverse frequency shift capacitance level switch with optional process connection choices and configurable output, ideal for detection of liquids, solids, slurries, foam, and interfaces Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 C (+8 F)] Wetted seals FKM 0 FFKM [for process temperatures above -20 C (-4 F)] Probe material Bare 36L stainless steel cable, PEEK isolators and 0 36L stainless steel cable weight PFA coated cable, PEEK isolators and 36L stainless steel cable weight Approvals Dust Ignition Proof: B CE, C-TICK, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) C CE, C-TICK, ATEX II G EEx ia IIC T6...T4, ATEX II /2 D, 2 D IP6X T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T4, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: E Intrinsically Safe ) F CSA/FM Class I, Div., Gr. A, B, C, D Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CSA, FM, CE, C-TICK) J Enclosure andllid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - 0 (2 mm threaded, 0 mm flanged) Extended shield - 20 mm threaded, 230 mm flanged) 2) Extended shield - 2 (400 mm threaded, 380 mm flanged) 2) ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection 2) Available with Probe version options A, B and, F to K only [ 000 mm (39.7 inch)] C) Subject to export regulations AL: N, ECCN: EAR99. Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Siemens FI /

15 Level Measurement Pointek CLS300 Digital Siemens AG 20 Pointek CLS300 - Digital - High Temperature Rod version with Threaded or Flanged process connection C) 7ML Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D G ¾" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 A G " [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 B G ½" [(BSPP), EN ISO 228-/PF (JIS-P), JIS B 0202] 3 D Welded flange, 36L stainless steel, raised face " ASME, 0 lb A " ASME, 300 lb B " ASME, 600 lb C ½" ASME, 0 lb D ½" ASME, 300 lb E ½" ASME, 600 lb F 2" ASME, 0 lb G 2" ASME, 300 lb H 2" ASME, 600 lb J 3" ASME, 0 lb K 3" ASME, 300 lb L 3" ASME, 600 lb M 4" ASME, 0 lb N 4" ASME, 300 lb P 4" ASME, 600 lb Q Welded flange, 36L stainless steel, Type A flat faced DN 2, PN 6 6 A DN 2, PN 40 6 B DN 40, PN 6 6 C DN 40, PN 40 6 D DN 0, PN 6 6 E DN 0, PN 40 6 F DN 80, PN 6 6 G DN 80, PN 40 6 H DN 00, PN 6 6 J DN 00, PN 40 6 K (Note: Flange bolting patterns and facings dimensionally correspond to the applicable ASME B6. or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in order code for standard lengths Standard version, rod 30 mm (3.78 inch) A Extended rod, length 00 mm (9.69 inch) B Extended rod, length 70 mm (29.3 inch) C Extended rod, length 000 mm (39.37 inch) D Add order code Y0 and plain text: "Insertion length... mm" Extended rod, factory adjusted length E mm ( inch) Extended rod, factory adjusted length F mm ( inch) Extended rod, factory adjusted length G mm ( inch) Wetted seals Graphite 0 Pointek CLS300 - Digital - High Temperature C) 7ML62- Rod version with Threaded or Flanged process connection Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present. Probe material 36L stainless steel with ceramic (ZrO 2 ) isolators 0 Approvals Dust Ignition Proof: B CE, C-TICK, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) C CE, C-TICK, ATEX II G EEx ia IIC T6...T4, ATEX II /2 D, 2 D IP6X T00 C Flameproof Enclosure with IS Probe: D CE, C-TICK, ATEX II /2 G EEx d[ia] IIC T6...T4, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: E Intrinsically Safe ) F CSA/FM Class I, Div., Gr. A, B, C, D Explosion Proof Enclosure with IS Probe: G CSA/FM Class I, Div., Gr. A, B, C, D General Purpose (CSA, FM) H General Purpose (CSA, FM, CE, C-TICK) J Enclosure andllid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 A 2 x M20x. cable inlet, IP6 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20x. cable inlet, IP68 D Active shield length Standard length - (2 mm threaded, 0 mm flanged) 0 Extended shield - (20 mm threaded, 230 mm flanged) 2) Extended shield - 2 (400 mm threaded, 380 mm flanged) 3) ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection 2) Available with Probe version options B to D, F, G only [ 00 mm (9.69 inch)] 3) Available with Probe version options C, D, and, G only [ 70 mm (29.3 inch)] C) Subject to export regulations AL: N, ECCN: EAR99. /6 Siemens FI 0 202

16 Siemens AG 20 Level Measurement Pointek CLS300 Standard and Digital Order code Further designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [69 x 0 mm (2.7 x.97 inch)]: Y Measuring-point number/identification (max. 6 characters) specify in plain text Acceptance test certificate: Manufacturer's test C certificate M to DIN 30, Part 8 and ISO 9000 Inspection Certificate Type 3. per EN 0204 C2 Operating Instructions Note: The Operating Instructions should be ordered See page /7 as a separate line on the order. This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and manual library. Accessories See page /7 Operating Instructions - Standard English C) 7ML998-JH04 German C) 7ML998-JH33 Note: The Operating Instructions should be ordered as a separate line on the order. Quick Start manual, multi-language C) 7ML998-QY83 This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and Operating Instructions library. Operating Instructions - Digital English C) 7ML998-JJ04 French C) 7ML998-JJ German C) 7ML998-JJ33 Note: The Operating Instructions should be ordered as a separate line on the order. Quick Start manual, multi-language C) 7ML998-XA83 This device is shipped with the Siemens Milltronics manual CD containing the complete ATEX Quick Start and Operating Instructions library. Accessories One metallic cable gland M20x., C 7ML930-AQ ( F) with integrated shield connection (available for PROFIBUS PA) General Purpose /2" NPT General Purpose Cable Entry IP68/IP69K C) AE NEMA6, C ( F), cable size mm ( inch) M20x. General Purpose Cable Entry IP68/IP69K C) AE03223 NEMA6, C ( F), cable size mm ( inch) Hazardous Locations /2" NPT EMC rated Cable Gland: Dust Ignition Proof, AE Flameproof Exd, and Increased Safety ATEX II 2 GD ExtD A2 (Zone,Zone 2, Zone 2, Zone 22, and in Gas Groups IIA,IIB and IIC) C IP66,IP67,IP68, NEMA4X, cable sizes mm ( inch) M20 EMC rated Cable Gland: Dust Ignition Proof, AE Flameproof Exd, and Increased Safety ATEX II 2 GD ExtD A2 (Zone,Zone 2, Zone 2, Zone 22 and in Gas Groups IIA,IIB and IIC) C IP66,IP67,IP68, NEMA4X, cable sizes mm ( inch) Blind threaded flanges are available. Please contact ceg.smpi@siemens.com with a completed application data sheet on page /9 Pointek Specials See page /79 C) Subject to export regulations AL: N, ECCN: EAR99. Siemens FI /7

17 Level Measurement Pointek CLS300 Standard and Digital Characteristic curves Siemens AG 20 Pressure/Temperature Curve CLS300 Extended Rod and Cable Probes Threaded Process Connections (7ML60, 7ML6, 7ML660 and 7ML66) Permitted Operating Pressures P 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) -29 ºC (-20 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) 400 ºC (72 ºF) Permitted Operating Temperature T Example: Permitted operating pressure = 30 bar (43 psi) at 7 C Pointek CLS300 Process Pressure/Temperature derating curves (7ML60, 7ML6, 7ML660 and 7ML66) Pressure/Temperature Curve CLS300 High Temperature Rod Probes Threaded Process Connections (7ML62 and 7ML662) Permitted Operating Pressures P 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) -29 ºC (-20 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) 400 ºC (72 ºF) Permitted Operating Temperature T Pointek CLS300 Process Pressure/Temperature derating curves (7ML62 and 7ML662) /8 Siemens FI 0 202

18 Siemens AG 20 Level Measurement Pointek CLS300 Standard and Digital Pressure/Temperature Curve CLS300 Extended Rod and Cable Probes ASME Flanged Process Connections (7ML60, 7ML6, 7ML660 and 7ML66) Permitted Operating Pressures P 0 bar (72 psi) 40 bar (80 psi) 30 bar (43 psi) ASME 300 lb ) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) ASME 0 lb ) 400 ºC (72 ºF) -29 ºC (-20 ºF) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 Process Pressure/Temperature derating curves (7ML60, 7ML6, 7ML660, and 7ML66) Permitted Operating Pressures P 90 bar (,30 psi) Pressure/Temperature Curve CLS300 HighTemperature Rod Probes ASME Flanged Process Connections (7ML62 and 7ML662) 80 bar (,60 psi) 70 bar (,0 psi) 60 bar (870 psi) ASME 600 lb ) 0 bar (72 psi) 40 bar (80 psi) 30 bar (43 psi) ASME 300 lb ) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) -29 ºC (-20 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) ASME 0 lb ) 400 ºC (72 ºF) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 Process Pressure/Temperature derating curves (7ML62 and 7ML662) Siemens FI /9

19 Level Measurement Pointek CLS300 Standard and Digital Siemens AG 20 Pressure/Temperature Curve CLS300 Extended Rod and Cable Probes EN Flanged Process Connections (7ML60, 7ML6, 7ML660 and 7ML66) Permitted Operating Pressures P 0 bar (72 psi) 40 bar (80 psi) 30 bar (43 psi) PN 40 ) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) 400 ºC (72 ºF) PN 6 ) -29 ºC (-20 ºF) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 Process Pressure/Temperature derating curves (7ML60, 7ML6, 7ML660 and 7ML66) Pressure/Temperature Curve CLS300 High Temperature Rod Probes EN Flanged Process Connections (7ML62 and 7ML662) Permitted Operating Pressures P 0 bar (72 psi) 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) PN 40 ) Atmospheric - bar (-4. psi) -0 ºC (-238 ºF) -00 ºC (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 ºC) (-0 ºC) -0 ºC (-8 ºF) -29 ºC (-20 ºF) 00 ºF (38 ºC) 200 ºF (93 ºC) 0 ºC RT 0 ºC 00 ºC (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 ºC) 0 ºC (302 ºF) 400 ºF (204 ºC) 200 ºC (392 ºF) 00 ºF (260 ºC) 20 ºC (482 ºF) 600 ºF (3 ºC) 300 ºC (72 ºF) 700 ºF (37 ºC) 30 ºC (662 ºF) PN 6 ) 400 ºC (72 ºF) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 Process Pressure/Temperature derating curves (7ML62 and 7ML662) /60 Siemens FI 0 202

20 Siemens AG 20 Level Measurement Pointek CLS300 Standard and Digital Dimensional drawings Rod version Threaded (7ML60 and 7ML660) Lid clip Electronics/ enclosure Lid 20 (0.79) High temperature rod version Threaded (7ML62 and 7ML662) 2 cable entries ½" NPT or M20 x. Y02 ) Thermal isolator M20: 3 (.32) ½" NPT: 0 (.9) Probe Measuring length Y0 (insertion length) min. = 20 (9.8)/max. = 000 (39.37) Ceramic isolator(s) Probe Y02 ) Measuring length Y0 (insertion length) min. = 20 (9.8)/max. = 000 (39.37) 8 (7.28) 7 (6.73) Lid with window Lid without window Thermal isolator 260 (0.24) 273 (0.7) Ø9 (0.7) Ø9 (0.7) Cable version, non-insulated Threaded (7ML6 and 7ML66) Cable version, insulated Threaded (7ML6 and 7ML66) Y02 ) Y02 ) Stainless steel cable Ø6 (0.24) Stainless steel weight 20 (9.84) Measuring length Y0 (insertion length) min. = 00 (20)/max. = 2000 (984) PFA insulated cable Ø0 (0.3) Stainless steel weight 20 (9.84) Measuring length Y0 (insertion length) min. = 00 (20)/max. = 2000 (984) Note: Ø32 (.26) Ø32 (.26) ) Extended Active Shield (Y02): standard length 2 mm (4.92"). Optional active shield lengths: 20 mm (9.84") or 400 mm (.7"). Pointek CLS300 dimensions -Threaded Process connections, dimensions in mm (inch) Siemens FI /6

21 Level Measurement Pointek CLS300 Standard and Digital Siemens AG 20 Rod version Welded flange (7ML60 and 7ML660) lid clip lid High temperature rod version Welded flange (7ML62 and 7ML662) electronics/ enclosure probe Y02 ) measuring length Y0 (insertion length) min. = 20 (9.8)/max. = 000 (39.37) thermal isolator Ceramic isolator(s) probe Y02 ) measuring length Y0 (insertion length) min. = 20 (9.8)/max. = 000 (39.37) 8 (7.28) 2 cable entries ½" NPT or M20 x. 7 (6.73) lid with window lid without window thermal isolator M20: 3 (.32) ½" NPT: 0 (.9) 260 (0.24) 273 (0.7) Ø9 (0.7) Ø9 (0.7) Cable version, non-insulated Welded flange (7ML6 and 7ML66) Cable version, insulated Welded flange (7ML6 and 7ML66) Flange Facing (raised face) Flange Class Facing thickness ASME 0/300 2 (0.08) ASME 600/900 7 (0.28) PN6/40 2 (0.08) stainless steel cable Ø6 (0.24) stainless steel weight 20 (9.84) Y02 ) measuring length Y0 (insertion length) min. = 00 (20)/max. = 2000 (984) PFA insulated cable Ø0 (0.3) stainless steel weight 20 (9.84) Y02 ) measuring length Y0 (insertion length) min. = 00 (20)/max. = 2000 (984) Ø32 (.26) Ø32 (.26) Note: ) Extended Active Shield (Y02): standard length 0 mm (4.3"). Optional active shield lengths: 230 mm (9.06") or 380 mm (4.96"). Insertion length does not include any raised face/gasket face dimension (see Flange Facing Table above) Pointek CLS300 dimensions - Flanged Process connections, dimensions in mm (inch) /62 Siemens FI 0 202

22 Siemens AG 20 Level Measurement Pointek CLS300 Standard and Digital Schematics Wiring: Pointek CLS300 Standard white black red P - + delay switch bank S OFF L2 output status (+) L sensor status 3 2 sensor (f) K P2 K4 trip point GND L3 power on 2 3 power supply 2 to 20 V AC/DC NC NO NO K2 K3 solid state switch: 30 V DC/30 V AC (peak), 82 ma max. relay contact: 8 A at 20 V AC, 2000 VA A at 30 V DC, 0 W Notes: - Identification label is on underside of lid. Switch and Potentiometer settings are for illustration purposes only (Refer to Operation/Setup in manual). - All field wiring must have insulation suitable for at least 20 V. - Relay contact terminals are for use with equipment having no accessible live parts and wiring having insulation suitable for at least 20 V. - Maximum working voltage between adjacent relay contacts shall be 20 V. - Refer to the Instruction Manual or contact Siemens representative for detailed wiring information. Wiring: Pointek CLS300 Digital test input white white reed contact* red (+) alarm output solid-state switch sensor 24 V DC/PROFIBUS PA black (-) orange (f) power connection: 24 V DC or PROFIBUS PA bus (not polarity sensitive). Notes: Refer to the Instruction Manual or contact a Siemens representative for detailed wiring information. *Magnet Activated Sensor Test A magnet can be used to test the sensor without opening the lid of the Pointek CLS300 Digital version. Bring the magnet close to the test area indicated on the enclosure. The sensor test starts and finishes automatically after 0 seconds. Pointek CLS300 connection Siemens FI /63

23 Siemens AG 20 Level Measurement Pontek CLS Specials Selection and ordering data Pointek Specials. See note. CLS00 Polycarbonate Lid and Gasket, FKM Kit, Lid and gasket, CLS00 enclosure version CLS00 Miscellaneous Parts Custom length of cable is available only for 7ML0-xxxx and 7ML0-xxxx CLS200 Gasket (IP6), Synprene F) AE06367 See note 2 Pointek Specials. See note. Kit, Sensor for cable units, PPS, Digital, FKM C) AE Kit, Sensor for cable units, PPS, Standard, C) AE FFKM Kit, Sensor for cable units, PPS, Digital, FFKM C) AE Kit, Sensor for cable units, PVDF, Standard, C) AE06368 FKM Kit, Sensor for cable units, PVDF, Digital, FKM C) AE Kit, Sensor for cable units, PVDF, Standard, FFKM C) AE Kit, Sensor for cable units, PVDF, Digital, FFKM C) AE CLS200 Mounting Bracket, 36L stainless steel Spare gasket, enclosure version (IP6 versions only) F) AE Spare mounting bracket CLS200 PROFIBUS Connector (IP6) AE06368 CLS200 Gasket (IP68), Silicone Spare, PROFIBUS connector (IP6 versions only) AE Spare gasket, enclosure version (IP68 versions) CLS200 Blind Lid F) AE CLS200 Miscellaneous Parts CLS200 with FFKM O-rings (any version) See note 2 CLS200 Electronics Test magnet, digital version 7ML830-JE Amplifier/power supply kit, standard version C) AE03268 Amplifier/power supply, digital version L) 7ML830-JF LCD display, digital version 7ML830-JK Spare aluminum blind lid (for standard versions only) AE CLS300 Cable Extensions, 36L stainless steel CLS200 Lid with window Kit, Stainless steel cable extension, m, adjustable by customer AE Spare aluminum lid with window AE Kit, Stainless steel cable extension, 3 m, adjustable by customer AE CLS200 Sensor Kit for cable units Kit, Stainless steel cable extension, m, adjustable by customer AE Kit, Stainless steel cable extension, 0 m, adjustable by customer AE06369 Kit, Stainless steel cable extension, m, adjustable by customer AE Kit, Sensor for cable units, PPS, Standard, FKM C) AE Kit, Stainless steel cable extension, 20 m, adjustable by customer AE06369 Siemens FI /79