FUEL PUMP SYSTEM CIRCUIT
|
|
|
- Earl Leon Harrington
- 5 years ago
- Views:
Transcription
1 EG RE ENGINE FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Turn the ignition switch ON. HINT: Do not start the engine. (b) Using SST, connect terminals Fp and +B of the DLC1. SST HINT: The DLC1 is located near the No. 2 relay block. (c) Check that there is pressure in the fuel inlet hose. HINT: At this time, you will hear fuel return noise from the pressure regulator. (d) Remove SST from the DLC1. (e) Turn the ignition switch OFF. If there is no pressure, check the following parts: Fusible links Fuses (EFI 15A, IGN 7.5A) EFI main relay
2 22RE ENGINE EG1183 Circuit opening relay Fuel pump Wiring connections 2. CHECK FUEL PRESSURE (a) Check that the battery voltage is above 12 volts. (b) Disconnect negative () terminal cable from of the battery. (c) Disconnect the wiring connector from the cold start injector. (d) Put a suitable container or shop towel under the cold start injector pipe. (e) Slowly loosen the union bolts of the cold start injector pipe and remove the bolts, cold start injector pipe and 4 gaskets. (f) Drain the fuel from the delivery pipe. (g) Install a gasket, SST, another gasket and union bolt to the delivery pipe as shown in the illustration. SST (h) Wipe off any splattered gasoline. (i) (j) Reconnent the negative () terminal cable to the battery. Using SST, connect terminals Fp and +B of the DLC1. SST
3 EG RE ENGINE (k) Turn the ignition switch ON. (l) Measure the fuel pressure. Fuel pressure: kpa ( kgf/cm 2, 3844 psi) If high, replace the pressure regulator. If low, check the following parts: Fuel hoses and connections Fuel pump Fuel filter Pressure regulator (m) Remove SST from the DLC1. (n) Start the engine. (o) Disconnect the vacuum hose from the pressure regulator and plug it closed. (p) Measure the fuel pressure at idling. Fuel pressure: kpa ( kgf/cm 2, 3844 psi) (q) Reconnect the vacuum hose to the pressure regulator. (r) Measure the fuel pressure at idling. Fuel pressure: kpa ( kgf/cm 2, 3337 psi) If not within the specified pressure, check the vacuum hose and pressure regulator. (s) Stop the engine. Check that the fuel pressure remains above 147 kpa (1.5 kgf/cm 2, 21 psi) for 5 minutes after the engine is turned off. If not within the specification, check the fuel pump, pressure regulator and/or injectors. (t) After checking fuel pressure, disconnect the battery ground strap and carefully remove the SST to prevent gasoline from splashing. (u) Using new gaskets, reconnect the cold start injector pipe to the delivery pipe and cold start injector. (v) Connect the wiring connector to the cold start injector. (w) Start the engine and check for fuel leakage.
4 22RE ENGINE COMPONENTS FOR REMOVAL AND INSTALLATION EG1185 FUEL PUMP REMOVAL 1. DRAIN FUEL FROM FUEL TANK CAUTION: Do not smoke or work near an open flame when working on the fuel pump. 2. REMOVE FUEL TANK 3. REMOVE FUEL PUMP BRACKET (a) Remove the 7 bolts. (b) Pull out the fuel pump bracket.
5 EG RE ENGINE 4. REMOVE FUEL PUMP FROM FUEL PUMP BRACKET (a) Pull off the lower side of the fuel pump from the pump bracket. (b) Disconnect the fuel pump connector. (c) Disconnect the fuel hose from the fuel pump, and remove the fuel pump. (d) Remove the rubber cushion from the fuel pump. 5. REMOVE FUEL PUMP FILTER FROM FUEL PUMP (a) Using a small screwdriver, remove the clip. (b) Pull out the pump filter. FUEL PUMP INSTALLATION (See Components for Removal and Installation) 1. INSTALL FUEL PUMP FILTER TO FUEL PUMP Install the pump filter with a new clip. 2. INSTALL FUEL PUMP TO FUEL PUMP BRACKET (a) Install the rubber cushion to the fuel pump. (b) Connect the fuel hose to the outlet port of the fuel pump. (c) Install the fuel pump connector. (d) Install the fuel pump by pushing the lower side of the fuel pump. 3. INSTALL FUEL PUMP BRACKET (a) Place the bracket with a new gasket on the fuel tank. (b) Install and tighten the 7 bolts. Torque: 3.9 N m (40 kgf cm, 34 in. lbf)
6 22RE ENGINE EG INSTALL FUEL TANK NOTICE: Tighten the pipe and flare nut type hose to the specified torque. Push in the pipe and inserttype hose to the specified position, and install the clip to the specified location. If reusing the hose, reinstall the clip at the original location. 5. REFILL WITH FUEL
FUEL PUMP SYSTEM CIRCUIT
EG190 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the DLC1. SST 0984318020 (b) Turn the ignition switch ON. NOTICE: Do not start
FUEL PUMP SYSTEM CIRCUIT
EG199 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SSt, connect terminals +B and FP of the data link connector 1. SST 0984318020 (b) Turn the ignition switch ON.
FI 135. Fuel Pump (3S GTE)
Fuel System (Fuel Pump (3SGTE)) FI135 Fuel Pump (3SGTE) FI136 MFI AND SFI SYSTEMS Fuel System (Fuel Pump (3SGTE)) ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and
FUEL PUMP. ON VEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the data link connector 1.
EG2250 FUEL PUMP ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the data link connector 1. SST 0984318020 (b) Turn the ignition switch ON. NOTICE: Do not
FUEL PRESSURE REGULATOR
EG2214 3VZE ENGINE FUEL PRESSURE REGULATOR ONVEHICLE INSPECTION CHECK FUEL PRESSURE (See step 2 on page EG2206) COMPONENTS FOR REMOVAL AND INSTALLATION FUEL PRESSURE REGULATOR REMOVAL 1. DISCONNECT NEGATIVE
1996 Toyota Camry DX ENGINE PERFORMANCE Toyota Basic Diagnostic Procedures
FUEL SYSTEM Basic diagnosis of fuel system should begin by checking fuel pump operation and fuel pressure. WARNING: ALWAYS release fuel pressure before disconnecting any fuel injection-related component.
Cylinder Head Setting Bolt Tightening Adaptor Injection Measuring Tool Set EFI Fuel Pressure Gauge
SFI SYSTEM (2JZGE) EG187 SFI SYSTEM (2JZGE) PREPARATION SST (SPECIAL SERVICE TOOLS) 0920576030 Cylinder Head Setting Bolt Tightening Adaptor ECT sensor 0926841045 Injection Measuring Tool Set (0926841070)
FUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
INJECTOR ON VEHICLE INSPECTION 1. CHECK INJECTOR OPERATION
EG1187 INJECTOR ONVEHICLE INSPECTION 1. CHECK INJECTOR OPERATION Check for operating sound from each injector. (a) With the engine running or cranking, use a sound scope to check that there is normal operating
Injectors (4A FE) FI 155. (b) If you have no sound scope, you can check the injector transmission operation with your finger.
FI155 Injectors (4AFE) ONVEHICLE INSPECTION 1. INSPECT INJECTOR OPERATION Check operation sound from each injector. (a) With the engine running or cranking, use a sound scope to check that there. is normal
MAINTENANCE PRECAUTIONS CHECK CORRECT ENGINE TUNE UP 2. PRECAUTION WHEN CONNECTING GAUGE
EG1105 PRECAUTIONS 1. Before working on the system, disconnect the neg ative terminal from the battery. HINT: Any diagnostic trouble code retained by the computer will be erased when the battery terminal
INJECTOR COMPONENTS SF-18. Air Cleaner Hose. Accelerator Cable Water Bypass Hose Air Hose. PCV Hose. Throttle Position Sensor Connector.
SF18 SFI (5VZFE) COMPONENTS SF02204 Air Cleaner Hose PCV Hose Accelerator Cable Water Bypass Hose Air Hose Throttle Position Sensor Connector CCV Hose Accelerator Pedal Position Sensor Connector Throttle
IGNITION SYSTEM ON-VEHICLE INSPECTION NOTICE:
ONVEHICLE INSPECTION SPARK TEST NO CHECK CONNECTION OF COIL CONNECTOR CHANGE IT TO NORMAL COIL (WITH IGNITER) AND PERFORM SPARK TEST AGAIN NO CHECK POWER SUPPLY TO COIL (WITH IGNITER) 1. Turn ignition
ON VEHICLE INSPECTION NOTICE:
ONVEHICLE INSPECTION IGNITION (2JZGE) and in these sentences express the temperature of the coils and sensors themselves. is from1 0 C (14 F) to 50 C (122 F) and is from C 50 (122 F) to100 C (212 F). 1.
SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.
EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
F - BASIC TESTING Toyota Celica INTRODUCTION PRELIMINARY INSPECTION & ADJUSTMENTS VISUAL INSPECTION MECHANICAL INSPECTION
F - BASIC TESTING 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 4-Cylinder Basic Diagnostic Procedures Celica INTRODUCTION The following diagnostic steps will help prevent overlooking a simple problem.
EFI SYSTEM PRECAUTION
ELECTRONIC FUEL INJECTION (2JZGE) PRECAUTION FI1 SF0N107 1. BEFORE WORKING ON FUEL SYSTEM, DISCON- NECT NEGATIVE () TERMINAL CABLE FROM BAT- TERY Any diagnostic trouble code retained by the engine ECU
2001 Audi TT Quattro ENGINE PERFORMANCE' 'System & Component Testing
FUEL SYSTEM WARNING: ALWAYS release fuel pressure before disconnecting fuel injection-related component. DO NOT allow fuel to contact engine or electrical components. FUEL INJECTOR TEST Fuel Injector Electrical
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN (LSC) A0N HV WATER PUMP REPLACEMENT MODEL YEAR PRIUS
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN (LSC) A0N HV WATER PUMP REPLACEMENT 2004 2007 MODEL YEAR PRIUS I. OPERATION FLOWCHART II. IDENTIFICATION OF AFFECTED VEHICLES A. AFFECTED VIN RANGE Model
AUTOMATIC TRANSMISSION FLUID (A750E/A750F)
404 AUTOMATIC TRANSMISSION / TRANS ADJUSTMENT 4017G02 1. BEFORE FILLING TRANSMISSION This transmission requires Toyota Genuine ATF WS. It is necessary to refill the transmission with the correct amount
PRECAUTION. MAINTENANCE PRECAUTIONS 1. CHECK CORRECT ENGINE TUNE UP (See Tune Up under Engine Mechanical) EG2 197
EG2197 PRECAUTION 1. Before working on the fuel system, disconnect the cable from negative () terminal of the battery. HINT: Any diagnostic trouble code retained by the computer will be erased when the
COMPONENTS SF-52 ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) Suction Hose. Throttle Body Cover. MAF Meter Wire. Vacuum Hose. PS Air Hose.
SF52 SFI (2UZFE) ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) COMPONENTS SF1XM01 Suction Hose MAF Meter Wire Throttle Body Cover PS Air Hose Vacuum Hose PCV Hose Intake Air Connector B17459 3637 SFI (2UZFE)
OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.
OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)
ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination
Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity
ENGINE EG329 PREPARATION SST (SPECIAL SERVICE TOOLS) 0923001010 Radiator Service Tool Set 0923114010 Punch 2JZGE only (Aluminum type) RECOMMENDED TOOLS 0904000010 Hexagon Wrench Set 0908200050 TOYOTA Electrical
IGNITION SYSTEM ON-VEHICLE INSPECTION
ONVEHICLE INSPECTION IGNITION (5VZFE) and in these sentences express the temperature of the coils themselves. is from 10 C (14 F) to 50 C (122 F) and is from 50 C (122 F) to 100 C (212 F). 1. INSPECT IGNITOR
ACC CUT RELAY INSPECTION
ACC Cut Relay ACC CUT RELAY ACC CUT RELAY INSPECTION 1. REMOVE ACC CUT RELAY Remove the relay box and ACC cut relay. ST19 ST0OU01 B16462 Continuity 4 2 1 5 3 Continuity No continuity S04972 2. INSPECT
THROTTLE BODY ON VEHICLE INSPECTION EG INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly.
EG2234 THROTTLE BODY ONVEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port. Start the engine. Check the vacuum with your finger.
REMOVE FRONT WHEEL RH
518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER
EG2 173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM
5SFE ENGINE EG2173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM EG2174 5SFE ENGINE EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter
LUBRICATION SYSTEM (April, 2003)
SYSTEM (April, 2003) SYSTEM (April, 2003) ONVEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the L and
TURBOCHARGER ON VEHICLE INSPECTION TC 7
TC7 ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR SYSTEM Check for leakage or clogging between the air cleaner and turbocharger inlet and between the turbocharger outlet and cylinder head. Clogged air cleaner...
IGNITION SYSTEM ON VEHICLE INSPECTION NOTICE:
SYSTEM ONVEHICLE INSPECTION NOTICE: SPARK TEST NO CHECK CONNECTION OF COIL, IGNITER AND DISTRIBUTOR CONNECTOR OK CHECK RESISTANCE OF HIGHTENSION CORD (See step 2) Maximum resistance: 25 kω per cord OK
RADIATOR CLEANING OF RADIATOR
CO20 COOLING SYSTEM RADIATOR CLEANING OF RADIATOR Using water or a steam cleaner, remove any mud and dirt from the radiator core. CAUTION: If using a high pressure type cleaner, be careful not to deform
OPERATION AT-2. Clutch No.3 (C 3 ) Clutch No.1 (C 1 ) One-way Clutch
AT2 OPERATION AT13K01 Clutch No.3 (C 3 ) Clutch No.1 (C 1 ) Clutch No.2 (C 2 ) Oneway Clutch No.2 (F 2 ) Brake No.3 (B 3 ) Oneway Clutch No.1 (F 1 ) Brake No.1 (B 1 ) Brake No.2 (B 2 ) Oneway Clutch No.3
ACC CUT RELAY INSPECTION
STARTING (2UZFE) ACC CUT RELAY ACC CUT RELAY INSPECTION 1. REMOVE ACC CUT RELAY Remove the cowl side trim board LH and ACC cut relay. ST21 ST0Q102 Continuity 4 2 1 5 3 No continuity Continuity S04972 2.
COOLING SYSTEM ON-VEHICLE INSPECTION CO 1
Radiator Cap Tester 2AZ-FE OLING OLING SYSTEM A112194E01 A112306 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK OLING SYSTEM FOR LEAKS (a) Remove the radiator reservoir cap. CAUTION: To avoid the danger
TROUBLESHOOTING PROBLEM SYMPTOMS TABLE
TURBOCHARGING (2JZGTE) TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Before troubleshooting the turbocharger, first check the engine itself. (Valve clearance, engine compression, ignition timing
CAMSHAFT POSITION SENSOR
IG8 IGNITION CAMSHAFT POSITION SENSOR COMPONENTS CAMSHAFT POSITION SENSOR IG08T03 Fuel Return Hose VBank Cover 7.5 (80, 66 in. lbf) Camshaft Position Sensor Camshaft Position Sensor Connector Grommet 7.5
25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.
CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE
EXHAUST GAS RECIRCULATION (EGR) SYSTEM
ENGINE EG169 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (California only) EG170 ENGINE To reduce NOx emissions, part of the exhaust gases are recirculated through the EGR valve to the intake manifold to lower
EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE
ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY
Mazda Reference MA014
Subject: Fuel system pressure testing for fuel injected engines Symptom: Hard starting cold, power loss climbing hills, overall poor performance, engine surges and then stops running Source: Mazda service
IGNITION SYSTEM ON-VEHICLE INSPECTION
IGNITION (5VZFE) ONVEHICLE INSPECTION IG1 IG00U07 and in these sentences express the temperature of the coils themselves. is from 10 C (14 F) to 50 C (122 F) and is from 50 C (122 F) to 100 C (212 F).
IGNITION SYSTEM ON-VEHICLE INSPECTION
IGNITION (5VZFE) IGNITION SYSTEM IGNITION SYSTEM ONVEHICLE INSPECTION NOTICE: IG1 IG00U07 Cold and Hot in these sentences express the temperature of the coils themselves. Cold is from 10 C (14 F) to 50
THROTTLE BODY. Port name. Clearance between lever and stop screw. 0 mm (0 in.) 0.50 mm (0.020 in.) 0.80 mm (0.031 in.) Throttle valve fully open
EG2236 ENGINE THROTTLE BODY ONVEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port. Start the engine. Check the vacuum with
REMOVAL FU 11 2TR-FE FUEL FUEL INJECTOR. Pinch. Checker. Detaching Switch Pull Out. Retainer. Fuel Hose Connector. Pipe. O-ring. Pinch.
2TR-FE EL EL INJECTOR 11 REMOVAL 1. DISCHARGE EL SYSTEM PRESSURE (See page -1) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1 4. DRAIN ENGINE COOLANT
ENGINE SPECIFICATIONS
ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)
CAMSHAFT POSITION SENSOR
IGNITION (2UZFE) CAMSHAFT POSITION SENSOR COMPONENTS CAMSHAFT POSITION SENSOR IG7 IG08T08 Drive Belt Camshaft Position Sensor Camshaft Position Sensor Connector Grommet Engine Wire Oil Cooler Pipe LH No.3
REMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
TURBOCHARGER SYSTEM TURBOCHARGER TC 1
TURBOCHARGER SYSTEM TURBOCHARGER TC1 TC2 TURBOCHARGER SYSTEM Description DESCRIPTION Systems which increase the amount of air sent to the engine are either turbocharger type (using exhaust gas to turn
ON-VEHICLE INSPECTION
CH2 P11586 CHARGING CHARGING SYSTEM ONVEHICLE INSPECTION 1. CHECK BATTERY ELECTROLYTE LEVEL Check the electrolyte quantity of each cell. MaintenanceFree Battery: CH03L01 If under the lower level, replace
ON-VEHICLE INSPECTION
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 G Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000017L8004X Title: 1GR-FE ENGINE MECHANICAL: ENGINE: ON-VEHICLE
Fuel System Diagnosis
Page 1 of 6 2001 Chevrolet Express Express, Savana (VIN G) Service Manual Engine Engine Controls - 5.0L and 5.7L Diagnostic Information and Procedures Document ID: 720867 Fuel System Diagnosis Circuit
GROUP 13C 13C-1 CONTENTS GENERAL DESCRIPTION... 13C-2 FUEL TANK... 13C-11 FUEL SUPPLY DIAGNOSIS... 13C-3 SPECIAL TOOLS... 13C-8
13C-1 GROUP 13C CONTENTS GENERAL DESCRIPTION......... 13C-2 DIAGNOSIS....... 13C-3 INTRODUCTION TO DIAGNOSIS........................ 13C-3 TROUBOLESHOOTING STRATEGY..... 13C-3 SYMPTOM CHART...................
EMISSION CONTROL SYSTEMS (2JZ GE) SYSTEM PURPOSE
SYSTEM PURPOSE The emission control systems are installed to reduce the amount of CO, HC and NOx exhausted from the engine ((3), (4) and (5)), to prevent the atmospheric release of blowby gascontaining
Brake Bleeding: Service and Repair
2008 Lexus GS 460 V8-4.6L (1UR-FSE) Copyright 2013, ALLDATA 10.52SS Page 1 Brake Bleeding: Service and Repair BRAKE: BRAKE FLUID (for 1UR-FSE): BLEEDING BRAKE: BRAKE FLUID CAUTION: Bleeding without the
Throttle Body (4A FE)
Air Induction System (Throttle Body (4AFE)) FI185 Throttle Body (4AFE) Throttle Position Sensor PSW E2 IDL ower oint oving oint F10451 P03147 F15040 F10452 Throttle Position Sensor Idle Point Guide Cam
INSPECTION. 3. INSPECT FUEL TANK CAP Visually check if the cap and/or gasket are deformed or damaged. If necessary, repair or replace the cap.
EC8 EMISSION CONTROL (2RZFE, 3RZFE) EC0LY01 INSPECTION 1. INSPECT LINES AND CONNECTIONS Visually check for loosen connections, sharp bends or damage. 2. INSPECT FUEL TANK Visually check for deformation,
Engine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
ON VEHICLE INSPECTION
IG 18 IGNITION SYSTEM (3VZ E) ON VEHICLE INSPECTION SPARK TEST CHECK THAT SPARK OCCURS (a) Disconnect high tension cord from the distributor. (b) Hold the end approx. 12.5 mm (0.50 in.) from engine ground
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1. CHECK OIL QUALITY LU1
ILLUSTRATION ILLUSTRATION
ILLUSTRATION ILLUSTRATION REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. When the brake pedal is depressed or the door courtesy switch is turned on even if the
HI-FLOW FUEL RAIL. Installation Instructions for: Part Numbers , ,
HI-FLOW FUEL RAIL Installation Instructions for: Part Numbers 25-100, 25-103, 25-112 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
INSPECTION. 3. INSPECT FUEL TANK CAP Visually check if the cap and/or gasket are deformed or damaged. If necessary, repair or replace the cap.
EMISSION CONTROL EC5 EC0E601 INSPECTION 1. INSPECT LINES AND CONNECTORS Visually check for loose connections, sharp bends or damage. 2. INSPECT FUEL TANK FILLER PIPE Visually check for deformation, cracks
KIT CONTENTS. Multimeter or test light Wire crimpers or soldering equipment. Wire terminals & connectors 10A inline fuse
RUSSELL FORD 5.0L COMPLETE EFI PLUMBING KIT INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new complete fuel system kit. If you have any questions, please call
ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS)
VSV for ACIS SFI (1GRFE) ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR CONTROL FUNCTION Intake Air Control Valve SF49 SF1Z001
Fuel System Diagnosis
1996 Chevrolet Impala Caprice, Impala, Roadmaster (VIN B) Service Manual Engine Engine Controls - 4.3L (Caprice Only) and 5.7L Diagnostic Information and Procedures Document ID: 37723 Fuel System Diagnosis
FUEL PRESSURE LEAK DOWN
2010 Dodge or Ram Truck RAM 1500 Truck 2WD V8-5.7L Vehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Fuel Pressure > Testing and Inspection > Component Tests and General Diagnostics
CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
COOLANT COOLANT INSPECTION HINT: Check the coolant level when the engine is cold. 1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR The engine coolant level should be between the LOW and FULL lines at
Throttle Body (3S GTE)
FI192 Air Induction System (Throttle Body (3SGTE)) Throttle Body (3SGTE) ONVEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port.
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
2010 Toyota Prius Repair Manual
REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,
REMOVAL AND INSTALLATION OF TRANSAXLE (4WD)
MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
ENGINE COMPONENTS AND TESTING (CONT'D) Checking Nozzle Injection Pressure. Fuel Injector Removal And Installation (Cont'd)
Fuel Injector Removal And Installation (Cont'd) Figure 70-70-9 Checking Nozzle Injection Pressure OEM064 - Injector Nozzle Tester Figure 70-70- P-5797 Remove the injector nozzle holder bolt (Item ) [Figure
Mazda3 - Workshop Manual - Engine
Page 1 of 18 2005 - Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks
7649A FUEL INJECTOR CLEANING SPECIALTY TOOLS USER MANUAL & REPLACEMENT PARTS LIST
7649A FUEL INJECTOR CLEANING SPECIALTY TOOLS USER MANUAL & REPLACEMENT PARTS LIST Safety Precautions WARNING: The following safety precautions must be carefully observed to reduce the risk of fire and
Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002
Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.
ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE
TIMING BELT COMPONENTS
EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
ENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE
GROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS...
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOL 14-2 ENGINE COOLING DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE
COOLING SYSTEM ON-VEHICLE INSPECTION CO 1
2GR-FE OLING OLING SYSTEM A133894 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK FOR ENGINE OLANT LEAKS CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized,
CONTINUITY TEST. Continuity Inspection. NOTE: Perform the following test only when directed.
2003 Mazda MX-5 Miata L4-1.8L DOHC Vehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Testing and Inspection > Component Tests and General Diagnostics CONTINUITY TEST FUEL
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L
Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions
8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
1. Seat 6. Side cover 11. Fuel pump retainer. 4. Mud guard 9. Fuel pump gasket : Do not reuse.
LT-A450** K8 ~ L0 LT-A500** K9 ~ L1 LT-A750** K8 ~ L1 Fuel Tank Removal, Inspection and Installation Procedure Necessary Tools Ratchet handle (9.5 sq) Socket wrench (10 mm, 9.5 sq) Socket wrench (12 mm,
1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
GENERATOR CH-9 COMPONENTS FOR REMOVAL AND INSTALLATION
CH9 COMPONENTS FOR REMOVAL AND INSTALLATION CH10 REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be started after 90 seconds
B-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL RETURN THIS TO: INITIAL HERE TECHNICIAN NO.
5 SERVICE BULLETIN B-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL It has come to the attention of Buell Distribution Corporation that a certain number of 2000 Model X1 and S3/T
TIME LAG TEST Check the automatic transmission (each clutch, brake and gear) for wear.
AT2 TROUBLESHOOTING 1. GENERAL INFORMATION (a) Troubles occurring with the automatic transmission can be caused by either the engine, electrical control or the transmission itself. These 3 areas should
TURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models
TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached
I - SYSTEM/COMPONENT TESTS
I - SYSTEM/COMPONENT TESTS 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - System & Component Testing 850 INTRODUCTION NOTE: In this article, Engine Control Module (ECM) may also be referred to as Engine
IGNITION SYSTEM IG 1 2GR-FE IGNITION IGNITION SYSTEM INSTRUMENT PANEL JUNCTION BLOCK - IG2 FUSE ECM
NITION SYSTEM EINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 INSTRUMENT PANEL JUNCTION BLOCK - 2 FUSE ECM EINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - 2 RELAY - AM2 FUSE A126956E01 2 2GR-FE
Oil Pan Seal Cutter Oil Filter Wrench Transmission & Transfer Bearing Replacer. ( ) Replacer Pipe
EG359 PREPARATION SST (SPECIAL SERVICE TOOLS) 0903200100 Oil Pan Seal Cutter No.2 oil pan 0922807500 Oil Filter Wrench 0931660010 Transmission & Transfer Bearing Replacer (0931600010) Replacer Pipe Crankshaft