DISASSEMBLY. Transmission. All vehicles

Size: px
Start display at page:

Download "DISASSEMBLY. Transmission. All vehicles"

Transcription

1 Automatic Transmission 5R44E and 5R55E DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission (T93T AH) Special Tool(s) Remover, Servo (T97T-7D021-A) Holding Fixture, Transmission (T57L-500-B) Handle, Torque Converter (T81P-7902-C) Remover, Transmission Extension Housing Bushing (T77L-7697-E) Retainer, Torque Converter (T97T-7902-A) All vehicles Slide Hammer (T50T-100-A) Remover, Torque Converter Fluid Seal (T94P BH) 1. WARNING: Do not remove the torque converter from the transmission while still on the jack. Doing so could cause the transmission to fall. Failure to follow these instructions may result in personal injury. Place the transmission on a workbench. Compressor, Servo Cover (T95L A) (Continued) Copyright 2002, Ford Motor Company Last updated: 06/12/2002

2 Automatic Transmission 5R44E and 5R55E Remove the special tool. 5. Remove the output shaft speed (OSS) sensor. 1 Remove the OSS screw. 2 Remove OSS sensor. 3. WARNING: The torque converter is heavy, especially when full of fluid. Failure to follow these instructions may result in personal injury. Using the special tool, remove the torque converter. 6. Remove the intermediate shaft speed sensor. 1 Remove the intermediate shaft speed screw. 2 Remove intermediate shaft speed sensor. 4. NOTE: The splines on the input shaft are not 7. If equipped, remove the heat shield. the same on both ends. The end with the 1 Remove the nut. shorter spline goes into the assembly. 2 Remove the heat shield. Remove the input shaft.

3 Automatic Transmission 5R44E and 5R55E Remove manual control outer lever nut and 11. NOTE: Remove the extension housing bushing manual control outer lever. only if service is required. Using the special tool, remove the extension housing bushing. Inspect the extension housing bushing and driveshaft slip yoke for nicks, gouges, scoring and wear. 9. Remove the digital transmission range (TR) sensor. 1 Remove the screws. 2 Remove the digital TR sensor. All vehicles 12. CAUTION: The parking pawl, parking pawl return spring and parking pawl shaft could fall out during removal of the extension housing. Remove the screws, studs and the extension housing. Discard the extension housing gasket. 4x2 vehicles 10. Using the special tools, remove the extension housing seal.

4 Automatic Transmission 5R44E and 5R55E Remove the parking pawl assembly. 1 Remove the parking pawl shaft. 2 Remove the parking pawl. 3 Remove the parking pawl return spring. 14. CAUTION: The parking pawl actuating rod must slip freely into the clearance hole in the adapter plate. Install the special tool. 16. WARNING: Make sure the lock pin on the special tool is secure. Failure to follow these instructions may result in personal injury. Install the transmission into the special tool. Rotate the transmission so the fluid pan is facing up. 17. CAUTION: Do not reuse the fluid pan gasket. Remove the transmission fluid pan screws, pan and transmission pan gasket and then discard the gasket. 15. Assemble the special tools.

5 Automatic Transmission 5R44E and 5R55E Remove the transmission fluid filter and discard. 1 Remove the screw. 2 Remove the transmission fluid filter. 19. Carefully lift up on the wire loom guide and protector. Disengage the retaining pins from the solenoid clamps. 21. Remove the manual control valve detent lever spring. 1 Remove the screw. 2 Remove the manual control valve detent lever spring. 20. Disconnect the solenoid electrical connectors. 1 Disconnect the SSA, SSB, SSC and SSD electrical connectors. 2 Disconnect the torque converter clutch (TCC) solenoid electrical connector. 3 Disconnect the electronic pressure control (EPC) solenoid electrical connector.

6 Automatic Transmission 5R44E and 5R55E Remove the low/reverse band servo cover. 1 Remove the screws. 2 Remove the low/reverse band servo cover and the low/reverse servo separator plate cover gasket. Discard the low/reverse servo separator plate cover gasket. 25. Remove the twenty-three valve body screws. 23. Remove the low/reverse band servo piston and rod assembly. 26. Remove the main control valve body, valve body separator plate and main control to separator plate gasket. Discard gaskets. 24. CAUTION: To prevent solenoid valves from falling out, do not remove the two screws shown below. Do not remove the two (gold colored) screws specified.

7 Automatic Transmission 5R44E and 5R55E CAUTION: Throw the locknuts away. The locknuts are not reusable for assembly. Remove the locknuts and the screws. 28. CAUTION: The servo cover is under spring tension. Using the special tool, remove the intermediate servo cover retaining ring. 30. CAUTION: Servo cover is under spring tension. Using the special tool, remove the overdrive servo retaining ring and cover. 29. NOTE: Tag the servo cover, piston and spring. Label accordingly for assembly. The covers have letters cast on the outer surface for identification. NOTE: Use the special tool to prevent damage to the servo, cover and bore. Using the special tool, remove the intermediate band servo piston, spring and cover. 31. NOTE: Tag the servo cover, piston and servo piston spring. Label accordingly for assembly. The covers have letters cast on the outer surface for identification. NOTE: Use the special tool to prevent damage to the servo piston and bore. Using the special tool, remove the overdrive band servo piston, spring and cover.

8 Automatic Transmission 5R44E and 5R55E WARNING: Make sure the lock pin on the special tool is secure. Failure to follow these instructions may result in personal injury. Rotate the transmission so the converter housing faces up. 33. CAUTION: Discard the screws. The screws are not reusable for assembly. Remove and discard the screws. 35. Remove the No. 1 fluid pump input thrust washer. 34. Remove the converter housing and fluid pump support. Turn and lift the converter housing and fluid pump support from the case.

9 Automatic Transmission 5R44E and 5R55E Compress the front band around the front brake and coast clutch drum and remove the front band anchor strut. 37. CAUTION: Identify the anchor and apply ends of the front band. Remove the front band. 40. NOTE: The front band lever shaft is longer than the intermediate band lever shaft. Remove the front band actuating lever shaft. 38. Remove the front brake and coast clutch drum. 41. CAUTION: Do not bend trigger wheel. NOTE: The No. 2 thrust bearing is in this assembly. Remove the planetary gear overdrive carrier. 39. Remove the front band apply strut.

10 Automatic Transmission 5R44E and 5R55E NOTE: Tag and identify the front band servo 45. NOTE: Tag and identify the No. 3 center shaft lever. The front band servo lever has a letter thrust bearing for assembly. stamped on the side. Remove the No. 3 center shaft thrust bearing. Remove the front band servo lever and front band lever to case bracket. 46. CAUTION: The center support locknut can fall into the remaining assembly if not 43. Remove the No. 2 front planet thrust bearing. removed. Remove the center support cap screw. 44. Remove the front ring gear, front one-way clutch assembly and center shaft as an assembly. 47. Remove the locknut and cage.

11 Automatic Transmission 5R44E and 5R55E CAUTION: Do not pry on other wires or damage the connector or case surface. Disconnect the turbine shaft speed (TSS) sensor electrical connector. 1 Remove the TSS sensor electrical connector from the transmission case (16-pin) electrical connector. 2 Remove the TSS sensor connector wires from wire locator. 49. CAUTION: Carefully route the TSS connector and wiring into the transmission through the opening in the case. 51. CAUTION: Do not damage the Remove the TSS sensor. connector or harness. 1 Remove the screw. Compress the tabs on the transmission case 2 Remove the TSS sensor. (16-pin) electrical connector. Push the transmission case (16-pin) electrical connector out of transmission case. 50. CAUTION: Do not overstretch the retaining spring. Remove the transmission case (16-pin) electrical connector retaining spring.

12 Automatic Transmission 5R44E and 5R55E Remove the center support retaining ring. 55. Remove the intermediate band anchor strut. 53. NOTE: When removing the center support, pull 56. CAUTION: Identify the anchor and evenly around the center support web. apply ends of the intermediate band. Remove the center support. Remove the intermediate band. 54. NOTE: Tag and identify the No. 4 intermediate 57. Remove the intermediate band apply strut. brake drum thrust bearing. Remove the No. 4 intermediate brake drum thrust bearing.

13 Automatic Transmission 5R44E and 5R55E NOTE: The intermediate band lever shaft is shorter than the front band lever shaft. Remove the intermediate band actuating lever shaft. 61. Remove the No. 5 forward clutch cylinder thrust bearing tag and identify. 59. NOTE: Tag and identify the intermediate servo band lever. The intermediate servo band lever has a letter stamped into its side. Remove the intermediate servo actuating lever. 62. Remove the forward clutch cylinder. 60. NOTE: The No. 5 forward clutch cylinder thrust bearing may come out with the intermediate brake and direct clutch drum. Remove the intermediate brake and direct clutch drum.

14 Automatic Transmission 5R44E and 5R55E Remove the No. 6A forward ring gear hub 66. NOTE: Check the black oxidized side during thrust bearing. removal to make sure of correct placement during reassembly. The black oxidized side must be toward planetary assembly. The uncoated side must face up. Remove the No. 7 forward planet thrust bearing. 64. Remove the forward ring gear and forward ring gear hub as an assembly. 67. Remove the forward planetary assembly. 65. Remove the No. 6B forward clutch thrust washer from the forward ring gear hub. 68. Remove input shell with the forward sun gear.

15 Automatic Transmission 5R44E and 5R55E NOTE: Tag and identify the No. 8 low/reverse 72. NOTE: Tag and identify the No. 9 low/reverse planetary carrier thrust bearing. planetary carrier thrust bearing. Remove the No. 8 low/reverse planetary carrier thrust bearing. Remove the No. 9 low/reverse planetary carrier thrust bearing. 70. Remove the low/reverse planetary retaining 73. Remove the output shaft sleeve. ring. 74. CAUTION: Discard the output shaft 71. Remove low/reverse planetary assembly. retaining ring. A new retaining ring must be used for assembly. Remove and discard the output shaft retaining ring.

16 Automatic Transmission 5R44E and 5R55E Remove the output shaft ring gear and the 78. Remove the reverse band. output shaft hub. 76. NOTE: Tag and identify the No. 10 output shaft hub thrust bearing. Remove the No. 10 output shaft thrust bearing. 79. Remove the output shaft. 80. Remove the park gear. 77. NOTE: The inner race of the rear one-way clutch is not removable. It is serviced in the case. Remove the low/reverse brake drum and one-way clutch assembly.

17 Automatic Transmission 5R44E and 5R55E NOTE: Tag and identify the No. 11 output 84. CAUTION: Do not damage the case shaft thrust washer. fluid pan rail. Remove the No. 11 output shaft thrust washer. Remove the manual control lever shaft spring pin. Tap lightly on each side of the manual control lever shaft spring pin with a drift punch. Pry the spring pin out of its bore. 82. CAUTION: To avoid damage, make sure wrench does not strike the manual valve inner lever pin. Remove the manual control valve inner lever nut. 85. Remove the manual control lever shaft. 83. Remove the manual control valve inner lever and the parking lever actuating rod.

18 Automatic Transmission 5R44E and 5R55E CAUTION: Do not damage the bore. Remove the manual control lever seal.

ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)

ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s) 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing

More information

ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)

ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s) 307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)

More information

Automatic Transmission 5R44E and 5R55E

Automatic Transmission 5R44E and 5R55E 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)

More information

Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission

More information

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B. «1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept

More information

2002 F-Super Duty /Excursion Workshop Manual

2002 F-Super Duty /Excursion Workshop Manual Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,

More information

2003 E-Series Workshop Manual

2003 E-Series Workshop Manual Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator

More information

Assembly. NOTE: Before beginning assembly, perform/inspect the following:

Assembly. NOTE: Before beginning assembly, perform/inspect the following: Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2

More information

1 of 25 9/12/2013 9:07 PM

1 of 25 9/12/2013 9:07 PM 1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the

More information

Page 1 of 10 Main Components and Functions Torque Converter 1 Cover (Part of 7902) 2 Converter Damper Plate 3 O-Ring (Part of 7902) 4 Turbine Assembly (Part of 7902) 5 Selective Spacer 6 Thrust Washer

More information

SECTION Automatic Transaxle/Transmission 6R80

SECTION Automatic Transaxle/Transmission 6R80 307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Transmission... 307-01-2 307-01-2 Automatic Transaxle/Transmission 6R80 307-01-2

More information

STEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin.

STEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin. 1999 Ford Truck Econoline E450 Super Duty V10-6.8L VIN S Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > 4R100 > Assembly STEPS 51-94 51. Install

More information

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission. 308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing

More information

Shift Solenoid B (SSB) and Shift Solenoid D (SSD) Inverse Proportional VFS 2761

Shift Solenoid B (SSB) and Shift Solenoid D (SSD) Inverse Proportional VFS 2761 Item Description 1 Shift Solenoid A (SSA) Variable Force Solenoid (VFS) 2 Shift Solenoid C (SSC) VFS SSB and SSD use inverse proportional operation. As the current from the PCM decreases, the pressure

More information

Description and Operation

Description and Operation Description and Operation Clean the automatic transmission to prevent dirt entering when it is reassembled. Lay the removed parts out clearly to make it easier to assess damage and reassemble components.

More information

Jatco 5 Speed ATRA. All Rights Reserved. Printed in U.S.A.

Jatco 5 Speed ATRA. All Rights Reserved. Printed in U.S.A. 1 2 3 Table Of Contents Transmission Diassembly... 4 Front Pump... 16 Reverse/High Clutch Drum... 18 Direct Clutch Drum... 22 Low Clutch Drum... 26 Planetary Gearsets... 29 Transfer Gear/Reduction Gear...

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control module (PCM) 1 Pressure control solenoid

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S

2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S 2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» 30-40LE (AW4) 4 Speed» Overhaul (Transmission)» Disassembly DISASSEMBLY

More information

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed.

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed. 1 INSTRUCTIONS TCI 274500/274501 4L80E Trans Brake Valve Body Thank you for choosing TCI products. We are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning

More information

2001 Chevrolet Corvette AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul

2001 Chevrolet Corvette AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul 2001-03 AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transmission installation. Oil cooling system contamination may cause premature

More information

4T80E. FWD 4 Speed Primary/Secondary Pump. 2-3 Accum. Valve Body Cover Channel Plate Upper Valve Body.

4T80E. FWD 4 Speed Primary/Secondary Pump. 2-3 Accum. Valve Body Cover Channel Plate Upper Valve Body. 4T80E FWD 4 Speed 2 190 A 191 54 55 250 Valve Body Cover 156 Primary/Secondary Pump 155 129 151 152 157 3 Upper Valve Body 2-3 Accum. 183 53 182 Channel Plate 20 21 60 135 91 195 72 73 B 33 2nd Clutch

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-01-1 Automatic Transmission 5R55S 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control Module (PCM) C175b 1 Shift Solenoid A (SSA)

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 26 Service Manual: AUTOMATIC TRANSAXLE - 4T65-E - OVERHAUL COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Case and Associated Parts Disassembled View (1 of 4) 2004 Buick LeSabre 3.8L Eng Limited

More information

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT

Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT PART NUMBER SC-46-47RHE-OS INSTALLATION GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Sure Cure kit contents.

More information

AUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul

AUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul 1997-98 AUTOMATIC TRANSMISSIONS General Motors Corp. Hydra-Matic 4L60-E Overhaul APPLICATION TRANSMISSION APPLICATIONS Application Corvette Transaxle 4L60-E IDENTIFICATION The 4L60-E transmission can be

More information

Welcome To Today s Presentation Sponsored By:

Welcome To Today s Presentation Sponsored By: Welcome To Today s Presentation Sponsored By: Any Questions Or Comments Please Send Emails To webinars@atra.com Any Questions That You May Have During The Webinar Please Feel Free To Text Them In At Any

More information

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K 2007 Jeep Truck Liberty 4WD V6 3.7L VIN K Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» Overhaul» Disassembly DISASSEMBLY NOTE: If the transmission is being

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer

More information

Subaru EC8 / 4EAT ( )

Subaru EC8 / 4EAT ( ) Subaru EC8 / 4EAT (1987-98) 4 Speed FWD / AWD 9 105 8 A Input Shaft Differential Differential Housing 10 Pinion 60 30 31 B Reverse Drum 82 95 83 High Drum Reverse Clutch 36 37 39 40 C Forward Hub 42 43

More information

DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3

DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3 2004 Mitsubishi Truck Endeavor V6-3.8L SOHC Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > F4A5A > Disassembly and Assembly DISASSEMBLY TRANSAXLE

More information

Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B

More information

Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd

Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd TCI 221500 Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd This Valve Body will neutralize at shut-down by putting shifter In 2nd gear position This Kit Contains: (1) Turbo

More information

Geo Prizm ( LSi) Toyota Celica 1.8L (1994)

Geo Prizm ( LSi) Toyota Celica 1.8L (1994) Page 1 of 140 ARTICLE BEGINNING APPLICATION TRANSMISSION APPLICATIONS Application Geo Prizm (1993-94 LSi) Toyota Celica 1.6L (1993) Celica 1.8L (1994) Celica 2.2L (1993) Corolla 1.8L MR2 Paseo Transaxle

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)

More information

TCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve.

TCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve. TCI 221100 Turbo 400 Full Manual Valve Body Shift Pattern: Park Reverse Neutral First Second Third This Kit Contains: (1) Turbo 400 Full Manual Valve Body (1) Separator Plate & Gaskets (1) Pressure Regulator

More information

27 E. Front wheel drive. 1. Transmission Description (Ford Focus 2000 only) 4 4 Speed Transmission F

27 E. Front wheel drive. 1. Transmission Description (Ford Focus 2000 only) 4 4 Speed Transmission F 1. Transmission Description (Ford Focus 2000 only) 4 4 Speed Transmission F Front wheel drive 27 E Maximum input torque after torque converter: 270 Lb-ft (365 N-m) Fully Electronic control Note: Mazda

More information

23. Planetary Gear and Low Clutch S510212

23. Planetary Gear and Low Clutch S510212 Automatic Transmission 23. Planetary Gear and Low Clutch S510212 A: REMOVAL S510212A18 1) Extract the torque converter clutch assembly. 2) Remove

More information

4T80E (MH1) ELECTRONIC 4 SPEED FWD

4T80E (MH1) ELECTRONIC 4 SPEED FWD 4T80E (MH1) 4 SPEED A B C D E F Deluxe Kit---------------------------------- 008 Compliance Kit ------------------------ 007 Master Kit -------------------------------- 006 Less Steel Kit --------------------------

More information

Direct Clutch Assembly 1263

Direct Clutch Assembly 1263 SECTION 307-01: Automatic Transaxle/Transmission 2006 F-53 Motorhome Chassis TorqShift Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 11/29/2004 Direct Clutch Assembly

More information

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul 2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle

More information

4L40E 4 SPEED, 5L40E 5 SPEED (M82), 5L50E (M22) - ELECTRONIC - RWD

4L40E 4 SPEED, 5L40E 5 SPEED (M82), 5L50E (M22) - ELECTRONIC - RWD A B C D E F 134 54 2008 Transtar Industries, Inc. No part of this work, including but not limited to the Part Numbers, may be reproduced or transmitted in any form or by any means, electronic or mechanical,

More information

DRIVE AXLES. Differentials & Axle Shafts - Corvette

DRIVE AXLES. Differentials & Axle Shafts - Corvette DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case

More information

5L40E/5L50E. RWD 5 Speed. RWD 5 Speed E 994. COPYRIGHT 2009 DACCO Incorporated. COPYRIGHT 2009 DACCO Incorporated 211* 878* 892* 507 Pump

5L40E/5L50E. RWD 5 Speed. RWD 5 Speed E 994. COPYRIGHT 2009 DACCO Incorporated. COPYRIGHT 2009 DACCO Incorporated 211* 878* 892* 507 Pump RWD 5 Speed 750 070 540 176 034 313 531 538 532 538 534 539 533 036 311 179 520 209 211* 556 046 RWD 5 Speed 565 966 338 965 975 985 879 127 126 878* 146 106 151 131 130 110 150 892* 535 A A 536 787 314

More information

5R110W (TorqShift)

5R110W (TorqShift) 5R110W (TorqShift) RWD 5 Speed 115 2 40 114 30 41 75 76 55 42 3 56 95 A Pump Body Stator 90 120 121 44 122 57 123 124 58 45 127 77 46 47 59 B Coast Diode Overdrive Planet Center Support 60 61 78 131 99

More information

1997 Explorer/Mountaineer

1997 Explorer/Mountaineer Page 1 of 9 Section 308-07C: Transfer Case All-Wheel Drive DISASSEMBLY AND ASSEMBLY 1997 Explorer/Mountaineer Workshop Manual Transfer Case Special Service Tool(s) Bearing Cone Replacer T88T-7025-B Bearing

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 307-01-1 Automatic Transaxle/Transmission 4R70E/4R75E 307-01-1 DISASSEMBLY AND ASSEMBLY Main Control Valve Body Disassembly Main Control Valve Body Disassembled View Item Part Number Description Item Part

More information

Subaru M41 / M41A. FWD 3 Speed 2WD / AWD. C Turbine Shaft Park Pawl. Linkage. Converter Reactor. Pinion. Bell Housing.

Subaru M41 / M41A. FWD 3 Speed 2WD / AWD. C Turbine Shaft Park Pawl. Linkage. Converter Reactor. Pinion. Bell Housing. Subaru M41 / M41A FWD 3 Speed 2WD / AWD Park Pawl A Linkage 10 11 B Converter Reactor Bell Housing 13 Pinion C Turbine Shaft Pump Shaft 30 31 D Ring Gear Rear Planet Low Sprag Forward Sun Gear Reverse

More information

AWTF80SC / 81SC (AF21/AF40-6)

AWTF80SC / 81SC (AF21/AF40-6) AWTF80SC / 81SC (AF21/AF40-6) FWD 6 Speed 15 35 11 10 40 41 65 50 66 A Pump Assembly 2-6 (B1) Brake Band 3-5 Reverse (C3) Drum 75 Filter 80 20 21 51 52 57 16 17 58 B 24 3-5 Reverse (C3) Clutch 25 81 Front

More information

FORD 6F50, 6F55 ZIP KIT

FORD 6F50, 6F55 ZIP KIT FORD 6F0, 6F ZIP KIT PART NUMBER 6F0-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. CAUTION: Ensure shuttle valve is installed

More information

SECTION Automatic Transaxle/Transmission 6R80

SECTION Automatic Transaxle/Transmission 6R80 307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Forward Clutch Assembly... 307-01-2 307-01-2 Automatic Transaxle/Transmission

More information

46RE, 46RH, 47RE, 47RH ZIP KIT

46RE, 46RH, 47RE, 47RH ZIP KIT 46RE, 46RH, 47RE, 47RH ZIP KIT PART NUMBER 46-47RHE-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. installation Diagram 7 1 Separator

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTALLATION GUIDE Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

Page 1 of 10 SECTION 307-01: Automatic Transaxle/Transmission 2005 Focus Workshop Manual ASSEMBLY Procedure revision date: 04/04/2008 Transaxle Printable View (2476 KB) Special Tool(s) Alignment Tool,

More information

GM 4L80-E, 4L85-E SURE CURE KIT

GM 4L80-E, 4L85-E SURE CURE KIT GM 4L80-E, 4L85-E SURE CURE KIT PART NUMBER SC-4L80E INSTRUCTION BOOKLET Parts are labeled here in order of installation. See page 2 for details on Sure Cure kit contents. See Sure Cure instruction booklet

More information

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet

More information

FORD 6F50, 6F55 ZIP KIT

FORD 6F50, 6F55 ZIP KIT FORD 6F0, 6F ZIP KIT PART NUMBER 6F0-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on kit contents. CAUTION: Ensure shuttle valve is installed with

More information

Transmission Electronic Control System

Transmission Electronic Control System SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/23/2008 Transmission Electronic Control System Electronic System

More information

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista

More information

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring.

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring. ASSEMBLY (AUTOMATIC 545RFE)... ASSEMBLY NOTE: Apply trans jell or petroleum jelly to all slide portions, rolling contacts surfaces, thrust surfaces etc. to prevent burnout during initial operation. Lubricate

More information

INDEX AUTOMATIC TRANSMISSION SERVICE GROUP SW 107TH AVENUE MIAMI, FLORIDA (305) Copyright ATSG 2004

INDEX AUTOMATIC TRANSMISSION SERVICE GROUP SW 107TH AVENUE MIAMI, FLORIDA (305) Copyright ATSG 2004 FORD E4OD "UPDATE HANDBOOK" INDEX VALVE BODY AND CHECKBALL CHANGES THRU 1996... 1989-1995 VALVE BODY CHECKBALL LOCATIONS... 1996 VALVE BODY CHECKBALL LOCATIONS... EARLY 1989 CASE CHECKBALL LOCATIONS...

More information

IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)

IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s) 205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072

More information

SECTION Automatic Transaxle/Transmission 6R80

SECTION Automatic Transaxle/Transmission 6R80 307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission 6R80 Main Control

More information

Interchanges are a fact of life for. Interchanges for the E4OD and 4R100 STREET SMART. by Mike Brown

Interchanges are a fact of life for. Interchanges for the E4OD and 4R100 STREET SMART. by Mike Brown STREET SMART by Mike Brown Interchanges for the E4OD and 4R100 Figure 1 Figure 2 Interchanges are a fact of life for transmission repair. Maybe you can t get the original part anymore; maybe you just can

More information

2002 F-150 Workshop Manual

2002 F-150 Workshop Manual Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)

More information

4T40E(MN4), 4T45E(MN5) - 4 SPEED TURBO HYDRAMATIC

4T40E(MN4), 4T45E(MN5) - 4 SPEED TURBO HYDRAMATIC 98 4T40E Chevrolet Cavalier/Pontiac Sunfire - 2.3L Quad 4 95-Up Oldsmobile Achieva/Cutlass 98-Up Chevrolet Malibu 98-Up Saturn LS - 4 Cyl. - 4T40E(MN4) 00-Up Saturn LS - 6 cyl. - 4T45E(MN5) 00-Up 12 Bolt

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

6F50 / 6F55 / 6T70 / 6T75

6F50 / 6F55 / 6T70 / 6T75 6F50 / 6F55 / 6T70 / 6T75 FWD 6 Speed 42 80 81 82 83 43 A 41 Differential 84 85 86 87 B 60 Driven Transfer Pinion 50 70 51 169 51 70 C 117 61 139 140 D 5 100 62 Pump Drive 141 90 142 Drive Transfer 71

More information

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch: 20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their

More information

1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission

1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission 1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision

More information

Single-Reduction Forward Differential Carriers on Tandem and Tridem Axles

Single-Reduction Forward Differential Carriers on Tandem and Tridem Axles Maintenance Manual 5L Single-Reduction Forward Differential Carriers on Tandem and Tridem Axles Revised 12-10 Service Notes About This Manual This manual provides maintenance and service information for

More information

Off-Highway Axle Planetary Wheel Ends

Off-Highway Axle Planetary Wheel Ends Maintenance Manual MM-1189 Off-Highway Axle Planetary Wheel Ends Revised 06-16 Service Notes About This Manual This manual provides service and repair procedures for planetary wheel ends on off-highway

More information

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed)

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) 24 00 585 Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) Secure transmission to assembly frame with special tool 24 0 180. Drain off transmission oil. Screw special

More information

TC20 Chain Driven Power Take-Off Overhaul Instructions

TC20 Chain Driven Power Take-Off Overhaul Instructions TC20 Chain Driven Power Take-Off Overhaul Instructions Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 General Information 5 Special Tools 6 Disassembly See Page 2 Reassembly See

More information

ABBREVIATIONS USED IN THIS

ABBREVIATIONS USED IN THIS IN10 INTRODUCTION ABBREVIATIONS USED IN THIS MANUAL ABBREVIATIONS USED IN THIS MANUAL ATF Automatic Transmission Fluid B 0 Overdrive Brake B 2 Second Brake B 3 No. 3 Brake C 0 Overdrive Direct Clutch C

More information

FORD 6R80 UPDATES Presented by: David Chalker ATRA Technical Advisor 6R80

FORD 6R80 UPDATES Presented by: David Chalker ATRA Technical Advisor 6R80 FORD UPDATES Presented by: David Chalker ATRA Technical Advisor Welcome To Today s Presentation Sponsored By: Any Questions Or Comments Please Send Emails To webinars@atra.com Any Questions That You

More information

JF506E (JA5A-EL/5F31J/RE5F01A/09A)

JF506E (JA5A-EL/5F31J/RE5F01A/09A) FWD 5 Speed FWD 5 Speed 750 699 284 730 281 712 281 796 282 280 869 283 586 596 868 616 864 866 142 561 961 331 981 865 971 330 122 551 040 257 862 650 180 260 261 259 022 790 A A 698 715 077 293* 292

More information

Zoom and Print Options

Zoom and Print Options 1 of 63 8/26/2017, 7:04 AM Vehicle» Transmission and Drivetrain» Transfer Case» Service and Repair» Procedures» Isuzu T150» Overhaul (Unit Repair)» 1. Transfer Case Disassemble Transfer Case Disassemble

More information

Chrysler 48RE SURE CURE KIT

Chrysler 48RE SURE CURE KIT Chrysler 48RE SURE CURE KIT PART NUMBER SC-48RE INSTALLATION GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Sure Cure kit contents. See Sure Cure instruction

More information

ABBREVIATIONS USED IN THIS MANUAL

ABBREVIATIONS USED IN THIS MANUAL IN6 INTRODUCTION Abbreviations Used in This Manual ABBREVIATIONS USED IN THIS MANUAL A/T ATM Automatic Transmission ATF Automatic Transmission Fluid B 0 Overdrive Brake B 1 Second Coast Brake B 2 Second

More information

AUTOMATIC TRANSMISSION - 42RLE

AUTOMATIC TRANSMISSION - 42RLE TJ AUTOMATIC TRANSMISSION - 42RLE 21-37 AUTOMATIC TRANSMISSION - 42RLE TABLE OF CONTENTS page AUTOMATIC TRANSMISSION - 42RLE DESCRIPTION...38 OPERATION...40 DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING

More information

GENERAL SPECIFICATIONS

GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION - DESCRIPTION AT-3 GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION -COMPONENT PARTS REMOVAL COMPONENT PARTS REMOVAL COMPONENTS AT-13 Oil Cooler Union Throttle Cable O-Ring A/T Fluid

More information

SECTION B Manual Transaxle/Transmission TR6060

SECTION B Manual Transaxle/Transmission TR6060 308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2

More information

2007 Dodge Nitro R/T

2007 Dodge Nitro R/T ASSEMBLY AUTOMATIC TRANSMISSION - 42RLE NOTE: If the transmission assembly is being reconditioned (clutch/seal replacement) or replaced, it is necessary to perform the TCM QUICK LEARN Procedure using the

More information

TRANSMISSION PARTS Instructions

TRANSMISSION PARTS Instructions TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-4T65E GM 4T65-E Valve Body Parts Boost Valve Kit 84754-30K Patent No. 6,832,632 TCC Apply Valve Kit 84754-43K Patent No. 7,100,753 TCC Regulated

More information

Rear Axle Hub, Bearing, Cup, and/or Seal Replacement

Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Page 1 of 11 Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools J 8092 Universal Driver Handle - 3/4 inch - 10 J 2222-C Wheel Bearing Nut Wrench J 24426 Wheel Bearing Race Installer - Outer

More information

Fluid Pump. Special Tool(s) Alignment Gauge, Transmission Fluid Pump Alignment Gauge, Transmission Fluid Pump

Fluid Pump. Special Tool(s) Alignment Gauge, Transmission Fluid Pump Alignment Gauge, Transmission Fluid Pump SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 06/30/2009 Fluid Pump Special Tool(s) Alignment Gauge,

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Pinpoint Tests OSC Equipped Vehicle Special Tool(s) Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A) Special Tool(s) MLP-TR

More information

AUTOMATIC TRANSAXLE AUTOMATIC TRANSAXLE SYSTEM... COMPONENT PARTS...

AUTOMATIC TRANSAXLE AUTOMATIC TRANSAXLE SYSTEM... COMPONENT PARTS... SYSTEM....... COMPONENT PARTS.................... OIL PUMP.............................. DIRECT CLUTCH........................ FORWARD CLUTCH..................... SECOND BRAKE........................ UNDERDRIVE

More information

STERNDRIVE UNIT 3 B GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS

STERNDRIVE UNIT 3 B GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS STERNDRIVE UNIT 3 B 23146 GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS Table of Contents Page Identification........................... 3B-1 Specifications.......................... 3B-1 Torque Specifications................

More information

4T65E. FWD 4 Speed. E Final Drive Sun Gear Shaft Final Drive Ring Gear Output Shaft. Side Cover. 2nd Clutch Drum. Support

4T65E. FWD 4 Speed. E Final Drive Sun Gear Shaft Final Drive Ring Gear Output Shaft. Side Cover. 2nd Clutch Drum. Support 4T65E FWD 4 Speed 2 102 181 185 187 183 182 182 186 141 150 300 150 A 3 184 B Side Cover Output Shaft 153 152 151 267 69 125 97 135 268 70 71 146 38 39 37 36 40 C Support Rev. Band 2nd Clutch Drum 2nd

More information

AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL. Fabco Automotive Corporation,

AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL. Fabco Automotive Corporation, AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL Fabco Automotive Corporation, TABLE OF CONTENTS SECTION TC-142 PD TRANSFER CASE SERVICE MANUAL Introduction Operation Specification LUBRICATION

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-01B-1 DIAGNOSIS AND TESTING Special Testing Procedures The special tests are designed to aid the technician in diagnosing the hydraulic and mechanical portion of the transmission. Engine Idle speed

More information

AUTOMATIC TRANSMISSIONS ZF 4HP 18

AUTOMATIC TRANSMISSIONS ZF 4HP 18 AUTO TRANS OVERHAUL - ZF 4HP 18 Article Text 1991 Eagle Premier For Dan's Transmission Service 10 Jefferson Place Fort Walton Beach FL 32548 1997 Mitchell Repair Information Company, All Rights Reserved.

More information