BLACK & DECKER HAMMER PLUS DRILL KD900RE, KD900CRE

Transcription

1 PRODUCT DOSSIER BLACK & DECKER HAMMER PLUS DRILL KD900RE, KD900CRE KD900_HD.SAM

2 Contents Section Page Title 1 2 Introduction 2 2 Launch planner 3 3 Special Repair Instruction ATTACHED TO THIS DOSSIER Copy of service parts lists KD900RE KD900CRE Copy of service parts drawings E12175 Copy of service wiring diagram E12317 Copy of special repair information R11135 Copy of repair drawing Page 1

3 Introduction Catalogue number(s) KD900RE, KD900CRE Type number TYPE 1 Description HAMMER PLUS DRILL Blows 0/8700 Capacity Power - Watts Voltage No load motor speed Features Manufacturing plant Service parts warehouse Euro Tech engineer 13 mm 700 W 230 V 1200 RPM Variable speed High torque Reversible Rotary Hammer Action Depth Stop Spennymoor, UK. Perth Avenue, UK. Mike Lenahan Launch planner Launch markets Europe Launch date September 1997 Other markets Date N/a N/a Page 2

4 Special Repair Instruction (R11135) DATE: CAT. NUMBERS: KD900RE, KD900CRE TYPE NUMBER: 01 DESCRIPTION: HAMMER PLUS DRILL NOTE. Only the recommended grease ( ) must be used for repair, which is available in 1Kg containers. It is critical that the gearbox is packed with 100 gms of grease, particularly around the intershaft assembly. 1) CHUCK REMOVAL Refer to repair drawing in product dossier For removal of the chuck, service tool Part No ( Chuck Removal Wedges) item off are required. Position wedges (1) between the rear of the chuck (2) and the shoulder on the output spindle (3), with their angled faces against each other. With the flat end of one wedge positioned against a hard surface, strike the end of the other (4) with a metal hammer until the chuck comes off the taper. 2) CHUCK FITTING. Carefully clean the taper then push the chuck firmly on. By rotating the chuck ring retract the jaws fully, select hammer mode on the drill and use against a piece of wood for a few seconds. Page 3

5 KD900RE KD900CRE 1 TYP E12175 /

6 KD900RE---A TY 1 KD900CRE--A TY ITEM DESCRIPTION PART NO. QTY PRICE VARIANT DESCRIPTION 101 ARMATURE 230V FIELD SWITCH VARIABLE SWITCH CORDSET M-AT-BE-DE-ES-FR-GR-IT 105 CORDSET M-CH-AR-BR-CL 105 CORDSET M-DK-FI-NL-NO-PT-SE 105 CORDSET M-GB-IR-KW 106 PROTECTOR T-KD900CRE 106 PROTECTOR T-KD900RE 107 CORD CLAMP SCREW BRUSH & HOLDER SA SCREW CLAMSHELL GRIP HAMMER MODULE WASHER THRUST BEARING THRUST GEAR SPRING SPINDLE BALL WASHER THRUST BEARING SINTER SEAL CHUCK KEYLESS T-KD900CRE 123 CHUCK T-KD900RE 124 CHUCK KEY T-KD900RE 134 CAPACITOR LEAD LEAD SLIDER CAP HANDLE SA CLAMP SCREW DEPTH STOP BEARING MOUNT SELECTOR O RING PIN BRAND LABEL T-KD900CRE 148 BRAND LABEL T-KD900RE 800 GREASE 1KG SERVICE TOOL CE LPA SOUND PRESSURE DB(A) 92 CE LWA ACOUSTIC POWER DB(A) 105 CE VIBRATION M/S/S 10.3 BLOWS

7 KD900RE---A TY 1 KD900CRE--A TY ITEM DESCRIPTION PART NO. QTY PRICE VARIANT DESCRIPTION CAPACITY 13MM VOLTAGE #1 VOLTS 230 AMPERE #1 AMPS 3.2 INPUT WATTS #1 WATTS 700 OUTPUT WATTS #1 WATTS 445 RPM # FREQUENCY #1 HZ 50 ARMATURE RESISTENCE #1 OHMS 4.0 FIELD RESISTENCE #1 OHMS 3.63

8 KD900RE KD900CRE 1 TYP. CIRCUIT DIAGRAM L FIELD N FIELD CHOKE CHOKE COLOUR KEY ENGLISH FRENCH ITALIAN GERMAN BLACK NOIR NERO SCHWARZ WHITE BLANC BIANCO WEISS BROWN BRUN MARRONE BRAUN BLUE BLEU BLU BLAU RED ROUGE ROSSO ROT YELLOW JAUNE GIALLO GELB.. GREEN VERT VERDE GRUN ORANGE ORANGE ARANCIO ORANGE GREY GRIS GRIGIO GRAU CLEAR KLAR WHITE LEAD FROM PCB BLACK LEAD FROM SWITCH CORDSET BROWN/BLACK LEAD CORDSET BLUE/WHITE LEAD BLACK LEAD TO FIELD TERMINAL No. 2 CAPACITOR LEADS RED LEAD FROM SWITCH BLACK LEAD FROM PCB RED LEAD TO FIELD TERMINAL No.1 E12317 / / 97

9 R11135 CAT. NUMBERS: KD900RE, KD900CRE TYPE NUMBER: 01 NOTE. Only the recommended grease ( ) must be used for repair, which is available in 1Kg containers. It is critical that the gearbox is packed with 100 gms of grease, particularly around the intershaft assembly. 1) CHUCK REMOVAL See repair drawing in product dossier. For removal of the chuck, service tool, item No. 840 Part No ( Chuck Removal Wedges), 2 off are required. Position wedges (1) between the rear of the chuck (2) and the shoulder on the output spindle (3), with their angled faces against each other. With the flat end of one wedge positioned against a hard surface, strike the end of the other with a metal hammer until the chuck comes off the taper. 2) CHUCK FITTING. Carefully clean the taper then push the chuck firmly on. By rotating the chuck ring retract the jaws fully, select hammer mode on the drill and use against a piece of wood for a few seconds. R11135EN.SAM

10 KD900RE KD900CRE 1 TYP Repair Drawing 07 / 97