YANMAR (6ML-T) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION

Size: px

Start display at page:

Download "YANMAR (6ML-T) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION"

Lora Anthony
5 years ago
Views:

1 YANMAR (6ML-T) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION 防腐锌块 PROTECTIVE ZINC O 型圈 O-RING 缸套铜床 PACKING FOR CYL LINER COPPER 缸盖垫片 GASKET,CYLINDER HEAD 排气阀 EXHAUST VALVE 气阀锁块 PIECE 垫片 GASKET FOR AIR INLET TUBE 排气管垫片 GASKET,EXHAUST MANIFOLD 下弹簧座 SPRING SHOE,LOWER 出油阀接头 HOLDER 垫片 GASKET 进口接头组 STRAINER W/CASE 缸盖垫片 1.5 GASKET 1.5 CYLINDER HEAD O 型圈 O-RING 进气阀 INTAKE VALVE 排气导套 EXHAUST VALVE GUIDE 摇臂衬套 VALVE LEVER BUSH 摇臂罩垫 GASKET 进气导套 INTAKE VALVE GUIDE 外骨油封 OIL SEAL 阀杆垫块 PIECE FOR VALVE LEVER KNOB FOR BONNET KNOB FOR BONNET 垫片 GASKET 摇臂调节螺栓 ADJUSTING SCREW FOR VLAVE LEVER 出油阀 O 型圈 O-RING 32X 活塞销 PISTON PIN 衬套 BUSH 连杆螺栓 ROD BOLT U/S2.00 连杆瓦 U/S2.00 CRANK PIN BEARING U/S 柱塞 PLUNGER ASSY 定位柱塞套 STOPPER PLUNGER BARREL 垫片 GASKET 出油阀 DELIVERY VALVE WITH SEAT 高压泵等压阀 DEL VAVLE FOR HIGH PRESSURE PUMP 弹簧 SPRING 弹簧座 RETAINER,SPRING O 型圈 O-RING 油嘴垫片 GASKET FOR NOZZLE

2 O- 型圈 O-RING 空气启动阀垫片 GASKET FOR AIR STARTING VALVE 柱塞导承 GUIDE PLUNGER 主轴瓦 ( 后端 ) MAIN BEARING SHELL (REAR) 主轴瓦 MAIN BEARING SHELL 波纹管 FLEXIBLE JOINT 柱塞 17 PLUNGER 油嘴 DLF150 TB288 NOZZLE DLF150 TB 冷却油管 COOLING OIL PIPE(BONNET- NOZZLE) 冷却油管 COOLING OIL PIPE(NOZZLE- BONNET) 机械密封 MECHANICAL SEAL 柱塞 17 PLUNGER O 型圈 O RING 进气阀座 -DT VALVE SEAT SUCTION -DT 连杆瓦 CRANKPIN BEARING SHELL 螺栓 DEFLECTOR 排气阀座 SEAT,EXHAUST VALVE 油封 12X24X7 OIL SEAL 12X24X 油封 OIL SEAL SB 油封 OIL SEAL 油嘴 DL150T288 NOZZLE DL150T 螺栓 1/2X22 BOLT 1/2X 轴用弹簧挡圈 34 CIRCLIP, ROCKER ARM 铜垫片 PACKING 12X O- 型圈 P30 O-RING P O 型圈 O-RING O 型圈 G90 O-RING G 软轴 FLEX CABLE 示功阀总成 MAL INDICATOR ASSY 滑油泵总成 LUB OIL PUMP ASSY LUB OIL PUMP ASSY- TOROCHOID TYPE LUB OIL PUMP ASSY-TOROCHOID TYPE 起动阀总成 STARTING VALVE COMPLETE 高压油泵总成 FUEL INJECTION PUMP ASSY 燃料油喷射泵总成 FUEL INJECTION PUMP ASSEMBLY COMPLETE 油头总成 FUEL INJECTOR VALVE ASSY 活塞环 ( 缸付 ) PISTON RING(SET) 75 C 缸套 CYLINDER LINER

3 76 YANMAR MAL SUCTION 进气阀座 Φ86 Φ О SUCTION VALVE SEAT Φ86 Φ70 VALVE SEAT Φ86 Φ О О 垫片 ( 纸 ) PACKING,STOPPER(PAPER) 防腐锌块 PROTECTIVE ZINC 油封 12X22X7 OIL SEAL 12X22X O 型圈 O-RING 缸套铜床 PACKING FOR CYL LINER COPPER 缸盖垫片 GASKET,CYLINDER HEAD 缸盖侧盖垫片 PACKING CYLINDER HEAD SIDE COVER 螺钉 BOLT FOR KNOB 进气阀 SUCTION VALVE 排气阀 EXHAUST VALVE 气阀弹簧 ( 外 ) VALVE SPRING(OUTER) 气阀弹簧 ( 内 ) VALVE SPRING (INNER) 弹簧座 SPRING SUPPORT FOR VALVE 气阀锁块 PIECE 摇臂衬套 VALVE LEVER BUSH 燃油喷射阀螺栓 STUD FOR FUEL INJECTION VALVE 垫片 GASKET FOR AIR INLET TUBE 垫片 PACKING FOR IN TAKE MANIFOLD 排气管垫片 GASKET,EXHAUST MANIFOLD ADJUSTING LINER T-5 ADJUSTING LINER T 挺杆座 TAPPET SEAT 弹簧 SPRING RETAINER A PLUNGER RETAINER A PLUNGER SPRING SPRING 下弹簧座 SPRING SHOE,LOWER 卡簧 CIRCLIP GUIDE PLUNGER GUIDE PLUNGER 垫片 GASKET 出油阀接头 HOLDER H/P FUEL PUMP HOLDER DELIVERY VALVE H/P FUEL PUMP HOLDER DELIVERY VALVE 垫片 GASKET 燃油调节环 FUEL CONTROL RING 油枪弹簧 SPRING FOR NEEDLE VALVE 螺母 NUT FOR ADJUSTING BOLT 螺母 NUT FOR ADJUSTING BOLT 进口接头组 STRAINER W/CASE 过滤网 STRAINER (WITH CASE)

4 弹簧 SPRING 内转子 INNER ROTER 套 BEARING BUSH 叶轮螺母 NUT FOR IMPELLER 垫片 WASHER 轴承锁紧螺母 LOCK NUT FOR BEARING 锁紧螺母垫片 WASHER FOR LOCK NUT 密封固定器 HOLDER FOR PACKING 密封管 GLAND PACKING SEAL,COOLING WATER SEAL,COOLING WATER 垫片 PACKING FOR EXHAUST MANIFOLD NEEDLE VALVE SPRING NEEDLE VALVE SPRING 弹簧 SUCTION&EXHAUST VALVE SPRING 油嘴锁母 CASE NUT 主轴瓦 ( 后 ) MAIN BEARING(REAR) 活塞环 PISTON RING 活塞环 PISTON RING 柱塞总成 PLUNGER ASSY 主轴瓦 ( 后 ) THIN KELMET METAL 主轴瓦 MAIN BEARING METAL ASSLY 活塞销 PISTON PIN 排气阀 EXHAUST VALVE 叶轮 IMPELLER 缸盖垫片 1.5 GASKET 1.5 CYLINDER HEAD 垫片 GASKET 衬套 BUSH FOR CYL COVER 平行销 Parallel Pin 10x 主轴瓦 MAIN BEARING BUSH BUSH 内部衬套 BUSH INTERNAL EXTERNAL PIPE FOR COOLING WATER EXTERNAL PIPE FOR COOLING WATER O 型圈 O-RING 进气阀 INTAKE VALVE 排气阀 EXHAUST VALVE 排气导套 EXHAUST VALVE GUIDE 进气导管 INLET GUIDE 摇臂衬套 VALVE LEVER BUSH 螺母 NUT ADJUSTING SCREW 摇臂轴 VALVE LEVER SHAFT 摇臂轴 VALVE LEVER SHAFT 摇臂轴 VALVE LEVER SHAFT

5 摇臂架 ARM HOLD 销 PIN BONNET FOR LOWER BONNET FOR LOWER 摇臂罩垫 GASKET 垫片排气阀 PACKING EXHAUST VALVE LEVER WITH BUSH 进气阀杆 SUCTION VALVE LEVER WITH BUSH 进气导套 INTAKE VALVE GUIDE 外骨油封 OIL SEAL 阀杆垫块 PIECE FOR VALVE LEVER KNOB FOR BONNET KNOB FOR BONNET BLIND COVER BLIND COVER 垫片 GASKET 盖子 BLIND COVER FOR ZINC 摇臂调节螺栓 FOR ZINC ADJUSTING SCREW FOR VLAVE LEVER 摇臂罩螺栓 BOLT FOR BONNET 垫片 ( 方型 ) PACKING MANIFOLD SIDE 梃柱滚柱 TAPPET ROLLER 挺杆导套 TAPPET GUIDE 盖子 COVER FOR PUSH ROD 出油阀 O 型圈 O-RING 32X 弹簧 SPRING FOR PUSH ROD COVER 挺杆 PUSH ROD 挺杆帽 CAP PUSH ROD 推杆套筒 PUSH ROD HOUSING 紫铜垫 PACKING 阀导 VALVE GUIDE 垫片 GASKET 垫片 PACKING HOLDER 手轮 HANDLE 螺母 LOCK NUT 波纹管 FLEXIBLE JOINT(1-3 CYL) 波纹管 FLEXIBLE JOINT(4-6 CYL) 活塞销 PISTON PIN 活塞销 PISTON PIN 板 PLATE FOR DO BOLT DOE DO BOLT DOE DO PISTON PIN METAL PISTON PIN METAL 衬套 BUSH 连杆螺栓 CONNECTING ROD BOLT

6 连杆螺栓 ROD BOLT 连杆螺栓 ROD BOLT 连杆瓦 CRANK PIN BEARING 连杆瓦 CRANK PIN BEARING U/S2.00 连杆瓦 U/S2.00 CRANK PIN BEARING U/S 内外转子总成 INNER & OUTER ROTOR ASSY 轴承衬套 BEARING BUSH (MIDDLE) 轴承衬套 BEARING BUSH (B) 弹簧 SPRING 垫片 PACKING 齿轮 GEAR 油封 OIL SEAL COVER LUB OIL OUTLET COVER LUB OIL OUTLET COVER LUB.OIL COOLER COVER LUB.OIL COOLER 填料 Packing 垫片调节阀 SPRING 弹簧 PACKING ADJUSTING VALV.ASSY OIL PRESSUREL 滤芯 FILTER LUB OIL 滑油滤芯 FILTER 150MESH 垫片 PACKING(4) HOLE 自清滤器 AUTO CLEAN L= 垫片管接头油管 PACKING, RUBBER 30/55x12.5 PIPE JOINT ROCKER ARM SHAFT OIL SUPPLY LUB OIL PIPE(CYLINDER HEAD VALVE LEVER SHAFT) 垫片 PACKING FOR CASING 衬套 BUSH 叶轮 182 IMPELLER 182 MAL 叶轮轴 SHAFT FOR IMPELLER 泵轴 356 IMPELLER SHAFT 定距块 DISTANCE PIECE D-34E 柱塞 PLUNGER WITH BARREL 弹簧 SPRING CASE 定位螺钉 STOPPER, PLUNGER BARREL 垫片 PACKING 垫片 GASKET 出油阀 DELIVERY VALVE 出油阀 DELIVERY VALVE 出油阀高压泵等压阀 DELIVERY VALVE WITH SEAT DEL VAVLE FOR HIGH PRESSURE PUMP

7 弹簧 SPRING DELIVERY VALVE 弹簧 SPRING 出油阀接头 HOLDER,DELIVERY VALVE 出油阀接头 HOLDER,DELIVERY VALVE 垫圈 WASHER(HOLDER) 弹簧座 RETAINER SPRING 垫片 GASKET O 型圈 O-RING 调节齿条 PINON FUEL CONTROL 轴 SHAFT CONTROL RACK 气孔堵 PLUG, AIR VENT 防护塞 PLUG,PROTECTIVE 销子 PLUG PROTECTIVE 油嘴 DL150T258 NOZZLE DL150T 高压油泵进油管 F.O.INJECTION PIPE 油嘴垫片 GASKET FOR NOZZLE 推杆 INTER SPINDLE 调压弹簧 SPRING FOR NEEDLE VALVE 调节螺栓 ADJUSTING BOLT FOR SPRING 螺套 SPRING CASE 盖 CAP FOR SPRING CASE 油嘴垫片 GASKET FOR NOZZLE 承碟 RETAINER 调节螺钉 ADJUSTING BOLT SPRING 螺母 BODY FOR NEEDLE CASE NUT BODY FOR NEEDLE HOLDER HOLDER 垫片 PACKING FOR DO 调节螺栓 ADJUSTING SCREW 挺杆 ADJUSTING CREW TAPPET 燃油滤芯 FO ELEMENT FILTER 金属丝滤芯 NOTCH-WIRE ELEMENT 高压油泵进油管 F.O.INJECTION PIPE 主管 MAIN PIPE PUMP UMOUN NEW UMOUN NEW 锣帽 CAP NUT 高压油管燃油喷射阀垫片高压油管 PACKING FOR FUEL INJECTION VALVE 垫片 Packing for Governor Case 垫片 Packing for Bearing Mounting PACKING PACKING 齿轮 Governor Gear D=104,37 Z= 轴承 BEARING 30209

8 环 Ring for Lub.oil 调速器推力轴承 (51108) BEARING 调速器推力块座 PUSH PIECE SEAT 调速器升降套筒 BUSH 升降套筒下铜套螺母 BUSH NUT FOR SCREWING SCREW ADJUSTING 垫片 WASHER FOR ROLLER RD LEVER 3RD LEVER 调节板 Adjusting Plate 调节垫片 Adjusting Packing 螺母 Nut for Weight Pin M 衬套 BUSHING FOR PINION 定距块 DISTANCE PIECE (B) 定距块 DISTANCE PIECE (B) PLANET GEAR SHAFT BALL 1/4 FOR BALL PLANET GEAR SHAFT BALL 1/4 FOR BALL BEARING BEARING 调节螺钉 ADJUSTING SCREW 导管 GUIDE FOR SPRING 调节螺母 ADJUSTING NUT 销 PIN FOR SPRING GUIDE 联接杆 COUPLING ROD 启动阀 STARTING VALVE 启动阀弹簧 STARTING VALVE SPRING L 启动阀垫片 GASKET FOR STARTING VALVE O- 型圈空气启动阀垫片温度计 500C 排气管总成 (4-6 缸 ) O-RING GASKET FOR AIR STARTING VALVE THERMOMETER500C EXHAUST MANIFOLD COMPLETE (CYLINDERS NO4-6) 垫片 PACKING 排气管垫片排气管弹性接头 PACKING,FLEXIBLE JOINT EXHAUST PIPE BELOWSE FLEXIBLE JOINT 活塞 PISTON (FC) 叶轮 184 IMPELLER 球窝接头 BALL JOINT N/A 燃油喷射泵体燃油喷射阀体 BODY, FUEL INJECTION PUMP BODY,FUEL INJECTION PUMP FUEL INJECTION VALVE 柱塞总成 Plunger & Barrel ( teta 17mm ) 柱塞导承 GUIDE PLUNGER

9 长型油嘴针阀偶件 ( 长 )0.28X8X150 NEEDLE V/V AND CASE NEEDLE VALVE(LONG NEEDLE)0.28X8X 温度计 THERMOMETER 500CX1/2X 主轴瓦 ( 后 ) MAIN BEARING (REAR) 主轴瓦 ( 后端 ) MAIN BEARING SHELL (REAR) 主轴瓦 MAIN BEARING SHELL 主轴瓦 MAIN BEARING SHELL 主轴瓦 MAIN BEARING SHELL 垫片 PACKING FOR AIR COOLER 橡胶管 RUBBER HOSE,D-124,H 波纹管 FLEXIBLE JOINT 连杆瓦端盖 ROD METAL(BOTTOM BEARING) SIDE COVER COOLING WATER INLET 接头 N/A JOINT N/A 螺栓 N/A N/A 冷却水管 COOLING WATER PIPE N/A 柱塞 17 PLUNGER 柱塞总成 PLUNGER AND BARREL RACK FUEL CONTROL RACK FUEL CONTROL RACK, FUEL CONTROL RACK, FUEL CONTROL 垫片 PACKING C.O.PUMP FITTING t= 燃油组合泵油头冷却泵布司 BUSH 油头冷却泵内齿轮 GEAR 油封 30X42X8 OIL SEAL 30X42X 双头螺栓 1/2x130 STUD 1/2X 软轴 SHAFT TACHOMETER 油嘴 DLF150 TB288 NOZZLE DLF150 TB 油嘴 DLF150 TB288 NOZZLE DLF150 TB 喷油器体 BODY,INJECTOR 推杆 INTER SPINDLE 挡板 OIL STOPPER PLATE 高压油管 F.O.INJECTION PIPE 冷却油管 COOLING OIL PIPE(JOINT-BINNET) 油头冷却油管 FUEL OIL PUPE 燃油管 FUEL OIL PIPE 油头冷却油管 FUEL OIL PUPE 燃油管 FUEL OIL PIPE 弹簧 SPRING D48 P.C. L 缸套 CYL LINER 活塞 PISTON AL E-8 活塞 PISTON O 型圈 O RING

10 波纹管 FLEXIBLE 冷却油管 JOINT,TURBOCHARGER COOLING OIL PIPE(BONNET 冷却油管 NOZZLE) COOLING OIL PIPE(NOZZLE INNER AND OUTER BONNET) INNER AND OUTER ROTER ASSY ROTER ASSY O 型圈 O RING 止动垫片 35 LOCK WASHER 挡水圈 COLLAR WATER SHIELD 油封 OIL SEAL TC 活塞 PLUNGER AND BARREL 弹簧 SPRING D31 P.C. L 柱塞 17 PLUNGER 出油阀 DELIVERY VALVE 高压油水泵 PACKING OR CONTROL 柱塞 PLUNGER W/BARREL 柱塞 STOPPER PLUNGER PLUNGER WITH BARREL STOPPER PLUNGER BARREL BARREL 进气阀 INTAKE VALVE 油管 PIPE 排气阀 EXHAUST VALVE 排气阀 EXHAUST VALVE 气阀导管 VALVE GUIDE 阀帽密封 PACKING BONNET 摇臂衬套 ROCKER ARM BUSH 阀帽密封 PACKING BONNET 阀帽密封垫片 PACKING BONNET GASKET FOR EXHAUST MANIFOLD O 型圈 O RING INTER SPINDLE INTER SPINDLE 连杆瓦 CRANKPIN BEARING SHELL 柱塞总成 17 PLUNGER ASSY 金属杆 ROD METAL OVER/ZE 0.4mm 燃油组合泵布司 BUSH 锥形柱塞 Taper Plug DRIVING MOUNTING DRIVING MOUNTING 排气阀座 SEAT,EXHAUST VALVE 温度计 THERMOMETER 油封 OIL SEAL 油封 12X24X7 OIL SEAL 12X24X7

11 套 D32Xd25 L39.5 BUSH D32Xd25 L 温度计 THERMOMETER 500CX1/2X 温度计 THERMOMETER 插杆上油封 ( 胶套 ) OIL SHIELD CAP 活塞环 PISTON RING 活塞环 PISTON RING 活塞环 PISTON RING 活塞环 PISTON RING 活塞环 PISTON RING RING SET RING SET 油封 OIL SEAL SB 油封染油阀油嘴总成 OIL SEAL FUEL VALVE NOZZLES ASSY 染油阀油嘴总成 0.28X28X159 FUEL VALVE NOZZLES ASSY 0.28X28X 示功阀手柄 HANDLE 垫片 PACKING STOPPER, CONTROL RACK STOPPER, CONTROL RACK 空气堵 PLUG,AIR PLUG 螺栓 1/2X35 BOLT 1/2X BOLT 3/8X35 BOLT 3/8X 螺栓 1/2X22 BOLT 1/2X 螺栓 W1/2X35 BOLT W1/2X 螺栓 STUD 3/8 X 螺栓 STUD 3/8 X 双头螺栓 3/8X32 STUD 3/8X 双头螺栓 1/2X32 STUD 1/2X 螺母 Nut 7/8 inch 垫圈 Washer 轴用弹簧挡圈 34 CIRCLIP, ROCKER ARM 弹性挡圈 Circlip 销 3X36 TAPER PIN 3X 销 3X36 TAPER PIN 3X 销 5X28 TAPPER PIN 5X 销 5X32 TAPER PIN 5X 锥销 6X32 TAPER PIN 6X 开口销 SPLIT PIN 4X 开口肖 SPLIT PIN 55X 键 5X14 KEY 5X GUIDE PLUNGER GUIDE PLUNGER 接头 JOINT 连接 UNION 螺帽 CAP NUT 6

12 管接头螺栓 PIPE JOINT BOLT 管接头螺栓 BOLT 15 PIPE JOINT(150) 铜垫片 PACKING 12X 垫片 14 GASKET 垫片 PACKING 垫片 COPPER PACKING FOR CAP NUT 垫片 HOUSING PACKING 垫片 25 GASKET 垫片 PACKING 销子 JOINT BOLT FUEL PUMP PLUG 12 JOINT BOLT FUEL PUMP M20 M 铰接螺栓 PIPE JOINT BOLT 轴承 6205 BEARING O 型圈 O-RING O- 型圈 P30 O-RING P O 型圈 O-RING O 型圈 O RING O 型圈 O-RING G O 型圈 G90 O-RING G 螺钉 Bolt M10x 双头螺栓 M12X45 STUD M12X 锁母 LOCK NUT 顶丝 M4X0.7X5 SET SCREW M4X0.7X X6 定位螺钉 4X6 SET SCREW 4X 螺丝 Set screw 6x 油嘴清洁工具 NOZZLE CLEANING TOOL 压力计 PRESSURE GAUGE 压力计 PRESSURE GAUGE FUEL OIL 压力表 DU1/4X60X6 PRESS.GAUGE DU1/4X60X 压力表 PRESSURE GAUGE COOLING 压力表 WATER DV 75*6 PRESSURE GAUGE LUB OIL DV 75* 温度计 100C L158 PF3/8 THERMOMETER 100C L158 PF3/ 温度计 L.O.THERMOMETER 转速表 100X950 TACHOMETER 100X 转速计 TACHOMETER 转速计 TACKOMETER 300- TACHOMETER TACKOMETER RPM(FKS) 1500RPM(FKS) 软轴 FLEX CABLE 轴承螺栓 BEARING BOLT(WITH NUT) 高压油管 INJECTOR HIGH PRESSURE PIPE

13 凸轮轴 CAM SHAFT 膨胀接头 430X380 EXPANSION JOINT 430X 翼式泵翼式泵 WING PUMP WING PUMP 转速表 ( 额定转速 : TACHOMETER(100*900) MAL-24x18x RPM) 紫铜垫 24X18X2 高压油泵导套及滚轮组 PACKING 24X18X2 TAPPET ASSEMBLY FOR F.O.PUMP INDICATOR COCK & SAFETY VALVE 活塞 PISTON BONNET BONNET 缸头缸盖 CYLINDER HEAD CYLINDER HEAD(BAR) 挺杆 TAPPET ASSY(INCLUDING 26 TO 29) 示功阀总成 MAL INDICATOR ASSY 示功阀总成 MAL INDICATOR ASSY 示功阀旋塞 INDICATOR COCK 示功旋塞总成 INDICATOR COCK ASSY 活塞环 ( 缸付 ) PISTON RING(SET) 滑油泵总成滑油泵总成 LUB OIL PUMP ASSY LUBR.OIL PUMP COMPLETE(used) 滑油泵总成 LUB OIL PUMP ASSY-TOROCHOID TYPE 燃油喷射泵 FUEL INJECTION PUMP 油泵总成 FUEL INJECTION PUMP ASSY 燃油给油泵总成 FUEL OIL FEED PUMP ASSY 喷油器总成 FUEL INJECTOR ASSY 梃杆 TAPPET ASSY FOR F O PUMP 起动阀总成活塞冷却水泵总成 ( 泵壳为铁 ) STARTING VALVE COMPLETE PISTON -FC TYPE COOLING WATER PUMP COMPLETE(THE MATERIAL OF PUMP BODY IS IRON) 高压油泵总成 FUEL INJECTION PUMP ASSY 燃油喷油泵总成 FUEL INJECTION PUMP ASS'Y 燃料油喷射泵总成 FUEL INJECTION PUMP ASSEMBLY COMPLETE 油头总成 FUEL INJECTOR VALVE ASSY 高压油管 ( 双层 ) FUEL INJECTION PIPE 活塞 MAL-UT AL PISTON MAL-UT AL GOBERNOR ASSY GOBERNOR ASSY 冷却水管 COOLING WATER PIPE

14 冷却水调节阀 COOLING WATER REGULATING VALVE ASSY 推力杆 PUSH ROD 顶杆 PUSH ROD 缸套 LINER 活塞环 ( 缸付 ) PISTON RING(SET) 518 BUSH L 衬套 BUSH L 519 C 示功阀旋塞总成 INDICATOR COCK ASSY 520 C 油头总成 ( 不带油嘴 ) Fuel injection valve assy. 521 C 高压油管 High pressure tube assy. for F.O 522 C CYL HEAD CODE CYL HEAD CODE 523 C 连杆 MAL CONNECTING ROD MAL 524 C 活塞 MAL-UT AL PISTON MAL-UT AL C C 缸套缸套 CYLINDER LINER WITH PACKING CYLINDER LINER 527 C 缸套 CYLINDER LINER WITH RUBBER PACKING 528 C 活塞 AL ONLY BARE PISTON AL ONLY BARE C C 活塞活塞 PISTON WITHOUT RING PISTON 531 MAL-LINER O RING LINER O-RING (SET LINER O-RING (SET COMPLETE) 532 MAL-PISTON RING SET COMPLETE) 活塞环 PISTON RING SET 533 MAL-THERMOMETER 温度计 THERMOMETER CELCIUS 534 MAL-THERMOMETER 0- 温度计 THERMOMETER CELCIUS MAL-UPPER BUSH 连杆衬套 CONNECTING ROD UPPER BUSH 536 P p PRESSURE GAUGE 3KG/CM3 539 PRESSURE GAUGE 4KG/CM2 540 THERMOMETER,EXHAU ST (3/8) 541 YANMAR MAL SUCTION VALVE SEAT Φ86 Φ О 橡胶垫圈橡胶密封压力表压力表 RUBBER PACKING PACKING(RUBBER) PRESSURE GAUGE 0-3KG/CM2 PRESSURE GAUGE 0-4KG/CM2 温度计 THERMOMETER,EXHAUST (3/8) 进气阀座 Φ86 Φ О SUCTION VALVE SEAT Φ86 Φ О CATALOGUE

SULZER (RLB76) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION

SULZER (RLB76) ITEM PART NO. 中文名称 ENGLISH DESCRIPTION 1 4RLB76-R -23119 刮油环 OIL SCRAPER RING IN THREE PARTS,COMPLETE 2 4RLB76-R -23120 刮油环 OIL SCRAPER RING IN THREE PARTS, COMPLETE 3 4RLB76-R -27127 圆橡胶圈