Operator s/parts Manual

Transcription

1 1--1 4/8/04 Operator s/parts Manual 30 3-Section Flat Fold Marker Manufacturing, Inc. P.O. Box 5060 Salina, Kansas ! Read the Operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 1996 Printed 7/30/96

2 INTRODUCTION 4/8/ Your Great Plains 30 3-Section Drill Flat Fold Marker is designed to give you many years of dependable service. This manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions and service procedures carefully. The parts on your 30 3-Section Drill Flat Fold Marker have been specially designed and should only be replaced with genuine Great Plains parts. Therefore; should your drill require replacements parts, purchase them from your Great Plains Dealer. Space has been provided below for you to record your model number and serial number of your drill. Be sure to bring this information with you to your dealer when ordering parts or attachments for your drill. The following signal symbol and words should be clearly understood! When seen in this manual or on your equipment, this symbol and words will alert you to the seriousness of a situation. They should not be ignored or taken lightly.! The SAFETY ALERT SYMBOL indicates that there is a potential hazard to personal safety involved and extra safety precautions must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment; hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury This signal word is limited to the most extreme situations. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. SERIAL NUMBER MODEL NUMBER DATE PURCHASED

3 1-1 4/8/04 TABLE OF CONTENTS Introduction Table Of Contents Nut & Bolt Torquing Chart Safety Rules Flat Fold Marker Field Installation Diagram Installation Instructions Single Flat Fold Marker Hydraulic Assembly Instructions Dual Flat Fold Marker Hydraulic Assembly Instructions Maintenance and Lubrication Warranty Parts Drawings Table of Contents

4 NUT & BOLT TORQUING CHART 4/8/ This chart is based on torque requirements in foot pounds for grade 5 bolts. BOLT DIAMETER MINIMUM TORQUE MAXIMUM TORQUE BOLT DIAMETER MINIMUM TORQUE MAXIMUM TORQUE 1/4" /4" /16" /8" /8" " /16" /8" /2" /4" /16" /8" /8" /2" NOTE: Torque requirements listed above do not apply to self-locking nuts. For self-locking nuts increase torque requirements listed above by 15%.! SAFETY RULES! The safe operation of machinery is a big concern to farmers and manufacturers. Your Markers have been designed with many built-in safety features. However, no one should operate the Drill or Markers before carefully reading the Owner s Manuals. 1. NEVER permit anyone near machinery while in operation. 2. Excessive marker folding speed is dangerous and can cause marker damage. 3. NEVER allow anyone to be near the drill when cycling the markers. 4. Reduce speed of the tractor when transporting over uneven or rough terrain. Avoid all chuck holes and washboard areas in roads. 5. Reduce speed of the tractor when transporting over hills or steep slopes. 6. DO NOT lubricate, adjust or repair the drill or markers while in operation. 7. When in transport, use accessory lights and devices for adequate warning to operators of other vehicles and use safety hitch chain. Comply with all Federal, State and Local laws when traveling on public roads. 8. Use "Slow Moving Vehicle" emblem for warning vehicles approaching from the rear. 9. DO NOT permit smoking, sparks, or an open flame where combustible lubricants or liquids are being used. 10.! CAUTION! Escaping fluid under pressure can have sufficient force to penetrate the skin. Check all hydraulic lines and hoses BEFORE applying pressure. Fluid escaping from a very small hole can be almost invisible. Use paper or cardboard, NOT BODY PARTS, to check for suspected leaks. If injured, seek medical assistance from a doctor that is familiar with this type of injury. Foreign fluids in the tissue must be surgically removed within a few hours or gangrene will result. 11. DO NOT allow anyone to operate the Drill who has not been properly trained in its safe operation.

5 1-3 FLAT FOLD MARKER FIELD INSTALLATION DIAGRAM 4/8/

6 INSTALLATION INSTRUCTIONS FLAT FOLD MARKER 4/8/ FOR THE FOLLOWING ASSEMBLY INSTRUCTIONS, REFER TO THE ILLUSTRATION ON PAGE1-3. See the "Parts Section" of this manual to identify individual components not mentioned in these installation instructions. 1. Place drill in a lowered field position. From each end of the drill box allow 16 ft. clearance for marker assembly. 2. Attach the marker first section with mount (#1) to the marker mounting on the drill frame as illustrated. Mount the 5/8" x 2" long u-bolts (#32), lock washers (#9), and hex nuts (#10). 3. Assemble the marker in a horizontal position, remove the port plugs in the hydraulic cylinder to allow the fold cylinder to be extended. Then fold the first section and the lift lug (#1) to a horizontal position. 4. With the stop block positioned on top of second section (#2), align the holes of the second section with the holes of the first section (#1) and bolt together with the 5/8" x 5 1/2" long bolt (#5), lock nut (#4), 3/8" x 2" long shear bolt (#6), and lock nut (#7). 5. Place the third section (#3) over the end of the second section (#2) and insert hinge pin (#19) through the second and third section pivot. Secure the hinge pin (#19) with 1/4" x 2" long bolt (#17) and lock nut (#16). 6. Bolt the chain bar weldment (#13) to the first section (#1) with 3/8" x 3 1/4" long bolt (#11) and lock nut (#7). The chain bar weldment (#13) should pivot freely on the 3/8" bolt (#11). Bolt the chain bar (#18) to the third section (#3) with the 3/8" x 1 1/2" long bolt (#21) and lock nut (#7). The chain bar (#18) should pivot freely on the 3/8" bolt (#21). Connect the marker chain (#15) between the chain bar (#18) and chain bar weldment (#13) with 5/16" utility clevis (#14). With the marker disk adjusted for seeding width and disk touching the ground, adjust chain length to remove the slack. Adjustment should be made at the utility clevis (#14) nearest to the drill. 7. The purpose of the 3/8" x 2 1/2" long stop bolt (#12) is to hold tension on the marker chain (#15) ONLY when the marker is in folding position. Therefore; the 3/8" stop bolt (#12) and lock nuts (#7) should be positioned in the lift arm (#1) so the head of the stop bolt extends as little as possible. After marker is folded, adjust stop bolt to tighten chain. 8. When mounting the marker carrier arm (#27), on the 3-Section Drill, first mount the transport mount arm (#26) to the drill frame using 3/8" x 6" x 6 3/4" long u-bolt (#22), flat washers (#20), lockwasher (#23), and nuts (#24). The transport mount arm should be 50" - 60" away from the box end as shown. Next attach the marker carrier arm (#27) to the transport mounting arm (#26) using the 1/2" x 2" x 3" long u-bolts (#30), lockwashers (#28), and nuts (#29). The marker carrier arm should be set at 31 3/8" /8" above the drill frame as shown. 9. Mount the support arm saddle (#31) to the support arm (#27) with 1/2" x 2" x 3" long u-bolts (#30), lock washers (#28), and hex nuts (#39). The support saddle should be centered under the marker chain and the square tube of the second section (#2), when folded to prevent wear. The support arm should support the second section parallel with the seed box lid. Adjustment can be made by loosening the u-bolts that clamp the marker carrier and slide marker carrier (#30) up or down to parallel the marker with the drill box lid. 10. Fold the marker to transport position. With the marker chain (#15) in the slot of the support arm saddle (#31), take up the slack in the marker chain by threading 3/8" x 2 1/2" long stop bolt (#12) out against the chain bar weldment (#13), lock this stop bolt in position with the two lock nuts (#7).

7 1-5 SINGLE FLAT FOLD MARKER HYDRAULIC ASSEMBLY INSTRUCTIONS 4/8/ Fig. 1 Refer to Fig. 1 as reference for the following instructions: 1. Attach fittings (#1) & (#2) to cylinder ports. 2. Attach the needle valve (#3) and hoses to the cylinder fittings. 3. Bolt selector valve (#4) to the selector valve mount on T-Frame with 3/8" x 3" long bolts (#5), flat washers (#6) lock washer (#7) and nut (#8). 4. Route hydraulic hoses (#9) and (#10) from the fold hydraulic cylinders and marker hydraulic -cyl inders hoses (#11) and (#12) to the selector valve. 5. Route hydraulic hoses (#13) and (#14) from tractor, through the drill tongue to selector valve. 6. Secure with plastic tie (#15) straps to prevent kinking and pinching during folding operations. IMPORTANT! BEFORE FOLDING THE MARKER, BLEED ALL THE AIR OUT OF THE HYDRAU- LIC SYSTEM. 7. To bleed the air out of the hydraulic system, refer to page Adjust the speed of the marker with the needle valve to a low setting. Fold the marker up and down a few times and recheck for pinching and kinking of hoses. Reset folding speed with the needle valve to a safe speed.

8 DUAL FLAT FOLD MARKER ASSEMBLY INSTRUCTIONS 4/8/ Fig. 2 Refer to Fig. 2 as reference for the following instructions: 1. Attach the hydraulic fittings (#12) to the marker cylinder. 2. Install the selector/sequence valve to the selector valve mount, located on the T-Frame, using 3/ 8" bolts (#2), flat washers (#3), lock washers (#4), and hex nuts (#5). 3. Route hoses (#6) from the selector/sequence valve down the transport frame tube. Check hose routing for pinching and kinking of hoses and securely attach with plastic cable ties (#7). 4. Attach hoses to cylinder ports. Be certain to double check for correct port location back to the sequence valve. 5. Detach existing tractor hoses, (#8) and (#9), from fold cylinders. Attach 66" hose (#10), 42" hose (#11), and tractor hoses, (#8) and (#9), to the selector/sequence valve (#1) and fold cylinders. Assemble remaining hoses as indicated. 6. Cycle attached marker to transport position with the cylinder closed. Sequence valve should shift and activate the other cylinder. Refer to page 1-7 for proper cycle sequence. 7. When ready to fold wing boxes for transporting, position the handle on the selector/sequence valve towards the port marked "G". Hydraulic oil is now diverted to the fold cylinders.

9 1-7 BLEEDING OF THE HYDRAULICS 4/8/04 1. Be sure tractor hydraulic reservoir is full. 2. With the marker(s) in field position, crack the hydraulic hose fitting(s) located at the base end of the cylinder(s). With your tractor at an idle speed, activate your tractor hydraulic valve until hydraulic oil seeps out around the hose ends. Tighten the hose end fittings and repeat this process with the hose end fitting(s) located at the rod end of the cylinder(s). If dual markers are used with a selector/sequence valve, follow the procedure above for one marker cylinder. Then crack the fittings on the back side of the selector/sequence valve, activate the tractor hydraulics valve until hydraulic oil seeps out around the hose ends. Tighten the hose end fittings and repeat the complete process for opposite marker cylinder. 3. Fold and unfold the marker(s) slowly in order to work all the air out of your marker hydraulics. Use caution when folding and unfolding the marker for the first time, and check for pinching and kinking of hoses.! CAUTION! NEVER ALLOW ANYONE NEAR THE DRILL WHEN CYCLING THE MARKERS! 4. When the marker cylinder is equipped with a needle valve, screw the needle valve in to adjust the folding speed of the marker to a low setting. Fold the marker up and down a few times and recheck for pinching and kinking of hoses. With the tractor engine at an operating rpm, adjust the needle valve to limit the marker to a safe operating speed. When markers are equipped with a selector/sequence valve, the valve has an internal orifice that regulates the marker speed.! CAUTION! EXCESSIVE FOLDING SPEEDS CAN CAUSE MARKER DAMAGE!! CAUTION! ESCAPING FLUID UNDER PRESSURE CAN HAVE SUFFICIENT FORCE TO PENETRATE THE SKIN. CHECK ALL HYDRAULIC LINES AND HOSES BEFORE APPLYING PRESSURE. FLUID ESCAPING FROM A VERY SMALL HOLE CAN BE ALMOST INVISIBLE. USE PAPER OR CARDBOARD, NOT BODY PARTS, TO CHECK FOR SUSPECT- ED LEAKS. IF INJURED, SEEK MEDICAL ASSISTANCE FROM A DOCTOR THAT IS FAMIL- IAR WITH THIS TYPE OF INJURY. FOREIGN FLUIDS IN THE TISSUE MUST BE SURGICAL- LY REMOVED WITHIN A FEW HOURS OR GANGRENE WILL RESULT. MARKER HYDRAULICS, GENERAL NOTES... THE MARKERS CYCLE IN THE FOLLOWING SEQUENCE: (1) Right Up, Left Up (2) Right Down, Left Up (3) Right Up, Left Up (4) Right Up, Left Down (5) Sequence Repeats To fold the wing boxes for transporting, position the handle on the selector/sequence valve towards the port marked "G". Hydraulic oil is now diverted to the fold cylinders. NOTE: Raising and lowering speed of the dual markers is regulated by an internal orifice in the sequence valve which is sized for proper operation of the valve spool. DO NOT try to adjust or alter this orifice size. This will cause failure of the sequence valve. NOTE: JIC fittings do not require high torque. JIC and O-Ring fittings do not require sealant. Always use liquid pipe sealant when adding or replacing pipe thread fittings. To avoid possible danger of cracking hy hydraulic fittings from over tightening, DO NOT use plastic sealant tape.

10 MAINTENANCE AND LUBRICATION 4/8/ BREAKAWAY PROTECTION The marker arm (#2) is attached to the marker body (#1) with a 3/8" shear bolt. If excessive force is put on the marker during operation, the shear bolt will break, allowing the marker arm to swing away rather than cause damage to the marker. NOTE: The breakaway bolt is a 3/8"-16 x 2" long - grade 2 (G.P. # C). It is identified as a grade 2 by having no marks on the head. If it breaks, it must be replaced by an equivalent grade 2 bolt to prevent marker damage. LUBRICATION HINGES The marker body hinge pivots require greasing every hours of operation. Each marker has two grease fittings located at the center of each end of the first section. DISK BEARINGS The tapered roller bearings in the disk hub are lubricated at the factory. Under normal conditions, the bearings need to be repacked every 2 to 3 years. If the grease seal or grease cap becomes damaged or is missing, the hub should be disassembled, cleaned and bearings repacked. A new seal or grease cap should be installed. MARKER TRANSPORTING Always transport the marker with it folded in the flat fold position. Make sure the second marker section(s) rests securely on the transport carrier(s). 1. The marker blade comes factory assembled as shown in Fig. 3. The width of the mark that the blade makes can be adjusted by changing the angle of the blade. This is done by loosening the two 1/2" bolts in the blade adjuster, pivoting the blade to the preferred angle and MARKER BLADE ADJUSTMENTS tightening the bolts. 2. If desired, the angle of the blade can be reversed by turning the blade adjuster upside down and reversing the blade so the depth band is on the inside as shown in Fig Fig. 3 Fig. 4

11 1-9 TROUBLE SHOOTING 4/8/04 PROBLEM SOLUTION Hydraulic marker functioning improperly a. Check all hose fittings and connections for air and oil leaks. b. The chain on the folding marker should be slack when the marker is both fully extended and fully raised. c. Check tractor hydraulic oil level. d. Check all bolts and fasteners. e. If needle valve is plugged; open valve, cycle markers, and reset the needle valve. f. Double selector valve positioned for fold cylinders. Shift valve to marker sequence position. Blade does not mark a. The marker folding linkage and chain must have enough slack to allow the marker disk to drop down into depressions in the field. Maximum down float should be limited by the slots at the rod end of the marker cylinder, and not by the chain Read the adjustments section of this manual when adding slack to the chain. b. The blade may be reversed to pull dirt in or throw dirt out depending on soil conditions. See disk adjustments in this manual. c. An optional smooth blade is available through your Great Plains dealer. The notched blade comes with your marker as standard equipment.

12 4/8/ WARRANTY Great Plains Manufacturing, Incorporated warrants to the original purchaser that this seeding equipment will be free from defects in material and workmanship for a period of one year from the date of original purchase when used as intended and under normal service and conditions for personal use; 90 days for commercial or rental purposes. This Warranty is limited to the replacement of any defective part by Great Plains Manufacturing, Incorporated and the installation by the dealer of any such replacement part. Great Plains reserves the right to inspect any equipment or part which are claimed to have been defective in material or workmanship. This Warranty does not apply to any part or product which in Great Plains judgement shall have been misused or damaged by accident or lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or which has been used for a purpose for which the product is not designed. This Warranty shall not apply if the product is towed at a speed in excess of 20 miles per hour. Claims under this Warranty must be made to the dealer which originally sold the product and all warranty adjustments must by made through such dealer. Great Plains reserves the right to make changes in materials or design of the product at any time without notice. This Warranty shall not be interpreted to render Great Plains liable for damages of any kind, direct, consequential, or contingent, to property. Furthermore, Great Plains shall not be liable for damages resulting from any cause beyond its reasonable control. This Warranty does not extend to loss of crops, losses caused by harvest delays or any expense or loss for labor, supplies, rental machinery or for any other reason. No other warranty of any kind whatsoever, express or implied, is made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are herby disclaimed and excluded from this sale. This Warranty is not valid unless registered with Great Plains Manufacturing, Incorporated with 10 days from the date of original purchase.

13 1-11 NOTES 4/8/04

14 4/8/ /13/93 30' 3-SECTION DRILL FLAT FOLD MARKERS TABLE OF CONTENTS Flat Fold Marker Marker Disk Assembly Single Flat Fold Marker Hydraulic Assembly Dual Marker Hydraulic Assembly Cylinder { C} and { C} Double Selector Valve ( C) Selector Sequence Valve ( C) PARTS BOOK

15 1-13 FLAT FOLD MARKER 4/8/

16 FLAT FOLD MARKER (CON T) 4/8/ Ref. Part No. Description C NUT HEX 5/8-11 PLT C WASHER LOCK SPRING 5/8 PLT C HHCS 5/8-11X2 GR H RH MARKER MOUNT H H LH MARKER MOUNT RH FIRST SECTION H C LH FIRST SECTION BUSHING CYL 1 1/4 X 1 X C GREASE ZERK STRAIGHT 1/ D FIRST PIVOT SHAFT C HHCS 3/8-16X3 1/4 GR C NUT LOCK 3/8-16 PLT H LIFT LUG CHANNEL RH H LIFT LUG CHANNEL LH D SECOND PIVOT SHAFT C WASHER FLAT 1 SAE D MARKER CYLINDER PIN BODY C PIN COTTER 3/16 X C HHCS 1/2-13X4 3/4 GR C NUT LOCK 1/2-13 PLT C HHCS 3/8-16X2 GR D CYLINDER STOP D STOP BUSHING H RH 2ND SECTION H LH SECOND SECTION C WASHER FLAT 3/8 USS PLT C HHCS 3/8-16X1 1/2 GR D HINGE PIN H 30' F.F. MKR. 3RD. SECTION C NUT HEX JAM 1/2-13 PLT C SCREW SET SQ HD 1/2-13X1 1/2G C WASHER FLAT 1/2 USS PLT H 30' MARKER TUBE WELDMENT S MARKER DISC & HUB ASSEMBLY S REPLACED BY S C HHCS 1/2-13X3 GR C NUT HEX 3/8-16 PLT C CYL 3X20X1.25 ROD (TIE ROD) H CHAIN BAR WELDMENT C HHCS 3/8-16X2 1/2 GR5 FTHD C NUT HEX NYLOCK 5/8-11 PLT C HHCS 5/8-11X5 1/2 GR D MARKER CHAIN 30' C UTILITY CLEVIS 5/ D CHAIN BAR H MARKER CARRIER H MARKER TRANS ARM MOUNT WDMT C U-BOLT 3/8-16 X 6 1/32 X C WASHER LOCK SPRING 1/2 PLT C NUT HEX 1/2-13 PLT C U-BOLT 1/2-13 X 2 X 3 GR H SUPPORT ARM SADDLE C HHCS 1/4-20X2 GR C NUT LOCK 1/4-20 PLT C WASHER LOCK SPRING 3/8 PLT

17 1-15 MARKER DISK ASSEMBLY 4/8/

18 MARKER DISK ASSEMBLY (CON T) 4/8/ Ref. Part No. Description C HHCS 1/2-20X1 GR C GREASE CAP X C PIN COTTER 5/32 X 1 1/4 LG C NUT HEX SLOTTED 5/8-18 PLT C 14 4-BOLT MARKER DISK H DEPTH BAND 10 4-BOLT 4B.C C WASHER FLAT 5/8 SAE PLT C BEARING CONE #LM C BEARING CUP #LM C HUB MACH 4 4 BOLT 2.25 PILOT C SEAL 1 X X H 1 SPINDLE MARKER WELDMENT H MARKER DISK SPINDLE WELDMENT (Replaced by H) C HUB ASSY 44BOLT 2.25PLT3/4BRG (Includes items 2; 8; 10 and 11) S MARKER DISC & HUB ASSEMBLY S REPLACED BY S

19 1-17 SINGLE FLAT FOLD MARKER HYDRAULIC ASSEMBLY 4/8/

20 SINGLE FLAT FOLD MARKER HYDRAULIC ASSEMBLY (CON'T.) 4/8/ Ref. Part No. Description C Cylinder 3 1/2" x 24" x 1 1/2" Rod C Hydraulic Fitting 1/16" Orifice Plate C Hydraulic Fitting 3/4" O-RING x 9/16" JICM C Hydraulic Fitting 6 JIC M x 6 JIC F Tee C Hydraulic Fitting 3/8" M-F Elbow C Hydraulic Fitting -8 MORB x -6 JIC M Elbow C Hydraulic Hose 3/8" x 42 R C Hydraulic Hose 1/4" x 108 R C Hydraulic Hose 1/4" x 54 R C Hydraulic Hose 1/4" x 66 R C Double Selector Valve C Hydraulic Fitting 9/16" JIC x 1/2" MNPT 90? C Cable Tie C Hydraulic Hose, 1/4" x 21' Long C Hydraulic Hose, 1/4" x 272" Long C Hydraulic Fitting 1/2" MNPT x 3/8"Swivel 90? C Needle Valve 3/8" C Hydraulic Fitting 3/8" NPT Close Nipple C Hydraulic Cylinder 2 1/2" x 20" Stroke C Bolt, Hex Head 3/8"-16 x 3" Long C Washer, Lock Spring 3/8" C Washer, Flat 3/8" USS C Nut, Hex 3/8" C Hydraulic Hose 1/4" x 360 R C Hydraulic Hose 1/4" x 336 R1

21 1-19 DUAL FLAT FOLD MARKER HYDRAULICS ASSEMBLY 4/8/

22 DUAL FLAT FOLD MARKER HYDRAULICS ASSEMBLY (CON'T.) 4/8/ Ref. Part No. Description C Cylinder 3 1/2" x 24" x 1 1/2" Rod C Hydraulic Fitting 1/16" Orifice Plate C Hydraulic Fitting 3/4" O-RING x 9/16" JICM C Hydraulic Fitting 6 JIC M x 6 JIC F Tee C Hydraulic Fitting 3/8" M-F Elbow C Hydraulic Fitting -8 MORB x -6 JIC M Elbow C Hydraulic Hose 3/8" x 42 R C Hydraulic Hose 1/4" x 108 R C Hydraulic Hose 1/4" x 54 R C Hydraulic Hose 1/4" x 66 R C Selector/Sequence Valve C Hydraulic Fitting -8 JICF x -6 JICM Elbow (Pre July 1990) C Hydraulic Fitting -6 JICF x -6 JICM Swivel Elbow C Cable Tie C Hydraulic Hose, 1/4" x 21' Long C Hydraulic Hose, 1/4" x 272" Long C Hydraulic Fitting 3/8" FNPT Swivel x 9/16" MORB C Hydraulic Cylinder 2 1/2" x 20" Stroke C Hydraulic Hose 1/4" x 360 R C Hydraulic Hose 1/4" x 336 R C Bolt, Hex Head 3/8"-16 x 3" Long C Washer, Lock Spring 3/8" C Washer, Flat 3/8" USS C Nut, Hex 3/8"-16

23 1-21 CYLINDER 2 1/2" X 20" X 1 1/8" ROD { C} 4/8/

24 CYLINDER 2 1/2" X 20" X 1 1/8" ROD { C} (CON'T.) 4/8/ Ref. Part No. Description 1. 1M6006 Clevis 2. 2M3326 Rod 3. 3M3310 Head 4. 4M3102 Piston 5. 5M3128 Tube 6. 6M3128 Base 7. 7M3328 Tie Rod 8. 2A0208 Clevis Pin 9. 2A0208 Clevis Pin 10. * Wiper Seal 11. * O-Ring 12. * Back Up (Rod) 13. * O-ring 14. * Back Up (Piston) 15. 2A0022 Piston Nut 16. 2A0012 Clevis Nut 17. 2A0012 Tie Rod Nut 18. 2A0006 Cap Screw 19. 2A0132 Pin Clip C Seal Kit * Available in Seal Kit.

25 1-23 DOUBLE SELECTOR VALVE { C} 4/8/

26 DOUBLE SELECTOR VALVE { } (CON'T) 4/8/ Ref. Part No. Description 1. C Custom Valvepac Body 2. C Control Spool Assembly Snap Ring C Pin, Roll 1/4" O-Ring 7/8" OD x 3/32" C Nut, Lock 5/16" R19 Handle 8. CL-4422-PB Knob

27 1-25 SELECTOR SEQUENCE VALVE { C} 4/8/

28 SELECTOR SEQUENCE VALVE { C} (CON'T) 4/8/ Ref. Part No. Description Body, Aluminum Spool, Selector O-Ring, Buna N, 70 Duro Teflon, Back-Up Pin, Spring 5/16" x 4" Long Sleeve, Yellow Vinyl Snap Ring Truarc Pin, Spring 1/4" x 1 1/2" Long Spool Plug 10 SAE Ball, Steel 1/4" x 1 1/2" Ball, Steel 7/16" Diameter Spring Orifice & Guide Port Adaptor Elbow 1/4" NPT to #6 JIC Straight #6 SAE to #6 JIC Straight #8 SAE to #8 JIC Elbow #6 SAE to #6 JIC Spring, Compression O-Ring Plug