SINGLE DISC PLANTER - OPERATOR S MANUAL -

Size: px

Start display at page:

Download "SINGLE DISC PLANTER - OPERATOR S MANUAL -"

Elwin Watkins
5 years ago
Views:

1 SINGLE DISC PLANTER - OPERATOR S MANUAL - MISIONES 830 (X2659 BIL) - MONTE MAÍZ - CÓRDOBA - ARGENTINA PHONE: 54-(03468) 47-34/35 - FAX: 54-(03468) SALES DIVISION FAX: 54-(03468) ingersoll@ingersollarg.com.ar

2 INGERSOLL ARGENTINA S.A. Thanks you for trusting our products. Kindly read this manual for proper operation. OPERATOR S MANUAL

3 INDEX WARRANTY CONDITIONS...3 SAFETY...4 MAINTENANCE...5 SPECIFICACIONES...6 SINGLE DISC SEEDING UNIT...7 SEEDING SHOE...8 MAIN HOLDER...2 DISC HOLDER HUB...3 PRESS WHEEL...4 COVER WHEEL...6 LEVELLING WHEEL...20 COMPRESSION SYSTEM...22 FIELD ADJUSTMENT...23 INGERSOLL ARGENTINA S.A. Reserves the right to discontinue parts at any time, or change specifications, design or prices without notice and without obligations. MADE BY

4 WARRANTY CONDITIONS.. Warranty Statement: INGERSOLL ARGENTINA S.A. Warrants its products are free from defects in materials and workmanship under normal wear and tear conditions on proper installation, application, handling and use for a period of 2 months from date of sale by INGERSOLL ARGENTINA S.A. 2. Warranty is limited to replacement of defective product only. NOTE: It does not cover the cost of freight, removal and replacement of product and forwarding or returning of product. 3. The buyer must notify INGERSOLL ARGENTINA S.A. Immediately of any faulty product or workmanship. 4. Replacements parts will be issued to the customer and charged to their account until the customer returns the faulty parts. These parts whill then be thoroughly investigated and if a warranty claim is approved a subsequent credit will appear on the customers account. Limitations - The warranty shall not apply to the following:. Alterations and repairs not approved by INGERSOLL ARGENTINA S.A. 2. Any product or part, which has been subjeted to misuse, negligence, improper installation or accident. 3. Any routine maintenance items. 4. Normal deterioration of paint, trim and appearance items due to wear and exposure. 5. Normal noise and vibration. 6. Damages, consequential and indirect loss or expenses, failure or corrosion resulting from:. Accident, theft, fire or misuse.. Failure by the buyer or its representatives to perform prope maintenance services.. Use of parts not supplied by INGERSOLL ARGENTINA S.A.. Environmetal conditions, act of god and other events beyond the control of INGERSOLL ARGENTINA S.A. 3

5 SAFETY. Safety relies heavily upon the actions of the machine operator. The operator of the machine must be trained accordingly in the safe operation of this implement. The operator must be familiar safety requirements and be continually safety conscious. Although INGERSOLL ARGENTINA S.A. has constructed this machine with a high degree of safety in mind, an experienced, careful and safety conscious operator is vital for the machine safe operation. 4

6 MAINTENANCE. General: During and after the first day of operation and periodically thereafter, check the tightness of all U-bolts, Shell Clamps, Bolts and Nuts. Wheels: Check the tightness of wheel nuts after the firts hour of operation and again after ten hours. Thereafter, check bolts/nuts periodically and keep them tight. Refer to Specifications for correct torque. Wheel Bearings: Once every year or every 250 hours of operation, whichever comes first, service and replace if necessary, all wheel bearings on the implement. Caution: Do not wash bearings in kerosene, as this will leave a film, which prevents grase adhering to the rollers, resulting in overheating, and damage to the bearings. Consumable Components. Inspect consumable wear components daily. Replace all worn out genuine Ingersoll Argentina S.A. consumables with Using consumable parts beyond their wear limitations can cause damage to more expensive components. Lubrication: If applicable all chains should be lubricated daily using a spray on chain lube. Using recommended grease (refer to Specifications ). Lubricate the implement in the locations shown in the spare parts pages. DO NOT ATTEMPT LUBRICATION OF IMPLEMENT OR MAKE ADJUSTMENTS WHILE TRACTOR ENGINE IS RUNNING. ALWAYS USE THE SAFTY STANDS PROVIDED. 5

7 SPECIFICATIONS. Lubrication: Grease - lithium based multipurpose grease. Bolt Torque. NOTE: Tighten all U-bolts to 80 % of above torque for equivalent diameter bolts. 6

8 SINGLE DISC SEEDING UNIT. Ingersoll s Single Disc Seeding Unit has been manufactured to face heavy duty seeding and fertilizing tasks. The 8 plain disc at a 7 angle opens a furrow leaving the soil firmly pressed on one side but stirred on the other. A 4 ½ x 5 levelling wheel determines furrow depth while a cast shoe working jointly with the blade places seed and fertilizer in the furrow through independent down comers. A press wheel guarantees accurate seed placement at the bottom of the furrow for improved emergence. A cover wheel system covers the furrow. The Single Disc Seeding Unit is ideal for minimizing trash removal and soil stirring. Highly recommended for clayish, sticky soils and also for salty soils where non-stirring is appreciated. 7

9 - SEEDING SHOE. The cast seeding shoe is hardfaced on the area where wear is the greatest and features two downright, independent anti-blockage tubes for fertilizer and seed. The seed tube includes another smaller tube for fodder seeding. SEEDING SHOE ADJUSTMENT Check tube position. Trim the bracket after tightening it round the plastic tube. Make sure the bracket is not an obstacle for mobile parts such as the main holder Do not apply hardfacing to the machined surface as it prevents proper contact between shoe and coulter. Hardfacing must be as neat as possible so as to avoid warping. Make sure the down tubes are placed just in between the clearence left by the the coulter and the seed press device. Hardfacing on the lower area of the shoe must be very neat so as to ensure good shoe-coulter contact. Check the shoe can swing freely on the fixing bolt. 8

10 SEEDING SHOE OPERATION AND SERVICE. Follow the instructions for proper operation and longer set life. - The shoe (5) must swing freely on the fixing bolt (3). Spring (4) ensures good contact between disc blade (7) and shoe (5). Swinging allows for shoe self-cleaning during seeding. If the soil were too wet, some manual cleaning would be needed. If there s no pressure between the shoe and the disc blade, spring(4) will have to be changed. - The drop bolt (2) must not cancel the spring (4) action since it would prevent self-cleaning and maintenance with eventual damage to the system cm in the lower area should be the minimum clearance between disc and shoe. - Check there is a constant contact between shoe (5) and disc (7). If the instructions were ignored the system may be damaged and the following problems may occur: - Quick and uneven shoe wear (5). - Quick wear of bolt holes in the main unit (). - Quick wear of shoe bolt hole (5). - Breakage of disc holder hub bolts (7). - Breakage of shoe bolts (5). IMPORTANT: - See shoe adjustment outline next page. 9

A The shoe (5) must be bolted to the main holder fixing holes (A); right bolting position will depend on soil condition and on disc wear. The shoe can be bolted to the upper hole in order to.

11 A The shoe (5) must be bolted to the main holder fixing holes (A); right bolting position will depend on soil condition and on disc wear. The shoe can be bolted to the upper hole in order to. - Compensate coulter wear. - Reduce shoe wear with deep seeding practices. - Reduce trash storing between shoe and coulter. The shoe can be bolted to the lower hole in order to: - Seed at 30mm deep or even shallower. - Seed over heavy trash. - Use a wear shoe together with a new coulter. - Get even seeding depths when sowing at high speedlar. Caution: Always ensure a minimum of 5-0mm of disc below the seeding shoe otherwise damage may occur to the main arm of the unit. At this point of disc wear you have the option to move the shoe into the next hole position above or replace the coulter disc. 0

12 A The drop bolt (2) must let the shoe swing freely (2.5cm) so that a self-cleaning action can take place. If it is too tight against the shoe the spring will not work and the set will wear faster or break as blockage will be produce. An advantage of tight fitting is the possiblility of working on damp soils. SHOE ADJUSTMENT The drop bolt must allow for a 2.5 cm swing between coulter and how for selfcleaning. 2 7 Check the spring for strong shoe pressure against the coulter. Check pressure by swinging the sheo on the bolt. 3 Tight the self stopping nut so that it does not prevent the shoe from swinging on its bolt. 4 5

13 2- MAIN HOLDER. It is made up by a strong nodular cast reinforced holder which features heat treated bushings and zerks for a longer component life. Advantages of proper greasing: a) Prevents friction between two metallic surfaces B) Prevents rusting c) Protects bushings and bearings from dust and dirt Proper greasing ensures satisfactory performance. Make sure the zerks are not clogged and in good working condition. Change them if necessary. 2

14 3- DISC HOLDER HUB PRE-LOAD BUSHING HUB. ASSEMBLY: It is assembled with a spacer pre-load bushing and three steel nuts. The hub set wears better and ensures more accurate seeding. It can be re-adjusted when slack appears by taking some of the nuts away. ADJUSTMENT: Use a torquemeter at a pressure of 5 kg. Start by rotating the coulter until the torquemeter indicates adjustment is completed. SET FINAL CHECK: Check the coulter for free rotation by driving it forward by hand. Make sure there is no rubbing between shoe and coulter or between coulter and tyre. Check the axle and the hub for slack. If no slack is noticed, the spacer is in the right position CONICAL BEARING HUB. CONICAL BEARING SQUARE HEAD BOLT BUSHING 8730 DBH SEAL 6908 DUST GUARD SEAL 575 PRE LOAD BUSHING WASHER ZERK HUB DUST GUARD 3

4- PRESS WHEEL. The hub can be built in the rim for non-demanding tasks while heavy duty work needs bearing and seal wrought hubs. An adjustable spring regulates wheel pressure as needed.

15 4- PRESS WHEEL. The hub can be built in the rim for non-demanding tasks while heavy duty work needs bearing and seal wrought hubs. An adjustable spring regulates wheel pressure as needed. Swing the seed pressing device and check for undesirable rubbing against the seeding shoe plastic tubes. IMPORTANT: - Minimum spring pressure is advised for soft dry soils and for preventing mud from sticking on the wheels. - Maximum spring pressure is used for deep seeding at greater depths. 4

16 SEED PRESS SYSTEM ADJUSTMENT The spring must not get in the way of the grease gun. The spring lock must be right in the middle of the slide. The seed pressing device must be flat with the holes at 90. Lubricate the pressing device through the zerk until grease is seen on the sides of the bushing. The zerk must be positioned so that the spring is not in the way. Use the grease gun tip to check for right zerk position. The autostop nut must be adjusted so that 2 or 3 thread screws pass. Swing the seed pressing device in order to check spring action and to make sure the device swings freely. 2.5 mm maximum warp is advisable for the press wheel which is assembled following seed delivery sense. 5

17 5- COVER WHEEL. There are two alternatives to cover the furrow: The first system is made up by a cast cover wheel which presses the soil and covers the furrow on the shoe side. The wheel must be near the seeding line on clayish soils while it should be farther apart if seeding on sandy ground. Number of washers determine cover wheel position. This system does not feature the bearing on the wheel but on the holder which protects the bearings from dirt. The second system is made up by two wheels placed on both sides of the forrow for proper seed covering. These wheels can feature 4 notched disc blades (43-E3) for a stronger covering action. 6

requirements. Wheel angle can be adjusted.

18 A torsion spring with three adjustment points controls the pressure on the covering system as for soil requirements. Wheel angle can be adjusted. The function of the wheels is to bring earth into the furrow (See picture below). 7

19 COVER WHEEL ADJUSTMENT. Lubricate the assembly through the zerk until grease can be seen on the sides of the bushing. The zerk must be position so that the spring is not in the way. Use the grease gun tip to check for right zerk position. 80º-90º The autostop nut must be adjusted so that 2 or 3 thread screws pass. The cap and the nut must be fully glued with thread glue. Check seguer before putting the cap. Check the axle for smooth rotation. IMPORTANT: Strong pressure is needed for proper furrow covering. Make sure the spring fittings are at 80 /90. 8

20 COVER WHEEL ADJUSTMENT. Lubricate the assembly through the zerk until grease can be seen on the sides of the bushing. The zerk must be position so that the spring is not in the way. Use the grease gun tip to check for right zerk position. 80º-90º The autostop nut must be adjusted so that 2 or 3 thread screws pass. Adjust in middle position without glueing. IMPORTANT: Strong pressure is needed for proper furrow covering. Make sure the spring fittings are at 80 /90. 9

21 6- LEVELLING WHEEL. The levelling wheel ar designed to wrought hub and double bearings for heavy work. To increase wheel life under severe working conditions some extra non-ribbed bolts have been added. 20

slight contact with the disc when the drill is at work.

22 The 3mm opening between the lip of the tyre and the coulter is aimed at reducing tyre wear. It is adjusted by means of steel washers and it allows the wheel to come into slight contact with the disc when the drill is at work. A special tool for displacing a punched plaque in one way or the other is used to adjust levelling wheel position. 2

23 7- COMPRESSION SYSTEM. It is made up by a first quality, highly resistant helicoidal spring which can resist heavy loads during the seeding process. Check the separator tube is well shaped to ensure free circualtion through the cast bushing. After changing a consumable, assembly the system carefully and check nut pressure to prevent them from becoming loose and the tube from getting out of shape. COMPRESSION SYSTEM ADJUSTMENT. Lubricate the system through both zerks until grease can be seen. Tight the nuts at 2kg/cm2. Do not glue nuts. Check the tube is in good shape. Use only one machined washer on each side. Charge Kgs. Arrow mm Tight the nut at 5 kg/cm2 so as not to damage the tube ends. Remove burr to free the way for the tube. Tight nut to its limit taking care not to damage the tube. The tube must pass easily through the cast bushing. If an obstacle is met the system will not work and the tube, the bolts and the clamps will break. 22

24 FIELD ADJUSTMENT. FOLLOW THE INSTRUCTIONS FOR PROPER ADJUSTMENT: Adjust seeding unit thoroughly. - Adjust seeding depth. Reduce pressure on the cover wheels and on the press wheel. Use the handle to adjust seeding depth on the punched plaque going up or down one hole at a time. When you get to the desired depth adjust unit spring compression to prevent the wheel from leaving a deep track on the ground or the body from being lifted. Depth must be checked with the drill travelling at working speed. The seeding unit MUST NEITHER work over the ground NOR press it so hard as to leave a deep track. 2- Adjust press wheel pressure until there is good contact between seed- furrow bottom. 3- Adjust cover wheels until getting the desired seed coverage. In order to bring earth into the furrow adjust the wheels and exert torsion on the spring. Reduced stirring is achieved by assembling the notched devices on the inner side. Replace them when working on high stalk trash. 4- Adjust the remaining units the same way. 5- Try the drill at seeding speed in order to check general performance. You may need to adjust the cycle of the cylinder commanding the seeding units. 23

25 S P A R E P A R T S LIST OF CONTENTS LEFT/RIGHT STANDARD SEEDING UNIT (OPTIONS) X 6.00MM COULTER SET ½ X 5 WHEEL WHIT CONIC FITTING...33 X 0 VULCANIZED WHEEL WITH WROUGHT HUB (OPTION)...34 HUB IAR X 0 WHEEL (SPECIAL AUSTRALIA)...36 BEAVERTAIL SET ½ X 5 WHEEL WITH CAST HUB (OPTION)...38 LEVELLING WHEEL CAST HUB...39 LEFT/RIGHT DOUBLE WHEEL CAST HOLDER SET WITH NOTCHED DISC...40 LEFT/RIGHT (L) HUB...4 LEFT/RIGHT DISC SCRAPER SET...42 LEFT/RIGT DOUBLE COVER WHEEL HOLDER ADJUSTABLE COMPRESSION SYSTEM..43 X 2 WHEEL WITH NOTCHED DISC SET...44 LEFT/RIGHT SINGLE AND DOUBLE COVER WHEEL CAST ARM SET LEFT/RIGT COVER WHEEL HOLDER ADJUSTABLE COMPRESSION SYSTEM...46 LEFT/RIGHT HARDFACED SEEDING SHOE SET...47 LEFT/RIGHT CAST HOLDER SET...48 COMPRESSION SYSTEM FIXING SET...49 GROOVED AXLE SET GROOVED AXLE PLATE SET SPECIAL AXLE BUSHING SET MADE IN

26 PLACING SPARE PARTS ORDERS. WHEN ORDERING SPARE PARTS KINDLY INDICATE THE FOLLOWING DATA: - ITEM N. 2 - DESCRIPTION. 3 - QUANTITY. In order to determine whether the required spare part is left or right, look at the implement from behind. The levelling wheel will be on your left or on your right. If there is no Ingersoll s agent in your area, indicate addressee s name and means of delivery to INGERSOLL SALES DIVISION Facsimile: ingersoll@ingersollarg.com.ar FOR BETTER PERFORMANCE USE INGERSOLL ORIGINAL PARTS AND FITTINGS.

27 LEFT/RIGHT STANDARD SEEDING UNIT AND OPTIONS. Part.Number Description Unit /6 R.W G5 Autostop Nut /8 R.W G5 Z.D Autostop Nut /8 N.F G5 Z.D Autostop Nut /4 R.W G5 Z.D Autostop Nut ½ R.W Hexagonal Nut Golden Zinc 5/8 G5 Hexagonal Nut Holder Upper Plate Holder Pivot Axle Washer Compression System Fitting Set -Pag Clasp Washer I/D Left/Right Hardfaced Shoe -Pag Press Wheel Arm with Lock /8 x 3 N.F G5 Z.D Hexagonal Head Bolt /2 x 03mm R.W 7/6 G2 Z.D Special Bolt /8 x 4 ¼ R.W G5 Z.D Hexagonal Head Bolt /4 x 5 R.W G5 Z.D Hexagonal Head Bolt /2 x 2 3/4 R.W Square Head Drop Bolt Lower Support Plate Main Holder Pivot Axle (Single Zerk) I/D Left/Right Cast Main Holder Set -Pag Clasp Pin Bolt and Spring Holder Spring Stop Tube Compression Spring Main Holder Spring Stop Plate Spring O Ring Adjustment Plate Lock Bolt Adjustment Plate Lock Spring Press Wheel Rotatory Bushing Cover Wheel Rotatory Bushing I/D Left/Right Cover Wheel Arm Spring. Continue to page Note: Letter D indicates Right-Hand, Letter I indicates Left-Hand. 28

28 LEFT / RIGHT STANDARD SEEDING UNIT AND OPTIONS OPTIONAL Cover Wheel Holder Adjustable Compression System. PAGE 46 4-I/D I/D I/D 48 I/D I/D I/D I/D OPTIONAL Cover Wheel Cast Holder Set. PAGE I/D 67-B I/D D B 2 -I/D B OPTIONAL x 0 Wheel. PAGE 34 OPTIONAL 3 ¾ x 5 Wheel Whit Conic Fitting. PAGE 33 OPTIONAL Beavertail Set PAGE 37 29

29 LEFT/RIGHT STANDARD SEEDING UNIT AND OPTIONS. Part.Number Description Unit Compression System Stop 50mm Washer Compression System Stop 30mm Washer Press Wheel Rotatory Bushing External Washer Cover Wheel Rotatory Bushing External Washer B Washer. (Thread 3/4 ) Levelling Wheel Adjustment Plate and Spacer 3 Washer. (Thread 3/4 ) I/D Left/Right Cover Wheel Cast Horder Set Pag. 45 (optional) D 5/8 R.UNF.G5 Z.D. Thick. 2mm AutoStop Nut I/D C/D Left/Right Cover Double Wheel and Disc Cast Arm Set -Pag 40- x 0 Cast Hub Press Wheel Set -Pag x 0 Whell Special Australia Optional -Pag x 6 x 2mm Flat Washer x6mm Coulter Set -Pag B I/D Left/Right Grooved Axle Set -Pag Special Axle Bushing Set -Pag Grooved Axle Plate Set -Pag I/D Left/Right Seed Press Device Spring x40x0.25mm SAE 070 Washer x20.2x3.2mm Z.D Flat Washer x40mm Split Cotter B 3/4 Thread N.F G5 Z.D Castle Nut /8 90 Bent Zerk I/D Left/Right 3/4 Levelling Wheel Hub Axle I/D Wheel and Cast Hub Set -Page 39- Optional x 20 x 2mm Flat Washer x 20 x 0.2mm Fitting Washer I/D Left/Right Disc Scraper Set -Page 42- Optional AD x 2 Blanck Wheel and Disc Blade Beavertail Set -Page 37- Optional. 30

30 LEFT / RIGHT STANDARD SEEDING UNIT AND OPTIONS OPTIONAL Cover Wheel Holder Adjustable Compression System. PAGE 46 4-I/D I/D I/D 48 I/D I/D I/D I/D OPTIONAL Cover Wheel Cast Holder Set. PAGE I/D 67-B I/D D B 2 -I/D B OPTIONAL x 0 Wheel. PAGE 34 OPTIONAL 3 ¾ x 5 Wheel Whit Conic Fitting. PAGE 33 OPTIONAL Beavertail Set PAGE 37 3

31 8 x 6,00 mm. COULTER BLADE SET. Part. Number: IAR Code Number: A 286-FF0 Part.Number Description Unit Full Coulter Set R.W G5 ZD 3/8 Standard Nut Seal. 286-FF0 8 x 6mm Plain Coulter Conical Bearing /8 x R.W G5 Z.D Square Head Bolt x 6mm Machined Disc Holder Hub /4 Straight Washer Seal A Assembled Hub ,4 x 30 x 36mm Pre Load Bushing x 30 x 36mm Fitting Washer. 3 32

32 4 ½ x 5 WHEEL WHIT CONIC FITTING. Part. Number: IAR A Code Number: SUP Part.Number Description Unit ½ x 5-2,5mm. (Yellow) Half Rim SUP Conic Fitting ¾ x 5 (2098) Wheel Tyre /6 R.W. G2 Z.D. 0.5mm. Autostop Nut /6 x 5/8 R.W. G2 Z.D. Hexagonal Head Bolt. 6 33

33 VULCANIZED x 0 WHEEL WHIT OPTIONAL CAST HUB. Part. Number: IAR Code Number: D 55-6 Part.Number Description Unit Full Cast Hub Wheel D 5/8 R.W. G5 Z.D.Thickness 9,5mm. AutoStop Nut /4 R.W G2 Z.D AutoStop Nut /4 x 5/8 R.W G2 Z.D Hexagonal Head Bolt Hub x 0 Press Wheel and Tyre x 6 x 2mm Flat Washer. 2 34

34 IAR HUB. P. Number: IAR D P. Number: IAR I Código Comp: Código Comp: D/I D/I Part.Number Description Unit D/I 5/8 R.UNF Z.D. Thickness.:2mm. Autostop Nut Fine Grain Press Wheel Hub D/I Right/Left Fine Grain Press Wheel Axle Press Wheel Hub Retainer Support Press Wheel Dust Guard N 5053 Seal x6x2mm Flat Washer DIN 472 Seeger Ring RSH Bearing. 2 35

35 x 0 WHEELL. SPECIAL AUSTRALIA P. Number: IAR A D P. Number: IAR A I Code Number: Code Number: D/I Part. Number Description Unit /4 R.W. G2 Z.D Autostop Nut x 0 Stamped Hub Half Rim x 0 (0060) Tyre /4 x 3/4 R.W. G2 Z.D Hexagonal Head Bolt. 3 36

36 BEAVERTAIL SET. P. Number: IAR-0898 Code Number: Part. Number Description Unit /4 x 3/4 R.W G2 Golden Zink Hexagonal Head Bolt Plastic Beavertail U-Shaped Holder /8 G5 R.W Golden Zink Autostop Nut /8 x /4 R.W G5 Golden Zink Hexagonal Headed Bolt K Plastic Beavertail. 37

37 4 ½ x 5 WHEEL WITH OPTIONAL CAST HUB. P. Number: IAR I/D Yellow P. Number: IAR I/D Black Code Number: 32/305 Code Number: 3/ / Part.Number Description Unit I/D B/Y Black/Yellow Assembled Set ½ x 5 Wheel Tyre / Black/Yellow 4 ½ x 5 Half Rim I/D Cast Hub /6 x R.W G2 Z.D Hexagonal Head Bolt /6 R.W. G2 Z.D. AutoStop Nut /6 x 5/8 R.W G2 Z.D Hexagonal Head Bolt. 6 38

38 LEVELLING WHEEL CAST HUB P.Number: IAR I/D Code Number: 0350/ I/D Part Number Description Unit x 20 x 2mm.Golden Zink Flat Washer /4 Levelling Wheel Hub Dust Guard Seal Holder Ring DBH 9094 Seal DIN 472 D 47 Seeger Ring RSH 6204 Bearing x20.5x.2mm. Non-Standard Fitting Washer DBH 5422 Seal Levelling Wheel Hub /4 90 Bent Zerk D/I Left/Right 3/4 Unf.Levelling wheel hub axle 39

39 LEFT / RIGHT DOUBLE COVER WHEEL CAST HOLDER SET WITH NOTCHED DISC. P. Number: IAR I/D Yellow P. Number: IAR I/D Black Code Number: 00287/88 Code Number: 00302/ I/D I/D /6-AD / I/D Part.Number Description Unit I/D Full Holder /2 Z.D Flat Washer /2 x 2 ¼ R.W G5 Z.D Hexagonal Head Bolt /2 Grower Washer /2 R.W G5 Z.D Hexagonal Nut I/D Left/Right Cover Double Wheel Cast Holder I/D C/D Full holder with Disc 5-E Cover Wheel Position Adjustment Device I/D x 2 Wheel Hub and Disc Set AD x 2 Wheel and Disc I/D Yellow/Black x 2 Wheel. 40

40 LEFT/RIGHT L HUB SET. Part. Number: IAR I Part. Number: IAR D Code Number: Code Number: D/I I Part Number Description Unit. Ø DIN 472 Seeger Ring Nº 5422 Seal RSH Bearing I 5/8 x 8H UNF Left Nut (Reduce) D/I Right/Left L Hub Axle Leveling Wheel Hub Guard L Hub Bushing RSH Bearing L Cast Hub Cover Wheel Hub Camellón. 4

41 LEFT / RIGHT DISC SCRAPER SET. P. Number: IAR-0879-I/D Code Number: 00684/ Part. Number Description Unit Left/Right Disc Scraper Holder HARDF Left/Right Disc Scraper Coulter /8 x ½ R.W G5 Golden Zink Hexagonal Head Bolt Disc Scraper Spring /8 R.W high.9,2 mm.golden Zink Hexagonal Nut. 42

42 LEFT / RIGHT DOUBLE COVER WHEEL HOLDER ADJUSTABLE COMPRESSIÓN SYSTEM. P. Number: IAR I/D Code Number: 0032/ I/D I/D I/D Part. Number Description Unit I/D Left/Right Front Guide I/D Left/Right Rear Holder I/D Left/Right Rear Holder Lid Nodular Iron Die Pressing Rod Spring Guide Bushing Z.D. 43x60mm. Spring Z.D. Rod Holder Bolt x50mm. Split Pin /6 x ½ R.W G5 Z.D. Hexagon Head Bolt /6 Grower Washers. 5 43

43 x 2 WHEEL AND NOTCHED DISC SET E / Part.Number Description Unit /6 x ¼ R.W G2 Z.D Hexagonal Head Bolt Spacer Bushing /6 Grower Golden Zinc Washer /6 Z.D Hexagonal Nut x 2 Wheel Tyre /6 x 2 x.8mm B/Y Half Rim /6 x 5/8 R.W G2 Z.D Hexagonal Head Bolt E3 4 x 2.5mm Notched Disc. 44

44 LEFT / RIGHT COVER WHEEL CAST HOLDER SET (OPTION). Part. Number: IAR Code Number: I/D I/D 6- I/D 48-2 I/D Part.Number Description Unit I/D Full Set Seeger Ring I/D Left/right 3/4 R.W Special Nut I/D Left/Right 5/8 Thin Thread Nut Bearing I/D Left/Right Cover Wheel Cast Holder Cast Cover Wheel Hub Cap I/D Left/Right Cast Cover Wheel Axle Cast Cover Wheel x 20.2 x 3.2mm Z.D Flat Washer. 5 45

45 LEFT/RIGHT COVER WHEEL HOLDER ADJUSTABLE COMPRESSIÓN SYSTEM. P. Number: IAR I/D Code Number:0030/ 76- I/D I/D I/D Part. Number Description Unit I/D Left/Right Front Guide I/D Left/Right Rear Holder I/D Left/Right Rear Holder Lid Pressing Rod Nodular Iron Die Z.D. 43x234mm.Spring Spring Guide Bushing Z.D. Rod Holder Bolt x50mm.Split Pin /6 x ½ R.W G5 Z.D. Hexagon Head Bolt /6 Grower Washers. 5 46

46 LEFT / RIGHT HARDFACED SEEDING SHOE SET. Part. Number: IAR Code Number: 0024/ I/D I/D 5- Part.Number Description Unit I/D Full Shoe Set I/D Left/Right Machined Hardfaced Seeding Shoe I/D Plate Tubes /6 R.W G5 Z.D. AutoStop Nut /4 G5 Z. Dorado AutoStop Nut Clamp Seeding Shoe Alfa Plastic Tube Seeding Shoe Plain Plastic Tube /6 R.W. G5 Z.D. Milled Head Bolt. 47

47 LEFT / RIGHT CAST HOLDER SET. P.Number: IAR I/D Code Number: 00239/ I/D Part.Number Description Unit I/D Full Holder and Support I/D Left/Right Cast Holder /8 45 Bent Zerk Holder Pivot Bushing Press Wheel Holder Pivot Bushing Cover Wheel Pivot Bushing Press Wheel Holder Stop /2 Thick.2 mm R.W. G5 Z.D. AutoStop Nut /8 Hexagonal Zerk. 2 OPTIONS I/D Non Support Full Holder I/D Holder Pivot bushing. 2 48

48 COMPRESSION SYSTEM FIXING SET. Part. Number: IAR Code Number: Part.Number Description Unit Compression System Fixer Holder Spring Adjusting Bolt /6 x 2 /4 Split Cotter Compression System Set. 49

49 GROOVED AXLE SET. Part. Number: IAR A Code Number: B 2-5 Part.Number Description Unit A Full Grooved Axle Seal. 50

50 GROOVED AXLE PLATE SET. Part. Number: IAR Code Number: 0027 Part.Number Description Unit Full Bushing Plate Adjustment Plate Adjustment Bolt Grooved Axle. 5

51 SPECIAL AXLE BUSHING SET. Part. Number: IAR Code Number: Part.Number Description Unit Full Set O Ring Coulter Hub Dust Guard Special Bushing. 52

52 Row Unit in Lifted Row Unit in Working 53

REPLACING ROLTEC SPRING ARMS

REPLACING ROLTEC SPRING ARMS NOTICE TO INSTALLER: Even if familiar with hardware, read instructions prior to installation as improvements may be made without notice. Always handle components with care.