LandRunner II. Table of Contents. Task Procedures Illustrations. LandRunner. Manual Number: Rev

Transcription

1 II Table of Contents Manual Number: Rev Introduction... 1 Delivery... To The Owner... Warranty... 6 Safety... 7 Operating Instructions Anhydrous Ammonia Operating Instructions Coupler Operation... 0 Parts Emergency Fresh Water Tank Location and Assembly Parts... 1 Parts... Nurse Tank Hitch Parts and Assembly Degree Fold Assembly Left-hand 7 & Degree Fold Assembly Right-hand 7 & Single/Dual Lift and Gauge Wheel Parts... 0 Walking Tandem Lift and Single Hydraulic Gauge Wheel W/Jack Adjust... 0a. Walking Tandem Lift and Gauge Wheel Parts... 1 AAM 70 7 Hub x 1 Spindle... AAM 7 7 Hub x Dual Spindle... Gauge Wheel With Pin Adjust & x 7.0 x 1 Tire & Rim... AM 0 Hub and Spindle Assembly... Hitches... 6 Jack... 7 Hydraulic Gauge Wheel Jack Adjust Parts and Assembly... 9 Tires and Rims... 1 Hydraulics Standard... Hydraulics 10 Degree Fold... 0 Hydraulic Selector Valve... Shanks... 9 Offset Stagger Brackets Row Clamps Super 100 Flex Coulter and Shank Parts Blades... 6 SealPro Disc Sealer Manual Holder... 7 Impellicone and Mounting Hardware... 7 SuperShooter III Distribution... 7 Extension Bracket AAM MaxPac AR700 Parts and Assembly... Torsion Mount Basket Assembly MaxPac AT700 Torsion Arm Basket Mount... 9 Basket Mount Flat With Hardware... 9 Residue Cleaner Parts and Assembly Hydraulic Repair Parts... Tie-rod Cylinder Disassembly-Assembly Procedure... Torque Specifications... 6 Assembly Mainframe and Wing Mounting... 7 Tongue and Jack... Jack Handle and Safety Chain... 9 Hitch, Jack, and Hitch Storage... 1 Nurse Tank Hitch Standard Fold Mounting Degree Fold Mounting Row Spacings Pin Adjust Gauge Wheels Lift and Gauge Wheels Dual Hub and Spindle Dual and Single Mounting Walking Tandem Lift and Gauge Wheels Degree Fold Degree Fold Primary Wing Stop and Lock-down... 1 Offset Stagger Bracket... Shank Mounting Coulter Assembly and Mounting... 1 Standard Fold Hydraulics Standard and 10 Fold Hose Locations... 1 Hydraulic Assembly Continued... SMV and Light Kit Safety Tank... 1 Decal Placement Standard and 10 Degree... 1 Manual Holder Bolt-on Wing Kit Row 0 With Bolt-on Wing Kit

2 Introduction Welcome to Thurston Manufacturing Company. Our goal is to provide quality products and services to our customers. The company s BLU-JET products have a reputation for quality, excellence in design and proven durability. Energetic, resourceful and continuous improvement goals in Environmental, Safety, Quality, Production and Engineering keep our firm at the cutting edge of technology. We hope your BLU-JET equipment will give you years of service. Read this manual carefully. It will instruct you on how to operate and service your machine safely and correctly. Failure to do so could result in personal injury and\or equipment damage. SAFETY INFORMATION DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. The sign will have the color combination of red and white. WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. The sign will have the color combination of orange and black. CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. The sign will have the color combination of yellow and black. NOTE: Indicates a special point of information. Carefully read and follow all safety signs. Reinstall safety signs that are damaged or missing. Right-hand and left-hand sides of the implement are determined by facing in the direction the implement will travel when going forward. Warranty is provided for customers who operate and maintain their equipment as described in this manual. Warranty registration is accomplished by the dealer completing and forwarding the WARRANTY REG- ISTRATION FORM to Thurston Manufacturing Company. It is in your best interest to insure that this has been done.

3 INTRODUCTION For your convenience we have four easy ways to register your warranty. Call our toll free number and ask for warranty registration Fax completed warranty registration form. Fax: 0--0 Register on-line in warranty page at Complete and return registration form. Thurston Manufacturing Company Warranty does not cover the following: 1) Cleaning, transporting, mailing and service call charges. ) Depreciation or damage caused by normal wear, accidents, improper protection or improper use. See complete Warranty for details. The Serial Number is located from the rear of the tool bar on the right-hand side behind the tongue pull plate. Serial Number Record your implement model and serial number in the space provided below. Your dealer needs this information to give you prompt, efficient service when you order parts. MODEL NO. SERIAL NO. DATE PURCHASED

4 DEALER CHECKLIST To The Dealer: Inspect the implement thoroughly after assembly to be certain it is functioning properly before delivering it to the customer. The following checklist is a reminder of points to cover. Check off each item as it is found satisfactory or after proper adjustment is made. PRE-DELIVERY CHECKLIST 1. All hardware properly tightened. Lubrication of grease fittings. All decals properly located and readable. Other adjustments for machine level height, etc.. Overall condition (touch up any scratches, clean and polish) 6. Operator's manual DATE SET UP SIGNATURE DELIVERY Review the operator's manual with the customer. Explain the following: 1. Safe operation and service. Correct machine installation and operation. Daily and periodic lubrication and maintenance Daily and periodic inspections. Trouble shooting 6. Storing machine 7. Thurston Manufacturing Company parts and service. Have the customer write the machine model and serial number in space provided in manual introduction. 9. Give customer the operator's manual and encourage the customer to read the manual carefully.. Completion and mailing of warranty registration form. DATE DELIVERED SIGNATURE MODEL NO. SERIAL NO.

5 To The Owner Thank you for your recent purchase of a new BLU-JET implement. The primary objective of Thurston Manufacturing Company is to build and provide you with a quality product. However, in the event that a problem does occur, it is imperative that your warranty registration is on file in order to accurately respond to your specific service circumstances. For your convenience we have four easy ways to register your warranty: Register Warranty One of Four Ways Call our toll free number and ask for warranty registration Fax your completed warranty registration form Register on-line at: Complete and mail the warranty registration form. This manual has been prepared to assist you in the assembly of your new machine and contains information pertaining to safety, operations and all of its parts. Our personnel in sales and service are always available to assist you when questions arise concerning the assembly or operations of your tool bar. When ordering parts, please refer to part numbers and descriptions as listed throughout this book. All parts and whole goods will be shipped FOB Thurston, Nebraska. Or FOB your regional distributor. Always check merchandise immediately upon receipt for damage or shortage. Note any discrepancy on carrier's bill of lading and notify Sender within days. Returned goods will be subject to a 1% restocking charge. Thurston Manufacturing Company reserves the right to make improvements and modifications on equipment without obligation to change previously built equipment. All prices are subject to change without notice.

6 Limited Warranty Thurston Manufacturing Company warrants each new BLU-JET machine primary framework to be free from defects in material and workmanship for a period of five () years, normal wear of wearing parts excepted. Thurston Manufacturing Company further warrants each new BLU-JET product to be free from defects in material and workmanship, normal wear of wearing parts excepted, for a period of one (1) year. All accessories purchased and resold by Thurston Manufacturing Company will be warranted according to their respective manufacturer. Tires on BLU-JET equipment are warranted through their respective tire manufacturers and their network of dealers in your local area. Warranty begins from date of delivery to the original purchaser and applies to all new BLU-JET products that have not been altered and are being used for the intended purpose. Negligence, abuse or modification of equipment manufactured by or purchased and resold by Thurston Manufacturing Company will void this warranty. The obligation of Thurston Manufacturing Company to honor this warranty is limited to the repair or replacement of defective merchandise, to the original purchaser, subject to inspection of equipment in question by an authorized Thurston Manufacturing Company sales or service technician. In the USA, freight of warranty replacement parts including main frame centers and wings will be prepaid for a period of one (1) Year by Thurston Manufacturing Company. Shipments of repaired or replaced parts including main frame centers and wings after one year will be paid by the customer. Return of defective goods must be made within thirty (0) days of failure to Thurston Manufacturing Company, Thurston, Nebraska USA or to the nearest authorized BLU-JET Distributor or Rep Sales and service outlet. Thurston Manufacturing Company will not be held responsible for any repair charges made by customers without prior written consent and prior equipment inspection by an authorized Thurston Manufacturing Company sales or service technician. This warranty shall not be interpreted to render liability for injury or damages of any kind, direct, consequential or contingent to person or property. This warranty does not extend to loss of crops, economic and/or commercial loss, loss because of delay in crop production or any expense incurred for labor, supplies, substitute machinery, rental or for any other reason. This warranty is subject to any existing condition of supply, which may directly affect Thurston Manufacturing Company s ability to obtain materials of manufacture and delivery of replacement parts. Thurston Manufacturing Company reserves the right to make improvements in design and changes in specifications at any time without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor its exclusions, limitations and reservations. Thurston Manufacturing Company makes no representations or warranties, expressed or implied (including implied warranties of merchantability and fitness), except for those set forth in Thurston Manufacturing Company s current applicable published warranty policies and procedures. Layton W. Jensen, President 09\mgmt 6

7 Safety RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see his symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. FOLLOW SAFETY INSTRUCTIONS Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in good condition. Replace missing or damaged safety sign. Learn how to operate the machine and how to use controls properly. Do not let anyone operate machine without instruction. Keep your machine in proper working condition. Unauthorized modification to the machine may impair the function and\or safety and affect machine life PROTECT CHILDREN AND BYSTANDERS Before you back, LOOK CAREFULLY behind for children. Clear area of children, pets and bystanders. HIGHWAY AND TRANSPORT OPERATIONS Adopt safe driving practices: Keep the brake pedals latched together at all times. NEVER USE INDEPENDENT BRAKING WITH MACHINE IN TOW AS LOSS OF CONTROL AND/OR UPSET OF UNIT CAN RESULT. Always drive at a safe speed relative to local conditions and ensure that your speed is low enough for a emergency stop to be safe and secure. Keep speed to a minimum. Reduce speed prior to turns to avoid the risk of overturning. Avoid sudden uphill turns on steep slopes. Always keep the tractor or towing vehicle in gear to provide engine braking when going downhill. Do not coast. Do not drink and drive. Comply with state and local laws governing highway safety and movement of farm machinery on public roads. Use approved accessory lighting and necessary warning devices to protect operators of other vehicles on the highway during daylight and nighttime transport. The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use. Local laws should be checked for all highway lighting and marking requirements. When driving the tractor and equipment on the road or highway, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem. 7

8 Safety HIGHWAY AND TRANSPORT OPERATIONS Plan your route to avoid heavy traffic. Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersection, etc. Be observant of bridge loading ratings. Do not cross bridges rated lower than the gross weight at which you are operating. Always operate equipment in a position to provide maximum visibility at all times. Makes allowances for increased length and weight of the equipment when making turns, stopping the unit, etc. TRANSPORT SAFETY A safety chain will help control drawn equipment should it accidentally separate from the drawbar. Attach the chain to the tractor drawbar support or other anchor location. Provide only enough slack in the chain to permit turning. Use hydraulic cylinder transport lockup during road transportation. Maximum road speed is 0 m.p.h. AVOID HIGH PRESSURE FLUIDS Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids. If an accident occurs, see a doctor immediately. DISPOSE OF FLUIDS PROPERLY Improperly disposing of fluids can harm the environment and ecology. Before draining any fluids, contact your local environmental agency for the proper waste disposal methods. Use proper container when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them. DO NOT pour oil into the ground, down a drain, or into a stream, pond, or lake. Observe relevant environmental protection regulations when disposing of oil and other harmful waste.

9 Safety Observe Safety Signs AP -7-9 AP 91 AP --9 AP -90 AP

10 Safety Decals AP 97 AP 97 AP 7 AP 97 AP 97

11 Operating Instructions Hitch 1. The tractor must be equipped with a drawbar and a drawbar safety chain clevis. For rigid frame tractors equipped NOTE: Implement hitch weights are designed to match tractor size ranges. Check the following chart to confirm your particular implement specification. with swinging drawbar, the drawbar must be located in a fixed position in the center of the tractor. Refer to your tractor operators manual for drawbar adjustment and drawbar operating instructions. Generic Photo Category Engine HP Range Drawbar Vertical Load Pounds I ,0 II 0 1 1,6,97 III 0 7,,97 IV 10 00,777,1 Tractor to tool bar connection Safety hitch pin Safety chain. Before connecting the tool bar to the tractor drawbar, raise the tractor three point hitch (if equipped) to prevent interference between the implement and the tractor. Connect the tool bar to tractor drawbar ONLY. DO NOT connect the tool bar to any other part of the tractor. Connect the tool bar clevis to the tractor drawbar with hitch pin. Install the safety chain through the tractor drawbar support bracket.. Always use a safety hitch pin of the correct diameter. Make sure that the hitch pin is locked in place with a safety type lock pin or other locking device.. Always use a safety chain between the toolbar and the tractor. Install the chain to the tractor drawbar support bracket. Support the center of the chain with a clevis installed to the tractor drawbar. WARNING: In case the tractor hitch pin is lost during transporting. The safety chain must be attached between the implement and tractor to prevent separated implement from running freely and causing damage or injury. WARNING: Do not move articulated tractor steering wheel until everyone is clear of the equipment. Moving the steering wheel can swing or move attached equipment which could cause serious personal injury. WARNING: Tractor drawbar must be in a fixed position before transporting implement. Implement will sway or slam against tractor resulting in equipment damage or injury to personnel. 11

12 Operating Instructions Remote hydraulic NOTE: Always connect the hoses so the toolbar raises when the tractor remote control lever is moved rearward and lowers when the lever is moved forward.. Connect the toolbar hydraulic hoses to the tractor remote couplers. The /" hoses supply oil to the toolbar lift cylinders. The 1/" hoses supply oil to the wing fold cylinders. WARNING: Hydraulic fluid escaping under pressure can have enough force to penetrate the skin. Hydraulic fluid may also infect a minor cut or opening in the skin. If injured by escaping fluid, see doctor at once. Serious infection or reaction can result if medical treatment is not given immediately. Make sure all connections are tight and that hoses and lines are in good condition before applying pressure to the system. Relieve all pressure before disconnecting the lines or performing other work on the hydraulic systems. Remote hydraulic 6. It may be necessary to tie the hydraulic hoses up to keep them away from the hitch area. A tarp strap around the hoses and between the two point arms works well. Leveling mainframe 7. Before leveling the machine tire pressure should be checked. Inflate mainframe tires to: Inflate 11L-1, Ply, tire 6 psi. Max. Inflate 11L-1, 1 Ply, tire psi. Max. Before beginning operation of this machine the main frame must be level. Place toolbar on level surface. Adjust the hitch up or down in the tongue connector and connect to tractor. 1 Jack stand. Jack Stand (unhitching) Pull ring on drop leg jack plunger and lower sand pad to ground. Secure plunger in holes before cranking jack to the ground. IMPORTANT: Always lower the jack stand to the ground before disconnecting the tool bar from the tractor. Ring

13 Operating Instructions Attaching electrical harness 9. Attach 7 pin electrical harness before road transport. Hydraulic gauge wheel. Leveling Hydraulic Gauge Wheel Check tire pressure before leveling toolbar. Hydraulic gauge wheels do not require depth collars. Additional leveling can be accomplished with tire air pressure or installation of optional hydraulic gauge wheel jack adjust kit. (Bundle Number 79) Lift wheel depth collars NOTE: Unequal depth collar installation may result in unequal depth control of knives. NOTE: Toolbars with Liquid or Dual Placement hydraulic systems require a hydraulic cylinder spacer on the " slave cylinder. See hydraulic section for details. 11. Install equal lengths of cylinder depth collars to the right and left-hand center section wheel lift cylinders. This will provide equal depth of knives Depth Collars 1

14 Operating Instructions Nurse tank hitch NOTE: Periodically check Latch mechanism to ensure proper latching in the extended position. 1. Nurse tank hitch can be retracted and moved from side to side for easy hookup. Hitch will automatically lock in the extended position. WARNING Pinch point To prevent Injury Keep hands clear when extending or retracting the swing slide insert Oil Flow Restricter 1. Hydraulic wing cylinders are designed with oil flow restricter fittings to provide a smooth and even folding sequence. Oil flow restricter modification may negatively affect the folding performance. The oil flow restricters slow the wing operation for maximum safety. Oil Flow Restricter Cylinder rod maintenance 1. All exposed cylinder rods should be greased before seasonal storage to prevent rusting. Remove depth collars and lubricate exposed cylinder rods. 1

15 Operating Instructions Lubricating wing hinges 1. Unfold wings and grease all wing hinges daily. NOTE: Grease all zerks daily. Wheel leg lubrication 16. Grease wheel leg daily. Coulter pivot shaft lubrication 17. Grease all coulter arm pivots. Coulter hub lubrication 1. The plug on the coulter hub can be removed. A zerk can be installed. Hub and spindle assembly should be greased twice seasonally. Emergency water tank operation and maintenance 19. Location of nine-gallon emergency water tank/ toolbox. Change water daily to provide fresh clean water to flush exposed skin or eyes. Drain water daily in cold temperatures to prevent freezing and bursting tank. 0. In case of exposure to fertilizer, open faucet or pull top end of hose loose to flush exposed part of body. Remove contaminated clothes as soon as possible. 1

16 Operating Instructions Lug Nut Torque 1. Lug nut Torque 1. Check every hour first four hours.. Check every four hours to first twenty hours.. Check once every fifty hours thereafter. Lubrication. Lubrication Grease all zerks daily Grease coulters daily Gauge Wheel Pivot Zerk Zerks On Wing Hinges Zerks On Top Of Hinges Zerk Under Hitch Lift Wheel Pivot Zerk On Wing Gauge Wheels (Torque 7- ft./lbs.) On Center Section Wheels (Torque 7- ft./lbs.) Generic Diagram 16

17 Anhydrous Ammonia Operating Instructions Attend Anhydrous Ammonia Safety Training Class Provided By Your Dealer Before Operating this equipment. Operator protection Because of the hazards associated with handling Anhydrous Ammonia, operators must use proper protective equipment. Minimum equipment includes tight-fitting chemicalproof goggles, long cuff rubber gloves, heavy-duty long sleeved shirt. In case of exposure, have a minimum of gal`s of flushing water available at all times. Body Guard Tank Connection Break Away NOTE: A light application of oil maybe applied to the break away coupler mating Checking System With personal protective equipment in place, visually inspect the tool bar and system components for integrity, includes hoses that may be subject to inadvertent contact with structural surfaces resulting in premature exterior hose deterioration. Hooking Up Nurse Tank With personal protective equipment in place, hitch the nurse tank to the tool bar using a keyed hitch pin. Affix wagon tongue safety chains securely to Nurse tank chain loops provided. Carefully hand tighten the nurse tank supply hose connection. Position hose to allow unobstructed movement in case of Nurse Tank break away. Do not allow supply hose to contact surfaces that may cause abrasion or wear including sharp corners, soil or roads. With personal protective equipment in place, confirm the functional operation of the break away coupler on a daily basis. First bleed pressure off of tank supply hose and 1-1/" quick coupler using the bleed valves provided. Sharply pull on the tank supply hose. The coupler mechanism should release under these forces. Visually inspect coupler for corrosion, foreign elements and proper seating of mating poppets. DO NOT transport equipment from field to field with tank and supply line valves open. When immediately ready for field application, beginning at the tank, and with personal protective equipment in place, slowly open all supply line valves. WARNING: Position your body away from the bleed valve exit hole to avoid contact with Anhydrous Ammonia when bleed valve is opened. Contact with skin will cause severe chemical burns. WARNING: Avoid breathing ammonia vapors. Clear all personnel from the area before opening system. Inhalation of vapors will irritate or damage respiratory tract and lungs, resulting in injury or death. Bleed Valve 17

18 Anhydrous Ammonia Operating Instructions Disconnection Of Nurse Tank 1. With personal protective equipment in place, and beginning at the tank, fully shut off the supply hose valves. If the supply hose is a tank wagon component (as opposed to a tool bar component) an additional hand operated globe valve shut off located between the quick coupler and the Heat Exchanger feed line will significantly speed up the tank wagon change process.. Clear all personnel from area except for the operator. While considering the direction of the wind to avoid ammonia vapor drift toward the operator or any other personnel, beginning at the tank, slowly open supply line bleed valves to release pressure from the hose.. Physically grasp, lift and lightly shake the supply hose mid section to insure total evacuation of ammonia. Once again, be wary of the wind direction.. Place the supply hose in a transport storage position, preventing it from becoming entangled or in contact with sharp edges or abrasive surfaces.. Always park and unhook the nurse tank on a smooth and level surface. Block the wheels to prevent tank wagon runaway. High winds or uneven terrain can cause unblocked tank wagons to move out of control. 6. Disconnect tank wagon tongue safety chains, hitch pin key and hitch pin. CAUTION: Fifth wheel style running gear front axles may inadvertently rotate in uneven soil conditions when the hitch pin is pulled causing the tongue to come into contact and potentially injuring the operator. WARNING: Before maintenance is preformed on any part of the NH system, be sure the total system is bled off and all liquid is drained. Liquid ammonia can remain trapped in system cavities, even when the system has been opened to atmospheric pressure. Always assume that ammonia remains in the system components and hoses at all times. Always wear tight-fitting chemical-proof goggles, long cuff rubber gloves, heavy-duty long sleeved shirt and exercise extreme caution. 1

19 Safety Decals AP 97 AP 97 AP 7 AP 97 AP 97 19

20 Coupler Operations Coupler release handle A NOTE: Read coupler operation decal (AP 97) for safety instructions Female coupler Male coupler neck Body Guard III Feed-line to tank Coupler bleed valve B C D E Male coupler half F Check valve plunger Connecting DANGER: Always wear protective gear G 1. Stand on the upwind side. Close all feed-line valves and inspect all components for proper condition.. Relieve pressure in nurse tank hose between male coupler (F) and first shutoff valve towards nurse tank by carefully opening coupler bleed valve (E). The Squibb Flo-Max coupler is designed to re-couple safely with pressure on the female coupler half (B). CAUTION: Leave coupler bleed valve (E) open for now. DANGER: Avoid breathing ammonia vapors DANGER: Hazardous chemical under pressure. While holding and pointing the hose and male coupler (F) downwind and away from your person, depress check valve plunger (G) with gloved finger to ensure proper operation. Wipe foreign debris from coupler neck (C) with clean cloth.. Make certain BodyGuard III TM (D) is installed fully with slot oriented around check valve plunger (G) to protect against ammonia spray-back during coupling.. Insert male coupler neck (C) into female coupler half (B) as far as possible. Then, while applying insertion pressure, pull downward on coupler release handle (A) to complete the coupling process. Release handle (A) after engagement of coupler neck (C). 6. Lightly pull on male coupler (F) to ensure proper engagement. 7. Close bleed valve (E) and others if open. Open tank and hose valves just prior to applying ammonia. Disconnect 1. After closing all valves, bleed pressure from male coupler half (F) by opening coupler bleed valve (E). Leave bleed valve (E) open. 0. Then, pull down on coupler release handle (A) and remove male coupler half (F).

21 Emergency Fresh Water Tank Location and Assembly Location of Nine-gallon emergency water tank/toolbox. Change water daily to provide fresh clean water to flush exposed skin or eyes. Drain water daily in cold temperatures to prevent freezing and bursting tank. In case of exposure to anhydrous ammonia, open faucet or pull top end of hose loose to flush exposed part of body. Remove contaminated clothes as soon as possible. Seek medical attention. Ref. Part No. Req. Description 1. AM 16 Bracket, tank mounting, 9 gallon. AP 17 1 Tank, 9 gallon freash water safety. AP 1 1 Decal, BLU-JET, x. BP 001 Nut, hex, / -16, grade, plated. BP 00 Washer, lock, /, plated 6. BP 6 Hex cap screw, /16-1 x 1, grade, plated 7. BP 1 U-bolt, / -16 x -1/16 x 7, plated. BP 1 6 Washer, lock, /16, plated 9. BP 19 6 Washer, flat, /16, plated

22 LR II 7 (1'6" Center 6'" Primary Wings) Ref. Part No. Req. Description 1. AAM 09 1 SMV Kit, "x 6" 1a. AM Bracket, SMV Mounting 1b. AP 1 SMV Mounting Socket 1c. BP 001 Hex Nut, /-16, Grade, Plated 1d. BP 00 Lock Washer, /, Plated 1e. BP 0 1 U-Bolt, /-16 x 6" x ", Plated. AAM 1 Transport chain Kit, 0,000 # a. AP 19 1 Transport chain, 0,000#, 7/16 b. AP 69 1 Decal, Safety Chain c. BM 9 1 Bushing, safety chain 1-/ OD x 1.1 ID x d. BP 01 1 Pin, 1 x 6, hitch. plated e. BP 11 1 Pin, cotter, /16 x 1-/. AAM 1 Safety Tank, Toolbox a. AP 1 1 Decal, BLU-JET, x b. BP 1 U-bolt, / -16 x -1/16 x 7 LT hose T, plate PKG0000 c. AM 16 Bracket, tank mounting, 9 gallon d. AP 17 1 Tank, 9 gallon, Fresh Water Safety e. BP 001 Nut, hex, / -16, grade, plated f. BP 00 Washer, lock, /, plated g. BP 6 Hex cap screw, /16-1 x 1, grade, plated h. BP 1 6 Washer, lock, /16, plated i. BP 19 6 Washer, flat, /16, plated. AAM 69 1 Manual Holder w/ 6 x a. AM Bracket, mounting, manual holder b. AP 1 Manual holder, Black, 01-1 c. BP 001 Nut, hex, / -16, grade, plated d. BP 00 Washer, lock, /, plated, c. BP Hex cap screw, / -16 x 1, grade, plated d. BP 0 1 U-bolt, / -16 x 6 x, plated. AM 090 Bracket, Depth Collar & Lockup Storage 6. AM 1 1 Jack, 9TW DL TMC Blue 7. AM 6 1 Crank W/Grip, 90 0, Long, Blue. AM 0 Bolt-On Primary Wing Stop 9. AM Rocker Plate, LR/LW, New Style 0/0. AM 1 Primary Wing, 6 -, LH w/down Flex 11. AM 6 1 Primary Wing, 6 -, RH w/down Flex 1. AM 9 1 Tongue, LR II, RH, Weighted 1. AM 9 1 Tongue, LRll LH, Weighted 1. AM 9 1 Frame, LR II, 1 6 StripTill Center Section 1. AM 9 1 Tongue connector, LR II StripTill Frame Ref. Part No. Req. Description 16. AP 06 Decal, 17. AP 1 Decal, BLU-JET, " x ", 1. AP 16 Decal, BLU-JET, Small, 1-1/" x " 19. AP 1 Decal, Warning Stand Clear of Tongue 0. AP 1 Decal, Limited Warranty, -1/" x 9-1/" (Discontinued) 1. AP 1 1 Decal, FEMA, -1/" x 1-1/". AP Decal, Danger Stand Clear Falling Wing. AP -1 Hose Retainer, " x 6". AP 1 Decal, Danger Falling From Equipment AP 6 1 Paint, Spray Can, Blue1 oz AP 69 1 Paint, Spray Can, Black 1 oz. AP 711 Snap Ring, 1-1/ External, Heavy Duty 6. AP 1 Electrical Harness, 1 7. AP 91 1 Decal, Warning, High Pressure Fluid. BM Pin, 1-1/ x -/ Plated, Useable, Double Grooved 9. BM 60 Pin, 1-/" x 1-/" Usable, Anti-rotation Hook 0. BP 001 Hex Nut, /-16, Grade, Plated 1. BP 00 Lock Washer, /", Plated. BP 00 1 Hex Lock Nut, /-16, Grade, Plated. BP 01 Flat Washer, /, Plated. BP 0 Hex Nut, /-, Grade, Plated. BP 0 Lock Washer, /, Plated 6. BP 0 Hex Nut, /-11, Grade, Plated 7. BP 09 Lock Washer, /", Plated. BP 0 U-Bolt, /-16 x 6"x ", Plated 9. BP 01 Pin, 1"x 6", Hitch, Plated 0. BP 07 Grease Zerk, 1/- 1. BP Hex Cap Screw, /-16 x -1/", Grade, Plated. BP 099 U-Bolt, /-11 x 6" x 6", Plated. BP 1 Hex Cap Screw, /- x -1/", Grade, Plated. BP 11 1 Hex Cap Screw, /- x ", Grade, Plated. BP 0 U-Bolt, /- x 6"W x -/"L, Plated 6. BP 9 Machinery Bushing, 1-7/ OD x 1-1/ ID, 1 GA 7. BP 11 Pin, Cotter, /16" x 1- /". BP 19 Pin, Roll, /" x -1/", Plain 9. DP 06 Cable Tie, 11-/ Standard 0. DP 96 1 Cable Tie, Optional Hitch 1. AM 1 1 Clevis Hitch. AP 0 1 Perfect Hitch CAT. III. AP 6 1 Perfect Hitch CAT. IV

23 LR II 7 (1'6" Center 6'" Primary Wings) 1b 1a d 1c 9 1c 1d c b d c e c 17 9 d c d a d Elec,Extension Harness (AP ) for pull type implements 1 6 g h i 17 c d c e a 19 1 b b 6 f e g h i d a 1

24 LR II 1 (1'6" Center '7" Primary Wings) Ref. Part No. Req. Description 1. AAM 09 1 SMV Kit, "x 6" 1a. AM Bracket, SMV Mounting 1b. AP 1 SMV Mounting Socket 1c. BP 001 Hex Nut, /-16, Grade, Plated 1d. BP 00 Lock Washer, /, Plated 1e. BP 0 1 U-Bolt, /-16 x 6" x ", Plated. AAM 1 Transport chain Kit, 0,000 # a. AP 19 1 Transport chain, 0,000#, 7/16 b. AP 69 1 Decal, Safety Chain c. BM 9 1 Bushing, safety chain 1-/ OD x 1.1 ID x d. BP 01 1 Pin, 1 x 6, hitch. plated e. BP 11 1 Pin, cotter, /16 x 1-/. AAM 1 Safety Tank, Toolbox a. AP 1 1 Decal, BLU-JET, x b. BP 1 U-bolt, / -16 x -1/16 x 7 LT hose T, plate PKG0000 c. AM 16 Bracket, tank mounting, 9 gallon d. AP 17 1 Tank, 9 gallon, Fresh Water Safety e. BP 001 Nut, hex, / -16, grade, plated f. BP 00 Washer, lock, /, plated g. BP 6 Hex cap screw, /16-1 x 1, grade, plated h. BP 1 6 Washer, lock, /16, plated i. BP 19 6 Washer, flat, /16, plated. AAM 69 1 Manual Holder w/ 6 x a. AM Bracket, mounting, manual holder b. AP 1 Manual holder, Black, 01-1 c. BP 001 Nut, hex, / -16, grade, plated d. BP 00 Washer, lock, /, plated, c. BP Hex cap screw, / -16 x 1, grade, plated d. BP 0 1 U-bolt, / -16 x 6 x, plated. AM 090 Bracket, Depth Collar & Lockup Storage 6. AM 1 1 Jack, 9TW DL TMC Blue 7. AM 6 1 Crank W/Grip, 90 0, Long, Blue. AM 0 Bolt-On Primary Wing Stop 9. AM Rocker Plate, LR/LW, New Style 0/0. AM 1 1 Primary Wing, -7, LH w/down Flex 11. AM 1 Primary Wing, -7, RH w/down Flex 1. AM 9 1 Tongue, LR II, RH, Weighted 1. AM 9 1 Tongue, LRll LH, Weighted 1. AM 9 1 Frame, LR II, 1 6 StripTill Center Section 1. AM 9 1 Tongue connector, LR II StripTill Frame Ref. Part No. Req. Description 16. AP 06 Decal, 17. AP 1 Decal, BLU-JET, " x ", 1. AP 16 Decal, BLU-JET, Small, 1-1/" x " 19. AP 1 Decal, Warning Stand Clear of Tongue 0. AP 1 Decal, Limited Warranty, -1/" x 9-1/" (Discontinued) 1. AP 1 1 Decal, FEMA, -1/" x 1-1/". AP Decal, Danger Stand Clear Falling Wing. AP -1 Hose Retainer, " x 6". AP 1 Decal, Danger Falling From Equipment AP 6 1 Paint, Spray Can, Blue1 oz AP 69 1 Paint, Spray Can, Black 1 oz. AP 711 Snap Ring, 1-1/ External, Heavy Duty 6. AP 1 Electrical Harness, 1 7. AP 91 1 Decal, Warning, High Pressure Fluid. BM Pin, 1-1/ x -/ Plated, Useable, Double Grooved 9. BM 60 Pin, 1-/" x 1-/" Usable, Anti-rotation Hook 0. BP 001 Hex Nut, /-16, Grade, Plated 1. BP 00 Lock Washer, /", Plated. BP 00 1 Hex Lock Nut, /-16, Grade, Plated. BP 01 Flat Washer, /, Plated. BP 0 Hex Nut, /-, Grade, Plated. BP 0 Lock Washer, /, Plated 6. BP 0 Hex Nut, /-11, Grade, Plated 7. BP 09 Lock Washer, /", Plated. BP 0 U-Bolt, /-16 x 6"x ", Plated 9. BP 01 Pin, 1"x 6", Hitch, Plated 0. BP 07 Grease Zerk, 1/- 1. BP Hex Cap Screw, /-16 x -1/", Grade, Plated. BP 099 U-Bolt, /-11 x 6" x 6", Plated. BP 1 Hex Cap Screw, /- x -1/", Grade, Plated. BP 11 1 Hex Cap Screw, /- x ", Grade, Plated. BP 0 U-Bolt, /- x 6"W x -/"L, Plated 6. BP 9 Machinery Bushing, 1-7/ OD x 1-1/ ID, 1 GA 7. BP 11 Pin, Cotter, /16" x 1- /". BP 19 Pin, Roll, /" x -1/", Plain 9. DP 06 Cable Tie, 11-/ Standard 0. DP 96 1 Cable Tie, Optional Hitch 1. AM 1 1 Clevis Hitch. AP 0 1 Perfect Hitch CAT. III. AP 6 1 Perfect Hitch CAT. IV

25 LR II 1 (1'6" Center '7" Primary Wings) 1d 1c c c 1b 1a c 1d b d c 0 1e c 17 9 d d a d Elec,Extension Harness (AP ) for pull type implements 1 6 g h i c 6 d c e a 19 1 b b 6 f e g h i d a 1

26 Nurse Tank Hitch Parts & Assembly Ref. Part No. Req. Description AAM 6 Hitch Assembly, Swing-Slide 1. AM 0 1 Hitch Nurse Tank Main Frame AT000. AM 1 Hitch Swing Slide Insert, Standard a. AP16 Nylon Bushing, 1-1/" OD, x 1-1/" ID, 1-1/" OAL. AM 1 Hitch, Flipper, Standard Mtg. Nurse Tank Hitch. AM 1 SuperShooter Mounting, Nurse Tank Hitch. AM 9 1 Safety Latch 6. AM 0 1 Backing Plate Safety Chain Loop, Standard Nurse Tank 7. AM 1 1 Safety Chain Hook, Standard Nurse Tank, 96. AP 711 Snap Ring, 1-1/" External, Heavy Duty 9. BM 1 Pin, 1-1/" x -/" Plated Useable, Double Grooved. BM 9 1 Pin, 1-1/" x -/16" Usable Grooved W/Anti-Rotation 11. BM 0 1 Pin, 1-/" x 1-1/16" Useable, Grooved W/Head 1. BP 00 1 Nut, Hex Lock, /-16 Grade Plated 1. BP Hex Cap Screw, /-16 x 1" Grade Plated 1. BP 07 1 Nut, Hex Lock, /-, Grade, Plated 1. BP 01 Hex Cap Screw, 1/-1 x Grade Plated 16. BP 0 Nut, Hex, 1/-1, Grade Plated 17. BP 0 Washer, Lock 1/" Plated 1. BP 07 1 Grease Zerk, 1/- 19. BP 16 1 Hex Cap Screw, /- x 6" Grade Plated 0. BP 19 Machinery Bushing, 1-7/" OD x 1-1/" ID x Gauge. 1. BP 0 1 Machinery Bushing, -1/" x 1-/", Gauge. BP 0 1 Snap Ring, 1-/" External. BP 9 1 Machinery Bushing, 1-1/" ID x 1-7/" OD. 1 Gauge. BP 7 Grease Zerk, 1/-, 6 Degree AAM 66 1 Hitch Assembly, AAM 6 1 Hitch Assembly, Swing-Slide. AM 96 1 Brace, Nurse Tank Hitch, LR II 6. BP 0 Nut, Hex, /"-, grade, plated 7. BP 0 Washer, Lock, /", plated. BP Hex cap screw, /"- x -1/", grade, plated 6

27 Nurse Tank Hitch Parts & Assembly Generic Frame

28 10 Degree Fold Assembly Left-hand a Ref. Req. Part No. Description 1 1 AM 1 Wing, 7, primary, left-hand w/ down flex 1 AM 00 Cylinder lug, LR, 10 fold AM 0 Hinge, LR, 10 fold 1 AM 0 Wing,, LR, 10 fold a. 1 AM 0 Wing,, LR, 10 Fold 1 AM Rocker plate, LR, 10 fold 6 1 AM 9 Wing rest and latch LR 10 fold 7 1 AM 1 Secondary wing linkage, #1 1 AM 16 Secondary wing linkage, # 9 1 AM 66 Wing latch pivot, secondary wing 1 AM 67 Pipe spacer 11 AM 6 Secondary wing lock plate 1 AP 07 Snap ring, 1 external, heavy duty 1 AP 711 Snap Ring, 1-1/ external, heavy duty 1 BM 1 Pin, 1-1/ x 7-/16 with groove 1 1 BM Pin, 1 x -/ with groove 16 1 BM Pin, 1 x -/16, double groove, plated 17 BP 0 Nut, hex, / -, grade, plated 1 BP 0 Washer, lock, /, plated 19 BP 0 Nut, hex, / -11, grade, plated 0 BP 09 Washer, lock, /, plated 1 BP 099 U-bolt, / -11 x 6 x 6, plated BP 16 Hex cap screw, / - x 6, grade, plated 1 BP 179 Hex cap screw, 1/ -1 x, grade, plated BP 0 U-bolt, / - x 6 x -/, plated BP 1 Machinery bushing, 1-1/ OD x 1 ID, 1 gauge 6 1 BP Nut, hex lock, 1/ -1, plated 7 BP 9 Machinery bushing, 1-7/ OD x 1-1/ ID, 1 gauge 1 BP 09 Pin, 1-1/ x -/ 9 1 BP 17 Lynch pin, 7/16

29 10 Degree Fold Assembly Right-hand a Ref. Req. Part No. Description 1 1 AM Wing, 7, primary, right-hand w/down flex 1 AM 00 Cylinder lug, LR, 10 fold AM 0 Hinge, LR, 10 fold 1 AM 0 Wing,, LR, 10 fold a. 1 AM 0 Wing,, LR, 10 Fold 1 AM Rocker plate, LR, 10 fold 6 1 AM 9 Wing rest & latch, LR 10 fold 7 1 AM 1 Secondary wing linkage, #1 1 AM 16 Secondary wing linkage, # 9 1 AM 66 Wing latch pivot, secondary wing 1 AM 67 Pipe spacer 11 AM 6 Secondary wing lock plate 1 AP 07 Snap ring, 1 external, heavy duty 1 AP 711 Snap Ring, 1-1/ external, heavy duty 1 BM 1 Pin, 1-1/ x 7-/16 with groove 1 1 BM Pin, 1 x -/ with groove 16 1 BM Pin, 1 x -/16, double groove, plated 17 BP 0 Nut, hex, / -, grade, plated 1 BP 0 Washer, lock, /, plated 19 BP 0 Nut, hex, / -11, grade, plated 0 BP 09 Washer, lock, /, plated 1 BP 099 U-bolt, / -11 x 6 x 6, plated BP 16 Hex cap screw, / - x 6, grade, plated 1 BP 179 Hex cap screw, 1/ -1 x, grade, plated BP 0 U-bolt, / - x 6 x -/, plated BP 1 Machinery bushing, 1-1/ OD x 1 ID, 1 gauge 6 1 BP Nut, hex lock, 1/ -1, plated 7 BP 9 Machinery bushing, 1-7/ OD x 1-1/ ID, 1 gauge 1 BP 09 Pin, 1-1/ x -/ 9 1 BP 17 Lynch pin, 7/16 9

30 Single/Dual Lift and Gauge Wheel Bundle Numbers: 707 (Wheel lift singles) 70 (Wheel lift duals) a a 1 1 Ref. Part No. Req. Description 1. AAM 70 1 Assembly, Hub & Spindle, 7 Hub, "x 1" 1a. AAM 7 1 Assembly, Hub & Spindle, 7 Hub, "x ". AM 07 1 Bracket, Cylinder Upright, LH.. AM 0 1 Bracket, Cylinder Upright, RH.. AM 09 1 Bracket, Cylinder Upright Clamp.. AM 0 1 Wheel Leg, " Spindle Loop. 6. BM 1 Pin, 1-/"x 11-11/16" Usable W/AntiRotation 7. BP 0 Machinery Bushing, -1/"x 1-/", GA.. BP 7 6 Nut, Hex, 1-, Grd., Pltd. 9. BP 90 6 Hex Cap Screw, 1- x ", Grd., Pltd.. BP 16 Tension Bushing 1-1/"x 1" ID x 1" OAL 11. BP 19 1 Pin, Roll, /"x -1/", Plain 1. BP 079 Set Screw, Sq Head, /-11 x 1-/", Unpltd 1. BP 00 Nut, Hex Jam, /-11 Quantities shown are for one lift or gauge wheel. 0

31 Walking Tandem Lift and Gauge Wheel 9 Bundle Numbers: 711 Wheel lift walkers w/ walking tandem hydraulic gauge wheels) 796 (Wheel lift walkers w/pin adjust manual gauge wheels) Right-hand Walker Ref. Part No. Req. Description 1. AAM 70 Assembly, Hub & Spindle, 7 Hub, " x 1". AM 6 Cylinder, Upright. AM 0 Pivot Pin, Tandem, ". AM 00 Heavy Duty Wheel Leg Deluxe Walker, " Spindle. AM 99 Walker Left-Hand LRII 6. AM 9 Walker Right-Hand LRII 7. AM 0 Plate, Deluxe Walker Stop (Gauge Wheels Only). AM 07 Bracket, Pivot Arm Heavy Duty 9. AM 09 Bracket, Cylinder Upright Clamp, Black. BP 0 16 Nut, Hex, /"-, Grd., Plated. 11. BP 0 16 Washer, Lock, /", Pltd. 1. BP 07 6 Grease Zerk, 1/"- 1. BP 16 Hex Cap Screw, /"- x -1/", Grd., Plated. 1. BP 16 Tension Bushing, 1-1/" x 1" ID x 1", Oal 1. BP 7 Nut, Hex, 1"-, Grd., Plated 16. BP 90 Hex Cap Screw, 1"- x ", Grd., Plated 1

32 (AAM 70) 7 Hub x 1 Spindle Ref. Part No. Req. Description 1. AP 0 1 Bearing Cone, LM 670. AP 0 1 Nut, Spindle, 7/ -1. AP 0 1 Hub Cap, 11. AP 09 6 Wheel Bolt, 1/ -0 x 1. AP 0 1 Bearing Cone, LM AP 0 1 Grease Seal, CR 1 7. AP 10 1 Hub With/Cups, 6 Bolt, 6 BC,.6 Pilot, 7 Hub. AP 17 1 Spindle, x 1 S71-I AP 6 Pin, Cotter, / X 1-/. AP 7 Washer, Spindle, x 1/16 x.16

33 (AAM 7) 7 Hub x Dual Spindle Ref. Part No. Req. Description 1. AP 0 Bearing cone, LM 670. AP 0 Nut, spindle, 7/ -1. AP 0 Hub cap, 11. AP 09 1 Wheel bolt, 1/ -0 x 1. AP 0 Bearing cone, LM AP 0 Grease seal, CR 1 7. AP 10 Hub with/cups, 6 bolt, 6 BC,.6 pilot, 7 hub. AP Spindle, C x DE, with countersunk holes 9. AP 6 Pin, cotter, / X 1-/. AP 7 Washer, spindle, x 1/16 x.16

34 Gauge Wheel With Pin Adjust & x 7.0 x 1 Tire & Rim Tractor side of tool bar Ref. Part No. Req. Description 1. AAM 76 Wheel x 7.0-1, ply 1 x 6 x 6 White. AM 0 ST II Gauge Wheel Leg Assembly. AM 0 ST II Gauge Wheel Tool Bar Mount Assembly. AP 07 Snap Ring 1" External Heavy Duty. BM 60 ST II Gauge Wheel Leg Pivot Pin 6. BP 0 Hex Nut /" - Plated 7. BP 01 Pin-1" x 6 1/". BP 1 1" 1Ga. Machine Bushing 9. BP 0 U-Bolt /"- x 6W x -/ L Plated. BP 11 /16" x 1-/" Cotter Key

35 AM 0 Hub and Spindle Assembly Ref. Part No. Req. Description 1. AP 0 1 Bearing cone, LM 670. AP 0 1 Hub, Cap, 11. AP 09 6 Wheel bolt, 1/ -0. AP Grease seal, CR 169. AP 07 1 Bearing cone, JL AP 1 1 Hub with/cup, 6 bolt, AP 16 1 Washer, spindle, x 1-1/16 x.1. AP 6 1 Pin, cotter, / x 1-/ 9. AP 11 1 Nut, spindle, 1-1. EM Weldment, gauge wheel leg, pin adjust

36 Hitches 1 e d a b c a Ref. Part No. Req. Description 1. AM 1 1 Fabricated Truck Hitch. AP 6 1 Cat. IV Heat Treated Cast Wheatland Hitch HP " Pin a. AP 0 1 Cat. III Heat Treated Cast Wheatland Hitch 1-0 HP 1-1/" Pin Optional. AAM 1 Bracket, Second Hitch Storage a. AM 1 1 Bracket, Hitch Storage b. BP 001 Nut, Hex, / -16 Grd. Pltd. c. BP00 Washer, Lock, /", Pltd. d. BP 0 1 U-bolt, / -16 x 6"x ", Pltd. e. BP 00 1 Pin, Hair Clip, /16" 6

37 9TW- DL Top wind DL Jack Ref. Part No. Req. Description Assy AM 1 9TW- DL Topwind DL Jack 1. AM 1 Intermediate Tube With Plunger 1 SW. AM 1 Dropleg With Pad & Handle 1 SW DL. AM 1 Screw Assembly " for 9TW-1. AM 9 1 Top With/ Bolt On Mounting " SD0F. AP 07 1 Snap Ring 1" Ring 1" External Heavy Duty 6. AP 1 Thrust Bearing Nice BP 00 1 Hex Nut Lock /"-16 Gd. Plated. BP 01 Flat Washer /" Plated 9. BP Hex Cap Screw /"-16 x 1/" Gd. Plated. EM "-1/" x 1.0 ID x 1/" Bearing Seat Purchased 11. EM 179 1/" CRR x 9/16 DL Jack Nut Retainer 1. EM # Jack Label 1. AM 6 1 Handle With Grip (Not included with jack assembly.) NOTE: Handle not included in AM1 assembly. 7

38 Hydraulic Gauge Wheel Jack Adjust Hydraulic gauge wheel jack adjust parts Bundle Number: Ref. Part No. Req. Description 1. AM 1 Bracket, knuckle. AM 0 Bracket, ratchet jack. AP 96 Jack, implement, adjustable, TL1--. BP 0 Nut, hex, / -, grade, plated. BP 0 Washer, lock, / plated 6. BP 07 U-bolt, / - x W x 7-/, plated 7. BP 0 6 Pin, clevis, 1 x -/ useable. BP 11 1 Pin, cotter, /16 x 1-/ 9. BP 16 Tension bushing, 1-1/ x 1 x 1 OAL NOTE: Four (BP 176) / - x -1/ hex cap screws are included with parts. The / x -1/ hex cap screw will replace the u-bolts if a stagger bracket aligns with the wheel leg upright. The hex cap screw will be inserted through the stagger bracket into the jack bracket and secured with the / lock washers and / hex nuts.

39 Hydraulic Gauge Wheel Jack Adjust Mounting adjustable gauge wheel CAUTION To Prevent Serious Injury: Install with provided hardware only. 1. Unfold toolbar wings and lower machine.. Relieve the pressure on the cylinder pins.. Remove the top cylinder pin. Installing knuckle bracket. Position (1) (AM 1) knuckle bracket on wheel leg upright and secure with (7) (BP 0) clevis pin 1 x -/ and () (BP 11) cotter pins /16 x 1-/.. Install (9) (BP 16) 1-1/ x 1 x 1 tension bushing in bottom hole of knuckle bracket. Jack bracket parts 6.. AM 0 (1) Bracket, jack. BP 0 () Hex nut, / -. BP 0 () Washer, lock / 6. BP 07 () U-bolt, / - x W x 7-/ plated 6 9

40 Hydraulic Gauge Wheel Jack Adjust Assembly Mounting jack bracket 7. Position the () (AM 0) ratchet jack attachment bracket on front tube of the wing. Install (6) (BP 07) / x W x 7-/ u-bolts, () (BP 0) / lock washers and () (BP 0) / hex nuts. Align the bracket with the wheel leg and tighten hex nuts. The cylinder weldment is mounted to the top with walkers. tension bushing Walkers Singles and Duals The cylinder weldment is mounted to the bottom with singles and duals.. Install (9) (BP 16) 1-1/ x 1 x 1 tension bushing in cylinder weldment. Tension bushing Attaching adjustable implement jack 9. Mount () (AP 96) adjustable implement jack with (7) (BP 0) clevis pin 1 x -/ and () (BP 11) cotter pins /16 x 1-/. Attaching cylinder to knuckle bracket NOTE: Retact jack before charging cylinders.. Reattach cylinder to knuckle bracket. 11. Retract jack before charging cylinders on new assembly. 0

41 Tires & Rims (LRII) A 1 Ref.Part No. Req. Description A. AAM 77 - Wheel 11L-1, Ply 1. AP 01 1 Tire, 11L-1, Ply, Tubeless. AP Rim, 1"x "x White. AP Valve Stem 11L-1, Ply, Single, Duals & Walkers Inflate 11L-1, Ply, tire 6 psi. Max. Max speed m.p.h. A 1 Ref.Part No. Req. Description A. AAM 76 - Wheel 11L-1, 1 Ply 1. AP 01 1 Tire, 11L-1, 1 Ply, Tubeless. AP Rim, 1"x "x 6" White. AP Valve Stem 11L-1, 1 Ply Duals & Walkers Inflate 11L-1, 1 Ply, tire psi. Max. Max speed m.p.h. 1

42 Hydraulics NH Only w/manual Gauge Wheels Bundle Number Flow Restrictor G Primary Wing 1 Cylinder A B C Primary Wing Cylinder -1/" X 1" Lift Cylinder 9 1 D E D -1/" X 1" Lift Cylinder 1 NOTE: Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder Ref. Part No. Req. Description 1. AM 09 Transport Cylinder Lock. AM 9 Bolt-On Wing Spacer. BM 0 Clip Pin Transport Lock /16". BM Oil Flow Restrictor. BP 01 Hex Cap Screw 1/-1 x " Grd, Pltd 6. BP 0 Hex Nut 1/-1, Grd, Pltd 7. BP 0 Lock Washer 1/" Pltd. BP 00 Flat Washer 1/" Pltd 9. BP 076 Depth Collar Set, 1-1/" to 1-1/" Winged. DP 001 Male Elbow MJ-MP Adapter 11. DP 00 1 Tee 6MJ-6MJ-6MJ 1. DP 1 Adapter 90 0 MJIC-MSAE Male Elbow 1. DP 161 Adapter O-Ring MSAE- FP 1. DP 1-1/"x 1" Rephase Cylinder PMS-AM DP 1-1/"x 1" Rephase Cylinder PMS-AM DP 6 Hydraulic Cylinder "x " (,000) PSI, SAE-0 DP 06 Cable Tie 11-/" Standard DP 96 Cable Tie " DDP 0 1 Hose Kit LRII Standard A. DP /"x '-6" 6FJX-6FJX B. DP 0 1 1/"x 6'-0" 6FJX-6FJX C. DP 06 1 /"x 11'-0" FJX-FJX D. DP 090 /"x 1'-0" FJX-MP E. DP 0 1 1/"x '-0" MP-MP F. DP /"x '-0" MP-6FJX G. DP /"x '-0" 6FJX-6FJX Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

43 Bundle Number 700 Hydraulics Liquid Or Dual Placement w/manaual Gauge Wheels Flow Restrictor Primary Wing Cylinder A B G 1 1 C 19 1 Primary Wing Cylinder /" X 1" Lift Cylinder D 1 " X 1" Lift Cylinder E 1 D F Ref. Part No. Req. Description 1. AM 09 1 Transport Cylinder Lock. AM 9 Bolt-On Wing Spacer. AM 71 1 Extra Heavy Duty Cylinder Lock-Up. BM 0 Clip Pin Transport Lock /16". BM Oil Flow Restrictor 6. BP 01 Hex Cap Screw 1/-1 x " Grd, Pltd 7. BP 0 Hex Nut 1/-1, Grd, Pltd. BP 0 Lock Washer 1/" Pltd 9. BP 00 Flat Washer 1/" Pltd. BP Depth Collar Set 1-1/" to 1-1/" Winged Extra Heavy Duty Depth Collar 11. BP 1 1 " Extra Heavy Duty Depth Collar DP 001 Male Elbow MJ-MP Adapter 1. DP 00 1 Tee 6MJ-6MJ-6MJ 1. DP 1 Adapter 90 0 MJIC-MSAE Male Elbow NOTE: Tape all pipe thread fittings only. It is not 1. DP 161 Adapter O-Ring MSAE- FP 16. DP 6 1 " x 1" Rephase Cylinder PMS-AM- necessary to tape the J.I.C. flare fittings. 17. DP 7 1-1/"x 1" Rephase Cylinder PMS-AM-6 1. DP 6 Hydraulic Cylinder " x "(,000 PSI) SAE-0 CAUTION: Do not overtighten pipe 19. EM /" I.D. x " O.D. Aluminium Hyd. Cylinder Spacer threaded fittings. This may damage the cylinder. DP 06 Cable Tie 11-/" Standard DP 96 Cable Tie 17 1 DDP 0 1 Hose Kit LRII Standard A. DP /"x '-6" 6FJX-6FJX B. DP 0 1 1/"x 6'-0" 6FJX-6FJX C. DP 06 1 /"x 11'-0" FJX-FJX D. DP 090 /"x 1'-0" FJX-MP E. DP 0 1 1/"x '-0" MP-MP F. DP /"x '-0" MP-6FJX G. DP /"x -'0" 6FJX-6FJX Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

44 Hydraulics NH Only With Hydraulic Gauge Wheels Bundle Number Flow Restrictor Primary Wing Cylinder C A 6 1 B 7 D 11 -/" X 1" Lift Cylinder J E I H Primary Wing Cylinder " X 1" Lift Cylinder 7 9-1/" X 1" Gauge Wheel Cylinder G 7-1/" X 1" Gauge Wheel Cylinder Ref. Part No. Req. Description 1. AM 09 Transport Cylinder Lock. BM 0 Clip Pin Transport Lock /16" 1 CRR x 1". BM Oil Flow Restrictor. BP 076 Depth Collar Set 1-1/" to 1-1/" Winged. DP 001 Male Elbow 90 Degree 6MJ-MP Adapter 6. DP 00 1 Tee 6MJ-6MJ-6MJ 7. DP 1 Adapter 90 Degree MJIC-MSAE Male Elbow. DP 161 Adapter O-Ring MSAE-FP 9. DP 1-1/" x 1" Rephase Cylinder PMS-AM-70. DP 1-1/" x 1" Rephase Cylinder PMS-AM DP 1 -/" x 1" DA Rephase Cylinder PMS-AM- 1 F 1. DP 6 1 " x 1" DA Rephase Cylinder PMS-AM- 1. DP 6 Hydraulic Cylinder " x " (000) PSI SAE-0 DP 06 Cable Tie 11 /" Standard DP 96 Cable Tie " DDP 1 1 Hose Kit LRII With Hydraulic Gauge Wheel A DP 0 1 1/" x 9'0" 6FJX-6FJX Ends B DP /" x 6'6" 6FJX-6FJX Ends C DP 07 1 /" x 1'6" FJX Ends D DP 06 1 /" x 11' 0" FJX Ends E DP /" x '0" MP-6FJX Ends F DP 07 1 /" x 1' 0" FJX Ends G DP /" x ' 0" FJX-MP Ends H DP /" x 1'0" FJX-MP Ends NOTE: Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder. Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

45 Hydraulics Liquid Or Dual With Hydraulic Gauge Wheels Bundle Number 706 Flow Restrictor " x " Primary Wing Cylinder C A 1 B 7 9 D 1 " X 1" Lift Cylinder J 7 16 E I H 9 1 " X " Primary Wing Cylinder 6 1-1/" X 1" Lift Cylinder /" X 1 Gauge Wheel Cylinder G 9 1 -/" x 1" Gauge Wheel Cylinder Ref. PMS-AM- Part No. Req. Description 1. AM 09 1 Transport Cylinder Lock. AM 71 1 Heavy Duty Cylinder Lock-Up. BM 0 Clip Pin Transport Lock /16" 1 CRR x 1". BM Oil Flow Restrictor. BP Depth Collar Set 1-1/" to 1-1/" Winged 6. BP 1 1 Depth Collar Set, 1-/" to ", Winged 7. DP 001 Male Elbow 90 Degree 6MJ-MP Adapter. DP 00 1 Tee 6MJ-6MJ-6MJ 9. DP 1 Adapter 90* MJIC-MSAE Male Elbow. DP 161 Adapter O-Ring MSAE -FP 11. DP 1-1/" x 1" Rephase Cylinder PMS-AM-6 1. DP 1 -/" x 1" DA Rephase Cylinder PMS-AM- 1. DP 6 1 " x 1" DA Rephase Cylinder 1 F 1. DP 7 1-1/" x 1" DA Rephase Cylinder PMS-AM-6 1. DP 6 Hydraulic Cylinder " x " (000) PSI SAE EM697 1 /16" Hydraulic Cylinder Spacer DP 06 Cable Tie 11 /" Standard DP 96 Cable Tie " DDP 1 1 Hose Kit LRII With Hydraulic Gauge Wheel A DP 0 1 1/" x 9'0" 6FJX-6FJX Ends B DP /" x 6'6" 6FJX-6FJX Ends C DP 07 1 /" x 1'6" FJX Ends D DP 06 1 /" x 11' 0" FJX Ends E DP /" x '0" MP-6FJX Ends F DP 07 1 /" x 1' 0" FJX Ends G DP /" x ' 0" FJX-MP Ends H DP /" x 1'0" FJX-MP Ends I DP 0 1 1/" x '0" MP Ends J DP /" x ' 0" 6FJX Ends NOTE:Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder. Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

46 Hydraulics NH w/ Hydraulic Gauge Wheel Bundle Number 76 Flow Restrictor G Primary Wing 1 Cylinder A B C Primary Wing Cylinder -1/" X 1" Lift Cylinder 9 1 D E D -1/" X 1" Lift Cylinder 1 NOTE: Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder Ref. Part No. Req. Description 1. AM 09 Transport Cylinder Lock. AM 9 Bolt-On Wing Spacer. BM 0 Clip Pin Transport Lock /16". BM Oil Flow Restrictor. BP 01 Hex Cap Screw 1/-1 x " Grd, Pltd 6. BP 0 Hex Nut 1/-1, Grd, Pltd 7. BP 0 Lock Washer 1/" Pltd. BP 00 Flat Washer 1/" Pltd 9. BP /" to 1-1/" Winged Depth Collar Set. DP 001 Male Elbow MJ-MP Adapter 11. DP 00 1 Tee 6MJ-6MJ-6MJ 1. DP 1 Adapter 90 0 MJIC-MSAE Male Elbow 1. DP 161 Adapter O-Ring MSAE- FP 1. DP 1-1/"x 1" Rephase Cylinder PMS-AM DP 1-1/"x 1" Rephase Cylinder PMS-AM DP Hydraulic Cylinder "x " (,000) PSI SAE-0 DP 06 Cable Tie 11-/" Standard DP 96 Cable Tie " DDP 0 1 Hose Kit LRII Standard A. DP /"x '-6" 6FJX-6FJX B. DP 0 1 1/"x 6'-0" 6FJX-6FJX C. DP 06 1 /"x 11'-0" FJX-FJX D. DP 090 /"x 1'-0" FJX-MP E. DP 0 1 1/"x '-0" MP-MP F. DP /"x '-0" MP-6FJX G. DP /"x '-0" 6FJX-6FJX 6 Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

47 Hydraulics NH Only With Hydraulic Gauge Wheels LR Bundle Number 77 1 Flow Restrictor Primary Wing Cylinder C A 6 1 B 7 D 11 -/" X 1" Lift Cylinder J E I H Primary Wing Cylinder " X 1" Lift Cylinder 7 9-1/" X 1" Gauge Wheel Cylinder G 7-1/" X 1" Gauge Wheel Cylinder Ref. Part No. Req. Description 1. AM 09 Transport Cylinder Lock. BM 0 Clip Pin Transport Lock /16" 1 CRR x 1". BM Oil Flow Restrictor. BP /" to 1-1/" Winged Depth Collar Set. DP 001 Male Elbow 90 Degree 6MJ-MP Adapter 6. DP 00 1 Tee 6MJ-6MJ-6MJ 7. DP 1 Adapter 90 Degree MJIC-MSAE Male Elbow. DP 161 Adapter O-Ring MSAE-FP 9. DP 1-1/" x 1" Rephase Cylinder PMS-AM-70. DP 1-1/" x 1" Rephase Cylinder PMS-AM DP 1 -/" x 1" DA Rephase Cylinder PMS-AM- 1. DP 6 1 " x 1" DA Rephase Cylinder PMS-AM- 1 F 1. DP Hydraulic Cylinder " x " (000) PSI DP 06 Cable Tie 11 /" Standard DP 96 Cable Tie " DDP 1 1 Hose Kit LRII With Hydraulic Gauge Wheel A DP 0 1 1/" x 9'0" 6FJX-6FJX Ends B DP /" x 6'6" 6FJX-6FJX Ends C DP 07 1 /" x 1'6" FJX Ends D DP 06 1 /" x 11' 0" FJX Ends E DP /" x '0" MP-6FJX Ends F DP 07 1 /" x 1' 0" FJX Ends G DP /" x ' 0" FJX-MP Ends H DP /" x 1'0" FJX-MP Ends I DP 0 1 1/" x '0" MP Ends J DP /" x ' 0" 6FJX Ends NOTE:Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder. Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x " 7

48 Hydraulics Liquid Or Dual Placement w/manual Gauge Wheel Bundle Number 7 Flow Restrictor 1 1 Primary Wing Cylinder NOTE: Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder A B G 1 1 C " X 1" Lift Cylinder 19 D E D F Primary Wing Cylinder 1 11 Ref. Part No. Req. Description 1. AM 09 1 Transport Cylinder Lock. AM 9 Bolt-On Wing Spacer. AM 71 1 Extra Heavy Duty Cylinder Lock-Up. BM 0 Clip Pin Transport Lock /16". BM Oil Flow Restrictor 6. BP 01 Hex Cap Screw 1/-1 x " Grd, Pltd 7. BP 0 Hex Nut 1/-1, Grd, Pltd. BP 0 Lock Washer 1/" Pltd 9. BP 00 Flat Washer 1/" Pltd. BP /" to 1-1/" Depth Collar Set Extra Heavy Duty Depth Collar 11. BP /" to " Extra Heavy Duty Depth Collar 1. DP 001 Male Elbow MJ-MP Adapter 1. DP 00 1 Tee 6MJ-6MJ-6MJ 1. DP 1 Adapter 90 0 MJIC-MSAE Male Elbow 1. DP 161 Adapter O-Ring MSAE- FP 16. DP 6 1 " x 1" Rephase Cylinder PMS-AM- 17. DP 7 1-1/"x 1" Rephase Cylinder PMS-AM-6 1. DP Hydraulic Cylinder " x " (,000 PSI) SAE EM /" I.D. x " O.D. Aluminium Hyd. Cylinder Spacer DP 06 Cable Tie 11-/" Standard DP 96 Cable Tie " 1-1/" X 1" 17 1 DDP 0 1 Hose Kit LRII Standard A. DP /"x '-6" 6FJX-6FJX B. DP 0 1 1/"x 6'-0" 6FJX-6FJX C. DP 06 1 /"x 11'-0" FJX-FJX D. DP 090 /"x 1'-0" FJX-MP E. DP 0 1 1/"x '-0" MP-MP F. DP /"x '-0" MP-6FJX G. DP /"x -'0" 6FJX-6FJX Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x "

49 Hydraulics Liquid Or Dual With Hydraulic Gauge Wheels Bundle Number Flow Restrictor Primary Wing Cylinder C 7 A 1 7 Primary B Wing Cylinder 9 D 1 " X 1" Lift Cylinder J 7 16 E I H /" X 1" Lift Cylinder /" X 1 Gauge Wheel Cylinder G 9 1 -/" x 1" Gauge Wheel Cylinder Ref. Part No. Req. Description 1. AM 09 1 Transport Cylinder Lock. AM 71 1 Heavy Duty Cylinder Lock-Up. BM 0 Clip Pin Transport Lock /16" 1 CRR x 1". BM Oil Flow Restrictor. BP /" to 1-1/" Depth Collar Set Winged 6. BP /" to " Extra Heavy Duty Depth Collar 7. DP 001 Male Elbow 90 Degree 6MJ-MP Adapter. DP 00 1 Tee 6MJ-6MJ-6MJ 9. DP 1 Adapter 90* MJIC-MSAE Male Elbow. DP 161 Adapter O-Ring MSAE -FP 11. DP 1-1/" x 1" Rephase Cylinder PMS-AM-6 1. DP 1 -/" x 1" DA Rephase Cylinder PMS-AM- 1. DP 6 1 " x 1" DA Rephase Cylinder PMS-AM- 1 F 1. DP 7 1-1/" x 1" DA Rephase Cylinder PMS-AM-6 1. DP Hydraulic Cylinder " x " (000) PSI SAE EM697 1 /16" Hydraulic Cylinder Spacer DP 06 Cable Tie 11 /" Standard DP 96 Cable Tie " DDP 1 1 Hose Kit LRII With Hydraulic Gauge Wheel A DP 0 1 1/" x 9'0" 6FJX-6FJX Ends B DP /" x 6'6" 6FJX-6FJX Ends C DP 07 1 /" x 1'6" FJX Ends D DP 06 1 /" x 11' 0" FJX Ends E DP /" x '0" MP-6FJX Ends F DP 07 1 /" x 1' 0" FJX Ends G DP /" x ' 0" FJX-MP Ends H DP /" x 1'0" FJX-MP Ends I DP 0 1 1/" x '0" MP Ends J DP /" x ' 0" 6FJX Ends NOTE: Tape all pipe thread fittings only. It is not necessary to tape the J.I.C. flare fittings. CAUTION: Do not overtighten pipe threaded fittings. This may damage the cylinder. Ref. Part No. Req. Description 1. AM 0 1 Bracket, cylinder lug, LR/LW STANDARD FOLD. AM 1 Frame, main, LR II, 1'6" center. BP 0 Nut, hex /"-11. BP 09 Washer, lock /". BP 171 Hex cap screw, /"-11 x " 9

50 Hydraulics 1 LRII Cylinders 10 Degree Fold Bundle Number

51 Bundle Number 791 Hydraulics 1 LRII Cylinders 10 Degree Fold Ref. Part No. Req. Description 1. AM 09 Transport cylinder lock. AM 1 1 Bracket, cylinder lug, cylinder, LR/LW 10 degree fold. BM 0 Clip pin, transport lock, /16" x 1". BP 0 Nut, hex, / -11, grade, plated. BP 09 Washer, lock, /, plated 6. BP 076 Depth collar set, 1-/, heavy duty 7. BP 171 Hex cap screw, / -11 x, grade, plated. BP 70 Tension bushing, 1-1/ x 1 x 1 9. DP 00 1 Tee, 6MJ-6MJ-6MJ. DP 1 Adapter, MIJ-MSAE, 90 degree 11. DP 11 Tee, side, 6MJ-6MJ M, O-Ring 1. DP Cylinder, hydraulic " x ", 000 psi, SAE W/Adapters 1. DP 01 Adapter, 6MJ-MSAE, 90 degree 1. DP 7 Cylinder, hydraulic, x 0, 000 psi, SAE DP 9 1 Adapter, MSAE-6MJIC DP 1 Cylinder, rephase, -1/ x 1, PMS-AM DP 1 Cylinder, rephase, -1/ x 1, PMS-AM-6 1. DP 1 Cylinder, rephase, -/ x 1, PMS-AM- 19. DP 6 1 Cylinder, rephase, x 1, PMS-AM- DP 06 Cable tie, 11-/", standard DP 96 Cable tie, " DDP 16 1 Hose kit, LRII deluxe fold, 0. DP 0 1 Hose, hydraulic, 1/ x 66 ( 6 ), 6FJX-6FJX 1. DP 06 1 Hose, hydraulic, / x 1 (11 ), FJX-FJX. DP 07 Hose, hydraulic, 1/ x 10 ( ), 6FJX-6FJX. DP 07 1 Hose, hydraulic, 1/ x 7 (6 6 ), 6FJX-6FJX. DP 07 1 Hose, hydraulic, / x 16 (1 6 ), FJX-FJX. DP 07 1 Hose, hydraulic, / x 7 (1 ), FJX-FJX 6. DP 09 Hose, hydraulic, 1/ x 6 ( ), MP-6FJX 7. DP Hose, hydraulic, / x (1 ), FJX-MP. DP Hose, hydraulic, / x ( ) JX-MP 9. DP Hose, hydraulic, 1/ x 90 (7 6 ), 6FJX-6FJX 1

52 Hydraulics 1 LRII Cylinders 10 Degree Fold Bundle Number

53 Hydraulics 1 LRII Cylinders 10 Degree Fold Bundle Number 7916 Ref. Part No. Req. Description 1. AM 09 1 Transport cylinder lock. AM 1 1 Bracket, cylinder lug, cylinder, LR/LW 10 degree fold. AM 71 1 Transport lock, heavy duty, 1-/ x cylinder rod. BM 0 Clip pin, transport lock, /16" x 1". BP 0 Nut, hex, / -11, grade, plated 6. BP 09 Washer, lock, / plated 7. BP Depth collar set, 1-/, heavy duty. BP 171 Hex cap screw, / -11 x, grade, plated 9. BP 1 1 Depth collar set,, extra heavy duty. BP 70 Tension bushing, 1-1/ x 1 x DP 00 1 Tee, 6MJ-6MJ-6MJ 1. DP 1 Adapter, MJIC-MSAE, 90 degree 1. DP 11 Tee, side, 6MJ-6MJ-M, O-Ring 1. DP Cylinder, hydraulic " x ", 000 psi, SAE w/adapters 1. DP 01 Adapter, 6MJ-MSAE, 90 degree, DP 7 Cylinder, hydraulic, x 0, 000 psi, SAE DP 9 1 Adapter, MSAE-6MJIC DP 1 Cylinder, rephase, -1/ x 1, PMS-AM DP 1 Cylinder, rephase, -/ x 1, PMS-AM- 0. DP 6 1 Cylinder, rephase, x 1, PMS-AM- 1. DP 7 1 Cylinder, rephase, -1/ x 1 PMS-AM-6 DP 06 Cable tie, 11-/", standard DP 96 Cable tie, " DDP 16 1 Hose kit, LRII deluxe fold, shoemaker 99. DP 0 1 Hose, hydraulic, 1/ x 66 ( 6 ), 6FJX-6FJX. DP 06 1 Hose, hydraulic, / x 1 (11 ), FJX-FJX. DP 07 Hose, hydraulic, 1/ x 10 ( ), 6FJX-6FJX. DP 07 1 Hose, hydraulic, 1/ x 7 (6 6 ), 6FJX-6FJX 6. DP 07 1 Hose, hydraulic, / x 16 (1 6 ), FJX-FJX 7. DP 07 1 Hose, hydraulic, / x 7 (1 ), FJX-FJX. DP 09 Hose, hydraulic, 1/ x 6 ( ), MP-6FJX 9. DP Hose, hydraulic, / x (1 ), FJX-MP 0. DP Hose, hydraulic, / x ( ), FJX-MP 1. DP Hose, hydraulic, 1/ x 90 (7 6 ), 6FJX-6FJX. EM / ID x OD aluminum x 1-/16 hydraulic cylinder spacer

54 Hydraulics 1 LRII -1/ Cylinders 10 Degree Fold Bundle Number

55 Hydraulics 1 LRII -1/ Cylinders 10 Degree Fold Bundle Number 7917 Ref. Part No. Req. Description 1. AM 09 1 Mounting bracket divider combiner. AM 09 Transport cylinder lock. AM 1 Bracket, cylinder lug, -1/ cylinder, LR/LW 10 degree fold. BM 0 Clip pin, transport lock /16" x 1". BP Nut, hex, /"-16, grade, plated 6. BP 00 Washer, lock, /, plated 7. BP 01 Washer, flat, /, plated. BP 0 Nut, hex, / -11, grade, plated 9. BP 09 Washer, lock, /, plated. BP 0 1 U-bolt, / -16 x 6" x ", plated 11. BP 076 Depth collar set, 1-/ heavy duty 1. BP 096 Hex cap screw, / -16 x -1/, grade, plated 1. BP 171 Hex cap screw, / -11 x, grade, plated 1. BP 60 Tension bushing, 1-1/ x 1-1/ x 1 1. DP 1 Adapter, MJ-MP, 90 degree male elbow 16. DP 11 Tee, side, 6MJ-6MJ M, O-Ring 17. DP 01 6 Adapter, 6MJ-MSAE, 90 degree 1. DP 7 Cylinder, hydraulic, x 0, 000 psi, SAE DP 9 Adapter, MSAE-6MJIC DP 1 Cylinder, hydraulic -1/" x ", 000 psi, SAE w/adapters 1. DP 1 Cylinder, rephase, -1/ x 1, PMS-AM-70. DP 1 Cylinder, rephase, -1/ x 1, PMS-AM-6. DP 1 Cylinder, rephase, -/ x 1, PMS-AM-. DP 6 1 Cylinder, rephase, x 1, PMS-AM- DP 06 Cable tie, 11-/", standard DP 96 Cable tie, " DDP 16 1 Hose kit, LRII deluxe fold, shoemaker 99. DP 0 1 Hose, hydraulic, 1/ x 66 ( 6 ), 6FJX-6FJX 6. DP 06 1 Hose, hydraulic, / x 1 (11 ), FJX-FJX 7. DP 07 Hose, hydraulic, 1/ x 10 ( ), 6FJX-6FJX. DP 07 1 Hose, hydraulic, 1/ x 7 (6 6 ), 6FJX-6FJX 9. DP 07 1 Hose, hydraulic, / x 16 (1 6 ), FJX-FJX 0. DP 07 1 Hose, hydraulic, / x 7 (1 ), FJX-FJX 1. DP 09 Hose, hydraulic, 1/ x 6 ( ), MP-6FJX. DP Hose, hydraulic, / x (1 ), FJX-MP. DP Hose, hydraulic, / x ( ) JX-MP. DP Hose, hydraulic, 1/ x 90 (7 6 ), 6FJX-6FJX. DP 1 Flow divider combiner, shoemaker

56 Hydraulics 1 LRII -1/ Cylinders 10 Degree Fold Bundle Number

57 Bundle Number 791 Hydraulics 1 LRII -1/ Cylinders 10 Degree Fold Ref. Part No. Req. Description 1. AM 09 1 Mounting bracket divider combiner. AM 09 1 Transport cylinder lock. AM 1 Bracket, cylinder lug, -1/ cylinder, LR/LW 10 degree fold. AM 71 1 Transport lock, heavy duty, 1-/ x cylinder rod. BM 0 Clip pin, transport lock /16" x 1" 6. BP Nut, hex, /"-16, grade, plated 7. BP 00 Washer, lock, /, plated. BP 01 Washer, flat, /, plated 9. BP 0 Nut, hex, / -11, grade, plated. BP 09 Washer, lock, / plated 11. BP 0 1 U-bolt, / -16 x 6" x ", plated 1. BP Depth collar set, 1-/, heavy duty 1. BP 096 Hex cap screw, / -16 x -1/, grade, plated 1. BP 171 Hex cap screw, / -11 x, grade, plated 1. BP 1 1 Depth collar set,, extra heavy duty 16. BP 60 Tension bushing, 1-1/ x 1-1/ x DP 016 Adapter, MJ-MP, 90 degree male elbow 1. DP 11 Tee, side, 6MJ-6MJ-M, O-Ring 19. DP 01 6 Adapter, 6MJ-MSAE, 90 degree 0. DP 7 Cylinder, hydraulic, x 0, 000 psi, SAE DP 9 Adapter, MSAE-6MJIC DP 1 Cylinder, hydraulic -1/" x ", 000 psi, SAE w/adapters. DP 1 Cylinder, rephase, -1/ x 1, PMS-AM-6. DP 1 Cylinder, rephase, -/ x 1, PMS-AM-. DP 6 1 Cylinder, rephase, x 1, PMS-AM- 6. DP 7 1 Cylinder, rephase, -1/ x 1 PMS-AM-6 DP 06 Cable tie, 11-/", standard DP 96 Cable tie, " DDP 16 1 Hose kit, LRII deluxe fold, shoemaker DP 0 Hose, hydraulic, 1/ x 66 ( 6 ), 6FJX-6FJX. DP 06 1 Hose, hydraulic, / x 1 (11 ), FJX-FJX 9. DP 07 Hose, hydraulic, 1/ x 10 ( ), 6FJX-6FJX 0. DP 07 1 Hose, hydraulic, 1/ x 7 (6 6 ), 6FJX-6FJX 1. DP 07 1 Hose, hydraulic, / x 16 (1 6 ), FJX-FJX. DP 07 1 Hose, hydraulic, / x 7 (1 ), FJX-FJX. DP 09 Hose, hydraulic, 1/ x 6 ( ), MP-6FJX. DP Hose, hydraulic, / x (1 ), FJX-MP. DP Hose, hydraulic, / x ( ), FJX-MP 6. DP Hose, hydraulic, 1/ x 90 (7 6 ), 6FJX-6FJX 7. DP 1 Flow divider combiner, shoemaker. EM / ID x OD aluminum x 1-/16 hydraulic cylinder spacer 7

58 Hydraulic Selector Valve Wheel Lift Hoses Bundle Number 07 Wing Lift Hoses NOTE: Tape all pipe thread fittings only It is not necessary to tape the J.I.C. flare fittings. NOTE: Wire retainers are not included. Ref. Part No. Req. Description 1. AM 1 1 Bracket, universal. BP Nut, hex, / -16, grade, plated. BP 00 6 Washer, lock, /", plated. BP 0 U-bolt, / -16 x 6" x ", plated. BP 116 Hex cap screw, / -16 x ", grade, plated 6. DP 007 1/" male tip quick coupler FP 7. DP 016 Adapter MJ-MP 90 degree male elbow. DP 07 Quick coupler body, 1/" hydraulic 9. DP 09 Adapter MP-MP. DP 1 1 Selector valve 6 outlet, 1/" PT 11. DP 16 Hose, hydraulic, /" x 96"('-0"), MP-FJX

59 Shanks 1x Shank AP 06 Edge Bent Shank AP 1 9

60 Offset Stagger Brackets 1a 1a AAM 11 1 a AAM a a 9 a AAM 1 1 AAM 16 a 1 AAM a AAM 17 Ref. Part No. Req. Description 1. AAM 11 Bracket, offset, 1 x w/mounting hardware 1a. AM 9 1 Bracket, offset, 1 x, TMC Blue AAM 1 Bracket, offset, 16 x, w/mounting hardware a. AM 9 1 Bracket, offset, 16 x, TMC Blue. AAM 1 Bracket, offset, X, w/mounting hardware a. AM 9 1 Bracket, offset, x, TMC Blue. AAM 1 Bracket, offset, 16 x 1, w/mounting hardware a. AM 97 1 Bracket, offset, 16 x 1, TMC Blue. AAM 16 Bracket, offset, x 1, w/mounting hardware a. AM 9 1 Bracket, offset, x 1, TMC Blue 6. AAM 17 1 Bracket, offset, angled x 16, w/mounting hardware 6a. AM 9 1 Bracket, offset, angled, x 16 TMC Blue 7. BP 0 Nut, hex, / -, grade, plated. BP 0 Washer, lock, /, plated 9. BP 07 U-bolt, / - x x 7-/, plated 60

61 Row Clamp 61

62 Row Clamps 6

63 Row Clamps 6

64 Row Clamps 6

65 Row Clamps 6

66 Row Clamps 66

67 Super 100 Flex Coulter and Shank Parts a 1b a 1 AM 799 Coulter HD Super AM 7 Casting, coulter knee HD, machined with bushings 1a. AP 7 Bushing, 1-17/ OD x 1-/ ID x 1 OAL. 1 AM 796 Spring cap & guide heavy duty coulter. 1 AM 797 Coulter arm weldment HD. 1 AP 0 Bearing cone LM AP 0 Bearing cone LM AP 09 / x 1-1/ cotter pin 7. 1 AP 16 BLU-JET small decal 1-1/ x. AP 70 1/ -0 x 1 hex cap bolt 9. 1 AP 70 Hub cap 16.1 AP 70 / -16 spindle nut AP / x 1/16 x.1 spindle washer 1.1 AP 706-1Hub with cups, Bolt BC,.6 pilot 1a. 1 AP 07 Bearing Cup, LM 119 1b. 1 AP Bearing Cup, LM AP 77 Grease seal, 1TB 1.1 AP 1 *Spring.7 OD x.7 OAL,.6 wire DIA. 1.1 BP 07 1/ - grease zerk 16.1 BP 0-1/ OD x 1-/ ID x GA. machinery bushing And or as needed 16a. BP 06 Machinery Bushing, -1/ OD x 1-/ ID x 1 GA 17.1 BP0 Snap ring 1-/ External, BP 1/ - x / Hex cap bolt grade 0.1 AM 7 Coulter shank 16" 1.1 BP 16 /"x " roll pin.1 BP 0 Machine bushing -1/"x 1-/" ga..1 BP 19 /"x -1/" roll pin.1 BP 7/"x -1/" roll pin

68 Blades Coulter Blade Fluted Blade 0" AP 701 SealPro (Disc Sealer) Blade Options AM Notched Blade AM 7 1 hoe wheel AP 7 17 wavy 6

69 SealPro (AAM ) Disc Sealer 1 x Shank Parts 69

70 SealPro (AAM 6) Disc Sealer Edgebent Shank 70

71 SealPro II (AAM 7) Assembly, Optional Sealer II Spring Add-on Kit 1 Row AM Clevis, sealer spring, upper. AM 9 Clevis, sealer spring, lower. AM 90 Tube, upper spring, plated. AM 91 Bushing, spring collar, plated. AM 9 Tube, spring guide, plated 6. AP 997 Spring, 1.7 OD x 1.1 ID x 6.00 OAL 7. BP 0 Nut, hex, 1/ -1, grade, plated. BP 0 Washer, lock, 1/, plated 9. BP 00 Washer, flat, 1/, plated BP 16 Hex cap screw, 1/ -1 x 1-1/, grade, plated 11. BP 19 Hex cap screw, 1/ -1 x, grade, plated 1. BP Hex cap screw, 1/ -1 x -1/, grade, plated 1. BP Nut, hex lock, 1/ -1, plated 1. AP 116 Plug, Tube, 1-/16 71

72 SealPro II (AAM 7) Assembly, Optional Sealer II Spring Add-on Kit 1 Row 1 Mounting Spring Add-on Kit 1 17 NOTE: () (AM 9) sealer spring clevis must be mounted with the hole to the front 1. Mount () (AM 9) sealer spring clevis lower to arm with clevis hole to the front. Install () (BP 16) 1/ x 1-1/ grade hex cap screw. Secure with () (BP 0) 1/ lock washer and (7) (BP 0) 1/ hex nut.. Mount (1) (AM ) upper sealer spring clevis to sealer mounting bracket with () (BP 16) 1/ x 1-1/ grade hex cap screw. Secure with () (BP 0) 1/ lock washer and (7) (BP 0) 1/ hex nut.. Insert () (AM 9) spring guide tube into () (AM 91) spring collar bushing and align the holes. Place in lower clevis. Insert (11) (BP 19) 1/ x hex cap screw through clevis. Place (9) (BP 00) 1/ flat washers on both sides of bushing. Secure with (1) (BP ) 1/ lock hex nut.. Place (6) (AP 997) spring over () (AM 9) spring guide tube. 1 Hole to Front Place () (AM 90) upper spring tube over spring guide. Insert (1) (AP 116) tube plug in end of upper spring tube. 6. Lower spring assembly into upper clevis and insert (1) (BP ) 1/ x -1/ hex cap screw. Place (9) (BP 00) 1/ flat washers on both sides of upper tube. Secure with (1) (BP ) 1/ lock hex nut

73 SealPro II (AM 1) Assembly, Sealer Hanger With Blade Mounting 1. BP 79 1 Machinery bushing, 1-1/ OD x 1 ID x 1 GA. 7

74 Manual Holder c b d c c d a c d d. AAM 69 1 Manual Holder w/6 x a. AM Bracket, mounting, manual holder b. AP 1 Manual holder, Black, 01-1 c. BP 001 Nut, hex, / -16, grade, plated d. BP 00 Washer, lock, /, plated, c. BP Hex cap screw, / -16 x 1, grade, plated d. BP 0 1 U-bolt, / -16 x 6 x, plated 7 Geneeric Photo

75 Impellicone and Mounting Hardware 1 AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description 1. AM Bracket, Impellicone Mounting. BP 001 Nut, hex, /"-16, grade, plated. BP 00 Washer, lock, /", plated. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated. CP 6 1 Manifold, 1 port, Impellicone AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description 1. AM Bracket, Impellicone Mounting. BP 001 Nut, hex, /"-16, grade, plated. BP 00 Washer, lock, /", plated. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated. CP 6 1 Manifold, 1 port, Impellicone 7

76 SuperShooter III Parts AAM a b Cable tie 11-/ Standard 76

77 SuperShooter III Parts AAM 1 1 Super Shooter III Squibb Coupler/BodyGuard III 1. AM 76 1 Valve mounting, SuperShooter III. AM 76 Decal plate, 9 x 1, SuperShooter III. AM Coupler release plate, SuperShooter III. AM Coupler release handle, SuperShooter III. AP 7 1 Decal, Safety Instruction, NH, x 6. AP 1 1 Spring retainer washer 7. AP 97 1 Decal, BLU-JET SuperShooter III. AP 97 1 Decal, SuperShooter III Hookup instructions 9. AP 97 1 Decal, SuperShooter III, Squibb coupler operation\. BP 001 Nut, hex, / -16, grade, plated 11. BP 00 Washer, lock, /, plated 1. BP 01 Washer, flat, /, plated 1. BP 0 1 Compression spring SuperShooter 1. BP 07 1 Washer, flat, 7/16, plated 1. BP 1 1 Hex cap screw, 1/ -1 x, grade, plated 16. BP 1 Nut, hex lock, 1/ -1, plated 17. BP 701 Bolt, carriage, / -16 x 1, grade, plated 1. CCP 0 1 Quick coupler set, Squibb-Taylor FM1 a. CP 0 1 Quick coupler, Squibb, Female half, FM1-11 b. CP 06 1 Quick coupler, Squibb, Male half, FM CM 1 SuperShooter pedestal 0. CM 9 1 Body Guard, SuperShooter III 1. CP 01 1 Dust cap w/chain ACME adapter -6FC. CP 16 1 Snap ring, 1-1/ quick coupler. CP 1 ACME adapter 1-1/ MPT x 1-/ AM. CP 1 Nipple, hex, 1-1/ NPT, 000 PSI-cadmium plated. CP 66 1 Coupler, 1-1/ hex pipe steel, plated 6. CP 7 1 Valve, pressure relief, 0 psi, A-1 7. CP 1 Valve, bleeder, DP 01 1 Tee, MP-FP-FP 77

78 Meter Assembly 900 Single Standard Distribution Bundle Number: a AAM 6 b c d e 9 1 Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP Nut, Hex, / -16, grade, plated. BP 00 6 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 1 U-bolt, / -16 x 6 x, plated 6. CCP 61 1 Hose, EVA, / ft (CP 0 ft) 7. CCP 6 1 Hose, EVA, / ft (CP 0 ft). CM 1 1 NH gauge holder, tongue mount 9. CP 01 1 Meter Matic B900 w/hydraulic shutoff. CP 0 1 Gauge NH 0-60# 11. CP 0 0 Hose clamp wire / hose 1. CP 0 1 Hose barb 1/ x / hose A11 1. CP 1 Hose barb 1 Black pipe 1. CP 1 Hose clamp, worm gear, 1/ -1 tubing, SS 1. CP 1A 1 Hose, EVA, 1 reinforced x ( ) w/tie & tag 16. DP 006 Adapter, MP-FP, DP 01 1 Elbow, street, MP-FP 90 degree 1. DP 06 6 Cable tie 11-/ standard 19. DP 096 Hose, hydraulic, 1/ x 6 ( 0 ) 0. DP 96 1 Cable tie NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings

79 NH Pump Distribution 1R0 Bundle Number: a 1 b c AAM 6 d 7 11 e Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP Nut, Hex, / -16, grade, plated. BP 00 6 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 1 U-bolt, / -16 x 6 x, plated 6. CCP 61 1 Hose, EVA, / ft (CP 0 ft) 7. CCP 6 1 Hose, EVA, / ft (CP 0 ft). CM 1 1 NH gauge holder, tongue mount 9. CP 0 1 Gauge NH 0-60#. CP 0 0 Hose clamp wire / hose 11. CP 0 1 Hose barb 1/ x / hose A11 1. DP 01 1 Elbow, street, MP-FP 90 degree 1. DP 06 6 Cable tie 11-/ standard 1. DP 96 1 Cable tie NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings. 1 79

80 NH Pump Distribution 1R0 Bundle Number: a 1 b c AAM 6 d 7 1 e Generic Photo Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP Nut, Hex, / -16, grade, plated. BP 00 6 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 1 U-bolt, / -16 x 6 x, plated 6. CCP 61 1 Hose, EVA, / 1 ft (CP 0 1 ft) 7. CCP 6 1 Hose, EVA, / ft (CP 0 ft). CM 1 1 NH gauge holder, tongue mount 9. CP 0 1 Gauge NH 0-60#. CP 0 Hose clamp wire / hose 11. CP 0 17 Hose barb 1/ x / hose A11 1. DP 01 1 Elbow, street, MP-FP 90 degree 1. DP 06 0 Cable tie 11-/ standard 1. DP 96 1 Cable tie 1. CP Hose barb 1/ MP x / hose A CP 0 Plug, 1/ pipe, A NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings. 1 0

81 NH Pump Distribution 17R0 Bundle Number: 0000 a AAM 6 1 b c d 7 1 e Generic Photo Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP Nut, Hex, / -16, grade, plated. BP 00 6 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 1 U-bolt, / -16 x 6 x, plated 6. CCP 61 1 Hose, EVA, / 1 ft (CP 0 1 ft) 7. CCP Hose, EVA, / 7 ft (CP 0 7 ft). CM 1 1 NH gauge holder, tongue mount 9. CP 0 1 Gauge NH 0-60#. CP 0 6 Hose clamp wire / hose 11. CP Hose barb 1/ x / hose A11 1. DP 01 1 Elbow, street, MP-FP 90 degree 1. DP 06 Cable tie 11-/ standard 1. DP Cable tie 1. CP 00 1 Hose barb 1/ MP x / hose A NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings. 1 1

82 NH Pump Distribution 1R0 Bundle Number: a AAM b c d 6 11 e Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 (Qty. ) Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP 001 Nut, Hex, / -16, grade, plated. BP 00 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 U-bolt, / -16 x 6 x, plated 6. CCP 6 1 Hose, EVA, / 1 ft (CP 0 1 ft) 7. CCP 6 Hose, EVA, / ft (CP 0 ft). CM 1 NH gauge holder, tongue mount 9. CP 0 Gauge NH 0-60#. CP 0 Hose clamp wire / hose 11. CP 0 19 Hose barb 1/ x / hose A11 1. DP 01 Elbow, street, MP-FP 90 degree 1. DP 06 1 Cable tie 11-/ standard 1. DP 96 Cable tie 1. CP 0 11 Plug, 1/ pipe, square head 16. CP Hose barb 1 Black pipe 17. CP 1 Hose clamp, worm gear, 1/ -1 tubing, SS 1. CP Hose, EVA, 1 reinforced x 1 (1 ) w/tie & tag NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings. Generic Photo

83 NH Pump Distribution 17R0 Bundle Number: a AAM b c d 6 11 e Ref. Part No. Req. Description AAM 6 Impellacone 1 port W/Mount & Hardware, x 6 (Qty. ) Ref. Part No. Req. Description a. AM Bracket, Impellicone Mounting b. BP 001 Nut, hex, /"-16, grade, plated c. BP 00 Washer, lock, /", platedd d. BP 1 1 U-bolt, /"-16 x -1/16" x 7", plated e. CP 6 1 Manifold, 1 port, Impellicone 1 AAM 1 1 SuperShooter III/Squibb coupler/bodyguard III. BP 001 Nut, Hex, / -16, grade, plated. BP 00 Washer, lock, /, plated. BP 00 Hex cap screw, / -16 x 1-1/, grade, plated. BP 0 U-bolt, / -16 x 6 x, plated 6. CCP 6 17 Hose, EVA, / 1 ft (CP 0 1 ft) 7. CCP 6 Hose, EVA, / ft (CP 0 ft). CM 1 NH gauge holder, tongue mount 9. CP 0 Gauge NH 0-60#. CP 0 Hose clamp wire / hose 11. CP 0 1 Hose barb 1/ x / hose A11 1. DP 01 Elbow, street, MP-FP 90 degree 1. DP Cable tie 11-/ standard 1. DP 96 9 Cable tie 1. CP 0 9 Plug, 1/ pipe, square head 16. CP Hose barb 1 Black pipe 17. CP 1 Hose clamp, worm gear, 1/ -1 tubing, SS CP Hose, EVA, 1 reinforced x 1 (1 ) w/tie & tag NOTE: / EVA Hose Comes Partially Pre-cut to Length, Length Of Hose is Determined By Width Of Tool Bar. Number Of Pre-cut Sections Are Determined By Number Of Row Spacings. Generic Photo

84 AAM 171 Extension Bracket Two assemblies of AAM 171. Consult row spacing page for correct assembly if required Ref. Part No. Req. Description 1. AM 00 Bracket, Extension, 0 Double Mtg.. AM 01 1 Bracket, Extension, Angled End Mtg, 61. BP 0 16 Nut, Hex, / -, Grade, Plated. BP 0 16 Washer, Lock, /, Plated. BP 07 U-bolt, / - x W x 7-/ L, Plated 6. BP Hex Cap Screw, / - x -1/, Grade, Plated 7. BP U-bolt, / - x 6 W x -/ L, Plated

85 MaxPac AR700 Row Unit AAM 61 AR700 MaxPac Row Unit 1. AM 61 1 Backing plate, row unit AR 700 MaxPac row unit. AM 6 1 Assembly, AR700 MaxPac row unit. AP Decal, AR700 MaxPac, -1/ x 6. AP 1 1 Shank, 1-1/ x edge bent. BP 0 6 Nut, hex, / -, grade, plated 6. BP 0 6 Washer, lock, /, plated 7. BP 0 Nut, hex, 1/ -1, grade, plated. BP 0 Washer, lock, 1/, plated 9. BP 09 Hex cap screw, / - x, grade, plated. BP 1 Hex cap screw, 1/ -1 x -1/, grade, plated 11. BP 11 Hex cap screw, / - x grade, plated 1. BP Hex cap screw, 1/ -0 x 1, grade, plated

86 MaxPac AR700 6 Tube AAM 6 AR700 MaxPac Row Unit 1. AM 6 1 Backing plate, row mount w/coulter mount. AM 6 1 Assembly, AR700 MaxPac row unit. AP 1 1 Shank, 1-1/ x edge bent. AP Decal, AR700 MaxPac, -1/ x 6. BP 0 6 Nut, hex, / -, grade, plated 6. BP 0 6 Washer, lock, /, plated 7. BP 1 Hex cap screw, 1/ -1 x -1/, grade, plated. BP 0 Nut, hex, 1/ -1, grade, plated 9. BP 0 Washer, lock, 1/, plated. BP 09 Hex cap screw, / - x, grade, plated 11. BP 11 Hex cap screw, / - x grade, plated 1. BP 9 Bolt, carriage, 1/ -1 x -1/, grade, plated 1. BP Hex cap screw, 1/ -0 x 1, grade, plated 6

87 MaxPac AR AAM 6 Assembly, AR700 MaxPac 1. AP Spring,. OD x.7 ID x 9.06 OAL, BP 07 Nut, hex lock, / -, grade, plated. BP 07 Hex cap screw, / - x 7, grade, plated. EM Weldment, row mount, SCS 00. EM 66 1 Weldment, spring retainer, SCS EM / OD x ID DOM x -/, spacer bushing 7. EM 6 1 Weldment, shank holder, SCS BP Hex cap screw, 1/ -0 x 1, grade, plated 6 7

88 Basket Mount Arm & Coulter Extension 1 AAM 6 AR700 MaxPac Basket Mount 1. AM 71 1 Basket Mount, AR700 MaxPac, Extended. BP 0 Nut, hex, 1/ -1, grade, plated. BP 0 Washer, lock, 1/, plated. BP 16 Hex cap screw, 1/ -1 x 1-1/, grade, plated AAM 67 Coulter Bracket Extension Kit 9-7/ (Use when residue managers are mounted on coulters.) 1. AM 6 1 Bracket, coulter shank extension, (9-7/ ). BP 0 Nut, hex, 1/ -1, grade, plated. BP 0 Washer, lock, 1/, plated. BP 9 Bolt, carriage, 1/ -1 x -1/, grade, plated 1 1

89 MaxPac AR700 Assembly MaxPac AR700 row unit assembly 1. MaxPac AR700 row Unit a. AM 61 (1) backing plate, row unit AR 700 MaxPac row unit b. AM 6 (1) assembly, AR700 MaxPac row unit c. BP 0 (6) nut, hex, / -, grade, plated d. BP 0 (6) washer, lock, /, plated e. BP 09 () hex cap screw, / - x, grade, plated c d b e a. Insert (e) (BP 09) hex cap screws, / - x, into holes in (a) (AM 61) backing plate. Select backing plate holes to match toolbar tube size. Raise (b) (AM 6) Assembly, AR700 MaxPac row unit and insert / hex cap screws. Insert (e) (BP 09) hex cap screws, / - x, into bottom holes of (a) (AM 61) backing plate.. Place (d) (BP 0) / lock washers and (c) (BP 0) / hex nuts on each / hex cap screws.. Tighten all four hex cap screws. 9

90 MaxPac AR700 Assembly Installation of edgebent shank. Insert (AP 1) 1-1/ x edge bent shank. 6. Install two (BP 11) / x hex cap screws through row unit weldment and shank. Secure with (BP 0) / lock washers and (BP 0) / hex nuts. Installation of AAM 6 MaxPac Basket 7. Attach (AM 71) basket mount to MaxPac assembly with three (BP 16) 1/ hex cap screws from inside the MaxPac assembly through basket mount. Basket mount. Secure with (BP 0) 1/ lock washers and (BP 0) 1/ hex nuts. Location of torsion arm mounting For complete torsion arm assembly instructions consult Torsion Arm Manual

91 Torsion Arm Basket 91

92 Torsion Arm Assembly 9

93 Torsion Arm Basket Mounting Brackets Rigid Fertilizer Rows 9

94 Basket Mount Flat With Hardware 9

95 Torque Specifications 9

96 StripTill Residue Manager 96

97 AM 7670 Blade Mounting Assembly & Coulter Shank Extension Brackets 97

98 Residue Manager Assembly 9 96

99 Residue Manager Assembly 99 97

100 Residue Manager Assembly 0 9

101 Residue Manager Assembly 1 99

102 Residue Manager Assembly

103 Residue Manager Assembly

104 Hydraulic Repair Kits MFG # Bore/ TMC # Stroke Repair Kit Clevis Butt Gland SAE-0 " X " PMCK-SAE DP DP DP 11 DP 70 DP 6 SAE-00 " X 0" PMCK-SAE DP 7 DP DP 11 DP 70 DP 6 SAE- -1/" X " PMCK-SAE DP 1 DP 0 DP 11 DP 07 DP 0 PMS-AM-70-1/" X 1" PMCK-AM DP DP 6 DP 116 DP 6 DP 6 PMS-AM-6-1/" X 1" PMCK-AM DP DP 66 DP 116 DP 19 DP 1 PMS-AM- -/" X 1" PMCK-AM-A DP DP 67 DP 996 DP 97 DP 0 PMS-AM- " X 1" PMCK-AM-A DP 6 DP 6 DP 996 DP 70 DP 79 PMS-AM-6-1/" X 1" PMCK-AM DP 7 DP 69 DP 11 DP 19 DP 7 MFG # Bore/ Req Req Req TMC # Stroke Piston Piston Rod Barrel Tie Rod Clevis Pin Cotter Pin SAE-0 " X " DP DP DP 6 DP 7 DP BP 97 BP 11 AR-9-1/" X DP 9 DP 7 DP DP DP BP 97 BP 11 SAE-00 " X 0" DP 7 DP DP 7 DP DP BP 97 BP 11 SAE- -1/" X " DP 1 DP 09 DP 0 DP 0 DP 06 BP 9 BP 11 PMS-AM-70-1/" X 1" DP DP 6 DP 0 DP DP BP 0 BP 11 PMS-AM-6-1/" X 1" DP DP DP 0 DP 7 DP BP 0 BP 11 PMS-AM- -/" X 1" DP DP DP 99 DP 9 DP 9 BP 1 BP 11 PMS-AM- " X 1" DP 6 DP DP 99 DP 0 DP 9 BP 1 BP 11 PMS-AM-6-1/" X 1" DP 7 DP DP 1 DP 1 DP 0 BP 1 BP 11

105 Tie-rod Cylinder Disassembly - Assembly Procedure With cylinder removed from machine, clean, drained of oil and fully retracted, proceed as follows: Disassembly: 1. Secure cylinder in vice or other method to prevent rotation. With the immediate area clean of dirt so parts can be laid out.. Remove tie-rod nuts item (1). Pull rod assembly from cylinder. Remove tube item (). Loosen nut item () and remove clevis item () from rod assembly.. Place rod assembly in vice with copper or brass jaws so as not to damage. 6. Remove all seals from item (6), (), and (9) for replacement. Clean and inspect all parts, for damage (nicks, scratches, cracks and etc.) replace as necessary. If you have any question please contact Prince Engineering (71) -10. Reassembly: 1. Replace all seals in items (6), (), and (9). Do not replace small O-ring on ID of piston item () until ready to attach rod item ().. Place small ID O-ring seal for piston over rod turndown and apply light coat of grease to seal. Slip piston item () onto turndown with ID counter bore towards rod shoulder. Take care not to pinch O-ring between piston and rod shoulder. Replace nut item (7) and secure.. Apply light coat of grease to seals in gland item (6) and slip gland over rod end, carefully so as not to damage seals. Slip entire assembly into lightly oiled tube item () piston first. Insure tube slips up over OD seals of gland.. Take total assembly in step and slip tube over OD seal on butt item (9). Align ports in butt and gland and apply nuts item (1) to tie-rods and toque uniformly. Tierod / tierods 0- ft./lbs. (7-1 Nm) 1/ tierods - ft./lbs. (61-70 Nm) / tierods 9- ft./lbs. (19-1 Nm) / tierods -16 ft./lbs (0- Nm). Test for leaks and reinstall in machine. If you have any problems contact Prince Engineering (71)