6. Rear Seat Belt. Rear Seat Belt A: REMOVAL SB SEAT BELT OUTER - REAR RH AND LH (4 DOOR MODEL)
|
|
- Muriel Lucas
- 5 years ago
- Views:
Transcription
1 SEAT ELT SYSTEM Rear Seat elt 6. Rear Seat elt A: REMOVAL 1. SEAT ELT OUTER - REAR RH AND LH (4 DOOR MODEL) 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. AUTION: The airbag system is fitted with a backup power supply. After disconnecting the battery ground cable, the airbag may operate if you do not wait for 60 seconds before starting the service of airbag system. 2) Remove the rear seat cushion assembly. (1) Push the corners of the rear seat cushion from above. (2) While pushing the corners of the rear seat cushion from above, pull the knob of the hook - seat cushion rear towards yourself. (3) While pulling the knob towards yourself, disconnect the hooks by lifting up the rear seat cushion. NOTE: Pull the left side of the knob to disconnect the LH side hook, and pull the right side of the knob to disconnect the RH side hook. (3) (1) (3) (1) (2) (2) SE S-30
2 Rear Seat elt SEAT ELT SYSTEM (4) Remove the hook by pushing it back while lifting the front side of the rear seat cushion, and remove the rear seat cushion. SE ) Release the clips and claws, and then remove the cover side sill - rear INN. (On the side where seat belt assembly is removed) AUTION: Do not pull with excessive force. Doing so may damage the claws of the cover side sill - rear INN. A-A - - A A D D D-D EI S-31
3 SEAT ELT SYSTEM Rear Seat elt 4) Remove the clips, and remove the trim panel - rear pillar UPR. (On the side where seat belt assembly is removed) 5) Remove the trim panel - rear pillar LWR. (On the side where seat belt assembly is removed) (1) Remove the clips, and turn over the trim panel - trunk side. (2) Remove the clips, and remove the trim panel - rear pillar LWR. EI EI S-32
4 Rear Seat elt SEAT ELT SYSTEM 6) Remove the bolts, and remove the seat belt outer - rear. 2. SEAT ELT OUTER - REAR RH AND LH (5 DOOR MODEL/XV MODEL) 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. S AUTION: The airbag system is fitted with a backup power supply. After disconnecting the battery ground cable, the airbag may operate if you do not wait for 60 seconds before starting the service of airbag system. 2) Remove the rear seat cushion assembly. (1) Push the corners of the rear seat cushion from above. (2) While pushing the corners of the rear seat cushion from above, pull the knob of the hook - seat cushion rear towards yourself. (3) While pulling the knob towards yourself, disconnect the hooks by lifting up the rear seat cushion. NOTE: Pull the left side of the knob to disconnect the LH side hook, and pull the right side of the knob to disconnect the RH side hook. (3) (1) (3) (1) (2) (2) SE S-33
5 SEAT ELT SYSTEM Rear Seat elt (4) Remove the hook by pushing it back while lifting the front side of the rear seat cushion, and remove the rear seat cushion. SE ) Remove the screws and clips, and remove the trim panel - rear quarter pillar UPR. (On the side where seat belt assembly is removed) EI S-34
6 Rear Seat elt SEAT ELT SYSTEM 4) Remove the bolts, and remove the seat belt outer - rear. 3. SEAT ELT - REAR SHOULDER TR (4 DOOR MODEL) 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. S AUTION: The airbag system is fitted with a backup power supply. After disconnecting the battery ground cable, the airbag may operate if you do not wait for 60 seconds before starting the service of airbag system. 2) Remove the rear seat cushion assembly. (1) Push the corners of the rear seat cushion from above. (2) While pushing the corners of the rear seat cushion from above, pull the knob of the hook - seat cushion rear towards yourself. (3) While pulling the knob towards yourself, disconnect the hooks by lifting up the rear seat cushion. NOTE: Pull the left side of the knob to disconnect the LH side hook, and pull the right side of the knob to disconnect the RH side hook. (3) (1) (3) (1) (2) (2) SE S-35
7 SEAT ELT SYSTEM Rear Seat elt (4) Remove the hook by pushing it back while lifting the front side of the rear seat cushion, and remove the rear seat cushion. SE ) Release the clips and claws, and remove the side sill covers - rear INN on the left and right sides. AUTION: Do not pull with excessive force. Doing so may damage the claws of the side sill cover - rear INN. A-A - - A A D D D-D EI S-36
8 Rear Seat elt SEAT ELT SYSTEM 4) Remove the clips, and remove the trim panel - rear pillar UPR on the left and right sides. 5) Remove the trim panel - rear pillar LWR on the left and right sides. (1) Remove the clips, and turn over the trim panel - trunk side. (2) Remove the clips, and remove the trim panel - rear pillar LWR. EI EI S-37
9 SEAT ELT SYSTEM Rear Seat elt 6) Remove the bolts, and remove the lower anchor of the seat belt - rear shoulder TR. EI ) Remove the trim panel - rear shelf assembly. (1) Release the clips to float the trim panel assembly - rear shelf. (2) Release the belt guide, and guide the anchor of the seat belt - rear shoulder TR to behind the trim panel - rear shelf assembly. (3) Disconnect the connector of high-mounted stop light. (4) Remove the trim panel assembly - rear shelf. EI S-38
10 Rear Seat elt SEAT ELT SYSTEM 8) Remove the bolts, and remove the seat belt - rear shoulder TR. S SEAT ELT - REAR SHOULDER TR (5 DOOR MODEL/XV MODEL) 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. AUTION: The airbag system is fitted with a backup power supply. After disconnecting the battery ground cable, the airbag may operate if you do not wait for 60 seconds before starting the service of airbag system. 2) Remove the screws and clips, and remove the trim panel - rear quarter pillar UPR RH. EI S-39
11 SEAT ELT SYSTEM Rear Seat elt 3) Remove the rear seat cushion assembly. (1) Push the corners of the rear seat cushion from above. (2) While pushing the corners of the rear seat cushion from above, pull the knob of the hook - seat cushion rear towards yourself. (3) While pulling the knob towards yourself, disconnect the hooks by lifting up the rear seat cushion. NOTE: Pull the left side of the knob to disconnect the LH side hook, and pull the right side of the knob to disconnect the RH side hook. (3) (1) (3) (1) (2) (2) SE (4) Remove the hook by pushing it back while lifting the front side of the rear seat cushion, and remove the rear seat cushion. SE S-40
12 Rear Seat elt SEAT ELT SYSTEM 4) Release the clips and claws, and then remove the cover side sill - rear INN RH. AUTION: Do not pull with excessive force. Doing so may damage the claws of the cover side sill - rear INN. A-A - - A A D D D-D 5) Remove the clips, and remove the trim panel - rear skirt. EI RS S-41
13 SEAT ELT SYSTEM Rear Seat elt 6) Remove the trim panel - rear apron RH. (1) Remove the caps, and then remove the screws. (2) Remove the clips, and remove the trim panel - rear apron RH. 7) Remove the bolts, and remove the seat belt - rear shoulder TR. EI S S-42
14 Rear Seat elt SEAT ELT SYSTEM 5. SEAT ELT - TR RH AND LH 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. AUTION: The airbag system is fitted with a backup power supply. After disconnecting the battery ground cable, the airbag may operate if you do not wait for 60 seconds before starting the service of airbag system. 2) Remove the rear seat cushion assembly. (1) Push the corners of the rear seat cushion from above. (2) While pushing the corners of the rear seat cushion from above, pull the knob of the hook - seat cushion rear towards yourself. (3) While pulling the knob towards yourself, disconnect the hooks by lifting up the rear seat cushion. NOTE: Pull the left side of the knob to disconnect the LH side hook, and pull the right side of the knob to disconnect the RH side hook. (3) (1) (3) (1) (2) (2) SE (4) Remove the hook by pushing it back while lifting the front side of the rear seat cushion, and remove the rear seat cushion. SE S-43
15 SEAT ELT SYSTEM Rear Seat elt 3) Remove the bolts, and remove the seat belt - TR RH and LH. 4 door model: Seat belt - TR LH 5 door model/xv model: Seat belt - TR RH and LH S S S-44
16 Rear Seat elt SEAT ELT SYSTEM : INSTALLATION 1. SEAT ELT OUTER - REAR RH AND LH (4 DOOR MODEL) 1) efore installation, perform a unit inspection of retractor. <Ref. to S-46, INSPETION, Rear Seat elt.> 2) Install the seat belt outer - rear. AUTION: During installation, make sure that the seat belts are not twisted. After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: Rear seat belt (4 door model): <Ref. to S-3, REAR SEAT ELT (4 DOOR MODEL), OMPONENT, General Description.> 3) Install the remaining parts in the reverse order of removal. 4) After installation, check the following points. The seat belt is not twisted. The seat belt can be pulled out and retracted smoothly. 2. SEAT ELT OUTER - REAR RH AND LH (5 DOOR MODEL/XV MODEL) 1) efore installation, perform a unit inspection of retractor. <Ref. to S-46, INSPETION, Rear Seat elt.> 2) Install the seat belt outer - rear. AUTION: During installation, make sure that the seat belts are not twisted. After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: Rear seat belt (5 door model/xv model): <Ref. to S-4, REAR SEAT ELT (5 DOOR MODEL/XV MODEL), OMPONENT, General Description.> 3) Install the trim panel - rear quarter trim UPR. 4) Install the remaining parts in the reverse order of removal. 5) After installation, check the following points. The seat belt is not twisted. The seat belt can be pulled out and retracted smoothly. 3. SEAT ELT - REAR SHOULDER TR (4 DOOR MODEL) 1) Install the retractor of seat belt - rear shoulder TR. Tightening torque: Rear seat belt (4 door model): <Ref. to S-3, REAR SEAT ELT (4 DOOR MODEL), OMPONENT, General Description.> 2) Install the trim panel assembly - rear shelf. 3) Install the lower anchor of seat belt - rear shoulder TR. AUTION: During installation, make sure that the seat belts are not twisted. After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: Rear seat belt (4 door model): <Ref. to S-3, REAR SEAT ELT (4 DOOR MODEL), OMPONENT, General Description.> 4) Install the remaining parts in the reverse order of removal. 5) After installation, check the following points. The seat belt is not twisted. The seat belt can be pulled out and retracted smoothly. S-45
17 SEAT ELT SYSTEM Rear Seat elt 4. SEAT ELT - REAR SHOULDER TR (5 DOOR MODEL/XV MODEL) 1) Install the seat belt - rear shoulder TR. Tightening torque: Rear seat belt (5 door model/xv model): <Ref. to S-4, REAR SEAT ELT (5 DOOR MODEL/XV MODEL), OMPONENT, General Description.> 2) Install the remaining parts in the reverse order of removal. 3) After installation, check the following points. The seat belt is not twisted. The seat belt can be pulled out and retracted smoothly. 5. SEAT ELT - TR RH AND LH 1) Install the seat belt - TR RH/LH. Tightening torque: Rear seat belt (4 door model): <Ref. to S-3, REAR SEAT ELT (4 DOOR MODEL), OMPONENT, General Description.> Rear seat belt (5 door model/xv model): <Ref. to S-4, REAR SEAT ELT (5 DOOR MODEL/XV MODEL), OMPONENT, General Description.> 2) Install the rear seat cushion. 3) Install the remaining parts in the reverse order of removal. 4) After installation, check the following points. The seat belt is not twisted. heck that the airbag warning light lights up for approximately 6 seconds and then turns off when connecting the battery ground cable and turning the ignition switch to ON. : INSPETION 1. VISUAL INSPETION heck for the following, and replace with new parts if necessary. Seat belt is slackened, bent or worn. Seat belt is abnormally wound or extended. Seat belt inner - rear is deformed or damaged. Seat belt buckle cannot be engaged properly. S-46
18 Rear Seat elt SEAT ELT SYSTEM 2. ELR LOK MEHANISM INSPETION 1) Hold the retractor upright (as installed in the vehicle) and check the ELR lock mechanism. 2) Tilt the retractor from the upright posture and check the following points. It does not lock if the inclination angle is 15 or less. () S Except for seat belt - rear shoulder TR (5 door model/xv model) () Seat belt - rear shoulder TR (5 door model/xv model) It remains locked if the inclination angle is 27 or more. () S Except for seat belt - rear shoulder TR (5 door model/xv model) () Seat belt - rear shoulder TR (5 door model/xv model) 3) If the ELR lock mechanism does not operate properly, replace the seat belt outer - rear with a new part. S-47
19 SEAT ELT SYSTEM Rear Seat elt S-48
20 LIGHTING SYSTEM LI Page 1. General Description Relay and Fuse Headlight System Day Time Running Light System learance Light and Illumination Light System Front Fog Light System Turn Signal Light and Hazard Light System ack-up Light System Stop Light System Interior Light System Auto Headlight eam Leveler System ombination Switch (Light) Light ontrol Sensor Headlight Assembly Headlight ulb Hazard Switch Turn Signal Light & Hazard Light Module Front Turn Signal Light ulb learance/parking Light ulb Front Side Marker Light ulb Front Fog Light Assembly Front Fog Light ulb Side Turn Signal Light Assembly Rear ombination Light Assembly Tail/Stop Light ulb Rear Turn Signal Light ulb Rear Side Marker Light ulb ack-up Light ulb License Plate Light High-mounted Stop Light Spot Map Light Room Light Luggage Room Light Trunk Room Light Glove ox Light Ignition Switch Illumination Auto Headlight eam Leveler ontrol Module Rear Height Sensor Day Time Running Resistor Reflex Reflector Door Switch...95
13.Curtain Airbag Sensor
urtain Airbag Sensor AIRAG SYSTEM 13.urtain Airbag Sensor A: REMOVAL 1. 4 DOOR MODEL 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. AUTION: Airbag system
More informationADJUSTER ANCHOR REMOVAL/INSTALLATION
ADJUSTER ANCHOR REMOVAL/INSTALLATION WARNING: The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-pillar, disconnect the negative battery cable or work carefully,
More informationSEAT BELT WARNING SYSTEM
SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More information2004 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX
2004 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX BODY SECTION HVAC SYSTEM (HEATER, VENTILATOR AND A/C) HVAC SYSTEM (AUTO A/C) (DIAGNOSTIC) AIRBAG SYSTEM AC AC AB This service manual has been prepared
More information1. General Description
General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module
More informationModel Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
More informationSEAT BELTS SECTION CONTENTS H RESTRAINTS SB-1
H RESTRAINTS A SECTION SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt Service... 2
More informationSEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
More information1 of 13 2/10/ :41 AM
1 of 13 2/10/2017 10:41 AM Trim Removal/Installation - Pillar Areas Special Tools Required KTC trim tool set SOJATP2014 * *Available through the American Honda Tool and Equipment Program A-pillar Trim
More informationINTERIOR GROUP 52A 52A-1 CONTENTS GENERAL DESCRIPTION... 52A-2 INSTRUMENT PANEL AND FLOOR CONSOLE... 52A-3 SEAT BELT... 52A-10 TRIMS...
52A-1 GROUP 52A CONTENTS GENERAL DESCRIPTION......... 52A-2 INSTRUMENT PANEL AND FLOOR CONSOLE..................... 52A-3 ACCESSORIES................. 52A-4 INSIDE REAR VIEW MIRROR...... 52A-5.........................
More information7. Side Airbag Module
AIRBAG SYSTEM Side Airbag Module 7. Side Airbag Module A: REMOVAL Refer to CAUTION of General Description before handling the airbag module. NOTE: Remove
More informationSEAT BELTS SECTION CONTENTS H RESTRAINTS SB-1
H RESTRAINTS A SECTION SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt Service... 2
More information2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX BODY SECION HVAC SYSEM (HEAER, VENILAOR AND A/C) HVAC SYSEM (AUO A/C) (DIAGNOSICS) AIRBAG SYSEM AC AC(diag) AB his service manual has been prepared to
More informationSEAT BELTS SECTION CONTENTS H RESTRAINTS SB-1
H RESTRAINTS A SECTION SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt Service... 2
More informationREASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
More informationREPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
More informationSECOND ROW SEAT BELT SECOND ROW SEAT BELT. Second Row Seat Belt SB-13 EXPLODED VIEW SEAT BELT RETRACTOR < REMOVAL AND INSTALLATION >
SECOND ROW SEAT BELT Second Row Seat Belt EXPLODED VIEW SECOND ROW SEAT BELT INFOID:0000000012551454 A B C D E F G SB I J K L M N O AWHIA0861ZZ P 1. Seat belt height adjuster (LH/RH) 2. Seat belt retractor
More information1. General Description
EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,
More informationSEAT BELT SECTION SB CONTENTS RESTRAINTS SB-1 PRECAUTION... 2 ON-VEHICLE REPAIR... 3
RESTRAINTS SECTION SB A SEAT BELT B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precaution for Seat
More informationROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
More informationINTERIOR TRIM REMOVAL/INSTALLATION - PILLAR AREAS
2010 Honda Truck CR-V 4WD L4-2.4L Vehicle > Body and Frame > Interior Moulding / Trim > Trim Panel > Service and Repair > Removal and Replacement > Pillar Trim INTERIOR TRIM REMOVAL/INSTALLATION - PILLAR
More informationIR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
More informationSafety Belt Retractor and Pretensioner
SECTION 501-20A: Safety Belt System 2009 Mustang Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 12/03/2008 Safety Belt Retractor and Pretensioner Safety Belt Retractor and Pretensioner
More informationAll bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
More information1. General Description
EXERIOR/INERIOR RIM GENERAL DESCRIPION 1. General Description A: COMPONEN 1. FRON GRILLE EI-00413 Front grille Front grille emblem Clip 2. UNDER COVER EI-00414 Under cover Clip (side) ightening torque:
More information2. Front Seat FRONT SEAT
SEATS 2. Front Seat A: REMOVAL 1) Disconnect the ground cable from battery. CAUTION: The airbag system is fitted with a backup power source. If the airbag system is serviced within 20 seconds after the
More information2003 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX
003 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX BODY SECTION HVAC SYSTEM (HEATER, VENTILATOR AND A/C) HVAC SYSTEM (DIAGNOSTICS) AC AC AIRBAG SYSTEM AB This service manual has been prepared to provide SUBARU
More information4. BODY REPAIR. White Body. Without sunroof. With sunroof BODY REPAIR ACTYON SM CHANGED BY EFFECTIVE DATE AFFECTED VIN
12 5110 4. White Body Without sunroof With sunroof 5110 13 Body Dimensions Side Structure Complete Unit: mm INT EXT REPAIR 14 5110 Engine Compartment Unit: mm 5110 15 Front End Unit: mm INT REPAIR EXT
More informationPage 1 of 15 2011 Glass, Frames and Mechanisms - Rear Quarter Window Regulator Motor Removal and Installation Removal 1. Remove the rear quarter trim panels. For additional information, refer to: Rear
More informationSEAT BELTS SECTION SB CONTENTS H RESTRAINTS SB-1
SEAT BELTS H RESTRAINTS SECTION SB A SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt
More informationSeat belts. Safety precautions for handling pyrotechnic seat belt tensioners WARNING!
Page 1 of 41 69-1 Seat belts Safety precautions for handling pyrotechnic seat belt tensioners WARNING! Testing, removing, installing and repair work must only be carried out by properly qualified personnel.
More informationPosition of Parts in Engine Compartment
ELECTRICAL WIRING ROUTING [5S FE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor D 1 Distributor A 2 A/C Condenser Fan Motor A 3 A/C Idle Up VSV E 1 ECT Solenoid A 4 A/C Magnet Clutch
More informationSUNROOF. SUNROOF Component Parts and Harness Connector Location RF-10
omponent Parts and Harness onnector Location PFP:91210 NIS0023Q PII6291E 1. Fuse block (J/) 2. Fuse and fusible link box 3. M M1, M2, M3 (View with the glove box assembly removed) 4. Sunroof motor assembly
More informationINTERIOR GROUP 52A 52A-1 CONTENTS GENERAL INFORMATION... 52A-2 SEAT BELT... 52A-7 INSTRUMENT PANEL AND FLOOR CONSOLE... 52A-3 TRIMS...
52A-1 GROUP 52A CONTENTS GENERAL INFORMATION........ 52A-2 INSTRUMENT PANEL AND FLOOR CONSOLE..................... 52A-3 ACCESSORIES................. 52A-4 SEAT BELT..................... 52A-7 TRIMS.........................
More informationFRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
More informationSRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
More informationInstallation Manual: Honda CRV Power Lift Gate System
Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationREASSEMBLY SE INSTALL REAR SEATBACK LOCK ASSEMBLY (a) Install the rear seatback lock with the 2 bolts. Torque: 18 N*m (185 kgf*cm, 13 ft.
AT REAR AT ASMBLY (for RH Side) 49 REASMBLY CAUTION: Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands. 1. INSTALL REAR
More informationTrim (general) Lower A-pillar trim, removing and installing
Page 1 of 16 70-72 Trim (general) Lower A-pillar trim, removing and installing - To remove, remove A-pillar bolts 4 (2x). Tightening torque: 1.5 Nm (13 in. lb) - Remove door seal -2- in area of A-pillar
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationPosition of Parts in Engine Compartment
ELECTRICAL WIRING ROUTING [3S GTE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor D 1 Date Link Connector 1 (Check Connector) A 2 A/C Condenser Fan Motor D 2 Distributor A 4 A/C Magnetic
More informationSafeGuard Flex Seat Maintenance Guide
SafeGuard Flex Seat Maintenance Guide 1) Preparation For Removal And Replacement Of Seat Back Covers And Retractor Assemblies a) Unlatch seat cushion and pivot cushion up and forward. b) Separate seat
More informationDISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
More informationINTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52A-1 INTERIOR AN SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CONTENTS INTERIOR... 52A SUPPLEMENTAL RESTRAINT SYSTEM (SRS)... 52B 52A-2 INTERIOR CONTENTS SPECIAL TOOL... 3 INSTRUMENT PANEL*... 3 FRONT FLOOR CONSOLE...
More informationDASH/MAIN HARNESS. NOTE: wires 400 & 401, must be twisted together.
Electric Speedo Ground 151 Turn Flasher 16A 4 150 8A, Cluster Connections 31 33 30 35 151 (electric speedo) 402 401 NOTE: wires 400 & 401, must be twisted together. 156D, E Panel Dimmer 8A 9, C 2D Headlight
More informationRESTRAINT SYSTEM SECTIONRS CONTENTS IDX. SEAT BELTS...3 Precautions...3. Disposal of Air Bag Module and Seat Belt Pretensioner
RESTRAINT SYSTEM SECTIONRS GI MA EM LC EC CONTENTS FE SEAT BELTS...3 Precautions...3 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG AND SEAT BELT PRE-TENSIONER...3 PRECAUTION FOR SEAT BELT SERVICE...3 Front
More informationA750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Last Modified: 4-26-2007 Service Category: Drivetrain 1.6 A Section: Automatic Transmission/Transaxle Model Year: 2007 Model:
More information7. MT Gear Shift Lever
7. A: REMOVAL 1. STI MODEL 1) Disconnect the ground cable from battery. 2) Remove the gear shift knob by turning it counterclockwise. 3) Remove the console box assembly.
More informationHeadlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
More informationPOWER SOURCE (Current Flow Chart)
The chart below shows the route by which current flows from the battery to each electrical source (Fusible Link, Circuit Breaker, Fuse, etc.) and other parts. The next page and following pages show the
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationG ELECTRICAL WIRING ROUTING
G ELECTRICAL WIRING ROUTING Position of Parts in Engine Compartment A 1 A/C Condenser Fan Motor A 2 A/C Magnetic Clutch and Lock Sensor A 3 A/C Triple Pressure SW (A/C Dual and Signal Pressure SW) A 4
More informationPOWER SOURCE (Current Flow Chart)
POWER SOURCE (Current Flow Chart) The chart below shows the route by which current flows from the battery to each electrical source (Fusible Link, Circuit Breaker, Fuse, etc.) and other parts. The next
More informationPROCEDURE STEPS: WARNING:
WI-FI ROUTER 1 DODGE NITRO, JEEP LIBERTY PROCEDURE STEPS: WARNING: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect
More informationL PART NUMBER OF CONNECTORS
L PART NUMBER OF CONNECTORS Code Part Name Part Number Code Part Name Part Number A 1 A/C Ambient Temp. Sensor 90980-11070 B15 Blower Motor Controller (Rear) 90980-11136 A 2 A/C Magnetic Clutch 90980-11271
More informationWait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate Maxima (Applicable ONLY to U.S. Market Vehicles with Build Date June 2012 or later) 999G6
More informationOT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL
More information11.Airbag Warning Light Failure
11.Airbag Warning Light Failure A: AIRBAG WARNING LIGHT REMAINS ON. DIAGNOSIS: Airbag warning light unit is faulty. Airbag control module to airbag warning light circuit is shorted or open. Grounding circuit
More informationBODY (INTERIOR AND EXTERIOR)
BODY (INTERIOR AND EXTERIOR) Return to Main Table of Contents GENERAL... 2 BODY PANELING... 7 HOOD... 12 GRILLE AND MOULDINGS... 14 BUMPER... 16 FENDER... 19 WINDSHIELD... 21 REAR WINDOW GLASS... 25 FRONT
More informationAVALON Hybrid. Gasoline-Electric Hybrid Synergy Drive. AVX40 Series
AVALON Hybrid Gasoline-Electric Hybrid Synergy Drive AVX40 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Toyota AVALON Hybrid gasoline-electric hybrid
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More informationCOMPONENTS Toyota RAV ACCESSORIES & EQUIPMENT Front Seat - RAV4
2005 ACCESSORIES & EQUIPMENT Front Seat - RAV4 COMPONENTS Fig. 1: Identifying Front Seat Components & Torque Specifications FRONT SEAT ASSEMBLY REMOVAL CAUTION: Wear safety gloves, because the cutting
More informationG ELECTRICAL WIRING ROUTING [1MZ-FE] Position of Parts in Engine Compartment
G ELECTRICAL WIRING ROUTING [1MZ-FE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor A 2 A/C Condenser Fan Motor A 3 A/C Magnetic Clutch and Lock Sensor A 4 A/C Triple Pressure SW
More informationGround Circuit. (TURBO AND STi MODEL) B 3 B 4 REARVIEW MIRROR LH (WITH MIRROR HEATER) F17 CRUISE CONTROL MODULE F101 B94 POWER WINDOW RELAY F22 B225
. A: IRING DIAGRAM IRING SYSTEM GND-0 SU FAN MOTOR (TURO AND STi MODEL) F MAIN FAN MOTOR (NON-TURO MODEL) MAIN FAN MOTOR (TURO AND STi MODEL) HEADLIGHT LH LO-EAM (HID MODEL) HEADLIGHT RH LO-EAM (HID MODEL)
More informationTO INDEX LIGHTING SIDE TURN SIGNAL LIGHT ASSEMBLY LH TAILLIGHT (REAR COMBINATION LIGHT) ASSEMBLY LH LICENSE PLATE LIGHT ASSEMBLY
TO INDEX BODY AND ELECTRICAL GHTING GHTING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... BASIC INSPECTION..........................................
More informationAudi A4 Current Flow Diagram No. 64 / 1 Edition
Sivu 1/7 Audi A4 Current Flow Diagram No. 64 / 1 Edition 04.2006 Headlight for gaseous discharge light (Xenon, plus), dynamic cornering lights and automatic headlight range control from August 2004 Notes:
More informationIS300h. Gasoline-Electric Hybrid Synergy Drive. AVE30 Series
IS300h Gasoline-Electric Hybrid Synergy Drive AVE30 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Lexus IS300h gasoline-electric hybrid vehicles. IS300h
More informationOVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
More informationDISPOSAL. CAUTION: Never dispose of front seat outer belt which has an inactivated. activated pretensioner.
DISPOSAL When scrapping vehicles epuipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner) always first active the seat belt pretensioner in accordance
More informationMUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1
2005-2011 MUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1 Thank you for purchasing our 2005-2011 Mustang Tiger Cage. Please read through all of the instructions first and then start installing the kit. We
More informationSECTION 1 6 INSTRUMENTS AND CONTROLS. Comfort adjustment. Front seat... 42
SECTION 1 6 INSTRUMENTS AND CONTROLS Comfort adjustment Front seat................................................ 42 Headrests............................................... 44 Tilt and telescopic steering
More informationTrim Panel: Service and Repair. Garnish Molding Replacement - Center Pillar
2004 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Copyright 2013, ALLDATA 10.52 Page 1 Trim Panel: Service and Repair Garnish Molding Replacement - Center Pillar Garnish Molding Replacement - Center Pillar
More informationG ELECTRICAL WIRING ROUTING
2 6 G ELECTRICAL WIRING ROUTING Position of Parts in Engine Compartment A1 A/C Front Magnetic Valve A3 A/C Magnetic Clutch A6 A/T Flud Temp. Sensor A7 ABS Actuator A8 ABS Actuator A10 ABS Speed Sensor
More informationBODY (INTERIOR AND EXTERIOR) Return To Main Table of Contents
BODY (INTERIOR AND EXTERIOR) Return To Main Table of Contents GENERAL..... 2 BODY PANELING... 6 BODY DIMENSIONS... 11 HOOD... 16 GRILLE AND MOULDINGS... 18 BUMPER... 20 FENDER... 23 WINDSHIELD... 25 REAR
More informationSECTION 9G INTERIOR TRIM
SECTION 9G INTERIOR TRIM CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationOVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
More informationYear Item Description
Mercury Parts Inventory (1939 1975) www.fordoldpart.com Year Item Description 39 Wiper switch, complete w/ all hardware 39-40 NOS Front Cross Member 40 NOS wiper switch with knob 40 Station wagon rear
More informationRESTRAINT SYSTEM SECTIONRS CONTENTS
RESTRAINT SYSTEM SECTIONRS CONTENTS SEAT BELTS...2 Precautions...2 Front Seat Belt...4 SUPPLEMENTAL RESTRAINT SYSTEM (SRS)...6 Precautions...6 Preparation...7 SRS Configuration...8 Seat Belt Pre-tensioner
More informationBulb Renewal TOP ACCESS COVER
TOP ACCESS COVER To gain access to the headlight units, the top cover must be removed. Unscrew and remove the six fasteners (A). Remove the top cover. After changing the defective bulb, refit the cover,
More informationPosition of Parts in Engine Compartment
[1UZ FE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor E 4 Engine Coolant Temp. Sensor (Water Temp. Sensor A 2 A/C Dual Pressure SW and A/C High Pressure SW (for Cooling Fan)) A
More informationSymptom Suspect Area See page. 11.Ignition Switch 12.Power Source Circuit. Symptom Suspect Area See page
BE2 PROBLEM SYMPTOMS TABLE IGNITION SWITCH: BE18204 Ignition switch is not set to each position. KEY UNLOCK WARNING SWITCH: 11.Ignition Switch 12.Power Source Circuit BE15 Key unlock warning system does
More informationService Bulletin NO. 9 NO. 3
Service Bulletin 04-052 Applies To: 2005 CR-V ALL September 3, 2004 2005 CR-V: PDI and New Model Information This service bulletin gives you the information needed for PDI of the 2005 CR-V. It also describes
More informationBuckle SW Rear RH C 1 Camshaft Position Sensor Camshaft Timing Oil Control Valve RH. Crankshaft Position Sensor
A 1 A/C Ambient Temp. Sensor 90980 11070 A 2 A/C Magnetic Clutch and ock Sensor 90980 11016 A 3 A/C Pressure Sensor 90980 10845 A 4 A/C Solenoid 90980 10901 A 5 ABS & TRAC & VSC Actuator 90980 11451 A
More informationG ELECTRICAL WIRING ROUTING
2 6 G ELECTRICAL WIRING ROUTING [2JZ-GTE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp Sensor A 2 A/C Condensor Fan Motor A 3 A/C Triple Pressure SW (A/C Dual and Single Pressure SW) A
More informationUse the appropriate tool from the KTC trim tool set to avoid damage when removing components.
2010 ivic Special Tools Required Report a problem with this article KT Trim Tool Set SOJTP2014 *vailable through the Honda Tool and Equipment Program; call 888-424-6857 SRS components are located in this
More informationPOWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
More information1993 FD3S Touring Trim Electrical FSM Index/Supplement
1993 FD3S Touring Trim Electrical FSM Index/Supplement Purpose: This is simply a searchable index of connectors that are found in the various 1993 FD3S wiring harnesses. Each entry shows the purpose of
More information2002 Escape Workshop Manual
Page 1 of 6 SECTION 501-10: Seating 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/07/2002 Seat Track Driver Seat Removal WARNING: Always wear safety glasses when repairing
More information2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX
2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX BODY SECTION This service manual has been prepared to provide SUBARU service personnel with the necessary information and data for the correct maintenance
More informationPosition of Parts in Engine Compartment
ELECTRICAL WIRING ROUTING [5S FE] Position of Parts in Engine Compartment A 1 A/C Condenser Fan Motor E 4 Engine Coolant Temp. Sensor (EFI Water Temp. A 2 A/C Magnetic Clutch and Lock Sensor Sensor) A
More information2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems
DESCRIPTION & OPERATION 2004 ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems WARNING: Accidental air bag deployment is possible. Personal injury may result. Read and follow all WARNINGS
More informationGLASS/WINDOWS/MIRRORS
General Description 1. General Description : OMPONENT 1. FIXED GLSS (WGON MODEL) (5) (6) (11) (12) (10) (7) (10) (7) (7) (9) (11) (8) (10) GW-00677 Windshield glass (5) Spring (9) Fastener Dam rubber (6)
More informationINSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA
INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA PARA AIRBAG DE CORTINA I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check the VIN range. 2. Check the TIS Vehicle Inquiry System. Not Covered No further
More informationFUSES & CIRCUIT BREAKERS
FUSES & CIRCUIT BREAKERS FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. INTERIOR FUSE PANEL IDENTIFICATION (1983-88 MODELS) On all models, the fuse panel is located under the
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationG ELECTRICAL WIRING ROUTING [2ZZ GE] Position of Parts in Engine Compartment
G ELECTRICAL WIRING ROUTING [2ZZ GE] Position of Parts in Engine Compartment A 1 A/C Magnetic Clutch A 2 ABS Speed Sensor Front LH A 3 ABS Speed Sensor Front RH A 4 Airbag Sensor Front LH A 5 Airbag Sensor
More informationHEADLIGHT AND TAILLIGHT SYSTEM
BE BODY ELECTRICAL LOCATION E/G Room J/B No. HEAD LH Fuse (w/o Daytime Running Light) HEAD RH Fuse (w/o Daytime Running Light) HEAD LH (UPR) Fuse (w/ Daytime Running Light) HEAD RH (UPR) Fuse (w/ Daytime
More information