REFRIGERATION THERMOSTATS

Transcription

1 REFRIGERATION THERMOSTATS DANFOSS REFRIGERATION THERMOSTATS INTRODUCTION KP thermostats are temperature-controlled electrical switches. All KP thermostats have a single pole double throw (SPDT) changeover switch. The position of the switch depends on the thermostat setting and the bulb temperature. A KP thermostat can be directly connected to single-phase a.c. motors of up to about 2.7 hp, or installed in the control current circuit of d.c. motors and large a.c. motors. FEATURES Wide regulating range. Can be used for deep freeze, refrigeration and air conditioning systems. Welded bellows elements mean increased reliability. Small dimensions Easy to install in refrigerated counters or cold rooms. Ultra-short bounce times. Long operating life. Unnecessary cut-in and cut-out of control equipment is avoided. Standard versions with changeover switch. Possible to obtain opposite switch function or to connect a signal. Electrical connection at the front of the unit facilitates rack mounting. Saves space. Suitable for alternating and direct current. No spade or lug terminals required. Integral 1/2 NPSM swivel cable connector. Allows direct attachment of 1/2 in. male pipe thread connector. Extensive and wide range. APPROVALS UL listed, file E CSA certified, LR P636 P636C 463

2 REFRIGERATION THERMOSTATS DANFOSS REFRIGERATION THERMOSTATS ORDERING CHARGE Vapour* Adsorption TYPE BULB TYPE REGULATION RANGE DIFFERENTIAL t At Lowest Temperature Setting F At Highest Temperature Setting F RESET *Bulb must be installed in colder position than thermostat housing and capillary tube. Bulb can be placed warmer or colder than thermostat housing. **On manual minimum reset units the set value is equal to the cut-out value (lowest activating temperature). Reset is possible after a temperature rise of 5.4 F. Factory setting: Cut-In: 60 F Cut-Out: 25 F CAPILLARY TUBE LENGTH KP 61 B Auto L2002 KP 62 C Auto. 60L2015 KP 63 A Auto L2007 KP 69 B Auto L2009 KP 71 E Auto L2010 KP 71 E Fixed 5.4 Fixed 5.4 Man., Min.** L2011 KP 73 D Auto L2017 KP 73 E Auto L2029 KP 98 E 2 Oil: 30 to 90 HT: 210 to 350 Oil: fixed 22 HT: fixed 45 Oil: fixed 22 HT: fixed 45 Man., Max. in ft L2025 THEMOSTAT BULB TYPES A Straight capillary tube Sensing Length: 15 in. of 80 in. B Dia. 3/8 in. x 2-3/4 in. remote air coil C Dia. 1-9/16 in. x 1 in. air coil (integral with thermostat) D Dia. 3/8 in. x 2-3/4 in. double contact remote bulb NOTE: Cannot be used in sensor (bulb) pocket. E E1: Dia. 1/4 in. x 3-3/8 in. remote bulb E2: Dia. 3/8 in. x 4 in. remote bulb 464

3 TEMPERATURE & CONTROLS ALCO TF115 TEMPERATURE CONTROLS The TF115 Temperature Controls are designed to sense space or surface temperatures in cooling or heating applications for cycling and alarm applications. Maximum application flexibility is provided by using a heavy-duty 24 amp single pole double throw SPDT switch and temperature ranges and power elements designed for specific applications. P1024 PART NUMBER* RANGE IN F DIFFERENTIAL IN F SWITCH REMOTE COILED BULB VAPOR CHARGED TF115-S1 AA10 Low Temp -60 to +15 TF115-S2 AA10 3 to 30 SPDT Refrigerator/ -20 to +60 Freezer Control AIR COIL ROOM SENSING TF115-S2 AE00 Walk-in -20 to +60 Coolers/Freezers 3 to 30 SPDT TF115-S3 AE00 Ventilating/A.C./ Heat +15 to +95 WIDE RANGE BULB SENSING TF115-S4 AF10 Wide Range -20 to to 35 SPDT Temperature Control CAPILLARY & BULB 10 Capillary with 3/8 x 2 coiled bulb Air Coil for space temperature sensing 10 Capillary with 3/8 x 2-3/4 solid bulb REPLACES Ranco Penn White-Rodgers Honeywell O O O O O O O O O O F25-107** T4031A1008 A19BBC T6054A A19BAB-3 A19BAC-1 A19ABC-24 A19ZBC-2** T6054B T6031A1029 *The controls listed replace many other temperature controls than just those shown in this table. Limited Range check application. **Functional replacement. TF115 ELECTRICAL RATINGS MAXIMUM LOAD 120 VAC 240 VAC Full Load Amps 24 FLA 24 FLA Locked Rotor Amps 144 LRA 144 LRA Horsepower 2 HP 3 HP Pilot Duty 720 VA 720 VA Noninductive 24 amps 24 amps TF115 DIMENSIONAL DRAWINGS P1025 SETTINGS & ADJUSTMENTS: TF115/FF115/FF215 ADJUSTABLE RANGE & DIFFERENTIAL CONTROLS ADJUSTABLE RANGE FIXED DIFFERENTIAL CONTROLS OR HIGH SIDE DUAL P1026 Procedure 1. Adjust the Range Screw/Pointer to the desired High Event setting. 2. Adjust the Differential Screw to the desired differential. Low Event = High Event Differential Adjustment of the Range Screw changes both high and low events Adjustment of the Differential Screw changes the Low Event only. Procedure 1. Adjust the Range Screw to the desired High Event setting. Low Event = High Event Fixed Differential P1026A Adjustment of the Range Screw changes both the high and low events. 465

4 TEMPERATURE & CONTROLS RANCO LUBE OIL PROTECTION CONTROLS These lube oil protection controls guard pressure-lubricated refrigeration compressors against major damage due to loss of oil pressure. If adequate oil pressure is lost, the built-in S30 Time Delays Switch starts timing. If the oil pressure does not recover within the set period, the control circuit is opened, stopping the compressor. P1123 MODEL SELECTION CHART RANGE P.S.I.D. VOLTAGE A.C. TIME DELAY (Seconds) P30 36 Capillary With Flare Nut NOTE: The range is the difference between the crankcase pressure and the oil pump pressure that will energize the time delay switch and lead to shut down. The difference in oil pressure needs to rise 7 P.S.I. above the range to de-energize the time delay switch and prevent eventual shutdown. Male Flare Male Flare With 24 Ref. Hose 9 Fixed 120 RAN-P RAN-P RAN-P H 5 Fixed 60 RAN-P RAN-P RAN-P H 120 or to RAN-P RAN-P H Adjustable 90 RAN-P RANCO REFRIGERANT HOSE Refrigerant hose is a heavy duty hose designed for critical applications like commercial refrigeration. It is designed to resist breakage from compressor vibration. The refrigerant hose is made of teflon tubing, surrounded by a braided 304 stainless steel wire. P OVERALL HOSE LENGTH FITTINGS (1/4 SAE) RAN B18 18 RAN B24 24 RAN B36 36 Straight 7/16-20 Female Flare Connection RAN B48 48 RAN A18 18 RAN A24 24 RAN A36 36 RAN A48 48 One Straight And One 90 Elbow Both Ends Have 7/16-20 Female Flare Connection 466

5 TEMPERATURE & CONTROLS RANCO MINI CONTROLS LOW, HIGH AND FAN CYCLING CONTROLS Ranco Mini Pressure, fixed setting controls are used on refrigeration or air conditioning systems. P1125 P1126 MODEL SELECTION CHART APPLICATION Low Pressure Cut-Out Condenser Fan Cycling High Pressure Cut-Out High Pressure Manual Reset MP SETTINGS P.S.I.G. Cut-Out Cut-In RAN-MPL RAN-MPL RAN-MPL RAN-MPL RAN-MPL RAN-MPL RAN-MPL RAN-MPL RAN-MPF RAN-MPF RAN-MPF RAN-MPF RAN-MPF RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH RAN-MPH Lockout RAN-MPH Manual Reset LEADS, COLOR CODE Blue (Cut-Out On Pressure Drop) Black (Cut-Out On Pressure Rise) SPDT SETTING TOLERANCE PSI Cut-Out +/-5 Cut-In +/-6 (RAN-MPL-7003 is -12) Cut-Out +/-15 (RAN-MPF-7006 is +/-10) Cut-In +/-10 Cut-Out +/-10 Cut-In +/-15 (RAN-MPH-7101 is +/-20) Terminals 1 & 2 Open On Rise 1 & 4 Signal/Alarm; Close On Rise 467

6 TEMPERATURE & CONTROLS JOHNSON CONTROLS A19 REMOTE BULB CONTROL DESCRIPTION The A19 Series are single stage temperature controls that incorporate liquid filled sensing elements. P4411 SELECTION CHART *Replaces White-Rodgers Replaces White-Rodgers , -13; Ranco O , -1409, -1410, -1490, O60-110; Honeywell L6018C-1006, L6021A-1005, T , -1508, -1516, -1821, T4301A-1008, T6031A-1011, T6031A **Case-Compensated. Universal Replacement. SWITCH ACTION RANGE F ( C) DIFF F (C ) BULB AND CAPILLARY BULB WELL NO. (Order Separately) RANGE ADJUSTER MAX. BULB TEMP F ( C) Wide Range Adjustable Differential A19ABA-40C* SPST Open Low 30 to 100 ( 34 to 38) 3 to 12 (1.7 to 6.7) 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19ABC-4C SPDT 50 to 130 (10 to 55) 3-1/2 to 14 (1.9 to 8) 3/8 in. x 5 in., 8 ft Cap. WEL14A-603R Knob 170 (77) A19ABC-24C SPDT 30 to 100 ( 34 to 38) 3 to 12 (1.7 to 6.7) 3/8 in. x 4 in., 8 ft Cap. WEL14A-602R Convertible 140 (60) A19ABC-36C SPDT 30 to 100 ( 34 to 38) 3 to 12 (1.7 to 6.7) 3/8 in. x 4 in., 20 ft Cap. WEL14A-602R Convertible 140 (60) A19ABC-37C SPDT 30 to 100 ( 34 to 38) 3 to 12 (1.7 to 6.7) 3/8 in. x 4 in., 10 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19ABC-74C SPDT 30 to 100 ( 34 to 38) 3 to 12 (1.7 to 6.7) 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) Fixed Differential A19AAF-12C SPDT 25 to 225 ( 4 to 107) 3-1/2 (1.9) 3/8 in. x 3 in., 10 ft Cap. WEL14A-602R Screwdriver Slot 275 (135) CASE COMPENSATED FIXED DIFFERENTIAL A19AAC-4C SPDT 0 to 80 ( 18 to 27) 5 (2.8) 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19AAD-12C SPST Open Low 30 to 50 ( 34 to 10) 2-1/2 (1.4) 3/8 in. x 4 in., 7 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) Close Differential A19AAD-5C** SPST Open Low 30 to 50 ( 1 to 10) (Bulk Milk Cooler) 2-1/2 (1.4) 3/8 in. x 2-5/8 in., 6 ft Cap. WEL16A-601R Screwdriver Slot 190 (88) A19AAF-20C SPDT 30 to 100 ( 34 to 38) 2-1/2 (1.4) 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19AAF-21C SPDT 40 to 90 (4 to 32) 1-1/2 (0.8) 3/8 in. x 5-3/4 in., 6 ft Cap. WEL14A-603R Screwdriver Slot 140 (60) Manual Reset A19ACA-14C SPST Open Low 30 to 100 ( 34 to 38) Manual Reset 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19ACA-15C SPST Open Low 30 to 100 ( 34 to 38) Manual Reset 3/8 in. x 4 in., 10 ft Cap. WEL14A-602R Screwdriver Slot 140 (60) A19ADB-1C SPST Open High 100 to 240 (38 to 116) Manual Reset 3/8 in. x 3-1/2 in., 6 ft Cap. WEL14A-602R Knob 290 (143) A19ADN-1C SPST Open HIgh 100 to 240 (38 to 116) Manual Reset 3/8 in. x 4 in., 6 ft Cap. WEL14A-602R Screwdriver Slot 290 (143) 468

7 TEMPERATURE & CONTROLS JOHNSON CONTROLS A419 ELECTRONIC TEMPERATURE CONTROL DESCRIPTION The A419 Series control is a line voltage, single-stage, electronic temperature control with a Single-Pole, Double-Throw (SPDT) output relay. It has heating or cooling modes of operation with an adjustable set point and differential, a lockable keypad, an adjustable anti-short cycle delay, and binary input for temperature offset. The A419 combines remote sensing capability and interchangeable sensors with electronic accuracy, all in a NEMA 1 high-impact plastic enclosure that is suitable for surface-mounting or DIN-rail mounting. P4412 APPLICATIONS The A419 can be used to control a wide variety of single-stage refrigeration or HVAC equipment. Typical applications include: freezer control in convenience stores reach-in coolers supermarket display cases for produce or meats restaurant or convenience store walk-in coolers boiler control compressor lockout (disables the compressor when temperature exceeds limits) condenser fan cycling pump control for cooling towers space and return-air temperature SELECTION CHART DESCRIPTION A419ABC-1C A419 Electronic Temperature Control with Display and Sensor (120/240 VAC model) A419GBF-1C A419 Electronic Temperature Control with Display and Sensor (24 VAC model) A99BB-200C PTC Sensor with 6.5 ft (1.98 m) Leads BKT287-1R 35 x 7.5 mm, m (12 in.) long DIN Rail BKT287-2R 35 x 7.5 mm, m (36 in.) long DIN Rail PLT344-1R Two End Clamps, for DIN Rail Mounting CLK Day Programmable Digital Clock; Electronic Switch Output WEL11A-601R Immersion Well (Use with Thermal Compound) JOHNSON CONTROLS A319 ELECTRONIC TEMPERATURE CONTROL DESCRIPTION The A319 Series is a line voltage, single-stage electronic temperature control with Single-Pole, Double-Throw (SPDT) relay output and LED indication. The A319 features heating or cooling modes of operation, adjustable cut-in, adjustable differential, and an interchangeable temperature sensor. The A319 couples electronic accuracy with remote sensing capability in a NEMA 1 high-impact plastic enclosure suitable for surface or DIN rail mounting. P4415 SELECTION CHART ITEM DESCRIPTION A319 Temperature Control with Sensor A319ABC Cut-in Range: 100 to 220 F (38 to 105 C) Differential: 1 to 30 F (0.5 to 17 C) Sensor Lead Length: 8 ft (2.4 m) A319 Temperature Control With Sensor A319ABC Cut-in Range: 20 to 100 F ( 30 to 38 C) Differential: 1 to 30 F (0.5 to 17 C) Sensor Lead Length: 8 ft (2.4 m) A319 Temperature Control With Sensor A319ABC Cut-in Range: 25 to 50 F ( 32.5 to 10 C) Differential: 1 to 15 F (0.5 to 8 C) Sensor Lead Length: 8 ft (2.4 m) A319 Temperature Control Without Sensor A319ABC Cut-in Range: 100 to 220 F (38 to 105 C) Differential: 1 to 30 F (0.5 to 17 C) A319 Temperature Control Without Sensor A319ABC Cut-in Range: 20 to 100 F ( 30 to 38 C) Differential: 1 to 30 F (0.5 to 17 C) A319 Temperature Control Without Sensor A319ABC Cut-in Range: 25 to 50 F ( 32.5 to 10 C) Differential: 1 to 15 F (0.5 to 8 C) 469

8 TEMPERATURE & CONTROLS JOHNSON CONTROLS A28 SERIES TWO-STAGE FLANGE MOUNTED DUCT THERMOSTAT DESCRIPTION The A28AK is a two-stage temperature control with special air coil sensing element and adjustable mounting flange. P4408 SELECTION CHART DIFFERENTIAL F (C ) MAXIMUM ALLOWABLE NUMBER OF SWITCH RANGE FIXED TEMPERATURE AT BULB STAGES ACTION F ( C) Each Stage Between Stage F ( C) A28AK-1C 2 2-SPDT Switches 30 to 110 ( 1 to 43) 2 (1.1) 3 (1.7) 140 (60) A28AK-2C 2 2-SPDT Switches 60 to 130 (16 to 54) 2 (1.1) 3 (1.7) 200 (93) JOHNSON CONTROLS P70 SERIES SINGLE-POLE DUAL CONTROL DESCRIPTION This P70 Series of dual pressure controls employs a SPST switch, that is opened when either high pressure or low pressure beyond the control settings is sensed at the control s two bellows sensing elements. The load-carrying contacts provide direct control of AC motors within the control s rating. These controls provide close high-open low (low pressure) or open high-close low (high pressure) contact action. SELECTION CHART P4410 P70LB-6C P70MA-18C P70LB-1C P70MA-1C P70NA-1C P70SA-1C P70LA-2C P70MA-2C SWITCH ACTION SPST SPST Two Independent SPDT Switches SPST LOW psig (kpa) HIGH psig (kpa) Range Diff Range Diff (Non-Adj) MICRO-SET FOR R-12, R-22, R-134a, R-500, R-502 (R) 65 psi at < 300 psig 75 psi at psig 95 psi at > 400 psig 12 in. to 80 ( 41 to 552) 20 in. to 100 ( 68 to 690) 12 in. to 80 ( 41 to 552) 20 in. to 100 ( 68 to 690) Min 5 (34) Max 35 (241) 100 to 500 (690 to 3447) Lockout (Requires Manual Reset) ALL RANGE FOR R-12, R-22, R-134a, R-500, R-502 (R) 65 psi < 300 psig 75 psi psig 95 psi > 400 psig Min 7 (48) Max 50 (345) 100 to 500 (690 to 3447) Lockout (Manual Reset) Min 5 (34) Max 35 (241) Min 7 (48) Max 50 (345) 100 to 500 (690 to 3445) CONNECTOR 36 in. Cap. with 1/4 in. Flare Nut 36 in. Cap. with 1/4 in. Flare Nut 36 in. Cap. with 1/4 in. Flare Nut Lockout 36 in. Cap. with (Requires Manual Reset) 1/4 in. Flare Nut Lockout 36 in. Cap. with (Requires Manual Reset) 1/4 in. Flare Nut Switchable Between 36 in. Cap. with Manual and Automatic 1/4 in. Flare Nut Reset FOR AMMONIA 65 psi < 300 psig 1/4 in. Female 75 psi psig NPT Conn. 95 psi > 400 psig 100 to 500 (690 to 3445) Lockout (Requires Manual Reset) 1/4 in. Female NPT Conn. LMITED KNOB ADJ. Cut-out None Cut-out None None None MAXIMUM OVER psig (kpa) 325 Low 525 High (2241 Low) (3620 High) 325 Low 525 High (2241 Low) (3620 High) 525 Low 525 High 325 Low 525 High (2241 Low) (3620 High) Universal Replacement. 470

9 TEMPERATURE & CONTROLS JOHNSON CONTROLS P72 SERIES TWO-POLE LOW- CONTROL DESCRIPTION The P72 Series of controls employs a set of DPST contacts that are opened and closed by the pressure actuated bellows. The heavy duty load-carrying contacts provide direct control of motors having integral line-interrupting overload protectors up to three horsepower, 240 volt, single phase. Starter is unnecessary. Primarily used on air-conditioning and refrigeration applications but also used to control air, water, and lube oil pressure. SELECTION CHART P72AA-1C SWITCH ACTION DPST: Close High, Open Low RANGE psig (kpa) 20 in. to 100 psi ( 68 to 690) DIFFERENTIAL (psi) Min 7 (41) Max 50 (345) CONNECTOR 36 in. Cap. with 1/4 in. flare Nut KNOB ADJUSTMENT MAX BELLOWS OVER psig (kpa) None 325 (2241) P1019 JOHNSON CONTROLS P70 SERIES SINGLE-POLE LOW- CONTROL DESCRIPTION This P70 Series of controls employs a set of switch contacts that are opened and closed by the movement of pressure actuated bellows. The load-carrying contacts provide direct control of AC motors within the control rating. Note the electrical rating chart for specific models. These controls are available with either close high-open low, open high-close low, or SPDT contact action. SELECTION CHART SWITCH ACTION RANGE psig (kpa) DIFFERENTIAL psi (kpa) CONNECTOR LIMITED KNOB ADJUSTMENT MAX BELLOWS OVERRUN psig (kpa) MICRO-SET FOR R-12, R-22, R-134a, R-500, R-502 (R) P70AB-12C Close High Open Low 12 in. to 80 ( 40 to 551) Min 5 (34) Max 35 (241) 36 in. Cap. with 1/4 in. Flare Nut Cut-out* 525 (3620) ALL RANGE FOR R-12, R-22, R-134a, R-500, R-502 (R) P70AA-1C 36 in. Cap with 1/4 in. Flare Nut None P70AB-1C Close High Min 7 (48) 1/4 in. Male Flared Conn. Open Low Cut-out* P70AB-2C 20 in. to 100 Max 50 (345) 36 in. Cap. with ( 68 to 690) 1/4 in. Flare Nut Cut-out* 325 (2241) P70CA-1C Open High 36 in. Cap. with Close Low 1/4 in. Flare Nut None P70EA-10C SPDT 5 (34) Fixed 1/4 in. Male Flared Conn. None FOR AMMONIA P70AA-5C Close High Open Low 20 in. to 100 Min 7 (48) 1/4 in. Female P70CA-4C Open High ( 68 to 690) Max 50 (345) NPT Close Low None 325 (2241) P1019 *Adjusting knob supplied on differential (cut-out setting) to limit adjustments to 5 psi (34 kpa) above or below normal setting. Universal Replacement. SPST ELECTRICAL RATINGS (P70A and P70C Models) STANDARD SINGLE-PHASE RATINGS HERMETIC COMPRESSOR SINGLE-PHASE RATINGS 120 VAC 208 VAC 240 VAC 208/240 VAC Motor Horsepower Motor Full-Load Amp Motor Locked Rotor Amp Non-Inductive Amp Pilot Duty 125 VA at 120 to 600 VAC; 57.5 VA at 120 to 300 VDC SPDT ELECTRICAL RATINGS (P70E Models) STANDARD SINGLE-PHASE RATINGS 120 VAC 208 VAC 240 VAC Motor Full-Load Amp Motor Locked Rotor Amp Non-Inductive Amp Pilot Duty 125 VA at 120 to 600 VAC 471

10 TEMPERATURE & CONTROLS JOHNSON CONTROLS V46 SERIES ACTUATED WATER REGULATING VALVE DESCRIPTION The V46 is a pressure actuated, modulating valve that is suitable for use either on closed or open systems. Direct acting valves open on pressure increase. This type of valve is primarily used to regulate the flow of water or glycol to a water cooled condenser on a refrigeration system. Reverse acting valves open on pressure decrease and are generally used in parallel with a direct-acting valve or for bypass operation. P4409 SELECTION CHART PIPE SIZE (in.) INLET AND OUTLET OPENING POINT RANGE psig (kpa) ELEMENT STYLE SEAT REPAIR KIT REPLACEMENT POWER ELEMENTS COMMERCIAL TYPE, STANDARD FLOW NON-CORROSIVE REFRIGERANTS (R) V46AA-1C 3/8 NPT STT14A-600R SEP91A-600R and SEC37A-601R V46AB-1C 1/2 NPT STT15A-602R SEP91A-602R and SEC37A-602R V46AC-1C 3/4 NPT Threaded 30 in. Capillary 70 to 260 STT16A-601R SEP91A-601R and SEC37A-602R 1/4 in. Flare Nut V46AD-1C 1 NPT (483 to 1793) (Style 45) STT17A-609R V46AE-1C 1-1/4 NPT SEP91A-603R and SEC37A-600R STT17A-610R V46AR-1C 1-1/2 70 to 170 V46AS-1C 2 SEP81A-602R (483 to 1172) STT18A-600R 160 to 260 V46AS-2C 2 4 Hole SEP81A-601R (1103 to 1793) ASME Flange 1/4 in. Male Flare Fitting 70 to 170 (Style 5) V46AT-1C 2-1/2 SEP81A-602R (483 to 1172) STT18A-601R 160 to 260 V46AT-2C 2-1/2 SEP81A-601R (1103 to 1793) 472

11 CONTROLS ALCO FF115 SINGLE LOW CONTROLS The FF115 Low Pressure Controls are designed to sense the suction pressure in refrigeration systems for cycling, limit and alarm applications. Maximum application flexibility and accuracy are assured by using a heavy-duty 24 amp single pole double throw (SPDT) switch and customized pressure ranges for precise sensing. P1019 FF115 ELECTRICAL RATINGS MAXIMUM LOAD 120 VAC 240 VAC Full Load Amps 24 FLA 24 FLA Locked Rotor Amps 144 LRA 144 LRA Horsepower 2 HP 3 HP Pilot Duty 720 VA 720 VA Noninductive 24 amps 24 amps PART NUMBER RANGE IN PSIG DIFFERENTIAL RANGE IN PSI FF-115-S1-BAK 24 to 42 3 to 30 FF-115-S3-BAK FF-115-S3-BAA 15 to to 70 SWITCH ACTION SPDT Auto Reset CONNECTION 36 Capillary with 1/4 Flare Nut 1/4 SAE Male Flare REPLACES Penn Copeland Ranco P70AB-12* P70AB-2 P70AB-12 P70CA-1 P70AB-1 P170AB-2,-12* P170CA O O O O O O O O *Controls have an extended range. For applications where the condensing unit/control is exposed to temperatures below 20 F, 1/4 lines are recommended. ALCO FF115 SINGLE HIGH- CONTROLS The FF115 High Pressure Controls are designed to sense the high side pressure in refrigeration systems for high pressure limit, alarm and condenser fan control. Maximum application flexibility is assured by using a heavy-duty 24 amp single pole double throw (SPDT) switch and wide range pressure setting capability. FF115 DIMENSIONAL DRAWINGS P1020 PART NUMBER** RANGE IN PSIG DIFFERENTIAL RANGE IN PSI FF-115-S4-BAK 15 to to 145 FF-115-S5-BAK FF-115-S5-BAA FF-115-S5-BRK FF-115-S5-BRA 90 to to PSI fixed SWITCH ACTION SPDT Auto Reset SPDT Manual Reset Trips on pressure rise CONNECTION 36 Capillary with 1/4 Flare Nut 1/4 SAE Male Flare 36 Capillary with 1/4 Flare Nut 1/4 SAE Male Flare REPLACES Penn Copeland Ranco P70AA P70AA-118 P70CA-3 P70CA-2 P170AA-118 P170CA-3 P70DA-1 P70KA-1* O O O O O O O O O O P170DA-1 O *FF115-S5-BRK has common power feed for limit and alarm function. 48 capillary. **Limited to stock on hand. 473

12 CONTROLS ALCO PS1 SERIES SINGLE CONTROLS PS1 Single Pressure Controls are designed for use on high and low pressure applications in refrigeration and heat pump systems. By operating a set of electrical contacts, a pressure is kept inside a certain limit. FEATURES Adjustable pressures and differentials. Narrow adjustable differential depending on model. Range and differential pointer in units bar and psig. Range and differential individually lockable by wire seal. High rated SPDT contacts for all versions. Captive terminal and cover screws. Manual toggle for system checkout and override. Factory installed wire bridge for reduced installation effort. SPECIFICATIONS SPDT switch rated for 120 VAC/240 VAC at 24 FLA and 144 LRA. Agency approvals include: UL/CUL file #E85974, VDE 0631/0660, TUV, CE 73/23/EWG, CE 93/68/EWG. Low pressure and high pressure versions available with TUV approval according to EN (supersedes DIN 32733) to meet requirements of DIN 8901 and EN378 (supercedes DIN 8975). FF115 REPLACEMENT OPTIONS Different pressure connections. Automatic and manual reset versions. Factory set to customer specifications. Different types of mounting brackets. NOMENCLATURE - EXAMPLE PS1-A5K PS1 A 5 K Product Name Function Pressure Range Pressure Connector Type PS1 = Adjustable single Pressure Control PSA = Customer specials A = Pressure control, automatic reset, internal range & differential adjustments B = Pressure cut out, external manual reset, DIN/TUV approved, internal range and differential adjustments*, R = Pressure cut out, external manual reset, internal range and differential adjustments*, S = Safety pressure cut out, internal manual reset, DIN/TUV approved, internal range & differential adjustments*, U = Convertible from R to A W = Pressure control, automatic reset, DIN/TUV approved, internal range and differential adjustments X = Pressure control, automatic reset, external range and differential adjustments Y = Pressure cut out, external manual reset, external range and differential adjustments *Function types B, R, S in combination with Pressure Range 1 or 3 have a low pressure manual reset function. (15 psi differential) Function types B, R, S in combination with Pressure Range 4 or 5 have a high pressure manual reset function. (60 psi diff.) 1 = 24 Hg to 42 psi (-0.75 to 3 bar) 2 = 26 Hg to 21 psi (-0.8 to 1.5 bar) 3 = 15 Hg to 100 psi (-0.5 to 7 bar) 4 = 15 to 290 psi (1 to 20 bar) 5 = 90 to 450 psi (6 to 31 bar) A = 7/16-20 UNF male for 1/4 SAE male flare C = R 1/4 stainless steel with steel bellows F = 1/4-18 NPTF stainless steel with steel bellows K* = 7/16-20 UNF flare nut with 1 meter (3 ft) cap tube L = 1/4 ODF solder with 1 meter (3 ft) cap tube R = R 1/4 U = 6 mm ODF solder, 80 mm tube length X = 1/4 ODF solder, 80 mm tube length *Controls with housing variant X/Y have extended copper ends, without Schrader valve depressor. All other housing variants have schrader valve depressor and brass end fitting with copper gasket. 474

13 CONTROLS ALCO PS1 SERIES SINGLE CONTROLS ALCO U.S. PCN Standard Product Offering. *Product Code Number. ALCO EUROPE PCN ADJUSTMENT RANGE Upper Setpoint Diff. Setpoint FACTORY SETTIG CONNECTION LOW CONTROLS TPC-PS1-X1K Hg to 42 (-.75 to 3) 4 to 29 (.25 to 2) 7/15 (.5/1) PS1-A3A /16-20 UNF TPC-PS1-X3A /16-20 UNF, 1/4 SAE male PS1-A3K Hg to to 73 50/65 TPC-PS1-X3K ( ) ( ) (3.5/4.5) PS1-A3L Capillary/solder PS1-A3U Solder 6 mm PS1-A3X Solder tube 1/4 PS1-R3A External 7/16-20 UNF PS1-R3K Manual Reset 15 Hg to 100 PS1-R3L Low Pressure 50 (3.5) Capillary/solder ( ) PS1-R3U psi Solder 6 mm PS1-R3X (1 bar) fixed Solder tube 1/4 HIGH CONTROLS TPC-PS1-X4K to 290 (1 to 20) 15 to 100 (1 to 7) 145/115 (10/8) PS1-A5A /290 (16/20) 7/16-20 UNF TPC-PS1-X5A /280 (10/19) 7/16-20 UNF PS1-A5K to to 217 TPC-PS1-X5K ( ) ( ) 230/290 PS1-A5L (16/20) Capillary/solder PS1-A5U Solder 6 mm PS1-A5X (20) Solder tube 1/4 PS1-R5A (20) 7/16-20 UNF TPC-PS1-Y5A Ext. Manual Reset 390 (27) 7/16-20 UNF, 1/4 SAE male PS1-R5K to 450 High Pressure TPC-PS1-Y5K ( ) 60 psi PS1-R5L (4 bar) fixed 290 (20) Capillary/solder PS1-R5U Solder 6 mm PS1-R5X Solder tube 1/4 LIMITER FOR LOW PROTECTION PS1-W3A /16-20 UNF PS1-W3K Hg to to 73 50/65 PS1-W3L Capillary/solder ( ) ( ) (3.5/4.5) PS1-W3U Solder 6 mm PS1-W3X Solder tube 1/4 CUT OUT FOR LOW PROTECTION PS1-B3A /16-20 UNF PS1-B3K Ext. Manual Reset 15 Hg to 100 Low Pressure 65 PS1-B3L Capillary/solder ( ) 15 psi (4.5) PS1-B3U (1 bar) fixed Solder 6 mm PS1-B3X Solder tube 1/4 LIMITER FOR HIGH PROTECTION PS1-W5A /16-20 UNF PS1-W5K to to /290 PS1-W5L Capillary/solder ( ) ( ) (16/20) PS1-W5U Solder 6 mm PS1-W5X Solder tube 1/4 475

14 CONTROLS ALCO PS1 SERIES SINGLE CONTROLS ORDERING INFORMATION FOR PS1 SINGLE CONTROLS Standard Product Offering. *Product Code Number. ALCO U.S. PCN ALCO EUROPE PCN Upper Setpoint ADJUSTMENT RANGE Diff. Setpoint FACTORY SETTING CONNECTION CUT OUT FOR HIGH PROTECTION PS1-B5A /16-20 UNF PS1-B5K Ext. Manual Reset PS1-B5L to 450 ( ) High Pressure 60 psi 290 (20) Capillary/solder PS1-B5U (4 bar) fixed Solder 6 mm PS1-B5X Solder tube 1/4 SAFETY CUT OUT FOF HIGH PROTECTION PS1-S5A /16-20 UNF PS1-S5K Int. Manual Reset 90 to 450 PS1-S5L ( ) High Pressure 304 (21) Capillary/solder PS1-S5U psi (4 bar) fixed Solder 6 mm PS1-S5X Solder tube 1/4 PS1 DIMENSIONAL DIAGRAM DIMENSIONS SHOWN ARE IN INCHES. OLD TO NEW CROSS REFERENCE (TF115 TO TS1) REPLACES THE COMPETITION OLD MODEL OLD PCN NEW MODEL NEW PCN COPELAND* RANCO PENN DANFOSS SAGINOMIYA O FF115-S1-BAK PS1-X1K 7/ P70AB CP1A-1K O O FF115-S4-BAK PS1-X4K 115/ P70AA-2 O FF115-S3-BAK PS1-X3K 50/ FF115-S5-BAK PS1-X5K 230/ CP1A3K CP1A-5K O O O O , O O16-108, O FF115-S5-BRK PS1-Y5K 230/ O FF115-S3-BAA PS1-X3A 50/ CP1A-3A FF115-S5-BAA PS1-X5A 140/ CP1A-5A O , O O , O O O , O O16-503, O O FF115-S5-BRA PS1-Y5A 330/ O16-209, O PS1-U5A 385 PS1-U5K CP1U-5A 985-CP1U-5K P70AB-12 P70AB-2 P70CA-2 P70AA-118 P70CA-3 P70DA-1 P70KA-1 P170AB-12 P170AB-2 P170AA-118 P170CA-3 P77AAA-9350 P77AAA-9370 P170DA-1 P77BEA-9350 P77BEA-9370 *The Alco control may be used with bracket (PCN ) to allow placement of the Copeland control with the same mounting configuration. KP KP KP SNS-C106X SNS-C130X SNS-C135X 476

15 CONTROLS ALCO PS1 SERIES SINGLE CONTROLS PS1 PARTS/ACCESSORIES UNIVERSAL ANGLE BRACKET Alco U.S. PCN #097064, KB Alco Europe PCN # ANGLED MOUNTING BRACKET Alco U.S. PCN #097215, KB Alco Europe PCN # KNOB AND LOCK PLATE KIT Alco U.S. PCN #097061, KB Alco Europe PCN # MOUNTING BRACKET Z TYPE Alco U.S. PCN #097063, KB Alco Europe PCN # Kit consists of adjustment knob, lockplate (2), pan-head screw (1) and fillister head screw with lock-wire hole (2). 477

16 CONTROLS ALCO FF215 DUAL CONTROLS FF215 ELECTRICAL RATINGS P1021 MAXIMUM LOAD 120 VAC 240 VAC Full Load Amps 24 FLA 24 FLA Locked Rotor Amps 144 LRA 144 LRA Horsepower 2 HP 3 HP Pilot Duty 720 VA 720 VA Noninductive 24 amps 24 amps PART NUMBER** LOW LO PRESS. DIFF. RANGE IN PSIG RANGE IN PSI FF-215-S9-BAUK 24 to 42 3 to 30 FF-215-S7-BAUK 15 to to 70 FF-215-S7-BAUA HIGH RANGE IN PSIG HI PRESS. DIFF. RANGE IN PSI 90 to fixed SWITCH ACTION LP SPDT Auto Reset HP SPDT Convertible User Selects Auto or Manual Reset CONNECTION (2) 48 Capillary with 1/4 Flare Nut 1/4 SAE Male Flare PART NUMBER FF-215-S9-BAUK REPLACES ALCO REPLACES PENN COPELAND RANCO PART NUMBER PENN COPELAND RANCO FF215-S7 BAUK P70LB-1, O P70LB-6* O P70MA-18* O O O O FF215-S7 BAUA P170LB-1 P170MA-1 O *Controls have an extended range. For applications where the condensing unit/control is exposed to temperatures below 20 F, 1/4 lines are recommended. **Limited to stock on hand. FF215 DIMENSIONAL DRAWINGS P

17 CONTROLS ALCO PS2 SERIES DUAL CONTROLS PS2 Dual Pressure Controls are designed for use on high and low pressure applications in refrigeration and heat pump systems. By operating a set of electrical contacts, a pressure is kept inside certain limits. FEATURES Adjustable pressures and differentials. Narrow adjustable differential depending on model. Range and differential pointer in units bar and psig. Range and differential individually lockable by wire seal. High rated SPDT contacts for all versions. Captive terminal and cover screws. Manual toggle for system checkout and override. Factory-installed wire bridge for reduced installation effort. NOMENCLATURE Example PS2-G8A OPTIONS Different pressure connections. Automatic and manual reset versions. Factory set to customer specification. Different types of mounting brackets. SPECIFICATIONS SPDT switch rated for 120 VAC/240 VAC at 24 FLA and 144 LRA. Agency approvals include: UL/CUL file #E85974, VDE 0631/0660, TÜV, CE 73/23/EWG, CE 93/68/EWG. Low pressure and high pressure versions available with TÜV approval according to DIN to meet requirements of DIN 8901and DIN FF215 REPLACEMENT PS2 G 8 A Product Name PS2 = Adjustable Dual Pressostat PSB = Customer Special Version Function A =Both sides: Pressure controls, automatic reset, internal range and differential adjustments B =Both sides: Pressure cut out, external manual reset, DIN/TÜV approved, internal range and differential adjustments C =Left side: Pressure control, automatic reset, DIN/TÜV approved, internal range and differential adjustments. Right side: Safety cut out, external manual reset, DIN/TÜV approved, internal range and differential adjustments. G = Left side: Pressure control, automatic reset, DIN/TÜV approved, internal range and differential adjustments. Right side: Safety limiter, internal manual reset, DIN/TÜV approved, internal range and differential adjustments. L =Left side: Pressure control, automatic reset, internal range and differential adjustments. Right side: Pressure cut out, external manual reset, internal range and differential adjustments. M = Left side: Pressure control, automatic reset, internal range and differential adjustments. Right side: Convertible reset from R to A, internal range and differential adjustments. R =Both sides: Pressure cut out, external manual reset, internal range and differential adjustments. S =Both sides: Pressure safety cut out, internal manual reset, DIN/TÜV approved, internal range and differential adjustments. T =Left side: Pressure control, automatic reset, DIN/TÜV approved, internal range and differential adjustments. Right side: Safety limiter, internal manual reset, DIN/TÜV approved, internal range and differential adjustments. U =Both sides: Convertible from R to A. W = Both sides: Pressure control, automatic reset, TÜV approved, internal range and differential adjustments. X =Both sides: Pressure controls, automatic reset, external range and differential adjustments. Y =Left side: Pressure control, automatic reset, external range and differential adjustments. Right side: Convertible from external manual reset to automatic reset, external range and differential adjustments. Z =Both sides: Convertible from external manual reset to automatic reset, external range and differential adjustments. LOW MANUAL RESET: Cut outs with manual reset function and in combination with the low pressure side of Pressure Ranges 7 and 9 have a low pressure manual reset function (15 psi differential). HIGH MANUAL RESET: Cut outs with manual reset function and in combination with the high pressure side of Pressure Ranges 7 and 9 have a high pressure manual reset function (60 psi differential). Pressure Ranges 7 = Left side: 15 Hg to 100 psi (-0.5 to 7 bar) Right side: 90 to 450 psi (6 to 31 bar) 8 = Left side: 90 to 450 psi (6 to 31 bar) Right side: 90 to 450 psi (6 to 31 bar) 9 = Left side: 24 Hg to 45 psi (-0.75 to 3 bar) Right side: 90 to 450 psi (6 to 31 bar) Pressure Connector Type A = 7/16-20 UNF male for 1/4 SAE flare fitting C = R 1/4 stainless steel with steel bellows F = 1/4-18 NPTF stainless steel with steel bellows K* = 7/16-20 UNF flare nut with 1 meter (3 ft) cap tube L = 1/4 ODM solder with 1 meter (3 ft) cap tube R = R 1/4 U = 6 mm ODF solder, 80 mm tube length X = 1/4 ODF solder, 80 mm tube length *Controls with housing variants X/Y/Z have extended copper ends, without schrader valve depressor and brass end fitting with copper gasket 479

18 CONTROLS ALCO PS2 SERIES DUAL CONTROLS ORDERING INFORMATION FOR PS2 DUAL CONTROLS ALCO U.S. PCN ALCO EUROPE PCN Standard Product Offering. *Product Code Number. Upper Setpoint Left Right ADJUSTMENT RANGE Differential Left Right FACTORY SETTING Left Right CONNECTION COMBINED LOW AND HIGH CONTROLS TPC-PS2-A7A /16-20 UNF TPC-PS2-A7K Hg to to to to /65 230/290 TPC-PS2-A7L Capillary/solder ( ) (6...31) ( ) (2...5) (3.5/4.5) (16/20) PS2-A7U Solder 6 mm PS2-A7X Solder tube 1/4 TPC-PS2-L7A /16-20 UNF PS2-L7K External Manual Reset 15 Hg to to to 72 50/ TPC-PS2-L7L High Press. Capillary/solder ( ) (6...31) ( ) (3.5/4.5) (20) PS2-L7U (4) fixed Solder 6 mm PS2-L7X Solder tube 1/4 PS2-R7A /16-20 UNF PS2-R7K External Manual Reset External Manual Reset 15 Hg to to PS2-R7L Low Press. High Press. Capillary/solder ( ) (6...31) (3.5) (20) PS2-R7U (1) fixed 60 (4) fixed Solder 6 mm PS2-R7X Solder tube 1/4 COMBINED LIMITER FOR LOW /HIGH PROTECTION PS2-W7A /16-20 UNF PS2-W7K Hg to to to to /65 230/290 PS2-W7L Capillary/solder ( ) (6...31) ( ) (2...5) (3.5/4.5) (16/20) PS2-W7U Solder 6 mm PS2-W7X Solder tube 1/4 COMBINED LIMITER/ CUT OUT FOR LOW /HIGH PROTECTION PS2-C7A /16-20 UNF PS2-C7K External Manual Reset PS2-C7L High Press. Capillary/solder 15 Hg to to to 72 50/65 PS2-C7U (4) fixed Solder 6 mm ( ) (6...31) ( ) (3.5/4.5) 290 PS2-C7X Solder tube 1/4" (20) TPC-PS2-Y7A /16-20 UN TPC-PS2-Y7K Convertible Auto/Manual TPC-PS2-Y9K Hg to 45 ( ) 90 to 450 (6...31) 4 to 29 ( ) Reset 7/15 480

19 CONTROLS ALCO PS2 SERIES DUAL CONTROLS ORDERING INFORMATION FOR PS2 DUAL CONTROLS ALCO U.S. PCN Standard Product Offering. *Product Code Number. ALCO EUROPE PCN ADJUSTMENT RANGE Upper Setpoint Differential Left PSIG (BAR) Right PSIG (BAR) Left PSIG (BAR) Right PSIG (BAR) FACTORY SETTING Left PSIG (BAR) Right PSIG (BAR) CONNECTION COMBINED LIMITER/SAFETY CUT OUT FOR LOW /HIGH PROTECTION PS2-T7A /16-20 UNF PS2-T7K Internal 15 Hg to to to 72 Manual Reset 50/ PS2-T7L Capillary/solder ( ) (6...31) ( ) High Press. (3.5/4.5) (20) PS2-T7U (4) fixed Solder 6 mm PS2-T7X Solder tube 1/4 COMBINED CUT OUT FOR LOW /HIGH PROTECTION PS2-B7A /16-20 UNF External External PS2-B7K Hg to to 450 Manual Reset Manual Reset PS2-B7L Capillary/solder ( ) (6...31) Low Press. High Press. (4.5) (20) PS2-B7U Solder 6 mm 15 (1) fixed 60 (4) fixed PS2-B7X Solder tube 1/4 COMBINED CUT OUT FOR HIGH /HIGH PROTECTION PS2-G8A /16-20 UNF External Internal PS2-G8K Hg to to 450 Manual Reset Manual Reset PS2-G8L Capillary/solder ( ) (6...31) Low Press. High Press. (4.5) (20) PS2-G8U Solder 6 mm 15 (1) fixed 60 (4) fixed PS2-G8X Solder tube 1/4 OLD TO NEW CROSS REFERENCE (FF215 TO PS2) REPLACES THE COMPETITION OLD MODEL OLD PCN NEW MODEL NEW PCN COPELAND* RANCO PENN DANFOSS SAGINOMIYA FF215-S7-BAUK FF215-S9-BAUK FF215-S7-BAUA FF215-S7-BAAA FF215-S7-BAAK FF215-S7-BAAL FF215-S7-BARA FF215-S7-BARL FF215-S7-BAUL PS2-Y7K 50/65* 230/290 PS2-Y9K 7/15* 230/290 PS2-Y7A 50/65* 230/290 PS2-A7A 50/65* 230/290 PS2-X7K 50/65* 230/290 PS2-A7L 50/65* 230/290 PS2-L7A 50/65* 290 PS2-L7L 50/65* 290 PS2-Y7L 50/65* CP2M-7K O O O O O O CP2M-7A O O O P70LB-1 P70LB-6 P70MA-1 P70MA-18 P70LB-1 P70LB-6 P70MA-1 P70MA-18 P170LB-1 P170MA-1 P78LCA-9300 P78LCA-9320 P78MCA-9300 P78MCA-9320 KP KP KP KP *The Alco control may be used with bracket (PCN ) to allow replacement of the Copeland control with the same mounting configuration. DNS-D304X DNS-D306X DNS-D604X DNS-D606X DNS-D706X DNS-D304XM DNS-D304XML DNS-D306XM DNS-D306XML DNS-D604XM DNS-D606XM DNS-D606XMM 481

20 CONTROLS ALCO PS2 SERIES DUAL CONTROLS PS1 DIMENSIONAL DIAGRAM DIMENSIONS SHOWN ARE IN INCHES. ANGLED MOUNTING BRACKET Alco U.S. PCN #097215, KB Alco Europe PCN # PS2 PARTS/ACCESSORIES UNIVERSAL ANGLE BRACKET Alco U.S. PCN #097064, KB Alco Europe PCN # MOUNTING BRACKET Z TYPE Alco U.S. PCN #097063, KB Alco Europe PCN # KNOB AND LOCK PLATE KIT Alco U.S. PCN #097061, KB Alco Europe PCN # Kit consists of adjustment knob, lockplate (2), pan-head screw (1) and fillister head screw with lock-wire hole (2). 482

21 CONTROLS ALCO FD113-ZU(K) OIL SAFETY CONTROLS The FD113 Oil Pressure Safety Control senses the effective oil pressure on pressure lubricate compressors. If inadequate oil pressure exists, a time delay is energized. If the oil pressure does not recover to safe levels within the time delay setting, the compressor is shut down. The time delay allows the compressor adequate time to establish oil pressure on start up and avoids nuisance shutdowns on pressure drop of short duration during the run cycle. Maximum application flexibility is assured by providing an adjustable differential pressure switch which can be adjusted to the compressor s minimum required oil pressure needs and an adjustable electronic time delay which allows you to select the length of time the compressor runs below the minimum pressure before shutdown. The minimum pressure setting and time delay values specified by the compressor manufacturer should be used when installing the FD113 control. FEATURES Pressure range adjustable from 4 to 65 PSID; Timer start pressure-timer stop pressure is 3 PSID above timer start pressure. A SPDT switch is used in the pressure portion of the control which allows the addition of a safe light if desired. Electronic timer is Timer-Adjustable from 20 to 150 seconds. Supply voltage - 24 to 240 Volt AC/DC. Timing unaffected by voltage or ambient temperature variations. A SPDT Manual Reset Switch is used in the Timer Module. Upon time-out, the compressor is stopped and an alarm circuit is energized. To restart the compressor and de-energize the alarm circuit, the reset button is pushed. A factory installed jumper allows the FD113 to be powered from a single power source. Should separate circuits be desired for the timer and Lockout switch, the jumper can be removed. P1023 SPECIFICATIONS Agency approvals include: UL/CUL file #E85974, VDE 0631/0660, TUV, CE 73/23/EWG, CE 93/68/EWG. DIMENSIONS SHOWN ARE IN INCHES. FD113 DIMENSIONAL DATA A typical 3 wire hookup with the factory installed jumper. P1023B P1023A ORDERING INFORMATION FOR FD113-ZU(K) OIL SAFETY CONTROLS PCN TPC-FD-113-ZUK ADJUSTABLE RANGE 4-65 PSID ADJUSTABLE TIME 20 to 150 seconds SUPPLY VOLTAGE 24 to 240V AC/DC CONNECTION (2) 36 capillary with 1/4 flare nut TPC-FD-113-ZU (2) 1/4 male flare* REPLACES PENN COPELAND RANCO P45NCA-12 P45NCA-82 P28AA-1,-2 P28AA-17,-18 P28DA-1 P28GA-2 P28NA-5 P128AA-1,-2,-3 P145NCA-12,-82 P145NCB-12, P P P P P *For applications where the condensing unit/control is exposed to temperatures below 20 F, 1/4 lines are recommended. 483