2014 Corvette Stingray. Install instructions.
|
|
- Walter Hawkins
- 5 years ago
- Views:
Transcription
1 2014 Corvette Stingray Install instructions. GM has made great strides in the much improved baffles in both the valve covers and the valley cover where the crankcase dirty side is evacuated through, but there is still a ton of oil entering the intake air charge from 2 points. One is the dirty side (foul) that is common in the past, the valley cover so a good catchcan will stop that, but the other is the same as the earlier C6 Z06 dry sump tank vent that burps oil into the intake air bridge before on the c6, and now into the baffles on the OEM air box with the C7. Many may have seen the pictures Ron at Vengence posted elsewhere of the bag full of oil they found on the fiorst C7 in, and here is what we found on this brand new one (after the first 3 from Ron):
2
3
4 Here is a step by step pictorial of what we see, and how it is cured: First, we are using the dual valve can with integrated flow controlling checkvalves mounted inline and the RX cleanside separator at the oil sump:
5 Lets look at where the oil ingests, and how the C7 engine 's PCV system works. First, the filtered, MAF measured fresh air enters the drivers side valve cover via this main line from the airbox baffles:
6 Since this we will be correcting with a secondary suction/evac source preventing reversion, or back flow through this into the air box, we are leaving this line intact. Then the passenger side valve cover has two fittings that join and vent through the drysump tank and also connect to the airbox. Then a line runs from the tank to the airbox. This is the problem one as it allows a path for any oil from the tank to "burp" directly into the airbox. So this is removed (note it has insulation on it):
7
8 We then replace the oil fill cap on the sump tank with the RX cleanside oil separator, and connect the enclosed line from the separator to the air box barb left open from removing the OEM line:
9 This now will trap the oil that does "burp" and hold it in the separator during the moments when the oil would exit (during hard cornering, braking, acceleration) and holds it from ingestion until the flow pulls it back in when in full vacuum mode (idle, deceleration, or cruising). So now we have the clean, or fresh side addressed, lets get to the real culprit of steady oil ingestion. This is the U shaped convoluted line that runs from the Intake manifold vacuum barb down to the valley cover barb just below. This is all new for 2014 and has a much improved baffle under the valley cover in an attempt to slow oil ingestion, and the exit barb it'self is now a one-way checkvalve VS the restrictive fixed orifice of the L99 and LS3 versions (that were too restrictive to allow proper evacuation). So props to GM for addressing part of this issue (we have used the checkvalves for 12 years now back with the C5 to correct this issue). So this helps reduce the backflow, or reversion during WOT, but does not eliminate it, and we will get to how we correct that as well. So here is the foul side line (Note the vacuum barb now is on the drivers side of the IM snout VS the passenger side on the gen 3 &4 versions of the LS engine):
10
11
12
13 And the one way checkvalve valley cover barb where all the crankcase vapors along with the oil most and damaging combustion byproducts are evacuated:
14 By simply pressing the tabs, these lines will quick disconnect, and the barbs are 3/8" so the included lines with the RX system slide snugly on all. Now we simply connect the center of the RX can to the valley barb (and since it already is a checkvalve, no additional valve need be installed here):
15 And the primary outlet of the RX can will now connect to the vacuum barb left open after removing the U shaped OEM tube, WITH a checkvalve flowing away from the can (this is to ensure no mixing and reversion) And finally, the secondary outlet with checkvalve flowing away from the can will run to a hole drilled into the coupler just in from of the throttle body. This is going to provide suction for evacuation while in WOT operating mode when vacuum inside the IM is non existent from he reversion pulses present. This will now ensure the flow is always traveling in the right direction, and the checkvalve prevents any backflow. The RX can will separate the oil and other compounds from the vapors and only cleansed vapors are entering the intake air charge preventing the intake valve coking as well as the other oil caused issues most are aware of. Here is the entire system. as it is finished:
16
17
18
RX Catch Can installation& PCV system
RX Catch Can installation& PCV system The LS based motors have a PCV system that at best is pretty ineffective. This allows oil mist to enter the intake manifold causing undue carbon buildup on the piston
More informationRX Monster Catch Can installation & PCV system for Turbo & remote mount supercharger systems
RX Monster Catch Can installation & PCV system for Turbo & remote mount supercharger systems Please note: Depending on the mount location of the head unit, you may need to find an alternate spot to mount
More informationRX Catch Can installation & PCV system for Turbo & remote mount supercharger systems
RX Catch Can installation & PCV system for Turbo & remote mount supercharger systems The LS based motors have a PCV system that at best is pretty ineffective. This allows oil mist to enter the intake manifold
More informationCatch Cans. (For the 5 th Gen Camaro, L99 A6 V8) (For the LS3 M6 V8, see pics at the end)
R X Catch Cans (For the 5 th Gen Camaro, L99 A6 V8) (For the LS3 M6 V8, see pics at the end) What makes the RX performance the most effective oil separating catchcan on the market? There are several factors
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationFunction description of crankcase ventilation. Engine CFI-Jetronic P
01-0400 Function description of crankcase ventilation Engine 104.98 CFI-Jetronic 2 Air admission opening in crankcase 11 Cylinder head cover 2a Opening for oil outlet 12 Air cleaner 3 Gasket 13 Oil separator
More informationOil Module in the Inner V
Oil Module in the Inner V There are numerous oil supply passages under a cover in the V of the engine. The cover is bolted directly to the cylinder block, with a metal gasket positioned between them. Oil
More informationINSTALLATION INSTRUCTIONS Oil Catch Can Kit BMW E46 3-Series/M3 Document# Support:
INSTALLATION INSTRUCTIONS Oil Catch Can Kit BMW E46 3-Series/M3 Document# 19-0055 Support: info@radiumauto.com Qty Description 1 Radium Engineering Anodized and Etched Catch Can Top 1 Radium Engineering
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationInstant Chat off the main page of Or simply call our tech team at
02-07 WRX/STI Air Oil Separator for Top Mounted Intercooler Setups 2013-02- 27 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More information2009 PCED Gasoline Engines SECTION 1: Description and Operation. Intake Air System
2009 PCED Gasoline Engines SECTION 1: Description and Operation Procedure revision date: 05/27/2010 Overview Intake Air Systems The intake air system provides clean air to the engine, optimizes air flow,
More informationAir Oil Separator for WRX/STI Top Mounted Intercooler Setups
Air Oil Separator for 02-07 WRX/STI Top Mounted Intercooler Setups Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More informationLSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body)
LSX Intake Manifold #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) Thank you for your purchase of the most innovative and powerful Gen III (LS1 and LS6) manifold ever developed. We are
More informationTOYOTA FJ CRUISER / 4RUNNER COLD AIR INTAKE Section I Installation Preparation. 4.0L V6 (1GR) Roller Rocker Part Number(s): PTR
Section I Installation Preparation Part Number(s): PTR03-89100 Kit Contents Item # Quantity Reqd. Description 1 1 Air Filter (P/N: PTR43-00083) 2 1 Upper Air Box 3 1 Lower Air Box 4 1 Hump Coupler 5 1
More informationInstant Chat off the main page of Or simply call our tech team at
Subaru WRX/STI Air Oil Separator for Front Mounted Intercooler Setups 2013-02- 22 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT MITSUBISHI EVOLUTION X Document# Customer Support:
The EVOX catch can kit is available in 3 variations. The PCV kit installs between the PCV valve and the intake manifold. The crankcase kit installs between the valve cover vent port and the pre-turbo air
More information2015 Corvette Supercharger System Instructions
2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment
More informationAir Oil Separator for WRX
Air Oil Separator for 2015+ WRX 2018-06-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationBrute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.
Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A
More informationChevy Sonic 1.4L Intake Manifold
Chevy Sonic 1.4L Intake Manifold Install Time: 3 hours In the Box: (1) Racer X Intake manifold (6) M8x1.25 bolts (4) M6x1 bolts (2) 1/8 NPT plugs (1) 3/8 NPT plug (1) 1/4 NPT 90 degree barb (4) Small O-rings
More informationDTC P0106. DTC Descriptor. Manifold Absolute Pressure (MAP) Sensor Performance. Circuit/System Description
DTC Descriptor Manifold Absolute Pressure (MAP) Sensor Performance Circuit/System Description The manifold absolute pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More informationAir Oil Separator for WRX/STI Top Mounted Intercooler Setups
Air Oil Separator for 02-07 WRX/STI Top Mounted Intercooler Setups 2018-02-26 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More information2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body.
2002 Silverado K 4WD Applies to: 4.8L, 5.3L, and 6.0L Report a problem with this article Removal Procedure 1. Remove the air intake duct. Refer to Air Cleaner Resonator Outlet Duct Replacement. 2. Disconnect
More informationInstallation Instructions General Motors 8.1 Sequential Vapor Injection (S.V.I.) System 7500/6500 Series Trucks model year.
Installation Instructions General Motors 8.1 Sequential Vapor Injection (S.V.I.) System 7500/6500 Series Trucks 2003-2005 model year. Technocarb Equipment (2004) Ltd. 4-30435 Progressive Way Abbotsford,
More informationPre-Installed. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS1/6*, 1997-2004 Corvette, 1998-2002 Camaro/Firebird,
More informationSimple Carburettor Fuel System for a Piston Engine. And how it works
Simple Carburettor Fuel System for a Piston Engine And how it works Inlet Exhaust Tank PISTON ENGINE Carburettor Fuel System Filler Cap COCKPIT FUEL GAUGE E FUEL 1/2 F Filler Neck Tank Cavity FUEL LEVEL
More informationA. Perform a vacuum gauge test to determine engine condition and performance.
ENGINE REPAIR UNIT 2: ENGINE DIAGNOSIS, REMOVAL, AND INSTALLATION LESSON 2: ENGINE DIAGNOSTIC TESTS NOTE: Testing the engine s mechanical condition is required when the cause of a problem is not located
More informationModule 5: Emission Control for SI Engines Lecture20:ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS
ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS The Lecture Contains: Crankcase Emission Control (PCV System) Evaporative Emission Control Exhaust Gas Recirculation Water Injection file:///c /...%20and%20Settings/iitkrana1/My%20Documents/Google%20Talk%20Received%20Files/engine_combustion/lecture20/20_1.htm[6/15/2012
More information928 Motorsports Oil Control System for the 16V Porsche 928
928 Motorsports Oil Control System for the 16V Porsche 928 NOTE: Left and Right are always as seen from the driver s seat-as you sit in the car. The following instructions will help you improve the oil
More informationAir Oil Separator for Subaru WRX/STI Front Mounted Intercooler Setups
Air Oil Separator for Subaru WRX/STI Front Mounted Intercooler Setups 2015-01-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More information928 Motorsports Oil Control System Installation
928 Motorsports Oil Control System Installation For 16 valve Non-Supercharged Motors (Installation on supercharged engines is different, and included with the supercharger kit installation instructions)
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationFuel System Diagnosis
Page 1 of 9 1999 Chevrolet Express Express, Savana (VIN G) Service Manual Engine Engine Controls - 5.0L and 5.7L Diagnostic Information and Procedures Document ID: 412957 Fuel System Diagnosis Circuit
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More informationCJV-35/U Underwater Ventilating System
CJV-35/U Underwater Ventilating System CJV-35/U 10328 in the "test tank" at the Willys plant. The driver is wearing a dive suit without the helmet. The test tank was actually just a low road within the
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More informationInstallation Instructions :BMW B58 : Page 1
Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it
More informationPOSITIVE CRANKCASE VENTILATION AND SECONDARY AIR- INJECTION SYSTEMS
85 POSITIVE CRANKCASE VENTILATION AND SECONDARY AIR- INJECTION SYSTEMS Figure 85-1 A PCV valve in a cutaway valve cover, showing the baffles that prevent liquid oil from being drawn into the intake manifold.
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More information2011 Transit Connect Workshop Manual
SECTION 303-12: Intake Air Distribution and Filtering REMOVAL AND INSTALLATION Procedure revision date: 09/23/2010 Intake Air System Components - Exploded View Item Part Number 1 9F991 Throttle Body (TB)
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationHolden VE/VF Commodore. Over The Radiator Intake. Installation Instruction Guide. VE Infill Panel. VE Hood Insert Panel. Twin Fascia Panels
Holden VE/VF Commodore VE Infill Panel Complete the OEM look by covering the hole left after removal of the factory Airbox. Over The Radiator Intake Installation Instruction Guide VE Hood Insert Panel
More informationPART 1: PREPPING OUR C5 FOR A FAST LSX INTAKE MANIFOLD JAMES MILES WORDS PHOTOS
[ TECH] GOING FASTER PART 1: PREPPING OUR C5 FOR A FAST LSX INTAKE MANIFOLD JAMES MILES WORDS PHOTOS Now that we ve sorted out all of our 02 C5 s minor mechanical issues, it s time to get busy with some
More informationACCELERATOR CABLE AND PEDAL
17 ENGINE & EMISSION CONTROL 1996 Engine Control System ACCELERATOR CABLE AND PEDAL REMOVAL AND INSTALLATION Post-installation Operation (Refer to Adjusting the Accelerator Cable.)
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT 2017+ Honda Civic Type-R Document: 19-0193 Support: info@radiumauto.com 20-0424 PCV Catch Can Installation: Follow Steps 1-24 20-0425 CCV Catch Can Installation:
More information2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-511 2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 2003 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 Will not
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationAir Management System Components
AIR M anagement Sys tem Air Management System Components Air Management System Features Series Sequential The series sequential turbocharger is a low pressure/high pressure design working in series with
More informationUse these modules to gain valuable knowledge about STIHL policies, procedures and products that will be a benefit to you on the job immediately.
Bronze Level Training Lesson 09 This is Bronze Level 09 of 10. Welcome to the Service Advantage Bronze Level Training on icademy. These modules are designed to enhance your knowledge base on topics such
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationOregon Fuel Injection
Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear
More informationSDS Continental IO-550 Installation Manual
SDS Continental IO-550 Installation Manual July14/18 This manual covers the steps to install the SDS EM-5 fuel injection and ignition system components on IO-550 engines. Checking Clearance for Hall Sensor
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FIESTA ST Document: 19-0175 Support: info@radiumauto.com STEPS 1-14 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0377) STEPS 15-35 COVER THE CRANKCASE CATCH CAN
More informationSDS Continental O-200 Installation Manual Aug. 4/17
SDS Continental O-200 Installation Manual Aug. 4/17 This manual covers the steps to install the SDS EM-5 fuel injection and ignition system components on O-200 engines. Hall Sensor and Bracket Install
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationZ06 Corvette Lingenfelter High Flow Air Intake
2006-2007 Z06 Corvette Lingenfelter High Flow Air Intake LN4233 1557 Winchester Road Decatur, Indiana 46733 260 724 2552 phone 260 724 8761 fax www.lingenfelter.com Parts List # Part number Description
More informationDTC P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency
Page 1 of 5 1997 Pontiac Grand Prix Grand Prix (VIN W) Service Manual Engine Engine Controls - 3.8L Diagnostic Information and Procedures Document ID: 106986 DTC P0102 Mass Air Flow (MAF) Sensor Circuit
More informationInstallation Instructions for Chevrolet Corvette Lingenfelter High Flow Air Intake System (6.0L LS2 V8 engine)
Installation Instructions for 2005-2007 Chevrolet Corvette Lingenfelter High Flow Air Intake System (6.0L LS2 V8 engine) PN: L650070105 1557 Winchester Road Decatur, Indiana 46733 260 724 2552 phone 260
More informationInstallation Instructions Part Number
Installation Instructions Part Number 84152143 Thank you for choosing Chevrolet Performance as your high performance source. Chevrolet is committed to providing proven, innovative performance technology
More informationOperating and Installation Instructions
Model Number 40401-c (-sp) Electronic Fuel Pump Operating and Installation Instructions This Product is Patent Pending. Application available upon request CAUTION! This product is to be installed only
More informationAdaptive Fuel DTC Diagnostic Techniques
2007 PCED On Board Diagnostics SECTION 2: Diagnostic Methods Procedure revision date: 03/29/2006 Adaptive Fuel DTC Diagnostic Techniques The Adaptive Fuel Diagnostic Trouble Codes (DTC) Diagnostic Techniques
More information2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid Workshop Manual
SECTION 303-08A: Engine Emission 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid Control 2.3L Positive Crankcase Ventilation (PCV) System Components Exploded View View (157 KB) Printable Item Part Number
More informationAIR INDUCTION SYSTEM
Page 1 of 7 PART NUMBER: APPLICATION: 203.60.2505 HONKER C6 2005 07 CORVETTE AIR INDUCTION SYSTEM EXC. Z06 INSTRUCTION SHEET NUMBER: with supercharger 903.60.9852A PACKAGE CONTENTS: Air Box Cover Air Box
More informationG2 INSTALLATION MANUAL
PERFORMANCE ENGINEERED SYSTEMS G2 INSTALLATION MANUAL FOR RACING OR OFF ROAD USE 1 INTRODUCTION PLEASE PURCHASE AUDI- ONLY POWER STEERING FLUID (PENTOSIN CHF 11S) Please note this an older version, and
More information2015 PSI 8.8L LPG Engine Overview. Study Guide. Course Code: 8777
2015 PSI 8.8L LPG Engine Overview Study Guide Course Code: 8777 1 2015 PSI 8.8L LPG Engine Overview Study Guide 2015 Navistar, Inc. 2701 Navistar Drive, Lisle, IL 60532. All rights reserved. No part of
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationINSIDE YOUR HOLLEY CARBURETOR FUEL INLET SYSTEM
INSIDE YOUR HOLLEY CARBURETOR The carburetor is quite simply a fuel metering device that operates under the logical and straightforward laws of physics. It has evolved over the years from a very simple
More informationChevrolet ZL1 Camaro Lingenfelter Air Intake Kit Installation Instructions (LSA engine)
2012-2013 Chevrolet ZL1 Camaro Lingenfelter Air Intake Kit Installation Instructions (LSA engine) PN: L650182012 Revision - 1.6 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationTurner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670
More informationIdle Air Control (IAC) System Diagnosis
2001 Oldsmobile Alero Idle Air Control (IAC) System Diagnosis Circuit Description The idle air control (IAC) valve is located in the throttle body. It consists of a movable pintle, driven by a gear attached
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationBody type location. Model number location. Small Engine Parts
Body type location Model number location Small Engine Parts FUEL PUMP SYSTEM SYSTEMS AND OPERATION The fuel pump on a diaphragm carburetor uses the vacuum and pressure pulse from the engines crankcase
More informationLABOUR ESTIMATE GUIDE
INSTALLATION INSTRUCTIONS FOR 2003-Current Audi S4 (B6 & B7) Includes Sedan, Avant, & Cabriolet These instructions are applicable to vehicles equipped with either manual or automatic tiptronic transmissions
More informationSCION xb L4-2.4L
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-577 2008-2012 SCION xb L4-2.4L AEM Induction Systems 1 (800) 992-3000 WWW: http://www.aemintakes.com PARTS LIST
More informationInternal Combustion Engines
Air and Fuel Induction Lecture 3 1 Outline In this lecture we will discuss the following: A/F mixture preparation in gasoline engines using carburetion. Air Charging technologies: Superchargers Turbochargers
More informationINSTALLATION INSTRUCTIONS DUAL OIL CATCH CAN KIT
INSTALLATION INSTRUCTIONS DUAL OIL CATCH CAN KIT SUBARU WRX FA20F ENGINE Document: 19-0135 Support: info@radiumauto.com This dual catch can kit installs in the right-hand side of the engine bay and intercepts
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationWARNING. Atomic AirForce Intake Manifold for
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS3/L99, 2008-2013 Corvette and 2010-2014 Camaro
More informationRacing Oil Pan Trap-Door Inserts for Chevrolet Corvette (C5)
Racing Oil Pan Trap-Door Inserts for 1997-2004 Chevrolet Corvette (C5) Part No. EGM-202 Made in USA Important: Read these instructions in their entirety prior to installation. Rev 170104 Applications This
More informationCOLD AIR INTAKE INSTALLATION GUIDE FOR VW MKV 2.5L RABBIT (150hp model)
COLD AIR INTAKE INSTALLATION GUIDE FOR VW MKV 2.5L RABBIT 2006-7 (150hp model) NOT CARB APPROVED WARNING: DO NOT BEGIN INSTALLATION PRIOR TO READING THE PRE INSTALL NOTES ON PAGES 2-4 VF ENGINEERING www.vf-engineering.com
More informationSECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE DESCRIPTION AND OPERATION Engine... 303-01A-2 Engine Identification... 303-01A-2 Engine Code Information Label... 303-01A-2 Engine
More informationAEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system!
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-452 2005 FORD Focus L4-2.0L SEE * NOTE 2004 FORD Focus L4-2.3L SEE * NOTE AEM bypass valves are not compatible
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationHolley GM LS Gen III & IV Street Single-Plane Intake Manifold Kits
Holley GM LS Gen III & IV Street Single-Plane Intake Manifold Kits 300-131 LS3 Street Single-Plane Intake Manifold, Carbureted/TB EFI 300-132 LS1/2/6 Street Single-Plane Intake Manifold, Carbureted/TB
More informationVacuum and air hose replacement -- replacing all the old, crusty air and vacuum hoses under and around
Vacuum and air hose replacement -- replacing all the old, crusty air and vacuum hoses under and around the intake manifold. Requires removing the intake manifold. While you've got the intake manifold off,
More information3 WRX/STI TURBO INLET HOSE
3 WRX/STI TURBO INLET HOSE Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationINSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK)
INSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK) FORD FOCUS 2.3L ECOBOOST Document: 19-0155 Support: info@radiumauto.com IMPORTANT NOTES: 1. This installation requires minor metal cutting. Air tools
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED
More informationApplication & Installation Guide. Crankcase Ventilation Systems LEBW
Application & Installation Guide Crankcase Ventilation Systems LEBW4958-04 Contents Crankcase Ventilation Systems... 1 Crankcase Emissions... 2 Blow-by... 2 Crankcase Ventilation... 3 Ingestive... 3 Low
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions
COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322
More informationBill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
More informationInstallation Instructions For The Lingenfelter High Flow LS9 Supercharger Front Cover (6.2L LS9 V8 engine)
Installation Instructions For The Lingenfelter High Flow LS9 Supercharger Front Cover (6.2L LS9 V8 engine) PN: L250110309 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260)
More informationSuggested Installation Instructions for: Chevrolet Z06 Corvette Lingenfelter High Flow Air Intake System (7.
Page 1 Suggested Installation Instructions for: 638-878 2006-2008 Chevrolet Z06 Corvette Lingenfelter High Flow Air Intake System (7.0L LS7 V8 engine) Count on Mid America Motorworks for all your Corvette
More information