ROTARY PADDLE LEVEL SWITCH
|
|
- Anne Day
- 5 years ago
- Views:
Transcription
1 ROTARY PADDE EVE SITC http: // Tel: Fax: PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material present) a synchronous motor rotates the paddle at RPM. hen this paddle rotation is impeded by material, surrounding the paddle, motor will stall and cause the Micro-switch to change state. (indicating an alarm or control) APPICATIONS Suitable for powdery producing & processing industries such as plastic, chemical, medical, forage, cement and fertilizer powders. FEATURES Airtight sealing device, outdoor application is available. Unique sealing ring design, it can perform good dust protection to avoid the dust permeate into housing body along with the shaft. The torque force is adjustable. The performance of torsion is stable and reliable. If the rotary paddle bears an extra overload, the motor will be appeared slide to prevent the inside mechanism damaged. It is rationally designed, the inside mechanisms are easily tore down for checking, maintenance and replacement. It doesn't necessary to remove the complete set from the tank. Very suitable for small tank and material of low density STRUCTURE SAFT FANGE CUTC MOTOR PADDE BODY OI-SEA NUT BEARING MICRO SITC STANDARD TYPE Paddle Shaft Clutch assembly Body Case TORQUE SPRING Bearing Nut Oil seal Cable Motor Micro Switch MINI TYPE
2 ORKING PRINCIPE & TORQUE ADJUSTING CONTRO SITC DEVICES ORKING PRINCIPE.hen the synchronous motor is turning. It means that material isn't touching the paddles, the (C.) stands for "terminal point connected"..hen material is touching the paddles, (C.) stands for "cut-off", (C.) stands for "connected" the synchronous motor's current is to be cut off. 3.hen the material drops away from the paddles, the synchronous motor runs again and the terminal point is connected, (C.) show that the cycle has begun again. ITE BACK BUE YEO RED M C imit S. NO. imit S. NO. TORQUE ADJUSTING MECANISM The torque spring is applied to adjust the shaft output torque force, which is set at "weak" position at factory side, it is adjustable as per customer side target measuring material S.G. (special gravity), if the measured material with higher S.G., please try to release it to more stronger spring force position step until you found the proper orientation. The paddle sensitivity will be interacted by more weaker, otherwise, the low S.G. material will release torque spring to the weakest position, which will cause the paddle performance to be more sensitive. Do not tamper with the spring as it may cause the Rotary Paddle to be malfunction. Resetting torque adjusting spring strongest strong weak weakest spring adjusting hole weakest weak strong strongest Terminal strip white black blue red yellow green 0Vac or 0Vac NC COM NO Available: SE0, 0,, 0, 60, 70 Vac or 0Vac or 0Vac or 0Vac NC COM NO Available: SE
3 STANDARD SPECIFICATION Power source : A-0Vac, B-0Vac, C-0Vac, 50/60z Power consumption : 3 Contact capacity : SPDT, 5A/50Vac Rotary speed : R.P.M. Insulation test voltage : AC 500Vminute Torque : 0.5 ~.0 kg-cm Connect : "PF screw or JIS -/"5kg/cm flange Protection/ material : IP65 / ADC- Conduit : /"PF 3 3 Specific gravity : 0.5g/cm (b/ft ) Order No. SE0A/B/C Model No. RP0A/B/C SCRE TYPE orizontal mounting eight:. kg Order No. SEA/B/C Model No. RPA/B/C FANGE TYPE orizontal mounting eight:.7 kg Order No. SE0A/B/C Model No. RP0A/B/C SAFT PROTECTIVE TUBE TYPE orizontal / eight:. kg The whole section from flange to paddle are made of SUS --50mm (. kg) --500mm (.5 kg) --750mm (.8 kg) SE0A/B/C "PF 05 /"PF 0 SE0A/B/C /"PF 6 SEA/B/C PCD f 0 /"PF SEA/B/C /"PF 8 Order No. SEA/B/C Model No. RPA/B/C SAFT ENGT ADJUSTABE TYPE ~650mm (.5 kg) ~0mm (.8 kg) ~00mm (3.0 kg) 65 PCD f7. PCD f9 f.7 f8 3
4 STANDARD SPECIFICATION Power source : A-0Vac, B-0VacC, C-0Vac, 50/60z Power consumption : 3 Contact capacity : SPDT, 5A/50Vac Rotary speed : R.P.M. Insulation test voltage : AC 500Vminute Torque : 0.5 ~.0 kg-cm Connect : "PF screw or JIS -/"5kg/cm flange Protection/ material : IP65 / ADC- Conduit : /"PF 3 3 Specific gravity : 0.5g/cm (b/ft ) Order No. SE0A/B/C Model No. RP0A/B/C I-TEMP TYPE orizontal mounting Temp. (-0BC ~ 00BC) eight:. kg Order No. SEA/B/C Model No. RPA/B/C I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal / Temp. (-0BC ~ 00BC) The whole section from flange to paddle are made of SUS --50mm (.6 kg) --500mm (.9 kg) --750mm (3. kg) SE0A/B/C PCD /"PF PCD SEA/B/C 65 f7. /"PF 75 Order No. SE6A/B/C Model No. RP6A/B/C I-TEMP SAFT ENGT ADJUSTABE TYPE Temp. (-0BC ~ 00BC) ~650mm (3 kg) ~0mm (3.3 kg) ~00mm (3.5 kg) Order No. SE60A/B/C Model No. RP60A/B/C CABE IRE TYPE -- 50mm (.5 kg) mm (.8 kg) mm (3 kg) SE6A/B/C /"PF 75 PCD f9 f.7 SE60A/B/C /"PF 8 PCD f6 f8
5 STANDARD SPECIFICATION Power source : A-0Vac, B-0Vac, C-0Vac, D-Vac 50/60z Power consumption :.5 Contact capacity : 3A/50Vac Rotary speed : R.P.M. Protection/ material : IP65 / PC Temp. : -0C ~ 70C Cable length : cm (available for custom length) Torque : ~ kg-cm 3 3 Specific gravity : 0.3g/cm (0b/ft ) Order No. SEA/B/C/D Model No. RPA/B/C/D CROSS-IKE BADE PADDE orizontal mounting eight : 0. kg Order No. SE9CRI Model No. RP9CRI RECTANGE SUS PADDE orizontal mounting eight : 0.8 kg Order No. SE9CR Model No. RP9CR SCIMITAR TYPE PADDE orizontal mounting eight : 0. kg Order No. SE89CRI Model No. RP89CRI I-TEMP TYPE SUS PADDE orizontal / Temp. Max: 00BC 0 f6 SEA/B/C/D 7 3/"PF 75 f65 0.5mm x6c cable Standard length 0mm 33 f /"PF 6 f6 3/"PF =50~00 60 f6 f.7 SE9CR SE89CRI 3/"PF 7 SE9CRI SUS 9 7 f65 0.5mm x6c cable Standard length 0mm f65 0.5mm x6c cable Standard length 0mm f65 f88 Paddle Introduction (Mini) G 0.5mm x6c cable Standard length 0mm I 98 (G) Cross type paddle () Scimitar type paddle, directly ( I ) x (x) material: PC screwed through 3/" diameter Material: SUS fixed hole. Material: PC 0 5
6 EXAMPES OF MOUNTING EXAMPES OF MOUNTING TO TANK here the SE0A type paddle cannot be attached to the main shaft from inside the storage tank. The paddle can be set on the main shaft when the distance from the flange face to the tip of paddle is more than 90mm, the relative dimensions being as illustrated right. The scimitar paddle penetrate through 3/"PF inlet directly like illustrated drawing, then screw tightly. INSTAATION EXAMPE FOR INJECTION MODING MACINE Steps to Install the Injection Molding Machine Injection Molding Machine usually use SE Install the Rotary Paddle through a Dia. f0mm ole on the Silo Remove the paddle from the device by taking out the fastening pin Insert the SE through the mounting hole and tighten it After which, secure the Paddle to the SE by locking it to the shaft with the the pin Keep in mind to 'widen' the opening of the pin in order to secure it 6
7 EXAMPE SE SE SE0 5 SE0 SE INSTAATION NOTICES. Please side mount the sensor by inclined 5 B~0 B to decrease the material inflowing impact.. For igh Temperature application whereby the temperature inside the tank is more than 70BC Please use SE9 Series. 3. SE0~SE0 on " connection pipe inlet, please apply scimitar type to screw directly.. SE, SE6 family items are with flexible and extensible shaft. 5. Please ensure that the Cable Gland point downwards and the nut must be fastened to secure the device. 7
8 ORDER INFORMATION 9 : Standard type 0 : Shaft protective tube type : Shaft length adjustable type 9 : i-temp type VOTAGE A : 0Vac B : 0Vac C : 0Vac D : Vac 50/60Z MOUNTING 60 : Cable wire type 89 : Mini type Size for flange or screw Pressure range or other C: 3/" D: " E: -/" F: " G: -/" : 3" I: " J: 5" K: 6" S : Others 3 : -/" SE0~SE60 series: The size of connecting screw is ". M: 5kg/cm N: 0kg/cm O: 50 bs P: 0 bs Q: PT R: PF T: BSP U: NPT S: Others PADDE SAPES SE0~SE60 A : x (x) B : 65x (x) C : 65x0 (x) D : x (x) E : 50x (x) F : Scimitar A B,C,D G E F 3 I SE (Mini paddle type) G : Cross type paddle : Scimitar type paddle I : x (x) ENGT (mm) SE0~60 : The distance from flange to paddle. SE : ength of cable. The total length of item will be allowed a tolerance to A6mm Material:PC Material:PP Material:SUS Order Notice. Please make sure the Voltage Vac, 0Vac, 0Vac or 0Vac, 50/60 z.. Please make sure the side or top mounting. 3. Please make sure the material specific gravity (S.G.) value.. Please make sure whether any bridge block or vibrating motor installed onto the tank wall. Please try to apply our item SA0 capacitance level sensor. 5. Please make sure the rotary paddle size is available to enter into the flange inlet. 8
9 ENCOSURE Power source : A-0Vac, B-0Vac, C-0Vac, 50/60z Power consumption : 3 Contact capacity : SPDT, 3A/50Vac Rotary speed : R.P.M. Insulation test voltage : AC 500Vminute Torque : 0.5 ~.0 kg-cm NEPSI PROOF No.GYJ0337 Ex d IIB T3~T6 PTB PROOF No. 05 ATEX 09 II G EEx d IIB T3~T6 II D IP65 T3~T6 Connect : "PF screw or flange "~6" -/"5kg/cm (std.) Enclosure material : A Alloy, ADC- Enclosure Protection : Ex d IIB T~T6 Conduit : /" (std.) or 3/"NPT 3 3 Specific gravity : 0.5g/cm (b/ft ) Order No. SE70A/B/C/D Model No. RP70A/B/C/D SCRE TYPE orizontal mounting "PF Order No. SE7A/B/C/D Model No. RP7A/B/C/D FANGE TYPE orizontal mounting f3 Order No. SE7A/B/C/D Model No. RP7A/B/C/D SAFT PROTECTIVE TUBE TYPE orizontal / -- 50mm mm mm 0 =50 ~ 750 mm f3 "PF 08 f3 - f5 PCD Order No. SE73A/B/C/D Model No. RP73A/B/C/D SAFT ENGT ADJUSTABE TYPE ~650mm ~0mm ~00mm 0 f Order No. SE7A/B/C/D Model No. RP7A/B/C/D I-TEMP TYPE orizontal mounting Temp. (-0BC ~ 00BC) f PCD f3 =50~ 00 mm f9.5 f - f5 PCD 85 f90 9
10 ENCOSURE Order No. SE75A/B/C/D Model No. RP75A/B/C/D I-TEMP SAFT PROTECTIVE TUBE TYPE orizontal / Temp. (-0BC ~ 00BC) NEPSI PROOF No.GYJ0337 Ex d IIB T3~T6 PTB PROOF No. 05 ATEX 09 II G EEx d IIB T3~T6 II D IP65 T3~T6 Order No. SE76A/B/C/D Model No. RP76A/B/C/D I-TEMP SAFT ENGT ADJUSTABE TYPE Temp. (-0BC ~ 00BC) Order No. SE77A/B/C/D Model No. RP77A/B/C/D CABE IRE TYPE Temp. (-0BC ~ 00BC) f3 f3 f "PF f90 f7. 5 f90 f 0 =50~ 750 mm =50~ 00 mm f9.5 f PCD f.7 =50~ 000 mm PCD f9.5 f8 08 f Paddle Introduction (Big) A B,C,D (A) x (x), Min. fixed hole diameter size f90mm. (B) 65x (x), Directly mounted into " fixed hole. (C) 65x0 (x), Directly mounted into " fixed hole. (D) x (x) E F 3 (E) 50x (x), Suitable for high S.G. raw material, application by small size paddle to decrease the material flowing impact directly. (F) Scimiter type paddle, Directly screwed through " diameter fixed hole, It Is more easy to be mounted dispense with labor of tank cut-out. 0
11 ORDER INFORMATION 70 : RP70 Screw type 7 : RP7 Flange type 7 : RP7 Shaft protective tube type 73 : RP73 Shaft length adjustable type VOTAGE A : 0Vac B : 0Vac C : 0Vac D : Vac 50/60Z MOUNTING 7 : RP7 i-temp type 75 : RP75 i-temp shaft protective tube type 76 : RP76 i-temp shaft length adjustable type 77 : RP77 Cable wire type Size for flange or screw C: 3/" D: " E: -/" F: " G: -/" : 3" PADDE SAPES I: " J: 5" K: 6" S : Others 3 : -/" Pressure range or other M: 5kg/cm N: 0kg/cm O: 50 bs P: 0 bs Q: PT R: PF T: BSP U: NPT S: Others A : x (x) B : 65x (x) C : 65x0 (x) D : x (x) E : 50x (x) F : Scimitar A B,C,D E F 3 ENGT (mm) The total length of item will be allowed a tolerance to 6mm. Order Notice. Please make sure the Voltage Vac, 0Vac, 0Vac or 0Vac, 50/60 z.. Please make sure the side or top mounting. 3. Please make sure the material specific gravity (S.G.) value.. Please make sure whether any bridge block or vibrating motor installed onto the tank wall. Please try to apply our item SA0 capacity sensor. 5. Please make sure the rotary paddle size is available to enter into the flange inlet.
ROTARY PADDLE LEVEL SWITCH
ROTARY PADDE EVE SITC http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PRINCIPE The SE series operating principle is simple. A unit is usually located through a bin wall
More informationFINE AUTOMATION ROTARY PADDLE LEVEL
FINE AUTOMATION ROTARY PADDE EVE TE: 886--689607, 688605 FAX: 886--689533, 6883318 http: //www.fineautomation.com e-mail: 93@ms15.h inet.net PRINCIPE The RP series operating principle is simple. A unit
More informationROTARY PADDLE LEVEL SWITCH
ROTARY PADDLE LEVEL SITC PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation (no material
More informationRotary paddle level switches
Rotary paddle level switches Paab Tekno Trading AB - Tingvallastrand 1, 661 40 Säffle, Sweden Tel: +46 533 150 60 - Fax +46 533 169 31 - info@paab.com - www.paab.com INTRODUCTION PRINCIPLE The SE series
More informationRotary Paddle Level Switch
Rotary Paddle Level Switch INTRODUCTION PRINCIPLE The SE series operating principle is simple. A unit is usually located through a bin wall at the top, middle or low level of a bin. During normal operation
More informationINTRODUCTION FEATURES WORKING PRINCIPLE
www.fine-tek.com INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationINTRODUCTION FEATURES
visit our website INTRODUCTION ORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins and containers. The unit is
More informationROTARY PADDLE LEVEL SWITCHES with 2 year warranty. Paddle switch catalogue HYC-PSC01
ROTARY PADDE EVE SITCES with year warranty Paddle switch catalogue YC-PSC01 YCONTRO ROTARY PADDE EVE SITC YEAR ARRANTY on the motor assembly due to unique design features:- motor shuts off when paddle
More informationROTARY PADDLE LEVEL SWITCHES
Paddle switch catalogue YC-PSC01 Iss. 03 ROTARY PADDLE LEVEL SWITCES LEVEL SWITCES FOR SOLIDS YCONTROL ROTARY PADDLE LEVEL SWITC YEAR WARRANTY on the motor assembly due to unique design features:- motor
More informationSérie. Détecteur à palette rotative. Rotary Padle Level Switch
Série SE Détecteur à palette rotative Rotary Padle Level Switch www.direct-mesure. INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery
More informationRotary Paddle Level Switch
www.fine-tek.com Rotary Paddle Level Switch INTRODUCTION WORKING PRINCIPLE The purpose of the rotary paddle level switch is to detect the presence of solid/powdery material in most kinds of tanks, bins
More informationCAPACITANCE LEVEL SWITCH
CAPACITANCE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 4 PRINCIPLE The capacitance level switch measuring principle is based on the "capacitance effects".
More informationTUNING FORK LEVEL WORKING PRINCIPLE APPLICATION. Solid Level Detection FEATURE. For Liquid: * Water & Solutions * General Purpose Solvent * Petroleum
TUNING FORK LEVEL WORKING PRINCIPLE The tuning fork of level switch operated by using two piezoelectric elements built-in on vibration tube. The first piezoelectric element triggered by pulse signal that
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationMAGNET FLOAT LEVEL TRANSMITTER
MAGNET FOAT EVE TANSMITTE http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown
More informationCAPACITIVE LEVEL SWITCHES. Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01
CAPACITIVE LEVEL SWITCHES Capacitive switch catalogue HYC-CSC01 Elect. Iss. 01 HYCONTROL CAPACITIVE LEVEL SWITCH RANGE Hycontrol ME capacitive level switches provide simple, accurate and reliable level
More informationTHERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH
THERMAL DISPERSION / PADDLE TYPE LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886-2-22696789 Fax: 886-2-22686682 OPERATING PRINCIPLE Thermal dispersion flow switch is a precise
More informationISO-9001:2000 certified Aplus Finetek Sensor, Inc.
SE3 Series Compact Rotary Paddle Point Level Sensor ISO-9001:2000 certified Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION PRINCIPLE The SE3 series is a compact rotary paddle point level sensor that uses
More informationFF Series Side Mount Float Level Switch
ISO-9001:000 certified FF Series Side Mount Float Level Switch More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION OPERATING PRINCIPLE The FF Series is a float
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationThermal Dispersion & Paddle Type Flow Switch.
Thermal Dispersion & Paddle Type Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationThermal Dispersion & Paddle Type Flow Switch. visit our website
Thermal Dispersion & Paddle Type Flow Switch visit our website PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationSP/SF Series Flow Switches
ISO-9001:2000 certified SP/SF Series Flow Switches More than just another level measurement company. Aplus Finetek Sensor, Inc. PRODUCT INTRODUCTION SP SERIES OPERATING PRINCIPLE SP SERIES The SP Series
More informationThermal Dispersion Flow Switch.
Thermal Dispersion Flow Switch www.fine-tek.com PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch s probe contains
More informationThermal Dispersion & Paddle Type Flow Switch
www.fine-tek.com Thermal Dispersion & Paddle Type Flow Switch PRODUCT INTRODUCTION OPERATING PRINCIPLE Thermal dispersion flow switches measure the velocity of a liquid inside a pipe or channel. The switch
More informationROTARY PADDLE TYPE LEVEL SWITCH
ROTRY PDDE TYPE EVE SWITCH N Series Rotary Type NM Series Rotary Type NN Series Reversible Type F-GM Series Rotary Type NNM Series Reversible Type Flame-proof dg Uncomparable models developed based on
More informationFINE AUTOMATION SIDE MOUNTING FLOAT SWITCH PRINCIPLE FEATURES WIRING
FINE AUTOMATION SIDE MOUNTING FLOAT SWITCH TEL: 886--6894607, 688605 FAX: 886--6894533, 6883318 http: //www.fineautomation.com e-mail: L93@ms15.hinet.net PRINCIPLE Simple theory as liquid buoyancy is utilized
More informationNIVOCONT R VIBRATING ROD LEVEL SWITCHES
For solids NIVOCONT R VIBRATING ROD LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES O U R P R O F E S S NIVOCONT R VIBRATING ROD LEVEL SWITCHES MAIN FEATURES Extension up
More informationINTRODUCTION FEATURES PRINCIPLE APPLICATIONS SCHEMATIC DIAGRAM OF THE PRINCIPLES CONSTRUCTION. 1. Sensing Rod 1 3 Ro Ri. 2. Float
INTOUCTION PINCIPE The "Magnet Float evel Transmitter" is composed of the float and sensing rod (shown as below). As the float raised or lowered by liquid level, the sensing rod will have a resistance
More informationMagnetic Float Level Indicator
Magnetic Float Level Indicator and By-Pass Level Indicator Magnetic Float Level Indicator The "Magnet Float Level Indicator" is composed of the float and sensing rod. As the float raised or lowered by
More informationMini Magnetic Float Type Level Switch
33 Mini Magnetic Float Type Level Switch Hydraulic Equipment. Lubricating Oils. and Coolant Tanks Introduction SFM series float type liquid level Switch made by Seojin Instech is intended for mounting
More informationfor free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES LEVEL SWITCHES
for free flowing solids NIVOROTA ROTARY PADDLE LEVEL SWITCHES O U R P R O F E S S I O N I S Y O U R L E V E L LEVEL SWITCHES MAIN FEATURES MAIN APPLICATION AREAS Level switching of free flowing solids
More informationCABLE FLOAT LEVEL SWITCH
CABLE FLOAT LEVEL SWITCH http: //www.fine-tek.com e-mail: info@fine-tek.com Tel: 886--696789 Fax: 886--68668 DESCRIPTI The Float Level Switch is made of chemical resistant polypropylene. It is durable,
More informationMAIN FUNCTION FEATURES. . D = v t /2
INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to meet the every-day needs of commercial production, as well serving a more specialized
More informationPRODUCTS GUIDE. Total solutions for monitoring liquid levels in the Marine Industry
PODUCTS GUIDE Total solutions for monitoring liquid levels in the Marine Industry visit our website FineTek Co., Ltd. No.16, Tzuchiang St., Tucheng Industrial Park, New Taipei City 36, Taiwan. TEL: 886
More informationMini-Roto TM Paddle Wheel Installation & Operation Manual
IOM LMR8000 Rev. F Mini-Roto TM Paddle Wheel Installation & Operation Manual Mini-Roto TM Paddle Wheel Installation & Operation Manual CONTENTS I. HANDLING & STORAGE... Inspection and Handling Disposal
More informationThe Mobrey product range provides reliable point level detection in a variety of dry solid applications
Product Data Sheet June 2015 IP400, Rev DG Mobrey Dry Products Level Measurement and Control The Mobrey product range provides reliable point level detection in a variety of dry solid applications The
More informationRotary Paddle Bin Monitor MODEL KA & KAX
Setting The Standard For Supplier Excellence Rotary Paddle Bin Monitor MODEL KA & KAX Hassle-Free Housing Design - No Bolts! Industry Leading Motor Shut-off Feature Economical, Versatile Point Level Bin
More informationPressure Level Transmitter.
Pressure Level Transmitter www.fine-tek.com C H 1 C H C H 1 C H PRODUCT INTRODUCTION FEATURES 1. FineTek Models include: extension cable transducer, Anti-corrosive model, flanged models & pressure transducers..
More informationMINI BY-PASS LEVEL INDICATOR
MINI BY-PASS LEVEL INDICATOR APPLICATIONS AND FEATURES It can be easily observed from the change of the flag color. Safer device comparing to glass type level gauge. Compact type, easy to install. Magnetic
More informationAP ATEX AIRPOWER POSITIONERS AP2000 FEATURES AP1000 & AP1200 FEATURES OPTIONS OPTIONS
AP1000-2000 Airpower positioners are a robust range of rotary or linear valve positioners in AP1000 electro-pneumatic (4-20mA), AP1200 pneumatic (3-15 psi) or AP2000 programmable smart type. Designed to
More informationMAIN FUNCTION FEATURES. . D = v t /2
ttp e-te com e-ma l o e-te com LT ASONIC LE EL MEAS EMENT Tel -2-22 Fa -2-22 2 INTRODUCTION The ultrasonic level Indicator is a low-cost, noncontact and easy-to-install measurement device. It is able to
More informationLevel Sensors and Switches Guided Radar (TDR) Radar Wave Level Sensors Ultrasonic Level Sensors Rotating Paddle Level Switches Vibrating Fork Level
Level and Switches Level Level Applications Suitable for the applications in the field of chemical plastics, pharmaceutical manufacturing, fodder, grains, cement, fertilizer, powder, fuel materials, hydraulic
More informationValve Position Monitors
CONTROLS Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X CONTROLS Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationROTARY Point Level Measurement for Inventory Control
Measure. Detect. Alert. ROTARY Point Level Measurement for Inventory Control Detect high and low levels while protecting valuable inventory with tried-and-true rotary level indicators from BinMaster. Made
More informationCVR-625. Compact Vibrating Rod Instruction Manual
CVR-625 Compact Vibrating Rod Instruction Manual BinMaster: Division of Garner Industries 7201 N. 98th St., Lincoln, NE 68507 402-434-9102 email: info@binmaster.com www.binmaster.com OPERATING INSTRUCTIONS
More informationPressure Controller. Cataloge K Code Characteristics Index. K00-2 Pressure Controller Brief Introduction
K Pressure Controller Cataloge Code Characteristics Index K00-2 Pressure Controller Brief Introduction KC32 Screw Tube Differential Pressure Controller K01 KY10 Bellows Type Differential Pressure Controller
More informationModel R7 Rotating Paddle Level Sensor Ideal for powders, solids, and granular material
NOHKEN INC Rotating Paddle Level Sensor Model R7 Rotating Paddle Level Sensor Ideal for powders, solids, and granular material Product Overview R7 is a solid level measurement sensor that is ideal to incorporate
More informationV200 Series Positioners
V200 Series Positioners In a single compact and rugged housing The V200 positioner incorporates the flexibility of converting from a pneumatic unit to several versions of an electropneumatic unit, and
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS200 Standard. icenta Controls Ltd
Pointek CLS200 Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level switch with optional rod/cable choices liquids, solids,
More informationMetal tube variable area flowmeter for gases, liquids and steam
Metal tube variable area flowmeter for gases, liquids and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h, kg/h, t/h,
More informationVRF II Series SURPASSING SENSITIVITY FOR THE TOUGHEST APPLICATIONS FEATURES AND BENEFITS STANDARD VS. ADVANCED UNITS
VRF II Series SURPASSING SENSITIVITY FOR THE TOUGHEST APPLICATIONS The VRF II Series uses radio frequency to detect the presence or absence of material in a vessel. It compensates for the load of the probe
More informationDifferential Pressure Gauges Cryo Gauge Model , Cu-alloy Model , Stainless Steel Series
Differential Pressure Gauges Cryo Gauge Model 712.15.160, Cu-alloy Model 732.15.160, Stainless Steel Series Mechanical Pressure Measurement WIKA Data Sheet PM 07.30 Applications Level measurement in closed
More informationMetal tube flowmeters. Series SC250. Metal Tube Flow Meters. Series SC250. Variable area flowmeter for liquids, gases and steam
Metal tube flowmeters Variable area flowmeter for liquids, gases and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h,
More informationTuffy Liquid Level Switches
Tuffy Liquid Level es Tuffy liquid level switches are designed for horizontal mounting in a tank or vessel through threaded or flanged pipe connections. Models are equipped with a single electric or pneumatic
More informationSS3 Linear / Rotary. Smart Valve Positioner. Smart performance with innovative and ever-strong coil drive even under harsh working environments
Smart Valve Positioner SS3 Linear / Rotary Smart performance with innovative and ever-strong coil drive even under harsh working environments Easy and quick auto-calibration Detecting RA (reverse acting)
More informationD2SW. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
ealed ubminiature Basic witch ealed ubminiature Basic witch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject
More informationAM9000 Series GENERAL FEATURES METAL TUBE VARIABLE AREA FLOWMETER
METAL TUBE VARIABLE AREA FLOWMETER AM9000 Series GENERAL The AM9000 series metal tube variable area flowmeters have the unified face-to-face dimension mm. Having developed the current well-accepted AM7000
More informationPNEUMATIC ACTUATORS. Linear acting
PNEUMATIC ACTUATORS We supply pneumatic double-acting or single-acting with spring return. The actuators are mainly quarterturn actuators for butterflyvalves and ball valves or multiturn for gate valves
More informationElectric Actuated Butterfly Valves Ductile Iron Wafer Body ASME 150# 2 to 6 Pipe
2 to 6 Pipe Features Direct mount wafer butterfly valve with ISO5211 mount 3-layer epoxy coated ductile iron body with 316 SS disc Unique wave line seat reduces torque and extends seal life Visual valve
More informationLevel switches Series LC40 Float level switch for liquids
Level switches Series LC40 Float level switch for liquids Simple and robust construction Versatile and easily adaptable to the different control positions of the industrial processes Side or top of the
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS200 Standard. 4/18 Siemens FI Overview.
Pointek CLS200 Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level switch with optional rod/cable choices liquids, solids,
More informationD2SW. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
ealed ubminiature Basic witch ealed ubminiature Basic witch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject
More informationD2SW-AQ. Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal models) Model Number Legend
Sealed Subminiature Basic Switch Conforming to IP67 (Excluding the terminals on terminal ) Use of epoxy resin assures stable sealing, making this switch ideal for places subject to water spray or excessive
More informationMobrey dry products level measurement and control
Product Data Sheet Mobrey offer a range of technologies for reliable point-level detection in a variety of dry solid applications The Mobrey Series PLS is a paddle rotating level switch that detects high
More informationSeries 60. New Smart Positioner. Compact design Convenient & powerful function Enhanced reliability
Series 60 New Smart Positioner Compact design Convenient & powerful function Enhanced reliability J Flow Controls, LLC 14 De Camp Cincinnati, OH 45216 Phone: 513-731-2900 Fax 513-731-6939 www.jflowcontrols.com
More informationElectro-Pneumatic Positioner YT-1000 / 1050 SERIES
Electro-Pneumatic Positioner YT-1000 / 1050 SERIES PRODUCT MANUAL VERSION 1.01 Contents 1. Introduction 4 1.1 General information for the users. 4 1.2 Manufacturer Warranty 4 1.3 Explosion Proof Warning.
More informationGlass tube flowmeters Series 6000 Variable area flowmeter for liquids and gases
Glass tube flowmeters Series 6000 Variable area flowmeter for liquids and gases Easy installation Local indication by means of direct reading Low pressure drop Scales directly in l/h, m 3 /h, kg/h, l/min,
More informationSuper-Safe-Plus Roto-Bin-Dicator
Super-Safe-Plus Roto-Bin-Dicator for your most demanding applications... Offers both mechanical and electronic sensing in one reliable Point Level Sensor... Level control with added confidence Under normal
More informationRPPN3 - RPPN7 Industrial pressure switch
Main Features Excellent repeatability Dead band adjustment for regulation Fix dead band for control and alarm Applications Energy safety equipment Power generation safety equipment Pressurized chambers
More informationSolid / Liquid Level Measurement for Field Application Pneumatic Vibrator/Air Shocker Solution Temperature Controller/ Counter /Digital Panel Meter
Solid / Liquid Level Measurement for Field Application Pneumatic Vibrator/Air Shocker Solution Temperature Controller/ Counter /Digital Panel Meter By-pass Level Transmitter EF Series Material SUS316,
More informationLevel Devices. Rotary Level Indicators Roto-Bin-Dicator
7901 NW 107th Terrace Level Devices We offer Rotary Level Indicators, Radio Frequency Level Indicators, and Turning Fork Level Sensors. For more information please contact your Schenck Process Aftermarket
More informationLevel Switch MPC2000 MPC2
Technical Information Level Switch MPC2000 MPC2 Displacement Type Level Switch Application MPC series level controllers are displacement type instruments for tank installation. MPC provides 1to 4 control
More informationFeatures. Flexibility
The V100 positioner can be ordered as a base model pneumatic positioner, converted to standard NEMA 4X electropneumatic, EX model, or FF (fail freeze) model in a matter of minutes, without removing the
More informationHeavy-Duty Pneumatic Actuator. IS & IC Series
Heavy-Duty Pneumatic Actuator BS EN ISO 9001:2000 INTRODUCTION Heavy-Duty Pneumatic Actuator - The IS & IC series of Heavy Duty scotch yoke actuators are designed to suit a wide range of valves and damper
More informationElectric Actuated Ball Valves 3-piece Stainless Steel, Full Port 1/4 to 3 NPT
1/4 to 3 NPT Features Direct mount ISO5211 Full Port stainless steel ball valve 3-piece swing out body designed for easy maintenance 1000 PSI working pressure at 100 F (38 C) Highly visual dome style valve
More informationPressure Switch. visit our website
Pressure Switch visit our website SPST TYPE CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. TYPE Hex length Body material rating
More informationElectric Actuated Ball Valves 150# Flanged Stainless Steel, Full Port 1/2 to 4 inch Pipe
1/2 to 4 inch Pipe Features Direct mount ISO5211 Full Port stainless steel ball valve 2-piece ANSI Class 150 flanged body 275 PSI working pressure at 100 F (38 C) Highly visual dome style valve position
More informationPressure Switch. visit our website
Pressure Switch visit our website SPST TYPE CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. CE (need to add anti-dust cover SQA-1130. TYPE Hex Length Body rating (Max.)
More informationSoliswitch FTE30. Technical Information
Technical Information Soliswitch FTE30 Level limit switch Economical paddle limit switch with type-examination certificate to ATEX dust Ex-approval zone 20 Application The universal paddle level limit
More informationPull Cord Switch BX5800. Application
Pull Cord Switch BX5800 Application The Pull Cord Switch is an emergency switch used to stop the belt conveyor instantly when an accident occurs. When an accident occurs or for the normal corrective maintenance,
More informationRPPN6 - RPPN8 Industrial pressure switch with high overpressure resistance
Main Features Excellent repeatability Dead band adjustment for regulation Fix dead band for control and alarm Overpressure up to 100 bar Applications Energy safety equipment Power generation safety equipment
More informationValve Position Monitors
Valve Position Monitors EX Series for Hazardous Locations APL Series NEMA 4, 4X 1 LIMIT SWITCHES Triac APL Series Limit Switches The Triac APL Series Limit Switches feature high quality, easy to use multiple
More informationprocess measurement solutions The dry products level control catalogue
process measurement solutions The dry products level control catalogue 1 Dry products level measurement and control from Solartron Mobrey The measurement and control of dry products is important in all
More informationPRODUCTS CATALOG (2018) TISSIN CO.,LTD. Smart Valve Positioner. Electro-Pneumatic Positioner. Volume Booster. Lock Up Valve. Air Filter Regulator
PRODUCTS CATAOG (08) TISSIN CO.,TD. Smart Valve Positioner Electro-Pneumatic Positioner Volume Booster ock Up Valve Air Filter Regulator Solutions for control valve system About Tissin Solutions for control
More informationLNT SPECIFICATION SHEET 3.4W PER FT. CRI 3.4W IP68 NEON SERIES LED STRIP 50,000 HOURS FEATURES SPECIFICATIONS
NT-65 3.4 IP68 NEON SERIES ED STRIP JOB NAME: OCATION: QUOTE/REF#: SPECIFICATION SEET NT65 is a high performance flexible ED fixture designed as a neon replacement. Suitable for indoor and outdoor applications,
More informationDIAMOND POINT VIBRATING PROBES
DIAMOND POINT VIBRATING PROBES DP130 DP120 DP140 DP150 Instruction Manual Third revision, April 2016 Hycontrol Ltd., Larchwood House, Orchard Street, Redditch, Worcestershire, B98 7DP, U.K. Tel: + 44 (0)1527
More informationPOSITIONERS and Controls for Complete Valve Automation
CONTROLS A Division of AT Controls Pneumatic & Electro-Pneumatic POSITIONERS and Controls for Complete Valve Automation 1 SS SERIES SS Features Easy and quick auto-calibration Detecting RA (reverse acting)
More informationRead and understand this manual for safely usage.
TS02-0200 INSTRUCTION MANUAL FOR VIBRATING LEVEL SENSOR MODEL:VH Read and understand this manual for safely usage. This manual describes the product of standard specification. Read the other manual for
More informationPLUGS & RECEPTACLES. INNOVATIVE EXPLOSION PROTECTION by R. STAHL
Series Features: Color coding and pin configuration makes it physically impossible to mate plugs and receptacles of different voltages and current ratings (per IEC 60 309-2). Interlocked switch mechanism
More informationOPTIGAS 4010C Technical Datasheet
OPTIGAS 4010C Technical Datasheet Sensor for gas dispenser applications Compact design for easy istallation High accuracy with wide measuring range Designed to fit existing dispensers The documentation
More informationPoint level measurement Capacitance switches
Pointek CLS300 Standard Overview Configuration Installation Pointek CLS300 (standard version) is an inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output.
More informationElectric Actuated 3-Way Ball Valves T-Port Diverter, Stainless Steel, Full Port 1/4 to 2 NPT
T-Port Diverter, Stainless Steel, Full Port 1/4 to 2 NPT Features Full Port direct mount 316 SS ball valve Functions as a diverter valve 1000 PSI working pressure at 100 F (38 C) Visual valve position
More informationEX Series. Electric Actuators for Ball and Butterfly Valves
EX Series Electric Actuators for Ball and Butterfly Valves Next Generation Electrical Actuator Realization of Upgraded General-Purpose Actuators The modularization and the adoption of common parts have
More informationD2VW. Sealed Miniature Basic Switch Conforms to IP67 (Excluding the terminals on terminal models) Model Number Legend. Sealed Miniature Basic Switch
Sealed Miniature Basic Switch Conforms to IP67 (Excluding the terminals on terminal models) Use of epoxy resin assures stable sealing, making this switch ideal for places subject to water spray or excessive
More informationLevel Measurement Point level measurement - RF Capacitance switches
Pointek CLS200 - Standard Overview Configuration Installation Pointek CLS200 (standard version) is a versatile inverse frequency shift capacitance level and material detection switch with optional rod/cable
More informationOPTIGAS 4010C Technical Datasheet
OPTIGAS 4010C Technical Datasheet Sensor for gas dispenser applications Compact design for easy istallation High accuracy with wide measuring range Designed to fit existing dispensers The documentation
More informationIt s time to get connected with
It s time to get connected with The essence of quality NEW See pag e6 PRATLEY products and P NUTS are distributed exclusively in the UK by: Cable Connectors Ltd Product Brochure Aluminium Alloy (Corrosion
More informationRHM40. Coriolis Mass Flow Meter for Demanding Applications. Features. Applications. Benefits
RHM40 Coriolis Mass Flow Meter for Demanding Applications Features Standard pressure ratings up to 433 bar (6280 psi) Temperature ratings from -196 to 350 C (-320 to 662 F) Mass flow uncertainty down to
More informationBMRX Series ROTARY LEVEL CONTROL
BMRX Series ROTARY LEVEL CONTROL OPERATING INSTRUCTIONS PLEASE READ CAREFULLY 925-0292 Rev C TABLE OF CONTENTS GENERAL SPECIFICATIONS... 3 SAFETY SUMMARY... 4 1.0 INTRODUCTION... 5 2.0 INSTALLATION...
More information