FINE AUTOMATION ROTARY PADDLE LEVEL
|
|
- Muriel McBride
- 5 years ago
- Views:
Transcription
1 FINE AUTOMATION ROTARY PADDE EVE TE: , FAX: , http: // inet.net PRINCIPE The RP series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material present) a synchronous motor rotates the paddle at 1 RPM. hen this paddle rotation is impeded by material, surroanding the paddle, motor will stall and cause the Micro switch to change state. (indicating an alarm or control) APPICATIONS Suitable for powdery producing & processing industries such as plastic, chemical, medical, forage, cement and fertilizer powders. FEATURES Airtight sealing device, outdoor application is available. Unique sealing ring design, it can perform good dust protection to avoid the dust permeate into housing body along with the shaft. The torque force is adjustable. The performance of torsion is stable and reliable. If the rotary paddle bears an extra overload, the motor will be appeared slide to prevent the inside mechanism damaged. It is rationally designed, the inside mechanisms are easily tore down for checking, maintenance and replacement. It doesn't necessary to remove the complete set from the tank. STRUCTURE SAFT CUTC FANGE MOTOR PADDE BODY OI-SEA NUT BEARING MICRO SITC PADDE TYPE EVE SENSOR Paddle Shaft Clutch assembly Body Case TORQUE SPRING Bearing Nut Oil seal Cable Motor Micro Switch MINI PADDE TYPE EVE SENSOR 1
2 INTRODUCTION CONTRO SITC DEVICES ORKING PRINCIPE 1.hen the synchronous motor is turning. It means that material isn't touching the paddles, the (C.) stands for "terminal point connected"..hen material is touching the paddles, (C.) stands for "cut-off", (C.) stands for "connected" the synchronous motor's current is to be cut off. 3.hen the material drops away from the paddles, the synchronous motor runs again and the terminal point is connected, (C.) show that the cycle has begun again. ITE BACK BUE YEO RED M C imit S. NO.1 imit S. NO. TORQUE ADJUSTING MECANISM The torque spring is applied to adjust the shaft output torque force, which is set at "weak" position at factory side, it is adjustable as per customer side target measuring material S.G. (special gravity), if the measured material with higher S.G., please try to release it to more stronger spring force position step until you found the proper orientation. The paddle sensitivity will be interacted by more weaker, otherwise, the low S.G. material will release torque spring to the weakest position, which will cause the paddle performance to be more sensitive. Resetting torque adjusting spring strongest strong weak weakest spring adjusting hole weakest weak strong strongest Terminal strip white black blue red yellow green AC 110V or AC 0V NC COM NO Available : RP10, 0,, 0, 60, 70 AC V or AC 110V or AC 0V Available : RP NC COM NO
3 STANDARD SPECIFICATION 1 Power source : A-110VAC, B-0VAC, C-0VAC, 50/60z 1 Power consumption : 3 1 Contact capacity : SPDT, 5A/50VAC 1 Rotary speed : 1 R.P.M. 1 Insulation test voltage : AC 1500V1minute 1 Torque : 0.5 ~1.0 kg-cm 1 Connect : 1"PF screw or JIS -1/"5kg/cm flange 1 Protection/ material : IP65 / ADC-1 1 Conduit : 1/"PF Specific gravity : 0.5g/cm (b/ft ) RP10A/B/C SCRE TYPE orizontal mounting eight: 1. kg 1"PF RP10A/B/C RP11A/B/C PCD1 RP11A/B/C FANGE TYPE orizontal mounting eight: 1.7 kg RP0A/B/C SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting eight: 1. kg The whole section from flange to paddle are made of SUS Standard ength (option): --50mm (. kg) --500mm (.5 kg) --750mm (.8 kg) 90 1/"PF 10 RP0A/B/C 1/"PF 16 f 10 1/"PF RPA/B/C 1/"PF 118 RPA/B/C SAFT ENGT ADJUSTABE TYPE Vertical mounting Standard ength (option): ~650mm (.5 kg) ~0mm (.8 kg) ~100mm (3.0 kg) 65 PCD1 f7. PCD1 f9 f1.7 f8 3
4 STANDARD SPECIFICATION 1 Power source : A-110VAC, B-0VAC, C-0VAC, 50/60z 1 Power consumption : 3 1 Contact capacity : SPDT, 5A/50VAC 1 Rotary speed : 1 R.P.M. 1 Insulation test voltage : AC 1500V1minute 1 Torque : 0.5 ~1.0 kg-cm 1 Connect : 1"PF screw or JIS -1/"5kg/cm flange 1 Protection/ material : IP65 / ADC-1 1 Conduit : 1/"PF Specific gravity : 0.5g/cm (b/ft ) RP0A/B/C I-TEMP TYPE orizontal mounting Temp. (-10BC ~ 00BC) eight:.1 kg RP0A/B/C PCD1 RP1A/B/C 1/"PF RP1A/B/C I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Temp. (-10BC ~ 00BC) The whole section from flange to paddle are made of SUS Standard ength (option): --50mm (.6 kg) --500mm (.9 kg) --750mm (3. kg) /"PF PCD1 65 f RP6/A/B/C I-TEMP SAFT ENGT ADJUSTABE TYPE Vertical mounting Temp. (-10BC ~ 00BC) Standard ength (option): ~650mm (3 kg) ~0mm (3.3 kg) ~100mm (3.5 kg) RP60/A/B/C CABE IRE TYPE Vertical mounting Standard ength (option): -- 50mm (.5 kg) mm (.8 kg) mm (3 kg) RP6A/B/C 1/"PF 175 PCD1 f9 f1.7 RP60A/B/C 1/"PF PCD1 f6 f8
5 STANDARD SPECIFICATION 1 Power source : A-110VAC, B-0VAC, C-0VAC, 50/60z 1 Power consumption : 3 1 Contact capacity : SPDT, 5A/50VAC 1 Rotary speed : 1 R.P.M. 1 Insulation test voltage : AC 1500V1minute 1 Torque : 0.5 ~1.0 kg-cm 1 Connect : 1"PF screw or JIS -1/"5kg/cm flange 1 Enclosure material : A Alloy, ADC-1 1 Enclosure Protection : Ex d IIB T 1 Conduit : 1/" (std.) or 3/"NPT Specific gravity : 0.5g/cm (b/ft ) RP70A/B/C EXPOSION PROOF SCRE TYPE orizontal mounting RP71A/B/C EXPOSION PROOF FANGE TYPE orizontal mounting RP70A/B/C 1"PF 5 1/"or3/"NPT RP71A/B/C PCD1 1/"or3/"NPT RP7A/B/C EXPOSION PROOF SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Standard ength (option): -- 50mm mm mm RP7A/B/C 15 1/"NPT or 3/"NPT RP73A/B/C 187 1/"NPT or 3/"NPT RP73A/B/C EXPOSION PROOF SAFT ENGT ADJUSTABE TYPE Vertical mounting Standard ength (option): ~650mm ~0mm ~100mm PCD1 - f15 65 f7. 1 PCD1 - f15 f9 f1.7 f8 1 5
6 STANDARD SPECIFICATION 1 Power source : A-110VAC, B-0VAC, C-0VAC, 50/60z 1 Power consumption : 3 1 Contact capacity : SPDT, 5A/50VAC 1 Rotary speed : 1 R.P.M. 1 Insulation test voltage : AC 1500V1minute 1 Torque : 0.5 ~1.0 kg-cm 1 Connect : 1"PF screw or JIS -1/"5kg/cm flange 1 Enclosure material : A Alloy, ADC-1 1 Enclosure Protection : Ex d IIB T 1 Conduit : 1/" (std.) Or 3/"NPT Specific gravity : 0.5g/cm (b/ft ) RP7A/B/C EXPOSION PROOF I-TEMP TYPE orizontal mounting Temp. (-10BC ~ 00BC) - f15 PCD1 RP7A/B/C RP75A/B/C EXPOSION PROOF I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal /Vertical mounting Temp. (-10BC ~ 00BC) 65 1/"or3/"NPT 1 3 PCD1 - f15 f7. RP75A/B/C RP76/A/B/C EXPOSION PROOF I-TEMP SAFT ENGT ADJUSTABE TYPE Vertical mounting Temp. (-10BC ~ 00BC) RP76A/B/C PCD1 - f15 1/"or 3/"NPT Paddle Introduction (Big) f8 f1.7 f /"or 3/"NPT A B,C,D (A) x (x), Min. fixed hole diameter size f90mm. (B) 65x (x), Directly mounted into " fixed hole. (C) 65x10 (x), Directly mounted into " fixed hole. (D) x (x) E F 13 (E) 50x (x), Suitable for high S.G. raw material, application by small size paddle to decrease the material flowing impact directly. (F) Scimiter type paddle, Directly screwed through 1" diameter fixed hole, It Is more easy to be mounted dispense with labor of tank cut-out. 6
7 STANDARD SPECIFICATION 1 Power source : A-110VAC, B-0VAC, C-0VAC, D-VAC 50/60z 1 Power consumption : Contact capacity : AC 50V 3A 1 Rotary speed : 1 R.P.M. 1 Protection/ material : IP65 / PC RPA/B/C/D CROSS-IKE BADE PADDE orizontal mounting eight : 0. kg 0 f6 RPA/B/C/D 7 3/"PF Temp. : -10C ~ 70C 1 Cable length : cm (available for custom length) 1 Torque : ~ kg-cm Specific gravity : 0.3g/cm (0b/ft ) f65 6 f6 RP9CRI 3/"PF 19 7 f65 RP9CR SCIMITAR TYPE PADDE orizontal mounting eight : 0. kg 0.5mm x6c cable Standard length 0mm 133 RP9CR 65 7 SUS 0.5mm x6c cable Standard length 0mm RP9CRI RECTANGE SUS PADDE orizontal mounting eight : 0.8 kg f6 3/"PF RP89CRI f65 0.5mm x6c cable Standard length 0mm RP89CRI I-TEMP TYPE SUS PADDE orizontal / Vertical mounting Temp. Max: 00BC =150~00 18 f6 f1.7 3/"PF f65 f88 Paddle Introduction (Mini) G 0.5mm x6c cable Standard length 0mm I 98 (G) Cross type paddle () Scimitar type paddle, directly ( I ) x (x) material: polycarbonate screwed through 3/" diameter Material: SUS fixed hole. 10 7
8 EXAMPES OF MOUNTING EXAMPES OF MOUNTING TO TANK here the RP10A type paddle cannot be attached to the main shaft from inside the storage tank. The paddle can be set on the main shaft when the distance from the flange face to the tip of paddle is more than 90mm, the relative dimensions being as illustrated right. EXAMPES OF MOUNTING TO TANK The scimitar paddle penetrate through 3/"PF inlet directly like illustrated drawing, then screw tightly. Min.3/"PF 87 Max.5 Min.90 Max.15mm EXAMPES OF MOUNTING TO INJECTION MODING MACINE 8
9 EXAMPE RP1 RP RP0 15B RP10 RP11 INSTAATION NOTICES 1. Please side mount the sensor by inclined 15 B~0 B to decrease the material inflowing impact.. Please select RP0 family items on tank internal operating temperature more than 60 BC. 3. RP10~RP0 on 1"connection pipe inlet, please apply scimitar type to screw directly.. RP, RP6 family items are with flexible and extensible shaft. 9
10 ORDER INFORMATION RP Model 10 : Standard type 0 : Shaft protective tube type : Shaft length adjustable type 0 : i-temp type 60 : Cable wire type 70 : Explosion Proof type : Mini type Voltage A : 110V B : 0V C : 0VAC D : VAC 50/60Z Mounting Size for flange or screw C: 3/" D: 1" E: 1-1/" F: " G: -1/" : 3" I: " J: 5" K: 6" S : Others 3 : 1-1/" RP10~RP70 series: The size of connecting screw is 1". Pressure range or other M: 5kg/cm N : 10kg/cm O : 150 bs P : 0 bs Q: PT R: PF T : BSP S : Others Paddle Shapes RP10~RP70 A : x (x) B : 65x (x) C : 65x10 (x) D : x (x) E : 50x (x) F : Scimitar RP (Mini paddle type) G : Cross type paddle : Scimitar type paddle I : x (x) A B,C,D G 98 E 10 F 13 I ength (mm) RP10~70 : The distance from flange to paddle. RP : ength of cable. The total length of item will be allowed a tolerance to 6mm. Order Notice 1. Please make sure the Voltage VAC, 110VAC, 0VAC or 0VAC, 50/60 z.. Please make sure the side or top mounting. 3. Please make sure the material specific gravity (S.G.) value.. Please make sure whether any bridge block or vibrating motor installed onto the tank wall. Please try to apply our item ME0 capacity sensor. 5. Please make sure the rotary paddle size is available to enter into the flange inlet. 10
ROTARY PADDLE LEVEL SWITCH
ROTARY PADDE EVE SITC http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDE EVE SITC http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDLE LEVEL SITC PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material
More informationRotary paddle level switches
Rotary paddle level switches Paab Tekno Trading AB - Tingvallastrand 1, 661 40 Säffle, Sweden Tel: +46 533 150 60 - Fax +46 533 169 31 - info@paab.com - www.paab.com INTRODUCTION PRINCIPLE The SE series
More informationROTARY PADDLE LEVEL SWITCHES with 2 year warranty. Paddle switch catalogue HYC-PSC01
ROTARY PADDE EVE SITCES with year warranty Paddle switch catalogue YC-PSC01 YCONTRO ROTARY PADDE EVE SITC YEAR ARRANTY on the motor assembly due to unique design features:- motor shuts off when paddle
More informationRotary Paddle Level Switch
Rotary Paddle Level Switch INTRODUCTION PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation
More informationINTRODUCTION FEATURES WORKING PRINCIPLE
www.fine-tek.com INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationROTARY PADDLE LEVEL SWITCHES
Paddle switch catalogue YC-PSC01 Iss. 03 ROTARY PADDLE LEVEL SWITCES LEVEL SWITCES FOR SOLIDS YCONTROL ROTARY PADDLE LEVEL SWITC YEAR WARRANTY on the motor assembly due to unique design features:- motor
More informationINTRODUCTION FEATURES
visit our website INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationSérie. Détecteur à palette rotative. Rotary Padle Level Switch
Série SE Détecteur à palette rotative Rotary Padle Level Switch www.direct-mesure. INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery
More informationRotary Paddle Level Switch
www.fine-tek.com Rotary Paddle Level Switch INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins
More informationCAPACITANCE LEVEL SWITCH
CAPACITANCE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 4 PRINCIPLE The capacitance level switch measuring principle is based on the "capacitance effects".
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationCAPACITIVE LEVEL SWITCHES. Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01
CAPACITIVE LEVEL SWITCHES Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01 HYCONTROL CAPACITIVE LEVEL SWITCH RANGE Hycontrol ME capacitive level switches provide simple, accurate and reliable level
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationTUNING FORK LEVEL WORKING PRINCIPLE APPLICATION. Solid Level Detection FEATURE. For Liquid: * Water & Solutions * General Purpose Solvent * Petroleum
TUNING FORK LEVEL WORKING PRINCIPLE The tuning fork of level switch operated by using two piezoelectric elements built-in on vibration tube. The first piezoelectric element triggered by pulse signal that
More informationISO-9001:2000 certified Aplus Finetek Sensor, Inc.
SE3 Series Compact Rotary Paddle Point Level Sensor ISO-9001:2000 certified Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION PRINCIPLE The SE3 series is a compact rotary paddle point level sensor that uses
More informationFF Series Side Mount Float Level Switch
ISO-9001:000 certified FF Series Side Mount Float Level Switch More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION OPERATING PRINCIPLE The FF Series is a float
More informationFINE AUTOMATION SIDE MOUNTING FLOAT SWITCH PRINCIPLE FEATURES WIRING
FINE AUTOMATION SIDE MOUNTING FLOAT SWITCH TEL: 886--6894607, 688605 FAX: 886--6894533, 6883318 http: //www.fineautomation.com e-mail: L93@ms15.hinet.net PRINCIPLE Simple theory as liquid buoyancy is utilized
More informationROTARY PADDLE TYPE LEVEL SWITCH
ROTRY PDDE TYPE EVE SWITCH N Series Rotary Type NM Series Rotary Type NN Series Reversible Type F-GM Series Rotary Type NNM Series Reversible Type Flame-proof dg Uncomparable models developed based on
More informationSP/SF Series Flow Switches
ISO-9001:2000 certified SP/SF Series Flow Switches More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION SP SERIES OPERATING PRINCIPLE SP SERIES The SP Series
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationMini Magnetic Float Type Level Switch
33 Mini Magnetic Float Type Level Switch Hydraulic Equipment. Lubricating Oils. and Coolant Tanks Introduction SFM series float type liquid level Switch made by Seojin Instech is intended for mounting
More informationThermal Dispersion Flow Switch.
Thermal Dispersion Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch s probe contains
More informationMAGNET FLOAT LEVEL TRANSMITTER
MAGNET FOAT EVE TANSMITTE http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationThermal Dispersion & Paddle Type Flow Switch. visit our website
Thermal Dispersion & Paddle Type Flow Switch visit our website PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationNIVOCONT R VIBRATING ROD LEVEL SWITCHES
For solids NIVOCONT R VIBRATING ROD LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES O U R P R O F E S S NIVOCONT R VIBRATING ROD LEVEL SWITCHES MAIN FEATURES Extension up
More informationMagnetic Float Level Indicator
Magnetic Float Level Indicator and By-Pass Level Indicator Magnetic Float Level Indicator The "Magnet Float Level Indicator" is composed of the float and sensing rod. As the float raised or lowered by
More informationPRODUCTS GUIDE. Total solutions for monitoring liquid levels in the Marine Industry
PODUCTS GUIDE Total solutions for monitoring liquid levels in the Marine Industry visit our website FineTek Co., Ltd. No.16, Tzuchiang St., Tucheng Industrial Park, New Taipei City 36, Taiwan. TEL: 886
More informationThermal Dispersion & Paddle Type Flow Switch
www.fine-tek.com Thermal Dispersion & Paddle Type Flow Switch PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationAP ATEX AIRPOWER POSITIONERS AP2000 FEATURES AP1000 & AP1200 FEATURES OPTIONS OPTIONS
AP1000-2000 Airpower positioners are a robust range of rotary or linear valve positioners in AP1000 electro-pneumatic (4-20mA), AP1200 pneumatic (3-15 psi) or AP2000 programmable smart type. Designed to
More informationPressure Controller. Cataloge K Code Characteristics Index. K00-2 Pressure Controller Brief Introduction
K Pressure Controller Cataloge Code Characteristics Index K00-2 Pressure Controller Brief Introduction KC32 Screw Tube Differential Pressure Controller K01 KY10 Bellows Type Differential Pressure Controller
More informationPNEUMATIC ACTUATORS. Linear acting
PNEUMATIC ACTUATORS We supply pneumatic double-acting or single-acting with spring return. The actuators are mainly quarterturn actuators for butterflyvalves and ball valves or multiturn for gate valves
More informationMINI BY-PASS LEVEL INDICATOR
MINI BY-PASS LEVEL INDICATOR APPLICATIONS AND FEATURES It can be easily observed from the change of the flag color. Safer device comparing to glass type level gauge. Compact type, easy to install. Magnetic
More informationSeries 60. New Smart Positioner. Compact design Convenient & powerful function Enhanced reliability
Series 60 New Smart Positioner Compact design Convenient & powerful function Enhanced reliability J Flow Controls, LLC 14 De Camp Cincinnati, OH 45216 Phone: 513-731-2900 Fax 513-731-6939 www.jflowcontrols.com
More informationMAIN FUNCTION FEATURES. . D = v t /2
ttp e-te com e-ma l o e-te com LT ASONIC LE EL MEAS EMENT Tel -2-22 Fa -2-22 2 INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to
More informationVRF II Series SURPASSING SENSITIVITY FOR THE TOUGHEST APPLICATIONS FEATURES AND BENEFITS STANDARD VS. ADVANCED UNITS
VRF II Series SURPASSING SENSITIVITY FOR THE TOUGHEST APPLICATIONS The VRF II Series uses radio frequency to detect the presence or absence of material in a vessel. It compensates for the load of the probe
More informationRotary Paddle Bin Monitor MODEL KA & KAX
Setting The Standard For Supplier Excellence Rotary Paddle Bin Monitor MODEL KA & KAX Hassle-Free Housing Design - No Bolts! Industry Leading Motor Shut-off Feature Economical, Versatile Point Level Bin
More informationMAIN FUNCTION FEATURES. . D = v t /2
INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to meet the every-day needs of commercial production, as well serving a more specialized
More informationThe Mobrey product range provides reliable point level detection in a variety of dry solid applications
Product Data Sheet June 2015 IP400, Rev DG Mobrey Dry Products Level Measurement and Control The Mobrey product range provides reliable point level detection in a variety of dry solid applications The
More informationROTARY Point Level Measurement for Inventory Control
Measure. Detect. Alert. ROTARY Point Level Measurement for Inventory Control Detect high and low levels while protecting valuable inventory with tried-and-true rotary level indicators from BinMaster. Made
More informationfor free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES LEVEL SWITCHES
for free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES MAIN FEATURES MAIN APPLICATION AREAS Level switching of free flowing solids
More informationValve Position Monitors
CONTROLS Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X CONTROLS Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationPull Cord Switch BX5800. Application
Pull Cord Switch BX5800 Application The Pull Cord Switch is an emergency switch used to stop the belt conveyor instantly when an accident occurs. When an accident occurs or for the normal corrective maintenance,
More informationLIMIT SWITCH BOX MODEL - APL
FEATURES AND BENEFITS Enclosure -Solid design, aluminium die-casting IP67 Painting-Powder coating Housing Body- Aluminium die-casting Quick-set Cam-Easy to set, Splined cam Open Yellow, Close Red Various
More informationElectric Actuated Butterfly Valves Ductile Iron Wafer Body ASME 150# 2 to 6 Pipe
2 to 6 Pipe Features Direct mount wafer butterfly valve with ISO5211 mount 3-layer epoxy coated ductile iron body with 316 SS disc Unique wave line seat reduces torque and extends seal life Visual valve
More informationTuffy Liquid Level Switches
Tuffy Liquid Level es Tuffy liquid level switches are designed for horizontal mounting in a tank or vessel through threaded or flanged pipe connections. Models are equipped with a single electric or pneumatic
More informationElectric Actuated 3-Way Ball Valves T-Port Diverter, Stainless Steel, Full Port 1/4 to 2 NPT
T-Port Diverter, Stainless Steel, Full Port 1/4 to 2 NPT Features Full Port direct mount 316 SS ball valve Functions as a diverter valve 1000 PSI working pressure at 100 F (38 C) Visual valve position
More informationCABLE FLOAT LEVEL SWITCH
CABLE FLOAT LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 DESCRIPTI The Float Level Switch is made of chemical resistant polypropylene. It is durable,
More informationElectric Actuated Ball Valves 150# Flanged Stainless Steel, Full Port 1/2 to 4 inch Pipe
1/2 to 4 inch Pipe Features Direct mount ISO5211 Full Port stainless steel ball valve 2-piece ANSI Class 150 flanged body 275 PSI working pressure at 100 F (38 C) Highly visual dome style valve position
More informationElectric Actuated Ball Valves 3-piece Stainless Steel, Full Port 1/4 to 3 NPT
1/4 to 3 NPT Features Direct mount ISO5211 Full Port stainless steel ball valve 3-piece swing out body designed for easy maintenance 1000 PSI working pressure at 100 F (38 C) Highly visual dome style valve
More informationValve Position Monitors
Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X 1 LIMIT SWITCHES Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationLevel Sensors and Switches Guided Radar (TDR) Radar Wave Level Sensors Ultrasonic Level Sensors Rotating Paddle Level Switches Vibrating Fork Level
Level and Switches Level Level Applications Suitable for the applications in the field of chemical plastics, pharmaceutical manufacturing, fodder, grains, cement, fertilizer, powder, fuel materials, hydraulic
More informationMaterials. Contact Ratings. Conduit Entrances
Features NEMA 1, 3, 4, 4X, 6, 6P, 9 & 13 IP66 and 67 Water tight, dust tight and corrosion resistant for outdoor use For use in hazardous locations: Class I, Div. 1 & 2, Groups C, D Class II, Div. 1 &
More informationECON Limit Switch Box Fig
ECON Limit Switch Box Fig. 79651 Scan for manual Installation & Operation Manual for Limit Switch Box: Fig. 79651 Rev.4 1 Contents Page 1. INTRODUCTION 3 2. SWITCH BOX SPECIFICATION 3 3. SWITCH TYPE SELECTION
More informationITS Series Position Monitoring Switch
ITS Series Position Monitoring Switch Weather Proof ITS series position monitoring switch boxes are primary a rotary position indication device designed to integrate valve and NAMUR rotary pneumatic actuator
More informationV200 Positioner. V200 P Pneumatic Positioner. V200 E Electropneumatic Positioner. Housing Material: Cast aluminium with polyester coating
V200 Positioner Housing Material: Cast aluminium with polyester coating Indicator Options: Flat pointed indicator or raised indicator (red/green or yellow/black) One housing for pneumatic or electropneumatic
More informationSuper-Safe-Plus Roto-Bin-Dicator
Super-Safe-Plus Roto-Bin-Dicator for your most demanding applications... Offers both mechanical and electronic sensing in one reliable Point Level Sensor... Level control with added confidence Under normal
More informationSS3 Linear / Rotary. Smart Valve Positioner. Smart performance with innovative and ever-strong coil drive even under harsh working environments
Smart Valve Positioner SS3 Linear / Rotary Smart performance with innovative and ever-strong coil drive even under harsh working environments Easy and quick auto-calibration Detecting RA (reverse acting)
More informationMetal tube variable area flowmeter for gases, liquids and steam
Metal tube variable area flowmeter for gases, liquids and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h, kg/h, t/h,
More informationLevel Switch MPC2000 MPC2
Technical Information Level Switch MPC2000 MPC2 Displacement Type Level Switch Application MPC series level controllers are displacement type instruments for tank installation. MPC provides 1to 4 control
More informationModel 550 Series Vibration Switches
OPERATION MANUAL Vibration Switches Includes: 550 550M 550-X 550M-X Page 2 SECTION TITLE PAGE 1. INTRODUCTION... 2 2. FEATURES... 3 3. WIRING... 4 4. ANALOG METER... 4 5. TESTING... 4 6. INSTALLATION...
More informationKnow-how makes the difference. Limit Switches
Know-how makes the difference Limit Switches With Dansk Ventil Center as your business partner, you are always guaranteed a wide and well sorted product range and a unique technical know-how Product development
More informationMini-Roto TM Paddle Wheel Installation & Operation Manual
IOM LMR8000 Rev. F Mini-Roto TM Paddle Wheel Installation & Operation Manual Mini-Roto TM Paddle Wheel Installation & Operation Manual CONTENTS I. HANDLING & STORAGE... Inspection and Handling Disposal
More informationATM SERIES THREE PHASE MULTI - TURN
ATM SERIES THREE PHASE MULTI - TURN Manual Operated Wheel Lifting Lugs for Easy Handling Comfort Size Clutch for Manul Operation High Torque Efficiency reversible motor Product Specification Watertight
More informationVALVE POSITION MONITOR APL - SERIES
VALVE POSITION MONITOR APL SERIES Weather proof Explosion proof Special options Patent No. : 0226232, 0383130, 0827347 Design Right No. : 0236743, 0292715, 0292716, 0383546 VALVE AUTOMATION HTLIT 01322L
More informationHKC HM- Series Electric Valve Actuators HM- Series
Actuation&FlowControl HKC Valve Automation Smart & Intelligent Design HM-Series Multi-turn Electric Actuators HKC Co., Ltd 5RA-503, 674-3 Sunggok-Dong, Danwon-Gu, Ansan-Shi, Kyounggi-Do, Republic of Korea
More informationPCVS Series Control Valve Supervisory Switch
Features NEMA 4X* (IP 65) and 6P (IP 67) *Enclosure is 4X. For additional corrosion protection of mounting hardware, use model PCVS-2 CRH -40º to 140º (-40ºC to 60ºC) operating temperature range Visual
More informationInstallation, Maintenance and Operation Manual
Installation, Maintenance and Operation Manual Radius, LLC 4922 Technical Drive Milford, MI 48381 Contents 1. Before operating actuator.. 3 2. About EW actuators 4 1) Internal & external component 2) Internal
More informationMetal tube flowmeters. Series SC250. Metal Tube Flow Meters. Series SC250. Variable area flowmeter for liquids, gases and steam
Metal tube flowmeters Variable area flowmeter for liquids, gases and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h,
More informationD2SW. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
ealed ubminiature Basic witch ealed ubminiature Basic witch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject
More informationLNT SPECIFICATION SHEET 3.4W PER FT. CRI 3.4W IP68 NEON SERIES LED STRIP 50,000 HOURS FEATURES SPECIFICATIONS
NT-65 3.4 IP68 NEON SERIES ED STRIP JOB NAME: OCATION: QUOTE/REF#: SPECIFICATION SEET NT65 is a high performance flexible ED fixture designed as a neon replacement. Suitable for indoor and outdoor applications,
More informationBC 4.2. Tunnel Ventilation Dampers. TVD-GB-40-B Fire Rating 4Hrs As per BS476 Leakage Rating: Class-I As per UL-555S LISTED
BC 4.2 Tunnel Ventilation Dampers TVD-GB-40-B Fire Rating 4Hrs As per BS476 Leakage Rating: Class-I As per UL-555S Type : Tunnel Ventilation Fire Damper Model : TVFD-GB-40-B;TVFD-SB-40-B Fire Rating :
More informationPOSITIONERS and Controls for Complete Valve Automation
CONTROLS A Division of AT Controls Pneumatic & Electro-Pneumatic POSITIONERS and Controls for Complete Valve Automation 1 SS SERIES SS Features Easy and quick auto-calibration Detecting RA (reverse acting)
More informationFlow Switch Paddle Style Flow Switch IF3 1 1 N Paddle style flow switch. Dripproof/Rainproof type. (Equivalent to IP42)
Paddle Style [Option] Flow switches, series IF detect and confirm liquid, generally used in fields such as air conditioning, water supply equipment, etc. Piping sizes ranges from /4B to B. Wide range of
More informationSALIENT FEATURES: Model Model 2000S
DK's magnetic flow switch is the product of two decades knowledge in thermal power station, fertilizer & chemical industries. Flow switch is the target type unit that works on the magnetic principle of
More informationD2SW. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
ealed ubminiature Basic witch ealed ubminiature Basic witch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject
More informationService Instructions. Models: SLC-B & SXLC-B Hopper Level Control
Service Instructions Models: SLC-B & SXLC-B Hopper Level Control Table of Contents GENERAL Page Safety Instructions. 4 Introduction... 5 Warnings.... 5 Installation.. 6 Flexible Mounting Plates.. 7 Horizontal
More informationPRODUCTS CATALOG (2018) TISSIN CO.,LTD. Smart Valve Positioner. Electro-Pneumatic Positioner. Volume Booster. Lock Up Valve. Air Filter Regulator
PRODUCTS CATAOG (08) TISSIN CO.,TD. Smart Valve Positioner Electro-Pneumatic Positioner Volume Booster ock Up Valve Air Filter Regulator Solutions for control valve system About Tissin Solutions for control
More informationINTRODUCTION FEATURES PRINCIPLE APPLICATIONS SCHEMATIC DIAGRAM OF THE PRINCIPLES CONSTRUCTION. 1. Sensing Rod 1 3 Ro Ri. 2. Float
INTOUCTION PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown as below). As the float raised or lowered by liquid level, the sensing rod will have a resistance
More informationInstallation and Operating Manual
. Installation and Operating Manual WE/XE-690, 1350, 1700, 2640, 4400, 5200, 6900, 10500 17500, 25690 1 (Rev. 020113) IOM8011.docx . Table of Contents Introduction Page Safety Instructions..... 3 Introduction
More informationRPPN3 - RPPN7 Industrial pressure switch
Main Features Excellent repeatability Dead band adjustment for regulation Fix dead band for control and alarm Applications Energy safety equipment Power generation safety equipment Pressurized chambers
More informationInstallation, Operation & Maintenance Manual
APL-2 Series Valve Position Monitor Installation, Operation & Maintenance Manual Address : Seonggok-dong, 155, Byeolmang-ro, Danwon-gu, Ansan-si, Gyeonggi-do, South Korea Tel : +82-31-488-8266, Fax : +82-31-488-8269,
More informationFA/FB Series Cable Float Level Switch
ISO-9001:000 certified FA/FB Series Cable Float Level Switch More than just another level measurement company. Aplus Finetek Sensor, Inc. INTRODUCTI DESCRIPTI The FA/FB series are cable float type level
More informationModel 6A00 TECHNICAL BULLETIN 6A00 - TB Inline Deflagration Flame Arrestor
TECHNICAL BULLETIN 6A00 - TB 0-7 ISO Registered Company Model 6A00 Inline Deflagration Flame Arrestor OBJECTIVE The Model 6A00 inline deflagration flame arrestor is a device that can be fitted to the opening
More informationPERFORMANCE IP67 (IEC60529, JIS C 0920) Silver contact: Max.50 mω (6 to 8 Vdc, energizing current 1A, measured by voltage drop method) Gold alloy cros
Waterproof Vertical Type Limit Switches Model VCL-mm 2 sets of SPDT built-in switches enable use as a 2-point detection switch or multi-circuit control switch. On the 2-point detection (center-neutral)
More informationAE Installation Operation & Maintenance Instructions
AE-1400 Installation Operation & Maintenance Instructions IMPORTANT Please read the installation operation and maintenance instruction prior to using any Jomar Valve component. Failure to follow the instructions
More informationD2SW-AQ. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject to water spray or excessive
More informationWYECO. Y-Type Cylinder Actuated Valve. Model WY-C08YT-S
Y-Type Cylinder Actuated Valve Model WY-C08YT-S Model WY-C08YT-F Features Compact, Light weight, High quality High flow capacity Simple design, Easy to assembly Easy to install and maintain All stainless
More informationValves for Panel Mounting
2.2 page 31 2.2 Valves for Panel Mounting Selected models are available for explosion hazardous environment. They are ATEX-Ex certified. For detailed information refer to chapter 2.14. Selected models
More informationModel R7 Rotating Paddle Level Sensor Ideal for powders, solids, and granular material
NOHKEN INC Rotating Paddle Level Sensor Model R7 Rotating Paddle Level Sensor Ideal for powders, solids, and granular material Product Overview R7 is a solid level measurement sensor that is ideal to incorporate
More informationBC 4.3. Gas Tight Dampers GTD-GB40-B-E LISTED
BC 4.3 Gas Tight Dampers GTD-GB40-B-E Table Of Contents S. No Description Page No 1 Gas Tight Damper with Electric Drive 1 2 Electric Drive - Details 2-3 3 Gas Tight Damper with Pneumatic Drive 4 4 Pneumatic
More informationRPPN6 - RPPN8 Industrial pressure switch with high overpressure resistance
Main Features Excellent repeatability Dead band adjustment for regulation Fix dead band for control and alarm Overpressure up to 100 bar Applications Energy safety equipment Power generation safety equipment
More informationInstallation and Operating Instructions Electro-Pneumatic Rotary Positioner SP-21. Description of Device. Part Number System
Description of Device VALMAC Posi-Zest SP-2100 Series is the advanced control device for a rotary control valve that provides unparalleled stability in difficult environments. Easy Maintenance Precise
More informationTOP-QUALITY PNEUMATIC ACTUATOR
TOP-QUALITY PNEUMATIC ACTUATOR BS EN ISO 9001:2000 INTRODUCTION PDS series Pneumatic Actuators are designed using Scotch-Yoke technology from PDS 50 to the largest of PDS 200. Scotch-Yoke technology is
More informationProduct Information Page
CONVERTING OLD A-SERIES PART NUMBERS TO THE NEW A-SERIES PART NUMBERS PIP #: SW-PI-77 Applicable to: With the release of the New A-series product family, Ashcroft has A-Series discontinued the old A-series
More informationPOWER TRANSMISSION. Product range
POWER TRANSMISSION Product range Product range Business Unit Power Transmission Since the firm was established in 1911 by Wilhelm Binder, the Power of Magnetism has always been the essential principle
More informationO-1000 Series ORIFLOMETER MOST COST EFFECTIVE FLOW MEASUREMENT GENERAL STANDARD SPECIFICATIONS TYPES AND FUNCITON
MOST COST EFFECTIVE FLOW MEASUREMENT O-1000 Series ORIFLOMETER GENERAL O-1000 series ORIFLO METER is a flow meter consisting of an orifice plate and a metal tube variable area flow meter. Since the flow
More informationRHM40. Coriolis Mass Flow Meter for Demanding Applications. Features. Applications. Benefits
RHM40 Coriolis Mass Flow Meter for Demanding Applications Features Standard pressure ratings up to 433 bar (6280 psi) Temperature ratings from -196 to 350 C (-320 to 662 F) Mass flow uncertainty down to
More information