Series 270. Commercial Miniature 5/8" (16mm) Diameter Composition Variable Resistors. Electrical and Mechanical Specifications.
|
|
|
- Verity Mitchell
- 6 years ago
- Views:
Transcription
1 Series 270 Commercial Miniature 5/8" (16mm) Diameter Composition Variable Resistors Miniature 5/8" (16mm) size Versatile mounting styles: bushing twist tab bend tab snap-in PC bracket solder lug or PC terminals (shaft parallel or perpendicular to the panel) 100 Ω to 5 Meg Ω resistance range Molded or metal shafts SPST power switches Single, tandem, or concentric units Panel seal Rear extended shaft Electrical and Mechanical Specifications Resistance Range 100 Ω through 5 Meg Ω (linear taper). Resistance Tolerance Standard: ±20% Special: Other tolerances available in most resistance values. Power Rating, Watts 1 /4 watt per section through 100K 1 /5 watt per section above 100K Full 55 C derated to no load at 85 C, linear taper, bushing mounted control on steel panel 4" x 4" x.050" (101.6mm x 101.6mm x 1.27mm). (Derating required on two section controls.) Voltage Rating Bushings to Terminals: High pot test, one minute 750 VAC Operating maximum 500 VDC Across End Terminals: 350 VDC, load not to exceed listed wattage ratings. Resistance Tapers Standard: Linear, 10% Audio and 10% CCW Audio Special tapers available to meet most requirements Angle of Rotation Total Rotation Without Switch: 300 ± 5 With Switch: 315 ± 5 Effective Rotation Without Switch: 300 (approximate) With Switch: 290 (approximate) Panel Mounting Information Bushing Mount Standard: Brass (continued on next page) Technical Data Sheet 1448C Technical Data Sheet 1270E CTS CORPORATION / MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS
2 Electrical and Mechanical Specifications (continued) All Other Mounts Standard: Twist tab (designated by 1 ) Special: Bend tab 2 or 3 ears Bracket mounted Suggested Panel for Twist Tab.042" thick (1.07mm) Locating Lugs (Bushing Mount) Standard:.312" (7.9mm) radius from center of control. Special:.375" (9.53mm) radius from center of control. Standard Position: Left side supplied unless otherwise specified. Other Positions: Available with lug right side, without lugs, or with lugs both left and right sides. Water Seal Construction Controls are also available to prevent water from entering the control through either the O.D. of shaft and/or the bushing. Shaft and Bushing Information Bushing Lengths Available Standard:.187" or.250" (4.75mm or 6.35mm) Special:.125" increments (3.2mm increments) Thread Size Standard: 1 /4" 32 3 /8" 32 M7 x.75 M8 x.75p Special: As required Molded Shafts Available (Shown with preferred diameter bushing) Bushing Mounted or Ear Mounted SHAFT DIAMETER BUSHING DIAMETER /4" 32 M7X M7X /8" 32 M8X /8" 32 M9X.75 Metal Shafts Available (Shown with preferred diameter bushing) Single or Dual Units SHAFT DIAMETER BUSHING DIAMETER /4" 32 M7X /4" 32 M7X /8" 32 M7X /8" 32 M8X /8" 32 M9X.75 Concentric Tandem Units Available in two combinations: A.125" (3.2mm) diameter rear shaft.250" (6.35mm) panel shaft (3/8 32 or M9X.75) B.156" (4.0mm) diameter rear shaft.236" (6.0mm) diameter panel shaft (3/8 32 or M8X.75) Most metal shaft diameters can be used with twist tab mountings. With bracket mount, only.187 diameter shafts are used, with turn-down available to obtain smaller diameters. Metal Lengths: Minimum.125" (3.2mm) beyond bushing; special lengths as required. Trims: Plain round screwdriver slotted, flatted, knurled. Other trims available upon request. Molded Flatted and knurled with screwdriver slot available in many lengths and diameters. Terminal Information Standard: T Solder lug formed 90 to the rear. Special: (See below) T: Solder lug perpendicular to shaft. T: Solder lug formed 60 to the rear. U: PC terminals formed 90 forward toward mounting surface. Terminals extend.187" (4.7mm) beyond mounting surface. V: PC terminals formed 90 to the rear, away from panel mounting. Terminals extend.520" (13.2mm) from mounting surface. W: Wire wrap terminals.156" (4.0mm) terminal extension beyond base, formed 60 to the rear. BX: PC terminals standard.438" (11.1mm) from center line of control to PC board; straight terminals extend.156" (4.0mm) into PC board. X: PC terminals standard.505" (12.8mm) from center line of control to PC board, with.136" (3.4mm) straight terminal extension beyond PC board standoff. Y: PC terminals standard.602" (15.3mm) from centerline of control to PC board, with.140" (3.5mm) straight terminal extension beyond PC board standoff. (continued on next page)
3 Electrical and Mechanical Specifications (continued) Power Switches Available (all SPST) ELECTRICAL SERIES TYPE RATING 057 Rotary 20 VDC 057 Rotary 125 VAC (UL approved) Switch Actuating Angle -25 Switch Actuating Torque - 2 to 10 in. oz. (144 to 720g-cm) ELECTRICAL SERIES TYPE RATING DEMI Push-Pull 20 VDC DEMI Momentary contact 20 VDC Push on
4 T270 Solder Lug Terminals, Metal Shaft, Bushing Mount BX PM270 PC Type Base X Terminals, 2-Ear Mount Bend Tab, Molded Shaft UPE 270RE PC Type U Terminals, Twist Tab Mount, Metal Shaft, Rear Extension XB275RE PC Type X Terminals, Metal Shaft, Rear Extension
5 VPE 270 PC Type V Terminals, Twist Tab Mount, Metal Shaft X057-BX270 PC Type Terminal SPST Switch, PC Style Base X Terminals, Metal Shaft, Bushing Mount T2-270 Solder Lug Terminals, Straight Tandem, Metal Shaft, Bushing Mount XP275 PC Type X Terminal, Metal Shaft, Twist Tab Mounting
6 T057-C2-270 Solder Lug Terminal SPST Switch, Solder Lug Terminals, Concentric Metal Shafts, Bushing Mount Ordering Information 270/275 T 2 20 R 103 B 1 A 1 TERMINAL STYLE T SOLDER LUG X PC* U FORMED TO FRONT V FORMED TO REAR W FORMED TO REAR Order From: MOUNTING STYLE BUSHING LENGTH: 1/8" (3.2) INCREMENTS EXAMPLES: 2.250" (6.35) 3.375" (9.5) " (25.4) 1 TWIST TAB MOUNT BUSHING MOUNT SUPPLIED WITH LOCATING LUG LEFT SIDE TERMINALS DOWN *BX construction and terminal length supplied unless otherwise specified SHAFT LENGTH From Mounting Surface 1/32" (0.8mm) Increments Examples: Metal Shafts " (15.9) " (19.1) " (22.2) " (25.4) Moulded Shafts Limited Lengths Available, See Shaft Trim selection 16 Shaft U,.500" (12.7) 28 Shaft V,.875" (22.2) 32 Shaft W,.1.0" (25) SHAFT TRIM A.125" DIAM. ROUND BRASS B.125" DIAM. FLAT BRASS C.125" DIAM. SD SLOT BRASS R.156" DIAM. ROUND BRASS F.156" DIAM. FLAT BRASS S.156" DIAM. SD SLOT BRASS G.187" DIAM. ROUND BRASS H.187" DIAM. FLAT BRASS J.187" DIAM. SD SLOT BRASS X.236" DIAM. ROUND BRASS L.236" DIAM. FLAT BRASS M.236" DIAM. SD SLOT BRASS N.236" DIAM. SK BRASS P.250" DIAM. ROUND BRASS D.250" DIAM. FLAT BRASS E.250" DIAM. SD SLOT BRASS T.250" DIAM. SK BRASS U.187" DIAM..500" FMS SK MOLDED V.187" DIAM..875" FMS FLAT MOLDED W.236" DIAM..984" FMS FLATTED (.472" X.177") MOLDED K.236" DIAM..500" FMS SK MOLDED (SWITCH ONLY) RESISTANCE CODE EXAMPLES CODE RESISTANCE OHMS 102 1K K 502 5K K K K K RESIST TOL A ±10% B ±20% C ±30% TAPER 1 LINEAR 2 10% AUD 3 10% CCW AUD SWITCH TYPE A NONE B SPST ROTARY SPECIALS 1 NONE 2 50% DETENT 4 LOCATING LUG FOR RIGHT SIDE 5 NO LOCATING LUG NOTES: 275 series available in X and U style PC Terminals only..125 dia. &.156 dia. shaft thickness is dia. shaft flat thickness is dia. shaft flat thickness is dia. shaft flat thickness is.156. CTS CORPORATION, RESISTOR/ELECTROCOMPONENTS / 1601 Mishawaka Street / Elkhart, Indiana North America Toll Free (888) / (219) / FAX: (219) CTS COMPONENTS TAIWAN, LTD. / 7, Central 6th Road (Chung Liu Road) / P.O. Box Kaohsiung Export Processing Zone / Kaohsiung, Taiwan, Rep. of China (07) / FAX: (07) /00I
Rotary Potentiometer. 1/2 Watt, Composition. Electrocomponents. Industrial 24mm Diameter. Rotary Potentiometer. Features
Electrocomponents Series 450 Data Sheet Rotary Potentiometer Industrial 4 Diameter 1/ Watt, Composition Rotary Potentiometer Features - Bushing - Twist or Bend Tab - Snap-in PC Bracket - PC Terminal Electrical
Series 308 Electrical Specifications
Series 38 Potentiometer 1/2 in. sq..5 Watt Series 39 Potentiometer 1/2 in. sq. 1. Watt Description The Series 38 and 39 are high-performance, low-cost potentiometers. They are also available with S.P.S.T.
24mm Diameter, Single-Turn, Carbon Industrial Panel Controls
TOCOS PANEL CONTROLS 24mm Diameter, Single-Turn, Carbon Industrial Panel Controls RV24YN RV24YGME RVT24YN Features 24mm diameter, single-turn industrial panel controls Carbon film element Linear or audio
30mm Diameter, Single-Turn, Wirewound Industrial Panel Controls RA30YME RA30YD RA30Y
TOCOS PANEL CONTROLS 30mm Diameter, Single-Turn, Wirewound Industrial Panel Controls RA30YME RA30YD RA30Y Features 30mm diameter, single-turn industrial panel controls Wirewound element Linear or audio
POTENTIOMETERS ENCODERS & CODED SWITCHES TP/RH7& TP/RH9.
POTENTIOMETERS ENCODERS & CODED SWITCHES TP/RH7& TP/RH9 www.tocos.com We are TOCOS TOCOS America, Inc. is a wholly owned subsidiary of Tokyo Cosmos Electric Co., Ltd. ( TOCOS), a worldwide supplier of
mm Square Sealed Panel Control
*RoHS COMPLIANT Features Conductive plastic PC board and bushing mount Plastic or metal bushing and plastic shaft Withstands typical industrial washing processes Compact package saves board and panel space
Single Turn Rotary Wirewound Potentiometers
Single Turn Rotary Wirewound Potentiometers THE POTENTIOMETER SPEILISTS QD & QDD Series 1.328" Diameter, 3 watts, Single or Dual Module... pg. 2 Suggested replacement for Honeywell R20 and 43-Series QE
Features Metal shaft and bushing Consistent, smooth quality feel Up to 4 sections available Rotary switch option designed for on-off function control
*RoHS COMPLIANT VERSIONS AVAILABLE Features Metal shaft and bushing Consistent, smooth quality feel Up to sections available Rotary switch option designed for on-off function control RoHS compliant versions
Series S127B Potentiometer 1/2" (12.7mm) Square
Series S17 Potentiometer 1/" (1.7mm) Square Features: Stackable - up to modules onductive Plastic or ermet Resistance lement Linear, W or audio Taper Metal Shaft and ushing Description: The Series S17
A Series 1-4 Pole Rotary Switches
1-4 Pole Switches Features/Benefits Multi-pole and multi-position Positive detent Shorting & non-shorting contacts Panel and PCB mounting RoHS Compliant Typical Applications Automotive Major and small
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Features/Benefits Multi-pole and multi-position Positive detent Shorting
Security Switches. Anti Vandal, Pushbutton. Specifications. Specifications S76 S77. Features.748 (19mm) bushing diameter
Anti Vandal, Pushbutton S76.287 (7.3) c: Screw (Assembled).098 (2.5) Typ.142 (3.6) Type Circuitry Action Actuator g 54 377 SPST NO OFF (ON) Stainless Steel, Flat S76b 54 378 SPST NO OFF (ON) Stainless
ELUMILED.COM. Model 91, 92, 93, 94 & 95-5/8 Square Single-Turn Panel Control
*ohs COMPLIANT VESIONS AVAILABLE Features Available in a variety of pin-out configurations Virtually infinite electrical circuit isolation Metal or plastic shaft options ohs compliant versions available*
n Available in a variety of pin-out configurations
*ohs COMPLIANT Features n Available in a variety of pin-out configurations n Virtually infinite electrical circuit isolation n Metal or plastic shaft options n ohs compliant* Model 91, 9, 93, 94 & 95-5/8
Series 70 Custom Potentiometer Designer Guide
Series 70 Custom Potentiometer Designer Guide.05 [0.8mm] /8 [.8mm].50 [6.5mm].055 [.7mm] 6 ROUTE 0, STE 6 EST HNOVER NEW JERSEY 0796 Phone Internet POT PROTOTYPES PRONTO! Dual Potentiometer, Dual Rotary
ROTARY SWITCHES. Quality Features: LIGHTED ROTARY UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.
SWITCH R2 UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.83 PANEL CUTOUT Used in the heavy equipment, marine, process control and instrumentation markets the R2 rotary switch
T he Cole Series P3900 miniature P.C. termination rotary switch
P3900 series T he Cole Series P3900 miniature P.C. termination rotary switch is designed to provide the ultimate mechanical and electrical reliability in instrumentation, industrial controls, medical equipment,
T he Cole Series S3900 miniature P.C. termination rotary switch
S3900 series T he Cole Series S3900 miniature P.C. termination rotary switch is designed to provide the ultimate mechanical and electrical reliability in instrumentation, industrial controls, medical equipment,
CIT SWITCHTM ANT SPECIFICATIONS
Wide variety of applications from consumer electronics to commercial Standard epoxy sealed terminations Gold contacts available for low power applications Available support brackets for greater stability
or 0.5Ω whichever is greater (152 only) Temperature Coefficient of Resistance MODEL 152 MODEL 159 Refer to standard
Model 152, 159 FEATURES Rugged, High-Quality, All Metal Housing Short Length Behind Panel (11/32 ) Choice of Two Elements for Broad Resistance Range- 5Ω to 2MΩ No Glued Joints Extra Taps AVAILABLE High
Custom Potentiometer Designer Guide
Custom Potentiometer Designer Guide.015 [0.38mm] 1/8 [3.18mm].250 [6.35mm].055 [1.47mm] 36 Route 10 East Hanover New Jersey 07936 Phone POT PROTOTYPES PRONTO! Now almost any special combination potentiometer
Fig. 3. Actuator Style LED Tip LED Tip. Fig. 5. Lamp. Actuator Color. Style. LED Oval Rocker Lighted Blue LED
LIGHTED TOGGLES Fig. -00-0 -0-0 - - - - - - - - -0 - - - Fig. Figure -00-BU -0-BU -0-BU -0-BU --BU --BU --BU --BU --BU --BU --BU --BU -0-BU --BU --BU --BU Poles/ AMPS Throws VDC Fig. Fig. Style LED Duckbill
mm Square Sealed Panel Control
*RoHS COMPLIANT Features n Conductive plastic n PC board and bushing mount n Plastic or metal bushing and plastic shaft n Withstands typical industrial washing processes n Compact package saves board and
9000 SERIES SUBMINIATURE MOMENTARY PUSHBUTTON SWITCHES Overview
A 9000 SERIES Overview 9 SERIES Number of poles 3 Single pole Electrical functions 2 Normally closed (NC) 3 Normally open (NO) Terminals, case and bushing Case height 8 (.314) 2 Straight terminals - threaded
PLK & PLR SERIES Professional keylock or rotary switches
ISO OO AFAQ N /77c PLK & PLR SERIES Professional keylock or rotary switches NEW RANGE Miniature & subminiature to positions to poles PLK - PLR SERIES PROFESSIONAL KEYLOCK OR ROTARY SWITCHES Distinctive
M Series Half-inch Rotary Switches
Half-inch Switches Features/Benefits Multi-pole and multi-positions Panel and PCB mounting Stainless steel actuator Non-shorting contacts RoHS Compliant IP67 (F option only) Typical Applications Test equipment
ANT. Materials. Features. Miniature Toggle
Specificationscations RoHS Compliant ANT Electrical Ratings Electrical Life Contact Resistance 5A @ 0VAC, 8VDC A @ 50VAC See Contact Options 50,000 cycles typical
1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
Series 388/389 Custom Potentiometer Designer Guide
Series 88/89 ustom Potentiometer Designer Guide.05 [0.8mm] /8 [.8mm].50 [6.5mm].055 [.7mm] 6 ROUTE 0, STE 6 EST HNOVER NEW JERSEY 0796 Phone 97-887-550 Toll Free -800-6-808 Fax 97-887-90 Internet POT PROTOTYPES
Section 26: Capacitors, Resistors, Potentiometers, Trimmers. Capacitors Resistors Potentiometers Trimmers...
Section 26: Capacitors, Resistors, Potentiometers, Trimmers Sub-Section Page Capacitors.....................................................680 Resistors......................................................681
Series 300. Miniature Rocker & Paddle Switches
Series 00 SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 0,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. inital @ -VDC. 00mA for both
8500 Series Subminiature Pushbutton Switches
Subminiature Switches Features/Benefits Pre-travel or over-travel models available Ratings up to 3 AMPS Reliable contact design RoHS compliant Typical Applications Detection Telecommunications and networking
C&K 1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
7000 Series Miniature Rocker & Lever Handle Switches
Miniature & Lever Handle Switches Features/Benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoHS compliant
(RMG50) TO-220 Low-Profile Power Resistors. Token Electronics Industry Co., Ltd. Version: January 12, Web:
Version: January 12, 2017 (RMG50) TO-220 Low-Profile Power Resistors Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: rfq@token.com.tw Taiwan: No.137, Sec. 1, Zhongxing Rd., Wugu District,
Series 70 Custom Potentiometer Designer Guide
Series 70 ustom Potentiometer Designer Guide.05 [0.8mm] /8 [.8mm].50 [6.5mm].055 [.7mm] 6 ROUTE 0, STE 6 EST HNOVER NEW JERSEY 0796 Phone 97-887-550 Toll Free -800-6-808 Fax 97-887-90 Internet http://www.potentiometers.com
ELECTRO-MECHANICAL MINIATURE SEALED. Long life Solder or PC terminals PanelsealedtoIP67
PUSHBUTTON SWITCHES ELECTRO-MECHANICAL MINIATURE SEALED SERIES 48EM: ACTUAL SIZE FLEX-TECH MINIATURE SEALED PUSHBUTTON SWITCHES This rugged multi-option sealed pushbutton series offers the utmost in choices
Snap Action Miniature Pushbutton Switches
Snap Action Miniature Switches SERIES 38C Miniature Switches FEATURES and Circuitry Choice of Bushings, and Terminations Caps and Frames Available UL Recoginized DIMENSIONS IN INCHES (AND MILLIMETERS)
OW20BU/B4PC1S OW20BU/N4PC1S-CH *
OW20BU/B4PC1S OW20BU/N4PC1S-CH * B4OW1S N4PC1S 4 Amp Single Pole Switch CH Change Over (Double Throw) OW Ordinary Wiring (recommended for soldering) PC For Printed Circuit * Representative of range: Switch
2SS/2S1/2SM SUB-MINIATURE TOGGLES
2SS/2S1/2SM 2S-Series SUB-MINIATURE TOGGLES The 2S family of sub-miniature toggle switches is composed of three switch series; the 2S1-Series toggle switch, the 2SS-Series sealed toggle switch, and the
Rotary Switches Product Selection Guide
Switches Product Selection Guide Series A RTA M R F H RW RM ENC Switch Type Multi-pole/ Multi-position Multi-pole/ Multi-position Half-inch Rota-slide Rota-slide Power Rota-slide Subminiature SMT Subminiature
SPECIFICATIONS MATERIALS. NONE = Black WHT= White RED = Red M1 M3 M5. YEL = Yellow. GRY = Gray PUR = Purple. **Contact E-Switch for additional colors
SERIES 300 AND PADDLE - MINIATURE FEATURES & BENEFITS Multiple rocker & paddle options Up to 4 poles Multiple termination options Snap-in panel mount option available HOW TO ORDER APPLICATIONS/MARKETS
9 mm Multi-Ganged Potentiometer
9 mm Multi-Ganged Potentiometer QUICK REFERENCE DATA Multiple module Up to 7 modules Switch module n/a Detent module Yes Special electrical laws A: linear, L: logarithmic, F: reverse logarithmic and others
A Type Switch Assemblies. With Silver - Plated Brass Contacts and Solder Terminals
A Type 1 inch diameter switches with Electroswitch patented Unidex detent for positive action, feel and torque control. Double-wiping, self-cleaning contacts in silver plated brass, or silver alloy. Unique
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C&K ET Series Sealed Subminiature Switches Features/Benefits Sealed against
C&K 7000 Series Miniature Rocker & Lever Handle Switches
Features/Benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy sealed terminals prevent contamination during soldering Typical Applications Telecommunications Instrumentation
Switches. SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY 115VAC, 28VDC)
SWITCH SELECTION GUIDE Toggle Switches SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY (Resistive @ 115VAC, 28VDC) T1 2 or 3 Position, Momentary, 8A MIL-PRF-83731 15/32" or 1/4" dia.
7000 Series Miniature Rocker & Lever Handle Switches
Features/Benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoHS compliant Typical Applications Telecommunications
Fuseholders PAGE. Fuseholders.
PAGE International Shock-Safe (Panel Mount).......................................................................... 467-468 Flip-Top Shock-Safe (Panel Mount)..................................................................................
1/2" (12.7 mm) Conductive Plastic and Cermet Potentiometers
, /" 7 mm Conductive Plastic and Cermet FEATURES Robust construction High rotational life cycles Up to three sections PC support plates Rotary switches and solder lugs terminals available Compliant to
C&K E Series Sealed Miniature Toggle Switches
Sealed Miniature Switches eatures/benefits Sealed against solder and cleaning process contaminants UL 94V-0 Nylon case and bushing Multi-positions ESD protection available Typical Applications Telecommunications
1/2" (12.7 mm) Conductive Plastic and Cermet Potentiometer
1/2" (12.7 mm) Conductive Plastic and Cermet Potentiometer FEATURES Robust construction High rotational life (50 000 cycles) Up to three sections PC support plates Rotary switches and solder lugs terminals
XA16ECO/B1PC1S XA16ECO/B4PC1S
XA16ECO/B1PC1S XA16ECO/B4PC1S B4PC1S B1PC1S - 14 1 Amp Single Pole (Single Throw) Switch XA Terminals Bent Extra Long Toward Switch PC Printed Circuit Terminals This image shows the XA terminals located
C&K ET Series Sealed Subminiature Rocker Switches
Sealed Subminiature Switches eatures/benefits Sealed against solder and cleaning process contaminants, bushing & case UL 94V-0 Small footprint saves space Typical Applications Telecommunications Instrumentation
TOCOS PANEL CONTROLS INDUSTRIAL APPLICATIONS
PANEL CONTROLS INDUSTRIAL APPLICATIONS Carbon Film Wirewound Cermet Long Life Carbon Film Attenuators SELECTION GUIDE www.tocos.com Carbon Panel Controls RV102 Series RV103 Series RV12 Series Resistance
SPDT DPDT 3PDT 4PDT SWITCHES TACT POS 1 POS 2 POS 3. Model No.
SCHEMATIC 3 2 1 Model No. SP-1 ON NONE ON SP-2 ON NONE (ON) SP-3 ON OFF ON SP-4 (ON) OFF (ON) SP-5 ON OFF (ON) Term. Comm. 2-3 OPEN 2-1 ( ) = Momentary 6 5 4 3 2 1 Model No. DP-1 ON NONE ON DP-2 ON NONE
7000 Series Miniature Rocker & Lever Handle Switches
Features/Benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoS compliant Typical Applications Telecommunications
8000 series. Momentary or alternate action pushbutton switches DISTINCTIVE FEATURES ELECTRICAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS
SW-8000-808 DISTINCTIVE FEATURES Momentary or alternate Bushing Ø 6.35 (/4) and Ø.9 (5/3) UL approved ELECTRICAL SPECIFICATIS Max. current/voltage rating with resistive load : - silver contacts : 4 A 30
Momentary or alternate action pushbutton switches. UL approved 3A 250VAC, 6A 125VAC. Availability : consult factory for details of approved models.
Distinctive features and specifications Bushing Ø 6,35 (1/4) and Ø 11,9 (15/32) UL approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts : 4A 30VDC - gold
Data Sheet for Precision Potentiometer
The RP22/23 potentiometers in 22 mm metal housing are suitable for applications where a accurate and compact sensor with high electrically effective rotation angle is required. Accurate wirewound potentiometer
(LRF) 4-Terminal Connection Kelvin Current Sensing Chips. Token Electronics Industry Co., Ltd. Version: July 12, Web:
Version: July 12, 2018 (LRF) 4-Terminal Connection Kelvin Current Sensing Chips Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: rfq@token.com.tw Taiwan: No.137, Sec. 1, Zhongxing Rd.,
E Series Sealed Miniature Toggle Switches
Sealed Miniature Switches eatures/benefits Sealed against solder and cleaning process contaminants UL 94V-0 Nylon case and bushing Multi-positions ESD protection available RoHS compliant models available
RoHS ON - OFF. ON - OFF (momentary ON) ON - OFF. (momentary OFF) ON - ON ON - ON. (momentary 1 side) ON - OFF - ON µ. (momentary 1 side)
900 Metal Lever Switches 6A 50Vac Metal lever switches Ratings up to 0A, 77V ac Single and double pole hoice of circuits including position and momentary 6.mm and solder terminals Guard option 6(4)A 50Vac
PC4G20BU. PC Printed Circuit Terminals
PC4G20BU PC Printed Circuit Terminals W Y X L A S E Mounting Height Mounting Diameter Spindle Diameter Spindle Length Initial Termination Wiper (or moving contact) termination End Termination Prefix (Potentiometer
(LRF) 4-Terminal Connection Kelvin Current Sensing Chips. Electronics Tech. Direct Electronics Industry Co., Ltd. Version: July 17, 2018
Version: July 17, 2018 Electronics Tech. (LRF) 4-Terminal Connection Kelvin Current Sensing Chips Web: www.direct-token.com Email: rfq@direct-token.com Direct Electronics Industry Co., Ltd. China: 12F,
DIM. A (+ 0,05 0,51) .437 ±.020 (11,10 ± 0,51) DIM. F ±.015 (0,38) INTEGRAL ASSEMBLY NUT, DO NOT REMOVE
Multi-Deck SERIES,, and " Diameter, Amp, Standard, Military SR0 FEATURES Rugged Construction Insures Switch Operation for the Life of Your Equipment Many Circuitry Options MIL Qualified Versions MIL-S-/0
General Information... Temperature/Resistance Table... Part Numbering Examples for RTD s. High Temperature MgO Elements (RA)...
Page General Information... Temperature/Resistance Table... Part Numbering Examples for RTD s High Temperature MgO Elements (RA).... Leadwire Style RTD s (RB).. Leadwire Style RTD s (RD, RE, RF, or RG
M x Series Valve Linkage Kits
Installation Instructions M9000-51x Issue Date 05/01/02 M9000-51x Series Valve Linkage Kits Installation Parts Included Quantity Description 1* Actuator Mounting Bracket 1* Adjustable Anti-Rotation Slider
1200 series. Momentary pushbutton switches - round plunger. Distinctive features and specifications. Butt action contacts, double break
Distinctive features and specifications Butt action contacts, double break NF (EN 61058-1), UL and CSA approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts
Damper Actuator Installation
FANs 268.1, 977, 1628.3 Installation Bulletin EPP-1000 Issue Date 0800 EPP-1000 Series Electro-Pneumatic Positioners A pplication The EPP-1000 is designed for applications where electronic control of pneumatic
ANR SPECIFICATIONS. MATERIALS RoHS COMPLIANT - E222871
Wide variety of applications from consumer electronics to commercial Standard epoxy sealed terminations Gold contacts available for low power applications Available support brackets for greater stability
Miniature Pneumatic Solenoid Valve
V Valve 15 mm Pneumatic Solenoid Valve Typical Applications Oxygen Conservers Flow control/shut-off valve Portable Medical Devices Product Specifications Mechanical Valve Type: /3 Port, Direct-acting poppet
SERIES. LED-Lit Push-Button Switches and Indicators. switches and indicators. SERIES 2 PRODUCT LINE-UP
LED-Lit Push-Button Switches and Indicators SERIES 2 LED-lit (DC and 24Vac) switches and indicators. You can build the product best suited to your specifications by combining standard parts Selection of
SPECIFICATIONS: MATERIALS: If your preferred product configuration is not shown, please contact our sales representative for custom design.
SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 50,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. initial @2-4VDC 00mA for both silver
E Series Sealed Miniature Rocker and Lever Handle Switches
Sealed Miniature and Lever Handle Switches Features/Benefits Sealed against solder and cleaning process contaminants ESD Resistance all actuator options, case & bushing UL 94V-0 RoHS compliant Typical
Product Range. Rocker & Paddle Switches. Rocker & Paddle Switches. Rocker & Paddle Switches
Product Range for Panel Mounting: F, TRD and Gemini Series for PCB Mounting: Gemini Series Main features: Sealed or unsealed versions Various switch functions Gold or silver contacts LED illumination available
Temperature Coefficient of Resistance Temperature Coefficient of Resistance, Tracking Maximum Operating Voltage Insulation Resistance
.220 Small Outline Dual-In-Line Thick Film Surface Mount Resistor Networks RoHS Compliant Electrical Standard Resistance Range, Ohms Standard Resistance Tolerance, at 25 C Operating Temperature Range Temperature
9 mm Multi-Ganged Potentiometer
9 mm Multi-Ganged Potentiometer FEATURES Conductive plastic element Ultra compact (extra miniature module size) Multiple assemblies (up to seven modules) Shaft and panel sealed option Center mechanical
9000 Series Power Rocker and Lever Handle Switches
Power and Lever Handle Switches Features/Benefits Thermoset UL 94V-0 housing Rugged construction Variety of actuator and termination options RoHS compliant Typical Applications Small equipment Shut-off
Momentary pushbutton switches - round plunger
1200 series Momentary pushbutton switches - round plunger Distinctive features and specifications Butt action contacts, double break NF (EN 61058-1), UL and CSA approved ELECTRICAL SPECIFICATIONS Max.
SERIES 16, 18, 26 & 19N MICROSWITCH RANGES
SERIES 16, 18, 26 & 19N MICROSWITCH RANGES SERIES 16, 26 & 18 - MICROSWITCH SERIES 16 & 26 FEATURES Form Z contacts to cover all switching requirements Snap action for positive switching Solder terminals
SERIES 100 SWITCHES TOGGLE SWITCHES - MINIATURE. Phone: Fax: SPECIFICATIONS MATERIALS
TACT SERIES 100 - MINIATURE SPECIFICATIONS Contact Rating: Life Expectancy: Contact Resistance: Insulation Resistance: Dielectric Strength: See contact material options 40,000 make-and-break cycles at
8500 Series Subminiature Pushbutton Switches
8500 Series Features/Benefits Pre-travel or over-travel models available Ratings up to 3 MPS Reliable contact design RoHS compliant Typical pplications Detection Telecommunications and networking equipment
MINIATURE POSITIVE ACTION SWITCHES MIL-S-8834 Miniature Positive Action Switches Solder Lug Terminals
MINIATURE POSITIVE ACTI SWITCHES FEATURES Sealed bushing Current rating versatility 1 and 2 pole circuitry Non-teasible mechanism for all but center "" circuits Dry circuit (logic level loads) to power
STAR DAMPERS ASTRAL ACTUATOR (DA SERIES)
STAR DAMPERS ASTRAL ACTUATOR (DA SERIES) An On/Off Motorized Damper Actuator. Star dampers are designed primarily for use on cool or warm air ducted systems. Star actuators are compatible and interchangeable
8000 series Momentary or alternate action pushbutton switches
Distinctive features and specifications ushing Ø 6,35 (1/4) and Ø 11,9 (15/32) UL approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts : 3A 250VAC - 6A
Distinctive Characteristics
Distinctive Characteristics Various cap styles and colors to meet differing application needs. Bright, full face illumination to distinctively indicate status. Rear panel threaded mounting or snap-in mounter
Cole s Series 3600 one inch diameter rotary switch is designed for
3600 series Cole s Series 3600 one inch diameter rotary switch is designed for instrumentation, industrial controls, medical equipment, military, aircraft, weapons, as well as ground support electronics
Solstice Electric Fryers SE Series Service Manual
Solstice Electric Fryers SE Series Service Manual L22-330 R1 (10/12) Notice In the event of problems or questions about your order, contact the Pitco Frialator factory at (603) 225-6684. In the event of
S E C Q - E - S T 1-2. Cap/ Sealing Hood (STD) 8.89 B solder lug Q (none) (none) Rubber Hood
T 8 0 1 3 - S E C Q - E - S 2 0 - T 1-2 Switch Function (SPDT) Actuator Bushing Termination Contact Switching Position Model No. S 10.41 E Epoxy Seal Vertical Support Bracket Cap/ Sealing Hood (STD) 8.89
Ball splines can be configured for an endless number of automated operations. Demystifying Ball Spline Specs
Ball splines can be configured for an endless number of automated operations. Demystifying Ball Spline Specs Place a recirculating-ball bushing on a shaft and what do you get? Frictionless movement of
Lighted Pushbutton Switch
Lighted Pushbutton Switch General Purpose and Micro-Voltage/Current Load Switch Requires only 22 mm mounting depth All LEDs, lamps, legends and pushbutton units replaceable without tools Oil-resistant
HOW TO ORDER SPECIFY AS SHOWN BELOW EXAMPLE #1
MERCURY TO METAL CONTACTORS AND RELAYS GLASS SEAL GUIDE RETAINER TEFLON GUIDE MAGNETIC SLEEVE BOBBIN TERMINAL WELD RING CERAMIC INSULATOR ELECTRODE METAL CAP DESCRIPTION MERCURY TO METAL CONTACTOR: The
5000 SERIES TOGGLE SWITCHES Distinctive features B
5000 SERES TOGGLE SWTCHES Distinctive features THE WDEST RANGE N MNATURE SWTCHES 7 7 actuators including toggles, paddle levers and locking levers in different lengths. 5 5 contact materials from dry circuit
SERIES 34A Miniature Toggle Switches
DIP Switches Toggle Switches Series A: Miniature Toggle Switches SERIES A Miniature Toggle Switches FEATURES Save Space and Weight,, PDT, and DPT Circuitry Choice of Actuators, Bushings and Terminations
2-Way & 3-Way Non Spring Return Characterized Ball Valves
VCB30 Series Revision Date June 6, 2014 2-Way & 3-Way Non Spring Return Characterized Ball Valves General The VCB30 Series electric rotary-motion actuatordriven characterized ball valves are designed specifically
AV series Anti-vandal and security pushbutton switches
Anti-vandal and security pushbutton switches Distinctive features Attractive, robust and durable Irremovable Anti-jamming construction : reduced travel to prevent insertion of foreign parts and mechanism
Toggle Switches. 214 Switches. Nylon and Metal switch variants. Multiple Lever Options. Ratings up to 20A, 250V ac - 277V ac
Toggle Switches Well known for their quality and reliability, Bulgin s toggle switches are cost effective solutions to many existing applications. These switches offer features at an attractive price point
C&K 8060 Series Alternate Action and Momentary Pushbutton Switches
lternate ction and Momentary Switches Specifications CONTCT RTING: Q contact material: 6 MPS @ 120 V C or 28 V DC; 3 MPS @ 250 V C. See page -53 for additional ratings. ELECTRICL LIFE: 50,000 make-and-break
2M Series Sub-Miniature Toggle Switches
M Series Sub-Miniature Toggle Switches SPECIFICATIS CTACT RATING: Dependent upon contact material See Page 8. MECHANICAL LIFE: 0,000 make-and-break cycles. CTACT RESISTANCE: 0 m max. initial @ -VDC 00mA