TUNING FORK LEVEL WORKING PRINCIPLE APPLICATION. Solid Level Detection FEATURE. For Liquid: * Water & Solutions * General Purpose Solvent * Petroleum

Transcription

1 TUNING FORK LEVEL WORKING PRINCIPLE The tuning fork of level switch operated by using two piezoelectric elements built-in on vibration tube. The first piezoelectric element triggered by pulse signal that created from circuit to transport vibration energy out, and the other piezoelectric element receives the vibration and transmits it to output electric signal. While the probe contacts material, it will cause the frequency change of output signal and the vibration will hold and send out the relay on at the same time. Tuning fork of level switch provides reliable & maintenance-free for bulk solids. Just a simple mounting and calibration procedure that keep your facility in save and monitoring. This device can withstand fiercely lateral loads and static electricity. For friendly use, Fail-safe is equipped as standard to prevent malfunction caused by power shortage. FEATURE 1 Sturdy and durable design. No calibration needed. Special design to avoid the accumulation of material on probe. 1 High / Low fail safe modes 1 Field-operatable in sensitivity adjustment to fit versatile density of material. APPLICATION 1 Most materials in powder can be measurable, includes the grounded coffee, milk power, chocolate, coal ash, bulk, sugar, salt, wheat, grains, glass debris, plastic pellet, cement 1 Sludge level detection in waste water The SC series detects the min. and max of level in bins, silos and hoppers, filled with powdered materials. The following list shows its applications. Solid Level Detection * Powdered milk * Frozen potato chips * Beans * Sugar * Sweets * Coffee beans * Coffee ground * Coffee Powder * Tea * Salt * Flour (in a flour mill) * Foundry sand * Spices * Animal food * Pellets * Peanuts * Tobacco * Wood shavings * Chalk * Stearin chips * Powdered cellulose * Glass finely ground * Granular plastics * Gravel * Powdered clay * Polystyrene powder * Styrofoam * Soda * Soot dry For Liquid: * Water & Solutions * General Purpose Solvent * Petroleum * Oil * Heavy oil * Ink * Liquid Resist * Cream * Drink & Beverage CONSTRUCTURE Vibration Kit Connection Screw Enclosure 1

2 SPECIFICATION ( Multi-Function Tuning Fork Level Switch) f84 f84 Dimensions (Unit:mm) 1" PT f84 1/2"PF 25 f29 1/2"PF 10~250mm.2 1/2"PF 250mm~M Order No. Level Sensor Housing Probe Construction SC400 Standard Type SC410 Tuning Fork Extension Type Aluminum / IP65 SUS 04 / 16 SC4 Tuning Fork Ultra Extension Type Mounting Conduit 1/2"PFx2 Max. Vertical load on rod. 177in.Lbs(Nm) Operating Pressure. -1~600PSI (40BAR) Power Supply ~250,50/60Hz Vac/Vdc Power Consumption 10VA In Ambient Air -40LC~60LC In Bin -40LC~10LC Signal Output Min. material density sensed Time Delay Vibrating Frequency. Fail-safe Sensitivity Relay, SPDT, 5A/250Vac, PNP/NPN(MOSFET) 400mA/60 Vac/ Vdc Solid:density: ³0.07g/cm Liquid:density: ³0.7g/cm Viscosity 1~00 cst 0.6 Second / Operate; 1~ Seconds / Reset 50~70HZ 2

3 SPECIFICATION (Multi-Function Tuning Fork Level Switch) f84 f84 Dimensions (Unit:mm) 1/2"PF 1/2"PF Min.110 Min.110 Order No. Level Sensor Housing Probe Construction SC440 Corrosion Proof Type SUS 04/16 Coating TEFLON Aluminum / IP65 SC450 Sanitary Type SUS 04 / 16 Mounting Flange 1"(min.) 2" Sanitary Conduit Max. Vertical load on rod. Operating Pressure. Power Supply Power Consumption In Ambient Air In Bin Signal Output Min. material density sensed Time Delay Vibrating Frequency. Fail-safe Sensitivity 1/2"PFx2 177in.Lbs(Nm) -1~600PSI (40BAR) ~250,50/60Hz Vac/Vdc 10VA -40LC~60LC -40LC~10LC Relay, SPDT, 5A/250Vac, PNP/NPN(MOSFET) 400mA/60 Vac/ Vdc Solid: density: ³0.07g/cm Liquid: density: ³0.7g/cm Viscosity 1~00 cst 0.6 Second / Operate; 1~ Seconds / Reset 50~70HZ

4 SPECIFICATION f11 f11 Dimensions (Unit:mm) f11 1/2"NPT 1" PT /2"NPT 250mm~M 108 f29 1/2"NPT 10~250mm Order No. SC1400 SC1410 SC14 Model No. Level Sensor Housing Probe Construction MV40 Standard Type MV41 Tuning Fork Extension Type Aluminum / IP65 SUS 04 / 16 MV42 Tuning Fork Ultra Extension Type Mounting Conduit 1/2"NPTx2 Max. Vertical load on rod. Operating Pressure. 177in.Lbs(Nm) -1~600PSI (40BAR) Power Supply ~250Vac/dc Power Consumption 10VA In Ambient Air In Bin -40LC~70LC -40LC~10LC Signal Output Relay, SPDT, 2A/250Vac Max. Min. material density sensed Solid : ³0.07g/cm, Liquid: ³0.7g/cm Time Delay 0.6 Second / Operate; 1~ Seconds / Reset Vibrating Frequency. Fail-safe Sensitivity 50~70HZ 4

5 SPECIFICATION f11 f /2"NPT 108 1/2"NPT Dimensions (Unit:mm) Min.110 Min.110 Order No. SC1540 SC1600 Model No. Level Sensor Housing Probe Construction Mounting MV54 Corrosion-Proof Type SUS 04/16 Coating TEFLON Flange 1"(min.) Aluminum / IP65 MV60 Sanitary Type SUS 04 / 16 2" Sanitary Conduit 1/2"NPTx2 Max. Vertical load on rod. Operating Pressure. Power Supply Power Consumption In Ambient Air In Bin Signal Output Min. material density sensed Time Delay Vibrating Frequency. Fail-safe Sensitivity 177in.Lbs(Nm) -1~600PSI (40BAR) ~250Vac/dc 10VA -40LC~70LC -40LC~10LC Relay, SPDT, 2A/250Vac Max. Solid : ³0.07g/cm, Liquid: ³0.7g/cm 0.6 Second / Operate; 1~ Seconds / Reset 50~70HZ 5

6 SPECIFICATION f8 f8 f8 Dimensions (Unit:mm) Order No. SC2400/10 DIN Connector SC2400/10 ASI Connector SC2400/10 Cable Wire Type Supply Voltage & Output Fork Length In Ambient Air Storage Temp. SC240 :~250Vac / Vdc 2 wire Contactless electronic switch. SC241 :12~55 Vdc wire PNP/ NPN Output. mm -40~60LC -40~70LC In Bin Operation Humidity Operation Pressure Min. material density sensed Magnetic testing Status indication Housing material Fork Material IP Protection Mounting Conduit SC24 SC24 : -40~+LC T: -40~+150LC 80% RH non-condensed Maximum 40 Bar Solid:density: ³0.07g/cm Liquid:density: ³0.7g/cm Viscosity 1~00 cst Output function test performed by putting magnets near the indicated spot Green light indicate power supply Red light indicate operating mode SUS 04 16L, 16, 04 IP65 / IP67 1" PT Valve plug DIN 4650 / Cable connector / ASI 6

7 SPECIFICATION NEPSI PROOF No.GYJ062 Ex d IIC T~T6 PTB PROOF No. 05 ATEX 8 II 2G Ex d IIB T4 II 2D Ex td A21 IP65x T10BC or T9 5BC or T8 0BC f11 f /2"NPT 108 1/2"NPT 1-1/4"PT Dimensions (Unit:mm) 15 1" PT.2 250mm~M Order No. SC1740 SC1741 Model No. Level Sensor Housing Probe Construction Mounting Conduit Max. Vertical load on rod. Operating Pressure. Power Supply Power Consumption In Ambient Air In Bin Signal Output Min. material density sensed Time Delay Vibrating Frequency. Fail-safe Sensitivity MV74 Standard Type Aluminum / Ex d llc T~T6 SUS 04 / 16 1/2"NPTx2 177in.Lbs(Nm) -1~600PSI (40BAR) ~250Vac/dc 10VA -40LC~70LC -40LC~10LC Relay, SPDT, A/250Vac Max. 55~65HZ MV74 Tuning Fork Ultra Extension Type Solid : ³0.07g/cm, Liquid: ³0.7g/cm 0.6 Second / Operate; 1~ Seconds / Reset 1-1/4"PT 7

8 INSTALLATION FOR TUNING FORK 1. Can be applied for high viscosity fluid and power Do not install near around material inlet. 2. Wiring port faces downward recommended..consistence of the wiring port direction and always in downward direction for multi-tuning fork installation. Inlet Vertical Installation: 1. Depends on the sensitivity tuning, user should note the switching point is triggered around 15mm from the tip of fork..consistence of the wiring port direction for multituning fork installation. Do not install near material inlet. 15mm 8

9 TERMINAL / SENSITIVITY ADJUSTMENT (SPDT TYPE) SC1400X, SC1410X, SC14X, SC1540X,SC1600X, SC1740X, SC1741X Relay Output PWR SENSITIVITY SIGNAL FSL FSH L H RT2 RT1 NC COM NO N- L+ SSR(MOSFET) Output ~250VAC ~250VDC RT2 RT1 N- L+ Terminal Function L+, N-: Power Supply NC, COM, No: Relay Output RT1, RT2: Remote-Test : Ground Connection : SSR(MOSFET) Output Fail-Safe High / Low Protection FSH (Fail-Safe High) Protection: Switch to FSH mode. Normal Status: The signal lamp is on. It means that the tuning fork switch does not sense the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. It means that the tuning fork switch is voided and the relay is not conductive. FSL (Fail-Safe Low) Protection: Switch to FSL mode. Normal Status: The signal lamp is on. The tuning fork switch senses the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. The tuning fork switch is voided and the relay is not conductive. Level FSL FSH Panel Function PWR: Power Supply (Green Light) SIGNAL: Output Indication (Red Light) FSH: Power On. The signal lamp is on and the relay is conductive. While the tuning fork switch senses the material, the signal lamp is off and relay is not conductive. FSL: Power On. The signal lamp is off and the relay is not conductive. While the tuning fork switch senses the material, the signal lamp is on and relay is conductive. SENSITIVITY L: Low Sensitivity SENSITIVITY H: High Sensitivity Sensitivity Adjustment The SENSITIVITY is located on the right side of the panel. The user is able to do the minor adjustment by the screw driver. If it turns to H position clockwise, the sensitivity increases; if it turns to L position anti-clockwise, the sensitivity decreases. The sensitivity is originally set at max. value. The switching point is at 15mm from tip of tuning fork switch. The switching point position will be changed by the sensitivity value. If the sensitivity adjusts to lower value, the switching point position is moving backward; if the sensitivity adjusts to high value, the switching point position is moving forward. The changing range of switching point is about 60mm. Contact Form Indication NO COM NC NO COM NC NO COM NC NO COM NC For example, if the switching point needs to be moved backward by 0mm, the user needs to adjust SENSITIVITY anti-clockwise by 10 turns. In general case, it is no need for sensitivity adjustment. Status Fail Normal Normal Fail 9

10 TERMINAL / SENSITIVITY ADJUSTMENT (DPDT TYPE) SC1400X, SC1410X, SC14X, SC1540X,SC1600X, SC1740X, SC1741X Relay Output PWR SENSITIVITY SIGNAL FSL FSH L H RT2 RT1 COM2 NC2 NO2 COM1 NC1 NO1 N- L+ SSR(MOSFET) Output ~250VAC ~250VDC RT2 RT N- L+ Terminal Function L+, N-: Power Supply NC1, COM1, NO1: Relay Output NC2, COM2, NO2: Relay Output RT1, RT2: Remote-Test : Ground Connection Fail-Safe High / Low Protection FSH (Fail-Safe High) Protection: Switch to FSH mode. Normal Status: The signal lamp is on. It means that the tuning fork switch does not sense the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. It means that the tuning fork switch is voided and the relay is not conductive. FSL (Fail-Safe Low) Protection: Switch to FSL mode. Normal Status: The signal lamp is on. The tuning fork switch senses the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. The tuning fork switch is voided and the relay is not conductive. Level Contact Form st : 1 SSR(MOSFET) Output st : 2 SSR(MOSFET) Output FSL NO COM NC NO COM NC NO COM FSH NC NO COM NC Panel Function PWR: Power Supply (Green Light) SIGNAL: Output Indication (Red Light) FSH: Power On. The signal lamp is on and the relay is conductive. While the tuning fork switch senses the material, the signal lamp is off and relay is not conductive. FSL: Power On. The signal lamp is off and the relay is not conductive. While the tuning fork switch senses the material, the signal lamp is on and relay is conductive. SENSITIVITY L: Low Sensitivity SENSITIVITY H: High Sensitivity Sensitivity Adjustment The SENSITIVITY is located on the right side of the panel. The user is able to do the minor adjustment by the screw driver. If it turns to H position clockwise, the sensitivity increases; if it turns to L position anti-clockwise, the sensitivity decreases. The sensitivity is originally set at max. value. The switching point is at 15mm from tip of tuning fork switch. The switching point position will be changed by the sensitivity value. If the sensitivity adjusts to lower value, the switching point position is moving backward; if the sensitivity adjusts to high value, the switching point position is moving forward. The changing range of switching point is about 60mm. For example, if the switching point needs to be moved backward by 0mm, the user needs to adjust SENSITIVITY anti-clockwise by 10 turns. In general case, it is no need for sensitivity adjustment. Indication Status Fail Normal Normal Fail 10

11 TERMINAL / SENSITIVITY ADJUSTMENT (MULTI-FUNCTION TYPE) SC400X, SC410X, SC4X, SC450X Relay Output FSL FSH PWR SENSITIVITY SIGNAL L+ N- NO COM NC PE RT1 RT2 OUTPUT MODE L H SSR(MOSFET) Output L+ N- NG PE RT1 RT2 Terminal Function L+, N-: Power Supply NC, COM, No: Relay Output RT1, RT2: Remote-Test : Ground Connection : SSR(MOSFET) Output Fail-Safe High / Low Protection FSH (Fail-Safe High) Protection: Switch to FSH mode. Normal Status: The signal lamp is on. It means that the tuning fork switch does not sense the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. It means that the tuning fork switch is voided and the relay is not conductive. FSL (Fail-Safe Low) Protection: Switch to FSL mode. Normal Status: The signal lamp is on. The tuning fork switch senses the material and the relay is conductive. Failure: When the power shuts down, the signal lamp is off. The tuning fork switch is voided and the relay is not conductive. Level FSL FSH Panel Function PWR: Power Supply (Green Light) SIGNAL: Output Indication (Red Light) FSH: Power On. The signal lamp is on and the relay is conductive. While the tuning fork switch senses the material, the signal lamp is off and relay is not conductive. FSL: Power On. The signal lamp is off and the relay is not conductive. While the tuning fork switch senses the material, the signal lamp is on and relay is conductive. SENSITIVITY L: Low Sensitivity SENSITIVITY H: High Sensitivity Sensitivity Adjustment The SENSITIVITY is located on the right side of the panel. The user is able to do the minor adjustment by the screw driver. If it turns to H position clockwise, the sensitivity increases; if it turns to L position anti-clockwise, the sensitivity decreases. The sensitivity is originally set at max. value. The switching point is at 15mm from tip of tuning fork switch. The switching point position will be changed by the sensitivity value. If the sensitivity adjusts to lower value, the switching point position is moving backward; if the sensitivity adjusts to high value, the switching point position is moving forward. The changing range of switching point is about 60mm. Contact Form Indication NO COM NC NO COM NC NO COM NC NO COM NC For example, if the switching point needs to be moved backward by 0mm, the user needs to adjust SENSITIVITY anti-clockwise by 10 turns. In general case, it is no need for sensitivity adjustment. Status Fail Normal Normal Fail 11

12 WIRING DIAGRAM DETAILS SC240X (Two wires) wiring Min. Max. Wiring Power can be AC/DC switching. Two wires are connected with terminals (L+/N-) as in Figure 1. Min N- L+ N- L+ Max Brown Black Brown Black Brown Black Yellow Green Figure 1 Two wires wiring Brown Black Yellow Green Min. Black Brown Max. Black Brown Low (Min.) Mode: Pin 1 (Brown) is connected to N-. Pin 2 (Black) is connected to L+ with relay. Pin 4 () connects to tank ground. High (Max.) mode: Pin 1 (Brown) is connected to N-. Pin is connected to pin 2 (Black) to L+ with Relay. Pin 4 () connects to tank ground. PE N- PE N - L+ PE N- L+ L+ PE N- L+ DIN Wiring Diagram ASI Cable Wiring Diagram SC240X (Two wires) wiring PNP NPN Max. Min. Max. Min. Yellow Green Brown Black 1 2 R PE N- L+ Yellow Green Brown Black 1 2 R PE N- L+ Yellow Green Brown Black 1 2 R PE L+ N- DIN Wiring Diagram Yellow Green Brown Black 1 2 PE L+ PNP NPN Max. Min. Max. Min. Black Brown Black Brown Black Brown PEN- L+ PE N- L+ PEL+ N- PE L+ N- ASI Cable Wiring Diagram Figure 2 PNP / NPN Output Wiring Diagram Black Brown N- Wiring Power supply is for DC only. Output is PNP / NPN. Please see Figure 2. PNP wiring High(Max.) Mode: Pin 1(Brown) connects to N-. Pin () connects to L+. To output, it is pin 2. (Black) connects to N- with relay. Pin 4 () connects to tank ground. Low(Min.)Mode: Pin 1 (Brown) connects to N-. Pin 2 (Black) connects to L+. To output, Pin () connects to N- with relay. Pin 4 () should contact to tank ground. NPN wiring High(Max.) Mode: Pin 1 (Brown) connects to L+. Pin () connects to N-. To output, Pin 2 (Black) connects to L+ with relay. Pin 4() should contact to tank ground. Low(Min.)Mode: Pin1 (Brown) connects to L+. Pin 2 (Black) connects to N-. To output Pin () connects to L+ with relay. Pin 4 () should contact to tank ground. 12

13 TUNING AND INDICATION DETAILS Fork Trigger Point SC2409 fork trigger point is shown as Figure below. The testing medium is water(s.g.=1 g/cm ), and its trigger point is about 2mm from the fork tip. If testing medium with S.G (specific gravity) lower than 1g/cm (water), the trigger point would increase. Similarly, the trigger point will downward while the S.G is large than water. Magnetic Test After the switch has installed and power tested, magnetic switch can be performed accordingly. Output status will switch from status of NO. to NC. or NC to NO. and red LED would indicate the vibration status by on / off. When magnet is pulled away from the housing, red LED would return as default while fork continues to vibrate. By this verification, user can confirm the wiring and function are correct or not. S.G.<1g/cm Trigger Point moves upward Magnet Testing point Trigger point S.G.>1g/cm Trigger Point moves downward 2mm S.G.<1g/cm Trigger Point moves upward Sensing spot 10mm S.G.>1g/cm Trigger Point moves downward Output Status for Relay Low (Min.) Mode: Tuning fork switch will be active after seconds while power on. Relay is on NO status and red LED indication is off. When tuning fork is covered by testing medium, the vibration will stop and relay becomes NC status. Red LED indication then is on. High(Max.) Mode: Tuning fork switch will be active after seconds while the power on. Relay is on NC status and red LED indication is on. When tuning fork covered by testing medium, the vibration stops and relay becomes NO status. Red LED indication is on. Output Status for PNP / NPN Transistor Low(Min.) Mode : Tuning fork switch will be active after seconds while power on. Output transistor is on NO status and red LED indication is off. When tuning fork covered by testing medium, vibration will stop and output transistor becomes NC status. Red LED indication is on. High(Max.) Mode: Tuning fork switch will be active after seconds while power on. Output transistor is on NC status and red LED indication is on. When tuning fork covered by testing medium, vibration will stop and output transistor becomes NO status. Red LED indication is off. Min. Mode Max.Mode Min. Mode Max.Mode Level Level Contactless electronic switch Switch open Switch closed Switch closed Switch open PNP/ NPN Output Switch open Switch closed Switch closed Switch open Red LED Red LED 1

14 ORDER INFORMATION ORDER NO. 400: Multi-Function Tuning Fork Standard Type 410: Multi-Function Tuning Fork Extension Type 4: Multi-Function Tuning Fork Ultra Extension Type 440: Multi-Function Tuning Fork Corrosion Proof Type 450: Multi-Function Tuning Fork Sanitary Type 1400: MV40 Tuning Fork Standard Type 1410: MV41 Tuning Fork Extension Type 14:MV42 Tuning Fork Ultra Extension Type 1540: MV54 Tuning Fork Corrosion Proof Type 1600: MV60 Tuning Fork Sanitary Type 1740: MV74 Explosion Proof Tuning Fork Standard Type 1741: MV74 Explosion Proof Tuning Fork Ultra Extension Type POWER & OUTPUT MODULE ~250Vac/ Vdc, 50/60Hz MATERIAL 0: SUS04 6: SUS16 P: PTFE R: Relay O/P (Green terminal)-eurotype N: Transistor PNP/NPN-EuroType ( ) ( ) CONNECTION Dimension D---1"(25A) /4"(2A) E---1-1/2"(40A) F---2"(50A) G---2-1/2"(65A) H---"(80A) I---4"(A) J---5"(125A) K---6"(150A) S---others 2 M---5kg/cm N---10kg/cm O Lbs P---00 Lbs Q---PT R---PF(G) T---BSP U---NPT W---PN 10 X---PN 16 Specification 2 Y---PN 25 Z---PN 40 S---others 9---Sanitary LENGTH (L) (UNIT: cm) 0500: below 500mm 0: 501~0mm 1500: 1~1500mm 500mm per Unit Use English letter as first code for probe length over 10m. A150 represents 15m, A0 represents m BEFORE YOU ORDER 1. Please affirm the voltage. 2. Please affirm the mounting positions.. Please affirm the material specific gravity (S.G.) value. 4. Please affirm whether any bridge block or vibrating motor are attached onto the silo wall. Tolerance of the total product length is 5mm Characteristics, specifications and dimensions are subject to change without notice. Please contact your nearest distributing office for further information. 14

15 ORDER INFORMATION POWER SUPPLY & OUTPUT 0: ~250Vac / Vdc 2 wire Contactless electronic switch. 1: 12~55 Vdc wire PNP/ NPN Output. MATERIAL 0: SUS04 6: SUS16 L: SUS16L MODEL 0: Standard (High temp. 150 C) ELECTRICAL CONNECTION A: ASI C: CABLE D: Valve plug DIN4650 CONNECTION Dimension D---1"(25A) E---1-1/2"(40A) F---2"(50A) G---2-1/2"(65A) H---"(80A) I---4"(A) J---5"(125A) K---6"(150A) S---Special 2 M---5kg/cm N---10kg/cm O Lbs P---00 Lbs Q---PT R---PF(G) T---BSP U---NPT W---PN 10 X---PN 16 Specification 2 SC 24 0 Y---PN 25 Z---PN 40 S---Special 15