VALVE BODY ASSEMBLY ON VEHICLE REPAIR

Size: px

Start display at page:

Download "VALVE BODY ASSEMBLY ON VEHICLE REPAIR"

Warren Barnaby Gallagher
6 years ago
Views:

1 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY VLVE ODY SSEMLY ONVEHICLE REPIR X7 X03Q02 1. DRIN TF Using a hexagon wrench, remove the drain plug and fluid into the suitable container. 2. REMOVE OIL PN ND GSKET Some fluid will remain in the oil pan. Remove oil pan bolts, and carefully remove the pan assembly. Discard the gasket. T EXMINE PRTICLES IN PN Remove the magnets and use them to collect any steel chips. Look at the chips and particles in the pan and magnet carefully to anticipate what type of wear you will find in the transaxle. Steel (magnetic): bearing, gear and plate wear rass (nonmagnetic): bushing wear T REMOVE OIL STRINER ND PPLY PIPE RCKET (a) Remove the 3 bolts and oil strainer. e careful as oil will come out of the strainer when it is removed. (b) Remove the 3 bolts and apply pipe bracket. D01019 Connector 5. REMOVE OIL PIPES Pry up both pipe ends with a large screwdriver and remove the 5 pipes. 6. DISCONNECT SOLENOID CONNECTORS Q05728 uthor : 1874

2 X8 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY 7. REMOVE DETENT SPRING ND OIL PIPE (a) Remove the 2 bolts and detent spring. (b) Remove the bolt. (c) Pry up the pipe with a screwdriver and remove the pipe. D REMOVE MNUL VLVE ODY Remove the 5 bolts and manual valve body. D REMOVE CONNECTOR CLMP ND PIPE RETINER Remove the 2 bolts, connector clamp and pipe retainer. D REMOVE 3 PPLY PIPE Pry up the pipe with a screwdriver and remove the pipe. D REMOVE VLVE ODY (a) Remove the 9 bolts. D01023 uthor : 1875

3 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY X9 (b) Disconnect the throttle cable from the cam and remove the valve body. 12. REMOVE 2ND RKE PPLY GSKET OR REMOVE SOLENOID VLVES (a) Remove the 3 bolts, shift solenoid valve No.1 and No.2 with the retainer. When removing solenoid, do not use a screwdriver, etc. to pry up the solenoid. (b) Remove the Orings from the shift solenoid valve No.1 and No.2. Q05643 (c) (d) Remove the bolt and shift solenoid valve SL. Remove the Oring from the shift solenoid valve SL. Q05657 (e) (f) Remove the bolt and shift solenoid valve SLN. Remove the Oring from the shift solenoid valve SLN. Q INSTLL SOLENOID VLVES (a) Coat the 2 new Orings with TF and install it to the shift solenoid valve SL. (b) Install the shift solenoid valve SL. (c) Install and torque the bolt. Torque: 6.6 N m (67 kgf cm, 58 in. lbf) Q05657 uthor : 1876

4 X10 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY (d) (e) (f) Coat the 2 new Orings with TF and install it to the shift solenoid valve SLN. Install the shift solenoid valve SLN. Install and torque the bolt. Torque: 6.6 N m (67 kgf cm, 58 in. lbf) Q05402 (g) Coat the 2 new Orings with TF and install it to the shift solenoid valve No.1 and No.2. (h) Install the No.1 and No.2 solenoids. (i) Install and torque the 3 bolts. Torque: 6.6 N m (67 kgf cm, 58 in. lbf) 15. PLCE NEW 2ND RKE PPLY GSKET Q INSTLL VLVE ODY TO TRNSXLE CSE (a) While holding the cam down with your hand, slip the cable end into the slot. (b) Lower the valve body into place. e careful not to entangle the solenoid wire. OR0038 C D C D C D01023 (c) Install and tighten the 9 bolts. HINT: Hand tighten the 9 bolts first, then torque with a torque wrench. olt length: olt : 30 mm (1.181 in.) olt : 43 mm (1.693 in.) olt C: 48 mm (1.890 in.) olt D: 52 mm (2.047 in.) 17. INSTLL 3 PPLY PIPE e careful not to bend or damage the pipe. D01058 uthor : 1877

5 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY X INSTLL CONNECTOR CLMP ND PIPE RETINER (a) Install the connector clamp and pipe retainer. (b) Install and torque the 2 bolts. olt length: olt : 48 mm (1.890 in.) olt : 39 mm (1.535 in.) D (1.18) D01021 mm (in.) Z INSTLL MNUL VLVE ODY (a) lign the manual valve with the pin on the manual shaft lever. (b) Lower the manual valve body into place. (c) Hand tighten the 5 bolts first. Then, tighten them with a torque wrench. olt length: olt : 22 mm (0.866 in.) olt : 37 mm (1.457 in.) 20. INSTLL DETENT SPRING ND OIL PIPE (a) Place the detent springs on the manual valve body and hand tighten the 2 bolts first. Then, tighten them with a torque wrench. olt length: olt : 14 mm (0.551 in.) olt : 37 mm (1.457 in.) (b) Check that the manual valve lever is touching the center of the detent spring tip roller. (c) Using a plastic hammer, install the pipe into the position. e careful not to bend or damage the pipe. (d) Install and torque the bolt. Torque: 10 N m (100 kgf cm, 7 ft lbf) Connector 21. CONNECT SOLENOID CONNECTORS 22. INSTLL OIL PIPES Using a plastic hammer, install the pipes into the positions. e careful not to bend or damage the pipes. Q05728 uthor : 1878

6 X12 UTOMTIC TRNSXLE (541E) VLVE ODY SSEMLY Z INSTLL OIL STRINER ND PPLY PIPE RCKET (a) Install the oil strainer and apply pipe bracket. (b) Install and torque the 6 bolts. olt length: olt : 22 mm (0.866 in.) olt : 53 mm (2.087 in.) Torque: olt : 10 N m (100 kgf cm, 7 ft lbf) olt : 11 N m (110 kgf cm, 8 ft lbf) 24. INSTLL MGNETS IN PLCE Install the 3 magnets in the indentations of the oil pan, as shown in the illustration. Make sure that the magnet does not interfere with the oil pipes. T INSTLL OIL PN ND GSKET (a) Install the oil pan and a new gasket. (b) Install and torque the 17 new bolts. Torque: 7.8 N m (80 kgf cm, 69 in. lbf) 26. INSTLL ND TORQUE DRIN PLUG Torque: 49 N m (500 kgf cm, 36 ft lbf) 27. FILL TF ND CHECK FLUID LEVEL (See page DI416) T3785 uthor : 1879

VALVE BODY ASSEMBLY ON VEHICLE REPAIR

VALVE BODY ASSEMBLY ON VEHICLE REPAIR T10 UTOMTI TRNSMISSION (340E, 340F) VLVE ODY SSEMLY VLVE ODY SSEMLY ONVEHILE REPIR UTION: T12U01 When working with FIPG material, you must observe the followings. Using a razor blade and a gasket scraper,