2009 Kia Borrego LX ACCESSORIES & BODY, CAB Seat Electrical - Borrego Canadian
|
|
- Bennett Stevenson
- 6 years ago
- Views:
Transcription
1 ACCESSORIES & BODY, CAB Seat Electrical - Borrego Canadian COMPONENTS AND COMPONENT LOCATIONS COMPONENT LOCATION Fig. 1: Locating Motors & Switches POWER SEAT MOTOR REPAIR PROCEDURES Inspection Slide Motor Limit Switch 1. Disconnect the limit switch (A) and operate the limit switch. 2. Check for continuity between the terminals. 3. Make sure that the seat operation is normal in the reverse after the maximum operation.
2 4. If there is an abnormality, replace the limit switch. Fig. 2: Identifying Slide Motor Limit Switch & Connector Terminals Fig. 3: Slide Motor Limit Switch Connector Terminals Chart Reclining Motor Limit Switch 1. Disconnect the limit switch and operate the limit switch. 2. Check for continuity between the terminals. 3. Make sure that the seat operation is normal in the reverse after the maximum operation. 4. If there is an abnormality, replace the limit switch.
3 Fig. 4: Identifying Reclining Motor Limit Switch & Connector Terminals Fig. 5: Reclining Motor Limit Switch Connector Terminals Chart Power Seat Motor 1. Disconnect the connectors for each motor. Fig. 6: Identifying Power Seat Motors (1 Of 2)
4 Fig. 7: Identifying Power Seat Motors (2 Of 2) 2. With the battery connected directly to the motor terminals, check if the motors run smoothly. 3. Reverse the connections and check that the motor turns in reverse. 4. If there is an abnormality, replace the motors. Fig. 8: Identifying Power Seat Motor Connectors & Terminals Fig. 9: Power Seat Motor Connector Terminals Chart POWER SEAT CONTROL SWITCH REPAIR PROCEDURES
5 Inspection 1. With the power seat switch in each position, make sure that continuity exists between the terminals below. If continuity is not as specified, replace the power seat switch. Fig. 10: Identifying Power Seat Control Switch & Connector Terminals Fig. 11: Power Seat Switch Connector A Terminals Chart
6 SEAT HEATER SWITCH REPAIR PROCEDURES Inspection Front Seat Heater Switch 1. Disconnect the negative (-) battery terminal. 2. Remove the seat heater switch from the floor console (A) with scraper. Fig. 12: Removing Seat Heater Switch From Floor Console 3. Check that continuity exists between the terminals. Terminal No : 1. Ground, 2. High signal switch 3. Low signal switch, 5. Illumination (-), 6. Illumination (+)
7 Fig. 13: Front Seat Heater Switch Circuit Diagram 2nd Seat Heater Switch 1. Disconnect the negative (-) battery terminal. 2. Remove the rear door trim. (Refer to "REAR DOOR ") 3. Turn 2nd seat heater switch ON and check that continuity exists between the terminals. Fig. 14: Identifying 2nd Seat Heater Switch & Connector Terminals Fig. 15: 2nd Seat Heater Switch Connector Terminals Chart SEAT HEATER COMPONENTS AND COMPONENT LOCATIONS Component Location
8 Fig. 16: Locating Seat Heater & RH/LH Switches (Driver/Assist Seat) Fig. 17: Locating RH/LH Seat Heater Switches (2nd Seat) REPAIR PROCEDURES Inspection First Seat Heater
9 1. Check for continuity and measure the resistance between No. 1 and No. 3 terminals. Fig. 18: Measuring Resistance Between No. 1 & No. 3 Terminals Standard value Cushion : 4.5ohms ± 10%, Back : 3.96ohms ± 10% 2. Operate the seat warmer after connecting the 3P connector, and then check the thermostat by measuring the temperature of seat surface. Standard value HI : ± 35.6 F (42 ± 2 C) (Cushion), ± 35.6 F (52 ± 2 C) (Back) 3. Check for continuity between the terminals after disconnecting the connector. Fig. 19: First Seat Heater Connector Terminals Chart 2nd Seat Heater 1. Check for continuity and measure the resistance between No. 1 and NO. 3 terminals.
10 Fig. 20: Measuring Resistance Between No. 1 & No. 3 Terminals Standard value Cushion : 4.36ohms ± 10% 2. Operate the seat warmer after connecting the 3P connector, and then check the thermostat by measuring the temperature of seat surface. Standard value Cushion : 104 ± 35.6 F (40 ± 2 C)
SEAT LOCATION INDEX SEAT REMOVAL/INSTALLATION Mazda MX-5 Miata Sport ACCESSORIES & BODY, CAB Seats - MX-5 Miata
SEAT LOCATION INDEX 2007 ACCESSORIES & BODY, CAB Seats - MX-5 Miata Fig. 1: Identifying Location Of Seat Components SEAT REMOVAL/INSTALLATION WARNING: Handling the seat (side air bag) improperly can accidentally
More informationCOMPONENTS Toyota RAV ACCESSORIES & EQUIPMENT Front Seat - RAV4
2005 ACCESSORIES & EQUIPMENT Front Seat - RAV4 COMPONENTS Fig. 1: Identifying Front Seat Components & Torque Specifications FRONT SEAT ASSEMBLY REMOVAL CAUTION: Wear safety gloves, because the cutting
More informationPOWER WINDOWS Toyota 4Runner DESCRIPTION & OPERATION TROUBLE SHOOTING COMPONENT TESTS POWER WINDOW SWITCH CONTINUITY TEST (DRIVER S SIDE SWITCH)
POWER WINDOWS 1995 Toyota 4Runner 1995-96 ACCESSORIES & EQUIPMENT Toyota Power Windows - Trucks 4Runner DESCRIPTION & OPERATION System components consist of a power window relay, power window switches
More informationADJUSTER ANCHOR REMOVAL/INSTALLATION
ADJUSTER ANCHOR REMOVAL/INSTALLATION WARNING: The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-pillar, disconnect the negative battery cable or work carefully,
More informationPOWER MIRRORS 8T - 1 POWER MIRRORS CONTENTS
J POWER MIRRORS 8T - 1 POWER MIRRORS CONTENTS page DIAGNOSIS... 1 GENERAL INFORMATION... 1 page SERVICE PROCEDURES... 4 GENERAL INFORMATION Power outside rear view mirrors are an available option on XJ
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION HEATED SEAT MODULE (HSM), MEMORY SEAT MODULE (MSM) OR MEMORY HEATED SEAT MODULE (MHSM) NOTE: After installation, initialize memory seat module. Move each power seat adjuster motor,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27871 CIVIC IN-DASH CD CHANGER 2- AND 4-DOOR Issue Date AUG 2004 PARTS LIST In-Dash CD Changer Attachment: P/N 08B06-S5D-110 CD Changer
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1993 Mitsubishi Montero 1993 ACCESSORIES & EQUIPMENT Mitsubishi Cruise Control Systems Montero DESCRIPTION & OPERATION The cruise control system is electronically and vacuum controlled.
More informationENGINE COOLING FAN Toyota Celica ELECTRIC COOLING FAN RADIATOR COOLING FAN SYSTEM TEST ENGINE COOLING Toyota Engine Cooling Fans
ENGINE COOLING FAN 1994 Toyota Celica 1994 ENGINE COOLING Toyota Engine Cooling Fans Celica 1.8L 4-Cyl ELECTRIC COOLING FAN NOTE: Electric cooling fan may be used for radiator or condenser. To verify electric
More informationAUTOMATIC SHOULDER BELT SYSTEM
AUTOMATIC SHOULDER BELT SYSTEM 1992 Subaru SVX 1992-96 ACCESSORIES/SAFETY EQUIPMENT Subaru Automatic Shoulder Belt System Subaru; SVX OPERATION RAIL & MOTOR NOTE: After replacing any parts/components,
More informationTape the screwdriver tip before use. Using a screwdriver, remove the inside handle bezel.
Page 1 of 16 DISASSEMBLY 1. REMOVE DOOR INSIDE HANDLE BEZEL a. Using a screwdriver, open the cap. Tape the screwdriver tip before use. b. c. Remove the screw. Using a screwdriver, remove the inside handle
More information2/26/2018 Seating - Seat - Front - Removal and Installation 2010 Ford F-150 MotoLogic Seating 2010 F-150
2010 F-150 Report a problem with this article 501-10 Seating 2010 F-150 REMOVAL AND INSTALLATION Procedure revision date: 07/01/2009 Driver Seat Seat Front NOTE: Refer to the installation steps for tightening
More informationINTERIOR GROUP 52A 52A-1 CONTENTS GENERAL DESCRIPTION... 52A-2 INSTRUMENT PANEL AND FLOOR CONSOLE... 52A-3 SEAT BELT... 52A-10 TRIMS...
52A-1 GROUP 52A CONTENTS GENERAL DESCRIPTION......... 52A-2 INSTRUMENT PANEL AND FLOOR CONSOLE..................... 52A-3 ACCESSORIES................. 52A-4 INSIDE REAR VIEW MIRROR...... 52A-5.........................
More informationSTARTING SYSTEM LOCATION INDEX [LF]
1. Remove the battery cover. 2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF].) 3. Remove the side cover. (LH) 2007 Mazda MX-5 Miata Sport 2007 ENGINE Starting System -
More information6. Rear Seat Belt. Rear Seat Belt A: REMOVAL SB SEAT BELT OUTER - REAR RH AND LH (4 DOOR MODEL)
SEAT ELT SYSTEM Rear Seat elt 6. Rear Seat elt A: REMOVAL 1. SEAT ELT OUTER - REAR RH AND LH (4 DOOR MODEL) 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting
More information1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical.
2004 GMC Envoy 4.2L Eng 1Search IGNITION SWITCH CYLINDER REQUESTED INFORMATION Ignition Lock Cylinder Replacement Removal Procedure 1. Disconnect the negative battery cable. Refer to Battery Negative Cable
More informationTOYOTA CAMRY LE / SE / XLE DUAL SEAT HEATER KIT Section I Pre-Installation Check
Section I Pre-Installation Check Kit Part Number: 250-1897 3 General Applicability Camry LE / SE / XLE 5 4 1 Recommended Sequence of Application Item # Accessory 1 Wiring 2 Elements 3 2 Kit Contents Item
More informationA/C-HEATER SYSTEM - AUTOMATIC
A/C-HEATER SYSTEM - AUTOMATIC 1993 Toyota Celica 1993 Automatic A/C-Heater Systems Celica SPECIFICATIONS SPECIFICATIONS TABLE Application Specification Compressor Type 1.6L... Nippondenso 10PA15C 10-Cyl.
More informationBefore performing spark test, ensure ignitor is properly grounded.
Page 1 of 10 IGNITION CHECKS SPARK TEST NOTE: Before performing spark test, ensure ignitor is properly grounded. 1. Disconnect high tension coil wire from distributor. Hold coil wire approximately 1/2"
More informationCab Heater and Air Conditioner, Pneumatically Controlled 83.01
Cab Heater and Air Conditioner, Pneumatically Controlled.0 Temperature Actuator Replacement. Remove the quick-release screws, then remove the IP fuse junction panel trim See Fig.. 0//9 f4 Fig., Floor Duct
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E12-T2A-100B Application 2014 ACCORD 4-DOOR Publications No. AII 49980 Issue Date AUG 2013 PARTS LIST Right front illuminated door sill trim Fuse label 2 Alcohol
More informationCHASSIS TECH TIPS. Subject: VOLTAGE DROP TEST
Subject: VOLTAGE DROP TEST 1. RELEVANT MODELS: All Hino Models (Cab over and Conventional) 2. COMPLAINT: Electrical failure 3. CAUSE/CONDITION: High resistance and poor connections 4. CORRECTION: Proper
More informationARTICLE BEGINNING * PLEASE READ THIS FIRST * DESCRIPTION OPERATION ATC COMPUTER BLEND-AIR DOOR ACTUATOR CONTROL PANEL
A/C-HEATER SYSTEM - AUTOMATIC Article Text 1989 Chrysler LeBaron Sedan For m m m m m Copyright 1998 Mitchell Repair Information Company, LLC Thursday, July 03, 2003 10:15AM ARTICLE BEGINNING 1989 AUTOMATIC
More informationREMOVAL AND INSTALLATION
501-10-1 Seating 501-10-1 REMOVAL AND INSTALLATION Seat Exploded View, Front Front Seat Backrest NOTE: LH shown, RH similar. 1 64417 Backrest trim cover 2 14D696 Heated seat element (if equipped) 3 64810
More information2014 Hyundai Veloster ENGINE Ignition System - Veloster Turbo. Ignition System - Veloster Turbo
DESCRIPTION AND OPERATION DESCRIPTION 2013-14 ENGINE Ignition System - Veloster Turbo Ignition timing is controlled by the electronic control ignition timing system. The standard reference ignition timing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD/CASSETTE PLAYER 2005 CIVIC 2- AND 4-DOOR AII 27857 Issue Date AUG 2004 PARTS LIST Cassette Player: P/N 08A53-S5A-100 Cassette player
More informationTECHNICAL INSTRUCTIONS FOR NONCOMPLIANCE E0B SEAT HEATER ASSEMBLIES CERTAIN SIENNA
TECHNICAL INSTRUCTIONS FOR NONCOMPLIANCE E0B SEAT HEATER ASSEMBLIES CERTAIN 2013-2014 SIENNA I. OPERATION FLOW CHART The flow chart is for reference only. DO NOT use it in place of the full technical instructions.
More informationAUDIO SYSTEM 8F - 1 AUDIO SYSTEM TABLE OF CONTENTS
PL AUDIO SYSTEM 8F - 1 AUDIO SYSTEM TABLE OF CONTENTS page GENERAL INFORMATION INTRODUCTION...1 DESCRIPTION AND OPERATION INTERFERENCE ELIMINATION...1 DIAGNOSIS AND TESTING AUDIO DIAGNOSTIC TEST PROCEDURES...1
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AUTOMATIC AII 27160 2005 CR-V Issue Date ATTACHMENT KIT SEP 2004 PARTS LIST Automatic Day/Night Mirror Attachment Kit (sold separately)
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationGEAR SELECTOR CABLE. Remove and refit. Removing. Fig. 22
GEAR SELECTOR CABLE Remove and refit Fig. 22 his operation requires the removal of the centre console side casing. lace the quadrant selector lever in "1". Unscrew the gear selector knob (1, Fig. 22).
More informationINSTRUMENT PANEL ASSEMBLY
2003 Dodge or Ram Truck RAM 1500 Truck 2WD V8-4.7L VIN N Vehicle > Body and Frame > Interior Moulding / Trim > Dashboard / Instrument Panel > Service and Repair > Removal and Replacement INSTRUMENT PANEL
More information2008 Toyota RAV ELECTRICAL Charging (2AZ-FE) - RAV4
2008 ELECTRICAL Charging (2AZ-FE) - RAV4 CHARGING SYSTEM PRECAUTION 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables if a quick charge is given
More informationBUZZERS, RELAYS & TIMERS
ELECTRICAL COMPONENT LOCATOR 1994 ELECTRICAL COMPONENT LOCATION Mazda Electrical s BUZZERS, RELAYS & TIMERS BUZZERS, RELAYS & TIMERS LOCATION ABS s Motor Relay On top of ABS pump, on right rear corner
More informationTroubleshoot Safety Circuits
Troubleshoot Safety Circuits Troubleshoot Safety Circuits GMEC96 and GMVC96 Furnaces Safety circuits serve to control any potential safety hazards, and are in place to ensure proper furnace operation.
More informationSeats ! WARNING: SEAT ADJUSTMENT. Seat fore and aft position and, if specified, cushion height and front tilt (B):
Seats SEAT ADJUSTMENT Do not make adjustments when the vehicle is moving. Front passengers must not ride with the seat fully reclined. Front seat adjustment The front seats are adjusted electrically by
More informationOT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL
More informationSEATS. Seats. Front Seats. Front Bucket Seats
2012 Ford Truck F 150 2WD V8-5.0L Vehicle > Body and Frame > Seats > Description and Operation > Components SEATS Seats Front Seats Front Bucket Seats NOTE: For component identification and locations,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CHANGER ATTACHMENT (TRUNK MOUNT) 2005 CIVIC 4-DOOR AII 27890 Issue Date AUG 2004 PARTS LIST Changer Attachment (sold separately) P/N 08B26-S5D-100
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda For Models With Manual Climate Controls TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-7509 APPLICATIONS Mazda 5 2006-2007 For Models With Manual Climate Controls 99-7509 KIT FEATURES Painted To Match Factory Dash DIN Radio Provision with Pocket ISO
More informationTOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
More informationHOW TO PROCEED WITH TROUBLESHOOTING
2005 BRAKES Anti-Lock Brake System With Electronic Brake Force Distribution (EBD) - Diagnostics - RAV4 HOW TO PROCEED WITH TROUBLESHOOTING Troubleshoot in accordance with the following procedures. Fig.
More information2. Front Seat FRONT SEAT
SEATS 2. Front Seat A: REMOVAL 1) Disconnect the ground cable from battery. CAUTION: The airbag system is fitted with a backup power source. If the airbag system is serviced within 20 seconds after the
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS ATTACHMENT P/N 08T70-MGZ-D80 CB500X/XA MII 14565 Issue Date May 2013 PARTS LIST KIT Sold separately (1) (2) (4) (2) (1) (3) BOOT (1 piece.)
More informationINTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE
Page 1 of 18 2016 Dodge Grand Caravan 3.6L Eng VIN G SE Service Manual: BODY - INTERIOR & EXTERIOR Print Date: INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE Fig 1: Base Floor Console
More information1 of 6 10/31/2017, 1:57 PM. Fig. 19 Automatic Transmission Shift Knob Removal
1 of 6 10/31/2017, 1:57 PM Fig. 19 Automatic Transmission Shift Knob Removal 2 of 6 10/31/2017, 1:57 PM Fig. 20 Manual Transmission Shift Knob Removal 3 of 6 10/31/2017, 1:57 PM Fig. 21 Removing Accessory
More informationPage 1 of 7 Service Manual: CHARGING SYSTEM B TERMINAL CIRCUIT > DESCRIPTION 2007 Nissan Altima 2.5L Eng S The terminal "1" circuit supplies power to charge the battery and operate the vehicles electrical
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chevrolet Corvette D A B
INSTLLTION INSTRUCTIONS FOR PRT 99-05 PPLICTIONS Chevrolet Corvette 990-996 99-05 KIT FETURES ISO mount Radio Provision with Pocket Two ISO Mount Unit s Provision Double DIN Radio Provision KIT COMPONENTS
More informationDodge opening upper console w/non-opening middle bottom Installation
2009-12 Dodge 40-20-40 opening upper console w/non-opening middle bottom Installation Step 1. Prepare the driver and passenger seat for installation by temporarily removing the headrests. Recline the backrests
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chevrolet Corvette D A B
INSTLLTION INSTRUTIONS FOR PRT 99-05 PPLITIONS hevrolet orvette 990-996 99-05 KIT FETURES ISO mount Radio Provision with Pocket Two ISO Mount Unit s Provision Double DIN Radio Provision KIT OMPONENTS (
More informationInstallation Instructions
KALA0601AAA KALA0701AAA MotorMasterR Low Ambient Controller for Residential plit ystem Applications Installation Instructions Fig. 1 - MotorMasterr Low Ambient Controller A93157 NOTE: Read the entire instruction
More informationPOWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. DESCRIPTION: APPLICATION: PART NUMBER: Accent light Kit Cube (MY2013+) 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS HEATED GRIP ATTACHMENT P/N 08T70-MJE-D00 CBR650F/FA MII 14960 Issue Date April 2014 PARTS LIST HEATED GRIP Sold separately (1) (2) (4) (2)
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1992 Infiniti G20 1991-92 SAFETY EQUIPMENT Infiniti Cruise Control Systems G20, M30, Q45 DESCRIPTION & OPERATION NOTE: For system component locations, see SYSTEM COMPONENT LOCATIONS.
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationALTERNATOR & REGULATOR - NIPPONDENSO
ALTERNATOR & REGULATOR - NIPPONDENSO 1988 Toyota Celica 1988 ELECTRICAL Alternators & Regulators - Nippondenso Camry, Celica, Corolla, Cressida, Land Cruiser, MR2, Pickup, Supra, Tercel, Van, 4Runner DESCRIPTION
More informationBefore performing symptom troubleshooting, check for power train DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
2003 Honda Civic 1.7L Eng LX Component AC PRESSURE SENSOR A/C Pressure Switch Circuit Troubleshooting NOTE: Do not use this troubleshooting procedure if any of the following items are operative; condenser
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27996 ATTACHMENT KIT 2005 CIVIC HYBRID Issue Date AUG 2004 PARTS LIST Changer Attachment Kit: P/N 08B26-S5B-100 4 Washer-screws, 4 x
More informationDRIVE BELT AUTO-TENSIONER AIR BLEEDING
2012 ENGINE Drive Belt - Civic DRIVE BELT AUTO-TENSIONER AIR BLEEDING REMOVAL 1. Move the auto-tensioner (A) counterclockwise to relieve tension from the drive belt (B). 2. Remove the drive belt. BLEEDING
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More informationCHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS
TJ CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS page DESCRIPTION AND OPERATION BATTERY TEMPERATURE SENSOR... 2 CHARGING SYSTEM OPERATION... 1 ELECTRONIC VOLTAGE REGULATOR... 2 GENERATOR... 1 DIAGNOSIS
More information2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6
2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6 Vehicle» Body and Frame» Interior Moulding / Trim» Dashboard / Instrument Panel» Service and Repair» Instrument Panel Assembly REMOVAL
More informationSection 55 Chapter 6
Section 55 Chapter 6 REMOTE HYDRAULICS CONTROLLER Calibration and Fault Codes 6-12880NH TABLE OF CONTENTS REMOTE HYDRAULICS CONTROLLER CALIBRATION... 55-5 Requirements For Calibration... 55-5 Aux Set Main
More informationPage 1 of 6 Pinpoint Test R: The Heated Seat is Inoperative Driver Refer to Wiring Diagrams Cell 119, Climate Controlled Seats for schematic and connector information. rmal Operation The heated seat module
More informationTOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation
Section I - Installation Preparation Part Number: 08586-04810 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4
More informationSEAT BELT WARNING SYSTEM
SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS HEATED GRIPS ATTACHMENT KIT P/N 08T70-MJL-D30 2014-2015 NC700X/XD Honda Dealer: Please give a copy of these instructions to your customer.
More informationON-VEHICLE INSPECTION
51 Connector Front Side: A5 ON-VEHICLE INSPECTION 1. INSPECT TOWING CONVERTER RELAY (a) Measure the voltage and check the result in accordance with the value(s) in the table below. Standard E064833E01
More informationIgniter Unit Test ACCORD AND PRELUDE WITH HITACHI DISTRIBUTOR. See Figure 2
Igniter Unit Test 1984-89 ACCORD AND PRELUDE WITH HITACHI DISTRIBUTOR See Figure 2 This procedure is not applicable to 1988-89 fuel injected Preludes. 1. Remove the distributor cap. 2. Disconnect the lead
More information01 02B ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)]
ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)] CONTROL SYSTEM WIRING DIAGRAM [FS]............................ 2 CONTROL SYSTEM DEVICE AND CONTROL RELATIONSHIP CHART [FS]........ 4 Engine Control System............
More information1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME
2006 Toyota 4Runner 4.0L Eng Limited 1Search AIR CONDITIONER REQUESTED INFORMATION PRECAUTION 1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME 2. ALWAYS WEAR EYE PROTECTION Fig 1:
More informationDESCRIPTION & OPERATION
SEATS - POWER 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Power Seats DESCRIPTION & OPERATION Power seats operate using toggle switches located on seat side. Seat adjusters are powered by a 12-volt,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate Maxima (Applicable ONLY to U.S. Market Vehicles with Build Date June 2012 or later) 999G6
More informationIFD AIR CLEANER SERVICE MANUAL
IFD AIR ER SERVICE MANUAL PUB NO. 34-3446-01 1 4 COMPONENTS OF THE AIR ER 5 3 6 3 2 7 8 1 2 3 AIR FLOW 1 1) Pre-filter - traps large particles such as hair and lint before they can enter the cell section.
More informationDZ: Universal Heated Oxygen Sensor (HO2S)
2009 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 02/23/2010 DZ: Universal Heated Oxygen Sensor (HO2S) DZ: Introduction DZ1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1990 Nissan 240SX 1990 ACCESSORIES & EQUIPMENT Nissan Cruise Control Systems Axxess, Maxima, Pathfinder, Pickup, Stanza, 240SX, 300ZX DESCRIPTION & OPERATION NOTE: For system component
More informationA/C-HEATER SYSTEM - AUTOMATIC
A/C-HEATER SYSTEM - AUTOMATIC 1988 Toyota Celica 1988 Automatic A/C-Heater Systems Celica * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system, use only approved refrigerant recovery/recycling
More informationRoadComfort TM. Installation Manual Vibration Massage & Heat
RoadComfort TM Vibration Massage & Heat Installation Manual 1-562-447-1780 WWW.RELAXOR.COM Table of Contents I Required tools II System Configuration III Motor Placement Bottom IV Motor Placement Back
More informationFK75 / FK95 Quick Installation Guide
FK75 / FK95 Quick Installation Guide Battery - Pin 1 2 3 4 5 6 7 Fan Potentiometer 9 10 11 Battery + Fan + Setting the Temperature The controller is set from the factory for use with a 10 degree thermostat,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. After 13 TRX420 All MII 15067 KIT (except 14 TRX420FA/FPA) Issue Date P/N 08T71-HR3-A20 After 13 TRX500 All (except 14 TRX500FA/FPA) September
More informationSUNROOF. SUNROOF Component Parts and Harness Connector Location RF-10
omponent Parts and Harness onnector Location PFP:91210 NIS0023Q PII6291E 1. Fuse block (J/) 2. Fuse and fusible link box 3. M M1, M2, M3 (View with the glove box assembly removed) 4. Sunroof motor assembly
More informationCorolla TNS600. RHD installation instructions. Model year: 2004 Vehicle code: **E12*R-****W
Corolla RHD installation instructions Model year: 2004 Vehicle code: **E12*R-****W Part number: Navigation System PZ 445-00331-00 Clusterpanel 55406-02070-B0 Manual ref. no: AIM 000 767-0 PRECAUTIONS PLEASE
More informationSeat Cushion Front. Driver Power Front Seat Cushion. Item Part Number Description Cushion trim cover
SECTION 501-10: Seating 2009 Mustang Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/23/2008 Seat Cushion Front Special Tool(s) Vehicle Communication Module (VCM) and Integrated Diagnostic
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationRADIATOR CLEANING OF RADIATOR
CO20 COOLING SYSTEM RADIATOR CLEANING OF RADIATOR Using water or a steam cleaner, remove any mud and dirt from the radiator core. CAUTION: If using a high pressure type cleaner, be careful not to deform
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2004 TSX BII 24811 Issue Date APRIL 2003 PARTS LIST Attachment Kit P/N 08B23-SDA-101A Monitor bracket harness FM
More informationMFH-5398 Block Only Fresh Water Cooling Kit Instructions
MFH-5398 Block Only Fresh Water Cooling Kit Instructions IMPORTANT Before you unpack the kit and start installation, make sure you have the right kit for your engine by studying these installation instructions.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PRTS INSTLLTION INSTRUCTIONS 1. 2. 3. DESCRIPTION: PPLICTION: PRT NUMER: Radiant Grille Emblem Q50 F2890 6H1 4. KIT CONTENTS: Item Qty. Description Part Number 1 Illuminated Emblem F2890 6H0 1
More informationPOWER MIRROR SYSTEMS
DN POWER MIRROR SYSTEMS 8T - 1 POWER MIRROR SYSTEMS TABLE OF CONTENTS EXTERIOR MIRRORS... 1 INTERIOR MIRRORS... 5 EXTERIOR MIRRORS TABLE OF CONTENTS INTRODUCTION...1 POWER MIRROR SYSTEM...1 POWER MIRROR....1
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS!
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. When using electrical equipment, basic safety precautions should always be followed including the following: DISCONNECT AC POWER SUPPLY BEFORE
More information2005 Honda Civic DX. Information marked with an asterisk (*) applies to the D17A2 engine.
DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION NOTE: Information marked with an asterisk (*) applies to the D17A2 engine. 1. Reset the ECM/PCM (see HOW TO RESET THE ECM/PCM ). 2. Start the
More informationINSTRUMENT PANEL Volvo 960 * PLEASE READ THIS FIRST * DESCRIPTION & OPERATION TESTING ACCESSORIES/SAFETY EQUIPMENT Volvo Instrument Panel
INSTRUMENT PANEL 1994 Volvo 960 1994 ACCESSORIES/SAFETY EQUIPMENT Volvo Instrument Panel 960 * PLEASE READ THIS FIRST * WARNING: When working around steering column and before performing repairs, disconnect
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationCOMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2011-12 ENGINE Cooling System - TSX V6 Fig. 1: Identifying Cooling System Components RADIATOR CAP TEST 2. Wait until the engine is cool, then carefully remove the radiator cap
More informationMANUAL TRANSMISSION Click on the applicable bookmark to selected the required model year
MANUAL TRANSMISSION 22-1 MANUAL TRANSMISSION CONTENTS LUBRICANT............................... 2 SEALANTS AND ADHESIVES.............. 2 ON-VEHICLE SERVICE..................... 2 Transmission Oil Check.......................
More informationINTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52A-1 INTERIOR AN SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CONTENTS INTERIOR... 52A SUPPLEMENTAL RESTRAINT SYSTEM (SRS)... 52B 52A-2 INTERIOR CONTENTS SPECIAL TOOL... 3 INSTRUMENT PANEL*... 3 FRONT FLOOR CONSOLE...
More informationGENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
More information